1 /* sunzilog.c: Zilog serial driver for Sparc systems.
3 * Driver for Zilog serial chips found on Sun workstations and
4 * servers. This driver could actually be made more generic.
6 * This is based on the old drivers/sbus/char/zs.c code. A lot
7 * of code has been simply moved over directly from there but
8 * much has been rewritten. Credits therefore go out to Eddie
9 * C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell for their
12 * Copyright (C) 2002, 2006, 2007 David S. Miller (davem@davemloft.net)
15 #include <linux/module.h>
16 #include <linux/kernel.h>
17 #include <linux/errno.h>
18 #include <linux/delay.h>
19 #include <linux/tty.h>
20 #include <linux/tty_flip.h>
21 #include <linux/major.h>
22 #include <linux/string.h>
23 #include <linux/ptrace.h>
24 #include <linux/ioport.h>
25 #include <linux/slab.h>
26 #include <linux/circ_buf.h>
27 #include <linux/serial.h>
28 #include <linux/sysrq.h>
29 #include <linux/console.h>
30 #include <linux/spinlock.h>
32 #include <linux/serio.h>
34 #include <linux/init.h>
35 #include <linux/of_device.h>
40 #include <asm/setup.h>
42 #if defined(CONFIG_SERIAL_SUNZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
46 #include <linux/serial_core.h>
47 #include <linux/sunserialcore.h>
51 /* On 32-bit sparcs we need to delay after register accesses
52 * to accommodate sun4 systems, but we do not need to flush writes.
53 * On 64-bit sparc we only need to flush single writes to ensure
56 #ifndef CONFIG_SPARC64
57 #define ZSDELAY() udelay(5)
58 #define ZSDELAY_LONG() udelay(20)
59 #define ZS_WSYNC(channel) do { } while (0)
62 #define ZSDELAY_LONG()
63 #define ZS_WSYNC(__channel) \
64 readb(&((__channel)->control))
67 #define ZS_CLOCK 4915200 /* Zilog input clock rate. */
68 #define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */
71 * We wrap our port structure around the generic uart_port.
73 struct uart_sunzilog_port {
74 struct uart_port port;
76 /* IRQ servicing chain. */
77 struct uart_sunzilog_port *next;
79 /* Current values of Zilog write registers. */
80 unsigned char curregs[NUM_ZSREGS];
83 #define SUNZILOG_FLAG_CONS_KEYB 0x00000001
84 #define SUNZILOG_FLAG_CONS_MOUSE 0x00000002
85 #define SUNZILOG_FLAG_IS_CONS 0x00000004
86 #define SUNZILOG_FLAG_IS_KGDB 0x00000008
87 #define SUNZILOG_FLAG_MODEM_STATUS 0x00000010
88 #define SUNZILOG_FLAG_IS_CHANNEL_A 0x00000020
89 #define SUNZILOG_FLAG_REGS_HELD 0x00000040
90 #define SUNZILOG_FLAG_TX_STOPPED 0x00000080
91 #define SUNZILOG_FLAG_TX_ACTIVE 0x00000100
92 #define SUNZILOG_FLAG_ESCC 0x00000200
93 #define SUNZILOG_FLAG_ISR_HANDLER 0x00000400
97 unsigned char parity_mask;
98 unsigned char prev_status;
106 static void sunzilog_putchar(struct uart_port *port, int ch);
108 #define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel __iomem *)((PORT)->membase))
109 #define UART_ZILOG(PORT) ((struct uart_sunzilog_port *)(PORT))
111 #define ZS_IS_KEYB(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_KEYB)
112 #define ZS_IS_MOUSE(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_MOUSE)
113 #define ZS_IS_CONS(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CONS)
114 #define ZS_IS_KGDB(UP) ((UP)->flags & SUNZILOG_FLAG_IS_KGDB)
115 #define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & SUNZILOG_FLAG_MODEM_STATUS)
116 #define ZS_IS_CHANNEL_A(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CHANNEL_A)
117 #define ZS_REGS_HELD(UP) ((UP)->flags & SUNZILOG_FLAG_REGS_HELD)
118 #define ZS_TX_STOPPED(UP) ((UP)->flags & SUNZILOG_FLAG_TX_STOPPED)
119 #define ZS_TX_ACTIVE(UP) ((UP)->flags & SUNZILOG_FLAG_TX_ACTIVE)
121 /* Reading and writing Zilog8530 registers. The delays are to make this
122 * driver work on the Sun4 which needs a settling delay after each chip
123 * register access, other machines handle this in hardware via auxiliary
124 * flip-flops which implement the settle time we do in software.
126 * The port lock must be held and local IRQs must be disabled
127 * when {read,write}_zsreg is invoked.
129 static unsigned char read_zsreg(struct zilog_channel __iomem *channel,
132 unsigned char retval;
134 writeb(reg, &channel->control);
136 retval = readb(&channel->control);
142 static void write_zsreg(struct zilog_channel __iomem *channel,
143 unsigned char reg, unsigned char value)
145 writeb(reg, &channel->control);
147 writeb(value, &channel->control);
151 static void sunzilog_clear_fifo(struct zilog_channel __iomem *channel)
155 for (i = 0; i < 32; i++) {
156 unsigned char regval;
158 regval = readb(&channel->control);
160 if (regval & Rx_CH_AV)
163 regval = read_zsreg(channel, R1);
164 readb(&channel->data);
167 if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) {
168 writeb(ERR_RES, &channel->control);
175 /* This function must only be called when the TX is not busy. The UART
176 * port lock must be held and local interrupts disabled.
178 static int __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *regs)
184 /* Let pending transmits finish. */
185 for (i = 0; i < 1000; i++) {
186 unsigned char stat = read_zsreg(channel, R1);
192 writeb(ERR_RES, &channel->control);
196 sunzilog_clear_fifo(channel);
198 /* Disable all interrupts. */
199 write_zsreg(channel, R1,
200 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
202 /* Set parity, sync config, stop bits, and clock divisor. */
203 write_zsreg(channel, R4, regs[R4]);
205 /* Set misc. TX/RX control bits. */
206 write_zsreg(channel, R10, regs[R10]);
208 /* Set TX/RX controls sans the enable bits. */
209 write_zsreg(channel, R3, regs[R3] & ~RxENAB);
210 write_zsreg(channel, R5, regs[R5] & ~TxENAB);
212 /* Synchronous mode config. */
213 write_zsreg(channel, R6, regs[R6]);
214 write_zsreg(channel, R7, regs[R7]);
216 /* Don't mess with the interrupt vector (R2, unused by us) and
217 * master interrupt control (R9). We make sure this is setup
218 * properly at probe time then never touch it again.
221 /* Disable baud generator. */
222 write_zsreg(channel, R14, regs[R14] & ~BRENAB);
224 /* Clock mode control. */
225 write_zsreg(channel, R11, regs[R11]);
227 /* Lower and upper byte of baud rate generator divisor. */
228 write_zsreg(channel, R12, regs[R12]);
229 write_zsreg(channel, R13, regs[R13]);
231 /* Now rewrite R14, with BRENAB (if set). */
232 write_zsreg(channel, R14, regs[R14]);
234 /* External status interrupt control. */
235 write_zsreg(channel, R15, (regs[R15] | WR7pEN) & ~FIFOEN);
237 /* ESCC Extension Register */
238 r15 = read_zsreg(channel, R15);
240 write_zsreg(channel, R7, regs[R7p]);
242 /* External status interrupt and FIFO control. */
243 write_zsreg(channel, R15, regs[R15] & ~WR7pEN);
246 /* Clear FIFO bit case it is an issue */
247 regs[R15] &= ~FIFOEN;
251 /* Reset external status interrupts. */
252 write_zsreg(channel, R0, RES_EXT_INT); /* First Latch */
253 write_zsreg(channel, R0, RES_EXT_INT); /* Second Latch */
255 /* Rewrite R3/R5, this time without enables masked. */
256 write_zsreg(channel, R3, regs[R3]);
257 write_zsreg(channel, R5, regs[R5]);
259 /* Rewrite R1, this time without IRQ enabled masked. */
260 write_zsreg(channel, R1, regs[R1]);
265 /* Reprogram the Zilog channel HW registers with the copies found in the
266 * software state struct. If the transmitter is busy, we defer this update
267 * until the next TX complete interrupt. Else, we do it right now.
269 * The UART port lock must be held and local interrupts disabled.
271 static void sunzilog_maybe_update_regs(struct uart_sunzilog_port *up,
272 struct zilog_channel __iomem *channel)
274 if (!ZS_REGS_HELD(up)) {
275 if (ZS_TX_ACTIVE(up)) {
276 up->flags |= SUNZILOG_FLAG_REGS_HELD;
278 __load_zsregs(channel, up->curregs);
283 static void sunzilog_change_mouse_baud(struct uart_sunzilog_port *up)
285 unsigned int cur_cflag = up->cflag;
289 up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud);
291 brg = BPS_TO_BRG(new_baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
292 up->curregs[R12] = (brg & 0xff);
293 up->curregs[R13] = (brg >> 8) & 0xff;
294 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(&up->port));
297 static void sunzilog_kbdms_receive_chars(struct uart_sunzilog_port *up,
298 unsigned char ch, int is_break)
300 if (ZS_IS_KEYB(up)) {
301 /* Stop-A is handled by drivers/char/keyboard.c now. */
304 serio_interrupt(&up->serio, ch, 0);
306 } else if (ZS_IS_MOUSE(up)) {
307 int ret = suncore_mouse_baud_detection(ch, is_break);
311 sunzilog_change_mouse_baud(up);
319 serio_interrupt(&up->serio, ch, 0);
326 static struct tty_port *
327 sunzilog_receive_chars(struct uart_sunzilog_port *up,
328 struct zilog_channel __iomem *channel)
330 struct tty_port *port = NULL;
331 unsigned char ch, r1, flag;
333 if (up->port.state != NULL) /* Unopened serial console */
334 port = &up->port.state->port;
338 r1 = read_zsreg(channel, R1);
339 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
340 writeb(ERR_RES, &channel->control);
345 ch = readb(&channel->control);
348 /* This funny hack depends upon BRK_ABRT not interfering
349 * with the other bits we care about in R1.
354 if (!(ch & Rx_CH_AV))
357 ch = readb(&channel->data);
360 ch &= up->parity_mask;
362 if (unlikely(ZS_IS_KEYB(up)) || unlikely(ZS_IS_MOUSE(up))) {
363 sunzilog_kbdms_receive_chars(up, ch, 0);
367 /* A real serial line, record the character and status. */
369 up->port.icount.rx++;
370 if (r1 & (BRK_ABRT | PAR_ERR | Rx_OVR | CRC_ERR)) {
372 r1 &= ~(PAR_ERR | CRC_ERR);
373 up->port.icount.brk++;
374 if (uart_handle_break(&up->port))
377 else if (r1 & PAR_ERR)
378 up->port.icount.parity++;
379 else if (r1 & CRC_ERR)
380 up->port.icount.frame++;
382 up->port.icount.overrun++;
383 r1 &= up->port.read_status_mask;
386 else if (r1 & PAR_ERR)
388 else if (r1 & CRC_ERR)
391 if (uart_handle_sysrq_char(&up->port, ch) || !port)
394 if (up->port.ignore_status_mask == 0xff ||
395 (r1 & up->port.ignore_status_mask) == 0) {
396 tty_insert_flip_char(port, ch, flag);
399 tty_insert_flip_char(port, 0, TTY_OVERRUN);
405 static void sunzilog_status_handle(struct uart_sunzilog_port *up,
406 struct zilog_channel __iomem *channel)
408 unsigned char status;
410 status = readb(&channel->control);
413 writeb(RES_EXT_INT, &channel->control);
417 if (status & BRK_ABRT) {
419 sunzilog_kbdms_receive_chars(up, 0, 1);
420 if (ZS_IS_CONS(up)) {
421 /* Wait for BREAK to deassert to avoid potentially
422 * confusing the PROM.
425 status = readb(&channel->control);
427 if (!(status & BRK_ABRT))
435 if (ZS_WANTS_MODEM_STATUS(up)) {
437 up->port.icount.dsr++;
439 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
440 * But it does not tell us which bit has changed, we have to keep
441 * track of this ourselves.
443 if ((status ^ up->prev_status) ^ DCD)
444 uart_handle_dcd_change(&up->port,
446 if ((status ^ up->prev_status) ^ CTS)
447 uart_handle_cts_change(&up->port,
450 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
453 up->prev_status = status;
456 static void sunzilog_transmit_chars(struct uart_sunzilog_port *up,
457 struct zilog_channel __iomem *channel)
459 struct circ_buf *xmit;
461 if (ZS_IS_CONS(up)) {
462 unsigned char status = readb(&channel->control);
465 /* TX still busy? Just wait for the next TX done interrupt.
467 * It can occur because of how we do serial console writes. It would
468 * be nice to transmit console writes just like we normally would for
469 * a TTY line. (ie. buffered and TX interrupt driven). That is not
470 * easy because console writes cannot sleep. One solution might be
471 * to poll on enough port->xmit space becoming free. -DaveM
473 if (!(status & Tx_BUF_EMP))
477 up->flags &= ~SUNZILOG_FLAG_TX_ACTIVE;
479 if (ZS_REGS_HELD(up)) {
480 __load_zsregs(channel, up->curregs);
481 up->flags &= ~SUNZILOG_FLAG_REGS_HELD;
484 if (ZS_TX_STOPPED(up)) {
485 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED;
489 if (up->port.x_char) {
490 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
491 writeb(up->port.x_char, &channel->data);
495 up->port.icount.tx++;
500 if (up->port.state == NULL)
502 xmit = &up->port.state->xmit;
503 if (uart_circ_empty(xmit))
506 if (uart_tx_stopped(&up->port))
509 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
510 writeb(xmit->buf[xmit->tail], &channel->data);
514 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
515 up->port.icount.tx++;
517 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
518 uart_write_wakeup(&up->port);
523 writeb(RES_Tx_P, &channel->control);
528 static irqreturn_t sunzilog_interrupt(int irq, void *dev_id)
530 struct uart_sunzilog_port *up = dev_id;
533 struct zilog_channel __iomem *channel
534 = ZILOG_CHANNEL_FROM_PORT(&up->port);
535 struct tty_port *port;
538 spin_lock(&up->port.lock);
539 r3 = read_zsreg(channel, R3);
543 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
544 writeb(RES_H_IUS, &channel->control);
549 port = sunzilog_receive_chars(up, channel);
551 sunzilog_status_handle(up, channel);
553 sunzilog_transmit_chars(up, channel);
555 spin_unlock(&up->port.lock);
558 tty_flip_buffer_push(port);
562 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
564 spin_lock(&up->port.lock);
566 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
567 writeb(RES_H_IUS, &channel->control);
572 port = sunzilog_receive_chars(up, channel);
574 sunzilog_status_handle(up, channel);
576 sunzilog_transmit_chars(up, channel);
578 spin_unlock(&up->port.lock);
581 tty_flip_buffer_push(port);
589 /* A convenient way to quickly get R0 status. The caller must _not_ hold the
590 * port lock, it is acquired here.
592 static __inline__ unsigned char sunzilog_read_channel_status(struct uart_port *port)
594 struct zilog_channel __iomem *channel;
595 unsigned char status;
597 channel = ZILOG_CHANNEL_FROM_PORT(port);
598 status = readb(&channel->control);
604 /* The port lock is not held. */
605 static unsigned int sunzilog_tx_empty(struct uart_port *port)
608 unsigned char status;
611 spin_lock_irqsave(&port->lock, flags);
613 status = sunzilog_read_channel_status(port);
615 spin_unlock_irqrestore(&port->lock, flags);
617 if (status & Tx_BUF_EMP)
625 /* The port lock is held and interrupts are disabled. */
626 static unsigned int sunzilog_get_mctrl(struct uart_port *port)
628 unsigned char status;
631 status = sunzilog_read_channel_status(port);
644 /* The port lock is held and interrupts are disabled. */
645 static void sunzilog_set_mctrl(struct uart_port *port, unsigned int mctrl)
647 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port;
648 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
649 unsigned char set_bits, clear_bits;
651 set_bits = clear_bits = 0;
653 if (mctrl & TIOCM_RTS)
657 if (mctrl & TIOCM_DTR)
662 /* NOTE: Not subject to 'transmitter active' rule. */
663 up->curregs[R5] |= set_bits;
664 up->curregs[R5] &= ~clear_bits;
665 write_zsreg(channel, R5, up->curregs[R5]);
668 /* The port lock is held and interrupts are disabled. */
669 static void sunzilog_stop_tx(struct uart_port *port)
671 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port;
673 up->flags |= SUNZILOG_FLAG_TX_STOPPED;
676 /* The port lock is held and interrupts are disabled. */
677 static void sunzilog_start_tx(struct uart_port *port)
679 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port;
680 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
681 unsigned char status;
683 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
684 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED;
686 status = readb(&channel->control);
689 /* TX busy? Just wait for the TX done interrupt. */
690 if (!(status & Tx_BUF_EMP))
693 /* Send the first character to jump-start the TX done
694 * IRQ sending engine.
697 writeb(port->x_char, &channel->data);
704 struct circ_buf *xmit = &port->state->xmit;
706 writeb(xmit->buf[xmit->tail], &channel->data);
710 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
713 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
714 uart_write_wakeup(&up->port);
718 /* The port lock is held. */
719 static void sunzilog_stop_rx(struct uart_port *port)
721 struct uart_sunzilog_port *up = UART_ZILOG(port);
722 struct zilog_channel __iomem *channel;
727 channel = ZILOG_CHANNEL_FROM_PORT(port);
729 /* Disable all RX interrupts. */
730 up->curregs[R1] &= ~RxINT_MASK;
731 sunzilog_maybe_update_regs(up, channel);
734 /* The port lock is held. */
735 static void sunzilog_enable_ms(struct uart_port *port)
737 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port;
738 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
739 unsigned char new_reg;
741 new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE);
742 if (new_reg != up->curregs[R15]) {
743 up->curregs[R15] = new_reg;
745 /* NOTE: Not subject to 'transmitter active' rule. */
746 write_zsreg(channel, R15, up->curregs[R15] & ~WR7pEN);
750 /* The port lock is not held. */
751 static void sunzilog_break_ctl(struct uart_port *port, int break_state)
753 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port;
754 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
755 unsigned char set_bits, clear_bits, new_reg;
758 set_bits = clear_bits = 0;
763 clear_bits |= SND_BRK;
765 spin_lock_irqsave(&port->lock, flags);
767 new_reg = (up->curregs[R5] | set_bits) & ~clear_bits;
768 if (new_reg != up->curregs[R5]) {
769 up->curregs[R5] = new_reg;
771 /* NOTE: Not subject to 'transmitter active' rule. */
772 write_zsreg(channel, R5, up->curregs[R5]);
775 spin_unlock_irqrestore(&port->lock, flags);
778 static void __sunzilog_startup(struct uart_sunzilog_port *up)
780 struct zilog_channel __iomem *channel;
782 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
783 up->prev_status = readb(&channel->control);
785 /* Enable receiver and transmitter. */
786 up->curregs[R3] |= RxENAB;
787 up->curregs[R5] |= TxENAB;
789 up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
790 sunzilog_maybe_update_regs(up, channel);
793 static int sunzilog_startup(struct uart_port *port)
795 struct uart_sunzilog_port *up = UART_ZILOG(port);
801 spin_lock_irqsave(&port->lock, flags);
802 __sunzilog_startup(up);
803 spin_unlock_irqrestore(&port->lock, flags);
808 * The test for ZS_IS_CONS is explained by the following e-mail:
810 * From: Russell King <rmk@arm.linux.org.uk>
811 * Date: Sun, 8 Dec 2002 10:18:38 +0000
813 * On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote:
814 * > I boot my 2.5 boxes using "console=ttyS0,9600" argument,
815 * > and I noticed that something is not right with reference
816 * > counting in this case. It seems that when the console
817 * > is open by kernel initially, this is not accounted
818 * > as an open, and uart_startup is not called.
820 * That is correct. We are unable to call uart_startup when the serial
821 * console is initialised because it may need to allocate memory (as
822 * request_irq does) and the memory allocators may not have been
825 * 1. initialise the port into a state where it can send characters in the
826 * console write method.
828 * 2. don't do the actual hardware shutdown in your shutdown() method (but
829 * do the normal software shutdown - ie, free irqs etc)
832 static void sunzilog_shutdown(struct uart_port *port)
834 struct uart_sunzilog_port *up = UART_ZILOG(port);
835 struct zilog_channel __iomem *channel;
841 spin_lock_irqsave(&port->lock, flags);
843 channel = ZILOG_CHANNEL_FROM_PORT(port);
845 /* Disable receiver and transmitter. */
846 up->curregs[R3] &= ~RxENAB;
847 up->curregs[R5] &= ~TxENAB;
849 /* Disable all interrupts and BRK assertion. */
850 up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
851 up->curregs[R5] &= ~SND_BRK;
852 sunzilog_maybe_update_regs(up, channel);
854 spin_unlock_irqrestore(&port->lock, flags);
857 /* Shared by TTY driver and serial console setup. The port lock is held
858 * and local interrupts are disabled.
861 sunzilog_convert_to_zs(struct uart_sunzilog_port *up, unsigned int cflag,
862 unsigned int iflag, int brg)
865 up->curregs[R10] = NRZ;
866 up->curregs[R11] = TCBR | RCBR;
868 /* Program BAUD and clock source. */
869 up->curregs[R4] &= ~XCLK_MASK;
870 up->curregs[R4] |= X16CLK;
871 up->curregs[R12] = brg & 0xff;
872 up->curregs[R13] = (brg >> 8) & 0xff;
873 up->curregs[R14] = BRSRC | BRENAB;
875 /* Character size, stop bits, and parity. */
876 up->curregs[R3] &= ~RxN_MASK;
877 up->curregs[R5] &= ~TxN_MASK;
878 switch (cflag & CSIZE) {
880 up->curregs[R3] |= Rx5;
881 up->curregs[R5] |= Tx5;
882 up->parity_mask = 0x1f;
885 up->curregs[R3] |= Rx6;
886 up->curregs[R5] |= Tx6;
887 up->parity_mask = 0x3f;
890 up->curregs[R3] |= Rx7;
891 up->curregs[R5] |= Tx7;
892 up->parity_mask = 0x7f;
896 up->curregs[R3] |= Rx8;
897 up->curregs[R5] |= Tx8;
898 up->parity_mask = 0xff;
901 up->curregs[R4] &= ~0x0c;
903 up->curregs[R4] |= SB2;
905 up->curregs[R4] |= SB1;
907 up->curregs[R4] |= PAR_ENAB;
909 up->curregs[R4] &= ~PAR_ENAB;
910 if (!(cflag & PARODD))
911 up->curregs[R4] |= PAR_EVEN;
913 up->curregs[R4] &= ~PAR_EVEN;
915 up->port.read_status_mask = Rx_OVR;
917 up->port.read_status_mask |= CRC_ERR | PAR_ERR;
918 if (iflag & (BRKINT | PARMRK))
919 up->port.read_status_mask |= BRK_ABRT;
921 up->port.ignore_status_mask = 0;
923 up->port.ignore_status_mask |= CRC_ERR | PAR_ERR;
924 if (iflag & IGNBRK) {
925 up->port.ignore_status_mask |= BRK_ABRT;
927 up->port.ignore_status_mask |= Rx_OVR;
930 if ((cflag & CREAD) == 0)
931 up->port.ignore_status_mask = 0xff;
934 /* The port lock is not held. */
936 sunzilog_set_termios(struct uart_port *port, struct ktermios *termios,
937 struct ktermios *old)
939 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port;
943 baud = uart_get_baud_rate(port, termios, old, 1200, 76800);
945 spin_lock_irqsave(&up->port.lock, flags);
947 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
949 sunzilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg);
951 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
952 up->flags |= SUNZILOG_FLAG_MODEM_STATUS;
954 up->flags &= ~SUNZILOG_FLAG_MODEM_STATUS;
956 up->cflag = termios->c_cflag;
958 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port));
960 uart_update_timeout(port, termios->c_cflag, baud);
962 spin_unlock_irqrestore(&up->port.lock, flags);
965 static const char *sunzilog_type(struct uart_port *port)
967 struct uart_sunzilog_port *up = UART_ZILOG(port);
969 return (up->flags & SUNZILOG_FLAG_ESCC) ? "zs (ESCC)" : "zs";
972 /* We do not request/release mappings of the registers here, this
973 * happens at early serial probe time.
975 static void sunzilog_release_port(struct uart_port *port)
979 static int sunzilog_request_port(struct uart_port *port)
984 /* These do not need to do anything interesting either. */
985 static void sunzilog_config_port(struct uart_port *port, int flags)
989 /* We do not support letting the user mess with the divisor, IRQ, etc. */
990 static int sunzilog_verify_port(struct uart_port *port, struct serial_struct *ser)
995 #ifdef CONFIG_CONSOLE_POLL
996 static int sunzilog_get_poll_char(struct uart_port *port)
998 unsigned char ch, r1;
999 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port;
1000 struct zilog_channel __iomem *channel
1001 = ZILOG_CHANNEL_FROM_PORT(&up->port);
1004 r1 = read_zsreg(channel, R1);
1005 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
1006 writeb(ERR_RES, &channel->control);
1011 ch = readb(&channel->control);
1014 /* This funny hack depends upon BRK_ABRT not interfering
1015 * with the other bits we care about in R1.
1020 if (!(ch & Rx_CH_AV))
1021 return NO_POLL_CHAR;
1023 ch = readb(&channel->data);
1026 ch &= up->parity_mask;
1030 static void sunzilog_put_poll_char(struct uart_port *port,
1033 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *)port;
1035 sunzilog_putchar(&up->port, ch);
1037 #endif /* CONFIG_CONSOLE_POLL */
1039 static struct uart_ops sunzilog_pops = {
1040 .tx_empty = sunzilog_tx_empty,
1041 .set_mctrl = sunzilog_set_mctrl,
1042 .get_mctrl = sunzilog_get_mctrl,
1043 .stop_tx = sunzilog_stop_tx,
1044 .start_tx = sunzilog_start_tx,
1045 .stop_rx = sunzilog_stop_rx,
1046 .enable_ms = sunzilog_enable_ms,
1047 .break_ctl = sunzilog_break_ctl,
1048 .startup = sunzilog_startup,
1049 .shutdown = sunzilog_shutdown,
1050 .set_termios = sunzilog_set_termios,
1051 .type = sunzilog_type,
1052 .release_port = sunzilog_release_port,
1053 .request_port = sunzilog_request_port,
1054 .config_port = sunzilog_config_port,
1055 .verify_port = sunzilog_verify_port,
1056 #ifdef CONFIG_CONSOLE_POLL
1057 .poll_get_char = sunzilog_get_poll_char,
1058 .poll_put_char = sunzilog_put_poll_char,
1062 static int uart_chip_count;
1063 static struct uart_sunzilog_port *sunzilog_port_table;
1064 static struct zilog_layout __iomem **sunzilog_chip_regs;
1066 static struct uart_sunzilog_port *sunzilog_irq_chain;
1068 static struct uart_driver sunzilog_reg = {
1069 .owner = THIS_MODULE,
1070 .driver_name = "sunzilog",
1075 static int __init sunzilog_alloc_tables(int num_sunzilog)
1077 struct uart_sunzilog_port *up;
1079 int num_channels = num_sunzilog * 2;
1082 size = num_channels * sizeof(struct uart_sunzilog_port);
1083 sunzilog_port_table = kzalloc(size, GFP_KERNEL);
1084 if (!sunzilog_port_table)
1087 for (i = 0; i < num_channels; i++) {
1088 up = &sunzilog_port_table[i];
1090 spin_lock_init(&up->port.lock);
1093 sunzilog_irq_chain = up;
1095 if (i < num_channels - 1)
1101 size = num_sunzilog * sizeof(struct zilog_layout __iomem *);
1102 sunzilog_chip_regs = kzalloc(size, GFP_KERNEL);
1103 if (!sunzilog_chip_regs) {
1104 kfree(sunzilog_port_table);
1105 sunzilog_irq_chain = NULL;
1112 static void sunzilog_free_tables(void)
1114 kfree(sunzilog_port_table);
1115 sunzilog_irq_chain = NULL;
1116 kfree(sunzilog_chip_regs);
1119 #define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */
1121 static void sunzilog_putchar(struct uart_port *port, int ch)
1123 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
1124 int loops = ZS_PUT_CHAR_MAX_DELAY;
1126 /* This is a timed polling loop so do not switch the explicit
1127 * udelay with ZSDELAY as that is a NOP on some platforms. -DaveM
1130 unsigned char val = readb(&channel->control);
1131 if (val & Tx_BUF_EMP) {
1138 writeb(ch, &channel->data);
1145 static DEFINE_SPINLOCK(sunzilog_serio_lock);
1147 static int sunzilog_serio_write(struct serio *serio, unsigned char ch)
1149 struct uart_sunzilog_port *up = serio->port_data;
1150 unsigned long flags;
1152 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1154 sunzilog_putchar(&up->port, ch);
1156 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1161 static int sunzilog_serio_open(struct serio *serio)
1163 struct uart_sunzilog_port *up = serio->port_data;
1164 unsigned long flags;
1167 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1168 if (!up->serio_open) {
1173 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1178 static void sunzilog_serio_close(struct serio *serio)
1180 struct uart_sunzilog_port *up = serio->port_data;
1181 unsigned long flags;
1183 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1185 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1188 #endif /* CONFIG_SERIO */
1190 #ifdef CONFIG_SERIAL_SUNZILOG_CONSOLE
1192 sunzilog_console_write(struct console *con, const char *s, unsigned int count)
1194 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index];
1195 unsigned long flags;
1198 local_irq_save(flags);
1199 if (up->port.sysrq) {
1201 } else if (oops_in_progress) {
1202 locked = spin_trylock(&up->port.lock);
1204 spin_lock(&up->port.lock);
1206 uart_console_write(&up->port, s, count, sunzilog_putchar);
1210 spin_unlock(&up->port.lock);
1211 local_irq_restore(flags);
1214 static int __init sunzilog_console_setup(struct console *con, char *options)
1216 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index];
1217 unsigned long flags;
1220 if (up->port.type != PORT_SUNZILOG)
1223 printk(KERN_INFO "Console: ttyS%d (SunZilog zs%d)\n",
1224 (sunzilog_reg.minor - 64) + con->index, con->index);
1226 /* Get firmware console settings. */
1227 sunserial_console_termios(con, up->port.dev->of_node);
1229 /* Firmware console speed is limited to 150-->38400 baud so
1230 * this hackish cflag thing is OK.
1232 switch (con->cflag & CBAUD) {
1233 case B150: baud = 150; break;
1234 case B300: baud = 300; break;
1235 case B600: baud = 600; break;
1236 case B1200: baud = 1200; break;
1237 case B2400: baud = 2400; break;
1238 case B4800: baud = 4800; break;
1239 default: case B9600: baud = 9600; break;
1240 case B19200: baud = 19200; break;
1241 case B38400: baud = 38400; break;
1244 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1246 spin_lock_irqsave(&up->port.lock, flags);
1248 up->curregs[R15] |= BRKIE;
1249 sunzilog_convert_to_zs(up, con->cflag, 0, brg);
1251 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS);
1252 __sunzilog_startup(up);
1254 spin_unlock_irqrestore(&up->port.lock, flags);
1259 static struct console sunzilog_console_ops = {
1261 .write = sunzilog_console_write,
1262 .device = uart_console_device,
1263 .setup = sunzilog_console_setup,
1264 .flags = CON_PRINTBUFFER,
1266 .data = &sunzilog_reg,
1269 static inline struct console *SUNZILOG_CONSOLE(void)
1271 return &sunzilog_console_ops;
1275 #define SUNZILOG_CONSOLE() (NULL)
1278 static void sunzilog_init_kbdms(struct uart_sunzilog_port *up)
1282 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) {
1283 up->cflag = B1200 | CS8 | CLOCAL | CREAD;
1286 up->cflag = B4800 | CS8 | CLOCAL | CREAD;
1290 up->curregs[R15] |= BRKIE;
1291 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1292 sunzilog_convert_to_zs(up, up->cflag, 0, brg);
1293 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS);
1294 __sunzilog_startup(up);
1298 static void sunzilog_register_serio(struct uart_sunzilog_port *up)
1300 struct serio *serio = &up->serio;
1302 serio->port_data = up;
1304 serio->id.type = SERIO_RS232;
1305 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) {
1306 serio->id.proto = SERIO_SUNKBD;
1307 strlcpy(serio->name, "zskbd", sizeof(serio->name));
1309 serio->id.proto = SERIO_SUN;
1310 serio->id.extra = 1;
1311 strlcpy(serio->name, "zsms", sizeof(serio->name));
1313 strlcpy(serio->phys,
1314 ((up->flags & SUNZILOG_FLAG_CONS_KEYB) ?
1315 "zs/serio0" : "zs/serio1"),
1316 sizeof(serio->phys));
1318 serio->write = sunzilog_serio_write;
1319 serio->open = sunzilog_serio_open;
1320 serio->close = sunzilog_serio_close;
1321 serio->dev.parent = up->port.dev;
1323 serio_register_port(serio);
1327 static void sunzilog_init_hw(struct uart_sunzilog_port *up)
1329 struct zilog_channel __iomem *channel;
1330 unsigned long flags;
1333 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1335 spin_lock_irqsave(&up->port.lock, flags);
1336 if (ZS_IS_CHANNEL_A(up)) {
1337 write_zsreg(channel, R9, FHWRES);
1339 (void) read_zsreg(channel, R0);
1342 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB |
1343 SUNZILOG_FLAG_CONS_MOUSE)) {
1344 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
1345 up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
1346 up->curregs[R3] = RxENAB | Rx8;
1347 up->curregs[R5] = TxENAB | Tx8;
1348 up->curregs[R6] = 0x00; /* SDLC Address */
1349 up->curregs[R7] = 0x7E; /* SDLC Flag */
1350 up->curregs[R9] = NV;
1351 up->curregs[R7p] = 0x00;
1352 sunzilog_init_kbdms(up);
1353 /* Only enable interrupts if an ISR handler available */
1354 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER)
1355 up->curregs[R9] |= MIE;
1356 write_zsreg(channel, R9, up->curregs[R9]);
1358 /* Normal serial TTY. */
1359 up->parity_mask = 0xff;
1360 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
1361 up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
1362 up->curregs[R3] = RxENAB | Rx8;
1363 up->curregs[R5] = TxENAB | Tx8;
1364 up->curregs[R6] = 0x00; /* SDLC Address */
1365 up->curregs[R7] = 0x7E; /* SDLC Flag */
1366 up->curregs[R9] = NV;
1367 up->curregs[R10] = NRZ;
1368 up->curregs[R11] = TCBR | RCBR;
1370 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1371 up->curregs[R12] = (brg & 0xff);
1372 up->curregs[R13] = (brg >> 8) & 0xff;
1373 up->curregs[R14] = BRSRC | BRENAB;
1374 up->curregs[R15] = FIFOEN; /* Use FIFO if on ESCC */
1375 up->curregs[R7p] = TxFIFO_LVL | RxFIFO_LVL;
1376 if (__load_zsregs(channel, up->curregs)) {
1377 up->flags |= SUNZILOG_FLAG_ESCC;
1379 /* Only enable interrupts if an ISR handler available */
1380 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER)
1381 up->curregs[R9] |= MIE;
1382 write_zsreg(channel, R9, up->curregs[R9]);
1385 spin_unlock_irqrestore(&up->port.lock, flags);
1388 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB |
1389 SUNZILOG_FLAG_CONS_MOUSE))
1390 sunzilog_register_serio(up);
1394 static int zilog_irq;
1396 static int zs_probe(struct platform_device *op)
1398 static int kbm_inst, uart_inst;
1400 struct uart_sunzilog_port *up;
1401 struct zilog_layout __iomem *rp;
1402 int keyboard_mouse = 0;
1405 if (of_find_property(op->dev.of_node, "keyboard", NULL))
1408 /* uarts must come before keyboards/mice */
1410 inst = uart_chip_count + kbm_inst;
1414 sunzilog_chip_regs[inst] = of_ioremap(&op->resource[0], 0,
1415 sizeof(struct zilog_layout),
1417 if (!sunzilog_chip_regs[inst])
1420 rp = sunzilog_chip_regs[inst];
1423 zilog_irq = op->archdata.irqs[0];
1425 up = &sunzilog_port_table[inst * 2];
1428 up[0].port.mapbase = op->resource[0].start + 0x00;
1429 up[0].port.membase = (void __iomem *) &rp->channelA;
1430 up[0].port.iotype = UPIO_MEM;
1431 up[0].port.irq = op->archdata.irqs[0];
1432 up[0].port.uartclk = ZS_CLOCK;
1433 up[0].port.fifosize = 1;
1434 up[0].port.ops = &sunzilog_pops;
1435 up[0].port.type = PORT_SUNZILOG;
1436 up[0].port.flags = 0;
1437 up[0].port.line = (inst * 2) + 0;
1438 up[0].port.dev = &op->dev;
1439 up[0].flags |= SUNZILOG_FLAG_IS_CHANNEL_A;
1441 up[0].flags |= SUNZILOG_FLAG_CONS_KEYB;
1442 sunzilog_init_hw(&up[0]);
1445 up[1].port.mapbase = op->resource[0].start + 0x04;
1446 up[1].port.membase = (void __iomem *) &rp->channelB;
1447 up[1].port.iotype = UPIO_MEM;
1448 up[1].port.irq = op->archdata.irqs[0];
1449 up[1].port.uartclk = ZS_CLOCK;
1450 up[1].port.fifosize = 1;
1451 up[1].port.ops = &sunzilog_pops;
1452 up[1].port.type = PORT_SUNZILOG;
1453 up[1].port.flags = 0;
1454 up[1].port.line = (inst * 2) + 1;
1455 up[1].port.dev = &op->dev;
1458 up[1].flags |= SUNZILOG_FLAG_CONS_MOUSE;
1459 sunzilog_init_hw(&up[1]);
1461 if (!keyboard_mouse) {
1462 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node,
1463 &sunzilog_reg, up[0].port.line,
1465 up->flags |= SUNZILOG_FLAG_IS_CONS;
1466 err = uart_add_one_port(&sunzilog_reg, &up[0].port);
1468 of_iounmap(&op->resource[0],
1469 rp, sizeof(struct zilog_layout));
1472 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node,
1473 &sunzilog_reg, up[1].port.line,
1475 up->flags |= SUNZILOG_FLAG_IS_CONS;
1476 err = uart_add_one_port(&sunzilog_reg, &up[1].port);
1478 uart_remove_one_port(&sunzilog_reg, &up[0].port);
1479 of_iounmap(&op->resource[0],
1480 rp, sizeof(struct zilog_layout));
1485 printk(KERN_INFO "%s: Keyboard at MMIO 0x%llx (irq = %d) "
1488 (unsigned long long) up[0].port.mapbase,
1489 op->archdata.irqs[0], sunzilog_type(&up[0].port));
1490 printk(KERN_INFO "%s: Mouse at MMIO 0x%llx (irq = %d) "
1493 (unsigned long long) up[1].port.mapbase,
1494 op->archdata.irqs[0], sunzilog_type(&up[1].port));
1498 dev_set_drvdata(&op->dev, &up[0]);
1503 static void zs_remove_one(struct uart_sunzilog_port *up)
1505 if (ZS_IS_KEYB(up) || ZS_IS_MOUSE(up)) {
1507 serio_unregister_port(&up->serio);
1510 uart_remove_one_port(&sunzilog_reg, &up->port);
1513 static int zs_remove(struct platform_device *op)
1515 struct uart_sunzilog_port *up = dev_get_drvdata(&op->dev);
1516 struct zilog_layout __iomem *regs;
1518 zs_remove_one(&up[0]);
1519 zs_remove_one(&up[1]);
1521 regs = sunzilog_chip_regs[up[0].port.line / 2];
1522 of_iounmap(&op->resource[0], regs, sizeof(struct zilog_layout));
1524 dev_set_drvdata(&op->dev, NULL);
1529 static const struct of_device_id zs_match[] = {
1535 MODULE_DEVICE_TABLE(of, zs_match);
1537 static struct platform_driver zs_driver = {
1540 .owner = THIS_MODULE,
1541 .of_match_table = zs_match,
1544 .remove = zs_remove,
1547 static int __init sunzilog_init(void)
1549 struct device_node *dp;
1552 int num_sunzilog = 0;
1554 for_each_node_by_name(dp, "zs") {
1556 if (of_find_property(dp, "keyboard", NULL))
1561 err = sunzilog_alloc_tables(num_sunzilog);
1565 uart_chip_count = num_sunzilog - num_keybms;
1567 err = sunserial_register_minors(&sunzilog_reg,
1568 uart_chip_count * 2);
1570 goto out_free_tables;
1573 err = platform_driver_register(&zs_driver);
1575 goto out_unregister_uart;
1578 struct uart_sunzilog_port *up = sunzilog_irq_chain;
1579 err = request_irq(zilog_irq, sunzilog_interrupt, IRQF_SHARED,
1580 "zs", sunzilog_irq_chain);
1582 goto out_unregister_driver;
1584 /* Enable Interrupts */
1586 struct zilog_channel __iomem *channel;
1588 /* printk (KERN_INFO "Enable IRQ for ZILOG Hardware %p\n", up); */
1589 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1590 up->flags |= SUNZILOG_FLAG_ISR_HANDLER;
1591 up->curregs[R9] |= MIE;
1592 write_zsreg(channel, R9, up->curregs[R9]);
1600 out_unregister_driver:
1601 platform_driver_unregister(&zs_driver);
1603 out_unregister_uart:
1605 sunserial_unregister_minors(&sunzilog_reg, num_sunzilog);
1606 sunzilog_reg.cons = NULL;
1610 sunzilog_free_tables();
1614 static void __exit sunzilog_exit(void)
1616 platform_driver_unregister(&zs_driver);
1619 struct uart_sunzilog_port *up = sunzilog_irq_chain;
1621 /* Disable Interrupts */
1623 struct zilog_channel __iomem *channel;
1625 /* printk (KERN_INFO "Disable IRQ for ZILOG Hardware %p\n", up); */
1626 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1627 up->flags &= ~SUNZILOG_FLAG_ISR_HANDLER;
1628 up->curregs[R9] &= ~MIE;
1629 write_zsreg(channel, R9, up->curregs[R9]);
1633 free_irq(zilog_irq, sunzilog_irq_chain);
1637 if (sunzilog_reg.nr) {
1638 sunserial_unregister_minors(&sunzilog_reg, sunzilog_reg.nr);
1639 sunzilog_free_tables();
1643 module_init(sunzilog_init);
1644 module_exit(sunzilog_exit);
1646 MODULE_AUTHOR("David S. Miller");
1647 MODULE_DESCRIPTION("Sun Zilog serial port driver");
1648 MODULE_VERSION("2.0");
1649 MODULE_LICENSE("GPL");