2 # SPI driver configuration
4 # NOTE: the reason this doesn't show SPI slave support is mostly that
5 # nobody's needed a slave side API yet. The master-role API is not
6 # fully appropriate there, so it'd need some thought to do well.
12 The "Serial Peripheral Interface" is a low level synchronous
13 protocol. Chips that support SPI can have data transfer rates
14 up to several tens of Mbit/sec. Chips are addressed with a
15 controller and a chipselect. Most SPI slaves don't support
16 dynamic device discovery; some are even write-only or read-only.
18 SPI is widely used by microcontrollers to talk with sensors,
19 eeprom and flash memory, codecs and various other controller
20 chips, analog to digital (and d-to-a) converters, and more.
21 MMC and SD cards can be accessed using SPI protocol; and for
22 DataFlash cards used in MMC sockets, SPI must always be used.
24 SPI is one of a family of similar protocols using a four wire
25 interface (select, clock, data in, data out) including Microwire
26 (half duplex), SSP, SSI, and PSP. This driver framework should
27 work with most such devices and controllers.
32 boolean "Debug support for SPI drivers"
33 depends on DEBUG_KERNEL
35 Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
36 sysfs, and debugfs support in SPI controller and protocol drivers.
39 # MASTER side ... talking to discrete SPI slave chips including microcontrollers
43 # boolean "SPI Master Support"
47 If your system has an master-capable SPI controller (which
48 provides the clock and chipselect), you can enable that
49 controller and the protocol drivers for the SPI slave chips
54 comment "SPI Master Controller Drivers"
57 tristate "Altera SPI Controller"
60 This is the driver for the Altera SPI Controller.
63 tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
64 depends on ATH79 && GPIOLIB
67 This enables support for the SPI controller present on the
68 Atheros AR71XX/AR724X/AR913X SoCs.
71 tristate "Atmel SPI Controller"
73 depends on (ARCH_AT91 || AVR32 || COMPILE_TEST)
75 This selects a driver for the Atmel SPI Controller, present on
76 many AT32 (AVR32) and AT91 (ARM) chips.
79 tristate "BCM2835 SPI controller"
80 depends on ARCH_BCM2835 || COMPILE_TEST
82 This selects a driver for the Broadcom BCM2835 SPI master.
84 The BCM2835 contains two types of SPI master controller; the
85 "universal SPI master", and the regular SPI controller. This driver
86 is for the regular SPI controller. Slave mode operation is not also
90 tristate "SPI controller driver for ADI Blackfin5xx"
91 depends on BLACKFIN && !BF60x
93 This is the SPI controller master driver for Blackfin 5xx processor.
96 tristate "SPI controller v3 for ADI"
99 This is the SPI controller v3 master driver
100 found on Blackfin 60x processor.
102 config SPI_BFIN_SPORT
103 tristate "SPI bus via Blackfin SPORT"
106 Enable support for a SPI bus via the Blackfin SPORT peripheral.
109 tristate "Au1550/Au1200/Au1300 SPI Controller"
110 depends on MIPS_ALCHEMY
113 If you say yes to this option, support will be included for the
114 PSC SPI controller found on Au1550, Au1200 and Au1300 series.
117 tristate "Broadcom BCM53xx SPI controller"
118 depends on ARCH_BCM_5301X
119 depends on BCMA_POSSIBLE
122 Enable support for the SPI controller on Broadcom BCM53xx ARM SoCs.
125 tristate "Broadcom BCM63xx SPI controller"
128 Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
130 config SPI_BCM63XX_HSSPI
131 tristate "Broadcom BCM63XX HS SPI controller driver"
132 depends on BCM63XX || COMPILE_TEST
134 This enables support for the High Speed SPI controller present on
135 newer Broadcom BCM63XX SoCs.
138 tristate "Utilities for Bitbanging SPI masters"
140 With a few GPIO pins, your system can bitbang the SPI protocol.
141 Select this to get SPI support through I/O pins (GPIO, parallel
142 port, etc). Or, some systems' SPI master controller drivers use
143 this code to manage the per-word or per-transfer accesses to the
144 hardware shift registers.
146 This is library code, and is automatically selected by drivers that
147 need it. You only need to select this explicitly to support driver
148 modules that aren't part of this kernel tree.
151 tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
155 This uses a custom parallel port cable to connect to an AVR
156 Butterfly <http://www.atmel.com/products/avr/butterfly>, an
157 inexpensive battery powered microcontroller evaluation board.
158 This same cable can be used to flash new firmware.
161 tristate "Cadence SPI controller"
164 This selects the Cadence SPI controller master driver
168 tristate "CLPS711X host SPI controller"
169 depends on ARCH_CLPS711X || COMPILE_TEST
171 This enables dedicated general purpose SPI/Microwire1-compatible
172 master mode interface (SSI1) for CLPS711X-based CPUs.
174 config SPI_COLDFIRE_QSPI
175 tristate "Freescale Coldfire QSPI controller"
176 depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
178 This enables support for the Coldfire QSPI controller in master
182 tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
183 depends on ARCH_DAVINCI || ARCH_KEYSTONE
186 SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
189 tristate "EFM32 SPI controller"
190 depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST)
193 Driver for the spi controller found on Energy Micro's EFM32 SoCs.
196 tristate "Cirrus Logic EP93xx SPI controller"
198 depends on ARCH_EP93XX || COMPILE_TEST
200 This enables using the Cirrus EP93xx SPI controller in master
204 tristate "Falcon SPI controller support"
205 depends on SOC_FALCON
207 The external bus unit (EBU) found on the FALC-ON SoC has SPI
208 emulation that is designed for serial flash access. This driver
209 has only been tested with m25p80 type chips. The hardware has no
210 support for other types of SPI peripherals.
213 tristate "GPIO-based bitbanging SPI Master"
217 This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
218 interface to manage MOSI, MISO, SCK, and chipselect signals. SPI
219 slaves connected to a bus using this driver are configured as usual,
220 except that the spi_board_info.controller_data holds the GPIO number
221 for the chipselect used by this controller driver.
223 Note that this driver often won't achieve even 1 Mbit/sec speeds,
224 making it unusually slow for SPI. If your platform can inline
225 GPIO operations, you should be able to leverage that for better
226 speed with a custom version of this driver; see the source code.
229 tristate "Freescale i.MX SPI controllers"
230 depends on ARCH_MXC || COMPILE_TEST
233 This enables using the Freescale i.MX SPI controllers in master
237 tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
241 This driver supports the NS LM70 LLP Evaluation Board,
242 which interfaces to an LM70 temperature sensor using
246 tristate "Freescale MPC52xx SPI (non-PSC) controller support"
247 depends on PPC_MPC52xx
249 This drivers supports the MPC52xx SPI controller in master SPI
252 config SPI_MPC52xx_PSC
253 tristate "Freescale MPC52xx PSC SPI controller"
254 depends on PPC_MPC52xx
256 This enables using the Freescale MPC52xx Programmable Serial
257 Controller in master SPI mode.
259 config SPI_MPC512x_PSC
260 tristate "Freescale MPC512x PSC SPI controller"
261 depends on PPC_MPC512x
263 This enables using the Freescale MPC5121 Programmable Serial
264 Controller in SPI master mode.
275 bool "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
278 select SPI_FSL_CPM if FSL_SOC
280 This enables using the Freescale SPI controllers in master mode.
281 MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
282 MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
283 This also enables using the Aeroflex Gaisler GRLIB SPI controller in
287 tristate "Freescale DSPI controller"
290 depends on SOC_VF610 || COMPILE_TEST
292 This enables support for the Freescale DSPI controller in master
293 mode. VF610 platform uses the controller.
296 bool "Freescale eSPI controller"
300 This enables using the Freescale eSPI controllers in master mode.
301 From MPC8536, 85xx platform uses the controller, and all P10xx,
302 P20xx, P30xx,P40xx, P50xx uses this controller.
305 tristate "OpenCores tiny SPI"
309 This is the driver for OpenCores tiny SPI master controller.
312 tristate "Cavium OCTEON SPI controller"
313 depends on CAVIUM_OCTEON_SOC
315 SPI host driver for the hardware found on some Cavium OCTEON
318 config SPI_OMAP_UWIRE
319 tristate "OMAP1 MicroWire"
320 depends on ARCH_OMAP1
323 This hooks up to the MicroWire controller on OMAP1 chips.
326 tristate "McSPI driver for OMAP"
328 depends on ARM || ARM64 || AVR32 || HEXAGON || MIPS || SUPERH
329 depends on ARCH_OMAP2PLUS || COMPILE_TEST
331 SPI master controller for OMAP24XX and later Multichannel SPI
335 tristate "DRA7xxx QSPI controller support"
336 depends on ARCH_OMAP2PLUS || COMPILE_TEST
338 QSPI master controller for DRA7xxx used for flash devices.
339 This device supports single, dual and quad read support, while
340 it only supports single write mode.
343 tristate "OMAP SPI 100K"
344 depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
346 OMAP SPI 100K master controller for omap7xx boards.
349 tristate "Orion SPI master"
350 depends on PLAT_ORION || COMPILE_TEST
352 This enables using the SPI master controller on the Orion chips.
355 tristate "ARM AMBA PL022 SSP controller"
357 default y if MACH_U300
358 default y if ARCH_REALVIEW
359 default y if INTEGRATOR_IMPD1
360 default y if ARCH_VERSATILE
362 This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
363 controller. If you have an embedded system with an AMBA(R)
364 bus and a PL022 controller, say Y or M here.
367 tristate "PPC4xx SPI Controller"
368 depends on PPC32 && 4xx
371 This selects a driver for the PPC4xx SPI Controller.
373 config SPI_PXA2XX_PXADMA
374 bool "PXA2xx SSP legacy PXA DMA API support"
375 depends on SPI_PXA2XX && ARCH_PXA
377 Enable PXA private legacy DMA API support. Note that this is
378 deprecated in favor of generic DMA engine API.
380 config SPI_PXA2XX_DMA
382 depends on SPI_PXA2XX && !SPI_PXA2XX_PXADMA
385 tristate "PXA2xx SSP SPI master"
386 depends on (ARCH_PXA || PCI || ACPI)
387 select PXA_SSP if ARCH_PXA
389 This enables using a PXA2xx or Sodaville SSP port as a SPI master
390 controller. The driver can be configured to use any SSP port and
391 additional documentation can be found a Documentation/spi/pxa2xx.
393 config SPI_PXA2XX_PCI
394 def_tristate SPI_PXA2XX && PCI && COMMON_CLK
397 tristate "Rockchip SPI controller driver"
398 depends on ARM || ARM64 || AVR32 || HEXAGON || MIPS || SUPERH
400 This selects a driver for Rockchip SPI controller.
402 If you say yes to this option, support will be included for
403 RK3066, RK3188 and RK3288 families of SPI controller.
404 Rockchip SPI controller support DMA transport and PIO mode.
405 The main usecase of this controller is to use spi flash as boot
409 tristate "Renesas RSPI/QSPI controller"
410 depends on SUPERH || ARCH_SHMOBILE || COMPILE_TEST
412 SPI driver for Renesas RSPI and QSPI blocks.
415 tristate "Qualcomm SPI controller with QUP interface"
416 depends on ARCH_QCOM || (ARM && COMPILE_TEST)
418 Qualcomm Universal Peripheral (QUP) core is an AHB slave that
419 provides a common data path (an output FIFO and an input FIFO)
420 for serial peripheral interface (SPI) mini-core. SPI in master
421 mode supports up to 50MHz, up to four chip selects, programmable
422 data path from 4 bits to 32 bits and numerous protocol variants.
424 This driver can also be built as a module. If so, the module
425 will be called spi_qup.
428 tristate "Samsung S3C24XX series SPI"
429 depends on ARCH_S3C24XX
432 SPI driver for Samsung S3C24XX series ARM SoCs
434 config SPI_S3C24XX_FIQ
435 bool "S3C24XX driver with FIQ pseudo-DMA"
436 depends on SPI_S3C24XX
439 Enable FIQ support for the S3C24XX SPI driver to provide pseudo
440 DMA by using the fast-interrupt request framework, This allows
441 the driver to get DMA-like performance when there are either
442 no free DMA channels, or when doing transfers that required both
443 TX and RX data paths.
446 tristate "Samsung S3C64XX series type SPI"
447 depends on PLAT_SAMSUNG
448 select S3C64XX_PL080 if ARCH_S3C64XX
450 SPI driver for Samsung S3C64XX and newer SoCs.
453 tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
456 SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
459 tristate "SuperH MSIOF SPI controller"
460 depends on HAVE_CLK && HAS_DMA
461 depends on SUPERH || ARCH_SHMOBILE || COMPILE_TEST
463 SPI driver for SuperH and SH Mobile MSIOF blocks.
466 tristate "SuperH SPI controller"
467 depends on SUPERH || COMPILE_TEST
469 SPI driver for SuperH SPI blocks.
472 tristate "SuperH SCI SPI controller"
476 SPI driver for SuperH SCI blocks.
479 tristate "SuperH HSPI controller"
480 depends on ARCH_SHMOBILE || COMPILE_TEST
482 SPI driver for SuperH HSPI blocks.
485 tristate "CSR SiRFprimaII SPI controller"
489 SPI driver for CSR SiRFprimaII SoCs
492 tristate "Allwinner A10 SoCs SPI controller"
493 depends on ARCH_SUNXI || COMPILE_TEST
495 SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
498 tristate "Allwinner A31 SPI controller"
499 depends on ARCH_SUNXI || COMPILE_TEST
500 depends on RESET_CONTROLLER
502 This enables using the SPI controller on the Allwinner A31 SoCs.
505 tristate "Freescale MXS SPI controller"
509 SPI driver for Freescale MXS devices.
512 tristate "NVIDIA Tegra114 SPI Controller"
513 depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
514 depends on RESET_CONTROLLER && HAS_DMA
516 SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
517 is different than the older SoCs SPI controller and also register interface
518 get changed with this controller.
520 config SPI_TEGRA20_SFLASH
521 tristate "Nvidia Tegra20 Serial flash Controller"
522 depends on ARCH_TEGRA || COMPILE_TEST
523 depends on RESET_CONTROLLER
525 SPI driver for Nvidia Tegra20 Serial flash Controller interface.
526 The main usecase of this controller is to use spi flash as boot
529 config SPI_TEGRA20_SLINK
530 tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
531 depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
532 depends on RESET_CONTROLLER && HAS_DMA
534 SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
536 config SPI_TOPCLIFF_PCH
537 tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
538 depends on PCI && (X86_32 || COMPILE_TEST)
540 SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
541 used in some x86 embedded processors.
543 This driver also supports the ML7213/ML7223/ML7831, a companion chip
544 for the Atom E6xx series and compatible with the Intel EG20T PCH.
547 tristate "Toshiba TXx9 SPI controller"
548 depends on GPIOLIB && (CPU_TX49XX || COMPILE_TEST)
550 SPI driver for Toshiba TXx9 MIPS SoCs
553 tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
556 Support for the SPI-I2C bridge found on the Analog Devices
557 AD-FMCOMMS1-EBZ board.
560 tristate "Xilinx SPI controller common module"
564 This exposes the SPI controller IP from the Xilinx EDK.
566 See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
567 Product Specification document (DS464) for hardware details.
569 Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
571 config SPI_XTENSA_XTFPGA
572 tristate "Xtensa SPI controller for xtfpga"
573 depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
576 SPI driver for xtfpga SPI master controller.
578 This simple SPI master controller is built into xtfpga bitstreams
579 and is used to control daughterboard audio codec. It always transfers
580 16 bit words in SPI mode 0, automatically asserting CS on transfer
581 start and deasserting on end.
585 tristate "Nuvoton NUC900 series SPI"
586 depends on ARCH_W90X900
589 SPI driver for Nuvoton NUC900 series ARM SoCs
592 # Add new SPI master controllers in alphabetical order above this line
595 config SPI_DESIGNWARE
596 tristate "DesignWare SPI controller core support"
598 general driver for SPI controller core from DesignWare
601 tristate "PCI interface driver for DW SPI core"
602 depends on SPI_DESIGNWARE && PCI
604 config SPI_DW_MID_DMA
605 bool "DMA support for DW SPI controller on Intel MID platform"
606 depends on SPI_DW_PCI && INTEL_MID_DMAC
609 tristate "Memory-mapped io interface driver for DW SPI core"
610 depends on SPI_DESIGNWARE
613 # There are lots of SPI device types, with sensors and memory
614 # being probably the most widely used ones.
616 comment "SPI Protocol Masters"
619 tristate "User mode SPI device driver support"
621 This supports user mode SPI protocol drivers.
623 Note that this application programming interface is EXPERIMENTAL
624 and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
627 tristate "Infineon TLE62X0 (for power switching)"
630 SPI driver for Infineon TLE62X0 series line driver chips,
631 such as the TLE6220, TLE6230 and TLE6240. This provides a
632 sysfs interface, with each line presented as a kind of GPIO
633 exposing both switch control and diagnostic feedback.
636 # Add new SPI protocol masters in alphabetical order above this line
641 # (slave support would go here)