4 #include "rk3036-pinctrl.dtsi"
12 compatible = "rockchip_pwm_regulator";
13 pwms = <&pwm2 0 25000>;
15 rockchip,pwm_voltage_map= <950000 975000 1000000 1025000 1050000 1075000 1100000 1125000 1150000 1175000 1200000 1225000 1250000 1275000 1300000 1325000 1350000 1375000 1400000 1425000 1450000>;
16 rockchip,pwm_voltage= <1250000>;
17 rockchip,pwm_min_voltage= <950000>;
18 rockchip,pwm_max_voltage= <1450000>;
19 rockchip,pwm_suspend_voltage= <1250000>;
20 rockchip,pwm_coefficient= <500>;
25 pwm_reg0: regulator@0 {
26 regulator-compatible = "pwm_dcdc1";
27 regulator-name= "vdd_arm";
28 regulator-min-microvolt = <950000>;
29 regulator-max-microvolt = <1450000>;
37 compatible = "wlan-platdata";
40 sdio_vref = <1800>; //1800mv or 3300mv
43 //power_pmu_regulator = "act_ldo3";
44 //power_pmu_enable_level = <1>; //1->HIGH, 0->LOW
47 //vref_ctrl_gpio = <&gpio0 GPIO_A2 GPIO_ACTIVE_HIGH>;
48 //vref_pmu_regulator = "act_ldo3";
49 //vref_pmu_enable_level = <1>; //1->HIGH, 0->LOW
51 //WIFI,poweren_gpio = <&gpio4 GPIO_D4 GPIO_ACTIVE_HIGH>;
52 //WIFI,host_wake_irq = <&gpio4 GPIO_D6 GPIO_ACTIVE_HIGH>;
53 //WIFI,reset_gpio = <&gpio0 GPIO_A2 GPIO_ACTIVE_LOW>;
59 compatible = "bluetooth-platdata";
61 //wifi-bt-power-toggle;
63 //uart_rts_gpios = <&gpio4 GPIO_C3 GPIO_ACTIVE_LOW>;
64 //pinctrl-names = "default","rts_gpio";
65 //pinctrl-0 = <&uart0_rts>;
66 //pinctrl-1 = <&uart0_rts_gpio>;
68 //BT,power_gpio = <&gpio4 GPIO_D3 GPIO_ACTIVE_HIGH>;
69 //BT,reset_gpio = <&gpio4 GPIO_D5 GPIO_ACTIVE_HIGH>;
70 //BT,wake_gpio = <&gpio4 GPIO_D2 GPIO_ACTIVE_HIGH>;
71 //BT,wake_host_irq = <&gpio4 GPIO_D7 GPIO_ACTIVE_LOW>;
79 status = "disabled"; // used nand set "disabled" ,used emmc set "okay"
83 clock-frequency = <100000000>;
84 clock-freq-min-max = <400000 100000000>;
90 //supports-DDR_MODE; //you should set the two value in your project. only close in RK3288-SDK board.
94 keep-power-in-suspend;
101 clock-frequency = <50000000>;
102 clock-freq-min-max = <400000 50000000>;
106 card-detect-delay = <200>;
109 keep-power-in-suspend;
111 //vmmc-supply = <&rk808_ldo5_reg>;
116 clock-frequency = <50000000>;
117 clock-freq-min-max = <200000 50000000>;
121 keep-power-in-suspend;
128 dma-names = "!tx", "!rx";
129 //pinctrl-0 = <&uart0_xfer &uart0_cts>;
135 compatible = "rtc,hym8563";
137 //irq_gpio = <&gpio0 GPIO_A4 IRQ_TYPE_EDGE_FALLING>;