drivers/scsi/wd719x.c

   1 /*
   2  * Driver for Western Digital WD7193, WD7197 and WD7296 SCSI cards
   3  * Copyright 2013 Ondrej Zary
   4  *
   5  * Original driver by
   6  * Aaron Dewell <dewell@woods.net>
   7  * Gaerti <Juergen.Gaertner@mbox.si.uni-hannover.de>
   8  *
   9  * HW documentation available in book:
  10  *
  11  * SPIDER Command Protocol
  12  * by Chandru M. Sippy
  13  * SCSI Storage Products (MCP)
  14  * Western Digital Corporation
  15  * 09-15-95
  16  *
  17  * http://web.archive.org/web/20070717175254/http://sun1.rrzn.uni-hannover.de/gaertner.juergen/wd719x/Linux/Docu/Spider/
  18  */
  19
  20 /*
  21  * Driver workflow:
  22  * 1. SCSI command is transformed to SCB (Spider Control Block) by the
  23  *    queuecommand function.
  24  * 2. The address of the SCB is stored in a list to be able to access it, if
  25  *    something goes wrong.
  26  * 3. The address of the SCB is written to the Controller, which loads the SCB
  27  *    via BM-DMA and processes it.
  28  * 4. After it has finished, it generates an interrupt, and sets registers.
  29  *
  30  * flaws:
  31  *  - abort/reset functions
  32  *
  33  * ToDo:
  34  *  - tagged queueing
  35  */
  36
  37 #include <linux/interrupt.h>
  38 #include <linux/module.h>
  39 #include <linux/delay.h>
  40 #include <linux/pci.h>
  41 #include <linux/firmware.h>
  42 #include <linux/eeprom_93cx6.h>
  43 #include <scsi/scsi_cmnd.h>
  44 #include <scsi/scsi_device.h>
  45 #include <scsi/scsi_host.h>
  46 #include "wd719x.h"
  47
  48 /* low-level register access */
  49 static inline u8 wd719x_readb(struct wd719x *wd, u8 reg)
  50 {
  51         return ioread8(wd->base + reg);
  52 }
  53
  54 static inline u32 wd719x_readl(struct wd719x *wd, u8 reg)
  55 {
  56         return ioread32(wd->base + reg);
  57 }
  58
  59 static inline void wd719x_writeb(struct wd719x *wd, u8 reg, u8 val)
  60 {
  61         iowrite8(val, wd->base + reg);
  62 }
  63
  64 static inline void wd719x_writew(struct wd719x *wd, u8 reg, u16 val)
  65 {
  66         iowrite16(val, wd->base + reg);
  67 }
  68
  69 static inline void wd719x_writel(struct wd719x *wd, u8 reg, u32 val)
  70 {
  71         iowrite32(val, wd->base + reg);
  72 }
  73
  74 /* wait until the command register is ready */
  75 static inline int wd719x_wait_ready(struct wd719x *wd)
  76 {
  77         int i = 0;
  78
  79         do {
  80                 if (wd719x_readb(wd, WD719X_AMR_COMMAND) == WD719X_CMD_READY)
  81                         return 0;
  82                 udelay(1);
  83         } while (i++ < WD719X_WAIT_FOR_CMD_READY);
  84
  85         dev_err(&wd->pdev->dev, "command register is not ready: 0x%02x\n",
  86                 wd719x_readb(wd, WD719X_AMR_COMMAND));
  87
  88         return -ETIMEDOUT;
  89 }
  90
  91 /* poll interrupt status register until command finishes */
  92 static inline int wd719x_wait_done(struct wd719x *wd, int timeout)
  93 {
  94         u8 status;
  95
  96         while (timeout > 0) {
  97                 status = wd719x_readb(wd, WD719X_AMR_INT_STATUS);
  98                 if (status)
  99                         break;
 100                 timeout--;
 101                 udelay(1);
 102         }
 103
 104         if (timeout <= 0) {
 105                 dev_err(&wd->pdev->dev, "direct command timed out\n");
 106                 return -ETIMEDOUT;
 107         }
 108
 109         if (status != WD719X_INT_NOERRORS) {
 110                 dev_err(&wd->pdev->dev, "direct command failed, status 0x%02x, SUE 0x%02x\n",
 111                         status, wd719x_readb(wd, WD719X_AMR_SCB_ERROR));
 112                 return -EIO;
 113         }
 114
 115         return 0;
 116 }
 117
 118 static int wd719x_direct_cmd(struct wd719x *wd, u8 opcode, u8 dev, u8 lun,
 119                              u8 tag, dma_addr_t data, int timeout)
 120 {
 121         int ret = 0;
 122
 123         /* clear interrupt status register (allow command register to clear) */
 124         wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE);
 125
 126         /* Wait for the Command register to become free */
 127         if (wd719x_wait_ready(wd))
 128                 return -ETIMEDOUT;
 129
 130         /* make sure we get NO interrupts */
 131         dev |= WD719X_DISABLE_INT;
 132         wd719x_writeb(wd, WD719X_AMR_CMD_PARAM, dev);
 133         wd719x_writeb(wd, WD719X_AMR_CMD_PARAM_2, lun);
 134         wd719x_writeb(wd, WD719X_AMR_CMD_PARAM_3, tag);
 135         if (data)
 136                 wd719x_writel(wd, WD719X_AMR_SCB_IN, data);
 137
 138         /* clear interrupt status register again */
 139         wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE);
 140
 141         /* Now, write the command */
 142         wd719x_writeb(wd, WD719X_AMR_COMMAND, opcode);
 143
 144         if (timeout)    /* wait for the command to complete */
 145                 ret = wd719x_wait_done(wd, timeout);
 146
 147         /* clear interrupt status register (clean up) */
 148         if (opcode != WD719X_CMD_READ_FIRMVER)
 149                 wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE);
 150
 151         return ret;
 152 }
 153
 154 static void wd719x_destroy(struct wd719x *wd)
 155 {
 156         struct wd719x_scb *scb;
 157
 158         /* stop the RISC */
 159         if (wd719x_direct_cmd(wd, WD719X_CMD_SLEEP, 0, 0, 0, 0,
 160                               WD719X_WAIT_FOR_RISC))
 161                 dev_warn(&wd->pdev->dev, "RISC sleep command failed\n");
 162         /* disable RISC */
 163         wd719x_writeb(wd, WD719X_PCI_MODE_SELECT, 0);
 164
 165         /* free all SCBs */
 166         list_for_each_entry(scb, &wd->active_scbs, list)
 167                 pci_free_consistent(wd->pdev, sizeof(struct wd719x_scb), scb,
 168                                     scb->phys);
 169         list_for_each_entry(scb, &wd->free_scbs, list)
 170                 pci_free_consistent(wd->pdev, sizeof(struct wd719x_scb), scb,
 171                                     scb->phys);
 172         /* free internal buffers */
 173         pci_free_consistent(wd->pdev, wd->fw_size, wd->fw_virt, wd->fw_phys);
 174         wd->fw_virt = NULL;
 175         pci_free_consistent(wd->pdev, WD719X_HASH_TABLE_SIZE, wd->hash_virt,
 176                             wd->hash_phys);
 177         wd->hash_virt = NULL;
 178         pci_free_consistent(wd->pdev, sizeof(struct wd719x_host_param),
 179                             wd->params, wd->params_phys);
 180         wd->params = NULL;
 181         free_irq(wd->pdev->irq, wd);
 182 }
 183
 184 /* finish a SCSI command, mark SCB (if any) as free, unmap buffers */
 185 static void wd719x_finish_cmd(struct scsi_cmnd *cmd, int result)
 186 {
 187         struct wd719x *wd = shost_priv(cmd->device->host);
 188         struct wd719x_scb *scb = (struct wd719x_scb *) cmd->host_scribble;
 189
 190         if (scb) {
 191                 list_move(&scb->list, &wd->free_scbs);
 192                 dma_unmap_single(&wd->pdev->dev, cmd->SCp.dma_handle,
 193                                  SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE);
 194                 scsi_dma_unmap(cmd);
 195         }
 196         cmd->result = result << 16;
 197         cmd->scsi_done(cmd);
 198 }
 199
 200 /* Build a SCB and send it to the card */
 201 static int wd719x_queuecommand(struct Scsi_Host *sh, struct scsi_cmnd *cmd)
 202 {
 203         int i, count_sg;
 204         unsigned long flags;
 205         struct wd719x_scb *scb;
 206         struct wd719x *wd = shost_priv(sh);
 207         dma_addr_t phys;
 208
 209         cmd->host_scribble = NULL;
 210
 211         /* get a free SCB - either from existing ones or allocate a new one */
 212         spin_lock_irqsave(wd->sh->host_lock, flags);
 213         scb = list_first_entry_or_null(&wd->free_scbs, struct wd719x_scb, list);
 214         if (scb) {
 215                 list_del(&scb->list);
 216                 phys = scb->phys;
 217         } else {
 218                 spin_unlock_irqrestore(wd->sh->host_lock, flags);
 219                 scb = pci_alloc_consistent(wd->pdev, sizeof(struct wd719x_scb),
 220                                            &phys);
 221                 spin_lock_irqsave(wd->sh->host_lock, flags);
 222                 if (!scb) {
 223                         dev_err(&wd->pdev->dev, "unable to allocate SCB\n");
 224                         wd719x_finish_cmd(cmd, DID_ERROR);
 225                         spin_unlock_irqrestore(wd->sh->host_lock, flags);
 226                         return 0;
 227                 }
 228         }
 229         memset(scb, 0, sizeof(struct wd719x_scb));
 230         list_add(&scb->list, &wd->active_scbs);
 231
 232         scb->phys = phys;
 233         scb->cmd = cmd;
 234         cmd->host_scribble = (char *) scb;
 235
 236         scb->CDB_tag = 0;       /* Tagged queueing not supported yet */
 237         scb->devid = cmd->device->id;
 238         scb->lun = cmd->device->lun;
 239
 240         /* copy the command */
 241         memcpy(scb->CDB, cmd->cmnd, cmd->cmd_len);
 242
 243         /* map sense buffer */
 244         scb->sense_buf_length = SCSI_SENSE_BUFFERSIZE;
 245         cmd->SCp.dma_handle = dma_map_single(&wd->pdev->dev, cmd->sense_buffer,
 246                         SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE);
 247         scb->sense_buf = cpu_to_le32(cmd->SCp.dma_handle);
 248
 249         /* request autosense */
 250         scb->SCB_options |= WD719X_SCB_FLAGS_AUTO_REQUEST_SENSE;
 251
 252         /* check direction */
 253         if (cmd->sc_data_direction == DMA_TO_DEVICE)
 254                 scb->SCB_options |= WD719X_SCB_FLAGS_CHECK_DIRECTION
 255                                  |  WD719X_SCB_FLAGS_PCI_TO_SCSI;
 256         else if (cmd->sc_data_direction == DMA_FROM_DEVICE)
 257                 scb->SCB_options |= WD719X_SCB_FLAGS_CHECK_DIRECTION;
 258
 259         /* Scather/gather */
 260         count_sg = scsi_dma_map(cmd);
 261         if (count_sg < 0) {
 262                 wd719x_finish_cmd(cmd, DID_ERROR);
 263                 spin_unlock_irqrestore(wd->sh->host_lock, flags);
 264                 return 0;
 265         }
 266         BUG_ON(count_sg > WD719X_SG);
 267
 268         if (count_sg) {
 269                 struct scatterlist *sg;
 270
 271                 scb->data_length = cpu_to_le32(count_sg *
 272                                                sizeof(struct wd719x_sglist));
 273                 scb->data_p = cpu_to_le32(scb->phys +
 274                                           offsetof(struct wd719x_scb, sg_list));
 275
 276                 scsi_for_each_sg(cmd, sg, count_sg, i) {
 277                         scb->sg_list[i].ptr = cpu_to_le32(sg_dma_address(sg));
 278                         scb->sg_list[i].length = cpu_to_le32(sg_dma_len(sg));
 279                 }
 280                 scb->SCB_options |= WD719X_SCB_FLAGS_DO_SCATTER_GATHER;
 281         } else { /* zero length */
 282                 scb->data_length = 0;
 283                 scb->data_p = 0;
 284         }
 285
 286         /* check if the Command register is free */
 287         if (wd719x_readb(wd, WD719X_AMR_COMMAND) != WD719X_CMD_READY) {
 288                 spin_unlock_irqrestore(wd->sh->host_lock, flags);
 289                 return SCSI_MLQUEUE_HOST_BUSY;
 290         }
 291
 292         /* write pointer to the AMR */
 293         wd719x_writel(wd, WD719X_AMR_SCB_IN, scb->phys);
 294         /* send SCB opcode */
 295         wd719x_writeb(wd, WD719X_AMR_COMMAND, WD719X_CMD_PROCESS_SCB);
 296
 297         spin_unlock_irqrestore(wd->sh->host_lock, flags);
 298
 299         return 0;
 300 }
 301
 302 static int wd719x_chip_init(struct wd719x *wd)
 303 {
 304         int i, ret;
 305         u32 risc_init[3];
 306         const struct firmware *fw_wcs, *fw_risc;
 307         const char fwname_wcs[] = "wd719x-wcs.bin";
 308         const char fwname_risc[] = "wd719x-risc.bin";
 309
 310         memset(wd->hash_virt, 0, WD719X_HASH_TABLE_SIZE);
 311
 312         /* WCS (sequencer) firmware */
 313         ret = request_firmware(&fw_wcs, fwname_wcs, &wd->pdev->dev);
 314         if (ret) {
 315                 dev_err(&wd->pdev->dev, "Unable to load firmware %s: %d\n",
 316                         fwname_wcs, ret);
 317                 return ret;
 318         }
 319         /* RISC firmware */
 320         ret = request_firmware(&fw_risc, fwname_risc, &wd->pdev->dev);
 321         if (ret) {
 322                 dev_err(&wd->pdev->dev, "Unable to load firmware %s: %d\n",
 323                         fwname_risc, ret);
 324                 release_firmware(fw_wcs);
 325                 return ret;
 326         }
 327         wd->fw_size = ALIGN(fw_wcs->size, 4) + fw_risc->size;
 328
 329         if (!wd->fw_virt)
 330                 wd->fw_virt = pci_alloc_consistent(wd->pdev, wd->fw_size,
 331                                                    &wd->fw_phys);
 332         if (!wd->fw_virt) {
 333                 ret = -ENOMEM;
 334                 goto wd719x_init_end;
 335         }
 336
 337         /* make a fresh copy of WCS and RISC code */
 338         memcpy(wd->fw_virt, fw_wcs->data, fw_wcs->size);
 339         memcpy(wd->fw_virt + ALIGN(fw_wcs->size, 4), fw_risc->data,
 340                 fw_risc->size);
 341
 342         /* Reset the Spider Chip and adapter itself */
 343         wd719x_writeb(wd, WD719X_PCI_PORT_RESET, WD719X_PCI_RESET);
 344         udelay(WD719X_WAIT_FOR_RISC);
 345         /* Clear PIO mode bits set by BIOS */
 346         wd719x_writeb(wd, WD719X_AMR_CMD_PARAM, 0);
 347         /* ensure RISC is not running */
 348         wd719x_writeb(wd, WD719X_PCI_MODE_SELECT, 0);
 349         /* ensure command port is ready */
 350         wd719x_writeb(wd, WD719X_AMR_COMMAND, 0);
 351         if (wd719x_wait_ready(wd)) {
 352                 ret = -ETIMEDOUT;
 353                 goto wd719x_init_end;
 354         }
 355
 356         /* Transfer the first 2K words of RISC code to kick start the uP */
 357         risc_init[0] = wd->fw_phys;                             /* WCS FW */
 358         risc_init[1] = wd->fw_phys + ALIGN(fw_wcs->size, 4);    /* RISC FW */
 359         risc_init[2] = wd->hash_phys;                           /* hash table */
 360
 361         /* clear DMA status */
 362         wd719x_writeb(wd, WD719X_PCI_CHANNEL2_3STATUS, 0);
 363
 364         /* address to read firmware from */
 365         wd719x_writel(wd, WD719X_PCI_EXTERNAL_ADDR, risc_init[1]);
 366         /* base address to write firmware to (on card) */
 367         wd719x_writew(wd, WD719X_PCI_INTERNAL_ADDR, WD719X_PRAM_BASE_ADDR);
 368         /* size: first 2K words */
 369         wd719x_writew(wd, WD719X_PCI_DMA_TRANSFER_SIZE, 2048 * 2);
 370         /* start DMA */
 371         wd719x_writeb(wd, WD719X_PCI_CHANNEL2_3CMD, WD719X_START_CHANNEL2_3DMA);
 372
 373         /* wait for DMA to complete */
 374         i = WD719X_WAIT_FOR_RISC;
 375         while (i-- > 0) {
 376                 u8 status = wd719x_readb(wd, WD719X_PCI_CHANNEL2_3STATUS);
 377                 if (status == WD719X_START_CHANNEL2_3DONE)
 378                         break;
 379                 if (status == WD719X_START_CHANNEL2_3ABORT) {
 380                         dev_warn(&wd->pdev->dev, "RISC bootstrap failed: DMA aborted\n");
 381                         ret = -EIO;
 382                         goto wd719x_init_end;
 383                 }
 384                 udelay(1);
 385         }
 386         if (i < 1) {
 387                 dev_warn(&wd->pdev->dev, "RISC bootstrap failed: DMA timeout\n");
 388                 ret = -ETIMEDOUT;
 389                 goto wd719x_init_end;
 390         }
 391
 392         /* firmware is loaded, now initialize and wake up the RISC */
 393         /* write RISC initialization long words to Spider */
 394         wd719x_writel(wd, WD719X_AMR_SCB_IN, risc_init[0]);
 395         wd719x_writel(wd, WD719X_AMR_SCB_IN + 4, risc_init[1]);
 396         wd719x_writel(wd, WD719X_AMR_SCB_IN + 8, risc_init[2]);
 397
 398         /* disable interrupts during initialization of RISC */
 399         wd719x_writeb(wd, WD719X_AMR_CMD_PARAM, WD719X_DISABLE_INT);
 400
 401         /* issue INITIALIZE RISC comand */
 402         wd719x_writeb(wd, WD719X_AMR_COMMAND, WD719X_CMD_INIT_RISC);
 403         /* enable advanced mode (wake up RISC) */
 404         wd719x_writeb(wd, WD719X_PCI_MODE_SELECT, WD719X_ENABLE_ADVANCE_MODE);
 405         udelay(WD719X_WAIT_FOR_RISC);
 406
 407         ret = wd719x_wait_done(wd, WD719X_WAIT_FOR_RISC);
 408         /* clear interrupt status register */
 409         wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE);
 410         if (ret) {
 411                 dev_warn(&wd->pdev->dev, "Unable to initialize RISC\n");
 412                 goto wd719x_init_end;
 413         }
 414         /* RISC is up and running */
 415
 416         /* Read FW version from RISC */
 417         ret = wd719x_direct_cmd(wd, WD719X_CMD_READ_FIRMVER, 0, 0, 0, 0,
 418                                 WD719X_WAIT_FOR_RISC);
 419         if (ret) {
 420                 dev_warn(&wd->pdev->dev, "Unable to read firmware version\n");
 421                 goto wd719x_init_end;
 422         }
 423         dev_info(&wd->pdev->dev, "RISC initialized with firmware version %.2x.%.2x\n",
 424                         wd719x_readb(wd, WD719X_AMR_SCB_OUT + 1),
 425                         wd719x_readb(wd, WD719X_AMR_SCB_OUT));
 426
 427         /* RESET SCSI bus */
 428         ret = wd719x_direct_cmd(wd, WD719X_CMD_BUSRESET, 0, 0, 0, 0,
 429                                 WD719X_WAIT_FOR_SCSI_RESET);
 430         if (ret) {
 431                 dev_warn(&wd->pdev->dev, "SCSI bus reset failed\n");
 432                 goto wd719x_init_end;
 433         }
 434
 435         /* use HostParameter structure to set Spider's Host Parameter Block */
 436         ret = wd719x_direct_cmd(wd, WD719X_CMD_SET_PARAM, 0,
 437                                 sizeof(struct wd719x_host_param), 0,
 438                                 wd->params_phys, WD719X_WAIT_FOR_RISC);
 439         if (ret) {
 440                 dev_warn(&wd->pdev->dev, "Failed to set HOST PARAMETERS\n");
 441                 goto wd719x_init_end;
 442         }
 443
 444         /* initiate SCAM (does nothing if disabled in BIOS) */
 445         /* bug?: we should pass a mask of static IDs which we don't have */
 446         ret = wd719x_direct_cmd(wd, WD719X_CMD_INIT_SCAM, 0, 0, 0, 0,
 447                                 WD719X_WAIT_FOR_SCSI_RESET);
 448         if (ret) {
 449                 dev_warn(&wd->pdev->dev, "SCAM initialization failed\n");
 450                 goto wd719x_init_end;
 451         }
 452
 453         /* clear AMR_BIOS_SHARE_INT register */
 454         wd719x_writeb(wd, WD719X_AMR_BIOS_SHARE_INT, 0);
 455
 456 wd719x_init_end:
 457         release_firmware(fw_wcs);
 458         release_firmware(fw_risc);
 459
 460         return ret;
 461 }
 462
 463 static int wd719x_abort(struct scsi_cmnd *cmd)
 464 {
 465         int action, result;
 466         unsigned long flags;
 467         struct wd719x_scb *scb = (struct wd719x_scb *)cmd->host_scribble;
 468         struct wd719x *wd = shost_priv(cmd->device->host);
 469
 470         dev_info(&wd->pdev->dev, "abort command, tag: %x\n", cmd->tag);
 471
 472         action = /*cmd->tag ? WD719X_CMD_ABORT_TAG : */WD719X_CMD_ABORT;
 473
 474         spin_lock_irqsave(wd->sh->host_lock, flags);
 475         result = wd719x_direct_cmd(wd, action, cmd->device->id,
 476                                    cmd->device->lun, cmd->tag, scb->phys, 0);
 477         spin_unlock_irqrestore(wd->sh->host_lock, flags);
 478         if (result)
 479                 return FAILED;
 480
 481         return SUCCESS;
 482 }
 483
 484 static int wd719x_reset(struct scsi_cmnd *cmd, u8 opcode, u8 device)
 485 {
 486         int result;
 487         unsigned long flags;
 488         struct wd719x *wd = shost_priv(cmd->device->host);
 489
 490         dev_info(&wd->pdev->dev, "%s reset requested\n",
 491                  (opcode == WD719X_CMD_BUSRESET) ? "bus" : "device");
 492
 493         spin_lock_irqsave(wd->sh->host_lock, flags);
 494         result = wd719x_direct_cmd(wd, opcode, device, 0, 0, 0,
 495                                    WD719X_WAIT_FOR_SCSI_RESET);
 496         spin_unlock_irqrestore(wd->sh->host_lock, flags);
 497         if (result)
 498                 return FAILED;
 499
 500         return SUCCESS;
 501 }
 502
 503 static int wd719x_dev_reset(struct scsi_cmnd *cmd)
 504 {
 505         return wd719x_reset(cmd, WD719X_CMD_RESET, cmd->device->id);
 506 }
 507
 508 static int wd719x_bus_reset(struct scsi_cmnd *cmd)
 509 {
 510         return wd719x_reset(cmd, WD719X_CMD_BUSRESET, 0);
 511 }
 512
 513 static int wd719x_host_reset(struct scsi_cmnd *cmd)
 514 {
 515         struct wd719x *wd = shost_priv(cmd->device->host);
 516         struct wd719x_scb *scb, *tmp;
 517         unsigned long flags;
 518         int result;
 519
 520         dev_info(&wd->pdev->dev, "host reset requested\n");
 521         spin_lock_irqsave(wd->sh->host_lock, flags);
 522         /* Try to reinit the RISC */
 523         if (wd719x_chip_init(wd) == 0)
 524                 result = SUCCESS;
 525         else
 526                 result = FAILED;
 527
 528         /* flush all SCBs */
 529         list_for_each_entry_safe(scb, tmp, &wd->active_scbs, list) {
 530                 struct scsi_cmnd *tmp_cmd = scb->cmd;
 531                 wd719x_finish_cmd(tmp_cmd, result);
 532         }
 533         spin_unlock_irqrestore(wd->sh->host_lock, flags);
 534
 535         return result;
 536 }
 537
 538 static int wd719x_biosparam(struct scsi_device *sdev, struct block_device *bdev,
 539                             sector_t capacity, int geom[])
 540 {
 541         if (capacity >= 0x200000) {
 542                 geom[0] = 255;  /* heads */
 543                 geom[1] = 63;   /* sectors */
 544         } else {
 545                 geom[0] = 64;   /* heads */
 546                 geom[1] = 32;   /* sectors */
 547         }
 548         geom[2] = sector_div(capacity, geom[0] * geom[1]);      /* cylinders */
 549
 550         return 0;
 551 }
 552
 553 /* process a SCB-completion interrupt */
 554 static inline void wd719x_interrupt_SCB(struct wd719x *wd,
 555                                         union wd719x_regs regs,
 556                                         struct wd719x_scb *scb)
 557 {
 558         struct scsi_cmnd *cmd;
 559         int result;
 560
 561         /* now have to find result from card */
 562         switch (regs.bytes.SUE) {
 563         case WD719X_SUE_NOERRORS:
 564                 result = DID_OK;
 565                 break;
 566         case WD719X_SUE_REJECTED:
 567                 dev_err(&wd->pdev->dev, "command rejected\n");
 568                 result = DID_ERROR;
 569                 break;
 570         case WD719X_SUE_SCBQFULL:
 571                 dev_err(&wd->pdev->dev, "SCB queue is full\n");
 572                 result = DID_ERROR;
 573                 break;
 574         case WD719X_SUE_TERM:
 575                 dev_dbg(&wd->pdev->dev, "SCB terminated by direct command\n");
 576                 result = DID_ABORT;     /* or DID_RESET? */
 577                 break;
 578         case WD719X_SUE_CHAN1ABORT:
 579         case WD719X_SUE_CHAN23ABORT:
 580                 result = DID_ABORT;
 581                 dev_err(&wd->pdev->dev, "DMA abort\n");
 582                 break;
 583         case WD719X_SUE_CHAN1PAR:
 584         case WD719X_SUE_CHAN23PAR:
 585                 result = DID_PARITY;
 586                 dev_err(&wd->pdev->dev, "DMA parity error\n");
 587                 break;
 588         case WD719X_SUE_TIMEOUT:
 589                 result = DID_TIME_OUT;
 590                 dev_dbg(&wd->pdev->dev, "selection timeout\n");
 591                 break;
 592         case WD719X_SUE_RESET:
 593                 dev_dbg(&wd->pdev->dev, "bus reset occured\n");
 594                 result = DID_RESET;
 595                 break;
 596         case WD719X_SUE_BUSERROR:
 597                 dev_dbg(&wd->pdev->dev, "SCSI bus error\n");
 598                 result = DID_ERROR;
 599                 break;
 600         case WD719X_SUE_WRONGWAY:
 601                 dev_err(&wd->pdev->dev, "wrong data transfer direction\n");
 602                 result = DID_ERROR;
 603                 break;
 604         case WD719X_SUE_BADPHASE:
 605                 dev_err(&wd->pdev->dev, "invalid SCSI phase\n");
 606                 result = DID_ERROR;
 607                 break;
 608         case WD719X_SUE_TOOLONG:
 609                 dev_err(&wd->pdev->dev, "record too long\n");
 610                 result = DID_ERROR;
 611                 break;
 612         case WD719X_SUE_BUSFREE:
 613                 dev_err(&wd->pdev->dev, "unexpected bus free\n");
 614                 result = DID_NO_CONNECT; /* or DID_ERROR ???*/
 615                 break;
 616         case WD719X_SUE_ARSDONE:
 617                 dev_dbg(&wd->pdev->dev, "auto request sense\n");
 618                 if (regs.bytes.SCSI == 0)
 619                         result = DID_OK;
 620                 else
 621                         result = DID_PARITY;
 622                 break;
 623         case WD719X_SUE_IGNORED:
 624                 dev_err(&wd->pdev->dev, "target id %d ignored command\n",
 625                         scb->cmd->device->id);
 626                 result = DID_NO_CONNECT;
 627                 break;
 628         case WD719X_SUE_WRONGTAGS:
 629                 dev_err(&wd->pdev->dev, "reversed tags\n");
 630                 result = DID_ERROR;
 631                 break;
 632         case WD719X_SUE_BADTAGS:
 633                 dev_err(&wd->pdev->dev, "tag type not supported by target\n");
 634                 result = DID_ERROR;
 635                 break;
 636         case WD719X_SUE_NOSCAMID:
 637                 dev_err(&wd->pdev->dev, "no SCAM soft ID available\n");
 638                 result = DID_ERROR;
 639                 break;
 640         default:
 641                 dev_warn(&wd->pdev->dev, "unknown SUE error code: 0x%x\n",
 642                          regs.bytes.SUE);
 643                 result = DID_ERROR;
 644                 break;
 645         }
 646         cmd = scb->cmd;
 647
 648         wd719x_finish_cmd(cmd, result);
 649 }
 650
 651 static irqreturn_t wd719x_interrupt(int irq, void *dev_id)
 652 {
 653         struct wd719x *wd = dev_id;
 654         union wd719x_regs regs;
 655         unsigned long flags;
 656         u32 SCB_out;
 657
 658         spin_lock_irqsave(wd->sh->host_lock, flags);
 659         /* read SCB pointer back from card */
 660         SCB_out = wd719x_readl(wd, WD719X_AMR_SCB_OUT);
 661         /* read all status info at once */
 662         regs.all = cpu_to_le32(wd719x_readl(wd, WD719X_AMR_OP_CODE));
 663
 664         switch (regs.bytes.INT) {
 665         case WD719X_INT_NONE:
 666                 spin_unlock_irqrestore(wd->sh->host_lock, flags);
 667                 return IRQ_NONE;
 668         case WD719X_INT_LINKNOSTATUS:
 669                 dev_err(&wd->pdev->dev, "linked command completed with no status\n");
 670                 break;
 671         case WD719X_INT_BADINT:
 672                 dev_err(&wd->pdev->dev, "unsolicited interrupt\n");
 673                 break;
 674         case WD719X_INT_NOERRORS:
 675         case WD719X_INT_LINKNOERRORS:
 676         case WD719X_INT_ERRORSLOGGED:
 677         case WD719X_INT_SPIDERFAILED:
 678                 /* was the cmd completed a direct or SCB command? */
 679                 if (regs.bytes.OPC == WD719X_CMD_PROCESS_SCB) {
 680                         struct wd719x_scb *scb;
 681                         list_for_each_entry(scb, &wd->active_scbs, list)
 682                                 if (SCB_out == scb->phys)
 683                                         break;
 684                         if (SCB_out == scb->phys)
 685                                 wd719x_interrupt_SCB(wd, regs, scb);
 686                         else
 687                                 dev_err(&wd->pdev->dev, "card returned invalid SCB pointer\n");
 688                 } else
 689                         dev_warn(&wd->pdev->dev, "direct command 0x%x completed\n",
 690                                  regs.bytes.OPC);
 691                 break;
 692         case WD719X_INT_PIOREADY:
 693                 dev_err(&wd->pdev->dev, "card indicates PIO data ready but we never use PIO\n");
 694                 /* interrupt will not be cleared until all data is read */
 695                 break;
 696         default:
 697                 dev_err(&wd->pdev->dev, "unknown interrupt reason: %d\n",
 698                         regs.bytes.INT);
 699
 700         }
 701         /* clear interrupt so another can happen */
 702         wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE);
 703         spin_unlock_irqrestore(wd->sh->host_lock, flags);
 704
 705         return IRQ_HANDLED;
 706 }
 707
 708 static void wd719x_eeprom_reg_read(struct eeprom_93cx6 *eeprom)
 709 {
 710         struct wd719x *wd = eeprom->data;
 711         u8 reg = wd719x_readb(wd, WD719X_PCI_GPIO_DATA);
 712
 713         eeprom->reg_data_out = reg & WD719X_EE_DO;
 714 }
 715
 716 static void wd719x_eeprom_reg_write(struct eeprom_93cx6 *eeprom)
 717 {
 718         struct wd719x *wd = eeprom->data;
 719         u8 reg = 0;
 720
 721         if (eeprom->reg_data_in)
 722                 reg |= WD719X_EE_DI;
 723         if (eeprom->reg_data_clock)
 724                 reg |= WD719X_EE_CLK;
 725         if (eeprom->reg_chip_select)
 726                 reg |= WD719X_EE_CS;
 727
 728         wd719x_writeb(wd, WD719X_PCI_GPIO_DATA, reg);
 729 }
 730
 731 /* read config from EEPROM so it can be downloaded by the RISC on (re-)init */
 732 static void wd719x_read_eeprom(struct wd719x *wd)
 733 {
 734         struct eeprom_93cx6 eeprom;
 735         u8 gpio;
 736         struct wd719x_eeprom_header header;
 737
 738         eeprom.data = wd;
 739         eeprom.register_read = wd719x_eeprom_reg_read;
 740         eeprom.register_write = wd719x_eeprom_reg_write;
 741         eeprom.width = PCI_EEPROM_WIDTH_93C46;
 742
 743         /* set all outputs to low */
 744         wd719x_writeb(wd, WD719X_PCI_GPIO_DATA, 0);
 745         /* configure GPIO pins */
 746         gpio = wd719x_readb(wd, WD719X_PCI_GPIO_CONTROL);
 747         /* GPIO outputs */
 748         gpio &= (~(WD719X_EE_CLK | WD719X_EE_DI | WD719X_EE_CS));
 749         /* GPIO input */
 750         gpio |= WD719X_EE_DO;
 751         wd719x_writeb(wd, WD719X_PCI_GPIO_CONTROL, gpio);
 752
 753         /* read EEPROM header */
 754         eeprom_93cx6_multireadb(&eeprom, 0, (u8 *)&header, sizeof(header));
 755
 756         if (header.sig1 == 'W' && header.sig2 == 'D')
 757                 eeprom_93cx6_multireadb(&eeprom, header.cfg_offset,
 758                                         (u8 *)wd->params,
 759                                         sizeof(struct wd719x_host_param));
 760         else { /* default EEPROM values */
 761                 dev_warn(&wd->pdev->dev, "EEPROM signature is invalid (0x%02x 0x%02x), using default values\n",
 762                          header.sig1, header.sig2);
 763                 wd->params->ch_1_th     = 0x10; /* 16 DWs = 64 B */
 764                 wd->params->scsi_conf   = 0x4c; /* 48ma, spue, parity check */
 765                 wd->params->own_scsi_id = 0x07; /* ID 7, SCAM disabled */
 766                 wd->params->sel_timeout = 0x4d; /* 250 ms */
 767                 wd->params->sleep_timer = 0x01;
 768                 wd->params->cdb_size    = cpu_to_le16(0x5555);  /* all 6 B */
 769                 wd->params->scsi_pad    = 0x1b;
 770                 if (wd->type == WD719X_TYPE_7193) /* narrow card - disable */
 771                         wd->params->wide = cpu_to_le32(0x00000000);
 772                 else    /* initiate & respond to WIDE messages */
 773                         wd->params->wide = cpu_to_le32(0xffffffff);
 774                 wd->params->sync        = cpu_to_le32(0xffffffff);
 775                 wd->params->soft_mask   = 0x00; /* all disabled */
 776                 wd->params->unsol_mask  = 0x00; /* all disabled */
 777         }
 778         /* disable TAGGED messages */
 779         wd->params->tag_en = cpu_to_le16(0x0000);
 780 }
 781
 782 /* Read card type from GPIO bits 1 and 3 */
 783 static enum wd719x_card_type wd719x_detect_type(struct wd719x *wd)
 784 {
 785         u8 card = wd719x_readb(wd, WD719X_PCI_GPIO_CONTROL);
 786
 787         card |= WD719X_GPIO_ID_BITS;
 788         wd719x_writeb(wd, WD719X_PCI_GPIO_CONTROL, card);
 789         card = wd719x_readb(wd, WD719X_PCI_GPIO_DATA) & WD719X_GPIO_ID_BITS;
 790         switch (card) {
 791         case 0x08:
 792                 return WD719X_TYPE_7193;
 793         case 0x02:
 794                 return WD719X_TYPE_7197;
 795         case 0x00:
 796                 return WD719X_TYPE_7296;
 797         default:
 798                 dev_warn(&wd->pdev->dev, "unknown card type 0x%x\n", card);
 799                 return WD719X_TYPE_UNKNOWN;
 800         }
 801 }
 802
 803 static int wd719x_board_found(struct Scsi_Host *sh)
 804 {
 805         struct wd719x *wd = shost_priv(sh);
 806         char *card_types[] = { "Unknown card", "WD7193", "WD7197", "WD7296" };
 807         int ret;
 808
 809         INIT_LIST_HEAD(&wd->active_scbs);
 810         INIT_LIST_HEAD(&wd->free_scbs);
 811
 812         sh->base = pci_resource_start(wd->pdev, 0);
 813
 814         wd->type = wd719x_detect_type(wd);
 815
 816         wd->sh = sh;
 817         sh->irq = wd->pdev->irq;
 818         wd->fw_virt = NULL;
 819
 820         /* memory area for host (EEPROM) parameters */
 821         wd->params = pci_alloc_consistent(wd->pdev,
 822                                           sizeof(struct wd719x_host_param),
 823                                           &wd->params_phys);
 824         if (!wd->params) {
 825                 dev_warn(&wd->pdev->dev, "unable to allocate parameter buffer\n");
 826                 return -ENOMEM;
 827         }
 828
 829         /* memory area for the RISC for hash table of outstanding requests */
 830         wd->hash_virt = pci_alloc_consistent(wd->pdev, WD719X_HASH_TABLE_SIZE,
 831                                              &wd->hash_phys);
 832         if (!wd->hash_virt) {
 833                 dev_warn(&wd->pdev->dev, "unable to allocate hash buffer\n");
 834                 ret = -ENOMEM;
 835                 goto fail_free_params;
 836         }
 837
 838         ret = request_irq(wd->pdev->irq, wd719x_interrupt, IRQF_SHARED,
 839                           "wd719x", wd);
 840         if (ret) {
 841                 dev_warn(&wd->pdev->dev, "unable to assign IRQ %d\n",
 842                          wd->pdev->irq);
 843                 goto fail_free_hash;
 844         }
 845
 846         /* read parameters from EEPROM */
 847         wd719x_read_eeprom(wd);
 848
 849         ret = wd719x_chip_init(wd);
 850         if (ret)
 851                 goto fail_free_irq;
 852
 853         sh->this_id = wd->params->own_scsi_id & WD719X_EE_SCSI_ID_MASK;
 854
 855         dev_info(&wd->pdev->dev, "%s at I/O 0x%lx, IRQ %u, SCSI ID %d\n",
 856                  card_types[wd->type], sh->base, sh->irq, sh->this_id);
 857
 858         return 0;
 859
 860 fail_free_irq:
 861         free_irq(wd->pdev->irq, wd);
 862 fail_free_hash:
 863         pci_free_consistent(wd->pdev, WD719X_HASH_TABLE_SIZE, wd->hash_virt,
 864                             wd->hash_phys);
 865 fail_free_params:
 866         pci_free_consistent(wd->pdev, sizeof(struct wd719x_host_param),
 867                             wd->params, wd->params_phys);
 868
 869         return ret;
 870 }
 871
 872 static struct scsi_host_template wd719x_template = {
 873         .name                           = "Western Digital 719x",
 874         .queuecommand                   = wd719x_queuecommand,
 875         .eh_abort_handler               = wd719x_abort,
 876         .eh_device_reset_handler        = wd719x_dev_reset,
 877         .eh_bus_reset_handler           = wd719x_bus_reset,
 878         .eh_host_reset_handler          = wd719x_host_reset,
 879         .bios_param                     = wd719x_biosparam,
 880         .proc_name                      = "wd719x",
 881         .can_queue                      = 255,
 882         .this_id                        = 7,
 883         .sg_tablesize                   = WD719X_SG,
 884         .cmd_per_lun                    = WD719X_CMD_PER_LUN,
 885         .use_clustering                 = ENABLE_CLUSTERING,
 886 };
 887
 888 static int wd719x_pci_probe(struct pci_dev *pdev, const struct pci_device_id *d)
 889 {
 890         int err;
 891         struct Scsi_Host *sh;
 892         struct wd719x *wd;
 893
 894         err = pci_enable_device(pdev);
 895         if (err)
 896                 goto fail;
 897
 898         if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
 899                 dev_warn(&pdev->dev, "Unable to set 32-bit DMA mask\n");
 900                 goto disable_device;
 901         }
 902
 903         err = pci_request_regions(pdev, "wd719x");
 904         if (err)
 905                 goto disable_device;
 906         pci_set_master(pdev);
 907
 908         err = -ENODEV;
 909         if (pci_resource_len(pdev, 0) == 0)
 910                 goto release_region;
 911
 912         err = -ENOMEM;
 913         sh = scsi_host_alloc(&wd719x_template, sizeof(struct wd719x));
 914         if (!sh)
 915                 goto release_region;
 916
 917         wd = shost_priv(sh);
 918         wd->base = pci_iomap(pdev, 0, 0);
 919         if (!wd->base)
 920                 goto free_host;
 921         wd->pdev = pdev;
 922
 923         err = wd719x_board_found(sh);
 924         if (err)
 925                 goto unmap;
 926
 927         err = scsi_add_host(sh, &wd->pdev->dev);
 928         if (err)
 929                 goto destroy;
 930
 931         scsi_scan_host(sh);
 932
 933         pci_set_drvdata(pdev, sh);
 934         return 0;
 935
 936 destroy:
 937         wd719x_destroy(wd);
 938 unmap:
 939         pci_iounmap(pdev, wd->base);
 940 free_host:
 941         scsi_host_put(sh);
 942 release_region:
 943         pci_release_regions(pdev);
 944 disable_device:
 945         pci_disable_device(pdev);
 946 fail:
 947         return err;
 948 }
 949
 950
 951 static void wd719x_pci_remove(struct pci_dev *pdev)
 952 {
 953         struct Scsi_Host *sh = pci_get_drvdata(pdev);
 954         struct wd719x *wd = shost_priv(sh);
 955
 956         scsi_remove_host(sh);
 957         wd719x_destroy(wd);
 958         pci_iounmap(pdev, wd->base);
 959         pci_release_regions(pdev);
 960         pci_disable_device(pdev);
 961
 962         scsi_host_put(sh);
 963 }
 964
 965 static DEFINE_PCI_DEVICE_TABLE(wd719x_pci_table) = {
 966         { PCI_DEVICE(PCI_VENDOR_ID_WD, 0x3296) },
 967         {}
 968 };
 969
 970 MODULE_DEVICE_TABLE(pci, wd719x_pci_table);
 971
 972 static struct pci_driver wd719x_pci_driver = {
 973         .name =         "wd719x",
 974         .id_table =     wd719x_pci_table,
 975         .probe =        wd719x_pci_probe,
 976         .remove =       wd719x_pci_remove,
 977 };
 978
 979 static int __init wd719x_init(void)
 980 {
 981         return pci_register_driver(&wd719x_pci_driver);
 982 }
 983
 984 static void __exit wd719x_exit(void)
 985 {
 986         pci_unregister_driver(&wd719x_pci_driver);
 987 }
 988
 989 module_init(wd719x_init);
 990 module_exit(wd719x_exit);
 991
 992 MODULE_DESCRIPTION("Western Digital WD7193/7197/7296 SCSI driver");
 993 MODULE_AUTHOR("Ondrej Zary, Aaron Dewell, Juergen Gaertner");
 994 MODULE_LICENSE("GPL");
 995 MODULE_FIRMWARE("wd719x-wcs.bin");
 996 MODULE_FIRMWARE("wd719x-risc.bin");