2 # Touchscreen driver configuration
4 menuconfig INPUT_TOUCHSCREEN
7 Say Y here, and a list of supported touchscreens will be displayed.
8 This option doesn't affect the kernel.
14 config TOUCHSCREEN_88PM860X
15 tristate "Marvell 88PM860x touchscreen"
16 depends on MFD_88PM860X
18 Say Y here if you have a 88PM860x PMIC and want to enable
19 support for the built-in touchscreen.
23 To compile this driver as a module, choose M here: the
24 module will be called 88pm860x-ts.
26 config TOUCHSCREEN_ADS7846
27 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
29 depends on HWMON = n || HWMON
31 Say Y here if you have a touchscreen interface using the
32 ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
33 and your board-specific setup code includes that in its
36 If HWMON is selected, and the driver is told the reference voltage
37 on your board, you will also get hwmon interfaces for the voltage
38 (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
40 If unsure, say N (but it's safe to say "Y").
42 To compile this driver as a module, choose M here: the
43 module will be called ads7846.
45 config TOUCHSCREEN_AD7877
46 tristate "AD7877 based touchscreens"
49 Say Y here if you have a touchscreen interface using the
50 AD7877 controller, and your board-specific initialization
51 code includes that in its table of SPI devices.
53 If unsure, say N (but it's safe to say "Y").
55 To compile this driver as a module, choose M here: the
56 module will be called ad7877.
58 config TOUCHSCREEN_AD7879
59 tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
61 Say Y here if you want to support a touchscreen interface using
62 the AD7879-1/AD7889-1 controller.
64 You should select a bus connection too.
66 To compile this driver as a module, choose M here: the
67 module will be called ad7879.
69 config TOUCHSCREEN_AD7879_I2C
70 tristate "support I2C bus connection"
71 depends on TOUCHSCREEN_AD7879 && I2C
73 Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
75 To compile this driver as a module, choose M here: the
76 module will be called ad7879-i2c.
78 config TOUCHSCREEN_AD7879_SPI
79 tristate "support SPI bus connection"
80 depends on TOUCHSCREEN_AD7879 && SPI_MASTER
82 Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
84 If unsure, say N (but it's safe to say "Y").
86 To compile this driver as a module, choose M here: the
87 module will be called ad7879-spi.
89 config TOUCHSCREEN_ATMEL_MXT
90 tristate "Atmel mXT I2C Touchscreen"
93 Say Y here if you have Atmel mXT series I2C touchscreen,
94 such as AT42QT602240/ATMXT224, connected to your system.
98 To compile this driver as a module, choose M here: the
99 module will be called atmel_mxt_ts.
101 config TOUCHSCREEN_AUO_PIXCIR
102 tristate "AUO in-cell touchscreen using Pixcir ICs"
106 Say Y here if you have a AUO display with in-cell touchscreen
111 To compile this driver as a module, choose M here: the
112 module will be called auo-pixcir-ts.
114 config TOUCHSCREEN_BITSY
115 tristate "Compaq iPAQ H3600 (Bitsy) touchscreen"
116 depends on SA1100_BITSY
119 Say Y here if you have the h3600 (Bitsy) touchscreen.
123 To compile this driver as a module, choose M here: the
124 module will be called h3600_ts_input.
126 config TOUCHSCREEN_BU21013
127 tristate "BU21013 based touch panel controllers"
130 Say Y here if you have a bu21013 touchscreen connected to
135 To compile this driver as a module, choose M here: the
136 module will be called bu21013_ts.
138 config TOUCHSCREEN_CY8CTMG110
139 tristate "cy8ctmg110 touchscreen"
143 Say Y here if you have a cy8ctmg110 capacitive touchscreen on
148 To compile this driver as a module, choose M here: the
149 module will be called cy8ctmg110_ts.
151 config TOUCHSCREEN_CYTTSP_CORE
152 tristate "Cypress TTSP touchscreen"
154 Say Y here if you have a touchscreen using controller from
155 the Cypress TrueTouch(tm) Standard Product family connected
156 to your system. You will also need to select appropriate
157 bus connection below.
161 To compile this driver as a module, choose M here: the
162 module will be called cyttsp_core.
164 config TOUCHSCREEN_CYTTSP_I2C
165 tristate "support I2C bus connection"
166 depends on TOUCHSCREEN_CYTTSP_CORE && I2C
168 Say Y here if the touchscreen is connected via I2C bus.
170 To compile this driver as a module, choose M here: the
171 module will be called cyttsp_i2c.
173 config TOUCHSCREEN_CYTTSP_SPI
174 tristate "support SPI bus connection"
175 depends on TOUCHSCREEN_CYTTSP_CORE && SPI_MASTER
177 Say Y here if the touchscreen is connected via SPI bus.
179 To compile this driver as a module, choose M here: the
180 module will be called cyttsp_spi.
182 config TOUCHSCREEN_DA9034
183 tristate "Touchscreen support for Dialog Semiconductor DA9034"
184 depends on PMIC_DA903X
187 Say Y here to enable the support for the touchscreen found
188 on Dialog Semiconductor DA9034 PMIC.
190 config TOUCHSCREEN_DYNAPRO
191 tristate "Dynapro serial touchscreen"
194 Say Y here if you have a Dynapro serial touchscreen connected to
199 To compile this driver as a module, choose M here: the
200 module will be called dynapro.
202 config TOUCHSCREEN_HAMPSHIRE
203 tristate "Hampshire serial touchscreen"
206 Say Y here if you have a Hampshire serial touchscreen connected to
211 To compile this driver as a module, choose M here: the
212 module will be called hampshire.
214 config TOUCHSCREEN_EETI
215 tristate "EETI touchscreen panel support"
218 Say Y here to enable support for I2C connected EETI touch panels.
220 To compile this driver as a module, choose M here: the
221 module will be called eeti_ts.
223 config TOUCHSCREEN_EGALAX
224 tristate "EETI eGalax multi-touch panel support"
227 Say Y here to enable support for I2C connected EETI
228 eGalax multi-touch panels.
230 To compile this driver as a module, choose M here: the
231 module will be called egalax_ts.
233 config TOUCHSCREEN_FUJITSU
234 tristate "Fujitsu serial touchscreen"
237 Say Y here if you have the Fujitsu touchscreen (such as one
238 installed in Lifebook P series laptop) connected to your
243 To compile this driver as a module, choose M here: the
244 module will be called fujitsu-ts.
246 config TOUCHSCREEN_ILI210X
247 tristate "Ilitek ILI210X based touchscreen"
250 Say Y here if you have a ILI210X based touchscreen
251 controller. This driver supports models ILI2102,
252 ILI2102s, ILI2103, ILI2103s and ILI2105.
253 Such kind of chipsets can be found in Amazon Kindle Fire
258 To compile this driver as a module, choose M here: the
259 module will be called ili210x.
261 config TOUCHSCREEN_S3C2410
262 tristate "Samsung S3C2410/generic touchscreen input driver"
263 depends on ARCH_S3C24XX || SAMSUNG_DEV_TS
266 Say Y here if you have the s3c2410 touchscreen.
270 To compile this driver as a module, choose M here: the
271 module will be called s3c2410_ts.
273 config TOUCHSCREEN_GUNZE
274 tristate "Gunze AHL-51S touchscreen"
277 Say Y here if you have the Gunze AHL-51 touchscreen connected to
282 To compile this driver as a module, choose M here: the
283 module will be called gunze.
285 config TOUCHSCREEN_ELO
286 tristate "Elo serial touchscreens"
289 Say Y here if you have an Elo serial touchscreen connected to
294 To compile this driver as a module, choose M here: the
295 module will be called elo.
297 config TOUCHSCREEN_WACOM_W8001
298 tristate "Wacom W8001 penabled serial touchscreen"
301 Say Y here if you have an Wacom W8001 penabled serial touchscreen
302 connected to your system.
306 To compile this driver as a module, choose M here: the
307 module will be called wacom_w8001.
309 config TOUCHSCREEN_WACOM_I2C
310 tristate "Wacom Tablet support (I2C)"
313 Say Y here if you want to use the I2C version of the Wacom
318 To compile this driver as a module, choose M here: the module
319 will be called wacom_i2c.
321 config TOUCHSCREEN_LPC32XX
322 tristate "LPC32XX touchscreen controller"
323 depends on ARCH_LPC32XX
325 Say Y here if you have a LPC32XX device and want
326 to support the built-in touchscreen.
328 To compile this driver as a module, choose M here: the
329 module will be called lpc32xx_ts.
331 config TOUCHSCREEN_MAX11801
332 tristate "MAX11801 based touchscreens"
335 Say Y here if you have a MAX11801 based touchscreen
340 To compile this driver as a module, choose M here: the
341 module will be called max11801_ts.
343 config TOUCHSCREEN_MCS5000
344 tristate "MELFAS MCS-5000 touchscreen"
347 Say Y here if you have the MELFAS MCS-5000 touchscreen controller
352 To compile this driver as a module, choose M here: the
353 module will be called mcs5000_ts.
355 config TOUCHSCREEN_MTOUCH
356 tristate "MicroTouch serial touchscreens"
359 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
364 To compile this driver as a module, choose M here: the
365 module will be called mtouch.
367 config TOUCHSCREEN_INEXIO
368 tristate "iNexio serial touchscreens"
371 Say Y here if you have an iNexio serial touchscreen connected to
376 To compile this driver as a module, choose M here: the
377 module will be called inexio.
379 config TOUCHSCREEN_INTEL_MID
380 tristate "Intel MID platform resistive touchscreen"
381 depends on INTEL_SCU_IPC
383 Say Y here if you have a Intel MID based touchscreen in
388 To compile this driver as a module, choose M here: the
389 module will be called intel_mid_touch.
391 config TOUCHSCREEN_MK712
392 tristate "ICS MicroClock MK712 touchscreen"
394 Say Y here if you have the ICS MicroClock MK712 touchscreen
395 controller chip in your system.
399 To compile this driver as a module, choose M here: the
400 module will be called mk712.
402 config TOUCHSCREEN_HP600
403 tristate "HP Jornada 6xx touchscreen"
404 depends on SH_HP6XX && SH_ADC
406 Say Y here if you have a HP Jornada 620/660/680/690 and want to
407 support the built-in touchscreen.
409 To compile this driver as a module, choose M here: the
410 module will be called hp680_ts_input.
412 config TOUCHSCREEN_HP7XX
413 tristate "HP Jornada 7xx touchscreen"
414 depends on SA1100_JORNADA720_SSP
416 Say Y here if you have a HP Jornada 710/720/728 and want
417 to support the built-in touchscreen.
419 To compile this driver as a module, choose M here: the
420 module will be called jornada720_ts.
422 config TOUCHSCREEN_HTCPEN
423 tristate "HTC Shift X9500 touchscreen"
426 Say Y here if you have an HTC Shift UMPC also known as HTC X9500
427 Clio / Shangrila and want to support the built-in touchscreen.
431 To compile this driver as a module, choose M here: the
432 module will be called htcpen.
434 config TOUCHSCREEN_PENMOUNT
435 tristate "Penmount serial touchscreen"
438 Say Y here if you have a Penmount serial touchscreen connected to
443 To compile this driver as a module, choose M here: the
444 module will be called penmount.
446 config TOUCHSCREEN_MIGOR
447 tristate "Renesas MIGO-R touchscreen"
448 depends on SH_MIGOR && I2C
450 Say Y here to enable MIGO-R touchscreen support.
454 To compile this driver as a module, choose M here: the
455 module will be called migor_ts.
457 config TOUCHSCREEN_TNETV107X
458 tristate "TI TNETV107X touchscreen support"
459 depends on ARCH_DAVINCI_TNETV107X
461 Say Y here if you want to use the TNETV107X touchscreen.
463 To compile this driver as a module, choose M here: the
464 module will be called tnetv107x-ts.
466 config TOUCHSCREEN_TOUCHRIGHT
467 tristate "Touchright serial touchscreen"
470 Say Y here if you have a Touchright serial touchscreen connected to
475 To compile this driver as a module, choose M here: the
476 module will be called touchright.
478 config TOUCHSCREEN_TOUCHWIN
479 tristate "Touchwin serial touchscreen"
482 Say Y here if you have a Touchwin serial touchscreen connected to
487 To compile this driver as a module, choose M here: the
488 module will be called touchwin.
490 config TOUCHSCREEN_TI_TSCADC
491 tristate "TI Touchscreen Interface"
492 depends on ARCH_OMAP2PLUS
494 Say Y here if you have 4/5/8 wire touchscreen controller
495 to be connected to the ADC controller on your TI AM335x SoC.
499 To compile this driver as a module, choose M here: the
500 module will be called ti_tscadc.
502 config TOUCHSCREEN_ATMEL_TSADCC
503 tristate "Atmel Touchscreen Interface"
504 depends on ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
506 Say Y here if you have a 4-wire touchscreen connected to the
507 ADC Controller on your Atmel SoC (such as the AT91SAM9RL).
511 To compile this driver as a module, choose M here: the
512 module will be called atmel_tsadcc.
514 config TOUCHSCREEN_UCB1400
515 tristate "Philips UCB1400 touchscreen"
517 depends on UCB1400_CORE
519 This enables support for the Philips UCB1400 touchscreen interface.
520 The UCB1400 is an AC97 audio codec. The touchscreen interface
521 will be initialized only after the ALSA subsystem has been
522 brought up and the UCB1400 detected. You therefore have to
523 configure ALSA support as well (either built-in or modular,
524 independently of whether this driver is itself built-in or
525 modular) for this driver to work.
527 To compile this driver as a module, choose M here: the
528 module will be called ucb1400_ts.
530 config TOUCHSCREEN_PIXCIR
531 tristate "PIXCIR I2C touchscreens"
534 Say Y here if you have a pixcir i2c touchscreen
539 To compile this driver as a module, choose M here: the
540 module will be called pixcir_i2c_ts.
542 config TOUCHSCREEN_WM831X
543 tristate "Support for WM831x touchscreen controllers"
544 depends on MFD_WM831X
546 This enables support for the touchscreen controller on the WM831x
549 To compile this driver as a module, choose M here: the
550 module will be called wm831x-ts.
552 config TOUCHSCREEN_WM97XX
553 tristate "Support for WM97xx AC97 touchscreen controllers"
556 Say Y here if you have a Wolfson Microelectronics WM97xx
557 touchscreen connected to your system. Note that this option
558 only enables core driver, you will also need to select
559 support for appropriate chip below.
563 To compile this driver as a module, choose M here: the
564 module will be called wm97xx-ts.
566 config TOUCHSCREEN_WM9705
567 bool "WM9705 Touchscreen interface support"
568 depends on TOUCHSCREEN_WM97XX
571 Say Y here to enable support for the Wolfson Microelectronics
572 WM9705 touchscreen controller.
574 config TOUCHSCREEN_WM9712
575 bool "WM9712 Touchscreen interface support"
576 depends on TOUCHSCREEN_WM97XX
579 Say Y here to enable support for the Wolfson Microelectronics
580 WM9712 touchscreen controller.
582 config TOUCHSCREEN_WM9713
583 bool "WM9713 Touchscreen interface support"
584 depends on TOUCHSCREEN_WM97XX
587 Say Y here to enable support for the Wolfson Microelectronics
588 WM9713 touchscreen controller.
590 config TOUCHSCREEN_WM97XX_ATMEL
591 tristate "WM97xx Atmel accelerated touch"
592 depends on TOUCHSCREEN_WM97XX && (AVR32 || ARCH_AT91)
594 Say Y here for support for streaming mode with WM97xx touchscreens
595 on Atmel AT91 or AVR32 systems with an AC97C module.
597 Be aware that this will use channel B in the controller for
598 streaming data, this must not conflict with other AC97C drivers.
602 To compile this driver as a module, choose M here: the module will
603 be called atmel-wm97xx.
605 config TOUCHSCREEN_WM97XX_MAINSTONE
606 tristate "WM97xx Mainstone/Palm accelerated touch"
607 depends on TOUCHSCREEN_WM97XX && ARCH_PXA
609 Say Y here for support for streaming mode with WM97xx touchscreens
610 on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.
614 To compile this driver as a module, choose M here: the
615 module will be called mainstone-wm97xx.
617 config TOUCHSCREEN_WM97XX_ZYLONITE
618 tristate "Zylonite accelerated touch"
619 depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE
620 select TOUCHSCREEN_WM9713
622 Say Y here for support for streaming mode with the touchscreen
627 To compile this driver as a module, choose M here: the
628 module will be called zylonite-wm97xx.
630 config TOUCHSCREEN_USB_COMPOSITE
631 tristate "USB Touchscreen Driver"
632 depends on USB_ARCH_HAS_HCD
635 USB Touchscreen driver for:
636 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
637 - PanJit TouchSet USB
638 - 3M MicroTouch USB (EX II series)
640 - some other eTurboTouch
643 - IRTOUCHSYSTEMS/UNITOP
645 - GoTop Super_Q2/GogoPen/PenPower tablets
646 - JASTEC USB Touch Controller/DigiTech DTR-02U
647 - Zytronic controllers
648 - Elo TouchSystems 2700 IntelliTouch
649 - EasyTouch USB Touch Controller from Data Modul
651 Have a look at <http://linux.chapter7.ch/touchkit/> for
652 a usage description and the required user-space stuff.
654 To compile this driver as a module, choose M here: the
655 module will be called usbtouchscreen.
657 config TOUCHSCREEN_MC13783
658 tristate "Freescale MC13783 touchscreen input driver"
659 depends on MFD_MC13783
661 Say Y here if you have an Freescale MC13783 PMIC on your
662 board and want to use its touchscreen
666 To compile this driver as a module, choose M here: the
667 module will be called mc13783_ts.
669 config TOUCHSCREEN_USB_EGALAX
671 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EXPERT
672 depends on TOUCHSCREEN_USB_COMPOSITE
674 config TOUCHSCREEN_USB_PANJIT
676 bool "PanJit device support" if EXPERT
677 depends on TOUCHSCREEN_USB_COMPOSITE
679 config TOUCHSCREEN_USB_3M
681 bool "3M/Microtouch EX II series device support" if EXPERT
682 depends on TOUCHSCREEN_USB_COMPOSITE
684 config TOUCHSCREEN_USB_ITM
686 bool "ITM device support" if EXPERT
687 depends on TOUCHSCREEN_USB_COMPOSITE
689 config TOUCHSCREEN_USB_ETURBO
691 bool "eTurboTouch (non-eGalax compatible) device support" if EXPERT
692 depends on TOUCHSCREEN_USB_COMPOSITE
694 config TOUCHSCREEN_USB_GUNZE
696 bool "Gunze AHL61 device support" if EXPERT
697 depends on TOUCHSCREEN_USB_COMPOSITE
699 config TOUCHSCREEN_USB_DMC_TSC10
701 bool "DMC TSC-10/25 device support" if EXPERT
702 depends on TOUCHSCREEN_USB_COMPOSITE
704 config TOUCHSCREEN_USB_IRTOUCH
706 bool "IRTOUCHSYSTEMS/UNITOP device support" if EXPERT
707 depends on TOUCHSCREEN_USB_COMPOSITE
709 config TOUCHSCREEN_USB_IDEALTEK
711 bool "IdealTEK URTC1000 device support" if EXPERT
712 depends on TOUCHSCREEN_USB_COMPOSITE
714 config TOUCHSCREEN_USB_GENERAL_TOUCH
716 bool "GeneralTouch Touchscreen device support" if EXPERT
717 depends on TOUCHSCREEN_USB_COMPOSITE
719 config TOUCHSCREEN_USB_GOTOP
721 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EXPERT
722 depends on TOUCHSCREEN_USB_COMPOSITE
724 config TOUCHSCREEN_USB_JASTEC
726 bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EXPERT
727 depends on TOUCHSCREEN_USB_COMPOSITE
729 config TOUCHSCREEN_USB_ELO
731 bool "Elo TouchSystems 2700 IntelliTouch controller device support" if EXPERT
732 depends on TOUCHSCREEN_USB_COMPOSITE
734 config TOUCHSCREEN_USB_E2I
736 bool "e2i Touchscreen controller (e.g. from Mimo 740)"
737 depends on TOUCHSCREEN_USB_COMPOSITE
739 config TOUCHSCREEN_USB_ZYTRONIC
741 bool "Zytronic controller" if EXPERT
742 depends on TOUCHSCREEN_USB_COMPOSITE
744 config TOUCHSCREEN_USB_ETT_TC45USB
746 bool "ET&T USB series TC4UM/TC5UH touchscreen controller support" if EXPERT
747 depends on TOUCHSCREEN_USB_COMPOSITE
749 config TOUCHSCREEN_USB_NEXIO
751 bool "NEXIO/iNexio device support" if EXPERT
752 depends on TOUCHSCREEN_USB_COMPOSITE
754 config TOUCHSCREEN_USB_EASYTOUCH
756 bool "EasyTouch USB Touch controller device support" if EMBEDDED
757 depends on TOUCHSCREEN_USB_COMPOSITE
759 Say Y here if you have an EasyTouch USB Touch controller.
762 config TOUCHSCREEN_TOUCHIT213
763 tristate "Sahara TouchIT-213 touchscreen"
766 Say Y here if you have a Sahara TouchIT-213 Tablet PC.
770 To compile this driver as a module, choose M here: the
771 module will be called touchit213.
773 config TOUCHSCREEN_TSC_SERIO
774 tristate "TSC-10/25/40 serial touchscreen support"
777 Say Y here if you have a TSC-10, 25 or 40 serial touchscreen connected
782 To compile this driver as a module, choose M here: the
783 module will be called tsc40.
785 config TOUCHSCREEN_TSC2005
786 tristate "TSC2005 based touchscreens"
787 depends on SPI_MASTER && GENERIC_HARDIRQS
789 Say Y here if you have a TSC2005 based touchscreen.
793 To compile this driver as a module, choose M here: the
794 module will be called tsc2005.
796 config TOUCHSCREEN_TSC2007
797 tristate "TSC2007 based touchscreens"
800 Say Y here if you have a TSC2007 based touchscreen.
804 To compile this driver as a module, choose M here: the
805 module will be called tsc2007.
807 config TOUCHSCREEN_W90X900
808 tristate "W90P910 touchscreen driver"
811 Say Y here if you have a W90P910 based touchscreen.
813 To compile this driver as a module, choose M here: the
814 module will be called w90p910_ts.
816 config TOUCHSCREEN_PCAP
817 tristate "Motorola PCAP touchscreen"
820 Say Y here if you have a Motorola EZX telephone and
821 want to enable support for the built-in touchscreen.
823 To compile this driver as a module, choose M here: the
824 module will be called pcap_ts.
826 config TOUCHSCREEN_ST1232
827 tristate "Sitronix ST1232 touchscreen controllers"
830 Say Y here if you want to support Sitronix ST1232
831 touchscreen controller.
835 To compile this driver as a module, choose M here: the
836 module will be called st1232_ts.
838 config TOUCHSCREEN_STMPE
839 tristate "STMicroelectronics STMPE touchscreens"
842 Say Y here if you want support for STMicroelectronics
843 STMPE touchscreen controllers.
845 To compile this driver as a module, choose M here: the
846 module will be called stmpe-ts.
848 config TOUCHSCREEN_TPS6507X
849 tristate "TPS6507x based touchscreens"
852 Say Y here if you have a TPS6507x based touchscreen
857 To compile this driver as a module, choose M here: the
858 module will be called tps6507x_ts.