2 * comedi/drivers/s626.c
3 * Sensoray s626 Comedi driver
5 * COMEDI - Linux Control and Measurement Device Interface
6 * Copyright (C) 2000 David A. Schleef <ds@schleef.org>
8 * Based on Sensoray Model 626 Linux driver Version 0.2
9 * Copyright (C) 2002-2004 Sensoray Co., Inc.
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License as published by
13 * the Free Software Foundation; either version 2 of the License, or
14 * (at your option) any later version.
16 * This program is distributed in the hope that it will be useful,
17 * but WITHOUT ANY WARRANTY; without even the implied warranty of
18 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
19 * GNU General Public License for more details.
24 * Description: Sensoray 626 driver
25 * Devices: [Sensoray] 626 (s626)
26 * Authors: Gianluca Palli <gpalli@deis.unibo.it>,
27 * Updated: Fri, 15 Feb 2008 10:28:42 +0000
28 * Status: experimental
30 * Configuration options: not applicable, uses PCI auto config
32 * INSN_CONFIG instructions:
40 * s626 has 3 dio subdevices (2,3 and 4) each with 16 i/o channels
41 * supported configuration options:
42 * INSN_CONFIG_DIO_QUERY
47 * Every channel must be configured before reading.
51 * insn.insn=INSN_CONFIG; //configuration instruction
52 * insn.n=1; //number of operation (must be 1)
53 * insn.data=&initialvalue; //initial value loaded into encoder
54 * //during configuration
55 * insn.subdev=5; //encoder subdevice
56 * insn.chanspec=CR_PACK(encoder_channel,0,AREF_OTHER); //encoder_channel
59 * comedi_do_insn(cf,&insn); //executing configuration
62 #include <linux/module.h>
63 #include <linux/delay.h>
64 #include <linux/interrupt.h>
65 #include <linux/kernel.h>
66 #include <linux/types.h>
68 #include "../comedi_pci.h"
72 struct s626_buffer_dma {
73 dma_addr_t physical_base;
78 uint8_t ai_cmd_running; /* ai_cmd is running */
79 unsigned int ai_sample_timer; /* time between samples in
80 * units of the timer */
81 int ai_convert_count; /* conversion counter */
82 unsigned int ai_convert_timer; /* time between conversion in
83 * units of the timer */
84 uint16_t counter_int_enabs; /* counter interrupt enable mask
85 * for MISC2 register */
86 uint8_t adc_items; /* number of items in ADC poll list */
87 struct s626_buffer_dma rps_buf; /* DMA buffer used to hold ADC (RPS1)
89 struct s626_buffer_dma ana_buf; /* DMA buffer used to receive ADC data
90 * and hold DAC data */
91 uint32_t *dac_wbuf; /* pointer to logical adrs of DMA buffer
92 * used to hold DAC data */
93 uint16_t dacpol; /* image of DAC polarity register */
94 uint8_t trim_setpoint[12]; /* images of TrimDAC setpoints */
95 uint32_t i2c_adrs; /* I2C device address for onboard EEPROM
96 * (board rev dependent) */
99 /* Counter overflow/index event flag masks for RDMISC2. */
100 #define S626_INDXMASK(C) (1 << (((C) > 2) ? ((C) * 2 - 1) : ((C) * 2 + 4)))
101 #define S626_OVERMASK(C) (1 << (((C) > 2) ? ((C) * 2 + 5) : ((C) * 2 + 10)))
104 * Enable/disable a function or test status bit(s) that are accessed
105 * through Main Control Registers 1 or 2.
107 static void s626_mc_enable(struct comedi_device *dev,
108 unsigned int cmd, unsigned int reg)
110 unsigned int val = (cmd << 16) | cmd;
113 writel(val, dev->mmio + reg);
116 static void s626_mc_disable(struct comedi_device *dev,
117 unsigned int cmd, unsigned int reg)
119 writel(cmd << 16, dev->mmio + reg);
123 static bool s626_mc_test(struct comedi_device *dev,
124 unsigned int cmd, unsigned int reg)
128 val = readl(dev->mmio + reg);
130 return (val & cmd) ? true : false;
133 #define S626_BUGFIX_STREG(REGADRS) ((REGADRS) - 4)
135 /* Write a time slot control record to TSL2. */
136 #define S626_VECTPORT(VECTNUM) (S626_P_TSL2 + ((VECTNUM) << 2))
138 static const struct comedi_lrange s626_range_table = {
146 * Execute a DEBI transfer. This must be called from within a critical section.
148 static void s626_debi_transfer(struct comedi_device *dev)
150 static const int timeout = 10000;
153 /* Initiate upload of shadow RAM to DEBI control register */
154 s626_mc_enable(dev, S626_MC2_UPLD_DEBI, S626_P_MC2);
157 * Wait for completion of upload from shadow RAM to
158 * DEBI control register.
160 for (i = 0; i < timeout; i++) {
161 if (s626_mc_test(dev, S626_MC2_UPLD_DEBI, S626_P_MC2))
166 dev_err(dev->class_dev,
167 "Timeout while uploading to DEBI control register\n");
169 /* Wait until DEBI transfer is done */
170 for (i = 0; i < timeout; i++) {
171 if (!(readl(dev->mmio + S626_P_PSR) & S626_PSR_DEBI_S))
176 dev_err(dev->class_dev, "DEBI transfer timeout\n");
180 * Read a value from a gate array register.
182 static uint16_t s626_debi_read(struct comedi_device *dev, uint16_t addr)
184 /* Set up DEBI control register value in shadow RAM */
185 writel(S626_DEBI_CMD_RDWORD | addr, dev->mmio + S626_P_DEBICMD);
187 /* Execute the DEBI transfer. */
188 s626_debi_transfer(dev);
190 return readl(dev->mmio + S626_P_DEBIAD);
194 * Write a value to a gate array register.
196 static void s626_debi_write(struct comedi_device *dev, uint16_t addr,
199 /* Set up DEBI control register value in shadow RAM */
200 writel(S626_DEBI_CMD_WRWORD | addr, dev->mmio + S626_P_DEBICMD);
201 writel(wdata, dev->mmio + S626_P_DEBIAD);
203 /* Execute the DEBI transfer. */
204 s626_debi_transfer(dev);
208 * Replace the specified bits in a gate array register. Imports: mask
209 * specifies bits that are to be preserved, wdata is new value to be
210 * or'd with the masked original.
212 static void s626_debi_replace(struct comedi_device *dev, unsigned int addr,
213 unsigned int mask, unsigned int wdata)
218 writel(S626_DEBI_CMD_RDWORD | addr, dev->mmio + S626_P_DEBICMD);
219 s626_debi_transfer(dev);
221 writel(S626_DEBI_CMD_WRWORD | addr, dev->mmio + S626_P_DEBICMD);
222 val = readl(dev->mmio + S626_P_DEBIAD);
225 writel(val & 0xffff, dev->mmio + S626_P_DEBIAD);
226 s626_debi_transfer(dev);
229 /* ************** EEPROM ACCESS FUNCTIONS ************** */
231 static int s626_i2c_handshake_eoc(struct comedi_device *dev,
232 struct comedi_subdevice *s,
233 struct comedi_insn *insn,
234 unsigned long context)
238 status = s626_mc_test(dev, S626_MC2_UPLD_IIC, S626_P_MC2);
244 static int s626_i2c_handshake(struct comedi_device *dev, uint32_t val)
249 /* Write I2C command to I2C Transfer Control shadow register */
250 writel(val, dev->mmio + S626_P_I2CCTRL);
253 * Upload I2C shadow registers into working registers and
254 * wait for upload confirmation.
256 s626_mc_enable(dev, S626_MC2_UPLD_IIC, S626_P_MC2);
257 ret = comedi_timeout(dev, NULL, NULL, s626_i2c_handshake_eoc, 0);
261 /* Wait until I2C bus transfer is finished or an error occurs */
263 ctrl = readl(dev->mmio + S626_P_I2CCTRL);
264 } while ((ctrl & (S626_I2C_BUSY | S626_I2C_ERR)) == S626_I2C_BUSY);
266 /* Return non-zero if I2C error occurred */
267 return ctrl & S626_I2C_ERR;
270 /* Read uint8_t from EEPROM. */
271 static uint8_t s626_i2c_read(struct comedi_device *dev, uint8_t addr)
273 struct s626_private *devpriv = dev->private;
276 * Send EEPROM target address:
277 * Byte2 = I2C command: write to I2C EEPROM device.
278 * Byte1 = EEPROM internal target address.
281 if (s626_i2c_handshake(dev, S626_I2C_B2(S626_I2C_ATTRSTART,
283 S626_I2C_B1(S626_I2C_ATTRSTOP, addr) |
284 S626_I2C_B0(S626_I2C_ATTRNOP, 0)))
285 /* Abort function and declare error if handshake failed. */
289 * Execute EEPROM read:
290 * Byte2 = I2C command: read from I2C EEPROM device.
291 * Byte1 receives uint8_t from EEPROM.
294 if (s626_i2c_handshake(dev, S626_I2C_B2(S626_I2C_ATTRSTART,
295 (devpriv->i2c_adrs | 1)) |
296 S626_I2C_B1(S626_I2C_ATTRSTOP, 0) |
297 S626_I2C_B0(S626_I2C_ATTRNOP, 0)))
298 /* Abort function and declare error if handshake failed. */
301 return (readl(dev->mmio + S626_P_I2CCTRL) >> 16) & 0xff;
304 /* *********** DAC FUNCTIONS *********** */
306 /* TrimDac LogicalChan-to-PhysicalChan mapping table. */
307 static const uint8_t s626_trimchan[] = { 10, 9, 8, 3, 2, 7, 6, 1, 0, 5, 4 };
309 /* TrimDac LogicalChan-to-EepromAdrs mapping table. */
310 static const uint8_t s626_trimadrs[] = {
311 0x40, 0x41, 0x42, 0x50, 0x51, 0x52, 0x53, 0x60, 0x61, 0x62, 0x63
315 s626_send_dac_wait_not_mc1_a2out,
316 s626_send_dac_wait_ssr_af2_out,
317 s626_send_dac_wait_fb_buffer2_msb_00,
318 s626_send_dac_wait_fb_buffer2_msb_ff
321 static int s626_send_dac_eoc(struct comedi_device *dev,
322 struct comedi_subdevice *s,
323 struct comedi_insn *insn,
324 unsigned long context)
329 case s626_send_dac_wait_not_mc1_a2out:
330 status = readl(dev->mmio + S626_P_MC1);
331 if (!(status & S626_MC1_A2OUT))
334 case s626_send_dac_wait_ssr_af2_out:
335 status = readl(dev->mmio + S626_P_SSR);
336 if (status & S626_SSR_AF2_OUT)
339 case s626_send_dac_wait_fb_buffer2_msb_00:
340 status = readl(dev->mmio + S626_P_FB_BUFFER2);
341 if (!(status & 0xff000000))
344 case s626_send_dac_wait_fb_buffer2_msb_ff:
345 status = readl(dev->mmio + S626_P_FB_BUFFER2);
346 if (status & 0xff000000)
356 * Private helper function: Transmit serial data to DAC via Audio
357 * channel 2. Assumes: (1) TSL2 slot records initialized, and (2)
358 * dacpol contains valid target image.
360 static int s626_send_dac(struct comedi_device *dev, uint32_t val)
362 struct s626_private *devpriv = dev->private;
365 /* START THE SERIAL CLOCK RUNNING ------------- */
368 * Assert DAC polarity control and enable gating of DAC serial clock
369 * and audio bit stream signals. At this point in time we must be
370 * assured of being in time slot 0. If we are not in slot 0, the
371 * serial clock and audio stream signals will be disabled; this is
372 * because the following s626_debi_write statement (which enables
373 * signals to be passed through the gate array) would execute before
374 * the trailing edge of WS1/WS3 (which turns off the signals), thus
375 * causing the signals to be inactive during the DAC write.
377 s626_debi_write(dev, S626_LP_DACPOL, devpriv->dacpol);
379 /* TRANSFER OUTPUT DWORD VALUE INTO A2'S OUTPUT FIFO ---------------- */
381 /* Copy DAC setpoint value to DAC's output DMA buffer. */
382 /* writel(val, dev->mmio + (uint32_t)devpriv->dac_wbuf); */
383 *devpriv->dac_wbuf = val;
386 * Enable the output DMA transfer. This will cause the DMAC to copy
387 * the DAC's data value to A2's output FIFO. The DMA transfer will
388 * then immediately terminate because the protection address is
389 * reached upon transfer of the first DWORD value.
391 s626_mc_enable(dev, S626_MC1_A2OUT, S626_P_MC1);
393 /* While the DMA transfer is executing ... */
396 * Reset Audio2 output FIFO's underflow flag (along with any
397 * other FIFO underflow/overflow flags). When set, this flag
398 * will indicate that we have emerged from slot 0.
400 writel(S626_ISR_AFOU, dev->mmio + S626_P_ISR);
403 * Wait for the DMA transfer to finish so that there will be data
404 * available in the FIFO when time slot 1 tries to transfer a DWORD
405 * from the FIFO to the output buffer register. We test for DMA
406 * Done by polling the DMAC enable flag; this flag is automatically
407 * cleared when the transfer has finished.
409 ret = comedi_timeout(dev, NULL, NULL, s626_send_dac_eoc,
410 s626_send_dac_wait_not_mc1_a2out);
412 dev_err(dev->class_dev, "DMA transfer timeout\n");
416 /* START THE OUTPUT STREAM TO THE TARGET DAC -------------------- */
419 * FIFO data is now available, so we enable execution of time slots
420 * 1 and higher by clearing the EOS flag in slot 0. Note that SD3
421 * will be shifted in and stored in FB_BUFFER2 for end-of-slot-list
424 writel(S626_XSD2 | S626_RSD3 | S626_SIB_A2,
425 dev->mmio + S626_VECTPORT(0));
428 * Wait for slot 1 to execute to ensure that the Packet will be
429 * transmitted. This is detected by polling the Audio2 output FIFO
430 * underflow flag, which will be set when slot 1 execution has
431 * finished transferring the DAC's data DWORD from the output FIFO
432 * to the output buffer register.
434 ret = comedi_timeout(dev, NULL, NULL, s626_send_dac_eoc,
435 s626_send_dac_wait_ssr_af2_out);
437 dev_err(dev->class_dev,
438 "TSL timeout waiting for slot 1 to execute\n");
443 * Set up to trap execution at slot 0 when the TSL sequencer cycles
444 * back to slot 0 after executing the EOS in slot 5. Also,
445 * simultaneously shift out and in the 0x00 that is ALWAYS the value
446 * stored in the last byte to be shifted out of the FIFO's DWORD
449 writel(S626_XSD2 | S626_XFIFO_2 | S626_RSD2 | S626_SIB_A2 | S626_EOS,
450 dev->mmio + S626_VECTPORT(0));
452 /* WAIT FOR THE TRANSACTION TO FINISH ----------------------- */
455 * Wait for the TSL to finish executing all time slots before
456 * exiting this function. We must do this so that the next DAC
457 * write doesn't start, thereby enabling clock/chip select signals:
459 * 1. Before the TSL sequence cycles back to slot 0, which disables
460 * the clock/cs signal gating and traps slot // list execution.
461 * we have not yet finished slot 5 then the clock/cs signals are
462 * still gated and we have not finished transmitting the stream.
464 * 2. While slots 2-5 are executing due to a late slot 0 trap. In
465 * this case, the slot sequence is currently repeating, but with
466 * clock/cs signals disabled. We must wait for slot 0 to trap
467 * execution before setting up the next DAC setpoint DMA transfer
468 * and enabling the clock/cs signals. To detect the end of slot 5,
469 * we test for the FB_BUFFER2 MSB contents to be equal to 0xFF. If
470 * the TSL has not yet finished executing slot 5 ...
472 if (readl(dev->mmio + S626_P_FB_BUFFER2) & 0xff000000) {
474 * The trap was set on time and we are still executing somewhere
475 * in slots 2-5, so we now wait for slot 0 to execute and trap
476 * TSL execution. This is detected when FB_BUFFER2 MSB changes
477 * from 0xFF to 0x00, which slot 0 causes to happen by shifting
478 * out/in on SD2 the 0x00 that is always referenced by slot 5.
480 ret = comedi_timeout(dev, NULL, NULL, s626_send_dac_eoc,
481 s626_send_dac_wait_fb_buffer2_msb_00);
483 dev_err(dev->class_dev,
484 "TSL timeout waiting for slot 0 to execute\n");
489 * Either (1) we were too late setting the slot 0 trap; the TSL
490 * sequencer restarted slot 0 before we could set the EOS trap flag,
491 * or (2) we were not late and execution is now trapped at slot 0.
492 * In either case, we must now change slot 0 so that it will store
493 * value 0xFF (instead of 0x00) to FB_BUFFER2 next time it executes.
494 * In order to do this, we reprogram slot 0 so that it will shift in
495 * SD3, which is driven only by a pull-up resistor.
497 writel(S626_RSD3 | S626_SIB_A2 | S626_EOS,
498 dev->mmio + S626_VECTPORT(0));
501 * Wait for slot 0 to execute, at which time the TSL is setup for
502 * the next DAC write. This is detected when FB_BUFFER2 MSB changes
505 ret = comedi_timeout(dev, NULL, NULL, s626_send_dac_eoc,
506 s626_send_dac_wait_fb_buffer2_msb_ff);
508 dev_err(dev->class_dev,
509 "TSL timeout waiting for slot 0 to execute\n");
516 * Private helper function: Write setpoint to an application DAC channel.
518 static int s626_set_dac(struct comedi_device *dev,
519 uint16_t chan, int16_t dacdata)
521 struct s626_private *devpriv = dev->private;
527 * Adjust DAC data polarity and set up Polarity Control Register image.
529 signmask = 1 << chan;
532 devpriv->dacpol |= signmask;
534 devpriv->dacpol &= ~signmask;
537 /* Limit DAC setpoint value to valid range. */
538 if ((uint16_t)dacdata > 0x1FFF)
542 * Set up TSL2 records (aka "vectors") for DAC update. Vectors V2
543 * and V3 transmit the setpoint to the target DAC. V4 and V5 send
544 * data to a non-existent TrimDac channel just to keep the clock
545 * running after sending data to the target DAC. This is necessary
546 * to eliminate the clock glitch that would otherwise occur at the
547 * end of the target DAC's serial data stream. When the sequence
548 * restarts at V0 (after executing V5), the gate array automatically
549 * disables gating for the DAC clock and all DAC chip selects.
552 /* Choose DAC chip select to be asserted */
553 ws_image = (chan & 2) ? S626_WS1 : S626_WS2;
554 /* Slot 2: Transmit high data byte to target DAC */
555 writel(S626_XSD2 | S626_XFIFO_1 | ws_image,
556 dev->mmio + S626_VECTPORT(2));
557 /* Slot 3: Transmit low data byte to target DAC */
558 writel(S626_XSD2 | S626_XFIFO_0 | ws_image,
559 dev->mmio + S626_VECTPORT(3));
560 /* Slot 4: Transmit to non-existent TrimDac channel to keep clock */
561 writel(S626_XSD2 | S626_XFIFO_3 | S626_WS3,
562 dev->mmio + S626_VECTPORT(4));
563 /* Slot 5: running after writing target DAC's low data byte */
564 writel(S626_XSD2 | S626_XFIFO_2 | S626_WS3 | S626_EOS,
565 dev->mmio + S626_VECTPORT(5));
568 * Construct and transmit target DAC's serial packet:
569 * (A10D DDDD), (DDDD DDDD), (0x0F), (0x00) where A is chan<0>,
570 * and D<12:0> is the DAC setpoint. Append a WORD value (that writes
571 * to a non-existent TrimDac channel) that serves to keep the clock
572 * running after the packet has been sent to the target DAC.
574 val = 0x0F000000; /* Continue clock after target DAC data
575 * (write to non-existent trimdac). */
576 val |= 0x00004000; /* Address the two main dual-DAC devices
577 * (TSL's chip select enables target device). */
578 val |= ((uint32_t)(chan & 1) << 15); /* Address the DAC channel
579 * within the device. */
580 val |= (uint32_t)dacdata; /* Include DAC setpoint data. */
581 return s626_send_dac(dev, val);
584 static int s626_write_trim_dac(struct comedi_device *dev,
585 uint8_t logical_chan, uint8_t dac_data)
587 struct s626_private *devpriv = dev->private;
591 * Save the new setpoint in case the application needs to read it back
594 devpriv->trim_setpoint[logical_chan] = (uint8_t)dac_data;
596 /* Map logical channel number to physical channel number. */
597 chan = s626_trimchan[logical_chan];
600 * Set up TSL2 records for TrimDac write operation. All slots shift
601 * 0xFF in from pulled-up SD3 so that the end of the slot sequence
605 /* Slot 2: Send high uint8_t to target TrimDac */
606 writel(S626_XSD2 | S626_XFIFO_1 | S626_WS3,
607 dev->mmio + S626_VECTPORT(2));
608 /* Slot 3: Send low uint8_t to target TrimDac */
609 writel(S626_XSD2 | S626_XFIFO_0 | S626_WS3,
610 dev->mmio + S626_VECTPORT(3));
611 /* Slot 4: Send NOP high uint8_t to DAC0 to keep clock running */
612 writel(S626_XSD2 | S626_XFIFO_3 | S626_WS1,
613 dev->mmio + S626_VECTPORT(4));
614 /* Slot 5: Send NOP low uint8_t to DAC0 */
615 writel(S626_XSD2 | S626_XFIFO_2 | S626_WS1 | S626_EOS,
616 dev->mmio + S626_VECTPORT(5));
619 * Construct and transmit target DAC's serial packet:
620 * (0000 AAAA), (DDDD DDDD), (0x00), (0x00) where A<3:0> is the
621 * DAC channel's address, and D<7:0> is the DAC setpoint. Append a
622 * WORD value (that writes a channel 0 NOP command to a non-existent
623 * main DAC channel) that serves to keep the clock running after the
624 * packet has been sent to the target DAC.
628 * Address the DAC channel within the trimdac device.
629 * Include DAC setpoint data.
631 return s626_send_dac(dev, (chan << 8) | dac_data);
634 static int s626_load_trim_dacs(struct comedi_device *dev)
639 /* Copy TrimDac setpoint values from EEPROM to TrimDacs. */
640 for (i = 0; i < ARRAY_SIZE(s626_trimchan); i++) {
641 ret = s626_write_trim_dac(dev, i,
642 s626_i2c_read(dev, s626_trimadrs[i]));
649 /* ****** COUNTER FUNCTIONS ******* */
652 * All counter functions address a specific counter by means of the
653 * "Counter" argument, which is a logical counter number. The Counter
654 * argument may have any of the following legal values: 0=0A, 1=1A,
655 * 2=2A, 3=0B, 4=1B, 5=2B.
659 * Return/set a counter pair's latch trigger source. 0: On read
660 * access, 1: A index latches A, 2: B index latches B, 3: A overflow
663 static void s626_set_latch_source(struct comedi_device *dev,
664 unsigned int chan, uint16_t value)
666 s626_debi_replace(dev, S626_LP_CRB(chan),
667 ~(S626_CRBMSK_INTCTRL | S626_CRBMSK_LATCHSRC),
668 S626_SET_CRB_LATCHSRC(value));
672 * Write value into counter preload register.
674 static void s626_preload(struct comedi_device *dev,
675 unsigned int chan, uint32_t value)
677 s626_debi_write(dev, S626_LP_CNTR(chan), value);
678 s626_debi_write(dev, S626_LP_CNTR(chan) + 2, value >> 16);
681 /* ****** PRIVATE COUNTER FUNCTIONS ****** */
684 * Reset a counter's index and overflow event capture flags.
686 static void s626_reset_cap_flags(struct comedi_device *dev,
691 set = S626_SET_CRB_INTRESETCMD(1);
693 set |= S626_SET_CRB_INTRESET_A(1);
695 set |= S626_SET_CRB_INTRESET_B(1);
697 s626_debi_replace(dev, S626_LP_CRB(chan), ~S626_CRBMSK_INTCTRL, set);
702 * Return counter setup in a format (COUNTER_SETUP) that is consistent
703 * for both A and B counters.
705 static uint16_t s626_get_mode_a(struct comedi_device *dev,
711 unsigned cntsrc, clkmult, clkpol, encmode;
713 /* Fetch CRA and CRB register images. */
714 cra = s626_debi_read(dev, S626_LP_CRA(chan));
715 crb = s626_debi_read(dev, S626_LP_CRB(chan));
718 * Populate the standardized counter setup bit fields.
721 /* LoadSrc = LoadSrcA. */
722 S626_SET_STD_LOADSRC(S626_GET_CRA_LOADSRC_A(cra)) |
723 /* LatchSrc = LatchSrcA. */
724 S626_SET_STD_LATCHSRC(S626_GET_CRB_LATCHSRC(crb)) |
725 /* IntSrc = IntSrcA. */
726 S626_SET_STD_INTSRC(S626_GET_CRA_INTSRC_A(cra)) |
727 /* IndxSrc = IndxSrcA. */
728 S626_SET_STD_INDXSRC(S626_GET_CRA_INDXSRC_A(cra)) |
729 /* IndxPol = IndxPolA. */
730 S626_SET_STD_INDXPOL(S626_GET_CRA_INDXPOL_A(cra)) |
731 /* ClkEnab = ClkEnabA. */
732 S626_SET_STD_CLKENAB(S626_GET_CRB_CLKENAB_A(crb));
734 /* Adjust mode-dependent parameters. */
735 cntsrc = S626_GET_CRA_CNTSRC_A(cra);
736 if (cntsrc & S626_CNTSRC_SYSCLK) {
737 /* Timer mode (CntSrcA<1> == 1): */
738 encmode = S626_ENCMODE_TIMER;
739 /* Set ClkPol to indicate count direction (CntSrcA<0>). */
741 /* ClkMult must be 1x in Timer mode. */
742 clkmult = S626_CLKMULT_1X;
744 /* Counter mode (CntSrcA<1> == 0): */
745 encmode = S626_ENCMODE_COUNTER;
746 /* Pass through ClkPol. */
747 clkpol = S626_GET_CRA_CLKPOL_A(cra);
748 /* Force ClkMult to 1x if not legal, else pass through. */
749 clkmult = S626_GET_CRA_CLKMULT_A(cra);
750 if (clkmult == S626_CLKMULT_SPECIAL)
751 clkmult = S626_CLKMULT_1X;
753 setup |= S626_SET_STD_ENCMODE(encmode) | S626_SET_STD_CLKMULT(clkmult) |
754 S626_SET_STD_CLKPOL(clkpol);
756 /* Return adjusted counter setup. */
760 static uint16_t s626_get_mode_b(struct comedi_device *dev,
766 unsigned cntsrc, clkmult, clkpol, encmode;
768 /* Fetch CRA and CRB register images. */
769 cra = s626_debi_read(dev, S626_LP_CRA(chan));
770 crb = s626_debi_read(dev, S626_LP_CRB(chan));
773 * Populate the standardized counter setup bit fields.
776 /* IntSrc = IntSrcB. */
777 S626_SET_STD_INTSRC(S626_GET_CRB_INTSRC_B(crb)) |
778 /* LatchSrc = LatchSrcB. */
779 S626_SET_STD_LATCHSRC(S626_GET_CRB_LATCHSRC(crb)) |
780 /* LoadSrc = LoadSrcB. */
781 S626_SET_STD_LOADSRC(S626_GET_CRB_LOADSRC_B(crb)) |
782 /* IndxPol = IndxPolB. */
783 S626_SET_STD_INDXPOL(S626_GET_CRB_INDXPOL_B(crb)) |
784 /* ClkEnab = ClkEnabB. */
785 S626_SET_STD_CLKENAB(S626_GET_CRB_CLKENAB_B(crb)) |
786 /* IndxSrc = IndxSrcB. */
787 S626_SET_STD_INDXSRC(S626_GET_CRA_INDXSRC_B(cra));
789 /* Adjust mode-dependent parameters. */
790 cntsrc = S626_GET_CRA_CNTSRC_B(cra);
791 clkmult = S626_GET_CRB_CLKMULT_B(crb);
792 if (clkmult == S626_CLKMULT_SPECIAL) {
793 /* Extender mode (ClkMultB == S626_CLKMULT_SPECIAL): */
794 encmode = S626_ENCMODE_EXTENDER;
795 /* Indicate multiplier is 1x. */
796 clkmult = S626_CLKMULT_1X;
797 /* Set ClkPol equal to Timer count direction (CntSrcB<0>). */
799 } else if (cntsrc & S626_CNTSRC_SYSCLK) {
800 /* Timer mode (CntSrcB<1> == 1): */
801 encmode = S626_ENCMODE_TIMER;
802 /* Indicate multiplier is 1x. */
803 clkmult = S626_CLKMULT_1X;
804 /* Set ClkPol equal to Timer count direction (CntSrcB<0>). */
807 /* If Counter mode (CntSrcB<1> == 0): */
808 encmode = S626_ENCMODE_COUNTER;
809 /* Clock multiplier is passed through. */
810 /* Clock polarity is passed through. */
811 clkpol = S626_GET_CRB_CLKPOL_B(crb);
813 setup |= S626_SET_STD_ENCMODE(encmode) | S626_SET_STD_CLKMULT(clkmult) |
814 S626_SET_STD_CLKPOL(clkpol);
816 /* Return adjusted counter setup. */
820 static uint16_t s626_get_mode(struct comedi_device *dev,
823 return (chan < 3) ? s626_get_mode_a(dev, chan)
824 : s626_get_mode_b(dev, chan);
829 * Set the operating mode for the specified counter. The setup
830 * parameter is treated as a COUNTER_SETUP data type. The following
831 * parameters are programmable (all other parms are ignored): ClkMult,
832 * ClkPol, ClkEnab, IndexSrc, IndexPol, LoadSrc.
834 static void s626_set_mode_a(struct comedi_device *dev,
835 unsigned int chan, uint16_t setup,
836 uint16_t disable_int_src)
838 struct s626_private *devpriv = dev->private;
841 unsigned cntsrc, clkmult, clkpol;
843 /* Initialize CRA and CRB images. */
844 /* Preload trigger is passed through. */
845 cra = S626_SET_CRA_LOADSRC_A(S626_GET_STD_LOADSRC(setup));
846 /* IndexSrc is passed through. */
847 cra |= S626_SET_CRA_INDXSRC_A(S626_GET_STD_INDXSRC(setup));
849 /* Reset any pending CounterA event captures. */
850 crb = S626_SET_CRB_INTRESETCMD(1) | S626_SET_CRB_INTRESET_A(1);
851 /* Clock enable is passed through. */
852 crb |= S626_SET_CRB_CLKENAB_A(S626_GET_STD_CLKENAB(setup));
854 /* Force IntSrc to Disabled if disable_int_src is asserted. */
855 if (!disable_int_src)
856 cra |= S626_SET_CRA_INTSRC_A(S626_GET_STD_INTSRC(setup));
858 /* Populate all mode-dependent attributes of CRA & CRB images. */
859 clkpol = S626_GET_STD_CLKPOL(setup);
860 switch (S626_GET_STD_ENCMODE(setup)) {
861 case S626_ENCMODE_EXTENDER: /* Extender Mode: */
862 /* Force to Timer mode (Extender valid only for B counters). */
863 /* Fall through to case S626_ENCMODE_TIMER: */
864 case S626_ENCMODE_TIMER: /* Timer Mode: */
865 /* CntSrcA<1> selects system clock */
866 cntsrc = S626_CNTSRC_SYSCLK;
867 /* Count direction (CntSrcA<0>) obtained from ClkPol. */
869 /* ClkPolA behaves as always-on clock enable. */
871 /* ClkMult must be 1x. */
872 clkmult = S626_CLKMULT_1X;
874 default: /* Counter Mode: */
875 /* Select ENC_C and ENC_D as clock/direction inputs. */
876 cntsrc = S626_CNTSRC_ENCODER;
877 /* Clock polarity is passed through. */
878 /* Force multiplier to x1 if not legal, else pass through. */
879 clkmult = S626_GET_STD_CLKMULT(setup);
880 if (clkmult == S626_CLKMULT_SPECIAL)
881 clkmult = S626_CLKMULT_1X;
884 cra |= S626_SET_CRA_CNTSRC_A(cntsrc) | S626_SET_CRA_CLKPOL_A(clkpol) |
885 S626_SET_CRA_CLKMULT_A(clkmult);
888 * Force positive index polarity if IndxSrc is software-driven only,
889 * otherwise pass it through.
891 if (S626_GET_STD_INDXSRC(setup) != S626_INDXSRC_SOFT)
892 cra |= S626_SET_CRA_INDXPOL_A(S626_GET_STD_INDXPOL(setup));
895 * If IntSrc has been forced to Disabled, update the MISC2 interrupt
896 * enable mask to indicate the counter interrupt is disabled.
899 devpriv->counter_int_enabs &= ~(S626_OVERMASK(chan) |
900 S626_INDXMASK(chan));
903 * While retaining CounterB and LatchSrc configurations, program the
904 * new counter operating mode.
906 s626_debi_replace(dev, S626_LP_CRA(chan),
907 S626_CRAMSK_INDXSRC_B | S626_CRAMSK_CNTSRC_B, cra);
908 s626_debi_replace(dev, S626_LP_CRB(chan),
909 ~(S626_CRBMSK_INTCTRL | S626_CRBMSK_CLKENAB_A), crb);
912 static void s626_set_mode_b(struct comedi_device *dev,
913 unsigned int chan, uint16_t setup,
914 uint16_t disable_int_src)
916 struct s626_private *devpriv = dev->private;
919 unsigned cntsrc, clkmult, clkpol;
921 /* Initialize CRA and CRB images. */
922 /* IndexSrc is passed through. */
923 cra = S626_SET_CRA_INDXSRC_B(S626_GET_STD_INDXSRC(setup));
925 /* Reset event captures and disable interrupts. */
926 crb = S626_SET_CRB_INTRESETCMD(1) | S626_SET_CRB_INTRESET_B(1);
927 /* Clock enable is passed through. */
928 crb |= S626_SET_CRB_CLKENAB_B(S626_GET_STD_CLKENAB(setup));
929 /* Preload trigger source is passed through. */
930 crb |= S626_SET_CRB_LOADSRC_B(S626_GET_STD_LOADSRC(setup));
932 /* Force IntSrc to Disabled if disable_int_src is asserted. */
933 if (!disable_int_src)
934 crb |= S626_SET_CRB_INTSRC_B(S626_GET_STD_INTSRC(setup));
936 /* Populate all mode-dependent attributes of CRA & CRB images. */
937 clkpol = S626_GET_STD_CLKPOL(setup);
938 switch (S626_GET_STD_ENCMODE(setup)) {
939 case S626_ENCMODE_TIMER: /* Timer Mode: */
940 /* CntSrcB<1> selects system clock */
941 cntsrc = S626_CNTSRC_SYSCLK;
942 /* with direction (CntSrcB<0>) obtained from ClkPol. */
944 /* ClkPolB behaves as always-on clock enable. */
946 /* ClkMultB must be 1x. */
947 clkmult = S626_CLKMULT_1X;
949 case S626_ENCMODE_EXTENDER: /* Extender Mode: */
950 /* CntSrcB source is OverflowA (same as "timer") */
951 cntsrc = S626_CNTSRC_SYSCLK;
952 /* with direction obtained from ClkPol. */
954 /* ClkPolB controls IndexB -- always set to active. */
956 /* ClkMultB selects OverflowA as the clock source. */
957 clkmult = S626_CLKMULT_SPECIAL;
959 default: /* Counter Mode: */
960 /* Select ENC_C and ENC_D as clock/direction inputs. */
961 cntsrc = S626_CNTSRC_ENCODER;
962 /* ClkPol is passed through. */
963 /* Force ClkMult to x1 if not legal, otherwise pass through. */
964 clkmult = S626_GET_STD_CLKMULT(setup);
965 if (clkmult == S626_CLKMULT_SPECIAL)
966 clkmult = S626_CLKMULT_1X;
969 cra |= S626_SET_CRA_CNTSRC_B(cntsrc);
970 crb |= S626_SET_CRB_CLKPOL_B(clkpol) | S626_SET_CRB_CLKMULT_B(clkmult);
973 * Force positive index polarity if IndxSrc is software-driven only,
974 * otherwise pass it through.
976 if (S626_GET_STD_INDXSRC(setup) != S626_INDXSRC_SOFT)
977 crb |= S626_SET_CRB_INDXPOL_B(S626_GET_STD_INDXPOL(setup));
980 * If IntSrc has been forced to Disabled, update the MISC2 interrupt
981 * enable mask to indicate the counter interrupt is disabled.
984 devpriv->counter_int_enabs &= ~(S626_OVERMASK(chan) |
985 S626_INDXMASK(chan));
988 * While retaining CounterA and LatchSrc configurations, program the
989 * new counter operating mode.
991 s626_debi_replace(dev, S626_LP_CRA(chan),
992 ~(S626_CRAMSK_INDXSRC_B | S626_CRAMSK_CNTSRC_B), cra);
993 s626_debi_replace(dev, S626_LP_CRB(chan),
994 S626_CRBMSK_CLKENAB_A | S626_CRBMSK_LATCHSRC, crb);
997 static void s626_set_mode(struct comedi_device *dev,
999 uint16_t setup, uint16_t disable_int_src)
1002 s626_set_mode_a(dev, chan, setup, disable_int_src);
1004 s626_set_mode_b(dev, chan, setup, disable_int_src);
1008 * Return/set a counter's enable. enab: 0=always enabled, 1=enabled by index.
1010 static void s626_set_enable(struct comedi_device *dev,
1011 unsigned int chan, uint16_t enab)
1013 unsigned int mask = S626_CRBMSK_INTCTRL;
1017 mask |= S626_CRBMSK_CLKENAB_A;
1018 set = S626_SET_CRB_CLKENAB_A(enab);
1020 mask |= S626_CRBMSK_CLKENAB_B;
1021 set = S626_SET_CRB_CLKENAB_B(enab);
1023 s626_debi_replace(dev, S626_LP_CRB(chan), ~mask, set);
1027 static uint16_t s626_get_enable(struct comedi_device *dev,
1030 uint16_t crb = s626_debi_read(dev, S626_LP_CRB(chan));
1032 return (chan < 3) ? S626_GET_CRB_CLKENAB_A(crb)
1033 : S626_GET_CRB_CLKENAB_B(crb);
1038 static uint16_t s626_get_latch_source(struct comedi_device *dev,
1041 return S626_GET_CRB_LATCHSRC(s626_debi_read(dev, S626_LP_CRB(chan)));
1046 * Return/set the event that will trigger transfer of the preload
1047 * register into the counter. 0=ThisCntr_Index, 1=ThisCntr_Overflow,
1048 * 2=OverflowA (B counters only), 3=disabled.
1050 static void s626_set_load_trig(struct comedi_device *dev,
1051 unsigned int chan, uint16_t trig)
1058 reg = S626_LP_CRA(chan);
1059 mask = S626_CRAMSK_LOADSRC_A;
1060 set = S626_SET_CRA_LOADSRC_A(trig);
1062 reg = S626_LP_CRB(chan);
1063 mask = S626_CRBMSK_LOADSRC_B | S626_CRBMSK_INTCTRL;
1064 set = S626_SET_CRB_LOADSRC_B(trig);
1066 s626_debi_replace(dev, reg, ~mask, set);
1070 static uint16_t s626_get_load_trig(struct comedi_device *dev,
1074 return S626_GET_CRA_LOADSRC_A(s626_debi_read(dev,
1075 S626_LP_CRA(chan)));
1077 return S626_GET_CRB_LOADSRC_B(s626_debi_read(dev,
1078 S626_LP_CRB(chan)));
1083 * Return/set counter interrupt source and clear any captured
1084 * index/overflow events. int_source: 0=Disabled, 1=OverflowOnly,
1085 * 2=IndexOnly, 3=IndexAndOverflow.
1087 static void s626_set_int_src(struct comedi_device *dev,
1088 unsigned int chan, uint16_t int_source)
1090 struct s626_private *devpriv = dev->private;
1091 uint16_t cra_reg = S626_LP_CRA(chan);
1092 uint16_t crb_reg = S626_LP_CRB(chan);
1095 /* Reset any pending counter overflow or index captures */
1096 s626_debi_replace(dev, crb_reg, ~S626_CRBMSK_INTCTRL,
1097 S626_SET_CRB_INTRESETCMD(1) |
1098 S626_SET_CRB_INTRESET_A(1));
1100 /* Program counter interrupt source */
1101 s626_debi_replace(dev, cra_reg, ~S626_CRAMSK_INTSRC_A,
1102 S626_SET_CRA_INTSRC_A(int_source));
1106 /* Cache writeable CRB register image */
1107 crb = s626_debi_read(dev, crb_reg);
1108 crb &= ~S626_CRBMSK_INTCTRL;
1110 /* Reset any pending counter overflow or index captures */
1111 s626_debi_write(dev, crb_reg,
1112 crb | S626_SET_CRB_INTRESETCMD(1) |
1113 S626_SET_CRB_INTRESET_B(1));
1115 /* Program counter interrupt source */
1116 s626_debi_write(dev, crb_reg,
1117 (crb & ~S626_CRBMSK_INTSRC_B) |
1118 S626_SET_CRB_INTSRC_B(int_source));
1121 /* Update MISC2 interrupt enable mask. */
1122 devpriv->counter_int_enabs &= ~(S626_OVERMASK(chan) |
1123 S626_INDXMASK(chan));
1124 switch (int_source) {
1129 devpriv->counter_int_enabs |= S626_OVERMASK(chan);
1132 devpriv->counter_int_enabs |= S626_INDXMASK(chan);
1135 devpriv->counter_int_enabs |= (S626_OVERMASK(chan) |
1136 S626_INDXMASK(chan));
1142 static uint16_t s626_get_int_src(struct comedi_device *dev,
1146 return S626_GET_CRA_INTSRC_A(s626_debi_read(dev,
1147 S626_LP_CRA(chan)));
1149 return S626_GET_CRB_INTSRC_B(s626_debi_read(dev,
1150 S626_LP_CRB(chan)));
1156 * Return/set the clock multiplier.
1158 static void s626_set_clk_mult(struct comedi_device *dev,
1159 unsigned int chan, uint16_t value)
1163 mode = s626_get_mode(dev, chan);
1164 mode &= ~S626_STDMSK_CLKMULT;
1165 mode |= S626_SET_STD_CLKMULT(value);
1167 s626_set_mode(dev, chan, mode, false);
1170 static uint16_t s626_get_clk_mult(struct comedi_device *dev,
1173 return S626_GET_STD_CLKMULT(s626_get_mode(dev, chan));
1177 * Return/set the clock polarity.
1179 static void s626_set_clk_pol(struct comedi_device *dev,
1180 unsigned int chan, uint16_t value)
1184 mode = s626_get_mode(dev, chan);
1185 mode &= ~S626_STDMSK_CLKPOL;
1186 mode |= S626_SET_STD_CLKPOL(value);
1188 s626_set_mode(dev, chan, mode, false);
1191 static uint16_t s626_get_clk_pol(struct comedi_device *dev,
1194 return S626_GET_STD_CLKPOL(s626_get_mode(dev, chan));
1198 * Return/set the encoder mode.
1200 static void s626_set_enc_mode(struct comedi_device *dev,
1201 unsigned int chan, uint16_t value)
1205 mode = s626_get_mode(dev, chan);
1206 mode &= ~S626_STDMSK_ENCMODE;
1207 mode |= S626_SET_STD_ENCMODE(value);
1209 s626_set_mode(dev, chan, mode, false);
1212 static uint16_t s626_get_enc_mode(struct comedi_device *dev,
1215 return S626_GET_STD_ENCMODE(s626_get_mode(dev, chan));
1219 * Return/set the index polarity.
1221 static void s626_set_index_pol(struct comedi_device *dev,
1222 unsigned int chan, uint16_t value)
1226 mode = s626_get_mode(dev, chan);
1227 mode &= ~S626_STDMSK_INDXPOL;
1228 mode |= S626_SET_STD_INDXPOL(value != 0);
1230 s626_set_mode(dev, chan, mode, false);
1233 static uint16_t s626_get_index_pol(struct comedi_device *dev,
1236 return S626_GET_STD_INDXPOL(s626_get_mode(dev, chan));
1240 * Return/set the index source.
1242 static void s626_set_index_src(struct comedi_device *dev,
1243 unsigned int chan, uint16_t value)
1247 mode = s626_get_mode(dev, chan);
1248 mode &= ~S626_STDMSK_INDXSRC;
1249 mode |= S626_SET_STD_INDXSRC(value != 0);
1251 s626_set_mode(dev, chan, mode, false);
1254 static uint16_t s626_get_index_src(struct comedi_device *dev,
1257 return S626_GET_STD_INDXSRC(s626_get_mode(dev, chan));
1262 * Generate an index pulse.
1264 static void s626_pulse_index(struct comedi_device *dev,
1270 cra = s626_debi_read(dev, S626_LP_CRA(chan));
1273 s626_debi_write(dev, S626_LP_CRA(chan),
1274 (cra ^ S626_CRAMSK_INDXPOL_A));
1275 s626_debi_write(dev, S626_LP_CRA(chan), cra);
1279 crb = s626_debi_read(dev, S626_LP_CRB(chan));
1280 crb &= ~S626_CRBMSK_INTCTRL;
1283 s626_debi_write(dev, S626_LP_CRB(chan),
1284 (crb ^ S626_CRBMSK_INDXPOL_B));
1285 s626_debi_write(dev, S626_LP_CRB(chan), crb);
1289 static unsigned int s626_ai_reg_to_uint(unsigned int data)
1291 return ((data >> 18) & 0x3fff) ^ 0x2000;
1294 static int s626_dio_set_irq(struct comedi_device *dev, unsigned int chan)
1296 unsigned int group = chan / 16;
1297 unsigned int mask = 1 << (chan - (16 * group));
1298 unsigned int status;
1300 /* set channel to capture positive edge */
1301 status = s626_debi_read(dev, S626_LP_RDEDGSEL(group));
1302 s626_debi_write(dev, S626_LP_WREDGSEL(group), mask | status);
1304 /* enable interrupt on selected channel */
1305 status = s626_debi_read(dev, S626_LP_RDINTSEL(group));
1306 s626_debi_write(dev, S626_LP_WRINTSEL(group), mask | status);
1308 /* enable edge capture write command */
1309 s626_debi_write(dev, S626_LP_MISC1, S626_MISC1_EDCAP);
1311 /* enable edge capture on selected channel */
1312 status = s626_debi_read(dev, S626_LP_RDCAPSEL(group));
1313 s626_debi_write(dev, S626_LP_WRCAPSEL(group), mask | status);
1318 static int s626_dio_reset_irq(struct comedi_device *dev, unsigned int group,
1321 /* disable edge capture write command */
1322 s626_debi_write(dev, S626_LP_MISC1, S626_MISC1_NOEDCAP);
1324 /* enable edge capture on selected channel */
1325 s626_debi_write(dev, S626_LP_WRCAPSEL(group), mask);
1330 static int s626_dio_clear_irq(struct comedi_device *dev)
1334 /* disable edge capture write command */
1335 s626_debi_write(dev, S626_LP_MISC1, S626_MISC1_NOEDCAP);
1337 /* clear all dio pending events and interrupt */
1338 for (group = 0; group < S626_DIO_BANKS; group++)
1339 s626_debi_write(dev, S626_LP_WRCAPSEL(group), 0xffff);
1344 static void s626_handle_dio_interrupt(struct comedi_device *dev,
1345 uint16_t irqbit, uint8_t group)
1347 struct s626_private *devpriv = dev->private;
1348 struct comedi_subdevice *s = dev->read_subdev;
1349 struct comedi_cmd *cmd = &s->async->cmd;
1351 s626_dio_reset_irq(dev, group, irqbit);
1353 if (devpriv->ai_cmd_running) {
1354 /* check if interrupt is an ai acquisition start trigger */
1355 if ((irqbit >> (cmd->start_arg - (16 * group))) == 1 &&
1356 cmd->start_src == TRIG_EXT) {
1357 /* Start executing the RPS program */
1358 s626_mc_enable(dev, S626_MC1_ERPS1, S626_P_MC1);
1360 if (cmd->scan_begin_src == TRIG_EXT)
1361 s626_dio_set_irq(dev, cmd->scan_begin_arg);
1363 if ((irqbit >> (cmd->scan_begin_arg - (16 * group))) == 1 &&
1364 cmd->scan_begin_src == TRIG_EXT) {
1365 /* Trigger ADC scan loop start */
1366 s626_mc_enable(dev, S626_MC2_ADC_RPS, S626_P_MC2);
1368 if (cmd->convert_src == TRIG_EXT) {
1369 devpriv->ai_convert_count = cmd->chanlist_len;
1371 s626_dio_set_irq(dev, cmd->convert_arg);
1374 if (cmd->convert_src == TRIG_TIMER) {
1375 devpriv->ai_convert_count = cmd->chanlist_len;
1376 s626_set_enable(dev, 5, S626_CLKENAB_ALWAYS);
1379 if ((irqbit >> (cmd->convert_arg - (16 * group))) == 1 &&
1380 cmd->convert_src == TRIG_EXT) {
1381 /* Trigger ADC scan loop start */
1382 s626_mc_enable(dev, S626_MC2_ADC_RPS, S626_P_MC2);
1384 devpriv->ai_convert_count--;
1385 if (devpriv->ai_convert_count > 0)
1386 s626_dio_set_irq(dev, cmd->convert_arg);
1391 static void s626_check_dio_interrupts(struct comedi_device *dev)
1396 for (group = 0; group < S626_DIO_BANKS; group++) {
1397 /* read interrupt type */
1398 irqbit = s626_debi_read(dev, S626_LP_RDCAPFLG(group));
1400 /* check if interrupt is generated from dio channels */
1402 s626_handle_dio_interrupt(dev, irqbit, group);
1408 static void s626_check_counter_interrupts(struct comedi_device *dev)
1410 struct s626_private *devpriv = dev->private;
1411 struct comedi_subdevice *s = dev->read_subdev;
1412 struct comedi_async *async = s->async;
1413 struct comedi_cmd *cmd = &async->cmd;
1416 /* read interrupt type */
1417 irqbit = s626_debi_read(dev, S626_LP_RDMISC2);
1419 /* check interrupt on counters */
1420 if (irqbit & S626_IRQ_COINT1A) {
1421 /* clear interrupt capture flag */
1422 s626_reset_cap_flags(dev, 0);
1424 if (irqbit & S626_IRQ_COINT2A) {
1425 /* clear interrupt capture flag */
1426 s626_reset_cap_flags(dev, 1);
1428 if (irqbit & S626_IRQ_COINT3A) {
1429 /* clear interrupt capture flag */
1430 s626_reset_cap_flags(dev, 2);
1432 if (irqbit & S626_IRQ_COINT1B) {
1433 /* clear interrupt capture flag */
1434 s626_reset_cap_flags(dev, 3);
1436 if (irqbit & S626_IRQ_COINT2B) {
1437 /* clear interrupt capture flag */
1438 s626_reset_cap_flags(dev, 4);
1440 if (devpriv->ai_convert_count > 0) {
1441 devpriv->ai_convert_count--;
1442 if (devpriv->ai_convert_count == 0)
1443 s626_set_enable(dev, 4, S626_CLKENAB_INDEX);
1445 if (cmd->convert_src == TRIG_TIMER) {
1446 /* Trigger ADC scan loop start */
1447 s626_mc_enable(dev, S626_MC2_ADC_RPS,
1452 if (irqbit & S626_IRQ_COINT3B) {
1453 /* clear interrupt capture flag */
1454 s626_reset_cap_flags(dev, 5);
1456 if (cmd->scan_begin_src == TRIG_TIMER) {
1457 /* Trigger ADC scan loop start */
1458 s626_mc_enable(dev, S626_MC2_ADC_RPS, S626_P_MC2);
1461 if (cmd->convert_src == TRIG_TIMER) {
1462 devpriv->ai_convert_count = cmd->chanlist_len;
1463 s626_set_enable(dev, 4, S626_CLKENAB_ALWAYS);
1468 static bool s626_handle_eos_interrupt(struct comedi_device *dev)
1470 struct s626_private *devpriv = dev->private;
1471 struct comedi_subdevice *s = dev->read_subdev;
1472 struct comedi_async *async = s->async;
1473 struct comedi_cmd *cmd = &async->cmd;
1475 * Init ptr to DMA buffer that holds new ADC data. We skip the
1476 * first uint16_t in the buffer because it contains junk data
1477 * from the final ADC of the previous poll list scan.
1479 uint32_t *readaddr = (uint32_t *)devpriv->ana_buf.logical_base + 1;
1482 /* get the data and hand it over to comedi */
1483 for (i = 0; i < cmd->chanlist_len; i++) {
1484 unsigned short tempdata;
1487 * Convert ADC data to 16-bit integer values and copy
1488 * to application buffer.
1490 tempdata = s626_ai_reg_to_uint(*readaddr);
1493 comedi_buf_write_samples(s, &tempdata, 1);
1496 if (cmd->stop_src == TRIG_COUNT && async->scans_done >= cmd->stop_arg)
1497 async->events |= COMEDI_CB_EOA;
1499 if (async->events & COMEDI_CB_CANCEL_MASK)
1500 devpriv->ai_cmd_running = 0;
1502 if (devpriv->ai_cmd_running && cmd->scan_begin_src == TRIG_EXT)
1503 s626_dio_set_irq(dev, cmd->scan_begin_arg);
1505 comedi_handle_events(dev, s);
1507 return !devpriv->ai_cmd_running;
1510 static irqreturn_t s626_irq_handler(int irq, void *d)
1512 struct comedi_device *dev = d;
1513 unsigned long flags;
1514 uint32_t irqtype, irqstatus;
1518 /* lock to avoid race with comedi_poll */
1519 spin_lock_irqsave(&dev->spinlock, flags);
1521 /* save interrupt enable register state */
1522 irqstatus = readl(dev->mmio + S626_P_IER);
1524 /* read interrupt type */
1525 irqtype = readl(dev->mmio + S626_P_ISR);
1527 /* disable master interrupt */
1528 writel(0, dev->mmio + S626_P_IER);
1530 /* clear interrupt */
1531 writel(irqtype, dev->mmio + S626_P_ISR);
1534 case S626_IRQ_RPS1: /* end_of_scan occurs */
1535 if (s626_handle_eos_interrupt(dev))
1538 case S626_IRQ_GPIO3: /* check dio and counter interrupt */
1539 /* s626_dio_clear_irq(dev); */
1540 s626_check_dio_interrupts(dev);
1541 s626_check_counter_interrupts(dev);
1545 /* enable interrupt */
1546 writel(irqstatus, dev->mmio + S626_P_IER);
1548 spin_unlock_irqrestore(&dev->spinlock, flags);
1553 * This function builds the RPS program for hardware driven acquisition.
1555 static void s626_reset_adc(struct comedi_device *dev, uint8_t *ppl)
1557 struct s626_private *devpriv = dev->private;
1558 struct comedi_subdevice *s = dev->read_subdev;
1559 struct comedi_cmd *cmd = &s->async->cmd;
1566 /* Stop RPS program in case it is currently running */
1567 s626_mc_disable(dev, S626_MC1_ERPS1, S626_P_MC1);
1569 /* Set starting logical address to write RPS commands. */
1570 rps = (uint32_t *)devpriv->rps_buf.logical_base;
1572 /* Initialize RPS instruction pointer */
1573 writel((uint32_t)devpriv->rps_buf.physical_base,
1574 dev->mmio + S626_P_RPSADDR1);
1576 /* Construct RPS program in rps_buf DMA buffer */
1577 if (cmd->scan_begin_src != TRIG_FOLLOW) {
1578 /* Wait for Start trigger. */
1579 *rps++ = S626_RPS_PAUSE | S626_RPS_SIGADC;
1580 *rps++ = S626_RPS_CLRSIGNAL | S626_RPS_SIGADC;
1584 * SAA7146 BUG WORKAROUND Do a dummy DEBI Write. This is necessary
1585 * because the first RPS DEBI Write following a non-RPS DEBI write
1586 * seems to always fail. If we don't do this dummy write, the ADC
1587 * gain might not be set to the value required for the first slot in
1588 * the poll list; the ADC gain would instead remain unchanged from
1589 * the previously programmed value.
1591 /* Write DEBI Write command and address to shadow RAM. */
1592 *rps++ = S626_RPS_LDREG | (S626_P_DEBICMD >> 2);
1593 *rps++ = S626_DEBI_CMD_WRWORD | S626_LP_GSEL;
1594 *rps++ = S626_RPS_LDREG | (S626_P_DEBIAD >> 2);
1595 /* Write DEBI immediate data to shadow RAM: */
1596 *rps++ = S626_GSEL_BIPOLAR5V; /* arbitrary immediate data value. */
1597 *rps++ = S626_RPS_CLRSIGNAL | S626_RPS_DEBI;
1598 /* Reset "shadow RAM uploaded" flag. */
1599 /* Invoke shadow RAM upload. */
1600 *rps++ = S626_RPS_UPLOAD | S626_RPS_DEBI;
1601 /* Wait for shadow upload to finish. */
1602 *rps++ = S626_RPS_PAUSE | S626_RPS_DEBI;
1605 * Digitize all slots in the poll list. This is implemented as a
1606 * for loop to limit the slot count to 16 in case the application
1607 * forgot to set the S626_EOPL flag in the final slot.
1609 for (devpriv->adc_items = 0; devpriv->adc_items < 16;
1610 devpriv->adc_items++) {
1612 * Convert application's poll list item to private board class
1613 * format. Each app poll list item is an uint8_t with form
1614 * (EOPL,x,x,RANGE,CHAN<3:0>), where RANGE code indicates 0 =
1615 * +-10V, 1 = +-5V, and EOPL = End of Poll List marker.
1617 local_ppl = (*ppl << 8) | (*ppl & 0x10 ? S626_GSEL_BIPOLAR5V :
1618 S626_GSEL_BIPOLAR10V);
1620 /* Switch ADC analog gain. */
1621 /* Write DEBI command and address to shadow RAM. */
1622 *rps++ = S626_RPS_LDREG | (S626_P_DEBICMD >> 2);
1623 *rps++ = S626_DEBI_CMD_WRWORD | S626_LP_GSEL;
1624 /* Write DEBI immediate data to shadow RAM. */
1625 *rps++ = S626_RPS_LDREG | (S626_P_DEBIAD >> 2);
1627 /* Reset "shadow RAM uploaded" flag. */
1628 *rps++ = S626_RPS_CLRSIGNAL | S626_RPS_DEBI;
1629 /* Invoke shadow RAM upload. */
1630 *rps++ = S626_RPS_UPLOAD | S626_RPS_DEBI;
1631 /* Wait for shadow upload to finish. */
1632 *rps++ = S626_RPS_PAUSE | S626_RPS_DEBI;
1633 /* Select ADC analog input channel. */
1634 *rps++ = S626_RPS_LDREG | (S626_P_DEBICMD >> 2);
1635 /* Write DEBI command and address to shadow RAM. */
1636 *rps++ = S626_DEBI_CMD_WRWORD | S626_LP_ISEL;
1637 *rps++ = S626_RPS_LDREG | (S626_P_DEBIAD >> 2);
1638 /* Write DEBI immediate data to shadow RAM. */
1640 /* Reset "shadow RAM uploaded" flag. */
1641 *rps++ = S626_RPS_CLRSIGNAL | S626_RPS_DEBI;
1642 /* Invoke shadow RAM upload. */
1643 *rps++ = S626_RPS_UPLOAD | S626_RPS_DEBI;
1644 /* Wait for shadow upload to finish. */
1645 *rps++ = S626_RPS_PAUSE | S626_RPS_DEBI;
1648 * Delay at least 10 microseconds for analog input settling.
1649 * Instead of padding with NOPs, we use S626_RPS_JUMP
1650 * instructions here; this allows us to produce a longer delay
1651 * than is possible with NOPs because each S626_RPS_JUMP
1652 * flushes the RPS' instruction prefetch pipeline.
1655 (uint32_t)devpriv->rps_buf.physical_base +
1656 (uint32_t)((unsigned long)rps -
1657 (unsigned long)devpriv->
1658 rps_buf.logical_base);
1659 for (i = 0; i < (10 * S626_RPSCLK_PER_US / 2); i++) {
1660 jmp_adrs += 8; /* Repeat to implement time delay: */
1661 /* Jump to next RPS instruction. */
1662 *rps++ = S626_RPS_JUMP;
1666 if (cmd->convert_src != TRIG_NOW) {
1667 /* Wait for Start trigger. */
1668 *rps++ = S626_RPS_PAUSE | S626_RPS_SIGADC;
1669 *rps++ = S626_RPS_CLRSIGNAL | S626_RPS_SIGADC;
1671 /* Start ADC by pulsing GPIO1. */
1672 /* Begin ADC Start pulse. */
1673 *rps++ = S626_RPS_LDREG | (S626_P_GPIO >> 2);
1674 *rps++ = S626_GPIO_BASE | S626_GPIO1_LO;
1675 *rps++ = S626_RPS_NOP;
1676 /* VERSION 2.03 CHANGE: STRETCH OUT ADC START PULSE. */
1677 /* End ADC Start pulse. */
1678 *rps++ = S626_RPS_LDREG | (S626_P_GPIO >> 2);
1679 *rps++ = S626_GPIO_BASE | S626_GPIO1_HI;
1681 * Wait for ADC to complete (GPIO2 is asserted high when ADC not
1682 * busy) and for data from previous conversion to shift into FB
1683 * BUFFER 1 register.
1685 /* Wait for ADC done. */
1686 *rps++ = S626_RPS_PAUSE | S626_RPS_GPIO2;
1688 /* Transfer ADC data from FB BUFFER 1 register to DMA buffer. */
1689 *rps++ = S626_RPS_STREG |
1690 (S626_BUGFIX_STREG(S626_P_FB_BUFFER1) >> 2);
1691 *rps++ = (uint32_t)devpriv->ana_buf.physical_base +
1692 (devpriv->adc_items << 2);
1695 * If this slot's EndOfPollList flag is set, all channels have
1696 * now been processed.
1698 if (*ppl++ & S626_EOPL) {
1699 devpriv->adc_items++; /* Adjust poll list item count. */
1700 break; /* Exit poll list processing loop. */
1705 * VERSION 2.01 CHANGE: DELAY CHANGED FROM 250NS to 2US. Allow the
1706 * ADC to stabilize for 2 microseconds before starting the final
1707 * (dummy) conversion. This delay is necessary to allow sufficient
1708 * time between last conversion finished and the start of the dummy
1709 * conversion. Without this delay, the last conversion's data value
1710 * is sometimes set to the previous conversion's data value.
1712 for (n = 0; n < (2 * S626_RPSCLK_PER_US); n++)
1713 *rps++ = S626_RPS_NOP;
1716 * Start a dummy conversion to cause the data from the last
1717 * conversion of interest to be shifted in.
1719 /* Begin ADC Start pulse. */
1720 *rps++ = S626_RPS_LDREG | (S626_P_GPIO >> 2);
1721 *rps++ = S626_GPIO_BASE | S626_GPIO1_LO;
1722 *rps++ = S626_RPS_NOP;
1723 /* VERSION 2.03 CHANGE: STRETCH OUT ADC START PULSE. */
1724 *rps++ = S626_RPS_LDREG | (S626_P_GPIO >> 2); /* End ADC Start pulse. */
1725 *rps++ = S626_GPIO_BASE | S626_GPIO1_HI;
1728 * Wait for the data from the last conversion of interest to arrive
1729 * in FB BUFFER 1 register.
1731 *rps++ = S626_RPS_PAUSE | S626_RPS_GPIO2; /* Wait for ADC done. */
1733 /* Transfer final ADC data from FB BUFFER 1 register to DMA buffer. */
1734 *rps++ = S626_RPS_STREG | (S626_BUGFIX_STREG(S626_P_FB_BUFFER1) >> 2);
1735 *rps++ = (uint32_t)devpriv->ana_buf.physical_base +
1736 (devpriv->adc_items << 2);
1738 /* Indicate ADC scan loop is finished. */
1739 /* Signal ReadADC() that scan is done. */
1740 /* *rps++= S626_RPS_CLRSIGNAL | S626_RPS_SIGADC; */
1742 /* invoke interrupt */
1743 if (devpriv->ai_cmd_running == 1)
1744 *rps++ = S626_RPS_IRQ;
1746 /* Restart RPS program at its beginning. */
1747 *rps++ = S626_RPS_JUMP; /* Branch to start of RPS program. */
1748 *rps++ = (uint32_t)devpriv->rps_buf.physical_base;
1750 /* End of RPS program build */
1754 static int s626_ai_rinsn(struct comedi_device *dev,
1755 struct comedi_subdevice *s,
1756 struct comedi_insn *insn,
1759 struct s626_private *devpriv = dev->private;
1763 /* Trigger ADC scan loop start */
1764 s626_mc_enable(dev, S626_MC2_ADC_RPS, S626_P_MC2);
1766 /* Wait until ADC scan loop is finished (RPS Signal 0 reset) */
1767 while (s626_mc_test(dev, S626_MC2_ADC_RPS, S626_P_MC2))
1771 * Init ptr to DMA buffer that holds new ADC data. We skip the
1772 * first uint16_t in the buffer because it contains junk data from
1773 * the final ADC of the previous poll list scan.
1775 readaddr = (uint32_t *)devpriv->ana_buf.logical_base + 1;
1778 * Convert ADC data to 16-bit integer values and
1779 * copy to application buffer.
1781 for (i = 0; i < devpriv->adc_items; i++) {
1782 *data = s626_ai_reg_to_uint(*readaddr++);
1790 static int s626_ai_eoc(struct comedi_device *dev,
1791 struct comedi_subdevice *s,
1792 struct comedi_insn *insn,
1793 unsigned long context)
1795 unsigned int status;
1797 status = readl(dev->mmio + S626_P_PSR);
1798 if (status & S626_PSR_GPIO2)
1803 static int s626_ai_insn_read(struct comedi_device *dev,
1804 struct comedi_subdevice *s,
1805 struct comedi_insn *insn,
1808 uint16_t chan = CR_CHAN(insn->chanspec);
1809 uint16_t range = CR_RANGE(insn->chanspec);
1810 uint16_t adc_spec = 0;
1811 uint32_t gpio_image;
1817 * Convert application's ADC specification into form
1818 * appropriate for register programming.
1821 adc_spec = (chan << 8) | (S626_GSEL_BIPOLAR5V);
1823 adc_spec = (chan << 8) | (S626_GSEL_BIPOLAR10V);
1825 /* Switch ADC analog gain. */
1826 s626_debi_write(dev, S626_LP_GSEL, adc_spec); /* Set gain. */
1828 /* Select ADC analog input channel. */
1829 s626_debi_write(dev, S626_LP_ISEL, adc_spec); /* Select channel. */
1831 for (n = 0; n < insn->n; n++) {
1832 /* Delay 10 microseconds for analog input settling. */
1835 /* Start ADC by pulsing GPIO1 low */
1836 gpio_image = readl(dev->mmio + S626_P_GPIO);
1837 /* Assert ADC Start command */
1838 writel(gpio_image & ~S626_GPIO1_HI, dev->mmio + S626_P_GPIO);
1839 /* and stretch it out */
1840 writel(gpio_image & ~S626_GPIO1_HI, dev->mmio + S626_P_GPIO);
1841 writel(gpio_image & ~S626_GPIO1_HI, dev->mmio + S626_P_GPIO);
1842 /* Negate ADC Start command */
1843 writel(gpio_image | S626_GPIO1_HI, dev->mmio + S626_P_GPIO);
1846 * Wait for ADC to complete (GPIO2 is asserted high when
1847 * ADC not busy) and for data from previous conversion to
1848 * shift into FB BUFFER 1 register.
1851 /* Wait for ADC done */
1852 ret = comedi_timeout(dev, s, insn, s626_ai_eoc, 0);
1856 /* Fetch ADC data */
1858 tmp = readl(dev->mmio + S626_P_FB_BUFFER1);
1859 data[n - 1] = s626_ai_reg_to_uint(tmp);
1863 * Allow the ADC to stabilize for 4 microseconds before
1864 * starting the next (final) conversion. This delay is
1865 * necessary to allow sufficient time between last
1866 * conversion finished and the start of the next
1867 * conversion. Without this delay, the last conversion's
1868 * data value is sometimes set to the previous
1869 * conversion's data value.
1875 * Start a dummy conversion to cause the data from the
1876 * previous conversion to be shifted in.
1878 gpio_image = readl(dev->mmio + S626_P_GPIO);
1879 /* Assert ADC Start command */
1880 writel(gpio_image & ~S626_GPIO1_HI, dev->mmio + S626_P_GPIO);
1881 /* and stretch it out */
1882 writel(gpio_image & ~S626_GPIO1_HI, dev->mmio + S626_P_GPIO);
1883 writel(gpio_image & ~S626_GPIO1_HI, dev->mmio + S626_P_GPIO);
1884 /* Negate ADC Start command */
1885 writel(gpio_image | S626_GPIO1_HI, dev->mmio + S626_P_GPIO);
1887 /* Wait for the data to arrive in FB BUFFER 1 register. */
1889 /* Wait for ADC done */
1890 ret = comedi_timeout(dev, s, insn, s626_ai_eoc, 0);
1894 /* Fetch ADC data from audio interface's input shift register. */
1896 /* Fetch ADC data */
1898 tmp = readl(dev->mmio + S626_P_FB_BUFFER1);
1899 data[n - 1] = s626_ai_reg_to_uint(tmp);
1905 static int s626_ai_load_polllist(uint8_t *ppl, struct comedi_cmd *cmd)
1909 for (n = 0; n < cmd->chanlist_len; n++) {
1910 if (CR_RANGE(cmd->chanlist[n]) == 0)
1911 ppl[n] = CR_CHAN(cmd->chanlist[n]) | S626_RANGE_5V;
1913 ppl[n] = CR_CHAN(cmd->chanlist[n]) | S626_RANGE_10V;
1916 ppl[n - 1] |= S626_EOPL;
1921 static int s626_ai_inttrig(struct comedi_device *dev,
1922 struct comedi_subdevice *s,
1923 unsigned int trig_num)
1925 struct comedi_cmd *cmd = &s->async->cmd;
1927 if (trig_num != cmd->start_arg)
1930 /* Start executing the RPS program */
1931 s626_mc_enable(dev, S626_MC1_ERPS1, S626_P_MC1);
1933 s->async->inttrig = NULL;
1939 * This function doesn't require a particular form, this is just what
1940 * happens to be used in some of the drivers. It should convert ns
1941 * nanoseconds to a counter value suitable for programming the device.
1942 * Also, it should adjust ns so that it cooresponds to the actual time
1943 * that the device will use.
1945 static int s626_ns_to_timer(unsigned int *nanosec, unsigned int flags)
1949 base = 500; /* 2MHz internal clock */
1951 switch (flags & CMDF_ROUND_MASK) {
1952 case CMDF_ROUND_NEAREST:
1954 divider = DIV_ROUND_CLOSEST(*nanosec, base);
1956 case CMDF_ROUND_DOWN:
1957 divider = (*nanosec) / base;
1960 divider = DIV_ROUND_UP(*nanosec, base);
1964 *nanosec = base * divider;
1968 static void s626_timer_load(struct comedi_device *dev,
1969 unsigned int chan, int tick)
1972 /* Preload upon index. */
1973 S626_SET_STD_LOADSRC(S626_LOADSRC_INDX) |
1974 /* Disable hardware index. */
1975 S626_SET_STD_INDXSRC(S626_INDXSRC_SOFT) |
1976 /* Operating mode is Timer. */
1977 S626_SET_STD_ENCMODE(S626_ENCMODE_TIMER) |
1978 /* Count direction is Down. */
1979 S626_SET_STD_CLKPOL(S626_CNTDIR_DOWN) |
1980 /* Clock multiplier is 1x. */
1981 S626_SET_STD_CLKMULT(S626_CLKMULT_1X) |
1982 /* Enabled by index */
1983 S626_SET_STD_CLKENAB(S626_CLKENAB_INDEX);
1984 uint16_t value_latchsrc = S626_LATCHSRC_A_INDXA;
1985 /* uint16_t enab = S626_CLKENAB_ALWAYS; */
1987 s626_set_mode(dev, chan, setup, false);
1989 /* Set the preload register */
1990 s626_preload(dev, chan, tick);
1993 * Software index pulse forces the preload register to load
1996 s626_set_load_trig(dev, chan, 0);
1997 s626_pulse_index(dev, chan);
1999 /* set reload on counter overflow */
2000 s626_set_load_trig(dev, chan, 1);
2002 /* set interrupt on overflow */
2003 s626_set_int_src(dev, chan, S626_INTSRC_OVER);
2005 s626_set_latch_source(dev, chan, value_latchsrc);
2006 /* s626_set_enable(dev, chan, (uint16_t)(enab != 0)); */
2010 static int s626_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
2012 struct s626_private *devpriv = dev->private;
2014 struct comedi_cmd *cmd = &s->async->cmd;
2017 if (devpriv->ai_cmd_running) {
2018 dev_err(dev->class_dev,
2019 "s626_ai_cmd: Another ai_cmd is running\n");
2022 /* disable interrupt */
2023 writel(0, dev->mmio + S626_P_IER);
2025 /* clear interrupt request */
2026 writel(S626_IRQ_RPS1 | S626_IRQ_GPIO3, dev->mmio + S626_P_ISR);
2028 /* clear any pending interrupt */
2029 s626_dio_clear_irq(dev);
2030 /* s626_enc_clear_irq(dev); */
2032 /* reset ai_cmd_running flag */
2033 devpriv->ai_cmd_running = 0;
2035 s626_ai_load_polllist(ppl, cmd);
2036 devpriv->ai_cmd_running = 1;
2037 devpriv->ai_convert_count = 0;
2039 switch (cmd->scan_begin_src) {
2044 * set a counter to generate adc trigger at scan_begin_arg
2047 tick = s626_ns_to_timer(&cmd->scan_begin_arg, cmd->flags);
2049 /* load timer value and enable interrupt */
2050 s626_timer_load(dev, 5, tick);
2051 s626_set_enable(dev, 5, S626_CLKENAB_ALWAYS);
2054 /* set the digital line and interrupt for scan trigger */
2055 if (cmd->start_src != TRIG_EXT)
2056 s626_dio_set_irq(dev, cmd->scan_begin_arg);
2060 switch (cmd->convert_src) {
2065 * set a counter to generate adc trigger at convert_arg
2068 tick = s626_ns_to_timer(&cmd->convert_arg, cmd->flags);
2070 /* load timer value and enable interrupt */
2071 s626_timer_load(dev, 4, tick);
2072 s626_set_enable(dev, 4, S626_CLKENAB_INDEX);
2075 /* set the digital line and interrupt for convert trigger */
2076 if (cmd->scan_begin_src != TRIG_EXT &&
2077 cmd->start_src == TRIG_EXT)
2078 s626_dio_set_irq(dev, cmd->convert_arg);
2082 s626_reset_adc(dev, ppl);
2084 switch (cmd->start_src) {
2086 /* Trigger ADC scan loop start */
2087 /* s626_mc_enable(dev, S626_MC2_ADC_RPS, S626_P_MC2); */
2089 /* Start executing the RPS program */
2090 s626_mc_enable(dev, S626_MC1_ERPS1, S626_P_MC1);
2091 s->async->inttrig = NULL;
2094 /* configure DIO channel for acquisition trigger */
2095 s626_dio_set_irq(dev, cmd->start_arg);
2096 s->async->inttrig = NULL;
2099 s->async->inttrig = s626_ai_inttrig;
2103 /* enable interrupt */
2104 writel(S626_IRQ_GPIO3 | S626_IRQ_RPS1, dev->mmio + S626_P_IER);
2109 static int s626_ai_cmdtest(struct comedi_device *dev,
2110 struct comedi_subdevice *s, struct comedi_cmd *cmd)
2115 /* Step 1 : check if triggers are trivially valid */
2117 err |= comedi_check_trigger_src(&cmd->start_src,
2118 TRIG_NOW | TRIG_INT | TRIG_EXT);
2119 err |= comedi_check_trigger_src(&cmd->scan_begin_src,
2120 TRIG_TIMER | TRIG_EXT | TRIG_FOLLOW);
2121 err |= comedi_check_trigger_src(&cmd->convert_src,
2122 TRIG_TIMER | TRIG_EXT | TRIG_NOW);
2123 err |= comedi_check_trigger_src(&cmd->scan_end_src, TRIG_COUNT);
2124 err |= comedi_check_trigger_src(&cmd->stop_src, TRIG_COUNT | TRIG_NONE);
2129 /* Step 2a : make sure trigger sources are unique */
2131 err |= comedi_check_trigger_is_unique(cmd->start_src);
2132 err |= comedi_check_trigger_is_unique(cmd->scan_begin_src);
2133 err |= comedi_check_trigger_is_unique(cmd->convert_src);
2134 err |= comedi_check_trigger_is_unique(cmd->stop_src);
2136 /* Step 2b : and mutually compatible */
2141 /* Step 3: check if arguments are trivially valid */
2143 switch (cmd->start_src) {
2146 err |= comedi_check_trigger_arg_is(&cmd->start_arg, 0);
2149 err |= comedi_check_trigger_arg_max(&cmd->start_arg, 39);
2153 if (cmd->scan_begin_src == TRIG_EXT)
2154 err |= comedi_check_trigger_arg_max(&cmd->scan_begin_arg, 39);
2155 if (cmd->convert_src == TRIG_EXT)
2156 err |= comedi_check_trigger_arg_max(&cmd->convert_arg, 39);
2158 #define S626_MAX_SPEED 200000 /* in nanoseconds */
2159 #define S626_MIN_SPEED 2000000000 /* in nanoseconds */
2161 if (cmd->scan_begin_src == TRIG_TIMER) {
2162 err |= comedi_check_trigger_arg_min(&cmd->scan_begin_arg,
2164 err |= comedi_check_trigger_arg_max(&cmd->scan_begin_arg,
2169 * should be level/edge, hi/lo specification here
2170 * should specify multiple external triggers
2171 * err |= comedi_check_trigger_arg_max(&cmd->scan_begin_arg, 9);
2174 if (cmd->convert_src == TRIG_TIMER) {
2175 err |= comedi_check_trigger_arg_min(&cmd->convert_arg,
2177 err |= comedi_check_trigger_arg_max(&cmd->convert_arg,
2181 * external trigger - see above
2182 * err |= comedi_check_trigger_arg_max(&cmd->scan_begin_arg, 9);
2186 err |= comedi_check_trigger_arg_is(&cmd->scan_end_arg,
2189 if (cmd->stop_src == TRIG_COUNT)
2190 err |= comedi_check_trigger_arg_min(&cmd->stop_arg, 1);
2191 else /* TRIG_NONE */
2192 err |= comedi_check_trigger_arg_is(&cmd->stop_arg, 0);
2197 /* step 4: fix up any arguments */
2199 if (cmd->scan_begin_src == TRIG_TIMER) {
2200 arg = cmd->scan_begin_arg;
2201 s626_ns_to_timer(&arg, cmd->flags);
2202 err |= comedi_check_trigger_arg_is(&cmd->scan_begin_arg, arg);
2205 if (cmd->convert_src == TRIG_TIMER) {
2206 arg = cmd->convert_arg;
2207 s626_ns_to_timer(&arg, cmd->flags);
2208 err |= comedi_check_trigger_arg_is(&cmd->convert_arg, arg);
2210 if (cmd->scan_begin_src == TRIG_TIMER) {
2211 arg = cmd->convert_arg * cmd->scan_end_arg;
2212 err |= comedi_check_trigger_arg_min(&cmd->
2224 static int s626_ai_cancel(struct comedi_device *dev, struct comedi_subdevice *s)
2226 struct s626_private *devpriv = dev->private;
2228 /* Stop RPS program in case it is currently running */
2229 s626_mc_disable(dev, S626_MC1_ERPS1, S626_P_MC1);
2231 /* disable master interrupt */
2232 writel(0, dev->mmio + S626_P_IER);
2234 devpriv->ai_cmd_running = 0;
2239 static int s626_ao_insn_write(struct comedi_device *dev,
2240 struct comedi_subdevice *s,
2241 struct comedi_insn *insn,
2244 unsigned int chan = CR_CHAN(insn->chanspec);
2247 for (i = 0; i < insn->n; i++) {
2248 int16_t dacdata = (int16_t)data[i];
2251 dacdata -= (0x1fff);
2253 ret = s626_set_dac(dev, chan, dacdata);
2257 s->readback[chan] = data[i];
2263 /* *************** DIGITAL I/O FUNCTIONS *************** */
2266 * All DIO functions address a group of DIO channels by means of
2267 * "group" argument. group may be 0, 1 or 2, which correspond to DIO
2268 * ports A, B and C, respectively.
2271 static void s626_dio_init(struct comedi_device *dev)
2275 /* Prepare to treat writes to WRCapSel as capture disables. */
2276 s626_debi_write(dev, S626_LP_MISC1, S626_MISC1_NOEDCAP);
2278 /* For each group of sixteen channels ... */
2279 for (group = 0; group < S626_DIO_BANKS; group++) {
2280 /* Disable all interrupts */
2281 s626_debi_write(dev, S626_LP_WRINTSEL(group), 0);
2282 /* Disable all event captures */
2283 s626_debi_write(dev, S626_LP_WRCAPSEL(group), 0xffff);
2284 /* Init all DIOs to default edge polarity */
2285 s626_debi_write(dev, S626_LP_WREDGSEL(group), 0);
2286 /* Program all outputs to inactive state */
2287 s626_debi_write(dev, S626_LP_WRDOUT(group), 0);
2291 static int s626_dio_insn_bits(struct comedi_device *dev,
2292 struct comedi_subdevice *s,
2293 struct comedi_insn *insn,
2296 unsigned long group = (unsigned long)s->private;
2298 if (comedi_dio_update_state(s, data))
2299 s626_debi_write(dev, S626_LP_WRDOUT(group), s->state);
2301 data[1] = s626_debi_read(dev, S626_LP_RDDIN(group));
2306 static int s626_dio_insn_config(struct comedi_device *dev,
2307 struct comedi_subdevice *s,
2308 struct comedi_insn *insn,
2311 unsigned long group = (unsigned long)s->private;
2314 ret = comedi_dio_insn_config(dev, s, insn, data, 0);
2318 s626_debi_write(dev, S626_LP_WRDOUT(group), s->io_bits);
2324 * Now this function initializes the value of the counter (data[0])
2325 * and set the subdevice. To complete with trigger and interrupt
2328 * FIXME: data[0] is supposed to be an INSN_CONFIG_xxx constant indicating
2329 * what is being configured, but this function appears to be using data[0]
2332 static int s626_enc_insn_config(struct comedi_device *dev,
2333 struct comedi_subdevice *s,
2334 struct comedi_insn *insn, unsigned int *data)
2336 unsigned int chan = CR_CHAN(insn->chanspec);
2338 /* Preload upon index. */
2339 S626_SET_STD_LOADSRC(S626_LOADSRC_INDX) |
2340 /* Disable hardware index. */
2341 S626_SET_STD_INDXSRC(S626_INDXSRC_SOFT) |
2342 /* Operating mode is Counter. */
2343 S626_SET_STD_ENCMODE(S626_ENCMODE_COUNTER) |
2344 /* Active high clock. */
2345 S626_SET_STD_CLKPOL(S626_CLKPOL_POS) |
2346 /* Clock multiplier is 1x. */
2347 S626_SET_STD_CLKMULT(S626_CLKMULT_1X) |
2348 /* Enabled by index */
2349 S626_SET_STD_CLKENAB(S626_CLKENAB_INDEX);
2350 /* uint16_t disable_int_src = true; */
2351 /* uint32_t Preloadvalue; //Counter initial value */
2352 uint16_t value_latchsrc = S626_LATCHSRC_AB_READ;
2353 uint16_t enab = S626_CLKENAB_ALWAYS;
2355 /* (data==NULL) ? (Preloadvalue=0) : (Preloadvalue=data[0]); */
2357 s626_set_mode(dev, chan, setup, true);
2358 s626_preload(dev, chan, data[0]);
2359 s626_pulse_index(dev, chan);
2360 s626_set_latch_source(dev, chan, value_latchsrc);
2361 s626_set_enable(dev, chan, (enab != 0));
2366 static int s626_enc_insn_read(struct comedi_device *dev,
2367 struct comedi_subdevice *s,
2368 struct comedi_insn *insn,
2371 unsigned int chan = CR_CHAN(insn->chanspec);
2372 uint16_t cntr_latch_reg = S626_LP_CNTR(chan);
2375 for (i = 0; i < insn->n; i++) {
2379 * Read the counter's output latch LSW/MSW.
2380 * Latches on LSW read.
2382 val = s626_debi_read(dev, cntr_latch_reg);
2383 val |= (s626_debi_read(dev, cntr_latch_reg + 2) << 16);
2390 static int s626_enc_insn_write(struct comedi_device *dev,
2391 struct comedi_subdevice *s,
2392 struct comedi_insn *insn, unsigned int *data)
2394 unsigned int chan = CR_CHAN(insn->chanspec);
2396 /* Set the preload register */
2397 s626_preload(dev, chan, data[0]);
2400 * Software index pulse forces the preload register to load
2403 s626_set_load_trig(dev, chan, 0);
2404 s626_pulse_index(dev, chan);
2405 s626_set_load_trig(dev, chan, 2);
2410 static void s626_write_misc2(struct comedi_device *dev, uint16_t new_image)
2412 s626_debi_write(dev, S626_LP_MISC1, S626_MISC1_WENABLE);
2413 s626_debi_write(dev, S626_LP_WRMISC2, new_image);
2414 s626_debi_write(dev, S626_LP_MISC1, S626_MISC1_WDISABLE);
2417 static void s626_counters_init(struct comedi_device *dev)
2421 /* Preload upon index. */
2422 S626_SET_STD_LOADSRC(S626_LOADSRC_INDX) |
2423 /* Disable hardware index. */
2424 S626_SET_STD_INDXSRC(S626_INDXSRC_SOFT) |
2425 /* Operating mode is counter. */
2426 S626_SET_STD_ENCMODE(S626_ENCMODE_COUNTER) |
2427 /* Active high clock. */
2428 S626_SET_STD_CLKPOL(S626_CLKPOL_POS) |
2429 /* Clock multiplier is 1x. */
2430 S626_SET_STD_CLKMULT(S626_CLKMULT_1X) |
2431 /* Enabled by index */
2432 S626_SET_STD_CLKENAB(S626_CLKENAB_INDEX);
2435 * Disable all counter interrupts and clear any captured counter events.
2437 for (chan = 0; chan < S626_ENCODER_CHANNELS; chan++) {
2438 s626_set_mode(dev, chan, setup, true);
2439 s626_set_int_src(dev, chan, 0);
2440 s626_reset_cap_flags(dev, chan);
2441 s626_set_enable(dev, chan, S626_CLKENAB_ALWAYS);
2445 static int s626_allocate_dma_buffers(struct comedi_device *dev)
2447 struct pci_dev *pcidev = comedi_to_pci_dev(dev);
2448 struct s626_private *devpriv = dev->private;
2452 addr = pci_alloc_consistent(pcidev, S626_DMABUF_SIZE, &appdma);
2455 devpriv->ana_buf.logical_base = addr;
2456 devpriv->ana_buf.physical_base = appdma;
2458 addr = pci_alloc_consistent(pcidev, S626_DMABUF_SIZE, &appdma);
2461 devpriv->rps_buf.logical_base = addr;
2462 devpriv->rps_buf.physical_base = appdma;
2467 static void s626_free_dma_buffers(struct comedi_device *dev)
2469 struct pci_dev *pcidev = comedi_to_pci_dev(dev);
2470 struct s626_private *devpriv = dev->private;
2475 if (devpriv->rps_buf.logical_base)
2476 pci_free_consistent(pcidev, S626_DMABUF_SIZE,
2477 devpriv->rps_buf.logical_base,
2478 devpriv->rps_buf.physical_base);
2479 if (devpriv->ana_buf.logical_base)
2480 pci_free_consistent(pcidev, S626_DMABUF_SIZE,
2481 devpriv->ana_buf.logical_base,
2482 devpriv->ana_buf.physical_base);
2485 static int s626_initialize(struct comedi_device *dev)
2487 struct s626_private *devpriv = dev->private;
2488 dma_addr_t phys_buf;
2493 /* Enable DEBI and audio pins, enable I2C interface */
2494 s626_mc_enable(dev, S626_MC1_DEBI | S626_MC1_AUDIO | S626_MC1_I2C,
2498 * Configure DEBI operating mode
2500 * Local bus is 16 bits wide
2501 * Declare DEBI transfer timeout interval
2502 * Set up byte lane steering
2503 * Intel-compatible local bus (DEBI never times out)
2505 writel(S626_DEBI_CFG_SLAVE16 |
2506 (S626_DEBI_TOUT << S626_DEBI_CFG_TOUT_BIT) | S626_DEBI_SWAP |
2507 S626_DEBI_CFG_INTEL, dev->mmio + S626_P_DEBICFG);
2509 /* Disable MMU paging */
2510 writel(S626_DEBI_PAGE_DISABLE, dev->mmio + S626_P_DEBIPAGE);
2512 /* Init GPIO so that ADC Start* is negated */
2513 writel(S626_GPIO_BASE | S626_GPIO1_HI, dev->mmio + S626_P_GPIO);
2515 /* I2C device address for onboard eeprom (revb) */
2516 devpriv->i2c_adrs = 0xA0;
2519 * Issue an I2C ABORT command to halt any I2C
2520 * operation in progress and reset BUSY flag.
2522 writel(S626_I2C_CLKSEL | S626_I2C_ABORT,
2523 dev->mmio + S626_P_I2CSTAT);
2524 s626_mc_enable(dev, S626_MC2_UPLD_IIC, S626_P_MC2);
2525 ret = comedi_timeout(dev, NULL, NULL, s626_i2c_handshake_eoc, 0);
2530 * Per SAA7146 data sheet, write to STATUS
2531 * reg twice to reset all I2C error flags.
2533 for (i = 0; i < 2; i++) {
2534 writel(S626_I2C_CLKSEL, dev->mmio + S626_P_I2CSTAT);
2535 s626_mc_enable(dev, S626_MC2_UPLD_IIC, S626_P_MC2);
2536 ret = comedi_timeout(dev, NULL, NULL, s626_i2c_handshake_eoc, 0);
2542 * Init audio interface functional attributes: set DAC/ADC
2543 * serial clock rates, invert DAC serial clock so that
2544 * DAC data setup times are satisfied, enable DAC serial
2547 writel(S626_ACON2_INIT, dev->mmio + S626_P_ACON2);
2550 * Set up TSL1 slot list, which is used to control the
2551 * accumulation of ADC data: S626_RSD1 = shift data in on SD1.
2552 * S626_SIB_A1 = store data uint8_t at next available location
2553 * in FB BUFFER1 register.
2555 writel(S626_RSD1 | S626_SIB_A1, dev->mmio + S626_P_TSL1);
2556 writel(S626_RSD1 | S626_SIB_A1 | S626_EOS,
2557 dev->mmio + S626_P_TSL1 + 4);
2559 /* Enable TSL1 slot list so that it executes all the time */
2560 writel(S626_ACON1_ADCSTART, dev->mmio + S626_P_ACON1);
2563 * Initialize RPS registers used for ADC
2566 /* Physical start of RPS program */
2567 writel((uint32_t)devpriv->rps_buf.physical_base,
2568 dev->mmio + S626_P_RPSADDR1);
2569 /* RPS program performs no explicit mem writes */
2570 writel(0, dev->mmio + S626_P_RPSPAGE1);
2571 /* Disable RPS timeouts */
2572 writel(0, dev->mmio + S626_P_RPS1_TOUT);
2576 * SAA7146 BUG WORKAROUND
2578 * Initialize SAA7146 ADC interface to a known state by
2579 * invoking ADCs until FB BUFFER 1 register shows that it
2580 * is correctly receiving ADC data. This is necessary
2581 * because the SAA7146 ADC interface does not start up in
2582 * a defined state after a PCI reset.
2585 struct comedi_subdevice *s = dev->read_subdev;
2590 unsigned int data[16];
2592 /* Create a simple polling list for analog input channel 0 */
2593 poll_list = S626_EOPL;
2594 s626_reset_adc(dev, &poll_list);
2596 /* Get initial ADC value */
2597 s626_ai_rinsn(dev, s, NULL, data);
2598 start_val = data[0];
2601 * VERSION 2.01 CHANGE: TIMEOUT ADDED TO PREVENT HANGED
2604 * Invoke ADCs until the new ADC value differs from the initial
2605 * value or a timeout occurs. The timeout protects against the
2606 * possibility that the driver is restarting and the ADC data is
2607 * a fixed value resulting from the applied ADC analog input
2608 * being unusually quiet or at the rail.
2610 for (index = 0; index < 500; index++) {
2611 s626_ai_rinsn(dev, s, NULL, data);
2613 if (adc_data != start_val)
2617 #endif /* SAA7146 BUG WORKAROUND */
2620 * Initialize the DAC interface
2624 * Init Audio2's output DMAC attributes:
2625 * burst length = 1 DWORD
2626 * threshold = 1 DWORD.
2628 writel(0, dev->mmio + S626_P_PCI_BT_A);
2631 * Init Audio2's output DMA physical addresses. The protection
2632 * address is set to 1 DWORD past the base address so that a
2633 * single DWORD will be transferred each time a DMA transfer is
2636 phys_buf = devpriv->ana_buf.physical_base +
2637 (S626_DAC_WDMABUF_OS * sizeof(uint32_t));
2638 writel((uint32_t)phys_buf, dev->mmio + S626_P_BASEA2_OUT);
2639 writel((uint32_t)(phys_buf + sizeof(uint32_t)),
2640 dev->mmio + S626_P_PROTA2_OUT);
2643 * Cache Audio2's output DMA buffer logical address. This is
2644 * where DAC data is buffered for A2 output DMA transfers.
2646 devpriv->dac_wbuf = (uint32_t *)devpriv->ana_buf.logical_base +
2647 S626_DAC_WDMABUF_OS;
2650 * Audio2's output channels does not use paging. The
2651 * protection violation handling bit is set so that the
2652 * DMAC will automatically halt and its PCI address pointer
2653 * will be reset when the protection address is reached.
2655 writel(8, dev->mmio + S626_P_PAGEA2_OUT);
2658 * Initialize time slot list 2 (TSL2), which is used to control
2659 * the clock generation for and serialization of data to be sent
2660 * to the DAC devices. Slot 0 is a NOP that is used to trap TSL
2661 * execution; this permits other slots to be safely modified
2662 * without first turning off the TSL sequencer (which is
2663 * apparently impossible to do). Also, SD3 (which is driven by a
2664 * pull-up resistor) is shifted in and stored to the MSB of
2665 * FB_BUFFER2 to be used as evidence that the slot sequence has
2666 * not yet finished executing.
2669 /* Slot 0: Trap TSL execution, shift 0xFF into FB_BUFFER2 */
2670 writel(S626_XSD2 | S626_RSD3 | S626_SIB_A2 | S626_EOS,
2671 dev->mmio + S626_VECTPORT(0));
2674 * Initialize slot 1, which is constant. Slot 1 causes a
2675 * DWORD to be transferred from audio channel 2's output FIFO
2676 * to the FIFO's output buffer so that it can be serialized
2677 * and sent to the DAC during subsequent slots. All remaining
2678 * slots are dynamically populated as required by the target
2682 /* Slot 1: Fetch DWORD from Audio2's output FIFO */
2683 writel(S626_LF_A2, dev->mmio + S626_VECTPORT(1));
2685 /* Start DAC's audio interface (TSL2) running */
2686 writel(S626_ACON1_DACSTART, dev->mmio + S626_P_ACON1);
2689 * Init Trim DACs to calibrated values. Do it twice because the
2690 * SAA7146 audio channel does not always reset properly and
2691 * sometimes causes the first few TrimDAC writes to malfunction.
2693 s626_load_trim_dacs(dev);
2694 ret = s626_load_trim_dacs(dev);
2699 * Manually init all gate array hardware in case this is a soft
2700 * reset (we have no way of determining whether this is a warm
2701 * or cold start). This is necessary because the gate array will
2702 * reset only in response to a PCI hard reset; there is no soft
2707 * Init all DAC outputs to 0V and init all DAC setpoint and
2710 for (chan = 0; chan < S626_DAC_CHANNELS; chan++) {
2711 ret = s626_set_dac(dev, chan, 0);
2717 s626_counters_init(dev);
2720 * Without modifying the state of the Battery Backup enab, disable
2721 * the watchdog timer, set DIO channels 0-5 to operate in the
2722 * standard DIO (vs. counter overflow) mode, disable the battery
2723 * charger, and reset the watchdog interval selector to zero.
2725 s626_write_misc2(dev, (s626_debi_read(dev, S626_LP_RDMISC2) &
2726 S626_MISC2_BATT_ENABLE));
2728 /* Initialize the digital I/O subsystem */
2734 static int s626_auto_attach(struct comedi_device *dev,
2735 unsigned long context_unused)
2737 struct pci_dev *pcidev = comedi_to_pci_dev(dev);
2738 struct s626_private *devpriv;
2739 struct comedi_subdevice *s;
2742 devpriv = comedi_alloc_devpriv(dev, sizeof(*devpriv));
2746 ret = comedi_pci_enable(dev);
2750 dev->mmio = pci_ioremap_bar(pcidev, 0);
2754 /* disable master interrupt */
2755 writel(0, dev->mmio + S626_P_IER);
2758 writel(S626_MC1_SOFT_RESET, dev->mmio + S626_P_MC1);
2760 /* DMA FIXME DMA// */
2762 ret = s626_allocate_dma_buffers(dev);
2767 ret = request_irq(pcidev->irq, s626_irq_handler, IRQF_SHARED,
2768 dev->board_name, dev);
2771 dev->irq = pcidev->irq;
2774 ret = comedi_alloc_subdevices(dev, 6);
2778 s = &dev->subdevices[0];
2779 /* analog input subdevice */
2780 s->type = COMEDI_SUBD_AI;
2781 s->subdev_flags = SDF_READABLE | SDF_DIFF;
2782 s->n_chan = S626_ADC_CHANNELS;
2783 s->maxdata = 0x3fff;
2784 s->range_table = &s626_range_table;
2785 s->len_chanlist = S626_ADC_CHANNELS;
2786 s->insn_read = s626_ai_insn_read;
2788 dev->read_subdev = s;
2789 s->subdev_flags |= SDF_CMD_READ;
2790 s->do_cmd = s626_ai_cmd;
2791 s->do_cmdtest = s626_ai_cmdtest;
2792 s->cancel = s626_ai_cancel;
2795 s = &dev->subdevices[1];
2796 /* analog output subdevice */
2797 s->type = COMEDI_SUBD_AO;
2798 s->subdev_flags = SDF_WRITABLE | SDF_READABLE;
2799 s->n_chan = S626_DAC_CHANNELS;
2800 s->maxdata = 0x3fff;
2801 s->range_table = &range_bipolar10;
2802 s->insn_write = s626_ao_insn_write;
2804 ret = comedi_alloc_subdev_readback(s);
2808 s = &dev->subdevices[2];
2809 /* digital I/O subdevice */
2810 s->type = COMEDI_SUBD_DIO;
2811 s->subdev_flags = SDF_WRITABLE | SDF_READABLE;
2814 s->io_bits = 0xffff;
2815 s->private = (void *)0; /* DIO group 0 */
2816 s->range_table = &range_digital;
2817 s->insn_config = s626_dio_insn_config;
2818 s->insn_bits = s626_dio_insn_bits;
2820 s = &dev->subdevices[3];
2821 /* digital I/O subdevice */
2822 s->type = COMEDI_SUBD_DIO;
2823 s->subdev_flags = SDF_WRITABLE | SDF_READABLE;
2826 s->io_bits = 0xffff;
2827 s->private = (void *)1; /* DIO group 1 */
2828 s->range_table = &range_digital;
2829 s->insn_config = s626_dio_insn_config;
2830 s->insn_bits = s626_dio_insn_bits;
2832 s = &dev->subdevices[4];
2833 /* digital I/O subdevice */
2834 s->type = COMEDI_SUBD_DIO;
2835 s->subdev_flags = SDF_WRITABLE | SDF_READABLE;
2838 s->io_bits = 0xffff;
2839 s->private = (void *)2; /* DIO group 2 */
2840 s->range_table = &range_digital;
2841 s->insn_config = s626_dio_insn_config;
2842 s->insn_bits = s626_dio_insn_bits;
2844 s = &dev->subdevices[5];
2845 /* encoder (counter) subdevice */
2846 s->type = COMEDI_SUBD_COUNTER;
2847 s->subdev_flags = SDF_WRITABLE | SDF_READABLE | SDF_LSAMPL;
2848 s->n_chan = S626_ENCODER_CHANNELS;
2849 s->maxdata = 0xffffff;
2850 s->range_table = &range_unknown;
2851 s->insn_config = s626_enc_insn_config;
2852 s->insn_read = s626_enc_insn_read;
2853 s->insn_write = s626_enc_insn_write;
2855 ret = s626_initialize(dev);
2862 static void s626_detach(struct comedi_device *dev)
2864 struct s626_private *devpriv = dev->private;
2867 /* stop ai_command */
2868 devpriv->ai_cmd_running = 0;
2871 /* interrupt mask */
2872 /* Disable master interrupt */
2873 writel(0, dev->mmio + S626_P_IER);
2874 /* Clear board's IRQ status flag */
2875 writel(S626_IRQ_GPIO3 | S626_IRQ_RPS1,
2876 dev->mmio + S626_P_ISR);
2878 /* Disable the watchdog timer and battery charger. */
2879 s626_write_misc2(dev, 0);
2881 /* Close all interfaces on 7146 device */
2882 writel(S626_MC1_SHUTDOWN, dev->mmio + S626_P_MC1);
2883 writel(S626_ACON1_BASE, dev->mmio + S626_P_ACON1);
2886 comedi_pci_detach(dev);
2887 s626_free_dma_buffers(dev);
2890 static struct comedi_driver s626_driver = {
2891 .driver_name = "s626",
2892 .module = THIS_MODULE,
2893 .auto_attach = s626_auto_attach,
2894 .detach = s626_detach,
2897 static int s626_pci_probe(struct pci_dev *dev,
2898 const struct pci_device_id *id)
2900 return comedi_pci_auto_config(dev, &s626_driver, id->driver_data);
2904 * For devices with vendor:device id == 0x1131:0x7146 you must specify
2905 * also subvendor:subdevice ids, because otherwise it will conflict with
2906 * Philips SAA7146 media/dvb based cards.
2908 static const struct pci_device_id s626_pci_table[] = {
2909 { PCI_DEVICE_SUB(PCI_VENDOR_ID_PHILIPS, PCI_DEVICE_ID_PHILIPS_SAA7146,
2913 MODULE_DEVICE_TABLE(pci, s626_pci_table);
2915 static struct pci_driver s626_pci_driver = {
2917 .id_table = s626_pci_table,
2918 .probe = s626_pci_probe,
2919 .remove = comedi_pci_auto_unconfig,
2921 module_comedi_pci_driver(s626_driver, s626_pci_driver);
2923 MODULE_AUTHOR("Gianluca Palli <gpalli@deis.unibo.it>");
2924 MODULE_DESCRIPTION("Sensoray 626 Comedi driver module");
2925 MODULE_LICENSE("GPL");