4 The following is a consolidated list of the kernel parameters as implemented
5 (mostly) by the __setup() macro and sorted into English Dictionary order
6 (defined as ignoring all punctuation and sorting digits before letters in a
7 case insensitive manner), and with descriptions where known.
9 Module parameters for loadable modules are specified only as the
10 parameter name with optional '=' and value as appropriate, such as:
12 modprobe usbcore blinkenlights=1
14 Module parameters for modules that are built into the kernel image
15 are specified on the kernel command line with the module name plus
16 '.' plus parameter name, with '=' and value if appropriate, such as:
18 usbcore.blinkenlights=1
20 Hyphens (dashes) and underscores are equivalent in parameter names, so
21 log_buf_len=1M print-fatal-signals=1
22 can also be entered as
23 log-buf-len=1M print_fatal_signals=1
26 This document may not be entirely up to date and comprehensive. The command
27 "modinfo -p ${modulename}" shows a current list of all parameters of a loadable
28 module. Loadable modules, after being loaded into the running kernel, also
29 reveal their parameters in /sys/module/${modulename}/parameters/. Some of these
30 parameters may be changed at runtime by the command
31 "echo -n ${value} > /sys/module/${modulename}/parameters/${parm}".
33 The parameters listed below are only valid if certain kernel build options were
34 enabled and if respective hardware is present. The text in square brackets at
35 the beginning of each description states the restrictions within which a
36 parameter is applicable:
38 ACPI ACPI support is enabled.
39 AGP AGP (Accelerated Graphics Port) is enabled.
40 ALSA ALSA sound support is enabled.
41 APIC APIC support is enabled.
42 APM Advanced Power Management support is enabled.
43 AVR32 AVR32 architecture is enabled.
44 AX25 Appropriate AX.25 support is enabled.
45 BLACKFIN Blackfin architecture is enabled.
46 DRM Direct Rendering Management support is enabled.
47 DYNAMIC_DEBUG Build in debug messages and enable them at runtime
48 EDD BIOS Enhanced Disk Drive Services (EDD) is enabled
49 EFI EFI Partitioning (GPT) is enabled
50 EIDE EIDE/ATAPI support is enabled.
51 FB The frame buffer device is enabled.
52 GCOV GCOV profiling is enabled.
53 HW Appropriate hardware is enabled.
54 IA-64 IA-64 architecture is enabled.
55 IMA Integrity measurement architecture is enabled.
56 IOSCHED More than one I/O scheduler is enabled.
57 IP_PNP IP DHCP, BOOTP, or RARP is enabled.
58 IPV6 IPv6 support is enabled.
59 ISAPNP ISA PnP code is enabled.
60 ISDN Appropriate ISDN support is enabled.
61 JOY Appropriate joystick support is enabled.
62 KGDB Kernel debugger support is enabled.
63 KVM Kernel Virtual Machine support is enabled.
64 LIBATA Libata driver is enabled
65 LP Printer support is enabled.
66 LOOP Loopback device support is enabled.
67 M68k M68k architecture is enabled.
68 These options have more detailed description inside of
69 Documentation/m68k/kernel-options.txt.
70 MCA MCA bus support is enabled.
71 MDA MDA console support is enabled.
72 MOUSE Appropriate mouse support is enabled.
73 MSI Message Signaled Interrupts (PCI).
74 MTD MTD (Memory Technology Device) support is enabled.
75 NET Appropriate network support is enabled.
76 NUMA NUMA support is enabled.
77 NFS Appropriate NFS support is enabled.
78 OSS OSS sound support is enabled.
79 PV_OPS A paravirtualized kernel is enabled.
80 PARIDE The ParIDE (parallel port IDE) subsystem is enabled.
81 PARISC The PA-RISC architecture is enabled.
82 PCI PCI bus support is enabled.
83 PCIE PCI Express support is enabled.
84 PCMCIA The PCMCIA subsystem is enabled.
85 PNP Plug & Play support is enabled.
86 PPC PowerPC architecture is enabled.
87 PPT Parallel port support is enabled.
88 PS2 Appropriate PS/2 support is enabled.
89 RAM RAM disk support is enabled.
90 S390 S390 architecture is enabled.
91 SCSI Appropriate SCSI support is enabled.
92 A lot of drivers have their options described inside
93 the Documentation/scsi/ sub-directory.
94 SECURITY Different security models are enabled.
95 SELINUX SELinux support is enabled.
96 APPARMOR AppArmor support is enabled.
97 SERIAL Serial support is enabled.
98 SH SuperH architecture is enabled.
99 SMP The kernel is an SMP kernel.
100 SPARC Sparc architecture is enabled.
101 SWSUSP Software suspend (hibernation) is enabled.
102 SUSPEND System suspend states are enabled.
103 FTRACE Function tracing enabled.
104 TPM TPM drivers are enabled.
105 TS Appropriate touchscreen support is enabled.
106 UMS USB Mass Storage support is enabled.
107 USB USB support is enabled.
108 USBHID USB Human Interface Device support is enabled.
109 V4L Video For Linux support is enabled.
110 VGA The VGA console has been enabled.
111 VT Virtual terminal support is enabled.
112 WDT Watchdog support is enabled.
113 XT IBM PC/XT MFM hard disk support is enabled.
114 X86-32 X86-32, aka i386 architecture is enabled.
115 X86-64 X86-64 architecture is enabled.
116 More X86-64 boot options can be found in
117 Documentation/x86/x86_64/boot-options.txt .
118 X86 Either 32bit or 64bit x86 (same as X86-32+X86-64)
119 XEN Xen support is enabled
121 In addition, the following text indicates that the option:
123 BUGS= Relates to possible processor bugs on the said processor.
124 KNL Is a kernel start-up parameter.
125 BOOT Is a boot loader parameter.
127 Parameters denoted with BOOT are actually interpreted by the boot
128 loader, and have no meaning to the kernel directly.
129 Do not modify the syntax of boot loader parameters without extreme
130 need or coordination with <Documentation/x86/boot.txt>.
132 There are also arch-specific kernel-parameters not documented here.
133 See for example <Documentation/x86/x86_64/boot-options.txt>.
135 Note that ALL kernel parameters listed below are CASE SENSITIVE, and that
136 a trailing = on the name of any parameter states that that parameter will
137 be entered as an environment variable, whereas its absence indicates that
138 it will appear as a kernel argument readable via /proc/cmdline by programs
139 running once the system is up.
141 The number of kernel parameters is not limited, but the length of the
142 complete command line (parameters including spaces etc.) is limited to
143 a fixed number of characters. This limit depends on the architecture
144 and is between 256 and 4096 characters. It is defined in the file
145 ./include/asm/setup.h as COMMAND_LINE_SIZE.
147 Finally, the [KMG] suffix is commonly described after a number of kernel
148 parameter values. These 'K', 'M', and 'G' letters represent the _binary_
149 multipliers 'Kilo', 'Mega', and 'Giga', equalling 2^10, 2^20, and 2^30
150 bytes respectively. Such letter suffixes can also be entirely omitted.
154 Advanced Configuration and Power Interface
155 Format: { force | off | strict | noirq | rsdt }
156 force -- enable ACPI if default was off
157 off -- disable ACPI if default was on
158 noirq -- do not use ACPI for IRQ routing
159 strict -- Be less tolerant of platforms that are not
160 strictly ACPI specification compliant.
161 rsdt -- prefer RSDT over (default) XSDT
162 copy_dsdt -- copy DSDT to memory
164 See also Documentation/power/pm.txt, pci=noacpi
166 acpi_apic_instance= [ACPI, IOAPIC]
168 2: use 2nd APIC table, if available
169 1,0: use 1st APIC table
172 acpi_backlight= [HW,ACPI]
173 acpi_backlight=vendor
175 If set to vendor, prefer vendor specific driver
176 (e.g. thinkpad_acpi, sony_acpi, etc.) instead
177 of the ACPI video.ko driver.
179 acpi.debug_layer= [HW,ACPI,ACPI_DEBUG]
180 acpi.debug_level= [HW,ACPI,ACPI_DEBUG]
182 CONFIG_ACPI_DEBUG must be enabled to produce any ACPI
183 debug output. Bits in debug_layer correspond to a
184 _COMPONENT in an ACPI source file, e.g.,
185 #define _COMPONENT ACPI_PCI_COMPONENT
186 Bits in debug_level correspond to a level in
187 ACPI_DEBUG_PRINT statements, e.g.,
188 ACPI_DEBUG_PRINT((ACPI_DB_INFO, ...
189 The debug_level mask defaults to "info". See
190 Documentation/acpi/debug.txt for more information about
191 debug layers and levels.
193 Enable processor driver info messages:
194 acpi.debug_layer=0x20000000
195 Enable PCI/PCI interrupt routing info messages:
196 acpi.debug_layer=0x400000
197 Enable AML "Debug" output, i.e., stores to the Debug
198 object while interpreting AML:
199 acpi.debug_layer=0xffffffff acpi.debug_level=0x2
200 Enable all messages related to ACPI hardware:
201 acpi.debug_layer=0x2 acpi.debug_level=0xffffffff
203 Some values produce so much output that the system is
204 unusable. The "log_buf_len" parameter may be useful
205 if you need to capture more output.
207 acpi_irq_balance [HW,ACPI]
208 ACPI will balance active IRQs
211 acpi_irq_nobalance [HW,ACPI]
212 ACPI will not move active IRQs (default)
215 acpi_irq_isa= [HW,ACPI] If irq_balance, mark listed IRQs used by ISA
216 Format: <irq>,<irq>...
218 acpi_irq_pci= [HW,ACPI] If irq_balance, clear listed IRQs for
220 Format: <irq>,<irq>...
222 acpi_no_auto_ssdt [HW,ACPI] Disable automatic loading of SSDT
224 acpi_os_name= [HW,ACPI] Tell ACPI BIOS the name of the OS
225 Format: To spoof as Windows 98: ="Microsoft Windows"
227 acpi_osi= [HW,ACPI] Modify list of supported OS interface strings
228 acpi_osi="string1" # add string1 -- only one string
229 acpi_osi="!string2" # remove built-in string2
230 acpi_osi= # disable all strings
233 Override the pmtimer bug detection: force the kernel
234 to assume that this machine's pmtimer latches its value
235 and always returns good values.
237 acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode
238 Format: { level | edge | high | low }
240 acpi_serialize [HW,ACPI] force serialization of AML methods
242 acpi_skip_timer_override [HW,ACPI]
243 Recognize and ignore IRQ0/pin2 Interrupt Override.
244 For broken nForce2 BIOS resulting in XT-PIC timer.
246 acpi_sleep= [HW,ACPI] Sleep options
247 Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig,
248 old_ordering, s4_nonvs, sci_force_enable }
249 See Documentation/power/video.txt for information on
251 s3_beep is for debugging; it makes the PC's speaker beep
252 as soon as the kernel's real-mode entry point is called.
253 s4_nohwsig prevents ACPI hardware signature from being
254 used during resume from hibernation.
255 old_ordering causes the ACPI 1.0 ordering of the _PTS
256 control method, with respect to putting devices into
257 low power states, to be enforced (the ACPI 2.0 ordering
258 of _PTS is used by default).
259 nonvs prevents the kernel from saving/restoring the
260 ACPI NVS memory during suspend/hibernation and resume.
261 sci_force_enable causes the kernel to set SCI_EN directly
262 on resume from S1/S3 (which is against the ACPI spec,
263 but some broken systems don't work without it).
265 acpi_use_timer_override [HW,ACPI]
266 Use timer override. For some broken Nvidia NF5 boards
267 that require a timer override, but don't have HPET
269 acpi_enforce_resources= [ACPI]
270 { strict | lax | no }
271 Check for resource conflicts between native drivers
272 and ACPI OperationRegions (SystemIO and SystemMemory
273 only). IO ports and memory declared in ACPI might be
274 used by the ACPI subsystem in arbitrary AML code and
275 can interfere with legacy drivers.
276 strict (default): access to resources claimed by ACPI
277 is denied; legacy drivers trying to access reserved
278 resources will fail to bind to device using them.
279 lax: access to resources claimed by ACPI is allowed;
280 legacy drivers trying to access reserved resources
281 will bind successfully but a warning message is logged.
282 no: ACPI OperationRegions are not marked as reserved,
283 no further checks are performed.
285 add_efi_memmap [EFI; X86] Include EFI memory map in
286 kernel's map of available physical RAM.
289 { off | try_unsupported }
290 off: disable AGP support
291 try_unsupported: try to drive unsupported chipsets
292 (may crash computer or cause data corruption)
295 See Documentation/sound/alsa/alsa-parameters.txt
298 Allow the default userspace alignment fault handler
299 behaviour to be specified. Bit 0 enables warnings,
300 bit 1 enables fixups, and bit 2 sends a segfault.
302 amd_iommu= [HW,X86-84]
303 Pass parameters to the AMD IOMMU driver in the system.
305 fullflush - enable flushing of IO/TLB entries when
306 they are unmapped. Otherwise they are
307 flushed before they will be reused, which
309 off - do not initialize any AMD IOMMU found in
312 amijoy.map= [HW,JOY] Amiga joystick support
313 Map of devices attached to JOY0DAT and JOY1DAT
315 See also Documentation/kernel/input/joystick.txt
317 analog.map= [HW,JOY] Analog joystick and gamepad support
318 Specifies type or capabilities of an analog joystick
319 connected to one of 16 gameports
320 Format: <type1>,<type2>,..<type16>
323 Power management functions (SPARCstation-4/5 + deriv.)
325 Disable APC CPU standby support. SPARCstation-Fox does
326 not play well with APC CPU idle - disable it if you have
327 APC and your system crashes randomly.
329 apic= [APIC,X86-32] Advanced Programmable Interrupt Controller
330 Change the output verbosity whilst booting
331 Format: { quiet (default) | verbose | debug }
332 Change the amount of debugging information output
333 when initialising the APIC and IO-APIC components.
336 See Documentation/networking/ipv6.txt.
338 show_lapic= [APIC,X86] Advanced Programmable Interrupt Controller
339 Limit apic dumping. The parameter defines the maximal
340 number of local apics being dumped. Also it is possible
341 to set it to "all" by meaning -- no limit here.
342 Format: { 1 (default) | 2 | ... | all }.
343 The parameter valid if only apic=debug or
344 apic=verbose is specified.
345 Example: apic=debug show_lapic=all
347 apm= [APM] Advanced Power Management
348 See header of arch/x86/kernel/apm_32.c.
350 arcrimi= [HW,NET] ARCnet - "RIM I" (entirely mem-mapped) cards
351 Format: <io>,<irq>,<nodeID>
355 atarimouse= [HW,MOUSE] Atari Mouse
357 atkbd.extra= [HW] Enable extra LEDs and keys on IBM RapidAccess,
358 EzKey and similar keyboards
360 atkbd.reset= [HW] Reset keyboard during initialization
362 atkbd.set= [HW] Select keyboard code set
363 Format: <int> (2 = AT (default), 3 = PS/2)
365 atkbd.scroll= [HW] Enable scroll wheel on MS Office and similar
368 atkbd.softraw= [HW] Choose between synthetic and real raw mode
369 Format: <bool> (0 = real, 1 = synthetic (default))
371 atkbd.softrepeat= [HW]
372 Use software keyboard repeat
376 baycom_epp= [HW,AX25]
379 baycom_par= [HW,AX25] BayCom Parallel Port AX.25 Modem
381 See header of drivers/net/hamradio/baycom_par.c.
383 baycom_ser_fdx= [HW,AX25]
384 BayCom Serial Port AX.25 Modem (Full Duplex Mode)
385 Format: <io>,<irq>,<mode>[,<baud>]
386 See header of drivers/net/hamradio/baycom_ser_fdx.c.
388 baycom_ser_hdx= [HW,AX25]
389 BayCom Serial Port AX.25 Modem (Half Duplex Mode)
390 Format: <io>,<irq>,<mode>
391 See header of drivers/net/hamradio/baycom_ser_hdx.c.
393 boot_delay= Milliseconds to delay each printk during boot.
394 Values larger than 10 seconds (10000) are changed to
398 bootmem_debug [KNL] Enable bootmem allocator debug messages.
400 bttv.card= [HW,V4L] bttv (bt848 + bt878 based grabber cards)
401 bttv.radio= Most important insmod options are available as
403 bttv.pll= See Documentation/video4linux/bttv/Insmod-options
404 bttv.tuner= and Documentation/video4linux/bttv/CARDLIST
406 bulk_remove=off [PPC] This parameter disables the use of the pSeries
407 firmware feature for flushing multiple hpte entries
410 c101= [NET] Moxa C101 synchronous serial card
412 cachesize= [BUGS=X86-32] Override level 2 CPU cache size detection.
413 Sometimes CPU hardware bugs make them report the cache
414 size incorrectly. The kernel will attempt work arounds
415 to fix known problems, but for some CPUs it is not
416 possible to determine what the correct size should be.
417 This option provides an override for these situations.
420 [SECURITY] Disable capabilities. This would normally
421 be used only if an alternative security model is to be
422 configured. Potentially dangerous and should only be
423 used if you are entirely sure of the consequences.
425 ccw_timeout_log [S390]
426 See Documentation/s390/CommonIO for details.
428 cgroup_disable= [KNL] Disable a particular controller
429 Format: {name of the controller(s) to disable}
430 {Currently supported controllers - "memory"}
432 checkreqprot [SELINUX] Set initial checkreqprot flag value.
433 Format: { "0" | "1" }
434 See security/selinux/Kconfig help text.
435 0 -- check protection applied by kernel (includes
436 any implied execute protection).
437 1 -- check protection requested by application.
438 Default value is set via a kernel config option.
439 Value can be changed at runtime via
440 /selinux/checkreqprot.
443 See Documentation/s390/CommonIO for details.
445 clock= [BUGS=X86-32, HW] gettimeofday clocksource override.
447 Forces specified clocksource (if available) to be used
448 when calculating gettimeofday(). If specified
449 clocksource is not available, it defaults to PIT.
450 Format: { pit | tsc | cyclone | pmtmr }
452 clocksource= Override the default clocksource
454 Override the default clocksource and use the clocksource
455 with the name specified.
456 Some clocksource names to choose from, depending on
458 [all] jiffies (this is the base, fallback clocksource)
460 [ARM] imx_timer1,OSTS,netx_timer,mpu_timer2,
461 pxa_timer,timer3,32k_counter,timer0_1
463 [X86-32] pit,hpet,tsc;
464 scx200_hrt on Geode; cyclone on IBM x440
472 clearcpuid=BITNUM [X86]
473 Disable CPUID feature X for the kernel. See
474 arch/x86/include/asm/cpufeature.h for the valid bit
475 numbers. Note the Linux specific bits are not necessarily
476 stable over kernel options, but the vendor specific
478 Also note that user programs calling CPUID directly
479 or using the feature without checking anything
480 will still see it. This just prevents it from
481 being used by the kernel or shown in /proc/cpuinfo.
482 Also note the kernel might malfunction if you disable
485 cmo_free_hint= [PPC] Format: { yes | no }
486 Specify whether pages are marked as being inactive
487 when they are freed. This is used in CMO environments
488 to determine OS memory pressure for page stealing by
492 code_bytes [X86] How many bytes of object code to print
497 com20020= [HW,NET] ARCnet - COM20020 chipset
499 <io>[,<irq>[,<nodeID>[,<backplane>[,<ckp>[,<timeout>]]]]]
501 com90io= [HW,NET] ARCnet - COM90xx chipset (IO-mapped buffers)
505 ARCnet - COM90xx chipset (memory-mapped buffers)
506 Format: <io>[,<irq>[,<memstart>]]
508 condev= [HW,S390] console device
511 console= [KNL] Output console device and options.
513 tty<n> Use the virtual console device <n>.
517 Use the specified serial port. The options are of
518 the form "bbbbpnf", where "bbbb" is the baud rate,
519 "p" is parity ("n", "o", or "e"), "n" is number of
520 bits, and "f" is flow control ("r" for RTS or
521 omit it). Default is "9600n8".
523 See Documentation/serial-console.txt for more
525 Documentation/networking/netconsole.txt for an
528 uart[8250],io,<addr>[,options]
529 uart[8250],mmio,<addr>[,options]
530 Start an early, polled-mode console on the 8250/16550
531 UART at the specified I/O port or MMIO address,
532 switching to the matching ttyS device later. The
533 options are the same as for ttyS, above.
535 If the device connected to the port is not a TTY but a braille
536 device, prepend "brl," before the device type, for instance
538 For now, only VisioBraille is supported.
540 consoleblank= [KNL] The console blank (screen saver) timeout in
541 seconds. Defaults to 10*60 = 10mins. A value of 0
542 disables the blank timer.
545 [KNL] Change the default value for
546 /proc/<pid>/coredump_filter.
547 See also Documentation/filesystems/proc.txt.
549 cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver
551 <first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
553 crashkernel=size[KMG][@offset[KMG]]
554 [KNL] Using kexec, Linux can switch to a 'crash kernel'
555 upon panic. This parameter reserves the physical
556 memory region [offset, offset + size] for that kernel
557 image. If '@offset' is omitted, then a suitable offset
558 is selected automatically. Check
559 Documentation/kdump/kdump.txt for further details.
561 crashkernel=range1:size1[,range2:size2,...][@offset]
562 [KNL] Same as above, but depends on the memory
563 in the running system. The syntax of range is
564 start-[end] where start and end are both
565 a memory unit (amount[KMG]). See also
566 Documentation/kdump/kdump.txt for an example.
571 cs89x0_media= [HW,NET]
572 Format: { rj45 | aui | bnc }
575 See header of drivers/s390/block/dasd_devmap.c.
577 db9.dev[2|3]= [HW,JOY] Multisystem joystick support via parallel port
578 (one device per port)
579 Format: <port#>,<type>
580 See also Documentation/input/joystick-parport.txt
582 ddebug_query= [KNL,DYNAMIC_DEBUG] Enable debug messages at early boot
583 time. See Documentation/dynamic-debug-howto.txt for
586 debug [KNL] Enable kernel debugging (events log level).
589 [KNL] verbose self-tests
591 Print debugging info while doing the locking API
593 We default to 0 (no extra messages), setting it to
594 1 will print _a lot_ more information - normally
595 only useful to kernel developers.
597 debug_objects [KNL] Enable object debugging
600 [KNL] Disable object debugging
602 debugpat [X86] Enable PAT debugging
604 decnet.addr= [HW,NET]
605 Format: <area>[,<node>]
606 See also Documentation/networking/decnet.txt.
609 [same as hugepagesz=] The size of the default
610 HugeTLB page size. This is the size represented by
611 the legacy /proc/ hugepages APIs, used for SHM, and
612 default size when mounting hugetlbfs filesystems.
613 Defaults to the default architecture's huge page size
617 Set number of hash buckets for dentry cache.
620 IO parameters + enable/disable command.
622 digiepca= [HW,SERIAL]
623 See drivers/char/README.epca and
624 Documentation/serial/digiepca.txt.
627 See Documentation/networking/ipv6.txt.
629 disable_ddw [PPC/PSERIES]
630 Disable Dynamic DMA Window support. Use this if
631 to workaround buggy firmware.
634 See Documentation/networking/ipv6.txt.
636 disable_mtrr_cleanup [X86]
637 The kernel tries to adjust MTRR layout from continuous
638 to discrete, to make X server driver able to add WB
639 entry later. This parameter disables that.
641 disable_mtrr_trim [X86, Intel and AMD only]
642 By default the kernel will trim any uncacheable
643 memory out of your available memory pool based on
644 MTRR settings. This parameter disables that behavior,
645 possibly causing your machine to run very slowly.
647 disable_timer_pin_1 [X86]
648 Disable PIN 1 of APIC timer
649 Can be useful to work around chipset bugs.
651 dma_debug=off If the kernel is compiled with DMA_API_DEBUG support,
652 this option disables the debugging code at boot.
654 dma_debug_entries=<number>
655 This option allows to tune the number of preallocated
656 entries for DMA-API debugging code. One entry is
657 required per DMA-API allocation. Use this if the
658 DMA-API debugging code disables itself because the
659 architectural default is too low.
661 dma_debug_driver=<driver_name>
662 With this option the DMA-API debugging driver
663 filter feature can be enabled at boot time. Just
664 pass the driver to filter for as the parameter.
665 The filter can be disabled or changed to another
666 driver later using sysfs.
670 earlycon= [KNL] Output early console device and options.
671 uart[8250],io,<addr>[,options]
672 uart[8250],mmio,<addr>[,options]
673 uart[8250],mmio32,<addr>[,options]
674 Start an early, polled-mode console on the 8250/16550
675 UART at the specified I/O port or MMIO address.
676 MMIO inter-register address stride is either 8bit (mmio)
678 The options are the same as for ttyS, above.
680 earlyprintk= [X86,SH,BLACKFIN]
682 earlyprintk=serial[,ttySn[,baudrate]]
683 earlyprintk=ttySn[,baudrate]
684 earlyprintk=dbgp[debugController#]
686 Append ",keep" to not disable it when the real console
689 Only vga or serial or usb debug port at a time.
691 Currently only ttyS0 and ttyS1 are supported.
693 Interaction with the standard serial driver is not
696 The VGA output is eventually overwritten by the real
699 ekgdboc= [X86,KGDB] Allow early kernel console debugging
702 This is desgined to be used in conjunction with
703 the boot argument: earlyprintk=vga
706 Format: {"off" | "on" | "skip[mbr]"}
708 eisa_irq_edge= [PARISC,HW]
709 See header of drivers/parisc/eisa.c.
712 See comment before function elanfreq_setup() in
713 arch/x86/kernel/cpu/cpufreq/elanfreq.c.
716 Format: {"cfq" | "deadline" | "noop"}
717 See Documentation/block/as-iosched.txt and
718 Documentation/block/deadline-iosched.txt for details.
720 elfcorehdr= [IA64,PPC,SH,X86]
721 Specifies physical address of start of kernel core
722 image elf header. Generally kexec loader will
723 pass this option to capture kernel.
724 See Documentation/kdump/kdump.txt for details.
726 enable_mtrr_cleanup [X86]
727 The kernel tries to adjust MTRR layout from continuous
728 to discrete, to make X server driver able to add WB
729 entry later. This parameter enables that.
731 enable_timer_pin_1 [X86]
732 Enable PIN 1 of APIC timer
733 Can be useful to work around chipset bugs
734 (in particular on some ATI chipsets).
735 The kernel tries to set a reasonable default.
737 enforcing [SELINUX] Set initial enforcing status.
739 See security/selinux/Kconfig help text.
740 0 -- permissive (log only, no denials).
741 1 -- enforcing (deny and log).
743 Value can be changed at runtime via /selinux/enforce.
746 Disable Error Record Serialization Table (ERST)
749 ether= [HW,NET] Ethernet cards parameters
750 This option is obsoleted by the "netdev=" option, which
751 has equivalent usage. See its documentation for details.
755 fail_make_request=[KNL]
756 General fault injection mechanism.
757 Format: <interval>,<probability>,<space>,<times>
758 See also /Documentation/fault-injection/.
761 See Documentation/blockdev/floppy.txt.
763 force_pal_cache_flush
764 [IA-64] Avoid check_sal_cache_flush which may hang on
765 buggy SAL_CACHE_FLUSH implementations. Using this
766 parameter will force ia64_sal_cache_flush to call
767 ia64_pal_cache_flush instead of SAL_CACHE_FLUSH.
770 [FTRACE] will set and start the specified tracer
771 as early as possible in order to facilitate early
774 ftrace_dump_on_oops[=orig_cpu]
775 [FTRACE] will dump the trace buffers on oops.
776 If no parameter is passed, ftrace will dump
777 buffers of all CPUs, but if you pass orig_cpu, it will
778 dump only the buffer of the CPU that triggered the
781 ftrace_filter=[function-list]
782 [FTRACE] Limit the functions traced by the function
783 tracer at boot up. function-list is a comma separated
784 list of functions. This list can be changed at run
785 time by the set_ftrace_filter file in the debugfs
788 ftrace_notrace=[function-list]
789 [FTRACE] Do not trace the functions specified in
790 function-list. This list can be changed at run time
791 by the set_ftrace_notrace file in the debugfs
794 ftrace_graph_filter=[function-list]
795 [FTRACE] Limit the top level callers functions traced
796 by the function graph tracer at boot up.
797 function-list is a comma separated list of functions
798 that can be changed at run time by the
799 set_graph_function file in the debugfs tracing directory.
802 [HW,JOY] Multisystem joystick and NES/SNES/PSX pad
803 support via parallel port (up to 5 devices per port)
804 Format: <port#>,<pad1>,<pad2>,<pad3>,<pad4>,<pad5>
805 See also Documentation/input/joystick-parport.txt
809 gart_fix_e820= [X86_64] disable the fix e820 for K8 GART
813 gcov_persist= [GCOV] When non-zero (default), profiling data for
814 kernel modules is saved and remains accessible via
815 debugfs, even when the module is unloaded/reloaded.
816 When zero, profiling data is discarded and associated
817 debugfs files are removed at module unload time.
819 gpt [EFI] Forces disk with valid GPT signature but
820 invalid Protective MBR to be treated as GPT.
822 hashdist= [KNL,NUMA] Large hashes allocated during boot
823 are distributed across NUMA nodes. Defaults on
824 for 64bit NUMA, off otherwise.
825 Format: 0 | 1 (for off | on)
827 hcl= [IA-64] SGI's Hardware Graph compatibility layer
829 hd= [EIDE] (E)IDE hard drive subsystem geometry
830 Format: <cyl>,<head>,<sect>
833 Disable Hardware Error Source Table (HEST) support;
834 corresponding firmware-first mode error processing
835 logic will be disabled.
837 highmem=nn[KMG] [KNL,BOOT] forces the highmem zone to have an exact
838 size of <nn>. This works even on boxes that have no
839 highmem otherwise. This also works to reduce highmem
840 size on bigger boxes.
842 highres= [KNL] Enable/disable high resolution timer mode.
843 Valid parameters: "on", "off"
847 See Documentation/isdn/README.HiSax.
851 hpet= [X86-32,HPET] option to control HPET usage
852 Format: { enable (default) | disable | force |
854 disable: disable HPET and use PIT instead
855 force: allow force enabled of undocumented chips (ICH4,
857 verbose: show contents of HPET registers during setup
859 hugepages= [HW,X86-32,IA-64] HugeTLB pages to allocate at boot.
860 hugepagesz= [HW,IA-64,PPC,X86-64] The size of the HugeTLB pages.
861 On x86-64 and powerpc, this option can be specified
862 multiple times interleaved with hugepages= to reserve
863 huge pages of different sizes. Valid pages sizes on
864 x86-64 are 2M (when the CPU supports "pse") and 1G
865 (when the CPU supports the "pdpe1gb" cpuinfo flag)
866 Note that 1GB pages can only be allocated at boot time
867 using hugepages= and not freed afterwards.
869 hvc_iucv= [S390] Number of z/VM IUCV hypervisor console (HVC)
870 terminal devices. Valid values: 0..8
871 hvc_iucv_allow= [S390] Comma-separated list of z/VM user IDs.
872 If specified, z/VM IUCV HVC accepts connections
873 from listed z/VM user IDs only.
875 i2c_bus= [HW] Override the default board specific I2C bus speed
876 or register an additional I2C bus that is not
877 registered from board initialization code.
881 i8042.debug [HW] Toggle i8042 debug mode
882 i8042.direct [HW] Put keyboard port into non-translated mode
883 i8042.dumbkbd [HW] Pretend that controller can only read data from
884 keyboard and cannot control its state
885 (Don't attempt to blink the leds)
886 i8042.noaux [HW] Don't check for auxiliary (== mouse) port
887 i8042.nokbd [HW] Don't check/create keyboard port
888 i8042.noloop [HW] Disable the AUX Loopback command while probing
890 i8042.nomux [HW] Don't check presence of an active multiplexing
892 i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX
894 i8042.notimeout [HW] Ignore timeout condition signalled by conroller
895 i8042.reset [HW] Reset the controller during init and cleanup
896 i8042.unlock [HW] Unlock (ignore) the keylock
900 i8k.ignore_dmi [HW] Continue probing hardware even if DMI data
901 indicates that the driver is running on unsupported
903 i8k.force [HW] Activate i8k driver even if SMM BIOS signature
904 does not match list of supported models.
906 [HW] Report power status in /proc/i8k
907 (disabled by default)
908 i8k.restricted [HW] Allow controlling fans only if SYS_ADMIN
912 Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]]
914 ide-core.nodma= [HW] (E)IDE subsystem
915 Format: =0.0 to prevent dma on hda, =0.1 hdb =1.0 hdc
916 .vlb_clock .pci_clock .noflush .nohpa .noprobe .nowerr
917 .cdrom .chs .ignore_cable are additional options
918 See Documentation/ide/ide.txt.
920 ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem
921 Claim all unknown PCI IDE storage controllers.
924 Format: idle=poll, idle=mwait, idle=halt, idle=nomwait
925 Poll forces a polling idle loop that can slightly
926 improve the performance of waking up a idle CPU, but
927 will use a lot of power and make the system run hot.
929 idle=mwait: On systems which support MONITOR/MWAIT but
930 the kernel chose to not use it because it doesn't save
931 as much power as a normal idle loop, use the
932 MONITOR/MWAIT idle loop anyways. Performance should be
933 the same as idle=poll.
934 idle=halt: Halt is forced to be used for CPU idle.
935 In such case C2/C3 won't be used again.
936 idle=nomwait: Disable mwait for CPU C-states
938 ignore_loglevel [KNL]
939 Ignore loglevel setting - this will print /all/
940 kernel messages to the console. Useful for debugging.
943 Set number of hash buckets for inode cache.
946 Format: { "0" | "1" }
947 0 -- integrity auditing messages. (Default)
948 1 -- enable informational integrity auditing messages.
951 Format: { "sha1" | "md5" }
955 Load a policy which meets the needs of the Trusted
956 Computing Base. This means IMA will measure all
957 programs exec'd, files mmap'd for exec, and all files
958 opened for read by uid=0.
962 Run specified binary instead of /sbin/init as init
965 initcall_debug [KNL] Trace initcalls as they are executed. Useful
966 for working out where the kernel is dying during
969 initrd= [BOOT] Specify the location of the initial ramdisk
971 inport.irq= [HW] Inport (ATI XL and Microsoft) busmouse driver
974 intel_iommu= [DMAR] Intel IOMMU driver (DMAR) option
976 Enable intel iommu driver.
978 Disable intel iommu driver.
979 igfx_off [Default Off]
980 By default, gfx is mapped as normal device. If a gfx
981 device has a dedicated DMAR unit, the DMAR unit is
982 bypassed by not enabling DMAR with this option. In
983 this case, gfx device will use physical address for
986 With this option iommu will not optimize to look
987 for io virtual address below 32 bit forcing dual
988 address cycle on pci bus for cards supporting greater
989 than 32 bit addressing. The default is to look
990 for translation below 32 bit and if not available
991 then look in the higher range.
993 With this option on every unmap_single operation will
994 result in a hardware IOTLB flush operation as opposed
995 to batching them for performance.
997 intremap= [X86-64, Intel-IOMMU]
998 Format: { on (default) | off | nosid }
999 on enable Interrupt Remapping (default)
1000 off disable Interrupt Remapping
1001 nosid disable Source ID checking
1005 iomem= Disable strict checking of access to MMIO memory
1006 strict regions from userspace.
1022 io7= [HW] IO7 for Marvel based alpha systems
1023 See comment before marvel_specify_io7 in
1024 arch/alpha/kernel/core_marvel.c.
1026 io_delay= [X86] I/O delay method
1028 Standard port 0x80 based delay
1030 Alternate port 0xed based delay (needed on some systems)
1032 Simple two microseconds delay
1037 See Documentation/filesystems/nfs/nfsroot.txt.
1039 ip2= [HW] Set IO/IRQ pairs for up to 4 IntelliPort boards
1040 See comment before ip2_setup() in
1041 drivers/char/ip2/ip2base.c.
1044 When an interrupt is not handled search all handlers
1045 for it. Intended to get systems with badly broken
1049 When an interrupt is not handled search all handlers
1050 for it. Also check all handlers each timer
1051 interrupt. Intended to get systems with badly broken
1055 Format: <RDP>,<reset>,<pci_scan>,<verbosity>
1057 isolcpus= [KNL,SMP] Isolate CPUs from the general scheduler.
1059 <cpu number>,...,<cpu number>
1061 <cpu number>-<cpu number>
1062 (must be a positive range in ascending order)
1064 <cpu number>,...,<cpu number>-<cpu number>
1066 This option can be used to specify one or more CPUs
1067 to isolate from the general SMP balancing and scheduling
1068 algorithms. You can move a process onto or off an
1069 "isolated" CPU via the CPU affinity syscalls or cpuset.
1070 <cpu number> begins at 0 and the maximum value is
1071 "number of CPUs in system - 1".
1073 This option is the preferred way to isolate CPUs. The
1074 alternative -- manually setting the CPU mask of all
1075 tasks in the system -- can cause problems and
1076 suboptimal load balancer performance.
1080 js= [HW,JOY] Analog joystick
1081 See Documentation/input/joystick.txt.
1085 kernelcore=nn[KMG] [KNL,X86,IA-64,PPC] This parameter
1086 specifies the amount of memory usable by the kernel
1087 for non-movable allocations. The requested amount is
1088 spread evenly throughout all nodes in the system. The
1089 remaining memory in each node is used for Movable
1090 pages. In the event, a node is too small to have both
1091 kernelcore and Movable pages, kernelcore pages will
1092 take priority and other nodes will have a larger number
1093 of kernelcore pages. The Movable zone is used for the
1094 allocation of pages that may be reclaimed or moved
1095 by the page migration subsystem. This means that
1096 HugeTLB pages may not be allocated from this zone.
1097 Note that allocations like PTEs-from-HighMem still
1098 use the HighMem zone if it exists, and the Normal
1099 zone if it does not.
1101 kgdbdbgp= [KGDB,HW] kgdb over EHCI usb debug port.
1102 Format: <Controller#>[,poll interval]
1103 The controller # is the number of the ehci usb debug
1104 port as it is probed via PCI. The poll interval is
1105 optional and is the number seconds in between
1106 each poll cycle to the debug port in case you need
1107 the functionality for interrupting the kernel with
1108 gdb or control-c on the dbgp connection. When
1109 not using this parameter you use sysrq-g to break into
1110 the kernel debugger.
1112 kgdboc= [KGDB,HW] kgdb over consoles.
1113 Requires a tty driver that supports console polling,
1114 or a supported polling keyboard driver (non-usb).
1115 Serial only format: <serial_device>[,baud]
1116 keyboard only format: kbd
1117 keyboard and serial format: kbd,<serial_device>[,baud]
1118 Optional Kernel mode setting:
1119 kms, kbd format: kms,kbd
1120 kms, kbd and serial format: kms,kbd,<ser_dev>[,baud]
1122 kgdbwait [KGDB] Stop kernel execution and enter the
1123 kernel debugger at the earliest opportunity.
1125 kmac= [MIPS] korina ethernet MAC address.
1126 Configure the RouterBoard 532 series on-chip
1127 Ethernet adapter MAC address.
1129 kmemleak= [KNL] Boot-time kmemleak enable/disable
1130 Valid arguments: on, off
1133 kstack=N [X86] Print N words from the kernel stack
1136 kvm.ignore_msrs=[KVM] Ignore guest accesses to unhandled MSRs.
1137 Default is 0 (don't ignore, but inject #GP)
1139 kvm.oos_shadow= [KVM] Disable out-of-sync shadow paging.
1140 Default is 1 (enabled)
1142 kvm.mmu_audit= [KVM] This is a R/W parameter which allows audit
1146 kvm-amd.nested= [KVM,AMD] Allow nested virtualization in KVM/SVM.
1147 Default is 1 (enabled)
1149 kvm-amd.npt= [KVM,AMD] Disable nested paging (virtualized MMU)
1151 Default is 1 (enabled) if in 64bit or 32bit-PAE mode
1153 kvm-intel.bypass_guest_pf=
1154 [KVM,Intel] Disables bypassing of guest page faults
1155 on Intel chips. Default is 1 (enabled)
1157 kvm-intel.ept= [KVM,Intel] Disable extended page tables
1158 (virtualized MMU) support on capable Intel chips.
1159 Default is 1 (enabled)
1161 kvm-intel.emulate_invalid_guest_state=
1162 [KVM,Intel] Enable emulation of invalid guest states
1163 Default is 0 (disabled)
1165 kvm-intel.flexpriority=
1166 [KVM,Intel] Disable FlexPriority feature (TPR shadow).
1167 Default is 1 (enabled)
1169 kvm-intel.unrestricted_guest=
1170 [KVM,Intel] Disable unrestricted guest feature
1171 (virtualized real and unpaged mode) on capable
1172 Intel chips. Default is 1 (enabled)
1174 kvm-intel.vpid= [KVM,Intel] Disable Virtual Processor Identification
1175 feature (tagged TLBs) on capable Intel chips.
1176 Default is 1 (enabled)
1182 lapic [X86-32,APIC] Enable the local APIC even if BIOS
1185 lapic_timer_c2_ok [X86,APIC] trust the local apic timer
1188 libata.dma= [LIBATA] DMA control
1189 libata.dma=0 Disable all PATA and SATA DMA
1190 libata.dma=1 PATA and SATA Disk DMA only
1191 libata.dma=2 ATAPI (CDROM) DMA only
1192 libata.dma=4 Compact Flash DMA only
1193 Combinations also work, so libata.dma=3 enables DMA
1194 for disks and CDROMs, but not CFs.
1196 libata.ignore_hpa= [LIBATA] Ignore HPA limit
1197 libata.ignore_hpa=0 keep BIOS limits (default)
1198 libata.ignore_hpa=1 ignore limits, using full disk
1200 libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume
1204 libata.force= [LIBATA] Force configurations. The format is comma
1205 separated list of "[ID:]VAL" where ID is
1206 PORT[.DEVICE]. PORT and DEVICE are decimal numbers
1207 matching port, link or device. Basically, it matches
1208 the ATA ID string printed on console by libata. If
1209 the whole ID part is omitted, the last PORT and DEVICE
1210 values are used. If ID hasn't been specified yet, the
1211 configuration applies to all ports, links and devices.
1213 If only DEVICE is omitted, the parameter applies to
1214 the port and all links and devices behind it. DEVICE
1215 number of 0 either selects the first device or the
1216 first fan-out link behind PMP device. It does not
1217 select the host link. DEVICE number of 15 selects the
1218 host link and device attached to it.
1220 The VAL specifies the configuration to force. As long
1221 as there's no ambiguity shortcut notation is allowed.
1222 For example, both 1.5 and 1.5G would work for 1.5Gbps.
1223 The following configurations can be forced.
1225 * Cable type: 40c, 80c, short40c, unk, ign or sata.
1226 Any ID with matching PORT is used.
1228 * SATA link speed limit: 1.5Gbps or 3.0Gbps.
1230 * Transfer mode: pio[0-7], mwdma[0-4] and udma[0-7].
1231 udma[/][16,25,33,44,66,100,133] notation is also
1234 * [no]ncq: Turn on or off NCQ.
1236 * nohrst, nosrst, norst: suppress hard, soft
1239 * dump_id: dump IDENTIFY data.
1241 If there are multiple matching configurations changing
1242 the same attribute, the last one is used.
1244 memblock=debug [KNL] Enable memblock debug messages.
1246 load_ramdisk= [RAM] List of ramdisks to load from floppy
1247 See Documentation/blockdev/ramdisk.txt.
1249 lockd.nlm_grace_period=P [NFS] Assign grace period.
1252 lockd.nlm_tcpport=N [NFS] Assign TCP port.
1255 lockd.nlm_timeout=T [NFS] Assign timeout value.
1258 lockd.nlm_udpport=M [NFS] Assign UDP port.
1261 logibm.irq= [HW,MOUSE] Logitech Bus Mouse Driver
1264 loglevel= All Kernel Messages with a loglevel smaller than the
1265 console loglevel will be printed to the console. It can
1266 also be changed with klogd or other programs. The
1267 loglevels are defined as follows:
1269 0 (KERN_EMERG) system is unusable
1270 1 (KERN_ALERT) action must be taken immediately
1271 2 (KERN_CRIT) critical conditions
1272 3 (KERN_ERR) error conditions
1273 4 (KERN_WARNING) warning conditions
1274 5 (KERN_NOTICE) normal but significant condition
1275 6 (KERN_INFO) informational
1276 7 (KERN_DEBUG) debug-level messages
1278 log_buf_len=n[KMG] Sets the size of the printk ring buffer,
1279 in bytes. n must be a power of two. The default
1280 size is set in the kernel config file.
1282 logo.nologo [FB] Disables display of the built-in Linux logo.
1283 This may be used to provide more screen space for
1284 kernel log messages and is useful when debugging
1285 kernel boot problems.
1287 lp=0 [LP] Specify parallel ports to use, e.g,
1288 lp=port[,port...] lp=none,parport0 (lp0 not configured, lp1 uses
1289 lp=reset first parallel port). 'lp=0' disables the
1290 lp=auto printer driver. 'lp=reset' (which can be
1291 specified in addition to the ports) causes
1292 attached printers to be reset. Using
1293 lp=port1,port2,... specifies the parallel ports
1294 to associate lp devices with, starting with
1295 lp0. A port specification may be 'none' to skip
1296 that lp device, or a parport name such as
1297 'parport0'. Specifying 'lp=auto' instead of a
1298 port specification list means that device IDs
1299 from each port should be examined, to see if
1300 an IEEE 1284-compliant printer is attached; if
1301 so, the driver will manage that printer.
1302 See also header of drivers/char/lp.c.
1305 Sets loops_per_jiffy to given constant, thus avoiding
1306 time-consuming boot-time autodetection (up to 250 ms per
1307 CPU). 0 enables autodetection (default). To determine
1308 the correct value for your kernel, boot with normal
1309 autodetection and see what value is printed. Note that
1310 on SMP systems the preset will be applied to all CPUs,
1311 which is likely to cause problems if your CPUs need
1312 significantly divergent settings. An incorrect value
1313 will cause delays in the kernel to be wrong, leading to
1314 unpredictable I/O errors and other breakage. Although
1315 unlikely, in the extreme case this might damage your
1319 Format: <io>,<irq>,<dma>
1321 machvec= [IA64] Force the use of a particular machine-vector
1322 (machvec) in a generic kernel.
1323 Example: machvec=hpzx1_swiotlb
1325 machtype= [Loongson] Share the same kernel image file between different
1327 Example: machtype=lemote-yeeloong-2f-7inch
1329 max_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory greater
1330 than or equal to this physical address is ignored.
1332 maxcpus= [SMP] Maximum number of processors that an SMP kernel
1333 should make use of. maxcpus=n : n >= 0 limits the
1334 kernel to using 'n' processors. n=0 is a special case,
1335 it is equivalent to "nosmp", which also disables
1338 max_loop= [LOOP] Maximum number of loopback devices that can
1344 mce [X86-32] Machine Check Exception
1346 mce=option [X86-64] See Documentation/x86/x86_64/boot-options.txt
1348 md= [HW] RAID subsystems devices and level
1349 See Documentation/md.txt.
1352 Format: <first>,<last>
1353 Specifies range of consoles to be captured by the MDA.
1355 mem=nn[KMG] [KNL,BOOT] Force usage of a specific amount of memory
1356 Amount of memory to be used when the kernel is not able
1357 to see the whole system memory or for test.
1358 [X86-32] Use together with memmap= to avoid physical
1359 address space collisions. Without memmap= PCI devices
1360 could be placed at addresses belonging to unused RAM.
1362 mem=nopentium [BUGS=X86-32] Disable usage of 4MB pages for kernel
1366 [KNL,SH] Allow user to override the default size for
1367 per-device physically contiguous DMA buffers.
1369 memmap=exactmap [KNL,X86] Enable setting of an exact
1370 E820 memory map, as specified by the user.
1371 Such memmap=exactmap lines can be constructed based on
1372 BIOS output or other requirements. See the memmap=nn@ss
1375 memmap=nn[KMG]@ss[KMG]
1376 [KNL] Force usage of a specific region of memory
1377 Region of memory to be used, from ss to ss+nn.
1379 memmap=nn[KMG]#ss[KMG]
1380 [KNL,ACPI] Mark specific memory as ACPI data.
1381 Region of memory to be used, from ss to ss+nn.
1383 memmap=nn[KMG]$ss[KMG]
1384 [KNL,ACPI] Mark specific memory as reserved.
1385 Region of memory to be used, from ss to ss+nn.
1386 Example: Exclude memory from 0x18690000-0x1869ffff
1387 memmap=64K$0x18690000
1389 memmap=0x10000$0x18690000
1391 memory_corruption_check=0/1 [X86]
1392 Some BIOSes seem to corrupt the first 64k of
1393 memory when doing things like suspend/resume.
1394 Setting this option will scan the memory
1395 looking for corruption. Enabling this will
1396 both detect corruption and prevent the kernel
1397 from using the memory being corrupted.
1398 However, its intended as a diagnostic tool; if
1399 repeatable BIOS-originated corruption always
1400 affects the same memory, you can use memmap=
1401 to prevent the kernel from using that memory.
1403 memory_corruption_check_size=size [X86]
1404 By default it checks for corruption in the low
1405 64k, making this memory unavailable for normal
1406 use. Use this parameter to scan for
1407 corruption in more or less memory.
1409 memory_corruption_check_period=seconds [X86]
1410 By default it checks for corruption every 60
1411 seconds. Use this parameter to check at some
1412 other rate. 0 disables periodic checking.
1414 memtest= [KNL,X86] Enable memtest
1416 default : 0 <disable>
1417 Specifies the number of memtest passes to be
1418 performed. Each pass selects another test
1419 pattern from a given set of patterns. Memtest
1420 fills the memory with this pattern, validates
1421 memory contents and reserves bad memory
1422 regions that are detected.
1424 meye.*= [HW] Set MotionEye Camera parameters
1425 See Documentation/video4linux/meye.txt.
1427 mfgpt_irq= [IA-32] Specify the IRQ to use for the
1428 Multi-Function General Purpose Timers on AMD Geode
1431 mfgptfix [X86-32] Fix MFGPT timers on AMD Geode platforms when
1432 the BIOS has incorrectly applied a workaround. TinyBIOS
1433 version 0.98 is known to be affected, 0.99 fixes the
1434 problem by letting the user disable the workaround.
1438 min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this
1439 physical address is ignored.
1441 mini2440= [ARM,HW,KNL]
1442 Format:[0..2][b][c][t]
1444 MINI2440 configuration specification:
1445 0 - The attached screen is the 3.5" TFT
1446 1 - The attached screen is the 7" TFT
1447 2 - The VGA Shield is attached (1024x768)
1448 Leaving out the screen size parameter will not load
1449 the TFT driver, and the framebuffer will be left
1451 b - Enable backlight. The TFT backlight pin will be
1452 linked to the kernel VESA blanking code and a GPIO
1453 LED. This parameter is not necessary when using the
1455 c - Enable the s3c camera interface.
1456 t - Reserved for enabling touchscreen support. The
1457 touchscreen support is not enabled in the mainstream
1458 kernel as of 2.6.30, a preliminary port can be found
1459 in the "bleeding edge" mini2440 support kernel at
1460 http://repo.or.cz/w/linux-2.6/mini2440.git
1463 [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
1464 parameter allows control of the logging verbosity for
1465 the additional memory initialisation checks. A value
1466 of 0 disables mminit logging and a level of 4 will
1467 log everything. Information is printed at KERN_DEBUG
1468 so loglevel=8 may also need to be specified.
1471 [MOUSE] Maximum time between finger touching and
1472 leaving touchpad surface for touch to be considered
1473 a tap and be reported as a left button click (for
1474 touchpads working in absolute mode only).
1476 mousedev.xres= [MOUSE] Horizontal screen resolution, used for devices
1477 reporting absolute coordinates, such as tablets
1478 mousedev.yres= [MOUSE] Vertical screen resolution, used for devices
1479 reporting absolute coordinates, such as tablets
1481 movablecore=nn[KMG] [KNL,X86,IA-64,PPC] This parameter
1482 is similar to kernelcore except it specifies the
1483 amount of memory used for migratable allocations.
1484 If both kernelcore and movablecore is specified,
1485 then kernelcore will be at *least* the specified
1486 value but may be more. If movablecore on its own
1487 is specified, the administrator must be careful
1488 that the amount of memory usable for all allocations
1491 MTD_Partition= [MTD]
1492 Format: <name>,<region-number>,<size>,<offset>
1494 MTD_Region= [MTD] Format:
1495 <name>,<region-number>[,<base>,<size>,<buswidth>,<altbuswidth>]
1498 See drivers/mtd/cmdlinepart.c.
1500 multitce=off [PPC] This parameter disables the use of the pSeries
1501 firmware feature for updating multiple TCE entries
1504 onenand.bdry= [HW,MTD] Flex-OneNAND Boundary Configuration
1506 Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock]
1508 boundary - index of last SLC block on Flex-OneNAND.
1509 The remaining blocks are configured as MLC blocks.
1510 lock - Configure if Flex-OneNAND boundary should be locked.
1511 Once locked, the boundary cannot be changed.
1512 1 indicates lock status, 0 indicates unlock status.
1515 ARM/S3C2412 JIVE boot control
1517 See arch/arm/mach-s3c2412/mach-jive.c
1519 mtouchusb.raw_coordinates=
1520 [HW] Make the MicroTouch USB driver use raw coordinates
1521 ('y', default) or cooked coordinates ('n')
1523 mtrr_chunk_size=nn[KMG] [X86]
1524 used for mtrr cleanup. It is largest continuous chunk
1525 that could hold holes aka. UC entries.
1527 mtrr_gran_size=nn[KMG] [X86]
1528 Used for mtrr cleanup. It is granularity of mtrr block.
1530 Large value could prevent small alignment from
1533 mtrr_spare_reg_nr=n [X86]
1535 Range: 0,7 : spare reg number
1537 Used for mtrr cleanup. It is spare mtrr entries number.
1538 Set to 2 or more if your graphical card needs more.
1540 n2= [NET] SDL Inc. RISCom/N2 synchronous serial card
1542 netdev= [NET] Network devices parameters
1543 Format: <irq>,<io>,<mem_start>,<mem_end>,<name>
1544 Note that mem_start is often overloaded to mean
1545 something different and driver-specific.
1546 This usage is only documented in each driver source
1550 [NETFILTER] Enable connection tracking flow accounting
1551 0 to disable accounting
1552 1 to enable accounting
1555 nfsaddrs= [NFS] Deprecated. Use ip= instead.
1556 See Documentation/filesystems/nfs/nfsroot.txt.
1558 nfsroot= [NFS] nfs root filesystem for disk-less boxes.
1559 See Documentation/filesystems/nfs/nfsroot.txt.
1561 nfsrootdebug [NFS] enable nfsroot debugging messages.
1562 See Documentation/filesystems/nfs/nfsroot.txt.
1564 nfs.callback_tcpport=
1565 [NFS] set the TCP port on which the NFSv4 callback
1566 channel should listen.
1569 [NFS] sets the pathname to the program which is used
1570 to update the NFS client cache entries.
1572 nfs.cache_getent_timeout=
1573 [NFS] sets the timeout after which an attempt to
1574 update a cache entry is deemed to have failed.
1576 nfs.idmap_cache_timeout=
1577 [NFS] set the maximum lifetime for idmapper cache
1581 [NFS] enable 64-bit inode numbers.
1582 If zero, the NFS client will fake up a 32-bit inode
1583 number for the readdir() and stat() syscalls instead
1584 of returning the full 64-bit number.
1585 The default is to return 64-bit inode numbers.
1587 nfs.nfs4_disable_idmapping=
1588 [NFSv4] When set, this option disables the NFSv4
1589 idmapper on the client, but only if the mount
1590 is using the 'sec=sys' security flavour. This may
1591 make migration from legacy NFSv2/v3 systems easier
1592 provided that the server has the appropriate support.
1593 The default is to always enable NFSv4 idmapping.
1595 nmi_debug= [KNL,AVR32,SH] Specify one or more actions to take
1596 when a NMI is triggered.
1597 Format: [state][,regs][,debounce][,die]
1599 nmi_watchdog= [KNL,BUGS=X86] Debugging features for SMP kernels
1600 Format: [panic,][num]
1602 0 - turn nmi_watchdog off
1603 When panic is specified, panic when an NMI watchdog
1605 This is useful when you use a panic=... timeout and
1606 need the box quickly up again.
1608 netpoll.carrier_timeout=
1609 [NET] Specifies amount of time (in seconds) that
1610 netpoll should wait for a carrier. By default netpoll
1613 no387 [BUGS=X86-32] Tells the kernel to use the 387 maths
1614 emulation library even if a 387 maths coprocessor
1618 [HW] Never suspend the console
1619 Disable suspending of consoles during suspend and
1620 hibernate operations. Once disabled, debugging
1621 messages can reach various consoles while the rest
1622 of the system is being put to sleep (ie, while
1623 debugging driver suspend/resume hooks). This may
1624 not work reliably with all consoles, but is known
1625 to work with serial and VGA consoles.
1627 noaliencache [MM, NUMA, SLAB] Disables the allocation of alien
1628 caches in the slab allocator. Saves per-node memory,
1629 but will impact performance.
1633 noapic [SMP,APIC] Tells the kernel to not make use of any
1634 IOAPICs that may be present in the system.
1636 noautogroup Disable scheduler automatic task group creation.
1638 nobats [PPC] Do not use BATs for mapping kernel lowmem
1639 on "Classic" PPC cores.
1643 noclflush [BUGS=X86] Don't use the CLFLUSH instruction
1645 nodelayacct [KNL] Disable per-task delay accounting
1647 nodisconnect [HW,SCSI,M68K] Disables SCSI disconnects.
1649 nodsp [SH] Disable hardware DSP at boot time.
1651 noefi [X86] Disable EFI runtime services support.
1656 On X86-32 available only on PAE configured kernels.
1657 noexec=on: enable non-executable mappings (default)
1658 noexec=off: disable non-executable mappings
1661 This affects only 32-bit executables.
1662 noexec32=on: enable non-executable mappings (default)
1663 read doesn't imply executable mappings
1664 noexec32=off: disable non-executable mappings
1665 read implies executable mappings
1667 nofpu [SH] Disable hardware FPU at boot time.
1669 nofxsr [BUGS=X86-32] Disables x86 floating point extended
1670 register save and restore. The kernel will only save
1671 legacy floating-point registers on task switch.
1673 noxsave [BUGS=X86] Disables x86 extended register state save
1674 and restore using xsave. The kernel will fallback to
1675 enabling legacy floating-point and sse state.
1677 nohlt [BUGS=ARM,SH] Tells the kernel that the sleep(SH) or
1678 wfi(ARM) instruction doesn't work correctly and not to
1679 use it. This is also useful when using JTAG debugger.
1681 no-hlt [BUGS=X86-32] Tells the kernel that the hlt
1682 instruction doesn't work correctly and not to
1685 no_file_caps Tells the kernel not to honor file capabilities. The
1686 only way then for a file to be executed with privilege
1687 is to be setuid root or executed by root.
1689 nohalt [IA-64] Tells the kernel not to use the power saving
1690 function PAL_HALT_LIGHT when idle. This increases
1691 power-consumption. On the positive side, it reduces
1692 interrupt wake-up latency, which may improve performance
1693 in certain environments such as networked servers or
1696 nohz= [KNL] Boottime enable/disable dynamic ticks
1697 Valid arguments: on, off
1700 noiotrap [SH] Disables trapped I/O port accesses.
1702 noirqdebug [X86-32] Disables the code which attempts to detect and
1703 disable unhandled interrupt sources.
1705 no_timer_check [X86,APIC] Disables the code which tests for
1706 broken timer IRQ sources.
1708 noisapnp [ISAPNP] Disables ISA PnP code.
1710 noinitrd [RAM] Tells the kernel not to load any configured
1713 nointremap [X86-64, Intel-IOMMU] Do not enable interrupt
1715 [Deprecated - use intremap=off]
1719 nojitter [IA64] Disables jitter checking for ITC timers.
1721 no-kvmclock [X86,KVM] Disable paravirtualized KVM clock driver
1723 no-kvmapf [X86,KVM] Disable paravirtualized asynchronous page
1726 nolapic [X86-32,APIC] Do not enable or use the local APIC.
1728 nolapic_timer [X86-32,APIC] Do not use the local APIC timer.
1730 noltlbs [PPC] Do not use large page/tlb entries for kernel
1731 lowmem mapping on PPC40x.
1733 nomca [IA-64] Disable machine check abort handling
1735 nomce [X86-32] Machine Check Exception
1737 nomfgpt [X86-32] Disable Multi-Function General Purpose
1738 Timer usage (for AMD Geode machines).
1740 nopat [X86] Disable PAT (page attribute table extension of
1741 pagetables) support.
1743 norandmaps Don't use address space randomization. Equivalent to
1744 echo 0 > /proc/sys/kernel/randomize_va_space
1746 noreplace-paravirt [X86,IA-64,PV_OPS] Don't patch paravirt_ops
1748 noreplace-smp [X86-32,SMP] Don't replace SMP instructions
1749 with UP alternatives
1751 noresidual [PPC] Don't use residual data on PReP machines.
1753 noresume [SWSUSP] Disables resume and restores original swap
1756 no-scroll [VGA] Disables scrollback.
1757 This is required for the Braillex ib80-piezo Braille
1758 reader made by F.H. Papenmeier (Germany).
1762 nosep [BUGS=X86-32] Disables x86 SYSENTER/SYSEXIT support.
1764 nosmp [SMP] Tells an SMP kernel to act as a UP kernel,
1765 and disable the IO APIC. legacy for "maxcpus=0".
1767 nosoftlockup [KNL] Disable the soft-lockup detector.
1769 noswapaccount [KNL] Disable accounting of swap in memory resource
1770 controller. (See Documentation/cgroups/memory.txt)
1772 nosync [HW,M68K] Disables sync negotiation for all devices.
1774 notsc [BUGS=X86-32] Disable Time Stamp Counter
1776 nousb [USB] Disable the USB subsystem
1778 nowatchdog [KNL] Disable the lockup detector (NMI watchdog).
1782 nox2apic [X86-64,APIC] Do not enable x2APIC mode.
1784 nptcg= [IA64] Override max number of concurrent global TLB
1785 purges which is reported from either PAL_VM_SUMMARY or
1788 nr_cpus= [SMP] Maximum number of processors that an SMP kernel
1789 could support. nr_cpus=n : n >= 1 limits the kernel to
1790 supporting 'n' processors. Later in runtime you can not
1791 use hotplug cpu feature to put more cpu back to online.
1792 just like you compile the kernel NR_CPUS=n
1794 nr_uarts= [SERIAL] maximum number of UARTs to be registered.
1796 numa_zonelist_order= [KNL, BOOT] Select zonelist order for NUMA.
1797 one of ['zone', 'node', 'default'] can be specified
1798 This can be set from sysctl after boot.
1799 See Documentation/sysctl/vm.txt for details.
1801 ohci1394_dma=early [HW] enable debugging via the ohci1394 driver.
1802 See Documentation/debugging-via-ohci1394.txt for more
1805 olpc_ec_timeout= [OLPC] ms delay when issuing EC commands
1806 Rather than timing out after 20 ms if an EC
1807 command is not properly ACKed, override the length
1808 of the timeout. We have interrupts disabled while
1809 waiting for the ACK, so if this is set too high
1810 interrupts *may* be lost!
1812 omap_mux= [OMAP] Override bootloader pin multiplexing.
1813 Format: <mux_mode0.mode_name=value>...
1814 For example, to override I2C bus2:
1815 omap_mux=i2c2_scl.i2c2_scl=0x100,i2c2_sda.i2c2_sda=0x100
1817 oprofile.timer= [HW]
1818 Use timer interrupt instead of performance counters
1820 oprofile.cpu_type= Force an oprofile cpu type
1821 This might be useful if you have an older oprofile
1822 userland or if you want common events.
1823 Format: { arch_perfmon }
1824 arch_perfmon: [X86] Force use of architectural
1825 perfmon on Intel CPUs instead of the
1826 CPU specific event set.
1828 oops=panic Always panic on oopses. Default is to just kill the process,
1829 but there is a small probability of deadlocking the machine.
1830 This will also cause panics on machine check exceptions.
1831 Useful together with panic=30 to trigger a reboot.
1834 See Documentation/sound/oss/oss-parameters.txt
1836 panic= [KNL] Kernel behaviour on panic
1839 parkbd.port= [HW] Parallel port number the keyboard adapter is
1840 connected to, default is 0.
1842 parkbd.mode= [HW] Parallel port keyboard adapter mode of operation,
1843 0 for XT, 1 for AT (default is AT).
1846 parport= [HW,PPT] Specify parallel ports. 0 disables.
1847 Format: { 0 | auto | 0xBBB[,IRQ[,DMA]] }
1848 Use 'auto' to force the driver to use any
1849 IRQ/DMA settings detected (the default is to
1850 ignore detected IRQ/DMA settings because of
1851 possible conflicts). You can specify the base
1852 address, IRQ, and DMA settings; IRQ and DMA
1853 should be numbers, or 'auto' (for using detected
1854 settings on that particular port), or 'nofifo'
1855 (to avoid using a FIFO even if it is detected).
1856 Parallel ports are assigned in the order they
1857 are specified on the command line, starting
1860 parport_init_mode= [HW,PPT]
1861 Configure VIA parallel port to operate in
1862 a specific mode. This is necessary on Pegasos
1863 computer where firmware has no options for setting
1864 up parallel port mode and sets it to spp.
1865 Currently this function knows 686a and 8231 chips.
1866 Format: [spp|ps2|epp|ecp|ecpepp]
1869 Halt all CPUs after the first oops has been printed for
1870 the specified number of seconds. This is to be used if
1871 your oopses keep scrolling off the screen.
1876 See header of drivers/block/paride/pcd.c.
1877 See also Documentation/blockdev/paride.txt.
1879 pci=option[,option...] [PCI] various PCI subsystem options:
1880 earlydump [X86] dump PCI config space before the kernel
1882 off [X86] don't probe for the PCI bus
1883 bios [X86-32] force use of PCI BIOS, don't access
1884 the hardware directly. Use this if your machine
1885 has a non-standard PCI host bridge.
1886 nobios [X86-32] disallow use of PCI BIOS, only direct
1887 hardware access methods are allowed. Use this
1888 if you experience crashes upon bootup and you
1889 suspect they are caused by the BIOS.
1890 conf1 [X86] Force use of PCI Configuration
1892 conf2 [X86] Force use of PCI Configuration
1894 noaer [PCIE] If the PCIEAER kernel config parameter is
1895 enabled, this kernel boot option can be used to
1896 disable the use of PCIE advanced error reporting.
1897 nodomains [PCI] Disable support for multiple PCI
1898 root domains (aka PCI segments, in ACPI-speak).
1899 nommconf [X86] Disable use of MMCONFIG for PCI
1901 check_enable_amd_mmconf [X86] check for and enable
1902 properly configured MMIO access to PCI
1903 config space on AMD family 10h CPU
1904 nomsi [MSI] If the PCI_MSI kernel config parameter is
1905 enabled, this kernel boot option can be used to
1906 disable the use of MSI interrupts system-wide.
1907 noioapicquirk [APIC] Disable all boot interrupt quirks.
1908 Safety option to keep boot IRQs enabled. This
1909 should never be necessary.
1910 ioapicreroute [APIC] Enable rerouting of boot IRQs to the
1911 primary IO-APIC for bridges that cannot disable
1912 boot IRQs. This fixes a source of spurious IRQs
1913 when the system masks IRQs.
1914 noioapicreroute [APIC] Disable workaround that uses the
1915 boot IRQ equivalent of an IRQ that connects to
1916 a chipset where boot IRQs cannot be disabled.
1917 The opposite of ioapicreroute.
1918 biosirq [X86-32] Use PCI BIOS calls to get the interrupt
1919 routing table. These calls are known to be buggy
1920 on several machines and they hang the machine
1921 when used, but on other computers it's the only
1922 way to get the interrupt routing table. Try
1923 this option if the kernel is unable to allocate
1924 IRQs or discover secondary PCI buses on your
1926 rom [X86] Assign address space to expansion ROMs.
1927 Use with caution as certain devices share
1928 address decoders between ROMs and other
1930 norom [X86] Do not assign address space to
1931 expansion ROMs that do not already have
1932 BIOS assigned address ranges.
1933 nobar [X86] Do not assign address space to the
1934 BARs that weren't assigned by the BIOS.
1935 irqmask=0xMMMM [X86] Set a bit mask of IRQs allowed to be
1936 assigned automatically to PCI devices. You can
1937 make the kernel exclude IRQs of your ISA cards
1939 pirqaddr=0xAAAAA [X86] Specify the physical address
1940 of the PIRQ table (normally generated
1941 by the BIOS) if it is outside the
1942 F0000h-100000h range.
1943 lastbus=N [X86] Scan all buses thru bus #N. Can be
1944 useful if the kernel is unable to find your
1945 secondary buses and you want to tell it
1946 explicitly which ones they are.
1947 assign-busses [X86] Always assign all PCI bus
1948 numbers ourselves, overriding
1949 whatever the firmware may have done.
1950 usepirqmask [X86] Honor the possible IRQ mask stored
1951 in the BIOS $PIR table. This is needed on
1952 some systems with broken BIOSes, notably
1953 some HP Pavilion N5400 and Omnibook XE3
1954 notebooks. This will have no effect if ACPI
1955 IRQ routing is enabled.
1956 noacpi [X86] Do not use ACPI for IRQ routing
1957 or for PCI scanning.
1958 use_crs [X86] Use PCI host bridge window information
1959 from ACPI. On BIOSes from 2008 or later, this
1960 is enabled by default. If you need to use this,
1961 please report a bug.
1962 nocrs [X86] Ignore PCI host bridge windows from ACPI.
1963 If you need to use this, please report a bug.
1964 routeirq Do IRQ routing for all PCI devices.
1965 This is normally done in pci_enable_device(),
1966 so this option is a temporary workaround
1967 for broken drivers that don't call it.
1968 skip_isa_align [X86] do not align io start addr, so can
1969 handle more pci cards
1970 firmware [ARM] Do not re-enumerate the bus but instead
1971 just use the configuration from the
1972 bootloader. This is currently used on
1973 IXP2000 systems where the bus has to be
1974 configured a certain way for adjunct CPUs.
1975 noearly [X86] Don't do any early type 1 scanning.
1976 This might help on some broken boards which
1977 machine check when some devices' config space
1978 is read. But various workarounds are disabled
1979 and some IOMMU drivers will not work.
1980 bfsort Sort PCI devices into breadth-first order.
1981 This sorting is done to get a device
1982 order compatible with older (<= 2.4) kernels.
1983 nobfsort Don't sort PCI devices into breadth-first order.
1984 cbiosize=nn[KMG] The fixed amount of bus space which is
1985 reserved for the CardBus bridge's IO window.
1986 The default value is 256 bytes.
1987 cbmemsize=nn[KMG] The fixed amount of bus space which is
1988 reserved for the CardBus bridge's memory
1989 window. The default value is 64 megabytes.
1992 [<order of align>@][<domain>:]<bus>:<slot>.<func>[; ...]
1993 Specifies alignment and device to reassign
1994 aligned memory resources.
1995 If <order of align> is not specified,
1996 PAGE_SIZE is used as alignment.
1997 PCI-PCI bridge can be specified, if resource
1998 windows need to be expanded.
1999 ecrc= Enable/disable PCIe ECRC (transaction layer
2000 end-to-end CRC checking).
2001 bios: Use BIOS/firmware settings. This is the
2006 pcie_aspm= [PCIE] Forcibly enable or disable PCIe Active State Power
2009 force Enable ASPM even on devices that claim not to support it.
2010 WARNING: Forcing ASPM on may cause system lockups.
2012 pcie_ports= [PCIE] PCIe ports handling:
2013 auto Ask the BIOS whether or not to use native PCIe services
2014 associated with PCIe ports (PME, hot-plug, AER). Use
2015 them only if that is allowed by the BIOS.
2016 native Use native PCIe services associated with PCIe ports
2018 compat Treat PCIe ports as PCI-to-PCI bridges, disable the PCIe
2021 pcie_pme= [PCIE,PM] Native PCIe PME signaling options:
2022 nomsi Do not use MSI for native PCIe PME signaling (this makes
2023 all PCIe root ports use INTx for all services).
2025 pcmv= [HW,PCMCIA] BadgePAD 4
2028 See Documentation/blockdev/paride.txt.
2030 pdcchassis= [PARISC,HW] Disable/Enable PDC Chassis Status codes at
2033 See arch/parisc/kernel/pdc_chassis.c
2035 percpu_alloc= Select which percpu first chunk allocator to use.
2036 Currently supported values are "embed" and "page".
2037 Archs may support subset or none of the selections.
2038 See comments in mm/percpu.c for details on each
2039 allocator. This parameter is primarily for debugging
2040 and performance comparison.
2043 See Documentation/blockdev/paride.txt.
2046 See Documentation/blockdev/paride.txt.
2048 pirq= [SMP,APIC] Manual mp-table setup
2049 See Documentation/x86/i386/IO-APIC.txt.
2051 plip= [PPT,NET] Parallel port network link
2052 Format: { parport<nr> | timid | 0 }
2053 See also Documentation/parport.txt.
2055 pmtmr= [X86] Manual setup of pmtmr I/O Port.
2056 Override pmtimer IOPort with a hex value.
2060 Enable PNP debug messages. This depends on the
2061 CONFIG_PNP_DEBUG_MESSAGES option.
2067 { on | off | curr | res | no-curr | no-res }
2070 [ISAPNP] Exclude IRQs for the autoconfiguration
2073 [ISAPNP] Exclude DMAs for the autoconfiguration
2075 pnp_reserve_io= [ISAPNP] Exclude I/O ports for the autoconfiguration
2076 Ranges are in pairs (I/O port base and size).
2079 [ISAPNP] Exclude memory regions for the
2081 Ranges are in pairs (memory base and size).
2083 ports= [IP_VS_FTP] IPVS ftp helper module
2085 Up to 8 (IP_VS_APP_MAX_PORTS) ports
2087 Format: <port>,<port>....
2089 print-fatal-signals=
2090 [KNL] debug: print fatal signals
2092 If enabled, warn about various signal handling
2093 related application anomalies: too many signals,
2094 too many POSIX.1 timers, fatal signals causing a
2097 If you hit the warning due to signal overflow,
2098 you might want to try "ulimit -i unlimited".
2102 printk.time= Show timing data prefixed to each printk message line
2103 Format: <bool> (1/Y/y=enable, 0/N/n=disable)
2105 processor.max_cstate= [HW,ACPI]
2106 Limit processor to maximum C-state
2107 max_cstate=9 overrides any DMI blacklist limit.
2109 processor.nocst [HW,ACPI]
2110 Ignore the _CST method to determine C-states,
2111 instead using the legacy FADT method
2113 profile= [KNL] Enable kernel profiling via /proc/profile
2114 Format: [schedule,]<number>
2115 Param: "schedule" - profile schedule points.
2116 Param: <number> - step/bucket size as a power of 2 for
2117 statistical time based profiling.
2118 Param: "sleep" - profile D-state sleeping (millisecs).
2119 Requires CONFIG_SCHEDSTATS
2120 Param: "kvm" - profile VM exits.
2122 prompt_ramdisk= [RAM] List of RAM disks to prompt for floppy disk
2124 See Documentation/blockdev/ramdisk.txt.
2126 psmouse.proto= [HW,MOUSE] Highest PS2 mouse protocol extension to
2127 probe for; one of (bare|imps|exps|lifebook|any).
2128 psmouse.rate= [HW,MOUSE] Set desired mouse report rate, in reports
2130 psmouse.resetafter= [HW,MOUSE]
2131 Try to reset the device after so many bad packets
2134 [HW,MOUSE] Set desired mouse resolution, in dpi.
2135 psmouse.smartscroll=
2136 [HW,MOUSE] Controls Logitech smartscroll autorepeat.
2137 0 = disabled, 1 = enabled (default).
2140 See Documentation/blockdev/paride.txt.
2143 [KNL] Number of legacy pty's. Overwrites compiled-in
2146 quiet [KNL] Disable most log messages
2151 See Documentation/md.txt.
2153 ramdisk_blocksize= [RAM]
2154 See Documentation/blockdev/ramdisk.txt.
2156 ramdisk_size= [RAM] Sizes of RAM disks in kilobytes
2157 See Documentation/blockdev/ramdisk.txt.
2159 rcupdate.blimit= [KNL,BOOT]
2160 Set maximum number of finished RCU callbacks to process
2163 rcupdate.qhimark= [KNL,BOOT]
2164 Set threshold of queued
2165 RCU callbacks over which batch limiting is disabled.
2167 rcupdate.qlowmark= [KNL,BOOT]
2168 Set threshold of queued RCU callbacks below which
2169 batch limiting is re-enabled.
2173 Run specified binary instead of /init from the ramdisk,
2174 used for early userspace startup. See initrd.
2176 reboot= [BUGS=X86-32,BUGS=ARM,BUGS=IA-64] Rebooting mode
2177 Format: <reboot_mode>[,<reboot_mode2>[,...]]
2178 See arch/*/kernel/reboot.c or arch/*/kernel/process.c
2181 [KNL, SMP] Set scheduler's default relax_domain_level.
2182 See Documentation/cgroups/cpusets.txt.
2184 reserve= [KNL,BUGS] Force the kernel to ignore some iomem area
2186 reservetop= [X86-32]
2188 Reserves a hole at the top of the kernel virtual
2193 Set the amount of memory to reserve for BIOS at
2194 the bottom of the address space.
2196 reset_devices [KNL] Force drivers to reset the underlying device
2197 during initialization.
2200 Specify the partition device for software suspend
2202 resume_offset= [SWSUSP]
2203 Specify the offset from the beginning of the partition
2204 given by "resume=" at which the swap header is located,
2205 in <PAGE_SIZE> units (needed only for swap files).
2206 See Documentation/power/swsusp-and-swap-files.txt
2208 hibernate= [HIBERNATION]
2209 noresume Don't check if there's a hibernation image
2210 present during boot.
2211 nocompress Don't compress/decompress hibernation images.
2213 retain_initrd [RAM] Keep initrd memory after extraction
2215 rhash_entries= [KNL,NET]
2216 Set number of hash buckets for route cache
2218 riscom8= [HW,SERIAL]
2219 Format: <io_board1>[,<io_board2>[,...<io_boardN>]]
2221 ro [KNL] Mount root device read-only on boot
2223 root= [KNL] Root filesystem
2225 rootdelay= [KNL] Delay (in seconds) to pause before attempting to
2226 mount the root filesystem
2228 rootflags= [KNL] Set root filesystem mount option string
2230 rootfstype= [KNL] Set root filesystem type
2232 rootwait [KNL] Wait (indefinitely) for root device to show up.
2233 Useful for devices that are detected asynchronously
2234 (e.g. USB and MMC devices).
2236 rw [KNL] Mount root device read-write on boot
2238 S [KNL] Run init in single mode
2241 See drivers/net/irda/sa1100_ir.c.
2243 sbni= [NET] Granch SBNI12 leased line adapter
2245 sched_debug [KNL] Enables verbose scheduler debug messages.
2247 security= [SECURITY] Choose a security module to enable at boot.
2248 If this boot parameter is not specified, only the first
2249 security module asking for security registration will be
2250 loaded. An invalid security module name will be treated
2251 as if no module has been chosen.
2253 selinux= [SELINUX] Disable or enable SELinux at boot time.
2254 Format: { "0" | "1" }
2255 See security/selinux/Kconfig help text.
2258 Default value is set via kernel config option.
2259 If enabled at boot time, /selinux/disable can be used
2260 later to disable prior to initial policy load.
2262 apparmor= [APPARMOR] Disable or enable AppArmor at boot time
2263 Format: { "0" | "1" }
2264 See security/apparmor/Kconfig help text
2267 Default value is set via kernel config option.
2269 serialnumber [BUGS=X86-32]
2272 Maximal number of shapers.
2274 show_msr= [x86] show boot-time MSR settings
2275 Format: { <integer> }
2276 Show boot-time (BIOS-initialized) MSR settings.
2277 The parameter means the number of CPUs to show,
2278 for example 1 means boot CPU only.
2285 slub_debug[=options[,slabs]] [MM, SLUB]
2286 Enabling slub_debug allows one to determine the
2287 culprit if slab objects become corrupted. Enabling
2288 slub_debug can create guard zones around objects and
2289 may poison objects when not in use. Also tracks the
2290 last alloc / free. For more information see
2291 Documentation/vm/slub.txt.
2293 slub_max_order= [MM, SLUB]
2294 Determines the maximum allowed order for slabs.
2295 A high setting may cause OOMs due to memory
2296 fragmentation. For more information see
2297 Documentation/vm/slub.txt.
2299 slub_min_objects= [MM, SLUB]
2300 The minimum number of objects per slab. SLUB will
2301 increase the slab order up to slub_max_order to
2302 generate a sufficiently large slab able to contain
2303 the number of objects indicated. The higher the number
2304 of objects the smaller the overhead of tracking slabs
2305 and the less frequently locks need to be acquired.
2306 For more information see Documentation/vm/slub.txt.
2308 slub_min_order= [MM, SLUB]
2309 Determines the mininum page order for slabs. Must be
2310 lower than slub_max_order.
2311 For more information see Documentation/vm/slub.txt.
2313 slub_nomerge [MM, SLUB]
2314 Disable merging of slabs with similar size. May be
2315 necessary if there is some reason to distinguish
2316 allocs to different slabs. Debug options disable
2317 merging on their own.
2318 For more information see Documentation/vm/slub.txt.
2321 Format: <io1>[,<io2>[,...,<io8>]]
2323 smp-alt-once [X86-32,SMP] On a hotplug CPU system, only
2324 attempt to substitute SMP alternatives once at boot.
2326 smsc-ircc2.nopnp [HW] Don't use PNP to discover SMC devices
2327 smsc-ircc2.ircc_cfg= [HW] Device configuration I/O port
2328 smsc-ircc2.ircc_sir= [HW] SIR base I/O port
2329 smsc-ircc2.ircc_fir= [HW] FIR base I/O port
2330 smsc-ircc2.ircc_irq= [HW] IRQ line
2331 smsc-ircc2.ircc_dma= [HW] DMA channel
2332 smsc-ircc2.ircc_transceiver= [HW] Transceiver type:
2333 0: Toshiba Satellite 1800 (GP data pin select)
2334 1: Fast pin select (default)
2338 [KNL] Should the soft-lockup detector generate panics.
2340 sonypi.*= [HW] Sony Programmable I/O Control Device driver
2341 See Documentation/sonypi.txt
2343 specialix= [HW,SERIAL] Specialix multi-serial port adapter
2344 See Documentation/serial/specialix.txt.
2346 spia_io_base= [HW,MTD]
2352 Enabled the stack tracer on boot up.
2356 Set the STI (builtin display/keyboard on the HP-PARISC
2357 machines) console (graphic card) which should be used
2358 as the initial boot-console.
2359 See also comment in drivers/video/console/sticore.c.
2362 See comment in drivers/video/console/sticore.c.
2365 Format: bpp:<bpp1>[:<bpp2>[:<bpp3>...]]
2367 sunrpc.min_resvport=
2368 sunrpc.max_resvport=
2370 SunRPC servers often require that client requests
2371 originate from a privileged port (i.e. a port in the
2372 range 0 < portnr < 1024).
2373 An administrator who wishes to reserve some of these
2374 ports for other uses may adjust the range that the
2375 kernel's sunrpc client considers to be privileged
2376 using these two parameters to set the minimum and
2377 maximum port values.
2381 Control how the NFS server code allocates CPUs to
2382 service thread pools. Depending on how many NICs
2383 you have and where their interrupts are bound, this
2384 option will affect which CPUs will do NFS serving.
2385 Note: this parameter cannot be changed while the
2386 NFS server is running.
2388 auto the server chooses an appropriate mode
2389 automatically using heuristics
2390 global a single global pool contains all CPUs
2391 percpu one pool for each CPU
2392 pernode one pool for each NUMA node (equivalent
2393 to global on non-NUMA machines)
2395 sunrpc.tcp_slot_table_entries=
2396 sunrpc.udp_slot_table_entries=
2398 Sets the upper limit on the number of simultaneous
2399 RPC calls that can be sent from the client to a
2400 server. Increasing these values may allow you to
2401 improve throughput, but will also increase the
2402 amount of memory reserved for use by the client.
2405 [KNL] Enable accounting of swap in memory resource
2406 controller if no parameter or 1 is given or disable
2407 it if 0 is given (See Documentation/cgroups/memory.txt)
2409 swiotlb= [IA-64] Number of I/O TLB slabs
2413 sysfs.deprecated=0|1 [KNL]
2414 Enable/disable old style sysfs layout for old udev
2415 on older distributions. When this option is enabled
2416 very new udev will not work anymore. When this option
2417 is disabled (or CONFIG_SYSFS_DEPRECATED not compiled)
2418 in older udev will not work anymore.
2419 Default depends on CONFIG_SYSFS_DEPRECATED_V2 set in
2420 the kernel configuration.
2422 sysrq_always_enabled
2424 Ignore sysrq setting - this boot parameter will
2425 neutralize any effect of /proc/sys/kernel/sysrq.
2426 Useful for debugging.
2430 test_suspend= [SUSPEND]
2431 Specify "mem" (for Suspend-to-RAM) or "standby" (for
2432 standby suspend) as the system sleep state to briefly
2433 enter during system startup. The system is woken from
2434 this state using a wakeup-capable RTC alarm.
2436 thash_entries= [KNL,NET]
2437 Set number of hash buckets for TCP connection
2439 thermal.act= [HW,ACPI]
2440 -1: disable all active trip points in all thermal zones
2441 <degrees C>: override all lowest active trip points
2443 thermal.crt= [HW,ACPI]
2444 -1: disable all critical trip points in all thermal zones
2445 <degrees C>: override all critical trip points
2447 thermal.nocrt= [HW,ACPI]
2448 Set to disable actions on ACPI thermal zone
2449 critical and hot trip points.
2451 thermal.off= [HW,ACPI]
2452 1: disable ACPI thermal control
2454 thermal.psv= [HW,ACPI]
2455 -1: disable all passive trip points
2456 <degrees C>: override all passive trip points to this
2459 thermal.tzp= [HW,ACPI]
2460 Specify global default ACPI thermal zone polling rate
2461 <deci-seconds>: poll all this frequency
2462 0: no polling (default)
2465 Force threading of all interrupt handlers except those
2466 marked explicitely IRQF_NO_THREAD.
2470 Specify if the kernel should make use of the cpu
2471 topology informations if the hardware supports these.
2472 The scheduler will make use of these informations and
2473 e.g. base its process migration decisions on it.
2478 tpm_suspend_pcr=[HW,TPM]
2479 Format: integer pcr id
2480 Specify that at suspend time, the tpm driver
2481 should extend the specified pcr with zeros,
2482 as a workaround for some chips which fail to
2483 flush the last written pcr on TPM_SaveState.
2484 This will guarantee that all the other pcrs
2487 trace_buf_size=nn[KMG]
2488 [FTRACE] will set tracing buffer size.
2490 trace_event=[event-list]
2491 [FTRACE] Set and start specified trace events in order
2492 to facilitate early boot debugging.
2493 See also Documentation/trace/events.txt
2495 tsc= Disable clocksource stability checks for TSC.
2497 [x86] reliable: mark tsc clocksource as reliable, this
2498 disables clocksource verification at runtime, as well
2499 as the stability checks done at bootup. Used to enable
2500 high-resolution timer mode on older hardware, and in
2501 virtualized environment.
2502 [x86] noirqtime: Do not use TSC to do irq accounting.
2503 Used to run time disable IRQ_TIME_ACCOUNTING on any
2504 platforms where RDTSC is slow and this accounting
2507 turbografx.map[2|3]= [HW,JOY]
2508 TurboGraFX parallel port interface
2510 <port#>,<js1>,<js2>,<js3>,<js4>,<js5>,<js6>,<js7>
2511 See also Documentation/input/joystick-parport.txt
2513 uhash_entries= [KNL,NET]
2514 Set number of hash buckets for UDP/UDP-Lite connections
2517 [USB] Ignore overcurrent events (default N).
2518 Some badly-designed motherboards generate lots of
2519 bogus events, for ports that aren't wired to
2520 anything. Set this parameter to avoid log spamming.
2521 Note that genuine overcurrent events won't be
2526 Set unknown_nmi_panic=1 early on boot.
2528 usbcore.autosuspend=
2529 [USB] The autosuspend time delay (in seconds) used
2530 for newly-detected USB devices (default 2). This
2531 is the time required before an idle device will be
2532 autosuspended. Devices for which the delay is set
2533 to a negative value won't be autosuspended at all.
2535 usbcore.usbfs_snoop=
2536 [USB] Set to log all usbfs traffic (default 0 = off).
2538 usbcore.blinkenlights=
2539 [USB] Set to cycle leds on hubs (default 0 = off).
2541 usbcore.old_scheme_first=
2542 [USB] Start with the old device initialization
2543 scheme (default 0 = off).
2545 usbcore.use_both_schemes=
2546 [USB] Try the other device initialization scheme
2547 if the first one fails (default 1 = enabled).
2549 usbcore.initial_descriptor_timeout=
2550 [USB] Specifies timeout for the initial 64-byte
2551 USB_REQ_GET_DESCRIPTOR request in milliseconds
2552 (default 5000 = 5.0 seconds).
2555 [USBHID] The interval which mice are to be polled at.
2557 usb-storage.delay_use=
2558 [UMS] The delay in seconds before a new device is
2559 scanned for Logical Units (default 5).
2562 [UMS] A list of quirks entries to supplement or
2563 override the built-in unusual_devs list. List
2564 entries are separated by commas. Each entry has
2565 the form VID:PID:Flags where VID and PID are Vendor
2566 and Product ID values (4-digit hex numbers) and
2567 Flags is a set of characters, each corresponding
2568 to a common usb-storage quirk flag as follows:
2569 a = SANE_SENSE (collect more than 18 bytes
2571 b = BAD_SENSE (don't collect more than 18
2572 bytes of sense data);
2573 c = FIX_CAPACITY (decrease the reported
2574 device capacity by one sector);
2575 h = CAPACITY_HEURISTICS (decrease the
2576 reported device capacity by one
2577 sector if the number is odd);
2578 i = IGNORE_DEVICE (don't bind to this
2580 l = NOT_LOCKABLE (don't try to lock and
2581 unlock ejectable media);
2582 m = MAX_SECTORS_64 (don't transfer more
2583 than 64 sectors = 32 KB at a time);
2584 o = CAPACITY_OK (accept the capacity
2585 reported by the device);
2586 r = IGNORE_RESIDUE (the device reports
2587 bogus residue values);
2588 s = SINGLE_LUN (the device has only one
2590 w = NO_WP_DETECT (don't test whether the
2591 medium is write-protected).
2592 Example: quirks=0419:aaf5:rl,0421:0433:rc
2595 [X86] Flags controlling user PTE allocations.
2597 nohigh = do not allocate PTE pages in
2598 HIGHMEM regardless of setting
2602 vdso=2: enable compat VDSO (default with COMPAT_VDSO)
2603 vdso=1: enable VDSO (default)
2604 vdso=0: disable VDSO mapping
2607 vdso32=2: enable compat VDSO (default with COMPAT_VDSO)
2608 vdso32=1: enable 32-bit VDSO (default)
2609 vdso32=0: disable 32-bit VDSO mapping
2612 vector=percpu: enable percpu vector domain
2614 video= [FB] Frame buffer configuration
2615 See Documentation/fb/modedb.txt.
2617 vga= [BOOT,X86-32] Select a particular video mode
2618 See Documentation/x86/boot.txt and
2619 Documentation/svga.txt.
2620 Use vga=ask for menu.
2621 This is actually a boot loader parameter; the value is
2622 passed to the kernel using a special protocol.
2624 vmalloc=nn[KMG] [KNL,BOOT] Forces the vmalloc area to have an exact
2625 size of <nn>. This can be used to increase the
2626 minimum size (128MB on x86). It can also be used to
2627 decrease the size and leave more room for directly
2630 vmhalt= [KNL,S390] Perform z/VM CP command after system halt.
2633 vmpanic= [KNL,S390] Perform z/VM CP command after kernel panic.
2636 vmpoff= [KNL,S390] Perform z/VM CP command after power off.
2639 vt.cur_default= [VT] Default cursor shape.
2640 Format: 0xCCBBAA, where AA, BB, and CC are the same as
2641 the parameters of the <Esc>[?A;B;Cc escape sequence;
2642 see VGA-softcursor.txt. Default: 2 = underline.
2644 vt.default_blu= [VT]
2645 Format: <blue0>,<blue1>,<blue2>,...,<blue15>
2646 Change the default blue palette of the console.
2647 This is a 16-member array composed of values
2650 vt.default_grn= [VT]
2651 Format: <green0>,<green1>,<green2>,...,<green15>
2652 Change the default green palette of the console.
2653 This is a 16-member array composed of values
2656 vt.default_red= [VT]
2657 Format: <red0>,<red1>,<red2>,...,<red15>
2658 Change the default red palette of the console.
2659 This is a 16-member array composed of values
2665 Set system-wide default UTF-8 mode for all tty's.
2666 Default is 1, i.e. UTF-8 mode is enabled for all
2667 newly opened terminals.
2669 vt.global_cursor_default=
2672 Set system-wide default for whether a cursor
2673 is shown on new VTs. Default is -1,
2674 i.e. cursors will be created by default unless
2675 overridden by individual drivers. 0 will hide
2676 cursors, 1 will display them.
2678 watchdog timers [HW,WDT] For information on watchdog timers,
2679 see Documentation/watchdog/watchdog-parameters.txt
2680 or other driver-specific files in the
2681 Documentation/watchdog/ directory.
2683 x2apic_phys [X86-64,APIC] Use x2apic physical mode instead of
2684 default x2apic cluster mode on platforms
2687 x86_mrst_timer= [X86-32,APBT]
2688 Choose timer option for x86 Moorestown MID platform.
2689 Two valid options are apbt timer only and lapic timer
2690 plus one apbt timer for broadcast timer.
2691 x86_mrst_timer=apbt_only | lapic_and_apbt
2693 xd= [HW,XT] Original XT pre-IDE (RLL encoded) disks.
2694 xd_geo= See header of drivers/block/xd.c.
2696 xen_emul_unplug= [HW,X86,XEN]
2697 Unplug Xen emulated devices
2698 Format: [unplug0,][unplug1]
2699 ide-disks -- unplug primary master IDE devices
2700 aux-ide-disks -- unplug non-primary-master IDE devices
2701 nics -- unplug network devices
2702 all -- unplug all emulated devices (NICs and IDE disks)
2703 unnecessary -- unplugging emulated devices is
2704 unnecessary even if the host did not respond to
2706 never -- do not unplug even if version check succeeds
2708 xirc2ps_cs= [NET,PCMCIA]
2710 <irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
2712 ______________________________________________________________________
2716 Add more DRM drivers.