2 # Physical Layer USB driver configuration
4 menu "USB Physical Layer drivers"
10 # USB Transceiver Drivers
13 tristate "AB8500 USB Transceiver Driver"
14 depends on AB8500_CORE
17 Enable this to support the USB OTG transceiver in AB8500 chip.
18 This transceiver supports high and full speed devices plus,
19 in host mode, low speed.
22 bool "Freescale USB OTG Transceiver Driver"
23 depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM_RUNTIME
27 Enable this to support Freescale USB OTG transceiver.
30 tristate "Philips ISP1301 with OMAP OTG"
31 depends on I2C && ARCH_OMAP_OTG
35 If you say yes here you get support for the Philips ISP1301
36 USB-On-The-Go transceiver working with the OMAP OTG controller.
37 The ISP1301 is a full speed USB transceiver which is used in
38 products including H2, H3, and H4 development boards for Texas
39 Instruments OMAP processors.
41 This driver can also be built as a module. If so, the module
42 will be called phy-isp1301-omap.
44 config KEYSTONE_USB_PHY
45 tristate "Keystone USB PHY Driver"
46 depends on ARCH_KEYSTONE || COMPILE_TEST
49 Enable this to support Keystone USB phy. This driver provides
50 interface to interact with USB 2.0 and USB 3.0 PHY that is part
54 tristate "NOP USB Transceiver Driver"
57 This driver is to be used by all the usb transceiver which are either
58 built-in with usb ip or which are autonomous and doesn't require any
59 phy programming such as ISP1x04 etc.
61 config AM335X_CONTROL_USB
65 tristate "AM335x USB PHY Driver"
66 depends on ARM || COMPILE_TEST
68 select AM335X_CONTROL_USB
71 This driver provides PHY support for that phy which part for the
77 Enable this to support Samsung USB phy helper driver for Samsung SoCs.
78 This driver provides common interface to interact, for Samsung USB 2.0 PHY
79 driver and later for Samsung USB 3.0 PHY driver.
81 config SAMSUNG_USB2PHY
82 tristate "Samsung USB 2.0 PHY controller Driver"
86 Enable this to support Samsung USB 2.0 (High Speed) PHY controller
87 driver for Samsung SoCs.
89 config SAMSUNG_USB3PHY
90 tristate "Samsung USB 3.0 PHY controller Driver"
94 Enable this to support Samsung USB 3.0 (Super Speed) phy controller
98 tristate "TWL6030 USB Transceiver Driver"
99 depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
101 Enable this to support the USB OTG transceiver on TWL6030
102 family chips. This TWL6030 transceiver has the VBUS and ID GND
103 and OTG SRP events capabilities. For all other transceiver functionality
104 UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
105 are hooked to this driver through platform_data structure.
106 The definition of internal PHY APIs are in the mach-omap2 layer.
109 tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
113 Provides simple GPIO VBUS sensing for controllers with an
114 internal transceiver via the usb_phy interface, and
115 optionally control of a D+ pullup GPIO as well as a VBUS
116 current limit regulator.
119 tristate "OMAP USB OTG controller driver"
120 depends on ARCH_OMAP_OTG && EXTCON
122 Enable this to support some transceivers on OMAP1 platforms. OTG
123 controller is needed to switch between host and peripheral modes.
125 This driver can also be built as a module. If so, the module
126 will be called phy-omap-otg.
129 tristate "Tahvo USB transceiver driver"
130 depends on MFD_RETU && EXTCON
133 Enable this to support USB transceiver on Tahvo. This is used
134 at least on Nokia 770.
136 config TAHVO_USB_HOST_BY_DEFAULT
138 boolean "Device in USB host mode by default"
140 Say Y here, if you want the device to enter USB host mode
141 by default on bootup.
144 tristate "NXP ISP1301 USB transceiver support"
145 depends on USB || USB_GADGET
149 Say Y here to add support for the NXP ISP1301 USB transceiver driver.
150 This chip is typically used as USB transceiver for USB host, gadget
151 and OTG drivers (to be selected separately).
153 To compile this driver as a module, choose M here: the
154 module will be called phy-isp1301.
157 tristate "Qualcomm on-chip USB OTG controller support"
158 depends on (USB || USB_GADGET) && (ARCH_MSM || ARCH_QCOM || COMPILE_TEST)
159 depends on RESET_CONTROLLER
162 Enable this to support the USB OTG transceiver on Qualcomm chips. It
163 handles PHY initialization, clock management, and workarounds
164 required after resetting the hardware and power management.
165 This driver is required even for peripheral only or host only
167 This driver is not supported on boards like trout which
171 tristate "Marvell USB OTG support"
172 depends on USB_EHCI_MV && USB_MV_UDC && PM_RUNTIME
176 Say Y here if you want to build Marvell USB OTG transciever
177 driver in kernel (including PXA and MMP series). This driver
178 implements role switch between EHCI host driver and gadget driver.
180 To compile this driver as a module, choose M here.
183 tristate "Freescale MXS USB PHY support"
184 depends on ARCH_MXC || ARCH_MXS
188 Enable this to support the Freescale MXS USB PHY.
190 MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
193 tristate "Renesas R-Car USB PHY support"
194 depends on USB || USB_GADGET
195 depends on ARCH_R8A7778 || ARCH_R8A7779 || COMPILE_TEST
198 Say Y here to add support for the Renesas R-Car USB common PHY driver.
199 This chip is typically used as USB PHY for USB host, gadget.
200 This driver supports R8A7778 and R8A7779.
202 To compile this driver as a module, choose M here: the
203 module will be called phy-rcar-usb.
205 config USB_RCAR_GEN2_PHY
206 tristate "Renesas R-Car Gen2 USB PHY support"
207 depends on ARCH_R8A7790 || ARCH_R8A7791 || COMPILE_TEST
210 Say Y here to add support for the Renesas R-Car Gen2 USB PHY driver.
211 It is typically used to control internal USB PHY for USBHS,
212 and to configure shared USB channels 0 and 2.
213 This driver supports R8A7790 and R8A7791.
215 To compile this driver as a module, choose M here: the
216 module will be called phy-rcar-gen2-usb.
219 bool "Generic ULPI Transceiver Driver"
220 depends on ARM || ARM64
222 Enable this to support ULPI connected USB OTG transceivers which
223 are likely found on embedded boards.
225 config USB_ULPI_VIEWPORT
229 Provides read/write operations to the ULPI phy register set for
230 controllers with a viewport register (e.g. Chipidea/ARC controllers).