3 #include <dt-bindings/interrupt-controller/arm-gic.h>
4 #include <dt-bindings/rkfb/rk_fb.h>
6 #include "../../../arm/boot/dts/vtl_ts_sdk8846.dtsi"
7 //#include "../../../arm/boot/dts/lcd-b101ew05.dtsi"
8 #include "../../../arm/boot/dts/lcd-tv080wum-mipi.dtsi"
9 #include "rk3368-cif-sensor.dtsi"
10 #include <dt-bindings/suspend/rockchip-rk3368.h>
14 bootargs = "earlyprintk=uart8250-32bit,0xff690000";
18 compatible = "wlan-platdata";
19 rockchip,grf = <&grf>;
21 /* wifi_chip_type - wifi chip define
22 * ap6210, ap6330, ap6335
23 * rtl8188eu, rtl8723bs, rtl8723bu
26 wifi_chip_type = "ap6335";
28 sdio_vref = <1800>; //1800mv or 3300mv
33 power_pmu_regulator = "act_ldo3";
34 power_pmu_enable_level = <1>; //1->HIGH, 0->LOW
37 //vref_ctrl_gpio = <&gpio0 GPIO_A2 GPIO_ACTIVE_HIGH>;
38 vref_pmu_regulator = "act_ldo3";
39 vref_pmu_enable_level = <1>; //1->HIGH, 0->LOW
41 WIFI,poweren_gpio = <&gpio3 GPIO_A4 GPIO_ACTIVE_HIGH>;
42 WIFI,host_wake_irq = <&gpio3 GPIO_A6 GPIO_ACTIVE_HIGH>;
43 //WIFI,reset_gpio = <&gpio0 GPIO_A2 GPIO_ACTIVE_LOW>;
49 compatible = "bluetooth-platdata";
51 //wifi-bt-power-toggle;
53 uart_rts_gpios = <&gpio2 GPIO_D3 GPIO_ACTIVE_LOW>;
54 pinctrl-names = "default","rts_gpio";
55 pinctrl-0 = <&uart0_rts>;
56 pinctrl-1 = <&uart0_rts_gpio>;
58 BT,power_gpio = <&gpio3 GPIO_A3 GPIO_ACTIVE_HIGH>;
59 BT,reset_gpio = <&gpio3 GPIO_A5 GPIO_ACTIVE_HIGH>;
60 BT,wake_gpio = <&gpio3 GPIO_A2 GPIO_ACTIVE_HIGH>;
61 BT,wake_host_irq = <&gpio3 GPIO_A7 GPIO_ACTIVE_HIGH>;
67 compatible = "hall_och165t";
68 type = <SENSOR_TYPE_HALL>;
69 irq-gpio = <&gpio0 GPIO_C0 IRQ_TYPE_EDGE_BOTH>;
72 backlight: backlight {
73 compatible = "pwm-backlight";
74 pwms = <&pwm0 0 25000>;
75 brightness-levels = <255 254 253 252 251 250 249 248 247 246 245 244 243 242 241 240
76 239 238 237 236 235 234 233 232 231 230 229 228 227 226 225 224 223 222 221 220
77 219 218 217 216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200
78 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180
79 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160
80 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140
81 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120
82 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100
83 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70
84 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40
85 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
87 default-brightness-level = <200>;
88 enable-gpios = <&gpio0 GPIO_C4 GPIO_ACTIVE_HIGH>;
92 compatible = "rockchip_pwm_regulator";
93 pwms = <&pwm1 0 2000>;
95 rockchip,pwm_voltage_map= <925000 950000 975000 1000000 1025000 1050000 1075000 1100000 1125000 1150000 1175000 1200000 1225000 1250000 1275000 1300000 1325000 1350000 1375000 1400000>;
96 rockchip,pwm_voltage= <1000000>;
97 rockchip,pwm_min_voltage= <925000>;
98 rockchip,pwm_max_voltage= <1400000>;
99 rockchip,pwm_suspend_voltage= <950000>;
100 rockchip,pwm_coefficient= <475>;
102 #address-cells = <1>;
104 pwm_reg0: regulator@0 {
105 regulator-compatible = "pwm_dcdc1";
106 regulator-name= "vdd_logic";
107 regulator-min-microvolt = <925000>;
108 regulator-max-microvolt = <1400000>;
115 codec_hdmi_i2s: codec-hdmi-i2s {
116 compatible = "hdmi-i2s";
119 codec_hdmi_spdif: codec-hdmi-spdif {
120 compatible = "hdmi-spdif";
124 compatible = "rockchip-hdmi-i2s";
127 audio-codec = <&codec_hdmi_i2s>;
128 audio-controller = <&i2s0>;
131 //bitclock-inversion;
139 rockchip-hdmi-spdif {
140 compatible = "rockchip-hdmi-spdif";
143 audio-codec = <&codec_hdmi_spdif>;
144 audio-controller = <&spdif>;
150 compatible = "rockchip-rt5631";
153 audio-codec = <&rt5631>;
154 audio-controller = <&i2s0>;
157 //bitclock-inversion;
166 compatible = "rockchip-rt3261";
169 audio-codec = <&rt3261>;
170 audio-controller = <&i2s0>;
173 //bitclock-inversion;
179 audio-codec = <&rt3261>;
180 audio-controller = <&i2s0>;
192 compatible = "rockchip,rk3368-io-voltage-domain";
193 rockchip,grf = <&grf>;
194 rockchip,pmugrf = <&pmugrf>;
197 dvp-supply = <&ldo7_reg>; /*DVPIO_VDD*/
198 flash0-supply = <&dcdc2_reg>; /*FLASH0_VDD*/
199 wifi-supply = <&ldo7_reg>; /*APIO2_VDD*/
200 audio-supply = <&dcdc2_reg>; /*APIO3_VDD*/
201 sdcard-supply = <&ldo1_reg>; /*SDMMC0_VDD*/
202 gpio30-supply = <&dcdc2_reg>; /*APIO1_VDD*/
203 gpio1830-supply = <&dcdc2_reg>;/*ADIO4_VDD*/
206 pmu-supply = <&ldo5_reg>; /*PMUIO_VDD*/
207 vop-supply = <&ldo5_reg>; /*LCDC_VDD*/
216 clock-frequency = <125000000>;
220 // pmu_regulator = "act_ldo5";
221 // power-gpio = <&gpio0 GPIO_A6 GPIO_ACTIVE_HIGH>;
222 reset-gpio = <&gpio3 GPIO_B4 GPIO_ACTIVE_LOW>;
223 // phyirq-gpio = <&gpio0 GPIO_B1 GPIO_ACTIVE_LOW>;
225 pinctrl-names = "default";
226 pinctrl-0 = <&rgmii_pins>;
227 clock_in_out = "input";
230 status = "disabled"; //if want to use gmac, please set "okay"
234 //used for init some gpio
235 init-gpios = <&gpio0 GPIO_A6 GPIO_ACTIVE_HIGH>;
239 rockchip,pins = <0 GPIO_C7 RK_FUNC_GPIO &pcfg_pull_down>;
242 rockchip,pins = <0 GPIO_A3 RK_FUNC_3 &pcfg_pull_none>;
245 rockchip,pins = <0 GPIO_C2 RK_FUNC_GPIO &pcfg_pull_down>;
248 rockchip,pins = <0 GPIO_C1 RK_FUNC_GPIO &pcfg_pull_up>;
256 /*set "okay" both nand and emmc*/
257 /*if using nand,emmc need disabled*/
262 status = "disabled"; /* unused now,set "disabled"*/
266 clock-frequency = <100000000>;
267 clock-freq-min-max = <400000 100000000>;
274 //supports-DDR_MODE; //you should set the two value in your project. only close in RK3288-SDK board.
278 keep-power-in-suspend;
285 clock-frequency = <37500000>;
286 clock-freq-min-max = <400000 37500000>;
290 card-detect-delay = <200>;
293 keep-power-in-suspend;
295 vmmc-supply = <&ldo1_reg>;
300 clock-frequency = <50000000>;
301 clock-freq-min-max = <200000 50000000>;
305 keep-power-in-suspend;
312 max-freq = <48000000>;
315 compatible = "rockchip,spi_test_bus0_cs0";
317 spi-max-frequency = <24000000>;
327 compatible = "rockchip,spi_test_bus0_cs1";
329 spi-max-frequency = <24000000>;
341 max-freq = <48000000>;
344 compatible = "rockchip,spi_test_bus1_cs0";
346 spi-max-frequency = <24000000>;
354 compatible = "rockchip,spi_test_bus1_cs1";
356 spi-max-frequency = <24000000>;
368 max-freq = <48000000>;
371 compatible = "rockchip,spi_test_bus2_cs0";
373 spi-max-frequency = <24000000>;
389 dma-names = "!tx", "!rx";
390 pinctrl-0 = <&uart0_xfer &uart0_cts>;
394 tsadc-tshut-mode = <0>; /* tshut mode 0:CRU 1:GPIO */
395 //tsadc-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
402 compatible = "silergy,syr82x";
406 #address-cells = <1>;
408 syr827_dc1: regulator@0 {
410 regulator-compatible = "syr82x_dcdc1";
411 regulator-name = "vdd_arm";
412 regulator-min-microvolt = <712500>;
413 regulator-max-microvolt = <1500000>;
416 regulator-initial-mode = <0x2>;
417 regulator-initial-state = <3>;
418 regulator-state-mem {
419 regulator-state-mode = <0x2>;
420 regulator-state-disabled;
421 regulator-state-uv = <900000>;
427 compatible = "silergy,syr82x";
431 #address-cells = <1>;
433 syr828_dc1: regulator@0 {
435 regulator-compatible = "syr82x_dcdc1";
436 regulator-name = "vdd_gpu";
437 regulator-min-microvolt = <712500>;
438 regulator-max-microvolt = <1500000>;
441 regulator-initial-mode = <0x2>;
442 regulator-initial-state = <3>;
443 regulator-state-mem {
444 regulator-state-mode = <0x2>;
445 regulator-state-enabled;
446 regulator-state-uv = <900000>;
451 act8846: act8846@5a {
462 compatible = "cw201x";
464 dc_det_gpio = <&gpio0 GPIO_C1 GPIO_ACTIVE_LOW>;
465 bat_low_gpio = <&gpio0 GPIO_C2 GPIO_ACTIVE_LOW>;
466 chg_ok_gpio = <&gpio0 GPIO_D3 GPIO_ACTIVE_HIGH>;
467 bat_config_info = <0x15 0x42 0x60 0x59 0x52 0x58 0x4D 0x48 0x48 0x44 0x44 0x46 0x49 0x48 0x32
468 0x24 0x20 0x17 0x13 0x0F 0x19 0x3E 0x51 0x45 0x08 0x76 0x0B 0x85 0x0E 0x1C 0x2E 0x3E 0x4D 0x52 0x52
469 0x57 0x3D 0x1B 0x6A 0x2D 0x25 0x43 0x52 0x87 0x8F 0x91 0x94 0x52 0x82 0x8C 0x92 0x96 0xFF 0x7B 0xBB
470 0xCB 0x2F 0x7D 0x72 0xA5 0xB5 0xC1 0x46 0xAE>;
476 compatible = "rtc,hym8563";
478 irq_gpio = <&gpio0 GPIO_A1 IRQ_TYPE_EDGE_FALLING>;
487 compatible = "mpu6050";
489 mpu-int_config = <0x10>;
490 mpu-level_shifter = <0>;
491 mpu-orientation = <0 1 0 1 0 0 0 0 1>;
495 irq-gpio = <&gpio3 GPIO_B6 IRQ_TYPE_LEVEL_LOW>;
501 compatible = "mpu_ak8963";
504 compass-adapt_num = <0>;
505 compass-orientation = <1 0 0 0 1 0 0 0 1>;
514 compatible = "rt3261";
517 modem-input-mode = <1>;
518 lout-to-modem_mode = <1>;
527 compatible = "rt5631";
532 compatible = "goodix,gt9xx";
534 touch-gpio = <&gpio0 GPIO_B4 IRQ_TYPE_LEVEL_LOW>;
535 reset-gpio = <&gpio0 GPIO_B3 GPIO_ACTIVE_HIGH>;
557 rockchip,disp-mode = <NO_DUAL>;
558 rockchip,uboot-logo-on = <0>;
562 display-timings = <&disp_timings>;
567 pinctrl-names = "lcdc", "sleep";
568 pinctrl-0 = <&lcdc_lcdc>;
569 pinctrl-1 = <&lcdc_gpio>;
574 backlight = <&backlight>;
575 rockchip,mirror = <NO_MIRROR>;
576 rockchip,cabc_mode = <0>;
577 rockchip,fb-win-map = <FB_DEFAULT_ORDER>;
578 power_ctr: power_ctr {
579 rockchip,debug = <0>;
581 rockchip,power_type = <GPIO>;
582 gpios = <&gpio0 GPIO_C6 GPIO_ACTIVE_HIGH>;
583 rockchip,delay = <10>;
587 rockchip,power_type = <GPIO>;
588 gpios = <&gpio0 GPIO_C5 GPIO_ACTIVE_HIGH>;
589 rockchip,delay = <10>;
593 rockchip,power_type = <GPIO>;
594 gpios = <&gpio3 GPIO_D6 GPIO_ACTIVE_HIGH>;
595 rockchip,delay = <5>;
609 compatible = "rockchip_headset";
610 headset_gpio = <&gpio0 GPIO_C7 GPIO_ACTIVE_LOW>;
611 pinctrl-names = "default";
612 pinctrl-0 = <&gpio0_c7>;//gpio0_c7
613 rockchip,headset_wakeup = <0>;
616 hook_down_type = ; //interrupt hook key down status
621 compatible = "rockchip,key";
622 io-channels = <&adc 1>;
627 rockchip,adc_value = <1>;
632 label = "volume down";
633 rockchip,adc_value = <170>;
637 gpios = <&gpio0 GPIO_A2 GPIO_ACTIVE_LOW>;
646 rockchip,adc_value = <355>;
652 rockchip,adc_value = <746>;
658 rockchip,adc_value = <560>;
664 rockchip,adc_value = <450>;
673 &clk_core_b_dvfs_table {
689 pvtm-operating-points = <
690 /* KHz uV margin(uV)*/
697 1008000 1050000 25000
698 1200000 1150000 25000
699 1296000 1225000 25000
700 1416000 1300000 25000
701 1512000 1350000 25000
706 &clk_core_l_dvfs_table {
719 pvtm-operating-points = <
720 /* KHz uV margin(uV)*/
727 1008000 1125000 25000
728 1200000 1225000 25000
733 &clk_gpu_dvfs_table {
743 &clk_ddr_dvfs_table {
759 SYS_STATUS_NORMAL 600000
760 SYS_STATUS_SUSPEND 192000
761 SYS_STATUS_VIDEO_1080P 324000
762 SYS_STATUS_VIDEO_4K 600000
763 SYS_STATUS_PERFORMANCE 600000
764 SYS_STATUS_DUALVIEW 600000
765 SYS_STATUS_BOOST 396000
766 SYS_STATUS_ISP 528000
779 host_drv_gpio = <&gpio0 GPIO_A4 GPIO_ACTIVE_LOW>;
780 otg_drv_gpio = <&gpio0 GPIO_D1 GPIO_ACTIVE_LOW>;
782 rockchip,remote_wakeup;
783 rockchip,usb_irq_wakeup;
786 /include/ "../../../arm/boot/dts/act8846.dtsi"
788 gpios =<&gpio0 GPIO_B0 GPIO_ACTIVE_LOW>,<&gpio0 GPIO_A3 GPIO_ACTIVE_HIGH>;
789 act8846,system-power-controller;
793 dcdc1_reg: regulator@0{
794 regulator-name= "act_dcdc1";
795 regulator-min-microvolt = <1200000>;
796 regulator-max-microvolt = <1200000>;
801 dcdc2_reg: regulator@1 {
802 regulator-name= "vccio";
803 regulator-min-microvolt = <3300000>;
804 regulator-max-microvolt = <3300000>;
805 regulator-initial-state = <3>;
806 regulator-state-mem {
807 regulator-state-enabled;
808 regulator-state-uv = <3300000>;
812 dcdc3_reg: regulator@2 {
813 regulator-name= "vdd_logic";
814 regulator-min-microvolt = <700000>;
815 regulator-max-microvolt = <1500000>;
816 regulator-initial-state = <3>;
817 regulator-state-mem {
818 regulator-state-enabled;
819 regulator-state-uv = <1000000>;
824 dcdc4_reg: regulator@3 {
825 regulator-name= "act_dcdc4";
826 regulator-min-microvolt = <2000000>;
827 regulator-max-microvolt = <2000000>;
828 regulator-initial-state = <3>;
829 regulator-state-mem {
830 regulator-state-enabled;
831 regulator-state-uv = <2000000>;
835 ldo1_reg: regulator@4 {
836 regulator-name= "vccio_sd";
837 regulator-min-microvolt = <1800000>;
838 regulator-max-microvolt = <3300000>;
842 ldo2_reg: regulator@5 {
843 regulator-name= "act_ldo2";
844 regulator-min-microvolt = <1000000>;
845 regulator-max-microvolt = <1000000>;
849 ldo3_reg: regulator@6 {
850 regulator-name= "act_ldo3";
851 regulator-min-microvolt = <3300000>;
852 regulator-max-microvolt = <3300000>;
856 ldo4_reg:regulator@7 {
857 regulator-name= "act_ldo4";
858 regulator-min-microvolt = <3300000>;
859 regulator-max-microvolt = <3300000>;
863 ldo5_reg: regulator@8 {
864 regulator-name= "act_ldo5";
865 regulator-min-microvolt = <3300000>;
866 regulator-max-microvolt = <3300000>;
870 ldo6_reg: regulator@9 {
871 regulator-name= "act_ldo6";
872 regulator-min-microvolt = <1000000>;
873 regulator-max-microvolt = <1000000>;
874 regulator-initial-state = <3>;
875 regulator-state-mem {
876 regulator-state-enabled;
881 ldo7_reg: regulator@10 {
882 regulator-name= "vcc_18";
883 regulator-min-microvolt = <1800000>;
884 regulator-max-microvolt = <1800000>;
885 regulator-initial-state = <3>;
886 regulator-state-mem {
887 regulator-state-enabled;
892 ldo8_reg: regulator@11 {
893 regulator-name= "act_ldo8";
894 regulator-min-microvolt = <1800000>;
895 regulator-max-microvolt = <1800000>;
901 /include/ "../../../arm/boot/dts/rk818.dtsi"
903 gpios =<&gpio0 GPIO_A1 GPIO_ACTIVE_HIGH>,<&gpio0 GPIO_A0 GPIO_ACTIVE_LOW>;
904 rk818,system-power-controller;
905 pinctrl-names = "default";
906 pinctrl-0 = <&gpio0_c1>;
907 rk818,support_dc_chg = <1>;/*1:dc chg; 0:usb chg*/
910 rk818_dcdc1_reg: regulator@0{
911 regulator-name= "vdd_logic";/*vcc arm*/
912 regulator-min-microvolt = <700000>;/*<725000>;*/
913 regulator-max-microvolt = <1500000>;
914 regulator-initial-mode = <0x2>;
915 regulator-initial-state = <3>;
916 regulator-state-mem {
917 regulator-state-mode = <0x2>;
918 regulator-state-enabled;
919 regulator-state-uv =<1100000>;
923 rk818_dcdc2_reg: regulator@1 {
924 regulator-name= "rk818_dcdc2";/*vcc gpu*/
925 regulator-min-microvolt = <700000>;
926 regulator-max-microvolt = <1200000>;
927 regulator-initial-mode = <0x2>;
928 regulator-initial-state = <3>;
929 regulator-state-mem {
930 regulator-state-mode = <0x2>;
931 regulator-state-enabled;
932 regulator-state-uv = <1200000>;
936 rk818_dcdc3_reg: regulator@2 {
937 regulator-name= "rk818_dcdc3";
938 regulator-min-microvolt = <1200000>;
939 regulator-max-microvolt = <1200000>;
940 regulator-initial-mode = <0x2>;
941 regulator-initial-state = <3>;
942 regulator-state-mem {
943 regulator-state-mode = <0x2>;
944 regulator-state-enabled;
945 regulator-state-uv = <1200000>;
949 rk818_dcdc4_reg: regulator@3 {
950 regulator-name= "vccio";
951 regulator-min-microvolt = <3000000>;
952 regulator-max-microvolt = <3000000>;
953 regulator-initial-mode = <0x2>;
954 regulator-initial-state = <3>;
955 regulator-state-mem {
956 regulator-state-mode = <0x2>;
957 regulator-state-enabled;
958 regulator-state-uv = <3000000>;
962 rk818_ldo1_reg: regulator@4 {
963 regulator-name= "rk818_ldo1";
964 regulator-min-microvolt = <3300000>;
965 regulator-max-microvolt = <3300000>;
966 regulator-initial-state = <3>;
967 regulator-state-mem {
968 regulator-state-enabled;
969 regulator-state-uv = <3300000>;
973 rk818_ldo2_reg: regulator@5 {
974 regulator-name= "vcc_tp";
975 regulator-min-microvolt = <3000000>;
976 regulator-max-microvolt = <3000000>;
977 regulator-initial-state = <3>;
978 regulator-state-mem {
979 regulator-state-enabled;
980 regulator-state-uv = <3000000>;
984 rk818_ldo3_reg: regulator@6 {
985 regulator-name= "rk818_ldo3";
986 regulator-min-microvolt = <1000000>;
987 regulator-max-microvolt = <1000000>;
988 regulator-initial-state = <3>;
989 regulator-state-mem {
990 regulator-state-enabled;
991 regulator-state-uv = <1000000>;
995 rk818_ldo4_reg:regulator@7 {
996 regulator-name= "rk818_ldo4";
997 regulator-min-microvolt = <1800000>;
998 regulator-max-microvolt = <1800000>;
999 regulator-initial-state = <3>;
1000 regulator-state-mem {
1001 regulator-state-disabled;
1002 regulator-state-uv = <1800000>;
1006 rk818_ldo5_reg: regulator@8 {
1007 regulator-name= "rk818_ldo5";
1008 regulator-min-microvolt = <1800000>;
1009 regulator-max-microvolt = <1800000>;
1010 regulator-initial-state = <3>;
1011 regulator-state-mem {
1012 regulator-state-enabled;
1013 regulator-state-uv = <1800000>;
1017 rk818_ldo6_reg: regulator@9 {
1018 regulator-name= "rk818_ldo6";
1019 regulator-min-microvolt = <1000000>;
1020 regulator-max-microvolt = <1000000>;
1021 regulator-initial-state = <3>;
1022 regulator-state-mem {
1023 regulator-state-disabled;
1024 regulator-state-uv = <1000000>;
1028 rk818_ldo7_reg: regulator@10 {
1029 regulator-name= "rk818_ldo7";
1030 regulator-min-microvolt = <1800000>;
1031 regulator-max-microvolt = <1800000>;
1032 regulator-initial-state = <3>;
1033 regulator-state-mem {
1034 regulator-state-enabled;
1035 regulator-state-uv = <1800000>;
1039 rk818_ldo8_reg: regulator@11 {
1040 regulator-name= "rk818_ldo8";
1041 regulator-min-microvolt = <1800000>;
1042 regulator-max-microvolt = <1800000>;
1043 regulator-initial-state = <3>;
1044 regulator-state-mem {
1045 regulator-state-enabled;
1046 regulator-state-uv = <1800000>;
1050 rk818_ldo9_reg: regulator@12 {
1051 regulator-name= "vccio_sd";
1052 regulator-min-microvolt = <1800000>;
1053 regulator-max-microvolt = <3300000>;
1054 regulator-initial-state = <3>;
1055 regulator-state-mem {
1056 regulator-state-enabled;
1057 regulator-state-uv = <3300000>;
1061 rk818_ldo10_reg: regulator@13 {
1062 regulator-name= "rk818_ldo10";
1063 regulator-state-mem {
1064 regulator-state-disabled;
1070 ocv_table = <3350 3677 3693 3719 3752
1071 3770 3775 3778 3785 3796
1072 3812 3839 3881 3907 3933
1073 3958 3978 4033 4087 4123
1075 design_capacity = <8650>;
1076 design_qmax = <8800>;
1077 max_overcharge = <100>;
1078 max_input_currentmA = <3000>;
1079 max_chrg_currentmA = <1800>;
1080 max_charge_voltagemV = <4200>;
1081 sleep_enter_current = <600>;
1082 sleep_exit_current = <600>;
1083 power_off_thresd = <3400>;
1084 chrg_diff_voltagemV = <0>;
1085 virtual_power = <1>;
1086 support_usb_adp = <0>;
1087 support_dc_adp = <1>;
1088 dc_det_gpio = <&gpio0 GPIO_C1 GPIO_ACTIVE_LOW>;
1094 reg = <0x00000000 0x00000000>; /* 0MB */
1102 rockchip,ctrbits = <
1105 | RKPM_SLP_PMU_PLLS_PWRDN
1106 | RKPM_SLP_PMU_PMUALIVE_32K
1107 | RKPM_SLP_SFT_PLLS_DEEP
1108 | RKPM_SLP_PMU_DIS_OSC
1109 | RKPM_SLP_SFT_PD_NBSCUS
1120 status = "disabled";