2 * Copyright (C) 2011-2013 Texas Instruments Incorporated - http://www.ti.com/
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
8 #include "elpida_ecb240abacn.dtsi"
11 model = "TI OMAP4 PandaBoard";
12 compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4";
15 device_type = "memory";
16 reg = <0x80000000 0x40000000>; /* 1 GB */
20 compatible = "gpio-leds";
21 pinctrl-names = "default";
27 label = "pandaboard::status1";
28 gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
29 linux,default-trigger = "heartbeat";
33 label = "pandaboard::status2";
34 gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
35 linux,default-trigger = "mmc0";
40 compatible = "ti,abe-twl6040";
41 ti,model = "PandaBoard";
43 ti,mclk-freq = <38400000>;
47 ti,twl6040 = <&twl6040>;
51 "Headset Stereophone", "HSOL",
52 "Headset Stereophone", "HSOR",
57 "HSMIC", "Headset Mic",
58 "Headset Mic", "Headset Mic Bias",
64 * Temp hack: Need to be replaced with the proper gpio-controlled
65 * reset driver as soon it will be merged.
66 * http://thread.gmane.org/gmane.linux.drivers.devicetree/36830
68 /* HS USB Port 1 RESET */
69 hsusb1_reset: hsusb1_reset_reg {
70 compatible = "regulator-fixed";
71 regulator-name = "hsusb1_reset";
72 regulator-min-microvolt = <3300000>;
73 regulator-max-microvolt = <3300000>;
74 gpio = <&gpio2 30 0>; /* gpio_62 */
75 startup-delay-us = <70000>;
79 /* HS USB Port 1 Power */
80 hsusb1_power: hsusb1_power_reg {
81 compatible = "regulator-fixed";
82 regulator-name = "hsusb1_vbus";
83 regulator-min-microvolt = <3300000>;
84 regulator-max-microvolt = <3300000>;
85 gpio = <&gpio1 1 0>; /* gpio_1 */
86 startup-delay-us = <70000>;
89 * boot-on is required along with always-on as the
90 * regulator framework doesn't enable the regulator
91 * if boot-on is not there.
97 /* HS USB Host PHY on PORT 1 */
98 hsusb1_phy: hsusb1_phy {
99 compatible = "usb-nop-xceiv";
100 reset-supply = <&hsusb1_reset>;
101 vcc-supply = <&hsusb1_power>;
104 * put the right clock phandle here when available
105 * clocks = <&auxclk3>;
106 * clock-names = "main_clk";
108 clock-frequency = <19200000>;
113 pinctrl-names = "default";
118 twl6030_wkup_pins: pinmux_twl6030_wkup_pins {
119 pinctrl-single,pins = <
120 0x14 (PIN_OUTPUT | MUX_MODE2) /* fref_clk0_out.sys_drm_msecure */
126 pinctrl-names = "default";
137 twl6030_pins: pinmux_twl6030_pins {
138 pinctrl-single,pins = <
139 0x15e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1.sys_nirq1 */
143 twl6040_pins: pinmux_twl6040_pins {
144 pinctrl-single,pins = <
145 0xe0 (PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */
146 0x160 (PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */
150 mcpdm_pins: pinmux_mcpdm_pins {
151 pinctrl-single,pins = <
152 0xc6 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */
153 0xc8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */
154 0xca (PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */
155 0xcc (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */
156 0xce (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
160 mcbsp1_pins: pinmux_mcbsp1_pins {
161 pinctrl-single,pins = <
162 0xbe (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */
163 0xc0 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */
164 0xc2 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */
165 0xc4 (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */
169 dss_hdmi_pins: pinmux_dss_hdmi_pins {
170 pinctrl-single,pins = <
171 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
172 0x5c (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
173 0x5e (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
177 tpd12s015_pins: pinmux_tpd12s015_pins {
178 pinctrl-single,pins = <
179 0x22 (PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */
180 0x48 (PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */
181 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */
185 hsusbb1_pins: pinmux_hsusbb1_pins {
186 pinctrl-single,pins = <
187 0x82 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */
188 0x84 (PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
189 0x86 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */
190 0x88 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */
191 0x8a (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */
192 0x8c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */
193 0x8e (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */
194 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */
195 0x92 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */
196 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */
197 0x96 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */
198 0x98 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */
202 i2c1_pins: pinmux_i2c1_pins {
203 pinctrl-single,pins = <
204 0xe2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
205 0xe4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
209 i2c2_pins: pinmux_i2c2_pins {
210 pinctrl-single,pins = <
211 0xe6 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */
212 0xe8 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */
216 i2c3_pins: pinmux_i2c3_pins {
217 pinctrl-single,pins = <
218 0xea (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
219 0xec (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
223 i2c4_pins: pinmux_i2c4_pins {
224 pinctrl-single,pins = <
225 0xee (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
226 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
232 led_wkgpio_pins: pinmux_leds_wkpins {
233 pinctrl-single,pins = <
234 0x1a (PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */
235 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */
241 pinctrl-names = "default";
242 pinctrl-0 = <&i2c1_pins>;
244 clock-frequency = <400000>;
249 interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
250 interrupt-parent = <&gic>;
254 compatible = "ti,twl6040";
257 interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
258 interrupt-parent = <&gic>;
259 ti,audpwron-gpio = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio line 127 */
261 vio-supply = <&v1v8>;
262 v2v1-supply = <&v2v1>;
267 #include "twl6030.dtsi"
270 pinctrl-names = "default";
271 pinctrl-0 = <&i2c2_pins>;
273 clock-frequency = <400000>;
277 pinctrl-names = "default";
278 pinctrl-0 = <&i2c3_pins>;
280 clock-frequency = <100000>;
283 * Display monitor features are burnt in their EEPROM as EDID data.
284 * The EEPROM is connected as I2C slave device.
287 compatible = "ti,eeprom";
293 pinctrl-names = "default";
294 pinctrl-0 = <&i2c4_pins>;
296 clock-frequency = <400000>;
300 vmmc-supply = <&vmmc>;
323 device-handle = <&elpida_ECB240ABACN>;
328 device-handle = <&elpida_ECB240ABACN>;
343 &twl_usb_comparator {
344 usb-supply = <&vusb>;
348 interface-type = <1>;
354 port1-mode = "ehci-phy";
358 phys = <&hsusb1_phy>;