1 menu "Self-contained MTD device drivers"
6 tristate "Ramix PMC551 PCI Mezzanine RAM card support"
9 This provides a MTD device driver for the Ramix PMC551 RAM PCI card
10 from Ramix Inc. <http://www.ramix.com/products/memory/pmc551.html>.
11 These devices come in memory configurations from 32M - 1G. If you
12 have one, you probably want to enable this.
14 If this driver is compiled as a module you get the ability to select
15 the size of the aperture window pointing into the devices memory.
16 What this means is that if you have a 1G card, normally the kernel
17 will use a 1G memory map as its view of the device. As a module,
18 you can select a 1M window into the memory and the driver will
19 "slide" the window around the PMC551's memory. This was
20 particularly useful on the 2.2 kernels on PPC architectures as there
21 was limited kernel space to deal with.
23 config MTD_PMC551_BUGFIX
24 bool "PMC551 256M DRAM Bugfix"
27 Some of Ramix's PMC551 boards with 256M configurations have invalid
28 column and row mux values. This option will fix them, but will
29 break other memory configurations. If unsure say N.
31 config MTD_PMC551_DEBUG
32 bool "PMC551 Debugging"
35 This option makes the PMC551 more verbose during its operation and
36 is only really useful if you are developing on this driver or
37 suspect a possible hardware or driver bug. If unsure say N.
40 tristate "DEC MS02-NV NVRAM module support"
41 depends on MACH_DECSTATION
43 This is an MTD driver for the DEC's MS02-NV (54-20948-01) battery
44 backed-up NVRAM module. The module was originally meant as an NFS
45 accelerator. Say Y here if you have a DECstation 5000/2x0 or a
46 DECsystem 5900 equipped with such a module.
48 If you want to compile this driver as a module ( = code which can be
49 inserted in and removed from the running kernel whenever you want),
50 say M here and read <file:Documentation/kbuild/modules.txt>.
51 The module will be called ms02-nv.
54 tristate "Support for AT45xxx DataFlash"
57 This enables access to AT45xxx DataFlash chips, using SPI.
58 Sometimes DataFlash chips are packaged inside MMC-format
59 cards; at this writing, the MMC stack won't handle those.
61 config MTD_DATAFLASH_WRITE_VERIFY
62 bool "Verify DataFlash page writes"
63 depends on MTD_DATAFLASH
65 This adds an extra check when data is written to the flash.
66 It may help if you are verifying chip setup (timings etc) on
67 your board. There is a rare possibility that even though the
68 device thinks the write was successful, a bit could have been
69 flipped accidentally due to device wear or something else.
71 config MTD_DATAFLASH_OTP
72 bool "DataFlash OTP support (Security Register)"
73 depends on MTD_DATAFLASH
76 Newer DataFlash chips (revisions C and D) support 128 bytes of
77 one-time-programmable (OTP) data. The first half may be written
78 (once) with up to 64 bytes of data, such as a serial number or
79 other key product data. The second half is programmed with a
80 unique-to-each-chip bit pattern at the factory.
83 tristate "Support most SPI Flash chips (AT26DF, M25P, W25X, ...)"
86 This enables access to most modern SPI flash chips, used for
87 program and data storage. Series supported include Atmel AT26DF,
88 Spansion S25SL, SST 25VF, ST M25P, and Winbond W25X. Other chips
89 are supported as well. See the driver source for the current list,
90 or to add other chips.
92 Note that the original DataFlash chips (AT45 series, not AT26DF),
93 need an entirely different driver.
95 Set up your spi devices with the right board-specific platform data,
96 if you want to specify device partitioning or to use a device which
97 doesn't support the JEDEC ID instruction.
99 config M25PXX_USE_FAST_READ
100 bool "Use FAST_READ OPCode allowing SPI CLK >= 50MHz"
101 depends on MTD_M25P80
104 This option enables FAST_READ access supported by ST M25Pxx.
107 tristate "SPEAR MTD NOR Support through SMI controller"
108 depends on PLAT_SPEAR
111 This enable SNOR support on SPEAR platforms using SMI controller
114 tristate "Support SST25L (non JEDEC) SPI Flash chips"
115 depends on SPI_MASTER
117 This enables access to the non JEDEC SST25L SPI flash chips, used
118 for program and data storage.
120 Set up your spi devices with the right board-specific platform data,
121 if you want to specify device partitioning.
123 config MTD_BCM47XXSFLASH
124 tristate "R/O support for serial flash on BCMA bus"
125 depends on BCMA_SFLASH
127 BCMA bus can have various flash memories attached, they are
128 registered by bcma as platform devices. This enables driver for
129 serial flash memories (only read-only mode is implemented).
132 tristate "Uncached system RAM"
134 If your CPU cannot cache all of the physical memory in your machine,
135 you can still use it for storage or swap by using this driver to
136 present it to the system as a Memory Technology Device.
139 tristate "Physical system RAM"
141 This is a re-implementation of the slram driver above.
143 Use this driver to access physical memory that the kernel proper
144 doesn't have access to, memory beyond the mem=xxx limit, nvram,
145 memory on the video card, etc...
148 tristate "28F160xx flash driver for LART"
149 depends on SA1100_LART
151 This enables the flash driver for LART. Please note that you do
152 not need any mapping/chip driver for LART. This one does it all
153 for you, so go disable all of those if you enabled some of them (:
156 tristate "Test driver using RAM"
158 This enables a test MTD device driver which uses vmalloc() to
159 provide storage. You probably want to say 'N' unless you're
162 config MTDRAM_TOTAL_SIZE
163 int "MTDRAM device size in KiB"
164 depends on MTD_MTDRAM
167 This allows you to configure the total size of the MTD device
168 emulated by the MTDRAM driver. If the MTDRAM driver is built
169 as a module, it is also possible to specify this as a parameter when
172 config MTDRAM_ERASE_SIZE
173 int "MTDRAM erase block size in KiB"
174 depends on MTD_MTDRAM
177 This allows you to configure the size of the erase blocks in the
178 device emulated by the MTDRAM driver. If the MTDRAM driver is built
179 as a module, it is also possible to specify this as a parameter when
182 #If not a module (I don't want to test it as a module)
183 config MTDRAM_ABS_POS
184 hex "SRAM Hexadecimal Absolute position or 0"
185 depends on MTD_MTDRAM=y
188 If you have system RAM accessible by the CPU but not used by Linux
189 in normal operation, you can give the physical address at which the
190 available RAM starts, and the MTDRAM driver will use it instead of
191 allocating space from Linux's available memory. Otherwise, leave
192 this set to zero. Most people will want to leave this as zero.
195 tristate "MTD using block device"
198 This driver allows a block device to appear as an MTD. It would
199 generally be used in the following cases:
201 Using Compact Flash as an MTD, these usually present themselves to
202 the system as an ATA drive.
203 Testing MTD users (eg JFFS2) on large media and media that might
204 be removed during a write (using the floppy drive).
206 comment "Disk-On-Chip Device Drivers"
209 tristate "M-Systems Disk-On-Chip G3"
211 select BCH_CONST_PARAMS
214 This provides an MTD device driver for the M-Systems DiskOnChip
217 The driver provides access to G3 DiskOnChip, distributed by
218 M-Systems and now Sandisk. The support is very experimental,
219 and doesn't give access to any write operations.
235 config MTD_DOCPROBE_ADVANCED
236 bool "Advanced detection options for DiskOnChip"
237 depends on MTD_DOCPROBE
239 This option allows you to specify nonstandard address at which to
240 probe for a DiskOnChip, or to change the detection options. You
241 are unlikely to need any of this unless you are using LinuxBIOS.
244 config MTD_DOCPROBE_ADDRESS
245 hex "Physical address of DiskOnChip" if MTD_DOCPROBE_ADVANCED
246 depends on MTD_DOCPROBE
249 By default, the probe for DiskOnChip devices will look for a
250 DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
251 This option allows you to specify a single address at which to probe
252 for the device, which is useful if you have other devices in that
253 range which get upset when they are probed.
255 (Note that on PowerPC, the normal probe will only check at
258 Normally, you should leave this set to zero, to allow the probe at
259 the normal addresses.
261 config MTD_DOCPROBE_HIGH
262 bool "Probe high addresses"
263 depends on MTD_DOCPROBE_ADVANCED
265 By default, the probe for DiskOnChip devices will look for a
266 DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
267 This option changes to make it probe between 0xFFFC8000 and
268 0xFFFEE000. Unless you are using LinuxBIOS, this is unlikely to be
269 useful to you. Say 'N'.
271 config MTD_DOCPROBE_55AA
272 bool "Probe for 0x55 0xAA BIOS Extension Signature"
273 depends on MTD_DOCPROBE_ADVANCED
275 Check for the 0x55 0xAA signature of a DiskOnChip, and do not
276 continue with probing if it is absent. The signature will always be
277 present for a DiskOnChip 2000 or a normal DiskOnChip Millennium.
278 Only if you have overwritten the first block of a DiskOnChip
279 Millennium will it be absent. Enable this option if you are using
280 LinuxBIOS or if you need to recover a DiskOnChip Millennium on which
281 you have managed to wipe the first block.