2 * Copyright (C) 2013 Pavel Machek <pavel@ucw.cz>
3 * Copyright (C) 2013-2014 Aaro Koskinen <aaro.koskinen@iki.fi>
5 * This program is free software; you can redistribute it and/or modify
6 * it under the terms of the GNU General Public License version 2 (or later) as
7 * published by the Free Software Foundation.
12 #include "omap34xx-hs.dtsi"
13 #include <dt-bindings/input/input.h>
17 compatible = "nokia,omap3-n900", "ti,omap3430", "ti,omap3";
26 compatible = "gpio-leds";
28 label = "debug::sleep";
29 gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* gpio162 */
30 linux,default-trigger = "default-on";
31 pinctrl-names = "default";
32 pinctrl-0 = <&debug_leds>;
37 device_type = "memory";
38 reg = <0x80000000 0x10000000>; /* 256 MB */
42 compatible = "gpio-keys";
45 label = "Camera Lens Cover";
46 gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */
47 linux,input-type = <5>; /* EV_SW */
48 linux,code = <0x09>; /* SW_CAMERA_LENS_COVER */
53 label = "Camera Focus";
54 gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */
55 linux,code = <0x210>; /* KEY_CAMERA_FOCUS */
60 label = "Camera Capture";
61 gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */
62 linux,code = <0xd4>; /* KEY_CAMERA */
67 label = "Lock Button";
68 gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */
69 linux,code = <0x98>; /* KEY_SCREENLOCK */
74 label = "Keypad Slide";
75 gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */
76 linux,input-type = <5>; /* EV_SW */
77 linux,code = <0x0a>; /* SW_KEYPAD_SLIDE */
82 label = "Proximity Sensor";
83 gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */
84 linux,input-type = <5>; /* EV_SW */
85 linux,code = <0x0b>; /* SW_FRONT_PROXIMITY */
90 compatible = "nxp,isp1704";
91 nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>;
92 usb-phy = <&usb2_phy>;
96 compatible = "composite-video-connector";
100 tv_connector_in: endpoint {
101 remote-endpoint = <&venc_out>;
107 compatible = "nokia,n900-audio";
109 nokia,cpu-dai = <&mcbsp2>;
110 nokia,audio-codec = <&tlv320aic3x>, <&tlv320aic3x_aux>;
111 nokia,headphone-amplifier = <&tpa6130a2>;
113 tvout-selection-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>; /* 40 */
114 jack-detection-gpios = <&gpio6 17 GPIO_ACTIVE_HIGH>; /* 177 */
115 eci-switch-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* 182 */
116 speaker-amplifier-gpios = <&twl_gpio 7 GPIO_ACTIVE_HIGH>;
121 pinctrl-names = "default";
123 uart2_pins: pinmux_uart2_pins {
124 pinctrl-single,pins = <
125 0x14a (PIN_INPUT | MUX_MODE0) /* uart2_rx */
126 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx */
130 uart3_pins: pinmux_uart3_pins {
131 pinctrl-single,pins = <
132 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx */
133 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx */
137 ethernet_pins: pinmux_ethernet_pins {
138 pinctrl-single,pins = <
139 OMAP3_CORE1_IOPAD(0x20b4, PIN_INPUT_PULLDOWN | MUX_MODE4) /* gpmc_ncs3.gpio_54 */
140 OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE4) /* dss_data16.gpio_86 */
141 OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4) /* uart3_rts_sd.gpio_164 */
145 i2c1_pins: pinmux_i2c1_pins {
146 pinctrl-single,pins = <
147 0x18a (PIN_INPUT | MUX_MODE0) /* i2c1_scl */
148 0x18c (PIN_INPUT | MUX_MODE0) /* i2c1_sda */
152 i2c2_pins: pinmux_i2c2_pins {
153 pinctrl-single,pins = <
154 0x18e (PIN_INPUT | MUX_MODE0) /* i2c2_scl */
155 0x190 (PIN_INPUT | MUX_MODE0) /* i2c2_sda */
159 i2c3_pins: pinmux_i2c3_pins {
160 pinctrl-single,pins = <
161 0x192 (PIN_INPUT | MUX_MODE0) /* i2c3_scl */
162 0x194 (PIN_INPUT | MUX_MODE0) /* i2c3_sda */
166 debug_leds: pinmux_debug_led_pins {
167 pinctrl-single,pins = <
168 OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_clkx.gpio_162 */
172 mcspi4_pins: pinmux_mcspi4_pins {
173 pinctrl-single,pins = <
174 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_clk */
175 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_somi */
176 0x160 (PIN_OUTPUT | MUX_MODE1) /* mcspi4_simo */
177 0x166 (PIN_OUTPUT | MUX_MODE1) /* mcspi4_cs0 */
181 mmc1_pins: pinmux_mmc1_pins {
182 pinctrl-single,pins = <
183 0x114 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */
184 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */
185 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */
186 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */
187 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */
188 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */
192 mmc2_pins: pinmux_mmc2_pins {
193 pinctrl-single,pins = <
194 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */
195 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */
196 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */
197 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */
198 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */
199 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */
200 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat4 */
201 0x136 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat5 */
202 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat6 */
203 0x13a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat7 */
207 acx565akm_pins: pinmux_acx565akm_pins {
208 pinctrl-single,pins = <
209 0x0d4 (PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */
213 dss_sdi_pins: pinmux_dss_sdi_pins {
214 pinctrl-single,pins = <
215 0x0c0 (PIN_OUTPUT | MUX_MODE1) /* dss_data10.sdi_dat1n */
216 0x0c2 (PIN_OUTPUT | MUX_MODE1) /* dss_data11.sdi_dat1p */
217 0x0c4 (PIN_OUTPUT | MUX_MODE1) /* dss_data12.sdi_dat2n */
218 0x0c6 (PIN_OUTPUT | MUX_MODE1) /* dss_data13.sdi_dat2p */
220 0x0d8 (PIN_OUTPUT | MUX_MODE1) /* dss_data22.sdi_clkp */
221 0x0da (PIN_OUTPUT | MUX_MODE1) /* dss_data23.sdi_clkn */
225 wl1251_pins: pinmux_wl1251 {
226 pinctrl-single,pins = <
227 0x0ce (PIN_OUTPUT | MUX_MODE4) /* gpio 87 => wl1251 enable */
228 0x05a (PIN_INPUT | MUX_MODE4) /* gpio 42 => wl1251 irq */
232 ssi_pins: pinmux_ssi {
233 pinctrl-single,pins = <
234 0x150 (PIN_INPUT_PULLUP | MUX_MODE1) /* ssi1_rdy_tx */
235 0x14e (PIN_OUTPUT | MUX_MODE1) /* ssi1_flag_tx */
236 0x152 (PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* ssi1_wake_tx (cawake) */
237 0x14c (PIN_OUTPUT | MUX_MODE1) /* ssi1_dat_tx */
238 0x154 (PIN_INPUT | MUX_MODE1) /* ssi1_dat_rx */
239 0x156 (PIN_INPUT | MUX_MODE1) /* ssi1_flag_rx */
240 0x158 (PIN_OUTPUT | MUX_MODE1) /* ssi1_rdy_rx */
241 0x15a (PIN_OUTPUT | MUX_MODE1) /* ssi1_wake */
245 modem_pins: pinmux_modem {
246 pinctrl-single,pins = <
247 0x0ac (PIN_OUTPUT | MUX_MODE4) /* gpio 70 => cmt_apeslpx */
248 0x0b0 (PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* gpio 72 => ape_rst_rq */
249 0x0b2 (PIN_OUTPUT | MUX_MODE4) /* gpio 73 => cmt_rst_rq */
250 0x0b4 (PIN_OUTPUT | MUX_MODE4) /* gpio 74 => cmt_en */
251 0x0b6 (PIN_OUTPUT | MUX_MODE4) /* gpio 75 => cmt_rst */
252 0x15e (PIN_OUTPUT | MUX_MODE4) /* gpio 157 => cmt_bsi */
258 pinctrl-names = "default";
259 pinctrl-0 = <&i2c1_pins>;
261 clock-frequency = <2200000>;
265 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
266 interrupt-parent = <&intc>;
270 #include "twl4030.dtsi"
271 #include "twl4030_omap3.dtsi"
274 regulator-name = "V28";
275 regulator-min-microvolt = <2800000>;
276 regulator-max-microvolt = <2800000>;
277 regulator-always-on; /* due battery cover sensor */
281 regulator-name = "VCSI";
282 regulator-min-microvolt = <1800000>;
283 regulator-max-microvolt = <1800000>;
287 regulator-name = "VMMC2_30";
288 regulator-min-microvolt = <2800000>;
289 regulator-max-microvolt = <3000000>;
293 regulator-name = "VCAM_ANA_28";
294 regulator-min-microvolt = <2800000>;
295 regulator-max-microvolt = <2800000>;
299 regulator-name = "VMMC1";
300 regulator-min-microvolt = <1850000>;
301 regulator-max-microvolt = <3150000>;
305 regulator-name = "V28_A";
306 regulator-min-microvolt = <2800000>;
307 regulator-max-microvolt = <3000000>;
308 regulator-always-on; /* due VIO leak to AIC34 VDDs */
312 regulator-name = "VPLL";
313 regulator-min-microvolt = <1800000>;
314 regulator-max-microvolt = <1800000>;
319 regulator-name = "VSDI_CSI";
320 regulator-min-microvolt = <1800000>;
321 regulator-max-microvolt = <1800000>;
326 regulator-name = "VMMC2_IO_18";
327 regulator-min-microvolt = <1800000>;
328 regulator-max-microvolt = <1800000>;
332 regulator-name = "VIO";
333 regulator-min-microvolt = <1800000>;
334 regulator-max-microvolt = <1800000>;
339 regulator-name = "VINTANA1";
340 /* fixed to 1500000 */
345 regulator-name = "VINTANA2";
346 regulator-min-microvolt = <2750000>;
347 regulator-max-microvolt = <2750000>;
352 regulator-name = "VINTDIG";
353 /* fixed to 1500000 */
359 compatible = "ti,twl4030-audio";
360 ti,enable-vibra = <1>;
364 compatible = "ti,twl4030-power-n900", "ti,twl4030-power-idle-osc-off";
370 linux,keymap = < MATRIX_KEY(0x00, 0x00, KEY_Q)
371 MATRIX_KEY(0x00, 0x01, KEY_O)
372 MATRIX_KEY(0x00, 0x02, KEY_P)
373 MATRIX_KEY(0x00, 0x03, KEY_COMMA)
374 MATRIX_KEY(0x00, 0x04, KEY_BACKSPACE)
375 MATRIX_KEY(0x00, 0x06, KEY_A)
376 MATRIX_KEY(0x00, 0x07, KEY_S)
378 MATRIX_KEY(0x01, 0x00, KEY_W)
379 MATRIX_KEY(0x01, 0x01, KEY_D)
380 MATRIX_KEY(0x01, 0x02, KEY_F)
381 MATRIX_KEY(0x01, 0x03, KEY_G)
382 MATRIX_KEY(0x01, 0x04, KEY_H)
383 MATRIX_KEY(0x01, 0x05, KEY_J)
384 MATRIX_KEY(0x01, 0x06, KEY_K)
385 MATRIX_KEY(0x01, 0x07, KEY_L)
387 MATRIX_KEY(0x02, 0x00, KEY_E)
388 MATRIX_KEY(0x02, 0x01, KEY_DOT)
389 MATRIX_KEY(0x02, 0x02, KEY_UP)
390 MATRIX_KEY(0x02, 0x03, KEY_ENTER)
391 MATRIX_KEY(0x02, 0x05, KEY_Z)
392 MATRIX_KEY(0x02, 0x06, KEY_X)
393 MATRIX_KEY(0x02, 0x07, KEY_C)
394 MATRIX_KEY(0x02, 0x08, KEY_F9)
396 MATRIX_KEY(0x03, 0x00, KEY_R)
397 MATRIX_KEY(0x03, 0x01, KEY_V)
398 MATRIX_KEY(0x03, 0x02, KEY_B)
399 MATRIX_KEY(0x03, 0x03, KEY_N)
400 MATRIX_KEY(0x03, 0x04, KEY_M)
401 MATRIX_KEY(0x03, 0x05, KEY_SPACE)
402 MATRIX_KEY(0x03, 0x06, KEY_SPACE)
403 MATRIX_KEY(0x03, 0x07, KEY_LEFT)
405 MATRIX_KEY(0x04, 0x00, KEY_T)
406 MATRIX_KEY(0x04, 0x01, KEY_DOWN)
407 MATRIX_KEY(0x04, 0x02, KEY_RIGHT)
408 MATRIX_KEY(0x04, 0x04, KEY_LEFTCTRL)
409 MATRIX_KEY(0x04, 0x05, KEY_RIGHTALT)
410 MATRIX_KEY(0x04, 0x06, KEY_LEFTSHIFT)
411 MATRIX_KEY(0x04, 0x08, KEY_F10)
413 MATRIX_KEY(0x05, 0x00, KEY_Y)
414 MATRIX_KEY(0x05, 0x08, KEY_F11)
416 MATRIX_KEY(0x06, 0x00, KEY_U)
418 MATRIX_KEY(0x07, 0x00, KEY_I)
419 MATRIX_KEY(0x07, 0x01, KEY_F7)
420 MATRIX_KEY(0x07, 0x02, KEY_F8)
426 ti,pulldowns = <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
430 pinctrl-names = "default";
431 pinctrl-0 = <&i2c2_pins>;
433 clock-frequency = <100000>;
435 tlv320aic3x: tlv320aic3x@18 {
436 compatible = "ti,tlv320aic3x";
438 gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
440 0 /* AIC3X_GPIO1_FUNC_DISABLED */
441 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
444 AVDD-supply = <&vmmc2>;
445 DRVDD-supply = <&vmmc2>;
446 IOVDD-supply = <&vio>;
447 DVDD-supply = <&vio>;
450 tlv320aic3x_aux: tlv320aic3x@19 {
451 compatible = "ti,tlv320aic3x";
453 gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
455 AVDD-supply = <&vmmc2>;
456 DRVDD-supply = <&vmmc2>;
457 IOVDD-supply = <&vio>;
458 DVDD-supply = <&vio>;
461 tsl2563: tsl2563@29 {
462 compatible = "amstaos,tsl2563";
465 amstaos,cover-comp-gain = <16>;
469 compatible = "national,lp5523";
471 clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
472 enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
475 chan-name = "lp5523:kb1";
476 led-cur = /bits/ 8 <50>;
477 max-cur = /bits/ 8 <100>;
481 chan-name = "lp5523:kb2";
482 led-cur = /bits/ 8 <50>;
483 max-cur = /bits/ 8 <100>;
487 chan-name = "lp5523:kb3";
488 led-cur = /bits/ 8 <50>;
489 max-cur = /bits/ 8 <100>;
493 chan-name = "lp5523:kb4";
494 led-cur = /bits/ 8 <50>;
495 max-cur = /bits/ 8 <100>;
499 chan-name = "lp5523:b";
500 led-cur = /bits/ 8 <50>;
501 max-cur = /bits/ 8 <100>;
505 chan-name = "lp5523:g";
506 led-cur = /bits/ 8 <50>;
507 max-cur = /bits/ 8 <100>;
511 chan-name = "lp5523:r";
512 led-cur = /bits/ 8 <50>;
513 max-cur = /bits/ 8 <100>;
517 chan-name = "lp5523:kb5";
518 led-cur = /bits/ 8 <50>;
519 max-cur = /bits/ 8 <100>;
523 chan-name = "lp5523:kb6";
524 led-cur = /bits/ 8 <50>;
525 max-cur = /bits/ 8 <100>;
529 bq27200: bq27200@55 {
530 compatible = "ti,bq27200";
534 tpa6130a2: tpa6130a2@60 {
535 compatible = "ti,tpa6130a2";
538 Vdd-supply = <&vmmc2>;
540 power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* 98 */
543 bq24150a: bq24150a@6b {
544 compatible = "ti,bq24150a";
547 ti,current-limit = <100>;
548 ti,weak-battery-voltage = <3400>;
549 ti,battery-regulation-voltage = <4200>;
550 ti,charge-current = <650>;
551 ti,termination-current = <100>;
552 ti,resistor-sense = <68>;
554 ti,usb-charger-detection = <&isp1704>;
559 pinctrl-names = "default";
560 pinctrl-0 = <&i2c3_pins>;
562 clock-frequency = <400000>;
566 pinctrl-names = "default";
567 pinctrl-0 = <&mmc1_pins>;
568 vmmc-supply = <&vmmc1>;
570 cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */
573 /* most boards use vaux3, only some old versions use vmmc2 instead */
575 pinctrl-names = "default";
576 pinctrl-0 = <&mmc2_pins>;
577 vmmc-supply = <&vaux3>;
578 vmmc_aux-supply = <&vsim>;
588 ranges = <0 0 0x04000000 0x10000000>; /* 256MB */
589 ranges = <0 0 0x01000000 0x01000000>, /* 16 MB for OneNAND */
590 <1 0 0x02000000 0x01000000>; /* 16 MB for smc91c96 */
592 /* gpio-irq for dma: 65 */
595 #address-cells = <1>;
597 reg = <0 0 0x10000000>;
601 gpmc,burst-length = <16>;
605 gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */
606 gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */
608 gpmc,cs-rd-off-ns = <87>;
609 gpmc,cs-wr-off-ns = <87>;
610 gpmc,adv-on-ns = <0>;
611 gpmc,adv-rd-off-ns = <10>;
612 gpmc,adv-wr-off-ns = <10>;
613 gpmc,oe-on-ns = <15>;
614 gpmc,oe-off-ns = <87>;
616 gpmc,we-off-ns = <87>;
617 gpmc,rd-cycle-ns = <112>;
618 gpmc,wr-cycle-ns = <112>;
619 gpmc,access-ns = <81>;
620 gpmc,page-burst-access-ns = <15>;
621 gpmc,bus-turnaround-ns = <0>;
622 gpmc,cycle2cycle-delay-ns = <0>;
623 gpmc,wait-monitoring-ns = <0>;
624 gpmc,clk-activation-ns = <5>;
625 gpmc,wr-data-mux-bus-ns = <30>;
626 gpmc,wr-access-ns = <81>;
627 gpmc,sync-clk-ps = <15000>;
630 * MTD partition table corresponding to Nokia's
631 * Maemo 5 (Fremantle) release.
634 label = "bootloader";
635 reg = <0x00000000 0x00020000>;
640 reg = <0x00020000 0x00060000>;
644 reg = <0x00080000 0x00040000>;
648 reg = <0x000c0000 0x00200000>;
652 reg = <0x002c0000 0x00200000>;
656 reg = <0x004c0000 0x0fb40000>;
661 compatible = "smsc,lan91c94";
665 interrupt-parent = <&gpio2>;
666 interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; /* gpio54 */
667 reg = <1 0x300 0xf>; /* 16 byte IO range at offset 0x300 */
669 pinctrl-names = "default";
670 pinctrl-0 = <ðernet_pins>;
671 gpmc,device-width = <2>;
672 gpmc,sync-clk-ps = <0>;
674 gpmc,cs-rd-off-ns = <48>;
675 gpmc,cs-wr-off-ns = <24>;
676 gpmc,adv-on-ns = <0>;
677 gpmc,adv-rd-off-ns = <0>;
678 gpmc,adv-wr-off-ns = <0>;
679 gpmc,we-on-ns = <12>;
680 gpmc,we-off-ns = <18>;
681 gpmc,oe-on-ns = <12>;
682 gpmc,oe-off-ns = <48>;
683 gpmc,page-burst-access-ns = <0>;
684 gpmc,access-ns = <42>;
685 gpmc,rd-cycle-ns = <180>;
686 gpmc,wr-cycle-ns = <180>;
687 gpmc,bus-turnaround-ns = <0>;
688 gpmc,cycle2cycle-delay-ns = <0>;
689 gpmc,wait-monitoring-ns = <0>;
690 gpmc,clk-activation-ns = <0>;
691 gpmc,wr-access-ns = <0>;
692 gpmc,wr-data-mux-bus-ns = <12>;
698 * For some reason, touchscreen is necessary for screen to work at
699 * all on real hw. It works well without it on emulator.
701 * Also... order in the device tree actually matters here.
704 compatible = "ti,tsc2005";
705 spi-max-frequency = <6000000>;
710 reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */
711 interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */
713 touchscreen-fuzz-x = <4>;
714 touchscreen-fuzz-y = <7>;
715 touchscreen-fuzz-pressure = <2>;
716 touchscreen-max-x = <4096>;
717 touchscreen-max-y = <4096>;
718 touchscreen-max-pressure = <2048>;
720 ti,x-plate-ohms = <280>;
721 ti,esd-recovery-timeout-ms = <8000>;
725 compatible = "sony,acx565akm";
726 spi-max-frequency = <6000000>;
729 pinctrl-names = "default";
730 pinctrl-0 = <&acx565akm_pins>;
733 reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */
737 remote-endpoint = <&sdi_out>;
744 pinctrl-names = "default";
745 pinctrl-0 = <&mcspi4_pins>;
748 pinctrl-names = "default";
749 pinctrl-0 = <&wl1251_pins>;
753 compatible = "ti,wl1251";
755 spi-max-frequency = <48000000>;
760 ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */
762 interrupt-parent = <&gpio2>;
763 interrupts = <10 IRQ_TYPE_NONE>; /* gpio line 42 */
768 interface-type = <0>;
769 usb-phy = <&usb2_phy>;
771 phy-names = "usb2-phy";
781 interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
782 pinctrl-names = "default";
783 pinctrl-0 = <&uart2_pins>;
787 interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
788 pinctrl-names = "default";
789 pinctrl-0 = <&uart3_pins>;
795 pinctrl-names = "default";
796 pinctrl-0 = <&dss_sdi_pins>;
798 vdds_sdi-supply = <&vaux1>;
801 #address-cells = <1>;
808 remote-endpoint = <&lcd_in>;
818 vdda-supply = <&vdac>;
822 remote-endpoint = <&tv_connector_in>;
833 pinctrl-names = "default";
834 pinctrl-0 = <&ssi_pins>;
836 ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */
839 compatible = "nokia,n900-modem";
841 pinctrl-names = "default";
842 pinctrl-0 = <&modem_pins>;
844 hsi-channel-ids = <0>, <1>, <2>, <3>;
845 hsi-channel-names = "mcsaab-control",
849 hsi-speed-kbps = <55000>;
851 hsi-flow = "synchronized";
852 hsi-arb-mode = "round-robin";
854 interrupts-extended = <&gpio3 8 IRQ_TYPE_EDGE_FALLING>; /* 72 */
856 gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>, /* 70 */
857 <&gpio3 9 GPIO_ACTIVE_HIGH>, /* 73 */
858 <&gpio3 10 GPIO_ACTIVE_HIGH>, /* 74 */
859 <&gpio3 11 GPIO_ACTIVE_HIGH>, /* 75 */
860 <&gpio5 29 GPIO_ACTIVE_HIGH>; /* 157 */
861 gpio-names = "cmt_apeslpx",