2 * Copyright (C) 2013 Pavel Machek <pavel@ucw.cz>
3 * Copyright (C) 2013-2014 Aaro Koskinen <aaro.koskinen@iki.fi>
5 * This program is free software; you can redistribute it and/or modify
6 * it under the terms of the GNU General Public License version 2 (or later) as
7 * published by the Free Software Foundation.
12 #include "omap34xx-hs.dtsi"
13 #include <dt-bindings/input/input.h>
17 compatible = "nokia,omap3-n900", "ti,omap3430", "ti,omap3";
26 compatible = "gpio-leds";
28 label = "debug::sleep";
29 gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* gpio162 */
30 linux,default-trigger = "default-on";
31 pinctrl-names = "default";
32 pinctrl-0 = <&debug_leds>;
37 device_type = "memory";
38 reg = <0x80000000 0x10000000>; /* 256 MB */
42 compatible = "gpio-keys";
45 label = "Camera Lens Cover";
46 gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */
47 linux,input-type = <5>; /* EV_SW */
48 linux,code = <0x09>; /* SW_CAMERA_LENS_COVER */
53 label = "Camera Focus";
54 gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */
55 linux,code = <0x210>; /* KEY_CAMERA_FOCUS */
60 label = "Camera Capture";
61 gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */
62 linux,code = <0xd4>; /* KEY_CAMERA */
67 label = "Lock Button";
68 gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */
69 linux,code = <0x98>; /* KEY_SCREENLOCK */
74 label = "Keypad Slide";
75 gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */
76 linux,input-type = <5>; /* EV_SW */
77 linux,code = <0x0a>; /* SW_KEYPAD_SLIDE */
82 label = "Proximity Sensor";
83 gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */
84 linux,input-type = <5>; /* EV_SW */
85 linux,code = <0x0b>; /* SW_FRONT_PROXIMITY */
90 compatible = "nxp,isp1704";
91 nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>;
92 usb-phy = <&usb2_phy>;
96 compatible = "composite-video-connector";
100 tv_connector_in: endpoint {
101 remote-endpoint = <&venc_out>;
107 compatible = "nokia,n900-audio";
109 nokia,cpu-dai = <&mcbsp2>;
110 nokia,audio-codec = <&tlv320aic3x>, <&tlv320aic3x_aux>;
111 nokia,headphone-amplifier = <&tpa6130a2>;
113 tvout-selection-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>; /* 40 */
114 jack-detection-gpios = <&gpio6 17 GPIO_ACTIVE_HIGH>; /* 177 */
115 eci-switch-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* 182 */
116 speaker-amplifier-gpios = <&twl_gpio 7 GPIO_ACTIVE_HIGH>;
119 battery: n900-battery {
120 compatible = "nokia,n900-battery";
121 io-channels = <&twl_madc 0>, <&twl_madc 4>, <&twl_madc 12>;
122 io-channel-names = "temp", "bsi", "vbat";
127 pinctrl-names = "default";
129 uart2_pins: pinmux_uart2_pins {
130 pinctrl-single,pins = <
131 0x14a (PIN_INPUT | MUX_MODE0) /* uart2_rx */
132 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx */
136 uart3_pins: pinmux_uart3_pins {
137 pinctrl-single,pins = <
138 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx */
139 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx */
143 ethernet_pins: pinmux_ethernet_pins {
144 pinctrl-single,pins = <
145 OMAP3_CORE1_IOPAD(0x20b4, PIN_INPUT_PULLDOWN | MUX_MODE4) /* gpmc_ncs3.gpio_54 */
146 OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE4) /* dss_data16.gpio_86 */
147 OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4) /* uart3_rts_sd.gpio_164 */
151 gpmc_pins: pinmux_gpmc_pins {
152 pinctrl-single,pins = <
155 OMAP3_CORE1_IOPAD(0x207a, PIN_OUTPUT | MUX_MODE0) /* gpmc_a1.gpmc_a1 */
156 OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE0) /* gpmc_a2.gpmc_a2 */
157 OMAP3_CORE1_IOPAD(0x207e, PIN_OUTPUT | MUX_MODE0) /* gpmc_a3.gpmc_a3 */
159 /* data lines, gpmc_d0..d7 not muxable according to TRM */
160 OMAP3_CORE1_IOPAD(0x209e, PIN_INPUT | MUX_MODE0) /* gpmc_d8.gpmc_d8 */
161 OMAP3_CORE1_IOPAD(0x20a0, PIN_INPUT | MUX_MODE0) /* gpmc_d9.gpmc_d9 */
162 OMAP3_CORE1_IOPAD(0x20a2, PIN_INPUT | MUX_MODE0) /* gpmc_d10.gpmc_d10 */
163 OMAP3_CORE1_IOPAD(0x20a4, PIN_INPUT | MUX_MODE0) /* gpmc_d11.gpmc_d11 */
164 OMAP3_CORE1_IOPAD(0x20a6, PIN_INPUT | MUX_MODE0) /* gpmc_d12.gpmc_d12 */
165 OMAP3_CORE1_IOPAD(0x20a8, PIN_INPUT | MUX_MODE0) /* gpmc_d13.gpmc_d13 */
166 OMAP3_CORE1_IOPAD(0x20aa, PIN_INPUT | MUX_MODE0) /* gpmc_d14.gpmc_d14 */
167 OMAP3_CORE1_IOPAD(0x20ac, PIN_INPUT | MUX_MODE0) /* gpmc_d15.gpmc_d15 */
170 * gpmc_ncs0, gpmc_nadv_ale, gpmc_noe, gpmc_nwe, gpmc_wait0 not muxable
171 * according to TRM. OneNAND seems to require PIN_INPUT on clock.
173 OMAP3_CORE1_IOPAD(0x20b0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs1.gpmc_ncs1 */
174 OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0) /* gpmc_clk.gpmc_clk */
178 i2c1_pins: pinmux_i2c1_pins {
179 pinctrl-single,pins = <
180 0x18a (PIN_INPUT | MUX_MODE0) /* i2c1_scl */
181 0x18c (PIN_INPUT | MUX_MODE0) /* i2c1_sda */
185 i2c2_pins: pinmux_i2c2_pins {
186 pinctrl-single,pins = <
187 0x18e (PIN_INPUT | MUX_MODE0) /* i2c2_scl */
188 0x190 (PIN_INPUT | MUX_MODE0) /* i2c2_sda */
192 i2c3_pins: pinmux_i2c3_pins {
193 pinctrl-single,pins = <
194 0x192 (PIN_INPUT | MUX_MODE0) /* i2c3_scl */
195 0x194 (PIN_INPUT | MUX_MODE0) /* i2c3_sda */
199 debug_leds: pinmux_debug_led_pins {
200 pinctrl-single,pins = <
201 OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_clkx.gpio_162 */
205 mcspi4_pins: pinmux_mcspi4_pins {
206 pinctrl-single,pins = <
207 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_clk */
208 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_somi */
209 0x160 (PIN_OUTPUT | MUX_MODE1) /* mcspi4_simo */
210 0x166 (PIN_OUTPUT | MUX_MODE1) /* mcspi4_cs0 */
214 mmc1_pins: pinmux_mmc1_pins {
215 pinctrl-single,pins = <
216 0x114 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */
217 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */
218 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */
219 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */
220 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */
221 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */
225 mmc2_pins: pinmux_mmc2_pins {
226 pinctrl-single,pins = <
227 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */
228 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */
229 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */
230 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */
231 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */
232 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */
233 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat4 */
234 0x136 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat5 */
235 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat6 */
236 0x13a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat7 */
240 acx565akm_pins: pinmux_acx565akm_pins {
241 pinctrl-single,pins = <
242 0x0d4 (PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */
246 dss_sdi_pins: pinmux_dss_sdi_pins {
247 pinctrl-single,pins = <
248 0x0c0 (PIN_OUTPUT | MUX_MODE1) /* dss_data10.sdi_dat1n */
249 0x0c2 (PIN_OUTPUT | MUX_MODE1) /* dss_data11.sdi_dat1p */
250 0x0c4 (PIN_OUTPUT | MUX_MODE1) /* dss_data12.sdi_dat2n */
251 0x0c6 (PIN_OUTPUT | MUX_MODE1) /* dss_data13.sdi_dat2p */
253 0x0d8 (PIN_OUTPUT | MUX_MODE1) /* dss_data22.sdi_clkp */
254 0x0da (PIN_OUTPUT | MUX_MODE1) /* dss_data23.sdi_clkn */
258 wl1251_pins: pinmux_wl1251 {
259 pinctrl-single,pins = <
260 0x0ce (PIN_OUTPUT | MUX_MODE4) /* gpio 87 => wl1251 enable */
261 0x05a (PIN_INPUT | MUX_MODE4) /* gpio 42 => wl1251 irq */
265 ssi_pins: pinmux_ssi {
266 pinctrl-single,pins = <
267 0x150 (PIN_INPUT_PULLUP | MUX_MODE1) /* ssi1_rdy_tx */
268 0x14e (PIN_OUTPUT | MUX_MODE1) /* ssi1_flag_tx */
269 0x152 (PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* ssi1_wake_tx (cawake) */
270 0x14c (PIN_OUTPUT | MUX_MODE1) /* ssi1_dat_tx */
271 0x154 (PIN_INPUT | MUX_MODE1) /* ssi1_dat_rx */
272 0x156 (PIN_INPUT | MUX_MODE1) /* ssi1_flag_rx */
273 0x158 (PIN_OUTPUT | MUX_MODE1) /* ssi1_rdy_rx */
274 0x15a (PIN_OUTPUT | MUX_MODE1) /* ssi1_wake */
278 modem_pins: pinmux_modem {
279 pinctrl-single,pins = <
280 0x0ac (PIN_OUTPUT | MUX_MODE4) /* gpio 70 => cmt_apeslpx */
281 0x0b0 (PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* gpio 72 => ape_rst_rq */
282 0x0b2 (PIN_OUTPUT | MUX_MODE4) /* gpio 73 => cmt_rst_rq */
283 0x0b4 (PIN_OUTPUT | MUX_MODE4) /* gpio 74 => cmt_en */
284 0x0b6 (PIN_OUTPUT | MUX_MODE4) /* gpio 75 => cmt_rst */
285 0x15e (PIN_OUTPUT | MUX_MODE4) /* gpio 157 => cmt_bsi */
291 pinctrl-names = "default";
292 pinctrl-0 = <&i2c1_pins>;
294 clock-frequency = <2200000>;
298 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
299 interrupt-parent = <&intc>;
303 #include "twl4030.dtsi"
304 #include "twl4030_omap3.dtsi"
307 regulator-name = "V28";
308 regulator-min-microvolt = <2800000>;
309 regulator-max-microvolt = <2800000>;
310 regulator-always-on; /* due battery cover sensor */
314 regulator-name = "VCSI";
315 regulator-min-microvolt = <1800000>;
316 regulator-max-microvolt = <1800000>;
320 regulator-name = "VMMC2_30";
321 regulator-min-microvolt = <2800000>;
322 regulator-max-microvolt = <3000000>;
326 regulator-name = "VCAM_ANA_28";
327 regulator-min-microvolt = <2800000>;
328 regulator-max-microvolt = <2800000>;
332 regulator-name = "VMMC1";
333 regulator-min-microvolt = <1850000>;
334 regulator-max-microvolt = <3150000>;
338 regulator-name = "V28_A";
339 regulator-min-microvolt = <2800000>;
340 regulator-max-microvolt = <3000000>;
341 regulator-always-on; /* due VIO leak to AIC34 VDDs */
345 regulator-name = "VPLL";
346 regulator-min-microvolt = <1800000>;
347 regulator-max-microvolt = <1800000>;
352 regulator-name = "VSDI_CSI";
353 regulator-min-microvolt = <1800000>;
354 regulator-max-microvolt = <1800000>;
359 regulator-name = "VMMC2_IO_18";
360 regulator-min-microvolt = <1800000>;
361 regulator-max-microvolt = <1800000>;
365 regulator-name = "VIO";
366 regulator-min-microvolt = <1800000>;
367 regulator-max-microvolt = <1800000>;
372 regulator-name = "VINTANA1";
373 /* fixed to 1500000 */
378 regulator-name = "VINTANA2";
379 regulator-min-microvolt = <2750000>;
380 regulator-max-microvolt = <2750000>;
385 regulator-name = "VINTDIG";
386 /* fixed to 1500000 */
392 compatible = "ti,twl4030-audio";
393 ti,enable-vibra = <1>;
397 compatible = "ti,twl4030-power-n900", "ti,twl4030-power-idle-osc-off";
403 linux,keymap = < MATRIX_KEY(0x00, 0x00, KEY_Q)
404 MATRIX_KEY(0x00, 0x01, KEY_O)
405 MATRIX_KEY(0x00, 0x02, KEY_P)
406 MATRIX_KEY(0x00, 0x03, KEY_COMMA)
407 MATRIX_KEY(0x00, 0x04, KEY_BACKSPACE)
408 MATRIX_KEY(0x00, 0x06, KEY_A)
409 MATRIX_KEY(0x00, 0x07, KEY_S)
411 MATRIX_KEY(0x01, 0x00, KEY_W)
412 MATRIX_KEY(0x01, 0x01, KEY_D)
413 MATRIX_KEY(0x01, 0x02, KEY_F)
414 MATRIX_KEY(0x01, 0x03, KEY_G)
415 MATRIX_KEY(0x01, 0x04, KEY_H)
416 MATRIX_KEY(0x01, 0x05, KEY_J)
417 MATRIX_KEY(0x01, 0x06, KEY_K)
418 MATRIX_KEY(0x01, 0x07, KEY_L)
420 MATRIX_KEY(0x02, 0x00, KEY_E)
421 MATRIX_KEY(0x02, 0x01, KEY_DOT)
422 MATRIX_KEY(0x02, 0x02, KEY_UP)
423 MATRIX_KEY(0x02, 0x03, KEY_ENTER)
424 MATRIX_KEY(0x02, 0x05, KEY_Z)
425 MATRIX_KEY(0x02, 0x06, KEY_X)
426 MATRIX_KEY(0x02, 0x07, KEY_C)
427 MATRIX_KEY(0x02, 0x08, KEY_F9)
429 MATRIX_KEY(0x03, 0x00, KEY_R)
430 MATRIX_KEY(0x03, 0x01, KEY_V)
431 MATRIX_KEY(0x03, 0x02, KEY_B)
432 MATRIX_KEY(0x03, 0x03, KEY_N)
433 MATRIX_KEY(0x03, 0x04, KEY_M)
434 MATRIX_KEY(0x03, 0x05, KEY_SPACE)
435 MATRIX_KEY(0x03, 0x06, KEY_SPACE)
436 MATRIX_KEY(0x03, 0x07, KEY_LEFT)
438 MATRIX_KEY(0x04, 0x00, KEY_T)
439 MATRIX_KEY(0x04, 0x01, KEY_DOWN)
440 MATRIX_KEY(0x04, 0x02, KEY_RIGHT)
441 MATRIX_KEY(0x04, 0x04, KEY_LEFTCTRL)
442 MATRIX_KEY(0x04, 0x05, KEY_RIGHTALT)
443 MATRIX_KEY(0x04, 0x06, KEY_LEFTSHIFT)
444 MATRIX_KEY(0x04, 0x08, KEY_F10)
446 MATRIX_KEY(0x05, 0x00, KEY_Y)
447 MATRIX_KEY(0x05, 0x08, KEY_F11)
449 MATRIX_KEY(0x06, 0x00, KEY_U)
451 MATRIX_KEY(0x07, 0x00, KEY_I)
452 MATRIX_KEY(0x07, 0x01, KEY_F7)
453 MATRIX_KEY(0x07, 0x02, KEY_F8)
459 ti,pulldowns = <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
463 pinctrl-names = "default";
464 pinctrl-0 = <&i2c2_pins>;
466 clock-frequency = <100000>;
468 tlv320aic3x: tlv320aic3x@18 {
469 compatible = "ti,tlv320aic3x";
471 gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
473 0 /* AIC3X_GPIO1_FUNC_DISABLED */
474 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
477 AVDD-supply = <&vmmc2>;
478 DRVDD-supply = <&vmmc2>;
479 IOVDD-supply = <&vio>;
480 DVDD-supply = <&vio>;
483 tlv320aic3x_aux: tlv320aic3x@19 {
484 compatible = "ti,tlv320aic3x";
486 gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
488 AVDD-supply = <&vmmc2>;
489 DRVDD-supply = <&vmmc2>;
490 IOVDD-supply = <&vio>;
491 DVDD-supply = <&vio>;
494 tsl2563: tsl2563@29 {
495 compatible = "amstaos,tsl2563";
498 amstaos,cover-comp-gain = <16>;
502 compatible = "national,lp5523";
504 clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
505 enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
508 chan-name = "lp5523:kb1";
509 led-cur = /bits/ 8 <50>;
510 max-cur = /bits/ 8 <100>;
514 chan-name = "lp5523:kb2";
515 led-cur = /bits/ 8 <50>;
516 max-cur = /bits/ 8 <100>;
520 chan-name = "lp5523:kb3";
521 led-cur = /bits/ 8 <50>;
522 max-cur = /bits/ 8 <100>;
526 chan-name = "lp5523:kb4";
527 led-cur = /bits/ 8 <50>;
528 max-cur = /bits/ 8 <100>;
532 chan-name = "lp5523:b";
533 led-cur = /bits/ 8 <50>;
534 max-cur = /bits/ 8 <100>;
538 chan-name = "lp5523:g";
539 led-cur = /bits/ 8 <50>;
540 max-cur = /bits/ 8 <100>;
544 chan-name = "lp5523:r";
545 led-cur = /bits/ 8 <50>;
546 max-cur = /bits/ 8 <100>;
550 chan-name = "lp5523:kb5";
551 led-cur = /bits/ 8 <50>;
552 max-cur = /bits/ 8 <100>;
556 chan-name = "lp5523:kb6";
557 led-cur = /bits/ 8 <50>;
558 max-cur = /bits/ 8 <100>;
562 bq27200: bq27200@55 {
563 compatible = "ti,bq27200";
567 tpa6130a2: tpa6130a2@60 {
568 compatible = "ti,tpa6130a2";
571 Vdd-supply = <&vmmc2>;
573 power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* 98 */
577 compatible = "silabs,si4713";
580 interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_FALLING>; /* 53 */
581 reset-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 */
583 vdd-supply = <&vaux1>;
586 bq24150a: bq24150a@6b {
587 compatible = "ti,bq24150a";
590 ti,current-limit = <100>;
591 ti,weak-battery-voltage = <3400>;
592 ti,battery-regulation-voltage = <4200>;
593 ti,charge-current = <650>;
594 ti,termination-current = <100>;
595 ti,resistor-sense = <68>;
597 ti,usb-charger-detection = <&isp1704>;
602 pinctrl-names = "default";
603 pinctrl-0 = <&i2c3_pins>;
605 clock-frequency = <400000>;
609 pinctrl-names = "default";
610 pinctrl-0 = <&mmc1_pins>;
611 vmmc-supply = <&vmmc1>;
613 cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */
616 /* most boards use vaux3, only some old versions use vmmc2 instead */
618 pinctrl-names = "default";
619 pinctrl-0 = <&mmc2_pins>;
620 vmmc-supply = <&vaux3>;
621 vmmc_aux-supply = <&vsim>;
631 ranges = <0 0 0x01000000 0x01000000>, /* 16 MB for OneNAND */
632 <1 0 0x02000000 0x01000000>; /* 16 MB for smc91c96 */
633 pinctrl-names = "default";
634 pinctrl-0 = <&gpmc_pins>;
636 /* sys_ndmareq1 could be used by the driver, not as gpio65 though */
638 #address-cells = <1>;
640 reg = <0 0 0x20000>; /* CS0, offset 0, IO size 128K */
644 gpmc,burst-length = <16>;
648 gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */
649 gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */
651 gpmc,cs-rd-off-ns = <87>;
652 gpmc,cs-wr-off-ns = <87>;
653 gpmc,adv-on-ns = <0>;
654 gpmc,adv-rd-off-ns = <10>;
655 gpmc,adv-wr-off-ns = <10>;
656 gpmc,oe-on-ns = <15>;
657 gpmc,oe-off-ns = <87>;
659 gpmc,we-off-ns = <87>;
660 gpmc,rd-cycle-ns = <112>;
661 gpmc,wr-cycle-ns = <112>;
662 gpmc,access-ns = <81>;
663 gpmc,page-burst-access-ns = <15>;
664 gpmc,bus-turnaround-ns = <0>;
665 gpmc,cycle2cycle-delay-ns = <0>;
666 gpmc,wait-monitoring-ns = <0>;
667 gpmc,clk-activation-ns = <5>;
668 gpmc,wr-data-mux-bus-ns = <30>;
669 gpmc,wr-access-ns = <81>;
670 gpmc,sync-clk-ps = <15000>;
673 * MTD partition table corresponding to Nokia's
674 * Maemo 5 (Fremantle) release.
677 label = "bootloader";
678 reg = <0x00000000 0x00020000>;
683 reg = <0x00020000 0x00060000>;
687 reg = <0x00080000 0x00040000>;
691 reg = <0x000c0000 0x00200000>;
695 reg = <0x002c0000 0x00200000>;
699 reg = <0x004c0000 0x0fb40000>;
704 compatible = "smsc,lan91c94";
708 interrupt-parent = <&gpio2>;
709 interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; /* gpio54 */
710 reg = <1 0x300 0xf>; /* 16 byte IO range at offset 0x300 */
712 pinctrl-names = "default";
713 pinctrl-0 = <ðernet_pins>;
714 power-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>; /* gpio86 */
715 reset-gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* gpio164 */
716 gpmc,device-width = <2>;
717 gpmc,sync-clk-ps = <0>;
719 gpmc,cs-rd-off-ns = <48>;
720 gpmc,cs-wr-off-ns = <24>;
721 gpmc,adv-on-ns = <0>;
722 gpmc,adv-rd-off-ns = <0>;
723 gpmc,adv-wr-off-ns = <0>;
724 gpmc,we-on-ns = <12>;
725 gpmc,we-off-ns = <18>;
726 gpmc,oe-on-ns = <12>;
727 gpmc,oe-off-ns = <48>;
728 gpmc,page-burst-access-ns = <0>;
729 gpmc,access-ns = <42>;
730 gpmc,rd-cycle-ns = <180>;
731 gpmc,wr-cycle-ns = <180>;
732 gpmc,bus-turnaround-ns = <0>;
733 gpmc,cycle2cycle-delay-ns = <0>;
734 gpmc,wait-monitoring-ns = <0>;
735 gpmc,clk-activation-ns = <0>;
736 gpmc,wr-access-ns = <0>;
737 gpmc,wr-data-mux-bus-ns = <12>;
743 * For some reason, touchscreen is necessary for screen to work at
744 * all on real hw. It works well without it on emulator.
746 * Also... order in the device tree actually matters here.
749 compatible = "ti,tsc2005";
750 spi-max-frequency = <6000000>;
755 reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */
756 interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */
758 touchscreen-fuzz-x = <4>;
759 touchscreen-fuzz-y = <7>;
760 touchscreen-fuzz-pressure = <2>;
761 touchscreen-max-x = <4096>;
762 touchscreen-max-y = <4096>;
763 touchscreen-max-pressure = <2048>;
765 ti,x-plate-ohms = <280>;
766 ti,esd-recovery-timeout-ms = <8000>;
770 compatible = "sony,acx565akm";
771 spi-max-frequency = <6000000>;
774 pinctrl-names = "default";
775 pinctrl-0 = <&acx565akm_pins>;
778 reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */
782 remote-endpoint = <&sdi_out>;
789 pinctrl-names = "default";
790 pinctrl-0 = <&mcspi4_pins>;
793 pinctrl-names = "default";
794 pinctrl-0 = <&wl1251_pins>;
798 compatible = "ti,wl1251";
800 spi-max-frequency = <48000000>;
805 ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */
807 interrupt-parent = <&gpio2>;
808 interrupts = <10 IRQ_TYPE_NONE>; /* gpio line 42 */
813 interface-type = <0>;
814 usb-phy = <&usb2_phy>;
816 phy-names = "usb2-phy";
826 interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
827 pinctrl-names = "default";
828 pinctrl-0 = <&uart2_pins>;
832 interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
833 pinctrl-names = "default";
834 pinctrl-0 = <&uart3_pins>;
840 pinctrl-names = "default";
841 pinctrl-0 = <&dss_sdi_pins>;
843 vdds_sdi-supply = <&vaux1>;
846 #address-cells = <1>;
853 remote-endpoint = <&lcd_in>;
863 vdda-supply = <&vdac>;
867 remote-endpoint = <&tv_connector_in>;
878 pinctrl-names = "default";
879 pinctrl-0 = <&ssi_pins>;
881 ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */
884 compatible = "nokia,n900-modem";
886 pinctrl-names = "default";
887 pinctrl-0 = <&modem_pins>;
889 hsi-channel-ids = <0>, <1>, <2>, <3>;
890 hsi-channel-names = "mcsaab-control",
894 hsi-speed-kbps = <55000>;
896 hsi-flow = "synchronized";
897 hsi-arb-mode = "round-robin";
899 interrupts-extended = <&gpio3 8 IRQ_TYPE_EDGE_FALLING>; /* 72 */
901 gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>, /* 70 */
902 <&gpio3 9 GPIO_ACTIVE_HIGH>, /* 73 */
903 <&gpio3 10 GPIO_ACTIVE_HIGH>, /* 74 */
904 <&gpio3 11 GPIO_ACTIVE_HIGH>, /* 75 */
905 <&gpio5 29 GPIO_ACTIVE_HIGH>; /* 157 */
906 gpio-names = "cmt_apeslpx",