2 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
11 #include <dt-bindings/interrupt-controller/irq.h>
12 #include <dt-bindings/interrupt-controller/arm-gic.h>
15 model = "TI OMAP5 uEVM board";
16 compatible = "ti,omap5-uevm", "ti,omap5";
19 device_type = "memory";
20 reg = <0x80000000 0x7F000000>; /* 2032 MB */
23 vmmcsd_fixed: fixedregulator-mmcsd {
24 compatible = "regulator-fixed";
25 regulator-name = "vmmcsd_fixed";
26 regulator-min-microvolt = <3000000>;
27 regulator-max-microvolt = <3000000>;
30 /* HS USB Port 2 RESET */
31 hsusb2_reset: hsusb2_reset_reg {
32 compatible = "regulator-fixed";
33 regulator-name = "hsusb2_reset";
34 regulator-min-microvolt = <3300000>;
35 regulator-max-microvolt = <3300000>;
36 gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 HUB_NRESET */
37 startup-delay-us = <70000>;
41 /* HS USB Host PHY on PORT 2 */
42 hsusb2_phy: hsusb2_phy {
43 compatible = "usb-nop-xceiv";
44 reset-supply = <&hsusb2_reset>;
47 * Put the right clock phandle here when available
48 * clocks = <&auxclk1>;
49 * clock-names = "main_clk";
51 clock-frequency = <19200000>;
54 /* HS USB Port 3 RESET */
55 hsusb3_reset: hsusb3_reset_reg {
56 compatible = "regulator-fixed";
57 regulator-name = "hsusb3_reset";
58 regulator-min-microvolt = <3300000>;
59 regulator-max-microvolt = <3300000>;
60 gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>; /* gpio3_79 ETH_NRESET */
61 startup-delay-us = <70000>;
65 /* HS USB Host PHY on PORT 3 */
66 hsusb3_phy: hsusb3_phy {
67 compatible = "usb-nop-xceiv";
68 reset-supply = <&hsusb3_reset>;
72 compatible = "gpio-leds";
74 label = "omap5:blue:usr1";
75 gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
76 linux,default-trigger = "heartbeat";
77 default-state = "off";
83 pinctrl-names = "default";
94 twl6040_pins: pinmux_twl6040_pins {
95 pinctrl-single,pins = <
96 0x18a (PIN_OUTPUT | MUX_MODE6) /* perslimbus2_clock.gpio5_145 */
100 mcpdm_pins: pinmux_mcpdm_pins {
101 pinctrl-single,pins = <
102 0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
103 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */
104 0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */
105 0x160 (PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */
106 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */
110 dmic_pins: pinmux_dmic_pins {
111 pinctrl-single,pins = <
112 0x144 (PIN_INPUT | MUX_MODE0) /* abedmic_din1.abedmic_din1 */
113 0x146 (PIN_INPUT | MUX_MODE0) /* abedmic_din2.abedmic_din2 */
114 0x148 (PIN_INPUT | MUX_MODE0) /* abedmic_din3.abedmic_din3 */
115 0x14a (PIN_OUTPUT | MUX_MODE0) /* abedmic_clk1.abedmic_clk1 */
119 mcbsp1_pins: pinmux_mcbsp1_pins {
120 pinctrl-single,pins = <
121 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */
122 0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */
123 0x150 (PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */
124 0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */
128 mcbsp2_pins: pinmux_mcbsp2_pins {
129 pinctrl-single,pins = <
130 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */
131 0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */
132 0x158 (PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */
133 0x15a (PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */
137 i2c1_pins: pinmux_i2c1_pins {
138 pinctrl-single,pins = <
139 0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
140 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
144 i2c5_pins: pinmux_i2c5_pins {
145 pinctrl-single,pins = <
146 0x184 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */
147 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */
151 mcspi2_pins: pinmux_mcspi2_pins {
152 pinctrl-single,pins = <
153 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
154 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
155 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */
156 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs */
160 mcspi3_pins: pinmux_mcspi3_pins {
161 pinctrl-single,pins = <
162 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */
163 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */
164 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */
165 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */
169 mcspi4_pins: pinmux_mcspi4_pins {
170 pinctrl-single,pins = <
171 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */
172 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */
173 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */
174 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */
178 usbhost_pins: pinmux_usbhost_pins {
179 pinctrl-single,pins = <
180 0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
181 0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
183 0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
184 0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
186 0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */
187 0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */
191 led_gpio_pins: pinmux_led_gpio_pins {
192 pinctrl-single,pins = <
193 0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */
197 uart1_pins: pinmux_uart1_pins {
198 pinctrl-single,pins = <
199 0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */
200 0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */
201 0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */
202 0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */
206 uart3_pins: pinmux_uart3_pins {
207 pinctrl-single,pins = <
208 0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */
209 0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */
213 uart5_pins: pinmux_uart5_pins {
214 pinctrl-single,pins = <
215 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */
216 0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */
217 0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */
218 0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */
225 pinctrl-names = "default";
230 usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
231 pinctrl-single,pins = <
232 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
238 vmmc-supply = <&ldo9_reg>;
243 vmmc-supply = <&vmmcsd_fixed>;
262 pinctrl-names = "default";
263 pinctrl-0 = <&i2c1_pins>;
265 clock-frequency = <400000>;
268 compatible = "ti,palmas";
269 interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
270 interrupt-parent = <&gic>;
272 interrupt-controller;
273 #interrupt-cells = <2>;
276 compatible = "ti,palmas-pmic";
277 interrupt-parent = <&palmas>;
278 interrupts = <14 IRQ_TYPE_NONE>;
279 interrupt-name = "short-irq";
284 smps123_reg: smps123 {
286 regulator-name = "smps123";
287 regulator-min-microvolt = < 600000>;
288 regulator-max-microvolt = <1500000>;
295 regulator-name = "smps45";
296 regulator-min-microvolt = < 600000>;
297 regulator-max-microvolt = <1310000>;
303 /* VDD_DDR3 - over VDD_SMPS6 */
304 regulator-name = "smps6";
305 regulator-min-microvolt = <1200000>;
306 regulator-max-microvolt = <1200000>;
312 /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
313 regulator-name = "smps7";
314 regulator-min-microvolt = <1800000>;
315 regulator-max-microvolt = <1800000>;
322 regulator-name = "smps8";
323 regulator-min-microvolt = < 600000>;
324 regulator-max-microvolt = <1310000>;
330 /* VDDA_2v1_AUD over VDD_2v1 */
331 regulator-name = "smps9";
332 regulator-min-microvolt = <2100000>;
333 regulator-max-microvolt = <2100000>;
334 ti,smps-range = <0x80>;
339 regulator-name = "smps10";
340 regulator-min-microvolt = <5000000>;
341 regulator-max-microvolt = <5000000>;
347 /* VDDAPHY_CAM: vdda_csiport */
348 regulator-name = "ldo1";
349 regulator-min-microvolt = <1500000>;
350 regulator-max-microvolt = <1800000>;
354 /* VCC_2V8_DISP: Does not go anywhere */
355 regulator-name = "ldo2";
356 regulator-min-microvolt = <2800000>;
357 regulator-max-microvolt = <2800000>;
363 /* VDDAPHY_MDM: vdda_lli */
364 regulator-name = "ldo3";
365 regulator-min-microvolt = <1500000>;
366 regulator-max-microvolt = <1500000>;
368 /* Only if Modem is used */
373 /* VDDAPHY_DISP: vdda_dsiport/hdmi */
374 regulator-name = "ldo4";
375 regulator-min-microvolt = <1500000>;
376 regulator-max-microvolt = <1800000>;
380 /* VDDA_1V8_PHY: usb/sata/hdmi.. */
381 regulator-name = "ldo5";
382 regulator-min-microvolt = <1800000>;
383 regulator-max-microvolt = <1800000>;
389 /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
390 regulator-name = "ldo6";
391 regulator-min-microvolt = <1200000>;
392 regulator-max-microvolt = <1200000>;
399 regulator-name = "ldo7";
400 regulator-min-microvolt = <2000000>;
401 regulator-max-microvolt = <2000000>;
402 /* Only for efuse reprograming! */
407 /* VDD_3v0: Does not go anywhere */
408 regulator-name = "ldo8";
409 regulator-min-microvolt = <3000000>;
410 regulator-max-microvolt = <3000000>;
417 /* VCC_DV_SDIO: vdds_sdcard */
418 regulator-name = "ldo9";
419 regulator-min-microvolt = <1800000>;
420 regulator-max-microvolt = <3000000>;
425 /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
426 regulator-name = "ldoln";
427 regulator-min-microvolt = <1800000>;
428 regulator-max-microvolt = <1800000>;
434 /* VDDA_3V_USB: VDDA_USBHS33 */
435 regulator-name = "ldousb";
436 regulator-min-microvolt = <3250000>;
437 regulator-max-microvolt = <3250000>;
443 /* REGEN3 controls LDO9 supply to card */
444 regulator-name = "regen3";
454 pinctrl-names = "default";
455 pinctrl-0 = <&i2c5_pins>;
457 clock-frequency = <400000>;
465 port2-mode = "ehci-hsic";
466 port3-mode = "ehci-hsic";
470 phys = <0 &hsusb2_phy &hsusb3_phy>;
478 pinctrl-names = "default";
479 pinctrl-0 = <&mcspi2_pins>;
483 pinctrl-names = "default";
484 pinctrl-0 = <&mcspi3_pins>;
488 pinctrl-names = "default";
489 pinctrl-0 = <&mcspi4_pins>;
493 pinctrl-names = "default";
494 pinctrl-0 = <&uart1_pins>;
498 pinctrl-names = "default";
499 pinctrl-0 = <&uart3_pins>;
503 pinctrl-names = "default";
504 pinctrl-0 = <&uart5_pins>;