drivers/mmc/host/sdhci.c

   1 /*
   2  *  linux/drivers/mmc/host/sdhci.c - Secure Digital Host Controller Interface driver
   3  *
   4  *  Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved.
   5  *
   6  * This program is free software; you can redistribute it and/or modify
   7  * it under the terms of the GNU General Public License as published by
   8  * the Free Software Foundation; either version 2 of the License, or (at
   9  * your option) any later version.
  10  *
  11  * Thanks to the following companies for their support:
  12  *
  13  *     - JMicron (hardware and technical support)
  14  */
  15
  16 #include <linux/delay.h>
  17 #include <linux/highmem.h>
  18 #include <linux/io.h>
  19 #include <linux/dma-mapping.h>
  20 #include <linux/slab.h>
  21 #include <linux/scatterlist.h>
  22 #include <linux/regulator/consumer.h>
  23
  24 #include <linux/leds.h>
  25
  26 #include <linux/mmc/mmc.h>
  27 #include <linux/mmc/host.h>
  28
  29 #include "sdhci.h"
  30
  31 #define DRIVER_NAME "sdhci"
  32
  33 #define DBG(f, x...) \
  34         pr_debug(DRIVER_NAME " [%s()]: " f, __func__,## x)
  35
  36 #if defined(CONFIG_LEDS_CLASS) || (defined(CONFIG_LEDS_CLASS_MODULE) && \
  37         defined(CONFIG_MMC_SDHCI_MODULE))
  38 #define SDHCI_USE_LEDS_CLASS
  39 #endif
  40
  41 #define MAX_TUNING_LOOP 40
  42
  43 static unsigned int debug_quirks = 0;
  44
  45 static void sdhci_finish_data(struct sdhci_host *);
  46
  47 static void sdhci_send_command(struct sdhci_host *, struct mmc_command *);
  48 static void sdhci_finish_command(struct sdhci_host *);
  49 static int sdhci_execute_tuning(struct mmc_host *mmc);
  50 static void sdhci_tuning_timer(unsigned long data);
  51
  52 static void sdhci_dumpregs(struct sdhci_host *host)
  53 {
  54         printk(KERN_DEBUG DRIVER_NAME ": =========== REGISTER DUMP (%s)===========\n",
  55                 mmc_hostname(host->mmc));
  56
  57         printk(KERN_DEBUG DRIVER_NAME ": Sys addr: 0x%08x | Version:  0x%08x\n",
  58                 sdhci_readl(host, SDHCI_DMA_ADDRESS),
  59                 sdhci_readw(host, SDHCI_HOST_VERSION));
  60         printk(KERN_DEBUG DRIVER_NAME ": Blk size: 0x%08x | Blk cnt:  0x%08x\n",
  61                 sdhci_readw(host, SDHCI_BLOCK_SIZE),
  62                 sdhci_readw(host, SDHCI_BLOCK_COUNT));
  63         printk(KERN_DEBUG DRIVER_NAME ": Argument: 0x%08x | Trn mode: 0x%08x\n",
  64                 sdhci_readl(host, SDHCI_ARGUMENT),
  65                 sdhci_readw(host, SDHCI_TRANSFER_MODE));
  66         printk(KERN_DEBUG DRIVER_NAME ": Present:  0x%08x | Host ctl: 0x%08x\n",
  67                 sdhci_readl(host, SDHCI_PRESENT_STATE),
  68                 sdhci_readb(host, SDHCI_HOST_CONTROL));
  69         printk(KERN_DEBUG DRIVER_NAME ": Power:    0x%08x | Blk gap:  0x%08x\n",
  70                 sdhci_readb(host, SDHCI_POWER_CONTROL),
  71                 sdhci_readb(host, SDHCI_BLOCK_GAP_CONTROL));
  72         printk(KERN_DEBUG DRIVER_NAME ": Wake-up:  0x%08x | Clock:    0x%08x\n",
  73                 sdhci_readb(host, SDHCI_WAKE_UP_CONTROL),
  74                 sdhci_readw(host, SDHCI_CLOCK_CONTROL));
  75         printk(KERN_DEBUG DRIVER_NAME ": Timeout:  0x%08x | Int stat: 0x%08x\n",
  76                 sdhci_readb(host, SDHCI_TIMEOUT_CONTROL),
  77                 sdhci_readl(host, SDHCI_INT_STATUS));
  78         printk(KERN_DEBUG DRIVER_NAME ": Int enab: 0x%08x | Sig enab: 0x%08x\n",
  79                 sdhci_readl(host, SDHCI_INT_ENABLE),
  80                 sdhci_readl(host, SDHCI_SIGNAL_ENABLE));
  81         printk(KERN_DEBUG DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n",
  82                 sdhci_readw(host, SDHCI_ACMD12_ERR),
  83                 sdhci_readw(host, SDHCI_SLOT_INT_STATUS));
  84         printk(KERN_DEBUG DRIVER_NAME ": Caps:     0x%08x | Caps_1:   0x%08x\n",
  85                 sdhci_readl(host, SDHCI_CAPABILITIES),
  86                 sdhci_readl(host, SDHCI_CAPABILITIES_1));
  87         printk(KERN_DEBUG DRIVER_NAME ": Cmd:      0x%08x | Max curr: 0x%08x\n",
  88                 sdhci_readw(host, SDHCI_COMMAND),
  89                 sdhci_readl(host, SDHCI_MAX_CURRENT));
  90         printk(KERN_DEBUG DRIVER_NAME ": Host ctl2: 0x%08x\n",
  91                 sdhci_readw(host, SDHCI_HOST_CONTROL2));
  92
  93         if (host->flags & SDHCI_USE_ADMA)
  94                 printk(KERN_DEBUG DRIVER_NAME ": ADMA Err: 0x%08x | ADMA Ptr: 0x%08x\n",
  95                        readl(host->ioaddr + SDHCI_ADMA_ERROR),
  96                        readl(host->ioaddr + SDHCI_ADMA_ADDRESS));
  97
  98         printk(KERN_DEBUG DRIVER_NAME ": ===========================================\n");
  99 }
 100
 101 /*****************************************************************************\
 102  *                                                                           *
 103  * Low level functions                                                       *
 104  *                                                                           *
 105 \*****************************************************************************/
 106
 107 static void sdhci_clear_set_irqs(struct sdhci_host *host, u32 clear, u32 set)
 108 {
 109         u32 ier;
 110
 111         ier = sdhci_readl(host, SDHCI_INT_ENABLE);
 112         ier &= ~clear;
 113         ier |= set;
 114         sdhci_writel(host, ier, SDHCI_INT_ENABLE);
 115         sdhci_writel(host, ier, SDHCI_SIGNAL_ENABLE);
 116 }
 117
 118 static void sdhci_unmask_irqs(struct sdhci_host *host, u32 irqs)
 119 {
 120         sdhci_clear_set_irqs(host, 0, irqs);
 121 }
 122
 123 static void sdhci_mask_irqs(struct sdhci_host *host, u32 irqs)
 124 {
 125         sdhci_clear_set_irqs(host, irqs, 0);
 126 }
 127
 128 static void sdhci_set_card_detection(struct sdhci_host *host, bool enable)
 129 {
 130         u32 present, irqs;
 131
 132         if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
 133                 return;
 134
 135         present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
 136                               SDHCI_CARD_PRESENT;
 137         irqs = present ? SDHCI_INT_CARD_REMOVE : SDHCI_INT_CARD_INSERT;
 138
 139         if (enable)
 140                 sdhci_unmask_irqs(host, irqs);
 141         else
 142                 sdhci_mask_irqs(host, irqs);
 143 }
 144
 145 static void sdhci_enable_card_detection(struct sdhci_host *host)
 146 {
 147         sdhci_set_card_detection(host, true);
 148 }
 149
 150 static void sdhci_disable_card_detection(struct sdhci_host *host)
 151 {
 152         sdhci_set_card_detection(host, false);
 153 }
 154
 155 static void sdhci_reset(struct sdhci_host *host, u8 mask)
 156 {
 157         unsigned long timeout;
 158         u32 uninitialized_var(ier);
 159
 160         if (host->quirks & SDHCI_QUIRK_NO_CARD_NO_RESET) {
 161                 if (!(sdhci_readl(host, SDHCI_PRESENT_STATE) &
 162                         SDHCI_CARD_PRESENT))
 163                         return;
 164         }
 165
 166         if (host->quirks & SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET)
 167                 ier = sdhci_readl(host, SDHCI_INT_ENABLE);
 168
 169         if (host->ops->platform_reset_enter)
 170                 host->ops->platform_reset_enter(host, mask);
 171
 172         sdhci_writeb(host, mask, SDHCI_SOFTWARE_RESET);
 173
 174         if (mask & SDHCI_RESET_ALL)
 175                 host->clock = 0;
 176
 177         /* Wait max 100 ms */
 178         timeout = 100;
 179
 180         /* hw clears the bit when it's done */
 181         while (sdhci_readb(host, SDHCI_SOFTWARE_RESET) & mask) {
 182                 if (timeout == 0) {
 183                         printk(KERN_ERR "%s: Reset 0x%x never completed.\n",
 184                                 mmc_hostname(host->mmc), (int)mask);
 185                         sdhci_dumpregs(host);
 186                         return;
 187                 }
 188                 timeout--;
 189                 mdelay(1);
 190         }
 191
 192         if (host->ops->platform_reset_exit)
 193                 host->ops->platform_reset_exit(host, mask);
 194
 195         if (host->quirks & SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET)
 196                 sdhci_clear_set_irqs(host, SDHCI_INT_ALL_MASK, ier);
 197 }
 198
 199 static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios);
 200
 201 static void sdhci_init(struct sdhci_host *host, int soft)
 202 {
 203         if (soft)
 204                 sdhci_reset(host, SDHCI_RESET_CMD|SDHCI_RESET_DATA);
 205         else
 206                 sdhci_reset(host, SDHCI_RESET_ALL);
 207
 208         sdhci_clear_set_irqs(host, SDHCI_INT_ALL_MASK,
 209                 SDHCI_INT_BUS_POWER | SDHCI_INT_DATA_END_BIT |
 210                 SDHCI_INT_DATA_CRC | SDHCI_INT_DATA_TIMEOUT | SDHCI_INT_INDEX |
 211                 SDHCI_INT_END_BIT | SDHCI_INT_CRC | SDHCI_INT_TIMEOUT |
 212                 SDHCI_INT_DATA_END | SDHCI_INT_RESPONSE);
 213
 214         if (soft) {
 215                 /* force clock reconfiguration */
 216                 host->clock = 0;
 217                 sdhci_set_ios(host->mmc, &host->mmc->ios);
 218         }
 219 }
 220
 221 static void sdhci_reinit(struct sdhci_host *host)
 222 {
 223         sdhci_init(host, 0);
 224         sdhci_enable_card_detection(host);
 225 }
 226
 227 static void sdhci_activate_led(struct sdhci_host *host)
 228 {
 229         u8 ctrl;
 230
 231         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
 232         ctrl |= SDHCI_CTRL_LED;
 233         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
 234 }
 235
 236 static void sdhci_deactivate_led(struct sdhci_host *host)
 237 {
 238         u8 ctrl;
 239
 240         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
 241         ctrl &= ~SDHCI_CTRL_LED;
 242         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
 243 }
 244
 245 #ifdef SDHCI_USE_LEDS_CLASS
 246 static void sdhci_led_control(struct led_classdev *led,
 247         enum led_brightness brightness)
 248 {
 249         struct sdhci_host *host = container_of(led, struct sdhci_host, led);
 250         unsigned long flags;
 251
 252         spin_lock_irqsave(&host->lock, flags);
 253
 254         if (brightness == LED_OFF)
 255                 sdhci_deactivate_led(host);
 256         else
 257                 sdhci_activate_led(host);
 258
 259         spin_unlock_irqrestore(&host->lock, flags);
 260 }
 261 #endif
 262
 263 /*****************************************************************************\
 264  *                                                                           *
 265  * Core functions                                                            *
 266  *                                                                           *
 267 \*****************************************************************************/
 268
 269 static void sdhci_read_block_pio(struct sdhci_host *host)
 270 {
 271         unsigned long flags;
 272         size_t blksize, len, chunk;
 273         u32 uninitialized_var(scratch);
 274         u8 *buf;
 275
 276         DBG("PIO reading\n");
 277
 278         blksize = host->data->blksz;
 279         chunk = 0;
 280
 281         local_irq_save(flags);
 282
 283         while (blksize) {
 284                 if (!sg_miter_next(&host->sg_miter))
 285                         BUG();
 286
 287                 len = min(host->sg_miter.length, blksize);
 288
 289                 blksize -= len;
 290                 host->sg_miter.consumed = len;
 291
 292                 buf = host->sg_miter.addr;
 293
 294                 while (len) {
 295                         if (chunk == 0) {
 296                                 scratch = sdhci_readl(host, SDHCI_BUFFER);
 297                                 chunk = 4;
 298                         }
 299
 300                         *buf = scratch & 0xFF;
 301
 302                         buf++;
 303                         scratch >>= 8;
 304                         chunk--;
 305                         len--;
 306                 }
 307         }
 308
 309         sg_miter_stop(&host->sg_miter);
 310
 311         local_irq_restore(flags);
 312 }
 313
 314 static void sdhci_write_block_pio(struct sdhci_host *host)
 315 {
 316         unsigned long flags;
 317         size_t blksize, len, chunk;
 318         u32 scratch;
 319         u8 *buf;
 320
 321         DBG("PIO writing\n");
 322
 323         blksize = host->data->blksz;
 324         chunk = 0;
 325         scratch = 0;
 326
 327         local_irq_save(flags);
 328
 329         while (blksize) {
 330                 if (!sg_miter_next(&host->sg_miter))
 331                         BUG();
 332
 333                 len = min(host->sg_miter.length, blksize);
 334
 335                 blksize -= len;
 336                 host->sg_miter.consumed = len;
 337
 338                 buf = host->sg_miter.addr;
 339
 340                 while (len) {
 341                         scratch |= (u32)*buf << (chunk * 8);
 342
 343                         buf++;
 344                         chunk++;
 345                         len--;
 346
 347                         if ((chunk == 4) || ((len == 0) && (blksize == 0))) {
 348                                 sdhci_writel(host, scratch, SDHCI_BUFFER);
 349                                 chunk = 0;
 350                                 scratch = 0;
 351                         }
 352                 }
 353         }
 354
 355         sg_miter_stop(&host->sg_miter);
 356
 357         local_irq_restore(flags);
 358 }
 359
 360 static void sdhci_transfer_pio(struct sdhci_host *host)
 361 {
 362         u32 mask;
 363
 364         BUG_ON(!host->data);
 365
 366         if (host->blocks == 0)
 367                 return;
 368
 369         if (host->data->flags & MMC_DATA_READ)
 370                 mask = SDHCI_DATA_AVAILABLE;
 371         else
 372                 mask = SDHCI_SPACE_AVAILABLE;
 373
 374         /*
 375          * Some controllers (JMicron JMB38x) mess up the buffer bits
 376          * for transfers < 4 bytes. As long as it is just one block,
 377          * we can ignore the bits.
 378          */
 379         if ((host->quirks & SDHCI_QUIRK_BROKEN_SMALL_PIO) &&
 380                 (host->data->blocks == 1))
 381                 mask = ~0;
 382
 383         while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
 384                 if (host->quirks & SDHCI_QUIRK_PIO_NEEDS_DELAY)
 385                         udelay(100);
 386
 387                 if (host->data->flags & MMC_DATA_READ)
 388                         sdhci_read_block_pio(host);
 389                 else
 390                         sdhci_write_block_pio(host);
 391
 392                 host->blocks--;
 393                 if (host->blocks == 0)
 394                         break;
 395         }
 396
 397         DBG("PIO transfer complete.\n");
 398 }
 399
 400 static char *sdhci_kmap_atomic(struct scatterlist *sg, unsigned long *flags)
 401 {
 402         local_irq_save(*flags);
 403         return kmap_atomic(sg_page(sg), KM_BIO_SRC_IRQ) + sg->offset;
 404 }
 405
 406 static void sdhci_kunmap_atomic(void *buffer, unsigned long *flags)
 407 {
 408         kunmap_atomic(buffer, KM_BIO_SRC_IRQ);
 409         local_irq_restore(*flags);
 410 }
 411
 412 static void sdhci_set_adma_desc(u8 *desc, u32 addr, int len, unsigned cmd)
 413 {
 414         __le32 *dataddr = (__le32 __force *)(desc + 4);
 415         __le16 *cmdlen = (__le16 __force *)desc;
 416
 417         /* SDHCI specification says ADMA descriptors should be 4 byte
 418          * aligned, so using 16 or 32bit operations should be safe. */
 419
 420         cmdlen[0] = cpu_to_le16(cmd);
 421         cmdlen[1] = cpu_to_le16(len);
 422
 423         dataddr[0] = cpu_to_le32(addr);
 424 }
 425
 426 static int sdhci_adma_table_pre(struct sdhci_host *host,
 427         struct mmc_data *data)
 428 {
 429         int direction;
 430
 431         u8 *desc;
 432         u8 *align;
 433         dma_addr_t addr;
 434         dma_addr_t align_addr;
 435         int len, offset;
 436
 437         struct scatterlist *sg;
 438         int i;
 439         char *buffer;
 440         unsigned long flags;
 441
 442         /*
 443          * The spec does not specify endianness of descriptor table.
 444          * We currently guess that it is LE.
 445          */
 446
 447         if (data->flags & MMC_DATA_READ)
 448                 direction = DMA_FROM_DEVICE;
 449         else
 450                 direction = DMA_TO_DEVICE;
 451
 452         /*
 453          * The ADMA descriptor table is mapped further down as we
 454          * need to fill it with data first.
 455          */
 456
 457         host->align_addr = dma_map_single(mmc_dev(host->mmc),
 458                 host->align_buffer, 128 * 4, direction);
 459         if (dma_mapping_error(mmc_dev(host->mmc), host->align_addr))
 460                 goto fail;
 461         BUG_ON(host->align_addr & 0x3);
 462
 463         host->sg_count = dma_map_sg(mmc_dev(host->mmc),
 464                 data->sg, data->sg_len, direction);
 465         if (host->sg_count == 0)
 466                 goto unmap_align;
 467
 468         desc = host->adma_desc;
 469         align = host->align_buffer;
 470
 471         align_addr = host->align_addr;
 472
 473         for_each_sg(data->sg, sg, host->sg_count, i) {
 474                 addr = sg_dma_address(sg);
 475                 len = sg_dma_len(sg);
 476
 477                 /*
 478                  * The SDHCI specification states that ADMA
 479                  * addresses must be 32-bit aligned. If they
 480                  * aren't, then we use a bounce buffer for
 481                  * the (up to three) bytes that screw up the
 482                  * alignment.
 483                  */
 484                 offset = (4 - (addr & 0x3)) & 0x3;
 485                 if (offset) {
 486                         if (data->flags & MMC_DATA_WRITE) {
 487                                 buffer = sdhci_kmap_atomic(sg, &flags);
 488                                 WARN_ON(((long)buffer & PAGE_MASK) > (PAGE_SIZE - 3));
 489                                 memcpy(align, buffer, offset);
 490                                 sdhci_kunmap_atomic(buffer, &flags);
 491                         }
 492
 493                         /* tran, valid */
 494                         sdhci_set_adma_desc(desc, align_addr, offset, 0x21);
 495
 496                         BUG_ON(offset > 65536);
 497
 498                         align += 4;
 499                         align_addr += 4;
 500
 501                         desc += 8;
 502
 503                         addr += offset;
 504                         len -= offset;
 505                 }
 506
 507                 BUG_ON(len > 65536);
 508
 509                 /* tran, valid */
 510                 sdhci_set_adma_desc(desc, addr, len, 0x21);
 511                 desc += 8;
 512
 513                 /*
 514                  * If this triggers then we have a calculation bug
 515                  * somewhere. :/
 516                  */
 517                 WARN_ON((desc - host->adma_desc) > (128 * 2 + 1) * 4);
 518         }
 519
 520         if (host->quirks & SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC) {
 521                 /*
 522                 * Mark the last descriptor as the terminating descriptor
 523                 */
 524                 if (desc != host->adma_desc) {
 525                         desc -= 8;
 526                         desc[0] |= 0x2; /* end */
 527                 }
 528         } else {
 529                 /*
 530                 * Add a terminating entry.
 531                 */
 532
 533                 /* nop, end, valid */
 534                 sdhci_set_adma_desc(desc, 0, 0, 0x3);
 535         }
 536
 537         /*
 538          * Resync align buffer as we might have changed it.
 539          */
 540         if (data->flags & MMC_DATA_WRITE) {
 541                 dma_sync_single_for_device(mmc_dev(host->mmc),
 542                         host->align_addr, 128 * 4, direction);
 543         }
 544
 545         host->adma_addr = dma_map_single(mmc_dev(host->mmc),
 546                 host->adma_desc, (128 * 2 + 1) * 4, DMA_TO_DEVICE);
 547         if (dma_mapping_error(mmc_dev(host->mmc), host->adma_addr))
 548                 goto unmap_entries;
 549         BUG_ON(host->adma_addr & 0x3);
 550
 551         return 0;
 552
 553 unmap_entries:
 554         dma_unmap_sg(mmc_dev(host->mmc), data->sg,
 555                 data->sg_len, direction);
 556 unmap_align:
 557         dma_unmap_single(mmc_dev(host->mmc), host->align_addr,
 558                 128 * 4, direction);
 559 fail:
 560         return -EINVAL;
 561 }
 562
 563 static void sdhci_adma_table_post(struct sdhci_host *host,
 564         struct mmc_data *data)
 565 {
 566         int direction;
 567
 568         struct scatterlist *sg;
 569         int i, size;
 570         u8 *align;
 571         char *buffer;
 572         unsigned long flags;
 573
 574         if (data->flags & MMC_DATA_READ)
 575                 direction = DMA_FROM_DEVICE;
 576         else
 577                 direction = DMA_TO_DEVICE;
 578
 579         dma_unmap_single(mmc_dev(host->mmc), host->adma_addr,
 580                 (128 * 2 + 1) * 4, DMA_TO_DEVICE);
 581
 582         dma_unmap_single(mmc_dev(host->mmc), host->align_addr,
 583                 128 * 4, direction);
 584
 585         if (data->flags & MMC_DATA_READ) {
 586                 dma_sync_sg_for_cpu(mmc_dev(host->mmc), data->sg,
 587                         data->sg_len, direction);
 588
 589                 align = host->align_buffer;
 590
 591                 for_each_sg(data->sg, sg, host->sg_count, i) {
 592                         if (sg_dma_address(sg) & 0x3) {
 593                                 size = 4 - (sg_dma_address(sg) & 0x3);
 594
 595                                 buffer = sdhci_kmap_atomic(sg, &flags);
 596                                 WARN_ON(((long)buffer & PAGE_MASK) > (PAGE_SIZE - 3));
 597                                 memcpy(buffer, align, size);
 598                                 sdhci_kunmap_atomic(buffer, &flags);
 599
 600                                 align += 4;
 601                         }
 602                 }
 603         }
 604
 605         dma_unmap_sg(mmc_dev(host->mmc), data->sg,
 606                 data->sg_len, direction);
 607 }
 608
 609 static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd)
 610 {
 611         u8 count;
 612         struct mmc_data *data = cmd->data;
 613         unsigned target_timeout, current_timeout;
 614
 615         /*
 616          * If the host controller provides us with an incorrect timeout
 617          * value, just skip the check and use 0xE.  The hardware may take
 618          * longer to time out, but that's much better than having a too-short
 619          * timeout value.
 620          */
 621         if (host->quirks & SDHCI_QUIRK_BROKEN_TIMEOUT_VAL)
 622                 return 0xE;
 623
 624         /* Unspecified timeout, assume max */
 625         if (!data && !cmd->cmd_timeout_ms)
 626                 return 0xE;
 627
 628         /* timeout in us */
 629         if (!data)
 630                 target_timeout = cmd->cmd_timeout_ms * 1000;
 631         else
 632                 target_timeout = data->timeout_ns / 1000 +
 633                         data->timeout_clks / host->clock;
 634
 635         /*
 636          * Figure out needed cycles.
 637          * We do this in steps in order to fit inside a 32 bit int.
 638          * The first step is the minimum timeout, which will have a
 639          * minimum resolution of 6 bits:
 640          * (1) 2^13*1000 > 2^22,
 641          * (2) host->timeout_clk < 2^16
 642          *     =>
 643          *     (1) / (2) > 2^6
 644          */
 645         count = 0;
 646         current_timeout = (1 << 13) * 1000 / host->timeout_clk;
 647         while (current_timeout < target_timeout) {
 648                 count++;
 649                 current_timeout <<= 1;
 650                 if (count >= 0xF)
 651                         break;
 652         }
 653
 654         if (count >= 0xF) {
 655                 printk(KERN_WARNING "%s: Too large timeout requested for CMD%d!\n",
 656                        mmc_hostname(host->mmc), cmd->opcode);
 657                 count = 0xE;
 658         }
 659
 660         return count;
 661 }
 662
 663 static void sdhci_set_transfer_irqs(struct sdhci_host *host)
 664 {
 665         u32 pio_irqs = SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL;
 666         u32 dma_irqs = SDHCI_INT_DMA_END | SDHCI_INT_ADMA_ERROR;
 667
 668         if (host->flags & SDHCI_REQ_USE_DMA)
 669                 sdhci_clear_set_irqs(host, pio_irqs, dma_irqs);
 670         else
 671                 sdhci_clear_set_irqs(host, dma_irqs, pio_irqs);
 672 }
 673
 674 static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
 675 {
 676         u8 count;
 677         u8 ctrl;
 678         struct mmc_data *data = cmd->data;
 679         int ret;
 680
 681         WARN_ON(host->data);
 682
 683         if (data || (cmd->flags & MMC_RSP_BUSY)) {
 684                 count = sdhci_calc_timeout(host, cmd);
 685                 sdhci_writeb(host, count, SDHCI_TIMEOUT_CONTROL);
 686         }
 687
 688         if (!data)
 689                 return;
 690
 691         /* Sanity checks */
 692         BUG_ON(data->blksz * data->blocks > 524288);
 693         BUG_ON(data->blksz > host->mmc->max_blk_size);
 694         BUG_ON(data->blocks > 65535);
 695
 696         host->data = data;
 697         host->data_early = 0;
 698         host->data->bytes_xfered = 0;
 699
 700         if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA))
 701                 host->flags |= SDHCI_REQ_USE_DMA;
 702
 703         /*
 704          * FIXME: This doesn't account for merging when mapping the
 705          * scatterlist.
 706          */
 707         if (host->flags & SDHCI_REQ_USE_DMA) {
 708                 int broken, i;
 709                 struct scatterlist *sg;
 710
 711                 broken = 0;
 712                 if (host->flags & SDHCI_USE_ADMA) {
 713                         if (host->quirks & SDHCI_QUIRK_32BIT_ADMA_SIZE)
 714                                 broken = 1;
 715                 } else {
 716                         if (host->quirks & SDHCI_QUIRK_32BIT_DMA_SIZE)
 717                                 broken = 1;
 718                 }
 719
 720                 if (unlikely(broken)) {
 721                         for_each_sg(data->sg, sg, data->sg_len, i) {
 722                                 if (sg->length & 0x3) {
 723                                         DBG("Reverting to PIO because of "
 724                                                 "transfer size (%d)\n",
 725                                                 sg->length);
 726                                         host->flags &= ~SDHCI_REQ_USE_DMA;
 727                                         break;
 728                                 }
 729                         }
 730                 }
 731         }
 732
 733         /*
 734          * The assumption here being that alignment is the same after
 735          * translation to device address space.
 736          */
 737         if (host->flags & SDHCI_REQ_USE_DMA) {
 738                 int broken, i;
 739                 struct scatterlist *sg;
 740
 741                 broken = 0;
 742                 if (host->flags & SDHCI_USE_ADMA) {
 743                         /*
 744                          * As we use 3 byte chunks to work around
 745                          * alignment problems, we need to check this
 746                          * quirk.
 747                          */
 748                         if (host->quirks & SDHCI_QUIRK_32BIT_ADMA_SIZE)
 749                                 broken = 1;
 750                 } else {
 751                         if (host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR)
 752                                 broken = 1;
 753                 }
 754
 755                 if (unlikely(broken)) {
 756                         for_each_sg(data->sg, sg, data->sg_len, i) {
 757                                 if (sg->offset & 0x3) {
 758                                         DBG("Reverting to PIO because of "
 759                                                 "bad alignment\n");
 760                                         host->flags &= ~SDHCI_REQ_USE_DMA;
 761                                         break;
 762                                 }
 763                         }
 764                 }
 765         }
 766
 767         if (host->flags & SDHCI_REQ_USE_DMA) {
 768                 if (host->flags & SDHCI_USE_ADMA) {
 769                         ret = sdhci_adma_table_pre(host, data);
 770                         if (ret) {
 771                                 /*
 772                                  * This only happens when someone fed
 773                                  * us an invalid request.
 774                                  */
 775                                 WARN_ON(1);
 776                                 host->flags &= ~SDHCI_REQ_USE_DMA;
 777                         } else {
 778                                 sdhci_writel(host, host->adma_addr,
 779                                         SDHCI_ADMA_ADDRESS);
 780                         }
 781                 } else {
 782                         int sg_cnt;
 783
 784                         sg_cnt = dma_map_sg(mmc_dev(host->mmc),
 785                                         data->sg, data->sg_len,
 786                                         (data->flags & MMC_DATA_READ) ?
 787                                                 DMA_FROM_DEVICE :
 788                                                 DMA_TO_DEVICE);
 789                         if (sg_cnt == 0) {
 790                                 /*
 791                                  * This only happens when someone fed
 792                                  * us an invalid request.
 793                                  */
 794                                 WARN_ON(1);
 795                                 host->flags &= ~SDHCI_REQ_USE_DMA;
 796                         } else {
 797                                 WARN_ON(sg_cnt != 1);
 798                                 sdhci_writel(host, sg_dma_address(data->sg),
 799                                         SDHCI_DMA_ADDRESS);
 800                         }
 801                 }
 802         }
 803
 804         /*
 805          * Always adjust the DMA selection as some controllers
 806          * (e.g. JMicron) can't do PIO properly when the selection
 807          * is ADMA.
 808          */
 809         if (host->version >= SDHCI_SPEC_200) {
 810                 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
 811                 ctrl &= ~SDHCI_CTRL_DMA_MASK;
 812                 if ((host->flags & SDHCI_REQ_USE_DMA) &&
 813                         (host->flags & SDHCI_USE_ADMA))
 814                         ctrl |= SDHCI_CTRL_ADMA32;
 815                 else
 816                         ctrl |= SDHCI_CTRL_SDMA;
 817                 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
 818         }
 819
 820         if (!(host->flags & SDHCI_REQ_USE_DMA)) {
 821                 int flags;
 822
 823                 flags = SG_MITER_ATOMIC;
 824                 if (host->data->flags & MMC_DATA_READ)
 825                         flags |= SG_MITER_TO_SG;
 826                 else
 827                         flags |= SG_MITER_FROM_SG;
 828                 sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
 829                 host->blocks = data->blocks;
 830         }
 831
 832         sdhci_set_transfer_irqs(host);
 833
 834         /* Set the DMA boundary value and block size */
 835         sdhci_writew(host, SDHCI_MAKE_BLKSZ(SDHCI_DEFAULT_BOUNDARY_ARG,
 836                 data->blksz), SDHCI_BLOCK_SIZE);
 837         sdhci_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
 838 }
 839
 840 static void sdhci_set_transfer_mode(struct sdhci_host *host,
 841         struct mmc_command *cmd)
 842 {
 843         u16 mode;
 844         struct mmc_data *data = cmd->data;
 845
 846         if (data == NULL)
 847                 return;
 848
 849         WARN_ON(!host->data);
 850
 851         mode = SDHCI_TRNS_BLK_CNT_EN;
 852         if (mmc_op_multi(cmd->opcode) || data->blocks > 1) {
 853                 mode |= SDHCI_TRNS_MULTI;
 854                 /*
 855                  * If we are sending CMD23, CMD12 never gets sent
 856                  * on successful completion (so no Auto-CMD12).
 857                  */
 858                 if (!host->mrq->sbc && (host->flags & SDHCI_AUTO_CMD12))
 859                         mode |= SDHCI_TRNS_AUTO_CMD12;
 860                 else if (host->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) {
 861                         mode |= SDHCI_TRNS_AUTO_CMD23;
 862                         sdhci_writel(host, host->mrq->sbc->arg, SDHCI_ARGUMENT2);
 863                 }
 864         }
 865
 866         if (data->flags & MMC_DATA_READ)
 867                 mode |= SDHCI_TRNS_READ;
 868         if (host->flags & SDHCI_REQ_USE_DMA)
 869                 mode |= SDHCI_TRNS_DMA;
 870
 871         sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
 872 }
 873
 874 static void sdhci_finish_data(struct sdhci_host *host)
 875 {
 876         struct mmc_data *data;
 877
 878         BUG_ON(!host->data);
 879
 880         data = host->data;
 881         host->data = NULL;
 882
 883         if (host->flags & SDHCI_REQ_USE_DMA) {
 884                 if (host->flags & SDHCI_USE_ADMA)
 885                         sdhci_adma_table_post(host, data);
 886                 else {
 887                         dma_unmap_sg(mmc_dev(host->mmc), data->sg,
 888                                 data->sg_len, (data->flags & MMC_DATA_READ) ?
 889                                         DMA_FROM_DEVICE : DMA_TO_DEVICE);
 890                 }
 891         }
 892
 893         /*
 894          * The specification states that the block count register must
 895          * be updated, but it does not specify at what point in the
 896          * data flow. That makes the register entirely useless to read
 897          * back so we have to assume that nothing made it to the card
 898          * in the event of an error.
 899          */
 900         if (data->error)
 901                 data->bytes_xfered = 0;
 902         else
 903                 data->bytes_xfered = data->blksz * data->blocks;
 904
 905         /*
 906          * Need to send CMD12 if -
 907          * a) open-ended multiblock transfer (no CMD23)
 908          * b) error in multiblock transfer
 909          */
 910         if (data->stop &&
 911             (data->error ||
 912              !host->mrq->sbc)) {
 913
 914                 /*
 915                  * The controller needs a reset of internal state machines
 916                  * upon error conditions.
 917                  */
 918                 if (data->error) {
 919                         sdhci_reset(host, SDHCI_RESET_CMD);
 920                         sdhci_reset(host, SDHCI_RESET_DATA);
 921                 }
 922
 923                 sdhci_send_command(host, data->stop);
 924         } else
 925                 tasklet_schedule(&host->finish_tasklet);
 926 }
 927
 928 static void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
 929 {
 930         int flags;
 931         u32 mask;
 932         unsigned long timeout;
 933
 934         WARN_ON(host->cmd);
 935
 936         /* Wait max 10 ms */
 937         timeout = 10;
 938
 939         mask = SDHCI_CMD_INHIBIT;
 940         if ((cmd->data != NULL) || (cmd->flags & MMC_RSP_BUSY))
 941                 mask |= SDHCI_DATA_INHIBIT;
 942
 943         /* We shouldn't wait for data inihibit for stop commands, even
 944            though they might use busy signaling */
 945         if (host->mrq->data && (cmd == host->mrq->data->stop))
 946                 mask &= ~SDHCI_DATA_INHIBIT;
 947
 948         while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
 949                 if (timeout == 0) {
 950                         printk(KERN_ERR "%s: Controller never released "
 951                                 "inhibit bit(s).\n", mmc_hostname(host->mmc));
 952                         sdhci_dumpregs(host);
 953                         cmd->error = -EIO;
 954                         tasklet_schedule(&host->finish_tasklet);
 955                         return;
 956                 }
 957                 timeout--;
 958                 mdelay(1);
 959         }
 960
 961         mod_timer(&host->timer, jiffies + 10 * HZ);
 962
 963         host->cmd = cmd;
 964
 965         sdhci_prepare_data(host, cmd);
 966
 967         sdhci_writel(host, cmd->arg, SDHCI_ARGUMENT);
 968
 969         sdhci_set_transfer_mode(host, cmd);
 970
 971         if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) {
 972                 printk(KERN_ERR "%s: Unsupported response type!\n",
 973                         mmc_hostname(host->mmc));
 974                 cmd->error = -EINVAL;
 975                 tasklet_schedule(&host->finish_tasklet);
 976                 return;
 977         }
 978
 979         if (!(cmd->flags & MMC_RSP_PRESENT))
 980                 flags = SDHCI_CMD_RESP_NONE;
 981         else if (cmd->flags & MMC_RSP_136)
 982                 flags = SDHCI_CMD_RESP_LONG;
 983         else if (cmd->flags & MMC_RSP_BUSY)
 984                 flags = SDHCI_CMD_RESP_SHORT_BUSY;
 985         else
 986                 flags = SDHCI_CMD_RESP_SHORT;
 987
 988         if (cmd->flags & MMC_RSP_CRC)
 989                 flags |= SDHCI_CMD_CRC;
 990         if (cmd->flags & MMC_RSP_OPCODE)
 991                 flags |= SDHCI_CMD_INDEX;
 992
 993         /* CMD19 is special in that the Data Present Select should be set */
 994         if (cmd->data || (cmd->opcode == MMC_SEND_TUNING_BLOCK))
 995                 flags |= SDHCI_CMD_DATA;
 996
 997         sdhci_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), SDHCI_COMMAND);
 998 }
 999
1000 static void sdhci_finish_command(struct sdhci_host *host)
1001 {
1002         int i;
1003
1004         BUG_ON(host->cmd == NULL);
1005
1006         if (host->cmd->flags & MMC_RSP_PRESENT) {
1007                 if (host->cmd->flags & MMC_RSP_136) {
1008                         /* CRC is stripped so we need to do some shifting. */
1009                         for (i = 0;i < 4;i++) {
1010                                 host->cmd->resp[i] = sdhci_readl(host,
1011                                         SDHCI_RESPONSE + (3-i)*4) << 8;
1012                                 if (i != 3)
1013                                         host->cmd->resp[i] |=
1014                                                 sdhci_readb(host,
1015                                                 SDHCI_RESPONSE + (3-i)*4-1);
1016                         }
1017                 } else {
1018                         host->cmd->resp[0] = sdhci_readl(host, SDHCI_RESPONSE);
1019                 }
1020         }
1021
1022         host->cmd->error = 0;
1023
1024         /* Finished CMD23, now send actual command. */
1025         if (host->cmd == host->mrq->sbc) {
1026                 host->cmd = NULL;
1027                 sdhci_send_command(host, host->mrq->cmd);
1028         } else {
1029
1030                 /* Processed actual command. */
1031                 if (host->data && host->data_early)
1032                         sdhci_finish_data(host);
1033
1034                 if (!host->cmd->data)
1035                         tasklet_schedule(&host->finish_tasklet);
1036
1037                 host->cmd = NULL;
1038         }
1039 }
1040
1041 static void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
1042 {
1043         int div = 0; /* Initialized for compiler warning */
1044         u16 clk = 0;
1045         unsigned long timeout;
1046
1047         if (clock == host->clock)
1048                 return;
1049
1050         if (host->ops->set_clock) {
1051                 host->ops->set_clock(host, clock);
1052                 if (host->quirks & SDHCI_QUIRK_NONSTANDARD_CLOCK)
1053                         return;
1054         }
1055
1056         sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
1057
1058         if (clock == 0)
1059                 goto out;
1060
1061         if (host->version >= SDHCI_SPEC_300) {
1062                 /*
1063                  * Check if the Host Controller supports Programmable Clock
1064                  * Mode.
1065                  */
1066                 if (host->clk_mul) {
1067                         u16 ctrl;
1068
1069                         /*
1070                          * We need to figure out whether the Host Driver needs
1071                          * to select Programmable Clock Mode, or the value can
1072                          * be set automatically by the Host Controller based on
1073                          * the Preset Value registers.
1074                          */
1075                         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1076                         if (!(ctrl & SDHCI_CTRL_PRESET_VAL_ENABLE)) {
1077                                 for (div = 1; div <= 1024; div++) {
1078                                         if (((host->max_clk * host->clk_mul) /
1079                                               div) <= clock)
1080                                                 break;
1081                                 }
1082                                 /*
1083                                  * Set Programmable Clock Mode in the Clock
1084                                  * Control register.
1085                                  */
1086                                 clk = SDHCI_PROG_CLOCK_MODE;
1087                                 div--;
1088                         }
1089                 } else {
1090                         /* Version 3.00 divisors must be a multiple of 2. */
1091                         if (host->max_clk <= clock)
1092                                 div = 1;
1093                         else {
1094                                 for (div = 2; div < SDHCI_MAX_DIV_SPEC_300;
1095                                      div += 2) {
1096                                         if ((host->max_clk / div) <= clock)
1097                                                 break;
1098                                 }
1099                         }
1100                         div >>= 1;
1101                 }
1102         } else {
1103                 /* Version 2.00 divisors must be a power of 2. */
1104                 for (div = 1; div < SDHCI_MAX_DIV_SPEC_200; div *= 2) {
1105                         if ((host->max_clk / div) <= clock)
1106                                 break;
1107                 }
1108                 div >>= 1;
1109         }
1110
1111         clk |= (div & SDHCI_DIV_MASK) << SDHCI_DIVIDER_SHIFT;
1112         clk |= ((div & SDHCI_DIV_HI_MASK) >> SDHCI_DIV_MASK_LEN)
1113                 << SDHCI_DIVIDER_HI_SHIFT;
1114         clk |= SDHCI_CLOCK_INT_EN;
1115         sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1116
1117         /* Wait max 20 ms */
1118         timeout = 20;
1119         while (!((clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL))
1120                 & SDHCI_CLOCK_INT_STABLE)) {
1121                 if (timeout == 0) {
1122                         printk(KERN_ERR "%s: Internal clock never "
1123                                 "stabilised.\n", mmc_hostname(host->mmc));
1124                         sdhci_dumpregs(host);
1125                         return;
1126                 }
1127                 timeout--;
1128                 mdelay(1);
1129         }
1130
1131         clk |= SDHCI_CLOCK_CARD_EN;
1132         sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1133
1134 out:
1135         host->clock = clock;
1136 }
1137
1138 static void sdhci_set_power(struct sdhci_host *host, unsigned short power)
1139 {
1140         u8 pwr = 0;
1141
1142         if (power != (unsigned short)-1) {
1143                 switch (1 << power) {
1144                 case MMC_VDD_165_195:
1145                         pwr = SDHCI_POWER_180;
1146                         break;
1147                 case MMC_VDD_29_30:
1148                 case MMC_VDD_30_31:
1149                         pwr = SDHCI_POWER_300;
1150                         break;
1151                 case MMC_VDD_32_33:
1152                 case MMC_VDD_33_34:
1153                         pwr = SDHCI_POWER_330;
1154                         break;
1155                 default:
1156                         BUG();
1157                 }
1158         }
1159
1160         if (host->pwr == pwr)
1161                 return;
1162
1163         host->pwr = pwr;
1164
1165         if (pwr == 0) {
1166                 sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
1167                 return;
1168         }
1169
1170         /*
1171          * Spec says that we should clear the power reg before setting
1172          * a new value. Some controllers don't seem to like this though.
1173          */
1174         if (!(host->quirks & SDHCI_QUIRK_SINGLE_POWER_WRITE))
1175                 sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
1176
1177         /*
1178          * At least the Marvell CaFe chip gets confused if we set the voltage
1179          * and set turn on power at the same time, so set the voltage first.
1180          */
1181         if (host->quirks & SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER)
1182                 sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
1183
1184         pwr |= SDHCI_POWER_ON;
1185
1186         sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
1187
1188         /*
1189          * Some controllers need an extra 10ms delay of 10ms before they
1190          * can apply clock after applying power
1191          */
1192         if (host->quirks & SDHCI_QUIRK_DELAY_AFTER_POWER)
1193                 mdelay(10);
1194 }
1195
1196 /*****************************************************************************\
1197  *                                                                           *
1198  * MMC callbacks                                                             *
1199  *                                                                           *
1200 \*****************************************************************************/
1201
1202 static void sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq)
1203 {
1204         struct sdhci_host *host;
1205         bool present;
1206         unsigned long flags;
1207
1208         host = mmc_priv(mmc);
1209
1210         spin_lock_irqsave(&host->lock, flags);
1211
1212         WARN_ON(host->mrq != NULL);
1213
1214 #ifndef SDHCI_USE_LEDS_CLASS
1215         sdhci_activate_led(host);
1216 #endif
1217
1218         /*
1219          * Ensure we don't send the STOP for non-SET_BLOCK_COUNTED
1220          * requests if Auto-CMD12 is enabled.
1221          */
1222         if (!mrq->sbc && (host->flags & SDHCI_AUTO_CMD12)) {
1223                 if (mrq->stop) {
1224                         mrq->data->stop = NULL;
1225                         mrq->stop = NULL;
1226                 }
1227         }
1228
1229         host->mrq = mrq;
1230
1231         /* If polling, assume that the card is always present. */
1232         if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
1233                 present = true;
1234         else
1235                 present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
1236                                 SDHCI_CARD_PRESENT;
1237
1238         if (!present || host->flags & SDHCI_DEVICE_DEAD) {
1239                 host->mrq->cmd->error = -ENOMEDIUM;
1240                 tasklet_schedule(&host->finish_tasklet);
1241         } else {
1242                 u32 present_state;
1243
1244                 present_state = sdhci_readl(host, SDHCI_PRESENT_STATE);
1245                 /*
1246                  * Check if the re-tuning timer has already expired and there
1247                  * is no on-going data transfer. If so, we need to execute
1248                  * tuning procedure before sending command.
1249                  */
1250                 if ((host->flags & SDHCI_NEEDS_RETUNING) &&
1251                     !(present_state & (SDHCI_DOING_WRITE | SDHCI_DOING_READ))) {
1252                         spin_unlock_irqrestore(&host->lock, flags);
1253                         sdhci_execute_tuning(mmc);
1254                         spin_lock_irqsave(&host->lock, flags);
1255
1256                         /* Restore original mmc_request structure */
1257                         host->mrq = mrq;
1258                 }
1259
1260                 if (mrq->sbc && !(host->flags & SDHCI_AUTO_CMD23))
1261                         sdhci_send_command(host, mrq->sbc);
1262                 else
1263                         sdhci_send_command(host, mrq->cmd);
1264         }
1265
1266         mmiowb();
1267         spin_unlock_irqrestore(&host->lock, flags);
1268 }
1269
1270 static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1271 {
1272         struct sdhci_host *host;
1273         unsigned long flags;
1274         u8 ctrl;
1275
1276         host = mmc_priv(mmc);
1277
1278         spin_lock_irqsave(&host->lock, flags);
1279
1280         if (host->flags & SDHCI_DEVICE_DEAD)
1281                 goto out;
1282
1283         /*
1284          * Reset the chip on each power off.
1285          * Should clear out any weird states.
1286          */
1287         if (ios->power_mode == MMC_POWER_OFF) {
1288                 sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
1289                 sdhci_reinit(host);
1290         }
1291
1292         sdhci_set_clock(host, ios->clock);
1293
1294         if (ios->power_mode == MMC_POWER_OFF)
1295                 sdhci_set_power(host, -1);
1296         else
1297                 sdhci_set_power(host, ios->vdd);
1298
1299         if (host->ops->platform_send_init_74_clocks)
1300                 host->ops->platform_send_init_74_clocks(host, ios->power_mode);
1301
1302         /*
1303          * If your platform has 8-bit width support but is not a v3 controller,
1304          * or if it requires special setup code, you should implement that in
1305          * platform_8bit_width().
1306          */
1307         if (host->ops->platform_8bit_width)
1308                 host->ops->platform_8bit_width(host, ios->bus_width);
1309         else {
1310                 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
1311                 if (ios->bus_width == MMC_BUS_WIDTH_8) {
1312                         ctrl &= ~SDHCI_CTRL_4BITBUS;
1313                         if (host->version >= SDHCI_SPEC_300)
1314                                 ctrl |= SDHCI_CTRL_8BITBUS;
1315                 } else {
1316                         if (host->version >= SDHCI_SPEC_300)
1317                                 ctrl &= ~SDHCI_CTRL_8BITBUS;
1318                         if (ios->bus_width == MMC_BUS_WIDTH_4)
1319                                 ctrl |= SDHCI_CTRL_4BITBUS;
1320                         else
1321                                 ctrl &= ~SDHCI_CTRL_4BITBUS;
1322                 }
1323                 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1324         }
1325
1326         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
1327
1328         if ((ios->timing == MMC_TIMING_SD_HS ||
1329              ios->timing == MMC_TIMING_MMC_HS)
1330             && !(host->quirks & SDHCI_QUIRK_NO_HISPD_BIT))
1331                 ctrl |= SDHCI_CTRL_HISPD;
1332         else
1333                 ctrl &= ~SDHCI_CTRL_HISPD;
1334
1335         if (host->version >= SDHCI_SPEC_300) {
1336                 u16 clk, ctrl_2;
1337                 unsigned int clock;
1338
1339                 /* In case of UHS-I modes, set High Speed Enable */
1340                 if ((ios->timing == MMC_TIMING_UHS_SDR50) ||
1341                     (ios->timing == MMC_TIMING_UHS_SDR104) ||
1342                     (ios->timing == MMC_TIMING_UHS_DDR50) ||
1343                     (ios->timing == MMC_TIMING_UHS_SDR25) ||
1344                     (ios->timing == MMC_TIMING_UHS_SDR12))
1345                         ctrl |= SDHCI_CTRL_HISPD;
1346
1347                 ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1348                 if (!(ctrl_2 & SDHCI_CTRL_PRESET_VAL_ENABLE)) {
1349                         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1350                         /*
1351                          * We only need to set Driver Strength if the
1352                          * preset value enable is not set.
1353                          */
1354                         ctrl_2 &= ~SDHCI_CTRL_DRV_TYPE_MASK;
1355                         if (ios->drv_type == MMC_SET_DRIVER_TYPE_A)
1356                                 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_A;
1357                         else if (ios->drv_type == MMC_SET_DRIVER_TYPE_C)
1358                                 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_C;
1359
1360                         sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
1361                 } else {
1362                         /*
1363                          * According to SDHC Spec v3.00, if the Preset Value
1364                          * Enable in the Host Control 2 register is set, we
1365                          * need to reset SD Clock Enable before changing High
1366                          * Speed Enable to avoid generating clock gliches.
1367                          */
1368
1369                         /* Reset SD Clock Enable */
1370                         clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1371                         clk &= ~SDHCI_CLOCK_CARD_EN;
1372                         sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1373
1374                         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1375
1376                         /* Re-enable SD Clock */
1377                         clock = host->clock;
1378                         host->clock = 0;
1379                         sdhci_set_clock(host, clock);
1380                 }
1381
1382
1383                 /* Reset SD Clock Enable */
1384                 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1385                 clk &= ~SDHCI_CLOCK_CARD_EN;
1386                 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1387
1388                 if (host->ops->set_uhs_signaling)
1389                         host->ops->set_uhs_signaling(host, ios->timing);
1390                 else {
1391                         ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1392                         /* Select Bus Speed Mode for host */
1393                         ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
1394                         if (ios->timing == MMC_TIMING_UHS_SDR12)
1395                                 ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
1396                         else if (ios->timing == MMC_TIMING_UHS_SDR25)
1397                                 ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
1398                         else if (ios->timing == MMC_TIMING_UHS_SDR50)
1399                                 ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
1400                         else if (ios->timing == MMC_TIMING_UHS_SDR104)
1401                                 ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
1402                         else if (ios->timing == MMC_TIMING_UHS_DDR50)
1403                                 ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
1404                         sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
1405                 }
1406
1407                 /* Re-enable SD Clock */
1408                 clock = host->clock;
1409                 host->clock = 0;
1410                 sdhci_set_clock(host, clock);
1411         } else
1412                 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1413
1414         /*
1415          * Some (ENE) controllers go apeshit on some ios operation,
1416          * signalling timeout and CRC errors even on CMD0. Resetting
1417          * it on each ios seems to solve the problem.
1418          */
1419         if(host->quirks & SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS)
1420                 sdhci_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
1421
1422 out:
1423         mmiowb();
1424         spin_unlock_irqrestore(&host->lock, flags);
1425 }
1426
1427 static int check_ro(struct sdhci_host *host)
1428 {
1429         unsigned long flags;
1430         int is_readonly;
1431
1432         spin_lock_irqsave(&host->lock, flags);
1433
1434         if (host->flags & SDHCI_DEVICE_DEAD)
1435                 is_readonly = 0;
1436         else if (host->ops->get_ro)
1437                 is_readonly = host->ops->get_ro(host);
1438         else
1439                 is_readonly = !(sdhci_readl(host, SDHCI_PRESENT_STATE)
1440                                 & SDHCI_WRITE_PROTECT);
1441
1442         spin_unlock_irqrestore(&host->lock, flags);
1443
1444         /* This quirk needs to be replaced by a callback-function later */
1445         return host->quirks & SDHCI_QUIRK_INVERTED_WRITE_PROTECT ?
1446                 !is_readonly : is_readonly;
1447 }
1448
1449 #define SAMPLE_COUNT    5
1450
1451 static int sdhci_get_ro(struct mmc_host *mmc)
1452 {
1453         struct sdhci_host *host;
1454         int i, ro_count;
1455
1456         host = mmc_priv(mmc);
1457
1458         if (!(host->quirks & SDHCI_QUIRK_UNSTABLE_RO_DETECT))
1459                 return check_ro(host);
1460
1461         ro_count = 0;
1462         for (i = 0; i < SAMPLE_COUNT; i++) {
1463                 if (check_ro(host)) {
1464                         if (++ro_count > SAMPLE_COUNT / 2)
1465                                 return 1;
1466                 }
1467                 msleep(30);
1468         }
1469         return 0;
1470 }
1471
1472 static void sdhci_enable_sdio_irq(struct mmc_host *mmc, int enable)
1473 {
1474         struct sdhci_host *host;
1475         unsigned long flags;
1476
1477         host = mmc_priv(mmc);
1478
1479         spin_lock_irqsave(&host->lock, flags);
1480
1481         if (host->flags & SDHCI_DEVICE_DEAD)
1482                 goto out;
1483
1484         if (enable)
1485                 sdhci_unmask_irqs(host, SDHCI_INT_CARD_INT);
1486         else
1487                 sdhci_mask_irqs(host, SDHCI_INT_CARD_INT);
1488 out:
1489         mmiowb();
1490
1491         spin_unlock_irqrestore(&host->lock, flags);
1492 }
1493
1494 static int sdhci_start_signal_voltage_switch(struct mmc_host *mmc,
1495         struct mmc_ios *ios)
1496 {
1497         struct sdhci_host *host;
1498         u8 pwr;
1499         u16 clk, ctrl;
1500         u32 present_state;
1501
1502         host = mmc_priv(mmc);
1503
1504         /*
1505          * Signal Voltage Switching is only applicable for Host Controllers
1506          * v3.00 and above.
1507          */
1508         if (host->version < SDHCI_SPEC_300)
1509                 return 0;
1510
1511         /*
1512          * We first check whether the request is to set signalling voltage
1513          * to 3.3V. If so, we change the voltage to 3.3V and return quickly.
1514          */
1515         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1516         if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) {
1517                 /* Set 1.8V Signal Enable in the Host Control2 register to 0 */
1518                 ctrl &= ~SDHCI_CTRL_VDD_180;
1519                 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1520
1521                 /* Wait for 5ms */
1522                 usleep_range(5000, 5500);
1523
1524                 /* 3.3V regulator output should be stable within 5 ms */
1525                 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1526                 if (!(ctrl & SDHCI_CTRL_VDD_180))
1527                         return 0;
1528                 else {
1529                         printk(KERN_INFO DRIVER_NAME ": Switching to 3.3V "
1530                                 "signalling voltage failed\n");
1531                         return -EIO;
1532                 }
1533         } else if (!(ctrl & SDHCI_CTRL_VDD_180) &&
1534                   (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_180)) {
1535                 /* Stop SDCLK */
1536                 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1537                 clk &= ~SDHCI_CLOCK_CARD_EN;
1538                 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1539
1540                 /* Check whether DAT[3:0] is 0000 */
1541                 present_state = sdhci_readl(host, SDHCI_PRESENT_STATE);
1542                 if (!((present_state & SDHCI_DATA_LVL_MASK) >>
1543                        SDHCI_DATA_LVL_SHIFT)) {
1544                         /*
1545                          * Enable 1.8V Signal Enable in the Host Control2
1546                          * register
1547                          */
1548                         ctrl |= SDHCI_CTRL_VDD_180;
1549                         sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1550
1551                         /* Wait for 5ms */
1552                         usleep_range(5000, 5500);
1553
1554                         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1555                         if (ctrl & SDHCI_CTRL_VDD_180) {
1556                                 /* Provide SDCLK again and wait for 1ms*/
1557                                 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1558                                 clk |= SDHCI_CLOCK_CARD_EN;
1559                                 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1560                                 usleep_range(1000, 1500);
1561
1562                                 /*
1563                                  * If DAT[3:0] level is 1111b, then the card
1564                                  * was successfully switched to 1.8V signaling.
1565                                  */
1566                                 present_state = sdhci_readl(host,
1567                                                         SDHCI_PRESENT_STATE);
1568                                 if ((present_state & SDHCI_DATA_LVL_MASK) ==
1569                                      SDHCI_DATA_LVL_MASK)
1570                                         return 0;
1571                         }
1572                 }
1573
1574                 /*
1575                  * If we are here, that means the switch to 1.8V signaling
1576                  * failed. We power cycle the card, and retry initialization
1577                  * sequence by setting S18R to 0.
1578                  */
1579                 pwr = sdhci_readb(host, SDHCI_POWER_CONTROL);
1580                 pwr &= ~SDHCI_POWER_ON;
1581                 sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
1582
1583                 /* Wait for 1ms as per the spec */
1584                 usleep_range(1000, 1500);
1585                 pwr |= SDHCI_POWER_ON;
1586                 sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
1587
1588                 printk(KERN_INFO DRIVER_NAME ": Switching to 1.8V signalling "
1589                         "voltage failed, retrying with S18R set to 0\n");
1590                 return -EAGAIN;
1591         } else
1592                 /* No signal voltage switch required */
1593                 return 0;
1594 }
1595
1596 static int sdhci_execute_tuning(struct mmc_host *mmc)
1597 {
1598         struct sdhci_host *host;
1599         u16 ctrl;
1600         u32 ier;
1601         int tuning_loop_counter = MAX_TUNING_LOOP;
1602         unsigned long timeout;
1603         int err = 0;
1604
1605         host = mmc_priv(mmc);
1606
1607         disable_irq(host->irq);
1608         spin_lock(&host->lock);
1609
1610         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1611
1612         /*
1613          * Host Controller needs tuning only in case of SDR104 mode
1614          * and for SDR50 mode when Use Tuning for SDR50 is set in
1615          * Capabilities register.
1616          */
1617         if (((ctrl & SDHCI_CTRL_UHS_MASK) == SDHCI_CTRL_UHS_SDR104) ||
1618             (((ctrl & SDHCI_CTRL_UHS_MASK) == SDHCI_CTRL_UHS_SDR50) &&
1619             (host->flags & SDHCI_SDR50_NEEDS_TUNING)))
1620                 ctrl |= SDHCI_CTRL_EXEC_TUNING;
1621         else {
1622                 spin_unlock(&host->lock);
1623                 enable_irq(host->irq);
1624                 return 0;
1625         }
1626
1627         sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1628
1629         /*
1630          * As per the Host Controller spec v3.00, tuning command
1631          * generates Buffer Read Ready interrupt, so enable that.
1632          *
1633          * Note: The spec clearly says that when tuning sequence
1634          * is being performed, the controller does not generate
1635          * interrupts other than Buffer Read Ready interrupt. But
1636          * to make sure we don't hit a controller bug, we _only_
1637          * enable Buffer Read Ready interrupt here.
1638          */
1639         ier = sdhci_readl(host, SDHCI_INT_ENABLE);
1640         sdhci_clear_set_irqs(host, ier, SDHCI_INT_DATA_AVAIL);
1641
1642         /*
1643          * Issue CMD19 repeatedly till Execute Tuning is set to 0 or the number
1644          * of loops reaches 40 times or a timeout of 150ms occurs.
1645          */
1646         timeout = 150;
1647         do {
1648                 struct mmc_command cmd = {0};
1649                 struct mmc_request mrq = {0};
1650
1651                 if (!tuning_loop_counter && !timeout)
1652                         break;
1653
1654                 cmd.opcode = MMC_SEND_TUNING_BLOCK;
1655                 cmd.arg = 0;
1656                 cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
1657                 cmd.retries = 0;
1658                 cmd.data = NULL;
1659                 cmd.error = 0;
1660
1661                 mrq.cmd = &cmd;
1662                 host->mrq = &mrq;
1663
1664                 /*
1665                  * In response to CMD19, the card sends 64 bytes of tuning
1666                  * block to the Host Controller. So we set the block size
1667                  * to 64 here.
1668                  */
1669                 sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 64), SDHCI_BLOCK_SIZE);
1670
1671                 /*
1672                  * The tuning block is sent by the card to the host controller.
1673                  * So we set the TRNS_READ bit in the Transfer Mode register.
1674                  * This also takes care of setting DMA Enable and Multi Block
1675                  * Select in the same register to 0.
1676                  */
1677                 sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE);
1678
1679                 sdhci_send_command(host, &cmd);
1680
1681                 host->cmd = NULL;
1682                 host->mrq = NULL;
1683
1684                 spin_unlock(&host->lock);
1685                 enable_irq(host->irq);
1686
1687                 /* Wait for Buffer Read Ready interrupt */
1688                 wait_event_interruptible_timeout(host->buf_ready_int,
1689                                         (host->tuning_done == 1),
1690                                         msecs_to_jiffies(50));
1691                 disable_irq(host->irq);
1692                 spin_lock(&host->lock);
1693
1694                 if (!host->tuning_done) {
1695                         printk(KERN_INFO DRIVER_NAME ": Timeout waiting for "
1696                                 "Buffer Read Ready interrupt during tuning "
1697                                 "procedure, falling back to fixed sampling "
1698                                 "clock\n");
1699                         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1700                         ctrl &= ~SDHCI_CTRL_TUNED_CLK;
1701                         ctrl &= ~SDHCI_CTRL_EXEC_TUNING;
1702                         sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1703
1704                         err = -EIO;
1705                         goto out;
1706                 }
1707
1708                 host->tuning_done = 0;
1709
1710                 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1711                 tuning_loop_counter--;
1712                 timeout--;
1713                 mdelay(1);
1714         } while (ctrl & SDHCI_CTRL_EXEC_TUNING);
1715
1716         /*
1717          * The Host Driver has exhausted the maximum number of loops allowed,
1718          * so use fixed sampling frequency.
1719          */
1720         if (!tuning_loop_counter || !timeout) {
1721                 ctrl &= ~SDHCI_CTRL_TUNED_CLK;
1722                 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1723         } else {
1724                 if (!(ctrl & SDHCI_CTRL_TUNED_CLK)) {
1725                         printk(KERN_INFO DRIVER_NAME ": Tuning procedure"
1726                                 " failed, falling back to fixed sampling"
1727                                 " clock\n");
1728                         err = -EIO;
1729                 }
1730         }
1731
1732 out:
1733         /*
1734          * If this is the very first time we are here, we start the retuning
1735          * timer. Since only during the first time, SDHCI_NEEDS_RETUNING
1736          * flag won't be set, we check this condition before actually starting
1737          * the timer.
1738          */
1739         if (!(host->flags & SDHCI_NEEDS_RETUNING) && host->tuning_count &&
1740             (host->tuning_mode == SDHCI_TUNING_MODE_1)) {
1741                 mod_timer(&host->tuning_timer, jiffies +
1742                         host->tuning_count * HZ);
1743                 /* Tuning mode 1 limits the maximum data length to 4MB */
1744                 mmc->max_blk_count = (4 * 1024 * 1024) / mmc->max_blk_size;
1745         } else {
1746                 host->flags &= ~SDHCI_NEEDS_RETUNING;
1747                 /* Reload the new initial value for timer */
1748                 if (host->tuning_mode == SDHCI_TUNING_MODE_1)
1749                         mod_timer(&host->tuning_timer, jiffies +
1750                                 host->tuning_count * HZ);
1751         }
1752
1753         /*
1754          * In case tuning fails, host controllers which support re-tuning can
1755          * try tuning again at a later time, when the re-tuning timer expires.
1756          * So for these controllers, we return 0. Since there might be other
1757          * controllers who do not have this capability, we return error for
1758          * them.
1759          */
1760         if (err && host->tuning_count &&
1761             host->tuning_mode == SDHCI_TUNING_MODE_1)
1762                 err = 0;
1763
1764         sdhci_clear_set_irqs(host, SDHCI_INT_DATA_AVAIL, ier);
1765         spin_unlock(&host->lock);
1766         enable_irq(host->irq);
1767
1768         return err;
1769 }
1770
1771 static void sdhci_enable_preset_value(struct mmc_host *mmc, bool enable)
1772 {
1773         struct sdhci_host *host;
1774         u16 ctrl;
1775         unsigned long flags;
1776
1777         host = mmc_priv(mmc);
1778
1779         /* Host Controller v3.00 defines preset value registers */
1780         if (host->version < SDHCI_SPEC_300)
1781                 return;
1782
1783         spin_lock_irqsave(&host->lock, flags);
1784
1785         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1786
1787         /*
1788          * We only enable or disable Preset Value if they are not already
1789          * enabled or disabled respectively. Otherwise, we bail out.
1790          */
1791         if (enable && !(ctrl & SDHCI_CTRL_PRESET_VAL_ENABLE)) {
1792                 ctrl |= SDHCI_CTRL_PRESET_VAL_ENABLE;
1793                 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1794         } else if (!enable && (ctrl & SDHCI_CTRL_PRESET_VAL_ENABLE)) {
1795                 ctrl &= ~SDHCI_CTRL_PRESET_VAL_ENABLE;
1796                 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1797         }
1798
1799         spin_unlock_irqrestore(&host->lock, flags);
1800 }
1801
1802 static const struct mmc_host_ops sdhci_ops = {
1803         .request        = sdhci_request,
1804         .set_ios        = sdhci_set_ios,
1805         .get_ro         = sdhci_get_ro,
1806         .enable_sdio_irq = sdhci_enable_sdio_irq,
1807         .start_signal_voltage_switch    = sdhci_start_signal_voltage_switch,
1808         .execute_tuning                 = sdhci_execute_tuning,
1809         .enable_preset_value            = sdhci_enable_preset_value,
1810 };
1811
1812 /*****************************************************************************\
1813  *                                                                           *
1814  * Tasklets                                                                  *
1815  *                                                                           *
1816 \*****************************************************************************/
1817
1818 static void sdhci_tasklet_card(unsigned long param)
1819 {
1820         struct sdhci_host *host;
1821         unsigned long flags;
1822
1823         host = (struct sdhci_host*)param;
1824
1825         spin_lock_irqsave(&host->lock, flags);
1826
1827         if (!(sdhci_readl(host, SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT)) {
1828                 if (host->mrq) {
1829                         printk(KERN_ERR "%s: Card removed during transfer!\n",
1830                                 mmc_hostname(host->mmc));
1831                         printk(KERN_ERR "%s: Resetting controller.\n",
1832                                 mmc_hostname(host->mmc));
1833
1834                         sdhci_reset(host, SDHCI_RESET_CMD);
1835                         sdhci_reset(host, SDHCI_RESET_DATA);
1836
1837                         host->mrq->cmd->error = -ENOMEDIUM;
1838                         tasklet_schedule(&host->finish_tasklet);
1839                 }
1840         }
1841
1842         spin_unlock_irqrestore(&host->lock, flags);
1843
1844         mmc_detect_change(host->mmc, msecs_to_jiffies(200));
1845 }
1846
1847 static void sdhci_tasklet_finish(unsigned long param)
1848 {
1849         struct sdhci_host *host;
1850         unsigned long flags;
1851         struct mmc_request *mrq;
1852
1853         host = (struct sdhci_host*)param;
1854
1855         /*
1856          * If this tasklet gets rescheduled while running, it will
1857          * be run again afterwards but without any active request.
1858          */
1859         if (!host->mrq)
1860                 return;
1861
1862         spin_lock_irqsave(&host->lock, flags);
1863
1864         del_timer(&host->timer);
1865
1866         mrq = host->mrq;
1867
1868         /*
1869          * The controller needs a reset of internal state machines
1870          * upon error conditions.
1871          */
1872         if (!(host->flags & SDHCI_DEVICE_DEAD) &&
1873             ((mrq->cmd && mrq->cmd->error) ||
1874                  (mrq->data && (mrq->data->error ||
1875                   (mrq->data->stop && mrq->data->stop->error))) ||
1876                    (host->quirks & SDHCI_QUIRK_RESET_AFTER_REQUEST))) {
1877
1878                 /* Some controllers need this kick or reset won't work here */
1879                 if (host->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET) {
1880                         unsigned int clock;
1881
1882                         /* This is to force an update */
1883                         clock = host->clock;
1884                         host->clock = 0;
1885                         sdhci_set_clock(host, clock);
1886                 }
1887
1888                 /* Spec says we should do both at the same time, but Ricoh
1889                    controllers do not like that. */
1890                 sdhci_reset(host, SDHCI_RESET_CMD);
1891                 sdhci_reset(host, SDHCI_RESET_DATA);
1892         }
1893
1894         host->mrq = NULL;
1895         host->cmd = NULL;
1896         host->data = NULL;
1897
1898 #ifndef SDHCI_USE_LEDS_CLASS
1899         sdhci_deactivate_led(host);
1900 #endif
1901
1902         mmiowb();
1903         spin_unlock_irqrestore(&host->lock, flags);
1904
1905         mmc_request_done(host->mmc, mrq);
1906 }
1907
1908 static void sdhci_timeout_timer(unsigned long data)
1909 {
1910         struct sdhci_host *host;
1911         unsigned long flags;
1912
1913         host = (struct sdhci_host*)data;
1914
1915         spin_lock_irqsave(&host->lock, flags);
1916
1917         if (host->mrq) {
1918                 printk(KERN_ERR "%s: Timeout waiting for hardware "
1919                         "interrupt.\n", mmc_hostname(host->mmc));
1920                 sdhci_dumpregs(host);
1921
1922                 if (host->data) {
1923                         host->data->error = -ETIMEDOUT;
1924                         sdhci_finish_data(host);
1925                 } else {
1926                         if (host->cmd)
1927                                 host->cmd->error = -ETIMEDOUT;
1928                         else
1929                                 host->mrq->cmd->error = -ETIMEDOUT;
1930
1931                         tasklet_schedule(&host->finish_tasklet);
1932                 }
1933         }
1934
1935         mmiowb();
1936         spin_unlock_irqrestore(&host->lock, flags);
1937 }
1938
1939 static void sdhci_tuning_timer(unsigned long data)
1940 {
1941         struct sdhci_host *host;
1942         unsigned long flags;
1943
1944         host = (struct sdhci_host *)data;
1945
1946         spin_lock_irqsave(&host->lock, flags);
1947
1948         host->flags |= SDHCI_NEEDS_RETUNING;
1949
1950         spin_unlock_irqrestore(&host->lock, flags);
1951 }
1952
1953 /*****************************************************************************\
1954  *                                                                           *
1955  * Interrupt handling                                                        *
1956  *                                                                           *
1957 \*****************************************************************************/
1958
1959 static void sdhci_cmd_irq(struct sdhci_host *host, u32 intmask)
1960 {
1961         BUG_ON(intmask == 0);
1962
1963         if (!host->cmd) {
1964                 printk(KERN_ERR "%s: Got command interrupt 0x%08x even "
1965                         "though no command operation was in progress.\n",
1966                         mmc_hostname(host->mmc), (unsigned)intmask);
1967                 sdhci_dumpregs(host);
1968                 return;
1969         }
1970
1971         if (intmask & SDHCI_INT_TIMEOUT)
1972                 host->cmd->error = -ETIMEDOUT;
1973         else if (intmask & (SDHCI_INT_CRC | SDHCI_INT_END_BIT |
1974                         SDHCI_INT_INDEX))
1975                 host->cmd->error = -EILSEQ;
1976
1977         if (host->cmd->error) {
1978                 tasklet_schedule(&host->finish_tasklet);
1979                 return;
1980         }
1981
1982         /*
1983          * The host can send and interrupt when the busy state has
1984          * ended, allowing us to wait without wasting CPU cycles.
1985          * Unfortunately this is overloaded on the "data complete"
1986          * interrupt, so we need to take some care when handling
1987          * it.
1988          *
1989          * Note: The 1.0 specification is a bit ambiguous about this
1990          *       feature so there might be some problems with older
1991          *       controllers.
1992          */
1993         if (host->cmd->flags & MMC_RSP_BUSY) {
1994                 if (host->cmd->data)
1995                         DBG("Cannot wait for busy signal when also "
1996                                 "doing a data transfer");
1997                 else if (!(host->quirks & SDHCI_QUIRK_NO_BUSY_IRQ))
1998                         return;
1999
2000                 /* The controller does not support the end-of-busy IRQ,
2001                  * fall through and take the SDHCI_INT_RESPONSE */
2002         }
2003
2004         if (intmask & SDHCI_INT_RESPONSE)
2005                 sdhci_finish_command(host);
2006 }
2007
2008 #ifdef CONFIG_MMC_DEBUG
2009 static void sdhci_show_adma_error(struct sdhci_host *host)
2010 {
2011         const char *name = mmc_hostname(host->mmc);
2012         u8 *desc = host->adma_desc;
2013         __le32 *dma;
2014         __le16 *len;
2015         u8 attr;
2016
2017         sdhci_dumpregs(host);
2018
2019         while (true) {
2020                 dma = (__le32 *)(desc + 4);
2021                 len = (__le16 *)(desc + 2);
2022                 attr = *desc;
2023
2024                 DBG("%s: %p: DMA 0x%08x, LEN 0x%04x, Attr=0x%02x\n",
2025                     name, desc, le32_to_cpu(*dma), le16_to_cpu(*len), attr);
2026
2027                 desc += 8;
2028
2029                 if (attr & 2)
2030                         break;
2031         }
2032 }
2033 #else
2034 static void sdhci_show_adma_error(struct sdhci_host *host) { }
2035 #endif
2036
2037 static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
2038 {
2039         BUG_ON(intmask == 0);
2040
2041         /* CMD19 generates _only_ Buffer Read Ready interrupt */
2042         if (intmask & SDHCI_INT_DATA_AVAIL) {
2043                 if (SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND)) ==
2044                     MMC_SEND_TUNING_BLOCK) {
2045                         host->tuning_done = 1;
2046                         wake_up(&host->buf_ready_int);
2047                         return;
2048                 }
2049         }
2050
2051         if (!host->data) {
2052                 /*
2053                  * The "data complete" interrupt is also used to
2054                  * indicate that a busy state has ended. See comment
2055                  * above in sdhci_cmd_irq().
2056                  */
2057                 if (host->cmd && (host->cmd->flags & MMC_RSP_BUSY)) {
2058                         if (intmask & SDHCI_INT_DATA_END) {
2059                                 sdhci_finish_command(host);
2060                                 return;
2061                         }
2062                 }
2063
2064                 printk(KERN_ERR "%s: Got data interrupt 0x%08x even "
2065                         "though no data operation was in progress.\n",
2066                         mmc_hostname(host->mmc), (unsigned)intmask);
2067                 sdhci_dumpregs(host);
2068
2069                 return;
2070         }
2071
2072         if (intmask & SDHCI_INT_DATA_TIMEOUT)
2073                 host->data->error = -ETIMEDOUT;
2074         else if (intmask & SDHCI_INT_DATA_END_BIT)
2075                 host->data->error = -EILSEQ;
2076         else if ((intmask & SDHCI_INT_DATA_CRC) &&
2077                 SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND))
2078                         != MMC_BUS_TEST_R)
2079                 host->data->error = -EILSEQ;
2080         else if (intmask & SDHCI_INT_ADMA_ERROR) {
2081                 printk(KERN_ERR "%s: ADMA error\n", mmc_hostname(host->mmc));
2082                 sdhci_show_adma_error(host);
2083                 host->data->error = -EIO;
2084         }
2085
2086         if (host->data->error)
2087                 sdhci_finish_data(host);
2088         else {
2089                 if (intmask & (SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL))
2090                         sdhci_transfer_pio(host);
2091
2092                 /*
2093                  * We currently don't do anything fancy with DMA
2094                  * boundaries, but as we can't disable the feature
2095                  * we need to at least restart the transfer.
2096                  *
2097                  * According to the spec sdhci_readl(host, SDHCI_DMA_ADDRESS)
2098                  * should return a valid address to continue from, but as
2099                  * some controllers are faulty, don't trust them.
2100                  */
2101                 if (intmask & SDHCI_INT_DMA_END) {
2102                         u32 dmastart, dmanow;
2103                         dmastart = sg_dma_address(host->data->sg);
2104                         dmanow = dmastart + host->data->bytes_xfered;
2105                         /*
2106                          * Force update to the next DMA block boundary.
2107                          */
2108                         dmanow = (dmanow &
2109                                 ~(SDHCI_DEFAULT_BOUNDARY_SIZE - 1)) +
2110                                 SDHCI_DEFAULT_BOUNDARY_SIZE;
2111                         host->data->bytes_xfered = dmanow - dmastart;
2112                         DBG("%s: DMA base 0x%08x, transferred 0x%06x bytes,"
2113                                 " next 0x%08x\n",
2114                                 mmc_hostname(host->mmc), dmastart,
2115                                 host->data->bytes_xfered, dmanow);
2116                         sdhci_writel(host, dmanow, SDHCI_DMA_ADDRESS);
2117                 }
2118
2119                 if (intmask & SDHCI_INT_DATA_END) {
2120                         if (host->cmd) {
2121                                 /*
2122                                  * Data managed to finish before the
2123                                  * command completed. Make sure we do
2124                                  * things in the proper order.
2125                                  */
2126                                 host->data_early = 1;
2127                         } else {
2128                                 sdhci_finish_data(host);
2129                         }
2130                 }
2131         }
2132 }
2133
2134 static irqreturn_t sdhci_irq(int irq, void *dev_id)
2135 {
2136         irqreturn_t result;
2137         struct sdhci_host* host = dev_id;
2138         u32 intmask;
2139         int cardint = 0;
2140
2141         spin_lock(&host->lock);
2142
2143         intmask = sdhci_readl(host, SDHCI_INT_STATUS);
2144
2145         if (!intmask || intmask == 0xffffffff) {
2146                 result = IRQ_NONE;
2147                 goto out;
2148         }
2149
2150         DBG("*** %s got interrupt: 0x%08x\n",
2151                 mmc_hostname(host->mmc), intmask);
2152
2153         if (intmask & (SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE)) {
2154                 u32 present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
2155                               SDHCI_CARD_PRESENT;
2156
2157                 /*
2158                  * There is a observation on i.mx esdhc.  INSERT bit will be
2159                  * immediately set again when it gets cleared, if a card is
2160                  * inserted.  We have to mask the irq to prevent interrupt
2161                  * storm which will freeze the system.  And the REMOVE gets
2162                  * the same situation.
2163                  *
2164                  * More testing are needed here to ensure it works for other
2165                  * platforms though.
2166                  */
2167                 sdhci_mask_irqs(host, present ? SDHCI_INT_CARD_INSERT :
2168                                                 SDHCI_INT_CARD_REMOVE);
2169                 sdhci_unmask_irqs(host, present ? SDHCI_INT_CARD_REMOVE :
2170                                                   SDHCI_INT_CARD_INSERT);
2171
2172                 sdhci_writel(host, intmask & (SDHCI_INT_CARD_INSERT |
2173                              SDHCI_INT_CARD_REMOVE), SDHCI_INT_STATUS);
2174                 intmask &= ~(SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE);
2175                 tasklet_schedule(&host->card_tasklet);
2176         }
2177
2178         if (intmask & SDHCI_INT_CMD_MASK) {
2179                 sdhci_writel(host, intmask & SDHCI_INT_CMD_MASK,
2180                         SDHCI_INT_STATUS);
2181                 sdhci_cmd_irq(host, intmask & SDHCI_INT_CMD_MASK);
2182         }
2183
2184         if (intmask & SDHCI_INT_DATA_MASK) {
2185                 sdhci_writel(host, intmask & SDHCI_INT_DATA_MASK,
2186                         SDHCI_INT_STATUS);
2187                 sdhci_data_irq(host, intmask & SDHCI_INT_DATA_MASK);
2188         }
2189
2190         intmask &= ~(SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK);
2191
2192         intmask &= ~SDHCI_INT_ERROR;
2193
2194         if (intmask & SDHCI_INT_BUS_POWER) {
2195                 printk(KERN_ERR "%s: Card is consuming too much power!\n",
2196                         mmc_hostname(host->mmc));
2197                 sdhci_writel(host, SDHCI_INT_BUS_POWER, SDHCI_INT_STATUS);
2198         }
2199
2200         intmask &= ~SDHCI_INT_BUS_POWER;
2201
2202         if (intmask & SDHCI_INT_CARD_INT)
2203                 cardint = 1;
2204
2205         intmask &= ~SDHCI_INT_CARD_INT;
2206
2207         if (intmask) {
2208                 printk(KERN_ERR "%s: Unexpected interrupt 0x%08x.\n",
2209                         mmc_hostname(host->mmc), intmask);
2210                 sdhci_dumpregs(host);
2211
2212                 sdhci_writel(host, intmask, SDHCI_INT_STATUS);
2213         }
2214
2215         result = IRQ_HANDLED;
2216
2217         mmiowb();
2218 out:
2219         spin_unlock(&host->lock);
2220
2221         /*
2222          * We have to delay this as it calls back into the driver.
2223          */
2224         if (cardint)
2225                 mmc_signal_sdio_irq(host->mmc);
2226
2227         return result;
2228 }
2229
2230 /*****************************************************************************\
2231  *                                                                           *
2232  * Suspend/resume                                                            *
2233  *                                                                           *
2234 \*****************************************************************************/
2235
2236 #ifdef CONFIG_PM
2237
2238 int sdhci_suspend_host(struct sdhci_host *host, pm_message_t state)
2239 {
2240         int ret;
2241
2242         sdhci_disable_card_detection(host);
2243
2244         /* Disable tuning since we are suspending */
2245         if (host->version >= SDHCI_SPEC_300 && host->tuning_count &&
2246             host->tuning_mode == SDHCI_TUNING_MODE_1) {
2247                 host->flags &= ~SDHCI_NEEDS_RETUNING;
2248                 mod_timer(&host->tuning_timer, jiffies +
2249                         host->tuning_count * HZ);
2250         }
2251
2252         ret = mmc_suspend_host(host->mmc);
2253         if (ret)
2254                 return ret;
2255
2256         free_irq(host->irq, host);
2257
2258         if (host->vmmc)
2259                 ret = regulator_disable(host->vmmc);
2260
2261         return ret;
2262 }
2263
2264 EXPORT_SYMBOL_GPL(sdhci_suspend_host);
2265
2266 int sdhci_resume_host(struct sdhci_host *host)
2267 {
2268         int ret;
2269
2270         if (host->vmmc) {
2271                 int ret = regulator_enable(host->vmmc);
2272                 if (ret)
2273                         return ret;
2274         }
2275
2276
2277         if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
2278                 if (host->ops->enable_dma)
2279                         host->ops->enable_dma(host);
2280         }
2281
2282         ret = request_irq(host->irq, sdhci_irq, IRQF_SHARED,
2283                           mmc_hostname(host->mmc), host);
2284         if (ret)
2285                 return ret;
2286
2287         sdhci_init(host, (host->mmc->pm_flags & MMC_PM_KEEP_POWER));
2288         mmiowb();
2289
2290         ret = mmc_resume_host(host->mmc);
2291         sdhci_enable_card_detection(host);
2292
2293         /* Set the re-tuning expiration flag */
2294         if ((host->version >= SDHCI_SPEC_300) && host->tuning_count &&
2295             (host->tuning_mode == SDHCI_TUNING_MODE_1))
2296                 host->flags |= SDHCI_NEEDS_RETUNING;
2297
2298         return ret;
2299 }
2300
2301 EXPORT_SYMBOL_GPL(sdhci_resume_host);
2302
2303 void sdhci_enable_irq_wakeups(struct sdhci_host *host)
2304 {
2305         u8 val;
2306         val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
2307         val |= SDHCI_WAKE_ON_INT;
2308         sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
2309 }
2310
2311 EXPORT_SYMBOL_GPL(sdhci_enable_irq_wakeups);
2312
2313 #endif /* CONFIG_PM */
2314
2315 /*****************************************************************************\
2316  *                                                                           *
2317  * Device allocation/registration                                            *
2318  *                                                                           *
2319 \*****************************************************************************/
2320
2321 struct sdhci_host *sdhci_alloc_host(struct device *dev,
2322         size_t priv_size)
2323 {
2324         struct mmc_host *mmc;
2325         struct sdhci_host *host;
2326
2327         WARN_ON(dev == NULL);
2328
2329         mmc = mmc_alloc_host(sizeof(struct sdhci_host) + priv_size, dev);
2330         if (!mmc)
2331                 return ERR_PTR(-ENOMEM);
2332
2333         host = mmc_priv(mmc);
2334         host->mmc = mmc;
2335
2336         return host;
2337 }
2338
2339 EXPORT_SYMBOL_GPL(sdhci_alloc_host);
2340
2341 int sdhci_add_host(struct sdhci_host *host)
2342 {
2343         struct mmc_host *mmc;
2344         u32 caps[2];
2345         u32 max_current_caps;
2346         unsigned int ocr_avail;
2347         int ret;
2348
2349         WARN_ON(host == NULL);
2350         if (host == NULL)
2351                 return -EINVAL;
2352
2353         mmc = host->mmc;
2354
2355         if (debug_quirks)
2356                 host->quirks = debug_quirks;
2357
2358         sdhci_reset(host, SDHCI_RESET_ALL);
2359
2360         host->version = sdhci_readw(host, SDHCI_HOST_VERSION);
2361         host->version = (host->version & SDHCI_SPEC_VER_MASK)
2362                                 >> SDHCI_SPEC_VER_SHIFT;
2363         if (host->version > SDHCI_SPEC_300) {
2364                 printk(KERN_ERR "%s: Unknown controller version (%d). "
2365                         "You may experience problems.\n", mmc_hostname(mmc),
2366                         host->version);
2367         }
2368
2369         caps[0] = (host->quirks & SDHCI_QUIRK_MISSING_CAPS) ? host->caps :
2370                 sdhci_readl(host, SDHCI_CAPABILITIES);
2371
2372         caps[1] = (host->version >= SDHCI_SPEC_300) ?
2373                 sdhci_readl(host, SDHCI_CAPABILITIES_1) : 0;
2374
2375         if (host->quirks & SDHCI_QUIRK_FORCE_DMA)
2376                 host->flags |= SDHCI_USE_SDMA;
2377         else if (!(caps[0] & SDHCI_CAN_DO_SDMA))
2378                 DBG("Controller doesn't have SDMA capability\n");
2379         else
2380                 host->flags |= SDHCI_USE_SDMA;
2381
2382         if ((host->quirks & SDHCI_QUIRK_BROKEN_DMA) &&
2383                 (host->flags & SDHCI_USE_SDMA)) {
2384                 DBG("Disabling DMA as it is marked broken\n");
2385                 host->flags &= ~SDHCI_USE_SDMA;
2386         }
2387
2388         if ((host->version >= SDHCI_SPEC_200) &&
2389                 (caps[0] & SDHCI_CAN_DO_ADMA2))
2390                 host->flags |= SDHCI_USE_ADMA;
2391
2392         if ((host->quirks & SDHCI_QUIRK_BROKEN_ADMA) &&
2393                 (host->flags & SDHCI_USE_ADMA)) {
2394                 DBG("Disabling ADMA as it is marked broken\n");
2395                 host->flags &= ~SDHCI_USE_ADMA;
2396         }
2397
2398         if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
2399                 if (host->ops->enable_dma) {
2400                         if (host->ops->enable_dma(host)) {
2401                                 printk(KERN_WARNING "%s: No suitable DMA "
2402                                         "available. Falling back to PIO.\n",
2403                                         mmc_hostname(mmc));
2404                                 host->flags &=
2405                                         ~(SDHCI_USE_SDMA | SDHCI_USE_ADMA);
2406                         }
2407                 }
2408         }
2409
2410         if (host->flags & SDHCI_USE_ADMA) {
2411                 /*
2412                  * We need to allocate descriptors for all sg entries
2413                  * (128) and potentially one alignment transfer for
2414                  * each of those entries.
2415                  */
2416                 host->adma_desc = kmalloc((128 * 2 + 1) * 4, GFP_KERNEL);
2417                 host->align_buffer = kmalloc(128 * 4, GFP_KERNEL);
2418                 if (!host->adma_desc || !host->align_buffer) {
2419                         kfree(host->adma_desc);
2420                         kfree(host->align_buffer);
2421                         printk(KERN_WARNING "%s: Unable to allocate ADMA "
2422                                 "buffers. Falling back to standard DMA.\n",
2423                                 mmc_hostname(mmc));
2424                         host->flags &= ~SDHCI_USE_ADMA;
2425                 }
2426         }
2427
2428         /*
2429          * If we use DMA, then it's up to the caller to set the DMA
2430          * mask, but PIO does not need the hw shim so we set a new
2431          * mask here in that case.
2432          */
2433         if (!(host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA))) {
2434                 host->dma_mask = DMA_BIT_MASK(64);
2435                 mmc_dev(host->mmc)->dma_mask = &host->dma_mask;
2436         }
2437
2438         if (host->version >= SDHCI_SPEC_300)
2439                 host->max_clk = (caps[0] & SDHCI_CLOCK_V3_BASE_MASK)
2440                         >> SDHCI_CLOCK_BASE_SHIFT;
2441         else
2442                 host->max_clk = (caps[0] & SDHCI_CLOCK_BASE_MASK)
2443                         >> SDHCI_CLOCK_BASE_SHIFT;
2444
2445         host->max_clk *= 1000000;
2446         if (host->max_clk == 0 || host->quirks &
2447                         SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN) {
2448                 if (!host->ops->get_max_clock) {
2449                         printk(KERN_ERR
2450                                "%s: Hardware doesn't specify base clock "
2451                                "frequency.\n", mmc_hostname(mmc));
2452                         return -ENODEV;
2453                 }
2454                 host->max_clk = host->ops->get_max_clock(host);
2455         }
2456
2457         host->timeout_clk =
2458                 (caps[0] & SDHCI_TIMEOUT_CLK_MASK) >> SDHCI_TIMEOUT_CLK_SHIFT;
2459         if (host->timeout_clk == 0) {
2460                 if (host->ops->get_timeout_clock) {
2461                         host->timeout_clk = host->ops->get_timeout_clock(host);
2462                 } else if (!(host->quirks &
2463                                 SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)) {
2464                         printk(KERN_ERR
2465                                "%s: Hardware doesn't specify timeout clock "
2466                                "frequency.\n", mmc_hostname(mmc));
2467                         return -ENODEV;
2468                 }
2469         }
2470         if (caps[0] & SDHCI_TIMEOUT_CLK_UNIT)
2471                 host->timeout_clk *= 1000;
2472
2473         if (host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)
2474                 host->timeout_clk = host->clock / 1000;
2475
2476         /*
2477          * In case of Host Controller v3.00, find out whether clock
2478          * multiplier is supported.
2479          */
2480         host->clk_mul = (caps[1] & SDHCI_CLOCK_MUL_MASK) >>
2481                         SDHCI_CLOCK_MUL_SHIFT;
2482
2483         /*
2484          * In case the value in Clock Multiplier is 0, then programmable
2485          * clock mode is not supported, otherwise the actual clock
2486          * multiplier is one more than the value of Clock Multiplier
2487          * in the Capabilities Register.
2488          */
2489         if (host->clk_mul)
2490                 host->clk_mul += 1;
2491
2492         /*
2493          * Set host parameters.
2494          */
2495         mmc->ops = &sdhci_ops;
2496         mmc->f_max = host->max_clk;
2497         if (host->ops->get_min_clock)
2498                 mmc->f_min = host->ops->get_min_clock(host);
2499         else if (host->version >= SDHCI_SPEC_300) {
2500                 if (host->clk_mul) {
2501                         mmc->f_min = (host->max_clk * host->clk_mul) / 1024;
2502                         mmc->f_max = host->max_clk * host->clk_mul;
2503                 } else
2504                         mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_300;
2505         } else
2506                 mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_200;
2507
2508         if (host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)
2509                 mmc->max_discard_to = (1 << 27) / (mmc->f_max / 1000);
2510         else
2511                 mmc->max_discard_to = (1 << 27) / host->timeout_clk;
2512
2513         mmc->caps |= MMC_CAP_SDIO_IRQ | MMC_CAP_ERASE | MMC_CAP_CMD23;
2514
2515         if (host->quirks & SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12)
2516                 host->flags |= SDHCI_AUTO_CMD12;
2517
2518         /* Auto-CMD23 stuff only works in ADMA or PIO. */
2519         if ((host->version >= SDHCI_SPEC_300) &&
2520             ((host->flags & SDHCI_USE_ADMA) ||
2521              !(host->flags & SDHCI_USE_SDMA))) {
2522                 host->flags |= SDHCI_AUTO_CMD23;
2523                 DBG("%s: Auto-CMD23 available\n", mmc_hostname(mmc));
2524         } else {
2525                 DBG("%s: Auto-CMD23 unavailable\n", mmc_hostname(mmc));
2526         }
2527
2528         /*
2529          * A controller may support 8-bit width, but the board itself
2530          * might not have the pins brought out.  Boards that support
2531          * 8-bit width must set "mmc->caps |= MMC_CAP_8_BIT_DATA;" in
2532          * their platform code before calling sdhci_add_host(), and we
2533          * won't assume 8-bit width for hosts without that CAP.
2534          */
2535         if (!(host->quirks & SDHCI_QUIRK_FORCE_1_BIT_DATA))
2536                 mmc->caps |= MMC_CAP_4_BIT_DATA;
2537
2538         if (caps[0] & SDHCI_CAN_DO_HISPD)
2539                 mmc->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED;
2540
2541         if ((host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) &&
2542             mmc_card_is_removable(mmc))
2543                 mmc->caps |= MMC_CAP_NEEDS_POLL;
2544
2545         /* UHS-I mode(s) supported by the host controller. */
2546         if (host->version >= SDHCI_SPEC_300)
2547                 mmc->caps |= MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25;
2548
2549         /* SDR104 supports also implies SDR50 support */
2550         if (caps[1] & SDHCI_SUPPORT_SDR104)
2551                 mmc->caps |= MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_SDR50;
2552         else if (caps[1] & SDHCI_SUPPORT_SDR50)
2553                 mmc->caps |= MMC_CAP_UHS_SDR50;
2554
2555         if (caps[1] & SDHCI_SUPPORT_DDR50)
2556                 mmc->caps |= MMC_CAP_UHS_DDR50;
2557
2558         /* Does the host needs tuning for SDR50? */
2559         if (caps[1] & SDHCI_USE_SDR50_TUNING)
2560                 host->flags |= SDHCI_SDR50_NEEDS_TUNING;
2561
2562         /* Driver Type(s) (A, C, D) supported by the host */
2563         if (caps[1] & SDHCI_DRIVER_TYPE_A)
2564                 mmc->caps |= MMC_CAP_DRIVER_TYPE_A;
2565         if (caps[1] & SDHCI_DRIVER_TYPE_C)
2566                 mmc->caps |= MMC_CAP_DRIVER_TYPE_C;
2567         if (caps[1] & SDHCI_DRIVER_TYPE_D)
2568                 mmc->caps |= MMC_CAP_DRIVER_TYPE_D;
2569
2570         /* Initial value for re-tuning timer count */
2571         host->tuning_count = (caps[1] & SDHCI_RETUNING_TIMER_COUNT_MASK) >>
2572                               SDHCI_RETUNING_TIMER_COUNT_SHIFT;
2573
2574         /*
2575          * In case Re-tuning Timer is not disabled, the actual value of
2576          * re-tuning timer will be 2 ^ (n - 1).
2577          */
2578         if (host->tuning_count)
2579                 host->tuning_count = 1 << (host->tuning_count - 1);
2580
2581         /* Re-tuning mode supported by the Host Controller */
2582         host->tuning_mode = (caps[1] & SDHCI_RETUNING_MODE_MASK) >>
2583                              SDHCI_RETUNING_MODE_SHIFT;
2584
2585         ocr_avail = 0;
2586         /*
2587          * According to SD Host Controller spec v3.00, if the Host System
2588          * can afford more than 150mA, Host Driver should set XPC to 1. Also
2589          * the value is meaningful only if Voltage Support in the Capabilities
2590          * register is set. The actual current value is 4 times the register
2591          * value.
2592          */
2593         max_current_caps = sdhci_readl(host, SDHCI_MAX_CURRENT);
2594
2595         if (caps[0] & SDHCI_CAN_VDD_330) {
2596                 int max_current_330;
2597
2598                 ocr_avail |= MMC_VDD_32_33 | MMC_VDD_33_34;
2599
2600                 max_current_330 = ((max_current_caps &
2601                                    SDHCI_MAX_CURRENT_330_MASK) >>
2602                                    SDHCI_MAX_CURRENT_330_SHIFT) *
2603                                    SDHCI_MAX_CURRENT_MULTIPLIER;
2604
2605                 if (max_current_330 > 150)
2606                         mmc->caps |= MMC_CAP_SET_XPC_330;
2607         }
2608         if (caps[0] & SDHCI_CAN_VDD_300) {
2609                 int max_current_300;
2610
2611                 ocr_avail |= MMC_VDD_29_30 | MMC_VDD_30_31;
2612
2613                 max_current_300 = ((max_current_caps &
2614                                    SDHCI_MAX_CURRENT_300_MASK) >>
2615                                    SDHCI_MAX_CURRENT_300_SHIFT) *
2616                                    SDHCI_MAX_CURRENT_MULTIPLIER;
2617
2618                 if (max_current_300 > 150)
2619                         mmc->caps |= MMC_CAP_SET_XPC_300;
2620         }
2621         if (caps[0] & SDHCI_CAN_VDD_180) {
2622                 int max_current_180;
2623
2624                 ocr_avail |= MMC_VDD_165_195;
2625
2626                 max_current_180 = ((max_current_caps &
2627                                    SDHCI_MAX_CURRENT_180_MASK) >>
2628                                    SDHCI_MAX_CURRENT_180_SHIFT) *
2629                                    SDHCI_MAX_CURRENT_MULTIPLIER;
2630
2631                 if (max_current_180 > 150)
2632                         mmc->caps |= MMC_CAP_SET_XPC_180;
2633
2634                 /* Maximum current capabilities of the host at 1.8V */
2635                 if (max_current_180 >= 800)
2636                         mmc->caps |= MMC_CAP_MAX_CURRENT_800;
2637                 else if (max_current_180 >= 600)
2638                         mmc->caps |= MMC_CAP_MAX_CURRENT_600;
2639                 else if (max_current_180 >= 400)
2640                         mmc->caps |= MMC_CAP_MAX_CURRENT_400;
2641                 else
2642                         mmc->caps |= MMC_CAP_MAX_CURRENT_200;
2643         }
2644
2645         mmc->ocr_avail = ocr_avail;
2646         mmc->ocr_avail_sdio = ocr_avail;
2647         if (host->ocr_avail_sdio)
2648                 mmc->ocr_avail_sdio &= host->ocr_avail_sdio;
2649         mmc->ocr_avail_sd = ocr_avail;
2650         if (host->ocr_avail_sd)
2651                 mmc->ocr_avail_sd &= host->ocr_avail_sd;
2652         else /* normal SD controllers don't support 1.8V */
2653                 mmc->ocr_avail_sd &= ~MMC_VDD_165_195;
2654         mmc->ocr_avail_mmc = ocr_avail;
2655         if (host->ocr_avail_mmc)
2656                 mmc->ocr_avail_mmc &= host->ocr_avail_mmc;
2657
2658         if (mmc->ocr_avail == 0) {
2659                 printk(KERN_ERR "%s: Hardware doesn't report any "
2660                         "support voltages.\n", mmc_hostname(mmc));
2661                 return -ENODEV;
2662         }
2663
2664         spin_lock_init(&host->lock);
2665
2666         /*
2667          * Maximum number of segments. Depends on if the hardware
2668          * can do scatter/gather or not.
2669          */
2670         if (host->flags & SDHCI_USE_ADMA)
2671                 mmc->max_segs = 128;
2672         else if (host->flags & SDHCI_USE_SDMA)
2673                 mmc->max_segs = 1;
2674         else /* PIO */
2675                 mmc->max_segs = 128;
2676
2677         /*
2678          * Maximum number of sectors in one transfer. Limited by DMA boundary
2679          * size (512KiB).
2680          */
2681         mmc->max_req_size = 524288;
2682
2683         /*
2684          * Maximum segment size. Could be one segment with the maximum number
2685          * of bytes. When doing hardware scatter/gather, each entry cannot
2686          * be larger than 64 KiB though.
2687          */
2688         if (host->flags & SDHCI_USE_ADMA) {
2689                 if (host->quirks & SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC)
2690                         mmc->max_seg_size = 65535;
2691                 else
2692                         mmc->max_seg_size = 65536;
2693         } else {
2694                 mmc->max_seg_size = mmc->max_req_size;
2695         }
2696
2697         /*
2698          * Maximum block size. This varies from controller to controller and
2699          * is specified in the capabilities register.
2700          */
2701         if (host->quirks & SDHCI_QUIRK_FORCE_BLK_SZ_2048) {
2702                 mmc->max_blk_size = 2;
2703         } else {
2704                 mmc->max_blk_size = (caps[0] & SDHCI_MAX_BLOCK_MASK) >>
2705                                 SDHCI_MAX_BLOCK_SHIFT;
2706                 if (mmc->max_blk_size >= 3) {
2707                         printk(KERN_WARNING "%s: Invalid maximum block size, "
2708                                 "assuming 512 bytes\n", mmc_hostname(mmc));
2709                         mmc->max_blk_size = 0;
2710                 }
2711         }
2712
2713         mmc->max_blk_size = 512 << mmc->max_blk_size;
2714
2715         /*
2716          * Maximum block count.
2717          */
2718         mmc->max_blk_count = (host->quirks & SDHCI_QUIRK_NO_MULTIBLOCK) ? 1 : 65535;
2719
2720         /*
2721          * Init tasklets.
2722          */
2723         tasklet_init(&host->card_tasklet,
2724                 sdhci_tasklet_card, (unsigned long)host);
2725         tasklet_init(&host->finish_tasklet,
2726                 sdhci_tasklet_finish, (unsigned long)host);
2727
2728         setup_timer(&host->timer, sdhci_timeout_timer, (unsigned long)host);
2729
2730         if (host->version >= SDHCI_SPEC_300) {
2731                 init_waitqueue_head(&host->buf_ready_int);
2732
2733                 /* Initialize re-tuning timer */
2734                 init_timer(&host->tuning_timer);
2735                 host->tuning_timer.data = (unsigned long)host;
2736                 host->tuning_timer.function = sdhci_tuning_timer;
2737         }
2738
2739         ret = request_irq(host->irq, sdhci_irq, IRQF_SHARED,
2740                 mmc_hostname(mmc), host);
2741         if (ret)
2742                 goto untasklet;
2743
2744         host->vmmc = regulator_get(mmc_dev(mmc), "vmmc");
2745         if (IS_ERR(host->vmmc)) {
2746                 printk(KERN_INFO "%s: no vmmc regulator found\n", mmc_hostname(mmc));
2747                 host->vmmc = NULL;
2748         } else {
2749                 regulator_enable(host->vmmc);
2750         }
2751
2752         sdhci_init(host, 0);
2753
2754 #ifdef CONFIG_MMC_DEBUG
2755         sdhci_dumpregs(host);
2756 #endif
2757
2758 #ifdef SDHCI_USE_LEDS_CLASS
2759         snprintf(host->led_name, sizeof(host->led_name),
2760                 "%s::", mmc_hostname(mmc));
2761         host->led.name = host->led_name;
2762         host->led.brightness = LED_OFF;
2763         host->led.default_trigger = mmc_hostname(mmc);
2764         host->led.brightness_set = sdhci_led_control;
2765
2766         ret = led_classdev_register(mmc_dev(mmc), &host->led);
2767         if (ret)
2768                 goto reset;
2769 #endif
2770
2771         mmiowb();
2772
2773         mmc_add_host(mmc);
2774
2775         printk(KERN_INFO "%s: SDHCI controller on %s [%s] using %s\n",
2776                 mmc_hostname(mmc), host->hw_name, dev_name(mmc_dev(mmc)),
2777                 (host->flags & SDHCI_USE_ADMA) ? "ADMA" :
2778                 (host->flags & SDHCI_USE_SDMA) ? "DMA" : "PIO");
2779
2780         sdhci_enable_card_detection(host);
2781
2782         return 0;
2783
2784 #ifdef SDHCI_USE_LEDS_CLASS
2785 reset:
2786         sdhci_reset(host, SDHCI_RESET_ALL);
2787         free_irq(host->irq, host);
2788 #endif
2789 untasklet:
2790         tasklet_kill(&host->card_tasklet);
2791         tasklet_kill(&host->finish_tasklet);
2792
2793         return ret;
2794 }
2795
2796 EXPORT_SYMBOL_GPL(sdhci_add_host);
2797
2798 void sdhci_remove_host(struct sdhci_host *host, int dead)
2799 {
2800         unsigned long flags;
2801
2802         if (dead) {
2803                 spin_lock_irqsave(&host->lock, flags);
2804
2805                 host->flags |= SDHCI_DEVICE_DEAD;
2806
2807                 if (host->mrq) {
2808                         printk(KERN_ERR "%s: Controller removed during "
2809                                 " transfer!\n", mmc_hostname(host->mmc));
2810
2811                         host->mrq->cmd->error = -ENOMEDIUM;
2812                         tasklet_schedule(&host->finish_tasklet);
2813                 }
2814
2815                 spin_unlock_irqrestore(&host->lock, flags);
2816         }
2817
2818         sdhci_disable_card_detection(host);
2819
2820         mmc_remove_host(host->mmc);
2821
2822 #ifdef SDHCI_USE_LEDS_CLASS
2823         led_classdev_unregister(&host->led);
2824 #endif
2825
2826         if (!dead)
2827                 sdhci_reset(host, SDHCI_RESET_ALL);
2828
2829         free_irq(host->irq, host);
2830
2831         del_timer_sync(&host->timer);
2832         if (host->version >= SDHCI_SPEC_300)
2833                 del_timer_sync(&host->tuning_timer);
2834
2835         tasklet_kill(&host->card_tasklet);
2836         tasklet_kill(&host->finish_tasklet);
2837
2838         if (host->vmmc) {
2839                 regulator_disable(host->vmmc);
2840                 regulator_put(host->vmmc);
2841         }
2842
2843         kfree(host->adma_desc);
2844         kfree(host->align_buffer);
2845
2846         host->adma_desc = NULL;
2847         host->align_buffer = NULL;
2848 }
2849
2850 EXPORT_SYMBOL_GPL(sdhci_remove_host);
2851
2852 void sdhci_free_host(struct sdhci_host *host)
2853 {
2854         mmc_free_host(host->mmc);
2855 }
2856
2857 EXPORT_SYMBOL_GPL(sdhci_free_host);
2858
2859 /*****************************************************************************\
2860  *                                                                           *
2861  * Driver init/exit                                                          *
2862  *                                                                           *
2863 \*****************************************************************************/
2864
2865 static int __init sdhci_drv_init(void)
2866 {
2867         printk(KERN_INFO DRIVER_NAME
2868                 ": Secure Digital Host Controller Interface driver\n");
2869         printk(KERN_INFO DRIVER_NAME ": Copyright(c) Pierre Ossman\n");
2870
2871         return 0;
2872 }
2873
2874 static void __exit sdhci_drv_exit(void)
2875 {
2876 }
2877
2878 module_init(sdhci_drv_init);
2879 module_exit(sdhci_drv_exit);
2880
2881 module_param(debug_quirks, uint, 0444);
2882
2883 MODULE_AUTHOR("Pierre Ossman <pierre@ossman.eu>");
2884 MODULE_DESCRIPTION("Secure Digital Host Controller Interface core driver");
2885 MODULE_LICENSE("GPL");
2886
2887 MODULE_PARM_DESC(debug_quirks, "Force certain quirks.");