2 # Physical Layer USB driver configuration
4 menu "USB Physical Layer drivers"
10 # USB Transceiver Drivers
13 tristate "AB8500 USB Transceiver Driver"
14 depends on AB8500_CORE
17 Enable this to support the USB OTG transceiver in AB8500 chip.
18 This transceiver supports high and full speed devices plus,
19 in host mode, low speed.
22 bool "Freescale USB OTG Transceiver Driver"
23 depends on USB_EHCI_FSL && USB_FSL_USB2 && PM_RUNTIME
27 Enable this to support Freescale USB OTG transceiver.
30 tristate "Philips ISP1301 with OMAP OTG"
31 depends on I2C && ARCH_OMAP_OTG
34 If you say yes here you get support for the Philips ISP1301
35 USB-On-The-Go transceiver working with the OMAP OTG controller.
36 The ISP1301 is a full speed USB transceiver which is used in
37 products including H2, H3, and H4 development boards for Texas
38 Instruments OMAP processors.
40 This driver can also be built as a module. If so, the module
41 will be called isp1301_omap.
44 bool "Marvell USB 3.0 PHY controller Driver"
48 Enable this to support Marvell USB 3.0 phy controller for Marvell
52 tristate "NOP USB Transceiver Driver"
55 This driver is to be used by all the usb transceiver which are either
56 built-in with usb ip or which are autonomous and doesn't require any
57 phy programming such as ISP1x04 etc.
59 config OMAP_CONTROL_USB
60 tristate "OMAP CONTROL USB Driver"
61 depends on ARCH_OMAP2PLUS || COMPILE_TEST
63 Enable this to add support for the USB part present in the control
64 module. This driver has API to power on the USB2 PHY and to write to
65 the mailbox. The mailbox is present only in omap4 and the register to
66 power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
67 additional register to power on USB3 PHY.
70 tristate "OMAP USB3 PHY Driver"
71 depends on ARCH_OMAP2PLUS || COMPILE_TEST
72 select OMAP_CONTROL_USB
75 Enable this to support the USB3 PHY that is part of SOC. This
76 driver takes care of all the PHY functionality apart from comparator.
77 This driver interacts with the "OMAP Control USB Driver" to power
80 config AM335X_CONTROL_USB
84 tristate "AM335x USB PHY Driver"
85 depends on ARM || COMPILE_TEST
87 select AM335X_CONTROL_USB
90 This driver provides PHY support for that phy which part for the
96 Enable this to support Samsung USB phy helper driver for Samsung SoCs.
97 This driver provides common interface to interact, for Samsung USB 2.0 PHY
98 driver and later for Samsung USB 3.0 PHY driver.
100 config SAMSUNG_USB2PHY
101 tristate "Samsung USB 2.0 PHY controller Driver"
102 select SAMSUNG_USBPHY
105 Enable this to support Samsung USB 2.0 (High Speed) PHY controller
106 driver for Samsung SoCs.
108 config SAMSUNG_USB3PHY
109 tristate "Samsung USB 3.0 PHY controller Driver"
110 select SAMSUNG_USBPHY
113 Enable this to support Samsung USB 3.0 (Super Speed) phy controller
117 tristate "TWL4030 USB Transceiver Driver"
118 depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
121 Enable this to support the USB OTG transceiver on TWL4030
122 family chips (including the TWL5030 and TPS659x0 devices).
123 This transceiver supports high and full speed devices plus,
124 in host mode, low speed.
127 tristate "TWL6030 USB Transceiver Driver"
128 depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
130 Enable this to support the USB OTG transceiver on TWL6030
131 family chips. This TWL6030 transceiver has the VBUS and ID GND
132 and OTG SRP events capabilities. For all other transceiver functionality
133 UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
134 are hooked to this driver through platform_data structure.
135 The definition of internal PHY APIs are in the mach-omap2 layer.
138 tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
142 Provides simple GPIO VBUS sensing for controllers with an
143 internal transceiver via the usb_phy interface, and
144 optionally control of a D+ pullup GPIO as well as a VBUS
145 current limit regulator.
148 tristate "NXP ISP1301 USB transceiver support"
149 depends on USB || USB_GADGET
153 Say Y here to add support for the NXP ISP1301 USB transceiver driver.
154 This chip is typically used as USB transceiver for USB host, gadget
155 and OTG drivers (to be selected separately).
157 To compile this driver as a module, choose M here: the
158 module will be called isp1301.
161 tristate "OTG support for Qualcomm on-chip USB controller"
162 depends on (USB || USB_GADGET) && ARCH_MSM
165 Enable this to support the USB OTG transceiver on MSM chips. It
166 handles PHY initialization, clock management, and workarounds
167 required after resetting the hardware and power management.
168 This driver is required even for peripheral only or host only
170 This driver is not supported on boards like trout which
174 tristate "Marvell USB OTG support"
175 depends on USB_EHCI_MV && USB_MV_UDC && PM_RUNTIME
179 Say Y here if you want to build Marvell USB OTG transciever
180 driver in kernel (including PXA and MMP series). This driver
181 implements role switch between EHCI host driver and gadget driver.
183 To compile this driver as a module, choose M here.
186 tristate "Freescale MXS USB PHY support"
187 depends on ARCH_MXC || ARCH_MXS
191 Enable this to support the Freescale MXS USB PHY.
193 MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
196 tristate "Renesas R-Car USB PHY support"
197 depends on USB || USB_GADGET
200 Say Y here to add support for the Renesas R-Car USB common PHY driver.
201 This chip is typically used as USB PHY for USB host, gadget.
202 This driver supports R8A7778 and R8A7779.
204 To compile this driver as a module, choose M here: the
205 module will be called phy-rcar-usb.
208 bool "Generic ULPI Transceiver Driver"
211 Enable this to support ULPI connected USB OTG transceivers which
212 are likely found on embedded boards.
214 config USB_ULPI_VIEWPORT
218 Provides read/write operations to the ULPI phy register set for
219 controllers with a viewport register (e.g. Chipidea/ARC controllers).