3 #include <dt-bindings/interrupt-controller/arm-gic.h>
4 #include <dt-bindings/rkfb/rk_fb.h>
6 #include "../../../arm/boot/dts/vtl_ts_sdk8846.dtsi"
7 //#include "../../../arm/boot/dts/lcd-b101ew05.dtsi"
8 #include "../../../arm/boot/dts/lcd-tv080wum-mipi.dtsi"
9 #include "rk3368-cif-sensor.dtsi"
10 #include <dt-bindings/suspend/rockchip-rk3368.h>
14 bootargs = "earlyprintk=uart8250-32bit,0xff690000";
18 compatible = "wlan-platdata";
19 rockchip,grf = <&grf>;
21 /* wifi_chip_type - wifi chip define
22 * ap6210, ap6330, ap6335
23 * rtl8188eu, rtl8723bs, rtl8723bu
26 wifi_chip_type = "ap6335";
28 sdio_vref = <1800>; //1800mv or 3300mv
33 power_pmu_regulator = "act_ldo3";
34 power_pmu_enable_level = <1>; //1->HIGH, 0->LOW
37 //vref_ctrl_gpio = <&gpio0 GPIO_A2 GPIO_ACTIVE_HIGH>;
38 vref_pmu_regulator = "act_ldo3";
39 vref_pmu_enable_level = <1>; //1->HIGH, 0->LOW
41 WIFI,poweren_gpio = <&gpio3 GPIO_A4 GPIO_ACTIVE_HIGH>;
42 WIFI,host_wake_irq = <&gpio3 GPIO_A6 GPIO_ACTIVE_HIGH>;
43 //WIFI,reset_gpio = <&gpio0 GPIO_A2 GPIO_ACTIVE_LOW>;
49 compatible = "bluetooth-platdata";
51 //wifi-bt-power-toggle;
53 uart_rts_gpios = <&gpio2 GPIO_D3 GPIO_ACTIVE_LOW>;
54 pinctrl-names = "default","rts_gpio";
55 pinctrl-0 = <&uart0_rts>;
56 pinctrl-1 = <&uart0_rts_gpio>;
58 BT,power_gpio = <&gpio3 GPIO_A3 GPIO_ACTIVE_HIGH>;
59 BT,reset_gpio = <&gpio3 GPIO_A5 GPIO_ACTIVE_HIGH>;
60 BT,wake_gpio = <&gpio3 GPIO_A2 GPIO_ACTIVE_HIGH>;
61 BT,wake_host_irq = <&gpio3 GPIO_A7 GPIO_ACTIVE_HIGH>;
67 compatible = "hall_och165t";
68 type = <SENSOR_TYPE_HALL>;
69 irq-gpio = <&gpio0 GPIO_C0 IRQ_TYPE_EDGE_BOTH>;
72 backlight: backlight {
73 compatible = "pwm-backlight";
74 pwms = <&pwm0 0 25000>;
75 brightness-levels = <255 254 253 252 251 250 249 248 247 246 245 244 243 242 241 240
76 239 238 237 236 235 234 233 232 231 230 229 228 227 226 225 224 223 222 221 220
77 219 218 217 216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200
78 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180
79 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160
80 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140
81 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120
82 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100
83 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70
84 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40
85 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
87 default-brightness-level = <200>;
88 enable-gpios = <&gpio0 GPIO_C4 GPIO_ACTIVE_HIGH>;
92 compatible = "rockchip_pwm_regulator";
93 pwms = <&pwm1 0 2000>;
95 rockchip,pwm_voltage_map= <925000 950000 975000 1000000 1025000 1050000 1075000 1100000 1125000 1150000 1175000 1200000 1225000 1250000 1275000 1300000 1325000 1350000 1375000 1400000>;
96 rockchip,pwm_voltage= <1000000>;
97 rockchip,pwm_min_voltage= <925000>;
98 rockchip,pwm_max_voltage= <1400000>;
99 rockchip,pwm_suspend_voltage= <950000>;
100 rockchip,pwm_coefficient= <475>;
102 #address-cells = <1>;
104 pwm_reg0: regulator@0 {
105 regulator-compatible = "pwm_dcdc1";
106 regulator-name= "vdd_logic";
107 regulator-min-microvolt = <925000>;
108 regulator-max-microvolt = <1400000>;
115 codec_hdmi_i2s: codec-hdmi-i2s {
116 compatible = "hdmi-i2s";
119 codec_hdmi_spdif: codec-hdmi-spdif {
120 compatible = "hdmi-spdif";
124 compatible = "rockchip-hdmi-i2s";
127 audio-codec = <&codec_hdmi_i2s>;
128 audio-controller = <&i2s0>;
131 //bitclock-inversion;
139 rockchip-hdmi-spdif {
140 compatible = "rockchip-hdmi-spdif";
143 audio-codec = <&codec_hdmi_spdif>;
144 audio-controller = <&spdif>;
150 compatible = "rockchip-rt5631";
153 audio-codec = <&rt5631>;
154 audio-controller = <&i2s0>;
157 //bitclock-inversion;
166 compatible = "rockchip-rt3261";
169 audio-codec = <&rt3261>;
170 audio-controller = <&i2s0>;
173 //bitclock-inversion;
179 audio-codec = <&rt3261>;
180 audio-controller = <&i2s0>;
192 compatible = "rockchip,rk3368-io-voltage-domain";
193 rockchip,grf = <&grf>;
194 rockchip,pmugrf = <&pmugrf>;
197 dvp-supply = <&ldo7_reg>; /*DVPIO_VDD*/
198 flash0-supply = <&dcdc2_reg>; /*FLASH0_VDD*/
199 wifi-supply = <&ldo7_reg>; /*APIO2_VDD*/
200 audio-supply = <&dcdc2_reg>; /*APIO3_VDD*/
201 sdcard-supply = <&ldo1_reg>; /*SDMMC0_VDD*/
202 gpio30-supply = <&dcdc2_reg>; /*APIO1_VDD*/
203 gpio1830-supply = <&dcdc2_reg>;/*ADIO4_VDD*/
206 pmu-supply = <&ldo5_reg>; /*PMUIO_VDD*/
207 vop-supply = <&ldo5_reg>; /*LCDC_VDD*/
216 clock-frequency = <125000000>;
220 // pmu_regulator = "act_ldo5";
221 // power-gpio = <&gpio0 GPIO_A6 GPIO_ACTIVE_HIGH>;
222 reset-gpio = <&gpio3 GPIO_B4 GPIO_ACTIVE_LOW>;
223 // phyirq-gpio = <&gpio0 GPIO_B1 GPIO_ACTIVE_LOW>;
225 pinctrl-names = "default";
226 pinctrl-0 = <&rgmii_pins>;
227 clock_in_out = "input";
230 status = "disabled"; //if want to use gmac, please set "okay"
234 //used for init some gpio
235 init-gpios = <&gpio0 GPIO_A6 GPIO_ACTIVE_HIGH>;
239 rockchip,pins = <0 GPIO_C7 RK_FUNC_GPIO &pcfg_pull_down>;
242 rockchip,pins = <0 GPIO_A3 RK_FUNC_3 &pcfg_pull_none>;
245 rockchip,pins = <0 GPIO_C2 RK_FUNC_GPIO &pcfg_pull_down>;
248 rockchip,pins = <0 GPIO_C1 RK_FUNC_GPIO &pcfg_pull_up>;
256 /*set "okay" both nand and emmc*/
257 /*if using nand,emmc need disabled*/
262 status = "disabled"; /* unused now,set "disabled"*/
266 clock-frequency = <100000000>;
267 clock-freq-min-max = <400000 100000000>;
274 //supports-DDR_MODE; //you should set the two value in your project. only close in RK3288-SDK board.
278 keep-power-in-suspend;
285 clock-frequency = <50000000>;
286 clock-freq-min-max = <400000 50000000>;
290 card-detect-delay = <200>;
293 keep-power-in-suspend;
295 vmmc-supply = <&ldo1_reg>;
300 clock-frequency = <50000000>;
301 clock-freq-min-max = <200000 50000000>;
305 keep-power-in-suspend;
312 max-freq = <48000000>;
315 compatible = "rockchip,spi_test_bus0_cs0";
317 spi-max-frequency = <24000000>;
327 compatible = "rockchip,spi_test_bus0_cs1";
329 spi-max-frequency = <24000000>;
341 max-freq = <48000000>;
344 compatible = "rockchip,spi_test_bus1_cs0";
346 spi-max-frequency = <24000000>;
354 compatible = "rockchip,spi_test_bus1_cs1";
356 spi-max-frequency = <24000000>;
368 max-freq = <48000000>;
371 compatible = "rockchip,spi_test_bus2_cs0";
373 spi-max-frequency = <24000000>;
389 dma-names = "!tx", "!rx";
390 pinctrl-0 = <&uart0_xfer &uart0_cts>;
394 tsadc-tshut-mode = <0>; /* tshut mode 0:CRU 1:GPIO */
395 //tsadc-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
402 compatible = "silergy,syr82x";
406 #address-cells = <1>;
408 syr827_dc1: regulator@0 {
410 regulator-compatible = "syr82x_dcdc1";
411 regulator-name = "vdd_arm";
412 regulator-min-microvolt = <712500>;
413 regulator-max-microvolt = <1500000>;
416 regulator-initial-mode = <0x2>;
417 regulator-initial-state = <3>;
418 regulator-state-mem {
419 regulator-state-mode = <0x2>;
420 regulator-state-disabled;
421 regulator-state-uv = <900000>;
427 compatible = "silergy,syr82x";
431 #address-cells = <1>;
433 syr828_dc1: regulator@0 {
435 regulator-compatible = "syr82x_dcdc1";
436 regulator-name = "vdd_gpu";
437 regulator-min-microvolt = <712500>;
438 regulator-max-microvolt = <1500000>;
441 regulator-initial-mode = <0x2>;
442 regulator-initial-state = <3>;
443 regulator-state-mem {
444 regulator-state-mode = <0x2>;
445 regulator-state-enabled;
446 regulator-state-uv = <900000>;
451 act8846: act8846@5a {
462 compatible = "cw201x";
464 dc_det_gpio = <&gpio0 GPIO_C1 GPIO_ACTIVE_LOW>;
465 bat_low_gpio = <&gpio0 GPIO_C2 GPIO_ACTIVE_LOW>;
466 chg_ok_gpio = <&gpio0 GPIO_D3 GPIO_ACTIVE_HIGH>;
467 bat_config_info = <0x15 0x42 0x60 0x59 0x52 0x58 0x4D 0x48 0x48 0x44 0x44 0x46 0x49 0x48 0x32
468 0x24 0x20 0x17 0x13 0x0F 0x19 0x3E 0x51 0x45 0x08 0x76 0x0B 0x85 0x0E 0x1C 0x2E 0x3E 0x4D 0x52 0x52
469 0x57 0x3D 0x1B 0x6A 0x2D 0x25 0x43 0x52 0x87 0x8F 0x91 0x94 0x52 0x82 0x8C 0x92 0x96 0xFF 0x7B 0xBB
470 0xCB 0x2F 0x7D 0x72 0xA5 0xB5 0xC1 0x46 0xAE>;
476 compatible = "rtc,hym8563";
478 irq_gpio = <&gpio0 GPIO_A1 IRQ_TYPE_EDGE_FALLING>;
487 compatible = "mpu6050";
489 mpu-int_config = <0x10>;
490 mpu-level_shifter = <0>;
491 mpu-orientation = <0 1 0 1 0 0 0 0 1>;
495 irq-gpio = <&gpio3 GPIO_B6 IRQ_TYPE_LEVEL_LOW>;
501 compatible = "mpu_ak8963";
504 compass-adapt_num = <0>;
505 compass-orientation = <1 0 0 0 1 0 0 0 1>;
514 compatible = "rt3261";
517 modem-input-mode = <1>;
518 lout-to-modem_mode = <1>;
527 compatible = "rt5631";
532 compatible = "goodix,gt9xx";
534 touch-gpio = <&gpio0 GPIO_B4 IRQ_TYPE_LEVEL_LOW>;
535 reset-gpio = <&gpio0 GPIO_B3 GPIO_ACTIVE_HIGH>;
557 rockchip,disp-mode = <NO_DUAL>;
558 rockchip,uboot-logo-on = <0>;
562 display-timings = <&disp_timings>;
567 pinctrl-names = "lcdc", "sleep";
568 pinctrl-0 = <&lcdc_lcdc>;
569 pinctrl-1 = <&lcdc_gpio>;
574 backlight = <&backlight>;
575 rockchip,mirror = <NO_MIRROR>;
576 rockchip,cabc_mode = <0>;
577 rockchip,fb-win-map = <FB_DEFAULT_ORDER>;
578 power_ctr: power_ctr {
579 rockchip,debug = <0>;
581 rockchip,power_type = <GPIO>;
582 gpios = <&gpio0 GPIO_C6 GPIO_ACTIVE_HIGH>;
583 rockchip,delay = <10>;
587 rockchip,power_type = <GPIO>;
588 gpios = <&gpio0 GPIO_C5 GPIO_ACTIVE_HIGH>;
589 rockchip,delay = <10>;
593 rockchip,power_type = <GPIO>;
594 gpios = <&gpio3 GPIO_D6 GPIO_ACTIVE_HIGH>;
595 rockchip,delay = <5>;
609 compatible = "rockchip_headset";
610 headset_gpio = <&gpio0 GPIO_C7 GPIO_ACTIVE_LOW>;
611 pinctrl-names = "default";
612 pinctrl-0 = <&gpio0_c7>;//gpio0_c7
613 io-channels = <&adc 2>;
616 hook_down_type = ; //interrupt hook key down status
621 compatible = "rockchip,key";
622 io-channels = <&adc 1>;
627 rockchip,adc_value = <1>;
632 label = "volume down";
633 rockchip,adc_value = <170>;
637 gpios = <&gpio0 GPIO_A2 GPIO_ACTIVE_LOW>;
646 rockchip,adc_value = <355>;
652 rockchip,adc_value = <746>;
658 rockchip,adc_value = <560>;
664 rockchip,adc_value = <450>;
673 &clk_core_b_dvfs_table {
691 &clk_core_l_dvfs_table {
706 &clk_gpu_dvfs_table {
716 &clk_ddr_dvfs_table {
732 SYS_STATUS_NORMAL 600000
733 SYS_STATUS_SUSPEND 192000
734 SYS_STATUS_VIDEO_1080P 324000
735 SYS_STATUS_VIDEO_4K 600000
736 SYS_STATUS_PERFORMANCE 600000
737 SYS_STATUS_DUALVIEW 600000
738 SYS_STATUS_BOOST 396000
739 SYS_STATUS_ISP 528000
752 host_drv_gpio = <&gpio0 GPIO_A4 GPIO_ACTIVE_LOW>;
753 otg_drv_gpio = <&gpio0 GPIO_D1 GPIO_ACTIVE_LOW>;
755 rockchip,remote_wakeup;
756 rockchip,usb_irq_wakeup;
759 /include/ "../../../arm/boot/dts/act8846.dtsi"
761 gpios =<&gpio0 GPIO_B0 GPIO_ACTIVE_LOW>,<&gpio0 GPIO_A3 GPIO_ACTIVE_HIGH>;
762 act8846,system-power-controller;
766 dcdc1_reg: regulator@0{
767 regulator-name= "act_dcdc1";
768 regulator-min-microvolt = <1200000>;
769 regulator-max-microvolt = <1200000>;
774 dcdc2_reg: regulator@1 {
775 regulator-name= "vccio";
776 regulator-min-microvolt = <3300000>;
777 regulator-max-microvolt = <3300000>;
778 regulator-initial-state = <3>;
779 regulator-state-mem {
780 regulator-state-enabled;
781 regulator-state-uv = <3300000>;
785 dcdc3_reg: regulator@2 {
786 regulator-name= "vdd_logic";
787 regulator-min-microvolt = <700000>;
788 regulator-max-microvolt = <1500000>;
789 regulator-initial-state = <3>;
790 regulator-state-mem {
791 regulator-state-enabled;
792 regulator-state-uv = <1000000>;
797 dcdc4_reg: regulator@3 {
798 regulator-name= "act_dcdc4";
799 regulator-min-microvolt = <2000000>;
800 regulator-max-microvolt = <2000000>;
801 regulator-initial-state = <3>;
802 regulator-state-mem {
803 regulator-state-enabled;
804 regulator-state-uv = <2000000>;
808 ldo1_reg: regulator@4 {
809 regulator-name= "vccio_sd";
810 regulator-min-microvolt = <1800000>;
811 regulator-max-microvolt = <3300000>;
815 ldo2_reg: regulator@5 {
816 regulator-name= "act_ldo2";
817 regulator-min-microvolt = <1000000>;
818 regulator-max-microvolt = <1000000>;
822 ldo3_reg: regulator@6 {
823 regulator-name= "act_ldo3";
824 regulator-min-microvolt = <3300000>;
825 regulator-max-microvolt = <3300000>;
829 ldo4_reg:regulator@7 {
830 regulator-name= "act_ldo4";
831 regulator-min-microvolt = <3300000>;
832 regulator-max-microvolt = <3300000>;
836 ldo5_reg: regulator@8 {
837 regulator-name= "act_ldo5";
838 regulator-min-microvolt = <3300000>;
839 regulator-max-microvolt = <3300000>;
843 ldo6_reg: regulator@9 {
844 regulator-name= "act_ldo6";
845 regulator-min-microvolt = <1000000>;
846 regulator-max-microvolt = <1000000>;
847 regulator-initial-state = <3>;
848 regulator-state-mem {
849 regulator-state-enabled;
854 ldo7_reg: regulator@10 {
855 regulator-name= "vcc_18";
856 regulator-min-microvolt = <1800000>;
857 regulator-max-microvolt = <1800000>;
858 regulator-initial-state = <3>;
859 regulator-state-mem {
860 regulator-state-enabled;
865 ldo8_reg: regulator@11 {
866 regulator-name= "act_ldo8";
867 regulator-min-microvolt = <1800000>;
868 regulator-max-microvolt = <1800000>;
874 /include/ "../../../arm/boot/dts/rk818.dtsi"
876 gpios =<&gpio0 GPIO_A1 GPIO_ACTIVE_HIGH>,<&gpio0 GPIO_A0 GPIO_ACTIVE_LOW>;
877 rk818,system-power-controller;
878 pinctrl-names = "default";
879 pinctrl-0 = <&gpio0_c1>;
880 rk818,support_dc_chg = <1>;/*1:dc chg; 0:usb chg*/
883 rk818_dcdc1_reg: regulator@0{
884 regulator-name= "vdd_logic";/*vcc arm*/
885 regulator-min-microvolt = <700000>;/*<725000>;*/
886 regulator-max-microvolt = <1500000>;
887 regulator-initial-mode = <0x2>;
888 regulator-initial-state = <3>;
889 regulator-state-mem {
890 regulator-state-mode = <0x2>;
891 regulator-state-enabled;
892 regulator-state-uv =<1100000>;
896 rk818_dcdc2_reg: regulator@1 {
897 regulator-name= "rk818_dcdc2";/*vcc gpu*/
898 regulator-min-microvolt = <700000>;
899 regulator-max-microvolt = <1200000>;
900 regulator-initial-mode = <0x2>;
901 regulator-initial-state = <3>;
902 regulator-state-mem {
903 regulator-state-mode = <0x2>;
904 regulator-state-enabled;
905 regulator-state-uv = <1200000>;
909 rk818_dcdc3_reg: regulator@2 {
910 regulator-name= "rk818_dcdc3";
911 regulator-min-microvolt = <1200000>;
912 regulator-max-microvolt = <1200000>;
913 regulator-initial-mode = <0x2>;
914 regulator-initial-state = <3>;
915 regulator-state-mem {
916 regulator-state-mode = <0x2>;
917 regulator-state-enabled;
918 regulator-state-uv = <1200000>;
922 rk818_dcdc4_reg: regulator@3 {
923 regulator-name= "vccio";
924 regulator-min-microvolt = <3000000>;
925 regulator-max-microvolt = <3000000>;
926 regulator-initial-mode = <0x2>;
927 regulator-initial-state = <3>;
928 regulator-state-mem {
929 regulator-state-mode = <0x2>;
930 regulator-state-enabled;
931 regulator-state-uv = <3000000>;
935 rk818_ldo1_reg: regulator@4 {
936 regulator-name= "rk818_ldo1";
937 regulator-min-microvolt = <3300000>;
938 regulator-max-microvolt = <3300000>;
939 regulator-initial-state = <3>;
940 regulator-state-mem {
941 regulator-state-enabled;
942 regulator-state-uv = <3300000>;
946 rk818_ldo2_reg: regulator@5 {
947 regulator-name= "rk818_ldo2";
948 regulator-min-microvolt = <3000000>;
949 regulator-max-microvolt = <3000000>;
950 regulator-initial-state = <3>;
951 regulator-state-mem {
952 regulator-state-enabled;
953 regulator-state-uv = <3000000>;
957 rk818_ldo3_reg: regulator@6 {
958 regulator-name= "rk818_ldo3";
959 regulator-min-microvolt = <1000000>;
960 regulator-max-microvolt = <1000000>;
961 regulator-initial-state = <3>;
962 regulator-state-mem {
963 regulator-state-enabled;
964 regulator-state-uv = <1000000>;
968 rk818_ldo4_reg:regulator@7 {
969 regulator-name= "rk818_ldo4";
970 regulator-min-microvolt = <1800000>;
971 regulator-max-microvolt = <1800000>;
972 regulator-initial-state = <3>;
973 regulator-state-mem {
974 regulator-state-disabled;
975 regulator-state-uv = <1800000>;
979 rk818_ldo5_reg: regulator@8 {
980 regulator-name= "rk818_ldo5";
981 regulator-min-microvolt = <1800000>;
982 regulator-max-microvolt = <1800000>;
983 regulator-initial-state = <3>;
984 regulator-state-mem {
985 regulator-state-enabled;
986 regulator-state-uv = <1800000>;
990 rk818_ldo6_reg: regulator@9 {
991 regulator-name= "rk818_ldo6";
992 regulator-min-microvolt = <1000000>;
993 regulator-max-microvolt = <1000000>;
994 regulator-initial-state = <3>;
995 regulator-state-mem {
996 regulator-state-disabled;
997 regulator-state-uv = <1000000>;
1001 rk818_ldo7_reg: regulator@10 {
1002 regulator-name= "rk818_ldo7";
1003 regulator-min-microvolt = <1800000>;
1004 regulator-max-microvolt = <1800000>;
1005 regulator-initial-state = <3>;
1006 regulator-state-mem {
1007 regulator-state-enabled;
1008 regulator-state-uv = <1800000>;
1012 rk818_ldo8_reg: regulator@11 {
1013 regulator-name= "rk818_ldo8";
1014 regulator-min-microvolt = <1800000>;
1015 regulator-max-microvolt = <1800000>;
1016 regulator-initial-state = <3>;
1017 regulator-state-mem {
1018 regulator-state-enabled;
1019 regulator-state-uv = <1800000>;
1023 rk818_ldo9_reg: regulator@12 {
1024 regulator-name= "vccio_sd";
1025 regulator-min-microvolt = <1800000>;
1026 regulator-max-microvolt = <3300000>;
1027 regulator-initial-state = <3>;
1028 regulator-state-mem {
1029 regulator-state-enabled;
1030 regulator-state-uv = <3300000>;
1034 rk818_ldo10_reg: regulator@13 {
1035 regulator-name= "rk818_ldo10";
1036 regulator-state-mem {
1037 regulator-state-disabled;
1043 ocv_table = <3350 3677 3693 3719 3752
1044 3770 3775 3778 3785 3796
1045 3812 3839 3881 3907 3933
1046 3958 3978 4033 4087 4123
1048 design_capacity = <8650>;
1049 design_qmax = <8800>;
1050 max_overcharge = <100>;
1051 max_input_currentmA = <3000>;
1052 max_chrg_currentmA = <1800>;
1053 max_charge_voltagemV = <4200>;
1054 sleep_enter_current = <600>;
1055 sleep_exit_current = <600>;
1056 power_off_thresd = <3400>;
1057 chrg_diff_voltagemV = <0>;
1058 virtual_power = <1>;
1059 support_usb_adp = <0>;
1060 support_dc_adp = <1>;
1061 dc_det_gpio = <&gpio0 GPIO_C1 GPIO_ACTIVE_LOW>;
1067 reg = <0x00000000 0x00000000>; /* 0MB */
1075 rockchip,ctrbits = <
1078 | RKPM_SLP_PMU_PLLS_PWRDN
1079 | RKPM_SLP_PMU_PMUALIVE_32K
1080 | RKPM_SLP_SFT_PLLS_DEEP
1081 | RKPM_SLP_PMU_DIS_OSC
1082 | RKPM_SLP_SFT_PD_NBSCUS
1093 status = "disabled";