2 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
11 #include <dt-bindings/interrupt-controller/irq.h>
12 #include <dt-bindings/interrupt-controller/arm-gic.h>
15 model = "TI OMAP5 uEVM board";
16 compatible = "ti,omap5-uevm", "ti,omap5";
19 device_type = "memory";
20 reg = <0x80000000 0x7F000000>; /* 2032 MB */
23 vmmcsd_fixed: fixedregulator-mmcsd {
24 compatible = "regulator-fixed";
25 regulator-name = "vmmcsd_fixed";
26 regulator-min-microvolt = <3000000>;
27 regulator-max-microvolt = <3000000>;
30 /* HS USB Host PHY on PORT 2 */
31 hsusb2_phy: hsusb2_phy {
32 compatible = "usb-nop-xceiv";
33 reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
36 * Put the right clock phandle here when available
37 * clocks = <&auxclk1>;
38 * clock-names = "main_clk";
40 clock-frequency = <19200000>;
43 /* HS USB Host PHY on PORT 3 */
44 hsusb3_phy: hsusb3_phy {
45 compatible = "usb-nop-xceiv";
46 reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
50 compatible = "gpio-leds";
52 label = "omap5:blue:usr1";
53 gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
54 linux,default-trigger = "heartbeat";
55 default-state = "off";
61 pinctrl-names = "default";
71 twl6040_pins: pinmux_twl6040_pins {
72 pinctrl-single,pins = <
73 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */
77 mcpdm_pins: pinmux_mcpdm_pins {
78 pinctrl-single,pins = <
79 0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
80 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */
81 0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */
82 0x160 (PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */
83 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */
87 mcbsp1_pins: pinmux_mcbsp1_pins {
88 pinctrl-single,pins = <
89 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */
90 0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */
91 0x150 (PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */
92 0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */
96 mcbsp2_pins: pinmux_mcbsp2_pins {
97 pinctrl-single,pins = <
98 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */
99 0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */
100 0x158 (PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */
101 0x15a (PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */
105 i2c1_pins: pinmux_i2c1_pins {
106 pinctrl-single,pins = <
107 0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
108 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
112 i2c5_pins: pinmux_i2c5_pins {
113 pinctrl-single,pins = <
114 0x184 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */
115 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */
119 mcspi2_pins: pinmux_mcspi2_pins {
120 pinctrl-single,pins = <
121 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
122 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
123 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */
124 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */
128 mcspi3_pins: pinmux_mcspi3_pins {
129 pinctrl-single,pins = <
130 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */
131 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */
132 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */
133 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */
137 mcspi4_pins: pinmux_mcspi4_pins {
138 pinctrl-single,pins = <
139 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi4_clk */
140 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi4_simo */
141 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi4_somi */
142 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi4_cs0 */
146 usbhost_pins: pinmux_usbhost_pins {
147 pinctrl-single,pins = <
148 0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
149 0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
151 0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
152 0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
154 0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */
155 0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */
159 led_gpio_pins: pinmux_led_gpio_pins {
160 pinctrl-single,pins = <
161 0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */
165 uart1_pins: pinmux_uart1_pins {
166 pinctrl-single,pins = <
167 0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */
168 0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */
169 0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */
170 0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */
174 uart3_pins: pinmux_uart3_pins {
175 pinctrl-single,pins = <
176 0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */
177 0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */
181 uart5_pins: pinmux_uart5_pins {
182 pinctrl-single,pins = <
183 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */
184 0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */
185 0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */
186 0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */
193 pinctrl-names = "default";
198 usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
199 pinctrl-single,pins = <
200 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
206 vmmc-supply = <&ldo9_reg>;
211 vmmc-supply = <&vmmcsd_fixed>;
230 pinctrl-names = "default";
231 pinctrl-0 = <&i2c1_pins>;
233 clock-frequency = <400000>;
236 compatible = "ti,palmas";
237 interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
238 interrupt-parent = <&gic>;
240 interrupt-controller;
241 #interrupt-cells = <2>;
242 ti,system-power-controller;
244 extcon_usb3: palmas_usb {
245 compatible = "ti,palmas-usb-vid";
246 ti,enable-vbus-detection;
247 ti,enable-id-detection;
252 compatible = "ti,palmas-pmic";
253 interrupt-parent = <&palmas>;
254 interrupts = <14 IRQ_TYPE_NONE>;
255 interrupt-name = "short-irq";
260 smps123_reg: smps123 {
262 regulator-name = "smps123";
263 regulator-min-microvolt = < 600000>;
264 regulator-max-microvolt = <1500000>;
271 regulator-name = "smps45";
272 regulator-min-microvolt = < 600000>;
273 regulator-max-microvolt = <1310000>;
279 /* VDD_DDR3 - over VDD_SMPS6 */
280 regulator-name = "smps6";
281 regulator-min-microvolt = <1200000>;
282 regulator-max-microvolt = <1200000>;
288 /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
289 regulator-name = "smps7";
290 regulator-min-microvolt = <1800000>;
291 regulator-max-microvolt = <1800000>;
298 regulator-name = "smps8";
299 regulator-min-microvolt = < 600000>;
300 regulator-max-microvolt = <1310000>;
306 /* VDDA_2v1_AUD over VDD_2v1 */
307 regulator-name = "smps9";
308 regulator-min-microvolt = <2100000>;
309 regulator-max-microvolt = <2100000>;
310 ti,smps-range = <0x80>;
313 smps10_out2_reg: smps10_out2 {
315 regulator-name = "smps10_out2";
316 regulator-min-microvolt = <5000000>;
317 regulator-max-microvolt = <5000000>;
322 smps10_out1_reg: smps10_out1 {
324 regulator-name = "smps10_out1";
325 regulator-min-microvolt = <5000000>;
326 regulator-max-microvolt = <5000000>;
330 /* VDDAPHY_CAM: vdda_csiport */
331 regulator-name = "ldo1";
332 regulator-min-microvolt = <1500000>;
333 regulator-max-microvolt = <1800000>;
337 /* VCC_2V8_DISP: Does not go anywhere */
338 regulator-name = "ldo2";
339 regulator-min-microvolt = <2800000>;
340 regulator-max-microvolt = <2800000>;
346 /* VDDAPHY_MDM: vdda_lli */
347 regulator-name = "ldo3";
348 regulator-min-microvolt = <1500000>;
349 regulator-max-microvolt = <1500000>;
351 /* Only if Modem is used */
356 /* VDDAPHY_DISP: vdda_dsiport/hdmi */
357 regulator-name = "ldo4";
358 regulator-min-microvolt = <1500000>;
359 regulator-max-microvolt = <1800000>;
363 /* VDDA_1V8_PHY: usb/sata/hdmi.. */
364 regulator-name = "ldo5";
365 regulator-min-microvolt = <1800000>;
366 regulator-max-microvolt = <1800000>;
372 /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
373 regulator-name = "ldo6";
374 regulator-min-microvolt = <1200000>;
375 regulator-max-microvolt = <1200000>;
382 regulator-name = "ldo7";
383 regulator-min-microvolt = <2000000>;
384 regulator-max-microvolt = <2000000>;
385 /* Only for efuse reprograming! */
390 /* VDD_3v0: Does not go anywhere */
391 regulator-name = "ldo8";
392 regulator-min-microvolt = <3000000>;
393 regulator-max-microvolt = <3000000>;
400 /* VCC_DV_SDIO: vdds_sdcard */
401 regulator-name = "ldo9";
402 regulator-min-microvolt = <1800000>;
403 regulator-max-microvolt = <3000000>;
408 /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
409 regulator-name = "ldoln";
410 regulator-min-microvolt = <1800000>;
411 regulator-max-microvolt = <1800000>;
417 /* VDDA_3V_USB: VDDA_USBHS33 */
418 regulator-name = "ldousb";
419 regulator-min-microvolt = <3250000>;
420 regulator-max-microvolt = <3250000>;
426 /* REGEN3 controls LDO9 supply to card */
427 regulator-name = "regen3";
437 pinctrl-names = "default";
438 pinctrl-0 = <&i2c5_pins>;
440 clock-frequency = <400000>;
448 port2-mode = "ehci-hsic";
449 port3-mode = "ehci-hsic";
453 phys = <0 &hsusb2_phy &hsusb3_phy>;
457 extcon = <&extcon_usb3>;
458 vbus-supply = <&smps10_out1_reg>;
466 pinctrl-names = "default";
467 pinctrl-0 = <&mcspi2_pins>;
471 pinctrl-names = "default";
472 pinctrl-0 = <&mcspi3_pins>;
476 pinctrl-names = "default";
477 pinctrl-0 = <&mcspi4_pins>;
481 pinctrl-names = "default";
482 pinctrl-0 = <&uart1_pins>;
486 pinctrl-names = "default";
487 pinctrl-0 = <&uart3_pins>;
491 pinctrl-names = "default";
492 pinctrl-0 = <&uart5_pins>;
496 cpu0-supply = <&smps123_reg>;