drivers/usb/serial/io_edgeport.c

   1 /*
   2  * Edgeport USB Serial Converter driver
   3  *
   4  * Copyright (C) 2000 Inside Out Networks, All rights reserved.
   5  * Copyright (C) 2001-2002 Greg Kroah-Hartman <greg@kroah.com>
   6  *
   7  *      This program is free software; you can redistribute it and/or modify
   8  *      it under the terms of the GNU General Public License as published by
   9  *      the Free Software Foundation; either version 2 of the License, or
  10  *      (at your option) any later version.
  11  *
  12  * Supports the following devices:
  13  *      Edgeport/4
  14  *      Edgeport/4t
  15  *      Edgeport/2
  16  *      Edgeport/4i
  17  *      Edgeport/2i
  18  *      Edgeport/421
  19  *      Edgeport/21
  20  *      Rapidport/4
  21  *      Edgeport/8
  22  *      Edgeport/2D8
  23  *      Edgeport/4D8
  24  *      Edgeport/8i
  25  *
  26  * For questions or problems with this driver, contact Inside Out
  27  * Networks technical support, or Peter Berger <pberger@brimson.com>,
  28  * or Al Borchers <alborchers@steinerpoint.com>.
  29  *
  30  */
  31
  32 #include <linux/kernel.h>
  33 #include <linux/jiffies.h>
  34 #include <linux/errno.h>
  35 #include <linux/init.h>
  36 #include <linux/slab.h>
  37 #include <linux/tty.h>
  38 #include <linux/tty_driver.h>
  39 #include <linux/tty_flip.h>
  40 #include <linux/module.h>
  41 #include <linux/spinlock.h>
  42 #include <linux/serial.h>
  43 #include <linux/ioctl.h>
  44 #include <linux/wait.h>
  45 #include <linux/firmware.h>
  46 #include <linux/ihex.h>
  47 #include <linux/uaccess.h>
  48 #include <linux/usb.h>
  49 #include <linux/usb/serial.h>
  50 #include "io_edgeport.h"
  51 #include "io_ionsp.h"           /* info for the iosp messages */
  52 #include "io_16654.h"           /* 16654 UART defines */
  53
  54 #define DRIVER_AUTHOR "Greg Kroah-Hartman <greg@kroah.com> and David Iacovelli"
  55 #define DRIVER_DESC "Edgeport USB Serial Driver"
  56
  57 #define MAX_NAME_LEN            64
  58
  59 #define CHASE_TIMEOUT           (5*HZ)          /* 5 seconds */
  60 #define OPEN_TIMEOUT            (5*HZ)          /* 5 seconds */
  61 #define COMMAND_TIMEOUT         (5*HZ)          /* 5 seconds */
  62
  63 /* receive port state */
  64 enum RXSTATE {
  65         EXPECT_HDR1 = 0,    /* Expect header byte 1 */
  66         EXPECT_HDR2 = 1,    /* Expect header byte 2 */
  67         EXPECT_DATA = 2,    /* Expect 'RxBytesRemaining' data */
  68         EXPECT_HDR3 = 3,    /* Expect header byte 3 (for status hdrs only) */
  69 };
  70
  71
  72 /* Transmit Fifo
  73  * This Transmit queue is an extension of the edgeport Rx buffer.
  74  * The maximum amount of data buffered in both the edgeport
  75  * Rx buffer (maxTxCredits) and this buffer will never exceed maxTxCredits.
  76  */
  77 struct TxFifo {
  78         unsigned int    head;   /* index to head pointer (write) */
  79         unsigned int    tail;   /* index to tail pointer (read)  */
  80         unsigned int    count;  /* Bytes in queue */
  81         unsigned int    size;   /* Max size of queue (equal to Max number of TxCredits) */
  82         unsigned char   *fifo;  /* allocated Buffer */
  83 };
  84
  85 /* This structure holds all of the local port information */
  86 struct edgeport_port {
  87         __u16                   txCredits;              /* our current credits for this port */
  88         __u16                   maxTxCredits;           /* the max size of the port */
  89
  90         struct TxFifo           txfifo;                 /* transmit fifo -- size will be maxTxCredits */
  91         struct urb              *write_urb;             /* write URB for this port */
  92         bool                    write_in_progress;      /* 'true' while a write URB is outstanding */
  93         spinlock_t              ep_lock;
  94
  95         __u8                    shadowLCR;              /* last LCR value received */
  96         __u8                    shadowMCR;              /* last MCR value received */
  97         __u8                    shadowMSR;              /* last MSR value received */
  98         __u8                    shadowLSR;              /* last LSR value received */
  99         __u8                    shadowXonChar;          /* last value set as XON char in Edgeport */
 100         __u8                    shadowXoffChar;         /* last value set as XOFF char in Edgeport */
 101         __u8                    validDataMask;
 102         __u32                   baudRate;
 103
 104         bool                    open;
 105         bool                    openPending;
 106         bool                    commandPending;
 107         bool                    closePending;
 108         bool                    chaseResponsePending;
 109
 110         wait_queue_head_t       wait_chase;             /* for handling sleeping while waiting for chase to finish */
 111         wait_queue_head_t       wait_open;              /* for handling sleeping while waiting for open to finish */
 112         wait_queue_head_t       wait_command;           /* for handling sleeping while waiting for command to finish */
 113         wait_queue_head_t       delta_msr_wait;         /* for handling sleeping while waiting for msr change to happen */
 114
 115         struct async_icount     icount;
 116         struct usb_serial_port  *port;                  /* loop back to the owner of this object */
 117 };
 118
 119
 120 /* This structure holds all of the individual device information */
 121 struct edgeport_serial {
 122         char                    name[MAX_NAME_LEN+2];           /* string name of this device */
 123
 124         struct edge_manuf_descriptor    manuf_descriptor;       /* the manufacturer descriptor */
 125         struct edge_boot_descriptor     boot_descriptor;        /* the boot firmware descriptor */
 126         struct edgeport_product_info    product_info;           /* Product Info */
 127         struct edge_compatibility_descriptor epic_descriptor;   /* Edgeport compatible descriptor */
 128         int                     is_epic;                        /* flag if EPiC device or not */
 129
 130         __u8                    interrupt_in_endpoint;          /* the interrupt endpoint handle */
 131         unsigned char           *interrupt_in_buffer;           /* the buffer we use for the interrupt endpoint */
 132         struct urb              *interrupt_read_urb;            /* our interrupt urb */
 133
 134         __u8                    bulk_in_endpoint;               /* the bulk in endpoint handle */
 135         unsigned char           *bulk_in_buffer;                /* the buffer we use for the bulk in endpoint */
 136         struct urb              *read_urb;                      /* our bulk read urb */
 137         bool                    read_in_progress;
 138         spinlock_t              es_lock;
 139
 140         __u8                    bulk_out_endpoint;              /* the bulk out endpoint handle */
 141
 142         __s16                   rxBytesAvail;                   /* the number of bytes that we need to read from this device */
 143
 144         enum RXSTATE            rxState;                        /* the current state of the bulk receive processor */
 145         __u8                    rxHeader1;                      /* receive header byte 1 */
 146         __u8                    rxHeader2;                      /* receive header byte 2 */
 147         __u8                    rxHeader3;                      /* receive header byte 3 */
 148         __u8                    rxPort;                         /* the port that we are currently receiving data for */
 149         __u8                    rxStatusCode;                   /* the receive status code */
 150         __u8                    rxStatusParam;                  /* the receive status paramater */
 151         __s16                   rxBytesRemaining;               /* the number of port bytes left to read */
 152         struct usb_serial       *serial;                        /* loop back to the owner of this object */
 153 };
 154
 155 /* baud rate information */
 156 struct divisor_table_entry {
 157         __u32   BaudRate;
 158         __u16  Divisor;
 159 };
 160
 161 /*
 162  * Define table of divisors for Rev A EdgePort/4 hardware
 163  * These assume a 3.6864MHz crystal, the standard /16, and
 164  * MCR.7 = 0.
 165  */
 166
 167 static const struct divisor_table_entry divisor_table[] = {
 168         {   50,         4608},
 169         {   75,         3072},
 170         {   110,        2095},  /* 2094.545455 => 230450   => .0217 % over */
 171         {   134,        1713},  /* 1713.011152 => 230398.5 => .00065% under */
 172         {   150,        1536},
 173         {   300,        768},
 174         {   600,        384},
 175         {   1200,       192},
 176         {   1800,       128},
 177         {   2400,       96},
 178         {   4800,       48},
 179         {   7200,       32},
 180         {   9600,       24},
 181         {   14400,      16},
 182         {   19200,      12},
 183         {   38400,      6},
 184         {   57600,      4},
 185         {   115200,     2},
 186         {   230400,     1},
 187 };
 188
 189 /* Number of outstanding Command Write Urbs */
 190 static atomic_t CmdUrbs = ATOMIC_INIT(0);
 191
 192
 193 /* local function prototypes */
 194
 195 /* function prototypes for all URB callbacks */
 196 static void edge_interrupt_callback(struct urb *urb);
 197 static void edge_bulk_in_callback(struct urb *urb);
 198 static void edge_bulk_out_data_callback(struct urb *urb);
 199 static void edge_bulk_out_cmd_callback(struct urb *urb);
 200
 201 /* function prototypes for the usbserial callbacks */
 202 static int edge_open(struct tty_struct *tty, struct usb_serial_port *port);
 203 static void edge_close(struct usb_serial_port *port);
 204 static int edge_write(struct tty_struct *tty, struct usb_serial_port *port,
 205                                         const unsigned char *buf, int count);
 206 static int edge_write_room(struct tty_struct *tty);
 207 static int edge_chars_in_buffer(struct tty_struct *tty);
 208 static void edge_throttle(struct tty_struct *tty);
 209 static void edge_unthrottle(struct tty_struct *tty);
 210 static void edge_set_termios(struct tty_struct *tty,
 211                                         struct usb_serial_port *port,
 212                                         struct ktermios *old_termios);
 213 static int  edge_ioctl(struct tty_struct *tty,
 214                                         unsigned int cmd, unsigned long arg);
 215 static void edge_break(struct tty_struct *tty, int break_state);
 216 static int  edge_tiocmget(struct tty_struct *tty);
 217 static int  edge_tiocmset(struct tty_struct *tty,
 218                                         unsigned int set, unsigned int clear);
 219 static int  edge_get_icount(struct tty_struct *tty,
 220                                 struct serial_icounter_struct *icount);
 221 static int  edge_startup(struct usb_serial *serial);
 222 static void edge_disconnect(struct usb_serial *serial);
 223 static void edge_release(struct usb_serial *serial);
 224 static int edge_port_probe(struct usb_serial_port *port);
 225 static int edge_port_remove(struct usb_serial_port *port);
 226
 227 #include "io_tables.h"  /* all of the devices that this driver supports */
 228
 229 /* function prototypes for all of our local functions */
 230
 231 static void  process_rcvd_data(struct edgeport_serial *edge_serial,
 232                                 unsigned char *buffer, __u16 bufferLength);
 233 static void process_rcvd_status(struct edgeport_serial *edge_serial,
 234                                 __u8 byte2, __u8 byte3);
 235 static void edge_tty_recv(struct device *dev, struct tty_struct *tty,
 236                                 unsigned char *data, int length);
 237 static void handle_new_msr(struct edgeport_port *edge_port, __u8 newMsr);
 238 static void handle_new_lsr(struct edgeport_port *edge_port, __u8 lsrData,
 239                                 __u8 lsr, __u8 data);
 240 static int  send_iosp_ext_cmd(struct edgeport_port *edge_port, __u8 command,
 241                                 __u8 param);
 242 static int  calc_baud_rate_divisor(struct device *dev, int baud_rate, int *divisor);
 243 static int  send_cmd_write_baud_rate(struct edgeport_port *edge_port,
 244                                 int baudRate);
 245 static void change_port_settings(struct tty_struct *tty,
 246                                 struct edgeport_port *edge_port,
 247                                 struct ktermios *old_termios);
 248 static int  send_cmd_write_uart_register(struct edgeport_port *edge_port,
 249                                 __u8 regNum, __u8 regValue);
 250 static int  write_cmd_usb(struct edgeport_port *edge_port,
 251                                 unsigned char *buffer, int writeLength);
 252 static void send_more_port_data(struct edgeport_serial *edge_serial,
 253                                 struct edgeport_port *edge_port);
 254
 255 static int sram_write(struct usb_serial *serial, __u16 extAddr, __u16 addr,
 256                                         __u16 length, const __u8 *data);
 257 static int rom_read(struct usb_serial *serial, __u16 extAddr, __u16 addr,
 258                                                 __u16 length, __u8 *data);
 259 static int rom_write(struct usb_serial *serial, __u16 extAddr, __u16 addr,
 260                                         __u16 length, const __u8 *data);
 261 static void get_manufacturing_desc(struct edgeport_serial *edge_serial);
 262 static void get_boot_desc(struct edgeport_serial *edge_serial);
 263 static void load_application_firmware(struct edgeport_serial *edge_serial);
 264
 265 static void unicode_to_ascii(char *string, int buflen,
 266                                 __le16 *unicode, int unicode_size);
 267
 268
 269 /* ************************************************************************ */
 270 /* ************************************************************************ */
 271 /* ************************************************************************ */
 272 /* ************************************************************************ */
 273
 274 /************************************************************************
 275  *                                                                      *
 276  * update_edgeport_E2PROM()     Compare current versions of             *
 277  *                              Boot ROM and Manufacture                *
 278  *                              Descriptors with versions               *
 279  *                              embedded in this driver                 *
 280  *                                                                      *
 281  ************************************************************************/
 282 static void update_edgeport_E2PROM(struct edgeport_serial *edge_serial)
 283 {
 284         struct device *dev = &edge_serial->serial->dev->dev;
 285         __u32 BootCurVer;
 286         __u32 BootNewVer;
 287         __u8 BootMajorVersion;
 288         __u8 BootMinorVersion;
 289         __u16 BootBuildNumber;
 290         __u32 Bootaddr;
 291         const struct ihex_binrec *rec;
 292         const struct firmware *fw;
 293         const char *fw_name;
 294         int response;
 295
 296         switch (edge_serial->product_info.iDownloadFile) {
 297         case EDGE_DOWNLOAD_FILE_I930:
 298                 fw_name = "edgeport/boot.fw";
 299                 break;
 300         case EDGE_DOWNLOAD_FILE_80251:
 301                 fw_name = "edgeport/boot2.fw";
 302                 break;
 303         default:
 304                 return;
 305         }
 306
 307         response = request_ihex_firmware(&fw, fw_name,
 308                                          &edge_serial->serial->dev->dev);
 309         if (response) {
 310                 dev_err(dev, "Failed to load image \"%s\" err %d\n",
 311                        fw_name, response);
 312                 return;
 313         }
 314
 315         rec = (const struct ihex_binrec *)fw->data;
 316         BootMajorVersion = rec->data[0];
 317         BootMinorVersion = rec->data[1];
 318         BootBuildNumber = (rec->data[2] << 8) | rec->data[3];
 319
 320         /* Check Boot Image Version */
 321         BootCurVer = (edge_serial->boot_descriptor.MajorVersion << 24) +
 322                      (edge_serial->boot_descriptor.MinorVersion << 16) +
 323                       le16_to_cpu(edge_serial->boot_descriptor.BuildNumber);
 324
 325         BootNewVer = (BootMajorVersion << 24) +
 326                      (BootMinorVersion << 16) +
 327                       BootBuildNumber;
 328
 329         dev_dbg(dev, "Current Boot Image version %d.%d.%d\n",
 330             edge_serial->boot_descriptor.MajorVersion,
 331             edge_serial->boot_descriptor.MinorVersion,
 332             le16_to_cpu(edge_serial->boot_descriptor.BuildNumber));
 333
 334
 335         if (BootNewVer > BootCurVer) {
 336                 dev_dbg(dev, "**Update Boot Image from %d.%d.%d to %d.%d.%d\n",
 337                     edge_serial->boot_descriptor.MajorVersion,
 338                     edge_serial->boot_descriptor.MinorVersion,
 339                     le16_to_cpu(edge_serial->boot_descriptor.BuildNumber),
 340                     BootMajorVersion, BootMinorVersion, BootBuildNumber);
 341
 342                 dev_dbg(dev, "Downloading new Boot Image\n");
 343
 344                 for (rec = ihex_next_binrec(rec); rec;
 345                      rec = ihex_next_binrec(rec)) {
 346                         Bootaddr = be32_to_cpu(rec->addr);
 347                         response = rom_write(edge_serial->serial,
 348                                              Bootaddr >> 16,
 349                                              Bootaddr & 0xFFFF,
 350                                              be16_to_cpu(rec->len),
 351                                              &rec->data[0]);
 352                         if (response < 0) {
 353                                 dev_err(&edge_serial->serial->dev->dev,
 354                                         "rom_write failed (%x, %x, %d)\n",
 355                                         Bootaddr >> 16, Bootaddr & 0xFFFF,
 356                                         be16_to_cpu(rec->len));
 357                                 break;
 358                         }
 359                 }
 360         } else {
 361                 dev_dbg(dev, "Boot Image -- already up to date\n");
 362         }
 363         release_firmware(fw);
 364 }
 365
 366 #if 0
 367 /************************************************************************
 368  *
 369  *  Get string descriptor from device
 370  *
 371  ************************************************************************/
 372 static int get_string_desc(struct usb_device *dev, int Id,
 373                                 struct usb_string_descriptor **pRetDesc)
 374 {
 375         struct usb_string_descriptor StringDesc;
 376         struct usb_string_descriptor *pStringDesc;
 377
 378         dev_dbg(&dev->dev, "%s - USB String ID = %d\n", __func__, Id);
 379
 380         if (!usb_get_descriptor(dev, USB_DT_STRING, Id, &StringDesc,
 381                                                 sizeof(StringDesc)))
 382                 return 0;
 383
 384         pStringDesc = kmalloc(StringDesc.bLength, GFP_KERNEL);
 385         if (!pStringDesc)
 386                 return -1;
 387
 388         if (!usb_get_descriptor(dev, USB_DT_STRING, Id, pStringDesc,
 389                                                         StringDesc.bLength)) {
 390                 kfree(pStringDesc);
 391                 return -1;
 392         }
 393
 394         *pRetDesc = pStringDesc;
 395         return 0;
 396 }
 397 #endif
 398
 399 static void dump_product_info(struct edgeport_serial *edge_serial,
 400                               struct edgeport_product_info *product_info)
 401 {
 402         struct device *dev = &edge_serial->serial->dev->dev;
 403
 404         /* Dump Product Info structure */
 405         dev_dbg(dev, "**Product Information:\n");
 406         dev_dbg(dev, "  ProductId             %x\n", product_info->ProductId);
 407         dev_dbg(dev, "  NumPorts              %d\n", product_info->NumPorts);
 408         dev_dbg(dev, "  ProdInfoVer           %d\n", product_info->ProdInfoVer);
 409         dev_dbg(dev, "  IsServer              %d\n", product_info->IsServer);
 410         dev_dbg(dev, "  IsRS232               %d\n", product_info->IsRS232);
 411         dev_dbg(dev, "  IsRS422               %d\n", product_info->IsRS422);
 412         dev_dbg(dev, "  IsRS485               %d\n", product_info->IsRS485);
 413         dev_dbg(dev, "  RomSize               %d\n", product_info->RomSize);
 414         dev_dbg(dev, "  RamSize               %d\n", product_info->RamSize);
 415         dev_dbg(dev, "  CpuRev                %x\n", product_info->CpuRev);
 416         dev_dbg(dev, "  BoardRev              %x\n", product_info->BoardRev);
 417         dev_dbg(dev, "  BootMajorVersion      %d.%d.%d\n",
 418                 product_info->BootMajorVersion,
 419                 product_info->BootMinorVersion,
 420                 le16_to_cpu(product_info->BootBuildNumber));
 421         dev_dbg(dev, "  FirmwareMajorVersion  %d.%d.%d\n",
 422                 product_info->FirmwareMajorVersion,
 423                 product_info->FirmwareMinorVersion,
 424                 le16_to_cpu(product_info->FirmwareBuildNumber));
 425         dev_dbg(dev, "  ManufactureDescDate   %d/%d/%d\n",
 426                 product_info->ManufactureDescDate[0],
 427                 product_info->ManufactureDescDate[1],
 428                 product_info->ManufactureDescDate[2]+1900);
 429         dev_dbg(dev, "  iDownloadFile         0x%x\n",
 430                 product_info->iDownloadFile);
 431         dev_dbg(dev, "  EpicVer               %d\n", product_info->EpicVer);
 432 }
 433
 434 static void get_product_info(struct edgeport_serial *edge_serial)
 435 {
 436         struct edgeport_product_info *product_info = &edge_serial->product_info;
 437
 438         memset(product_info, 0, sizeof(struct edgeport_product_info));
 439
 440         product_info->ProductId = (__u16)(le16_to_cpu(edge_serial->serial->dev->descriptor.idProduct) & ~ION_DEVICE_ID_80251_NETCHIP);
 441         product_info->NumPorts = edge_serial->manuf_descriptor.NumPorts;
 442         product_info->ProdInfoVer = 0;
 443
 444         product_info->RomSize = edge_serial->manuf_descriptor.RomSize;
 445         product_info->RamSize = edge_serial->manuf_descriptor.RamSize;
 446         product_info->CpuRev = edge_serial->manuf_descriptor.CpuRev;
 447         product_info->BoardRev = edge_serial->manuf_descriptor.BoardRev;
 448
 449         product_info->BootMajorVersion =
 450                                 edge_serial->boot_descriptor.MajorVersion;
 451         product_info->BootMinorVersion =
 452                                 edge_serial->boot_descriptor.MinorVersion;
 453         product_info->BootBuildNumber =
 454                                 edge_serial->boot_descriptor.BuildNumber;
 455
 456         memcpy(product_info->ManufactureDescDate,
 457                         edge_serial->manuf_descriptor.DescDate,
 458                         sizeof(edge_serial->manuf_descriptor.DescDate));
 459
 460         /* check if this is 2nd generation hardware */
 461         if (le16_to_cpu(edge_serial->serial->dev->descriptor.idProduct)
 462                                             & ION_DEVICE_ID_80251_NETCHIP)
 463                 product_info->iDownloadFile = EDGE_DOWNLOAD_FILE_80251;
 464         else
 465                 product_info->iDownloadFile = EDGE_DOWNLOAD_FILE_I930;
 466
 467         /* Determine Product type and set appropriate flags */
 468         switch (DEVICE_ID_FROM_USB_PRODUCT_ID(product_info->ProductId)) {
 469         case ION_DEVICE_ID_EDGEPORT_COMPATIBLE:
 470         case ION_DEVICE_ID_EDGEPORT_4T:
 471         case ION_DEVICE_ID_EDGEPORT_4:
 472         case ION_DEVICE_ID_EDGEPORT_2:
 473         case ION_DEVICE_ID_EDGEPORT_8_DUAL_CPU:
 474         case ION_DEVICE_ID_EDGEPORT_8:
 475         case ION_DEVICE_ID_EDGEPORT_421:
 476         case ION_DEVICE_ID_EDGEPORT_21:
 477         case ION_DEVICE_ID_EDGEPORT_2_DIN:
 478         case ION_DEVICE_ID_EDGEPORT_4_DIN:
 479         case ION_DEVICE_ID_EDGEPORT_16_DUAL_CPU:
 480                 product_info->IsRS232 = 1;
 481                 break;
 482
 483         case ION_DEVICE_ID_EDGEPORT_2I: /* Edgeport/2 RS422/RS485 */
 484                 product_info->IsRS422 = 1;
 485                 product_info->IsRS485 = 1;
 486                 break;
 487
 488         case ION_DEVICE_ID_EDGEPORT_8I: /* Edgeport/4 RS422 */
 489         case ION_DEVICE_ID_EDGEPORT_4I: /* Edgeport/4 RS422 */
 490                 product_info->IsRS422 = 1;
 491                 break;
 492         }
 493
 494         dump_product_info(edge_serial, product_info);
 495 }
 496
 497 static int get_epic_descriptor(struct edgeport_serial *ep)
 498 {
 499         int result;
 500         struct usb_serial *serial = ep->serial;
 501         struct edgeport_product_info *product_info = &ep->product_info;
 502         struct edge_compatibility_descriptor *epic = &ep->epic_descriptor;
 503         struct edge_compatibility_bits *bits;
 504         struct device *dev = &serial->dev->dev;
 505
 506         ep->is_epic = 0;
 507         result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
 508                                  USB_REQUEST_ION_GET_EPIC_DESC,
 509                                  0xC0, 0x00, 0x00,
 510                                  &ep->epic_descriptor,
 511                                  sizeof(struct edge_compatibility_descriptor),
 512                                  300);
 513
 514         if (result > 0) {
 515                 ep->is_epic = 1;
 516                 memset(product_info, 0, sizeof(struct edgeport_product_info));
 517
 518                 product_info->NumPorts = epic->NumPorts;
 519                 product_info->ProdInfoVer = 0;
 520                 product_info->FirmwareMajorVersion = epic->MajorVersion;
 521                 product_info->FirmwareMinorVersion = epic->MinorVersion;
 522                 product_info->FirmwareBuildNumber = epic->BuildNumber;
 523                 product_info->iDownloadFile = epic->iDownloadFile;
 524                 product_info->EpicVer = epic->EpicVer;
 525                 product_info->Epic = epic->Supports;
 526                 product_info->ProductId = ION_DEVICE_ID_EDGEPORT_COMPATIBLE;
 527                 dump_product_info(ep, product_info);
 528
 529                 bits = &ep->epic_descriptor.Supports;
 530                 dev_dbg(dev, "**EPIC descriptor:\n");
 531                 dev_dbg(dev, "  VendEnableSuspend: %s\n", bits->VendEnableSuspend ? "TRUE": "FALSE");
 532                 dev_dbg(dev, "  IOSPOpen         : %s\n", bits->IOSPOpen        ? "TRUE": "FALSE");
 533                 dev_dbg(dev, "  IOSPClose        : %s\n", bits->IOSPClose       ? "TRUE": "FALSE");
 534                 dev_dbg(dev, "  IOSPChase        : %s\n", bits->IOSPChase       ? "TRUE": "FALSE");
 535                 dev_dbg(dev, "  IOSPSetRxFlow    : %s\n", bits->IOSPSetRxFlow   ? "TRUE": "FALSE");
 536                 dev_dbg(dev, "  IOSPSetTxFlow    : %s\n", bits->IOSPSetTxFlow   ? "TRUE": "FALSE");
 537                 dev_dbg(dev, "  IOSPSetXChar     : %s\n", bits->IOSPSetXChar    ? "TRUE": "FALSE");
 538                 dev_dbg(dev, "  IOSPRxCheck      : %s\n", bits->IOSPRxCheck     ? "TRUE": "FALSE");
 539                 dev_dbg(dev, "  IOSPSetClrBreak  : %s\n", bits->IOSPSetClrBreak ? "TRUE": "FALSE");
 540                 dev_dbg(dev, "  IOSPWriteMCR     : %s\n", bits->IOSPWriteMCR    ? "TRUE": "FALSE");
 541                 dev_dbg(dev, "  IOSPWriteLCR     : %s\n", bits->IOSPWriteLCR    ? "TRUE": "FALSE");
 542                 dev_dbg(dev, "  IOSPSetBaudRate  : %s\n", bits->IOSPSetBaudRate ? "TRUE": "FALSE");
 543                 dev_dbg(dev, "  TrueEdgeport     : %s\n", bits->TrueEdgeport    ? "TRUE": "FALSE");
 544         }
 545
 546         return result;
 547 }
 548
 549
 550 /************************************************************************/
 551 /************************************************************************/
 552 /*            U S B  C A L L B A C K   F U N C T I O N S                */
 553 /*            U S B  C A L L B A C K   F U N C T I O N S                */
 554 /************************************************************************/
 555 /************************************************************************/
 556
 557 /*****************************************************************************
 558  * edge_interrupt_callback
 559  *      this is the callback function for when we have received data on the
 560  *      interrupt endpoint.
 561  *****************************************************************************/
 562 static void edge_interrupt_callback(struct urb *urb)
 563 {
 564         struct edgeport_serial *edge_serial = urb->context;
 565         struct device *dev;
 566         struct edgeport_port *edge_port;
 567         struct usb_serial_port *port;
 568         struct tty_struct *tty;
 569         unsigned char *data = urb->transfer_buffer;
 570         int length = urb->actual_length;
 571         int bytes_avail;
 572         int position;
 573         int txCredits;
 574         int portNumber;
 575         int result;
 576         int status = urb->status;
 577
 578         switch (status) {
 579         case 0:
 580                 /* success */
 581                 break;
 582         case -ECONNRESET:
 583         case -ENOENT:
 584         case -ESHUTDOWN:
 585                 /* this urb is terminated, clean up */
 586                 dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n", __func__, status);
 587                 return;
 588         default:
 589                 dev_dbg(&urb->dev->dev, "%s - nonzero urb status received: %d\n", __func__, status);
 590                 goto exit;
 591         }
 592
 593         dev = &edge_serial->serial->dev->dev;
 594
 595         /* process this interrupt-read even if there are no ports open */
 596         if (length) {
 597                 usb_serial_debug_data(dev, __func__, length, data);
 598
 599                 if (length > 1) {
 600                         bytes_avail = data[0] | (data[1] << 8);
 601                         if (bytes_avail) {
 602                                 spin_lock(&edge_serial->es_lock);
 603                                 edge_serial->rxBytesAvail += bytes_avail;
 604                                 dev_dbg(dev,
 605                                         "%s - bytes_avail=%d, rxBytesAvail=%d, read_in_progress=%d\n",
 606                                         __func__, bytes_avail,
 607                                         edge_serial->rxBytesAvail,
 608                                         edge_serial->read_in_progress);
 609
 610                                 if (edge_serial->rxBytesAvail > 0 &&
 611                                     !edge_serial->read_in_progress) {
 612                                         dev_dbg(dev, "%s - posting a read\n", __func__);
 613                                         edge_serial->read_in_progress = true;
 614
 615                                         /* we have pending bytes on the
 616                                            bulk in pipe, send a request */
 617                                         result = usb_submit_urb(edge_serial->read_urb, GFP_ATOMIC);
 618                                         if (result) {
 619                                                 dev_err(dev,
 620                                                         "%s - usb_submit_urb(read bulk) failed with result = %d\n",
 621                                                         __func__, result);
 622                                                 edge_serial->read_in_progress = false;
 623                                         }
 624                                 }
 625                                 spin_unlock(&edge_serial->es_lock);
 626                         }
 627                 }
 628                 /* grab the txcredits for the ports if available */
 629                 position = 2;
 630                 portNumber = 0;
 631                 while ((position < length) &&
 632                                 (portNumber < edge_serial->serial->num_ports)) {
 633                         txCredits = data[position] | (data[position+1] << 8);
 634                         if (txCredits) {
 635                                 port = edge_serial->serial->port[portNumber];
 636                                 edge_port = usb_get_serial_port_data(port);
 637                                 if (edge_port->open) {
 638                                         spin_lock(&edge_port->ep_lock);
 639                                         edge_port->txCredits += txCredits;
 640                                         spin_unlock(&edge_port->ep_lock);
 641                                         dev_dbg(dev, "%s - txcredits for port%d = %d\n",
 642                                                 __func__, portNumber,
 643                                                 edge_port->txCredits);
 644
 645                                         /* tell the tty driver that something
 646                                            has changed */
 647                                         tty = tty_port_tty_get(
 648                                                 &edge_port->port->port);
 649                                         if (tty) {
 650                                                 tty_wakeup(tty);
 651                                                 tty_kref_put(tty);
 652                                         }
 653                                         /* Since we have more credit, check
 654                                            if more data can be sent */
 655                                         send_more_port_data(edge_serial,
 656                                                                 edge_port);
 657                                 }
 658                         }
 659                         position += 2;
 660                         ++portNumber;
 661                 }
 662         }
 663
 664 exit:
 665         result = usb_submit_urb(urb, GFP_ATOMIC);
 666         if (result)
 667                 dev_err(&urb->dev->dev,
 668                         "%s - Error %d submitting control urb\n",
 669                                                 __func__, result);
 670 }
 671
 672
 673 /*****************************************************************************
 674  * edge_bulk_in_callback
 675  *      this is the callback function for when we have received data on the
 676  *      bulk in endpoint.
 677  *****************************************************************************/
 678 static void edge_bulk_in_callback(struct urb *urb)
 679 {
 680         struct edgeport_serial  *edge_serial = urb->context;
 681         struct device *dev;
 682         unsigned char           *data = urb->transfer_buffer;
 683         int                     retval;
 684         __u16                   raw_data_length;
 685         int status = urb->status;
 686
 687         if (status) {
 688                 dev_dbg(&urb->dev->dev, "%s - nonzero read bulk status received: %d\n",
 689                         __func__, status);
 690                 edge_serial->read_in_progress = false;
 691                 return;
 692         }
 693
 694         if (urb->actual_length == 0) {
 695                 dev_dbg(&urb->dev->dev, "%s - read bulk callback with no data\n", __func__);
 696                 edge_serial->read_in_progress = false;
 697                 return;
 698         }
 699
 700         dev = &edge_serial->serial->dev->dev;
 701         raw_data_length = urb->actual_length;
 702
 703         usb_serial_debug_data(dev, __func__, raw_data_length, data);
 704
 705         spin_lock(&edge_serial->es_lock);
 706
 707         /* decrement our rxBytes available by the number that we just got */
 708         edge_serial->rxBytesAvail -= raw_data_length;
 709
 710         dev_dbg(dev, "%s - Received = %d, rxBytesAvail %d\n", __func__,
 711                 raw_data_length, edge_serial->rxBytesAvail);
 712
 713         process_rcvd_data(edge_serial, data, urb->actual_length);
 714
 715         /* check to see if there's any more data for us to read */
 716         if (edge_serial->rxBytesAvail > 0) {
 717                 dev_dbg(dev, "%s - posting a read\n", __func__);
 718                 retval = usb_submit_urb(edge_serial->read_urb, GFP_ATOMIC);
 719                 if (retval) {
 720                         dev_err(dev,
 721                                 "%s - usb_submit_urb(read bulk) failed, retval = %d\n",
 722                                 __func__, retval);
 723                         edge_serial->read_in_progress = false;
 724                 }
 725         } else {
 726                 edge_serial->read_in_progress = false;
 727         }
 728
 729         spin_unlock(&edge_serial->es_lock);
 730 }
 731
 732
 733 /*****************************************************************************
 734  * edge_bulk_out_data_callback
 735  *      this is the callback function for when we have finished sending
 736  *      serial data on the bulk out endpoint.
 737  *****************************************************************************/
 738 static void edge_bulk_out_data_callback(struct urb *urb)
 739 {
 740         struct edgeport_port *edge_port = urb->context;
 741         struct tty_struct *tty;
 742         int status = urb->status;
 743
 744         if (status) {
 745                 dev_dbg(&urb->dev->dev,
 746                         "%s - nonzero write bulk status received: %d\n",
 747                         __func__, status);
 748         }
 749
 750         tty = tty_port_tty_get(&edge_port->port->port);
 751
 752         if (tty && edge_port->open) {
 753                 /* let the tty driver wakeup if it has a special
 754                    write_wakeup function */
 755                 tty_wakeup(tty);
 756         }
 757         tty_kref_put(tty);
 758
 759         /* Release the Write URB */
 760         edge_port->write_in_progress = false;
 761
 762         /* Check if more data needs to be sent */
 763         send_more_port_data((struct edgeport_serial *)
 764                 (usb_get_serial_data(edge_port->port->serial)), edge_port);
 765 }
 766
 767
 768 /*****************************************************************************
 769  * BulkOutCmdCallback
 770  *      this is the callback function for when we have finished sending a
 771  *      command on the bulk out endpoint.
 772  *****************************************************************************/
 773 static void edge_bulk_out_cmd_callback(struct urb *urb)
 774 {
 775         struct edgeport_port *edge_port = urb->context;
 776         struct tty_struct *tty;
 777         int status = urb->status;
 778
 779         atomic_dec(&CmdUrbs);
 780         dev_dbg(&urb->dev->dev, "%s - FREE URB %p (outstanding %d)\n",
 781                 __func__, urb, atomic_read(&CmdUrbs));
 782
 783
 784         /* clean up the transfer buffer */
 785         kfree(urb->transfer_buffer);
 786
 787         /* Free the command urb */
 788         usb_free_urb(urb);
 789
 790         if (status) {
 791                 dev_dbg(&urb->dev->dev,
 792                         "%s - nonzero write bulk status received: %d\n",
 793                         __func__, status);
 794                 return;
 795         }
 796
 797         /* Get pointer to tty */
 798         tty = tty_port_tty_get(&edge_port->port->port);
 799
 800         /* tell the tty driver that something has changed */
 801         if (tty && edge_port->open)
 802                 tty_wakeup(tty);
 803         tty_kref_put(tty);
 804
 805         /* we have completed the command */
 806         edge_port->commandPending = false;
 807         wake_up(&edge_port->wait_command);
 808 }
 809
 810
 811 /*****************************************************************************
 812  * Driver tty interface functions
 813  *****************************************************************************/
 814
 815 /*****************************************************************************
 816  * SerialOpen
 817  *      this function is called by the tty driver when a port is opened
 818  *      If successful, we return 0
 819  *      Otherwise we return a negative error number.
 820  *****************************************************************************/
 821 static int edge_open(struct tty_struct *tty, struct usb_serial_port *port)
 822 {
 823         struct edgeport_port *edge_port = usb_get_serial_port_data(port);
 824         struct device *dev = &port->dev;
 825         struct usb_serial *serial;
 826         struct edgeport_serial *edge_serial;
 827         int response;
 828
 829         if (edge_port == NULL)
 830                 return -ENODEV;
 831
 832         /* see if we've set up our endpoint info yet (can't set it up
 833            in edge_startup as the structures were not set up at that time.) */
 834         serial = port->serial;
 835         edge_serial = usb_get_serial_data(serial);
 836         if (edge_serial == NULL)
 837                 return -ENODEV;
 838         if (edge_serial->interrupt_in_buffer == NULL) {
 839                 struct usb_serial_port *port0 = serial->port[0];
 840
 841                 /* not set up yet, so do it now */
 842                 edge_serial->interrupt_in_buffer =
 843                                         port0->interrupt_in_buffer;
 844                 edge_serial->interrupt_in_endpoint =
 845                                         port0->interrupt_in_endpointAddress;
 846                 edge_serial->interrupt_read_urb = port0->interrupt_in_urb;
 847                 edge_serial->bulk_in_buffer = port0->bulk_in_buffer;
 848                 edge_serial->bulk_in_endpoint =
 849                                         port0->bulk_in_endpointAddress;
 850                 edge_serial->read_urb = port0->read_urb;
 851                 edge_serial->bulk_out_endpoint =
 852                                         port0->bulk_out_endpointAddress;
 853
 854                 /* set up our interrupt urb */
 855                 usb_fill_int_urb(edge_serial->interrupt_read_urb,
 856                       serial->dev,
 857                       usb_rcvintpipe(serial->dev,
 858                                 port0->interrupt_in_endpointAddress),
 859                       port0->interrupt_in_buffer,
 860                       edge_serial->interrupt_read_urb->transfer_buffer_length,
 861                       edge_interrupt_callback, edge_serial,
 862                       edge_serial->interrupt_read_urb->interval);
 863
 864                 /* set up our bulk in urb */
 865                 usb_fill_bulk_urb(edge_serial->read_urb, serial->dev,
 866                         usb_rcvbulkpipe(serial->dev,
 867                                 port0->bulk_in_endpointAddress),
 868                         port0->bulk_in_buffer,
 869                         edge_serial->read_urb->transfer_buffer_length,
 870                         edge_bulk_in_callback, edge_serial);
 871                 edge_serial->read_in_progress = false;
 872
 873                 /* start interrupt read for this edgeport
 874                  * this interrupt will continue as long
 875                  * as the edgeport is connected */
 876                 response = usb_submit_urb(edge_serial->interrupt_read_urb,
 877                                                                 GFP_KERNEL);
 878                 if (response) {
 879                         dev_err(dev, "%s - Error %d submitting control urb\n",
 880                                 __func__, response);
 881                 }
 882         }
 883
 884         /* initialize our wait queues */
 885         init_waitqueue_head(&edge_port->wait_open);
 886         init_waitqueue_head(&edge_port->wait_chase);
 887         init_waitqueue_head(&edge_port->delta_msr_wait);
 888         init_waitqueue_head(&edge_port->wait_command);
 889
 890         /* initialize our icount structure */
 891         memset(&(edge_port->icount), 0x00, sizeof(edge_port->icount));
 892
 893         /* initialize our port settings */
 894         edge_port->txCredits = 0;       /* Can't send any data yet */
 895         /* Must always set this bit to enable ints! */
 896         edge_port->shadowMCR = MCR_MASTER_IE;
 897         edge_port->chaseResponsePending = false;
 898
 899         /* send a open port command */
 900         edge_port->openPending = true;
 901         edge_port->open        = false;
 902         response = send_iosp_ext_cmd(edge_port, IOSP_CMD_OPEN_PORT, 0);
 903
 904         if (response < 0) {
 905                 dev_err(dev, "%s - error sending open port command\n", __func__);
 906                 edge_port->openPending = false;
 907                 return -ENODEV;
 908         }
 909
 910         /* now wait for the port to be completely opened */
 911         wait_event_timeout(edge_port->wait_open, !edge_port->openPending,
 912                                                                 OPEN_TIMEOUT);
 913
 914         if (!edge_port->open) {
 915                 /* open timed out */
 916                 dev_dbg(dev, "%s - open timedout\n", __func__);
 917                 edge_port->openPending = false;
 918                 return -ENODEV;
 919         }
 920
 921         /* create the txfifo */
 922         edge_port->txfifo.head  = 0;
 923         edge_port->txfifo.tail  = 0;
 924         edge_port->txfifo.count = 0;
 925         edge_port->txfifo.size  = edge_port->maxTxCredits;
 926         edge_port->txfifo.fifo  = kmalloc(edge_port->maxTxCredits, GFP_KERNEL);
 927
 928         if (!edge_port->txfifo.fifo) {
 929                 dev_dbg(dev, "%s - no memory\n", __func__);
 930                 edge_close(port);
 931                 return -ENOMEM;
 932         }
 933
 934         /* Allocate a URB for the write */
 935         edge_port->write_urb = usb_alloc_urb(0, GFP_KERNEL);
 936         edge_port->write_in_progress = false;
 937
 938         if (!edge_port->write_urb) {
 939                 dev_dbg(dev, "%s - no memory\n", __func__);
 940                 edge_close(port);
 941                 return -ENOMEM;
 942         }
 943
 944         dev_dbg(dev, "%s(%d) - Initialize TX fifo to %d bytes\n",
 945                 __func__, port->number, edge_port->maxTxCredits);
 946
 947         return 0;
 948 }
 949
 950
 951 /************************************************************************
 952  *
 953  * block_until_chase_response
 954  *
 955  *      This function will block the close until one of the following:
 956  *              1. Response to our Chase comes from Edgeport
 957  *              2. A timeout of 10 seconds without activity has expired
 958  *                 (1K of Edgeport data @ 2400 baud ==> 4 sec to empty)
 959  *
 960  ************************************************************************/
 961 static void block_until_chase_response(struct edgeport_port *edge_port)
 962 {
 963         struct device *dev = &edge_port->port->dev;
 964         DEFINE_WAIT(wait);
 965         __u16 lastCredits;
 966         int timeout = 1*HZ;
 967         int loop = 10;
 968
 969         while (1) {
 970                 /* Save Last credits */
 971                 lastCredits = edge_port->txCredits;
 972
 973                 /* Did we get our Chase response */
 974                 if (!edge_port->chaseResponsePending) {
 975                         dev_dbg(dev, "%s - Got Chase Response\n", __func__);
 976
 977                         /* did we get all of our credit back? */
 978                         if (edge_port->txCredits == edge_port->maxTxCredits) {
 979                                 dev_dbg(dev, "%s - Got all credits\n", __func__);
 980                                 return;
 981                         }
 982                 }
 983
 984                 /* Block the thread for a while */
 985                 prepare_to_wait(&edge_port->wait_chase, &wait,
 986                                                 TASK_UNINTERRUPTIBLE);
 987                 schedule_timeout(timeout);
 988                 finish_wait(&edge_port->wait_chase, &wait);
 989
 990                 if (lastCredits == edge_port->txCredits) {
 991                         /* No activity.. count down. */
 992                         loop--;
 993                         if (loop == 0) {
 994                                 edge_port->chaseResponsePending = false;
 995                                 dev_dbg(dev, "%s - Chase TIMEOUT\n", __func__);
 996                                 return;
 997                         }
 998                 } else {
 999                         /* Reset timeout value back to 10 seconds */
1000                         dev_dbg(dev, "%s - Last %d, Current %d\n", __func__,
1001                                         lastCredits, edge_port->txCredits);
1002                         loop = 10;
1003                 }
1004         }
1005 }
1006
1007
1008 /************************************************************************
1009  *
1010  * block_until_tx_empty
1011  *
1012  *      This function will block the close until one of the following:
1013  *              1. TX count are 0
1014  *              2. The edgeport has stopped
1015  *              3. A timeout of 3 seconds without activity has expired
1016  *
1017  ************************************************************************/
1018 static void block_until_tx_empty(struct edgeport_port *edge_port)
1019 {
1020         struct device *dev = &edge_port->port->dev;
1021         DEFINE_WAIT(wait);
1022         struct TxFifo *fifo = &edge_port->txfifo;
1023         __u32 lastCount;
1024         int timeout = HZ/10;
1025         int loop = 30;
1026
1027         while (1) {
1028                 /* Save Last count */
1029                 lastCount = fifo->count;
1030
1031                 /* Is the Edgeport Buffer empty? */
1032                 if (lastCount == 0) {
1033                         dev_dbg(dev, "%s - TX Buffer Empty\n", __func__);
1034                         return;
1035                 }
1036
1037                 /* Block the thread for a while */
1038                 prepare_to_wait(&edge_port->wait_chase, &wait,
1039                                                 TASK_UNINTERRUPTIBLE);
1040                 schedule_timeout(timeout);
1041                 finish_wait(&edge_port->wait_chase, &wait);
1042
1043                 dev_dbg(dev, "%s wait\n", __func__);
1044
1045                 if (lastCount == fifo->count) {
1046                         /* No activity.. count down. */
1047                         loop--;
1048                         if (loop == 0) {
1049                                 dev_dbg(dev, "%s - TIMEOUT\n", __func__);
1050                                 return;
1051                         }
1052                 } else {
1053                         /* Reset timeout value back to seconds */
1054                         loop = 30;
1055                 }
1056         }
1057 }
1058
1059
1060 /*****************************************************************************
1061  * edge_close
1062  *      this function is called by the tty driver when a port is closed
1063  *****************************************************************************/
1064 static void edge_close(struct usb_serial_port *port)
1065 {
1066         struct edgeport_serial *edge_serial;
1067         struct edgeport_port *edge_port;
1068         int status;
1069
1070         edge_serial = usb_get_serial_data(port->serial);
1071         edge_port = usb_get_serial_port_data(port);
1072         if (edge_serial == NULL || edge_port == NULL)
1073                 return;
1074
1075         /* block until tx is empty */
1076         block_until_tx_empty(edge_port);
1077
1078         edge_port->closePending = true;
1079
1080         if ((!edge_serial->is_epic) ||
1081             ((edge_serial->is_epic) &&
1082              (edge_serial->epic_descriptor.Supports.IOSPChase))) {
1083                 /* flush and chase */
1084                 edge_port->chaseResponsePending = true;
1085
1086                 dev_dbg(&port->dev, "%s - Sending IOSP_CMD_CHASE_PORT\n", __func__);
1087                 status = send_iosp_ext_cmd(edge_port, IOSP_CMD_CHASE_PORT, 0);
1088                 if (status == 0)
1089                         /* block until chase finished */
1090                         block_until_chase_response(edge_port);
1091                 else
1092                         edge_port->chaseResponsePending = false;
1093         }
1094
1095         if ((!edge_serial->is_epic) ||
1096             ((edge_serial->is_epic) &&
1097              (edge_serial->epic_descriptor.Supports.IOSPClose))) {
1098                /* close the port */
1099                 dev_dbg(&port->dev, "%s - Sending IOSP_CMD_CLOSE_PORT\n", __func__);
1100                 send_iosp_ext_cmd(edge_port, IOSP_CMD_CLOSE_PORT, 0);
1101         }
1102
1103         /* port->close = true; */
1104         edge_port->closePending = false;
1105         edge_port->open = false;
1106         edge_port->openPending = false;
1107
1108         usb_kill_urb(edge_port->write_urb);
1109
1110         if (edge_port->write_urb) {
1111                 /* if this urb had a transfer buffer already
1112                                 (old transfer) free it */
1113                 kfree(edge_port->write_urb->transfer_buffer);
1114                 usb_free_urb(edge_port->write_urb);
1115                 edge_port->write_urb = NULL;
1116         }
1117         kfree(edge_port->txfifo.fifo);
1118         edge_port->txfifo.fifo = NULL;
1119 }
1120
1121 /*****************************************************************************
1122  * SerialWrite
1123  *      this function is called by the tty driver when data should be written
1124  *      to the port.
1125  *      If successful, we return the number of bytes written, otherwise we
1126  *      return a negative error number.
1127  *****************************************************************************/
1128 static int edge_write(struct tty_struct *tty, struct usb_serial_port *port,
1129                                         const unsigned char *data, int count)
1130 {
1131         struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1132         struct TxFifo *fifo;
1133         int copySize;
1134         int bytesleft;
1135         int firsthalf;
1136         int secondhalf;
1137         unsigned long flags;
1138
1139         if (edge_port == NULL)
1140                 return -ENODEV;
1141
1142         /* get a pointer to the Tx fifo */
1143         fifo = &edge_port->txfifo;
1144
1145         spin_lock_irqsave(&edge_port->ep_lock, flags);
1146
1147         /* calculate number of bytes to put in fifo */
1148         copySize = min((unsigned int)count,
1149                                 (edge_port->txCredits - fifo->count));
1150
1151         dev_dbg(&port->dev, "%s(%d) of %d byte(s) Fifo room  %d -- will copy %d bytes\n",
1152                 __func__, port->number, count,
1153                         edge_port->txCredits - fifo->count, copySize);
1154
1155         /* catch writes of 0 bytes which the tty driver likes to give us,
1156            and when txCredits is empty */
1157         if (copySize == 0) {
1158                 dev_dbg(&port->dev, "%s - copySize = Zero\n", __func__);
1159                 goto finish_write;
1160         }
1161
1162         /* queue the data
1163          * since we can never overflow the buffer we do not have to check for a
1164          * full condition
1165          *
1166          * the copy is done is two parts -- first fill to the end of the buffer
1167          * then copy the reset from the start of the buffer
1168          */
1169         bytesleft = fifo->size - fifo->head;
1170         firsthalf = min(bytesleft, copySize);
1171         dev_dbg(&port->dev, "%s - copy %d bytes of %d into fifo \n", __func__,
1172                 firsthalf, bytesleft);
1173
1174         /* now copy our data */
1175         memcpy(&fifo->fifo[fifo->head], data, firsthalf);
1176         usb_serial_debug_data(&port->dev, __func__, firsthalf, &fifo->fifo[fifo->head]);
1177
1178         /* update the index and size */
1179         fifo->head  += firsthalf;
1180         fifo->count += firsthalf;
1181
1182         /* wrap the index */
1183         if (fifo->head == fifo->size)
1184                 fifo->head = 0;
1185
1186         secondhalf = copySize-firsthalf;
1187
1188         if (secondhalf) {
1189                 dev_dbg(&port->dev, "%s - copy rest of data %d\n", __func__, secondhalf);
1190                 memcpy(&fifo->fifo[fifo->head], &data[firsthalf], secondhalf);
1191                 usb_serial_debug_data(&port->dev, __func__, secondhalf, &fifo->fifo[fifo->head]);
1192                 /* update the index and size */
1193                 fifo->count += secondhalf;
1194                 fifo->head  += secondhalf;
1195                 /* No need to check for wrap since we can not get to end of
1196                  * the fifo in this part
1197                  */
1198         }
1199
1200 finish_write:
1201         spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1202
1203         send_more_port_data((struct edgeport_serial *)
1204                         usb_get_serial_data(port->serial), edge_port);
1205
1206         dev_dbg(&port->dev, "%s wrote %d byte(s) TxCredits %d, Fifo %d\n",
1207                 __func__, copySize, edge_port->txCredits, fifo->count);
1208
1209         return copySize;
1210 }
1211
1212
1213 /************************************************************************
1214  *
1215  * send_more_port_data()
1216  *
1217  *      This routine attempts to write additional UART transmit data
1218  *      to a port over the USB bulk pipe. It is called (1) when new
1219  *      data has been written to a port's TxBuffer from higher layers
1220  *      (2) when the peripheral sends us additional TxCredits indicating
1221  *      that it can accept more Tx data for a given port; and (3) when
1222  *      a bulk write completes successfully and we want to see if we
1223  *      can transmit more.
1224  *
1225  ************************************************************************/
1226 static void send_more_port_data(struct edgeport_serial *edge_serial,
1227                                         struct edgeport_port *edge_port)
1228 {
1229         struct TxFifo   *fifo = &edge_port->txfifo;
1230         struct device   *dev = &edge_port->port->dev;
1231         struct urb      *urb;
1232         unsigned char   *buffer;
1233         int             status;
1234         int             count;
1235         int             bytesleft;
1236         int             firsthalf;
1237         int             secondhalf;
1238         unsigned long   flags;
1239
1240         spin_lock_irqsave(&edge_port->ep_lock, flags);
1241
1242         if (edge_port->write_in_progress ||
1243             !edge_port->open             ||
1244             (fifo->count == 0)) {
1245                 dev_dbg(dev, "%s(%d) EXIT - fifo %d, PendingWrite = %d\n",
1246                         __func__, edge_port->port->number,
1247                         fifo->count, edge_port->write_in_progress);
1248                 goto exit_send;
1249         }
1250
1251         /* since the amount of data in the fifo will always fit into the
1252          * edgeport buffer we do not need to check the write length
1253          *
1254          * Do we have enough credits for this port to make it worthwhile
1255          * to bother queueing a write. If it's too small, say a few bytes,
1256          * it's better to wait for more credits so we can do a larger write.
1257          */
1258         if (edge_port->txCredits < EDGE_FW_GET_TX_CREDITS_SEND_THRESHOLD(edge_port->maxTxCredits, EDGE_FW_BULK_MAX_PACKET_SIZE)) {
1259                 dev_dbg(dev, "%s(%d) Not enough credit - fifo %d TxCredit %d\n",
1260                         __func__, edge_port->port->number, fifo->count,
1261                         edge_port->txCredits);
1262                 goto exit_send;
1263         }
1264
1265         /* lock this write */
1266         edge_port->write_in_progress = true;
1267
1268         /* get a pointer to the write_urb */
1269         urb = edge_port->write_urb;
1270
1271         /* make sure transfer buffer is freed */
1272         kfree(urb->transfer_buffer);
1273         urb->transfer_buffer = NULL;
1274
1275         /* build the data header for the buffer and port that we are about
1276            to send out */
1277         count = fifo->count;
1278         buffer = kmalloc(count+2, GFP_ATOMIC);
1279         if (buffer == NULL) {
1280                 dev_err_console(edge_port->port,
1281                                 "%s - no more kernel memory...\n", __func__);
1282                 edge_port->write_in_progress = false;
1283                 goto exit_send;
1284         }
1285         buffer[0] = IOSP_BUILD_DATA_HDR1(edge_port->port->number
1286                                 - edge_port->port->serial->minor, count);
1287         buffer[1] = IOSP_BUILD_DATA_HDR2(edge_port->port->number
1288                                 - edge_port->port->serial->minor, count);
1289
1290         /* now copy our data */
1291         bytesleft =  fifo->size - fifo->tail;
1292         firsthalf = min(bytesleft, count);
1293         memcpy(&buffer[2], &fifo->fifo[fifo->tail], firsthalf);
1294         fifo->tail  += firsthalf;
1295         fifo->count -= firsthalf;
1296         if (fifo->tail == fifo->size)
1297                 fifo->tail = 0;
1298
1299         secondhalf = count-firsthalf;
1300         if (secondhalf) {
1301                 memcpy(&buffer[2+firsthalf], &fifo->fifo[fifo->tail],
1302                                                                 secondhalf);
1303                 fifo->tail  += secondhalf;
1304                 fifo->count -= secondhalf;
1305         }
1306
1307         if (count)
1308                 usb_serial_debug_data(&edge_port->port->dev, __func__, count, &buffer[2]);
1309
1310         /* fill up the urb with all of our data and submit it */
1311         usb_fill_bulk_urb(urb, edge_serial->serial->dev,
1312                         usb_sndbulkpipe(edge_serial->serial->dev,
1313                                         edge_serial->bulk_out_endpoint),
1314                         buffer, count+2,
1315                         edge_bulk_out_data_callback, edge_port);
1316
1317         /* decrement the number of credits we have by the number we just sent */
1318         edge_port->txCredits -= count;
1319         edge_port->icount.tx += count;
1320
1321         status = usb_submit_urb(urb, GFP_ATOMIC);
1322         if (status) {
1323                 /* something went wrong */
1324                 dev_err_console(edge_port->port,
1325                         "%s - usb_submit_urb(write bulk) failed, status = %d, data lost\n",
1326                                 __func__, status);
1327                 edge_port->write_in_progress = false;
1328
1329                 /* revert the credits as something bad happened. */
1330                 edge_port->txCredits += count;
1331                 edge_port->icount.tx -= count;
1332         }
1333         dev_dbg(dev, "%s wrote %d byte(s) TxCredit %d, Fifo %d\n",
1334                 __func__, count, edge_port->txCredits, fifo->count);
1335
1336 exit_send:
1337         spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1338 }
1339
1340
1341 /*****************************************************************************
1342  * edge_write_room
1343  *      this function is called by the tty driver when it wants to know how
1344  *      many bytes of data we can accept for a specific port. If successful,
1345  *      we return the amount of room that we have for this port (the txCredits)
1346  *      otherwise we return a negative error number.
1347  *****************************************************************************/
1348 static int edge_write_room(struct tty_struct *tty)
1349 {
1350         struct usb_serial_port *port = tty->driver_data;
1351         struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1352         int room;
1353         unsigned long flags;
1354
1355         if (edge_port == NULL)
1356                 return 0;
1357         if (edge_port->closePending)
1358                 return 0;
1359
1360         if (!edge_port->open) {
1361                 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1362                 return 0;
1363         }
1364
1365         /* total of both buffers is still txCredit */
1366         spin_lock_irqsave(&edge_port->ep_lock, flags);
1367         room = edge_port->txCredits - edge_port->txfifo.count;
1368         spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1369
1370         dev_dbg(&port->dev, "%s - returns %d\n", __func__, room);
1371         return room;
1372 }
1373
1374
1375 /*****************************************************************************
1376  * edge_chars_in_buffer
1377  *      this function is called by the tty driver when it wants to know how
1378  *      many bytes of data we currently have outstanding in the port (data that
1379  *      has been written, but hasn't made it out the port yet)
1380  *      If successful, we return the number of bytes left to be written in the
1381  *      system,
1382  *      Otherwise we return a negative error number.
1383  *****************************************************************************/
1384 static int edge_chars_in_buffer(struct tty_struct *tty)
1385 {
1386         struct usb_serial_port *port = tty->driver_data;
1387         struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1388         int num_chars;
1389         unsigned long flags;
1390
1391         if (edge_port == NULL)
1392                 return 0;
1393         if (edge_port->closePending)
1394                 return 0;
1395
1396         if (!edge_port->open) {
1397                 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1398                 return 0;
1399         }
1400
1401         spin_lock_irqsave(&edge_port->ep_lock, flags);
1402         num_chars = edge_port->maxTxCredits - edge_port->txCredits +
1403                                                 edge_port->txfifo.count;
1404         spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1405         if (num_chars) {
1406                 dev_dbg(&port->dev, "%s(port %d) - returns %d\n", __func__,
1407                         port->number, num_chars);
1408         }
1409
1410         return num_chars;
1411 }
1412
1413
1414 /*****************************************************************************
1415  * SerialThrottle
1416  *      this function is called by the tty driver when it wants to stop the data
1417  *      being read from the port.
1418  *****************************************************************************/
1419 static void edge_throttle(struct tty_struct *tty)
1420 {
1421         struct usb_serial_port *port = tty->driver_data;
1422         struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1423         int status;
1424
1425         if (edge_port == NULL)
1426                 return;
1427
1428         if (!edge_port->open) {
1429                 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1430                 return;
1431         }
1432
1433         /* if we are implementing XON/XOFF, send the stop character */
1434         if (I_IXOFF(tty)) {
1435                 unsigned char stop_char = STOP_CHAR(tty);
1436                 status = edge_write(tty, port, &stop_char, 1);
1437                 if (status <= 0)
1438                         return;
1439         }
1440
1441         /* if we are implementing RTS/CTS, toggle that line */
1442         if (tty->termios.c_cflag & CRTSCTS) {
1443                 edge_port->shadowMCR &= ~MCR_RTS;
1444                 status = send_cmd_write_uart_register(edge_port, MCR,
1445                                                         edge_port->shadowMCR);
1446                 if (status != 0)
1447                         return;
1448         }
1449 }
1450
1451
1452 /*****************************************************************************
1453  * edge_unthrottle
1454  *      this function is called by the tty driver when it wants to resume the
1455  *      data being read from the port (called after SerialThrottle is called)
1456  *****************************************************************************/
1457 static void edge_unthrottle(struct tty_struct *tty)
1458 {
1459         struct usb_serial_port *port = tty->driver_data;
1460         struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1461         int status;
1462
1463         if (edge_port == NULL)
1464                 return;
1465
1466         if (!edge_port->open) {
1467                 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1468                 return;
1469         }
1470
1471         /* if we are implementing XON/XOFF, send the start character */
1472         if (I_IXOFF(tty)) {
1473                 unsigned char start_char = START_CHAR(tty);
1474                 status = edge_write(tty, port, &start_char, 1);
1475                 if (status <= 0)
1476                         return;
1477         }
1478         /* if we are implementing RTS/CTS, toggle that line */
1479         if (tty->termios.c_cflag & CRTSCTS) {
1480                 edge_port->shadowMCR |= MCR_RTS;
1481                 send_cmd_write_uart_register(edge_port, MCR,
1482                                                 edge_port->shadowMCR);
1483         }
1484 }
1485
1486
1487 /*****************************************************************************
1488  * SerialSetTermios
1489  *      this function is called by the tty driver when it wants to change
1490  * the termios structure
1491  *****************************************************************************/
1492 static void edge_set_termios(struct tty_struct *tty,
1493         struct usb_serial_port *port, struct ktermios *old_termios)
1494 {
1495         struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1496         unsigned int cflag;
1497
1498         cflag = tty->termios.c_cflag;
1499         dev_dbg(&port->dev, "%s - clfag %08x iflag %08x\n", __func__, tty->termios.c_cflag, tty->termios.c_iflag);
1500         dev_dbg(&port->dev, "%s - old clfag %08x old iflag %08x\n", __func__, old_termios->c_cflag, old_termios->c_iflag);
1501
1502         if (edge_port == NULL)
1503                 return;
1504
1505         if (!edge_port->open) {
1506                 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1507                 return;
1508         }
1509
1510         /* change the port settings to the new ones specified */
1511         change_port_settings(tty, edge_port, old_termios);
1512 }
1513
1514
1515 /*****************************************************************************
1516  * get_lsr_info - get line status register info
1517  *
1518  * Purpose: Let user call ioctl() to get info when the UART physically
1519  *          is emptied.  On bus types like RS485, the transmitter must
1520  *          release the bus after transmitting. This must be done when
1521  *          the transmit shift register is empty, not be done when the
1522  *          transmit holding register is empty.  This functionality
1523  *          allows an RS485 driver to be written in user space.
1524  *****************************************************************************/
1525 static int get_lsr_info(struct edgeport_port *edge_port,
1526                                                 unsigned int __user *value)
1527 {
1528         unsigned int result = 0;
1529         unsigned long flags;
1530
1531         spin_lock_irqsave(&edge_port->ep_lock, flags);
1532         if (edge_port->maxTxCredits == edge_port->txCredits &&
1533             edge_port->txfifo.count == 0) {
1534                 dev_dbg(&edge_port->port->dev, "%s -- Empty\n", __func__);
1535                 result = TIOCSER_TEMT;
1536         }
1537         spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1538
1539         if (copy_to_user(value, &result, sizeof(int)))
1540                 return -EFAULT;
1541         return 0;
1542 }
1543
1544 static int edge_tiocmset(struct tty_struct *tty,
1545                                         unsigned int set, unsigned int clear)
1546 {
1547         struct usb_serial_port *port = tty->driver_data;
1548         struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1549         unsigned int mcr;
1550
1551         mcr = edge_port->shadowMCR;
1552         if (set & TIOCM_RTS)
1553                 mcr |= MCR_RTS;
1554         if (set & TIOCM_DTR)
1555                 mcr |= MCR_DTR;
1556         if (set & TIOCM_LOOP)
1557                 mcr |= MCR_LOOPBACK;
1558
1559         if (clear & TIOCM_RTS)
1560                 mcr &= ~MCR_RTS;
1561         if (clear & TIOCM_DTR)
1562                 mcr &= ~MCR_DTR;
1563         if (clear & TIOCM_LOOP)
1564                 mcr &= ~MCR_LOOPBACK;
1565
1566         edge_port->shadowMCR = mcr;
1567
1568         send_cmd_write_uart_register(edge_port, MCR, edge_port->shadowMCR);
1569
1570         return 0;
1571 }
1572
1573 static int edge_tiocmget(struct tty_struct *tty)
1574 {
1575         struct usb_serial_port *port = tty->driver_data;
1576         struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1577         unsigned int result = 0;
1578         unsigned int msr;
1579         unsigned int mcr;
1580
1581         msr = edge_port->shadowMSR;
1582         mcr = edge_port->shadowMCR;
1583         result = ((mcr & MCR_DTR)       ? TIOCM_DTR: 0)   /* 0x002 */
1584                   | ((mcr & MCR_RTS)    ? TIOCM_RTS: 0)   /* 0x004 */
1585                   | ((msr & EDGEPORT_MSR_CTS)   ? TIOCM_CTS: 0)   /* 0x020 */
1586                   | ((msr & EDGEPORT_MSR_CD)    ? TIOCM_CAR: 0)   /* 0x040 */
1587                   | ((msr & EDGEPORT_MSR_RI)    ? TIOCM_RI:  0)   /* 0x080 */
1588                   | ((msr & EDGEPORT_MSR_DSR)   ? TIOCM_DSR: 0);  /* 0x100 */
1589
1590         return result;
1591 }
1592
1593 static int edge_get_icount(struct tty_struct *tty,
1594                                 struct serial_icounter_struct *icount)
1595 {
1596         struct usb_serial_port *port = tty->driver_data;
1597         struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1598         struct async_icount cnow;
1599         cnow = edge_port->icount;
1600
1601         icount->cts = cnow.cts;
1602         icount->dsr = cnow.dsr;
1603         icount->rng = cnow.rng;
1604         icount->dcd = cnow.dcd;
1605         icount->rx = cnow.rx;
1606         icount->tx = cnow.tx;
1607         icount->frame = cnow.frame;
1608         icount->overrun = cnow.overrun;
1609         icount->parity = cnow.parity;
1610         icount->brk = cnow.brk;
1611         icount->buf_overrun = cnow.buf_overrun;
1612
1613         dev_dbg(&port->dev, "%s (%d) TIOCGICOUNT RX=%d, TX=%d\n", __func__,
1614                 port->number, icount->rx, icount->tx);
1615         return 0;
1616 }
1617
1618 static int get_serial_info(struct edgeport_port *edge_port,
1619                                 struct serial_struct __user *retinfo)
1620 {
1621         struct serial_struct tmp;
1622
1623         if (!retinfo)
1624                 return -EFAULT;
1625
1626         memset(&tmp, 0, sizeof(tmp));
1627
1628         tmp.type                = PORT_16550A;
1629         tmp.line                = edge_port->port->serial->minor;
1630         tmp.port                = edge_port->port->number;
1631         tmp.irq                 = 0;
1632         tmp.flags               = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ;
1633         tmp.xmit_fifo_size      = edge_port->maxTxCredits;
1634         tmp.baud_base           = 9600;
1635         tmp.close_delay         = 5*HZ;
1636         tmp.closing_wait        = 30*HZ;
1637
1638         if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
1639                 return -EFAULT;
1640         return 0;
1641 }
1642
1643
1644 /*****************************************************************************
1645  * SerialIoctl
1646  *      this function handles any ioctl calls to the driver
1647  *****************************************************************************/
1648 static int edge_ioctl(struct tty_struct *tty,
1649                                         unsigned int cmd, unsigned long arg)
1650 {
1651         struct usb_serial_port *port = tty->driver_data;
1652         DEFINE_WAIT(wait);
1653         struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1654         struct async_icount cnow;
1655         struct async_icount cprev;
1656
1657         dev_dbg(&port->dev, "%s - port %d, cmd = 0x%x\n", __func__, port->number, cmd);
1658
1659         switch (cmd) {
1660         case TIOCSERGETLSR:
1661                 dev_dbg(&port->dev, "%s (%d) TIOCSERGETLSR\n", __func__,  port->number);
1662                 return get_lsr_info(edge_port, (unsigned int __user *) arg);
1663
1664         case TIOCGSERIAL:
1665                 dev_dbg(&port->dev, "%s (%d) TIOCGSERIAL\n", __func__,  port->number);
1666                 return get_serial_info(edge_port, (struct serial_struct __user *) arg);
1667
1668         case TIOCMIWAIT:
1669                 dev_dbg(&port->dev, "%s (%d) TIOCMIWAIT\n", __func__,  port->number);
1670                 cprev = edge_port->icount;
1671                 while (1) {
1672                         prepare_to_wait(&edge_port->delta_msr_wait,
1673                                                 &wait, TASK_INTERRUPTIBLE);
1674                         schedule();
1675                         finish_wait(&edge_port->delta_msr_wait, &wait);
1676                         /* see if a signal did it */
1677                         if (signal_pending(current))
1678                                 return -ERESTARTSYS;
1679                         cnow = edge_port->icount;
1680                         if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
1681                             cnow.dcd == cprev.dcd && cnow.cts == cprev.cts)
1682                                 return -EIO; /* no change => error */
1683                         if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) ||
1684                             ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) ||
1685                             ((arg & TIOCM_CD)  && (cnow.dcd != cprev.dcd)) ||
1686                             ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) {
1687                                 return 0;
1688                         }
1689                         cprev = cnow;
1690                 }
1691                 /* NOTREACHED */
1692                 break;
1693
1694         }
1695         return -ENOIOCTLCMD;
1696 }
1697
1698
1699 /*****************************************************************************
1700  * SerialBreak
1701  *      this function sends a break to the port
1702  *****************************************************************************/
1703 static void edge_break(struct tty_struct *tty, int break_state)
1704 {
1705         struct usb_serial_port *port = tty->driver_data;
1706         struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1707         struct edgeport_serial *edge_serial = usb_get_serial_data(port->serial);
1708         int status;
1709
1710         if ((!edge_serial->is_epic) ||
1711             ((edge_serial->is_epic) &&
1712              (edge_serial->epic_descriptor.Supports.IOSPChase))) {
1713                 /* flush and chase */
1714                 edge_port->chaseResponsePending = true;
1715
1716                 dev_dbg(&port->dev, "%s - Sending IOSP_CMD_CHASE_PORT\n", __func__);
1717                 status = send_iosp_ext_cmd(edge_port, IOSP_CMD_CHASE_PORT, 0);
1718                 if (status == 0) {
1719                         /* block until chase finished */
1720                         block_until_chase_response(edge_port);
1721                 } else {
1722                         edge_port->chaseResponsePending = false;
1723                 }
1724         }
1725
1726         if ((!edge_serial->is_epic) ||
1727             ((edge_serial->is_epic) &&
1728              (edge_serial->epic_descriptor.Supports.IOSPSetClrBreak))) {
1729                 if (break_state == -1) {
1730                         dev_dbg(&port->dev, "%s - Sending IOSP_CMD_SET_BREAK\n", __func__);
1731                         status = send_iosp_ext_cmd(edge_port,
1732                                                 IOSP_CMD_SET_BREAK, 0);
1733                 } else {
1734                         dev_dbg(&port->dev, "%s - Sending IOSP_CMD_CLEAR_BREAK\n", __func__);
1735                         status = send_iosp_ext_cmd(edge_port,
1736                                                 IOSP_CMD_CLEAR_BREAK, 0);
1737                 }
1738                 if (status)
1739                         dev_dbg(&port->dev, "%s - error sending break set/clear command.\n",
1740                                 __func__);
1741         }
1742 }
1743
1744
1745 /*****************************************************************************
1746  * process_rcvd_data
1747  *      this function handles the data received on the bulk in pipe.
1748  *****************************************************************************/
1749 static void process_rcvd_data(struct edgeport_serial *edge_serial,
1750                                 unsigned char *buffer, __u16 bufferLength)
1751 {
1752         struct device *dev = &edge_serial->serial->dev->dev;
1753         struct usb_serial_port *port;
1754         struct edgeport_port *edge_port;
1755         struct tty_struct *tty;
1756         __u16 lastBufferLength;
1757         __u16 rxLen;
1758
1759         lastBufferLength = bufferLength + 1;
1760
1761         while (bufferLength > 0) {
1762                 /* failsafe incase we get a message that we don't understand */
1763                 if (lastBufferLength == bufferLength) {
1764                         dev_dbg(dev, "%s - stuck in loop, exiting it.\n", __func__);
1765                         break;
1766                 }
1767                 lastBufferLength = bufferLength;
1768
1769                 switch (edge_serial->rxState) {
1770                 case EXPECT_HDR1:
1771                         edge_serial->rxHeader1 = *buffer;
1772                         ++buffer;
1773                         --bufferLength;
1774
1775                         if (bufferLength == 0) {
1776                                 edge_serial->rxState = EXPECT_HDR2;
1777                                 break;
1778                         }
1779                         /* otherwise, drop on through */
1780                 case EXPECT_HDR2:
1781                         edge_serial->rxHeader2 = *buffer;
1782                         ++buffer;
1783                         --bufferLength;
1784
1785                         dev_dbg(dev, "%s - Hdr1=%02X Hdr2=%02X\n", __func__,
1786                                 edge_serial->rxHeader1, edge_serial->rxHeader2);
1787                         /* Process depending on whether this header is
1788                          * data or status */
1789
1790                         if (IS_CMD_STAT_HDR(edge_serial->rxHeader1)) {
1791                                 /* Decode this status header and go to
1792                                  * EXPECT_HDR1 (if we can process the status
1793                                  * with only 2 bytes), or go to EXPECT_HDR3 to
1794                                  * get the third byte. */
1795                                 edge_serial->rxPort =
1796                                     IOSP_GET_HDR_PORT(edge_serial->rxHeader1);
1797                                 edge_serial->rxStatusCode =
1798                                     IOSP_GET_STATUS_CODE(
1799                                                 edge_serial->rxHeader1);
1800
1801                                 if (!IOSP_STATUS_IS_2BYTE(
1802                                                 edge_serial->rxStatusCode)) {
1803                                         /* This status needs additional bytes.
1804                                          * Save what we have and then wait for
1805                                          * more data.
1806                                          */
1807                                         edge_serial->rxStatusParam
1808                                                 = edge_serial->rxHeader2;
1809                                         edge_serial->rxState = EXPECT_HDR3;
1810                                         break;
1811                                 }
1812                                 /* We have all the header bytes, process the
1813                                    status now */
1814                                 process_rcvd_status(edge_serial,
1815                                                 edge_serial->rxHeader2, 0);
1816                                 edge_serial->rxState = EXPECT_HDR1;
1817                                 break;
1818                         } else {
1819                                 edge_serial->rxPort =
1820                                     IOSP_GET_HDR_PORT(edge_serial->rxHeader1);
1821                                 edge_serial->rxBytesRemaining =
1822                                     IOSP_GET_HDR_DATA_LEN(
1823                                                 edge_serial->rxHeader1,
1824                                                 edge_serial->rxHeader2);
1825                                 dev_dbg(dev, "%s - Data for Port %u Len %u\n",
1826                                         __func__,
1827                                         edge_serial->rxPort,
1828                                         edge_serial->rxBytesRemaining);
1829
1830                                 /* ASSERT(DevExt->RxPort < DevExt->NumPorts);
1831                                  * ASSERT(DevExt->RxBytesRemaining <
1832                                  *              IOSP_MAX_DATA_LENGTH);
1833                                  */
1834
1835                                 if (bufferLength == 0) {
1836                                         edge_serial->rxState = EXPECT_DATA;
1837                                         break;
1838                                 }
1839                                 /* Else, drop through */
1840                         }
1841                 case EXPECT_DATA: /* Expect data */
1842                         if (bufferLength < edge_serial->rxBytesRemaining) {
1843                                 rxLen = bufferLength;
1844                                 /* Expect data to start next buffer */
1845                                 edge_serial->rxState = EXPECT_DATA;
1846                         } else {
1847                                 /* BufLen >= RxBytesRemaining */
1848                                 rxLen = edge_serial->rxBytesRemaining;
1849                                 /* Start another header next time */
1850                                 edge_serial->rxState = EXPECT_HDR1;
1851                         }
1852
1853                         bufferLength -= rxLen;
1854                         edge_serial->rxBytesRemaining -= rxLen;
1855
1856                         /* spit this data back into the tty driver if this
1857                            port is open */
1858                         if (rxLen) {
1859                                 port = edge_serial->serial->port[
1860                                                         edge_serial->rxPort];
1861                                 edge_port = usb_get_serial_port_data(port);
1862                                 if (edge_port->open) {
1863                                         tty = tty_port_tty_get(
1864                                                 &edge_port->port->port);
1865                                         if (tty) {
1866                                                 dev_dbg(dev, "%s - Sending %d bytes to TTY for port %d\n",
1867                                                         __func__, rxLen, edge_serial->rxPort);
1868                                                 edge_tty_recv(&edge_serial->serial->dev->dev, tty, buffer, rxLen);
1869                                                 tty_kref_put(tty);
1870                                         }
1871                                         edge_port->icount.rx += rxLen;
1872                                 }
1873                                 buffer += rxLen;
1874                         }
1875                         break;
1876
1877                 case EXPECT_HDR3:       /* Expect 3rd byte of status header */
1878                         edge_serial->rxHeader3 = *buffer;
1879                         ++buffer;
1880                         --bufferLength;
1881
1882                         /* We have all the header bytes, process the
1883                            status now */
1884                         process_rcvd_status(edge_serial,
1885                                 edge_serial->rxStatusParam,
1886                                 edge_serial->rxHeader3);
1887                         edge_serial->rxState = EXPECT_HDR1;
1888                         break;
1889                 }
1890         }
1891 }
1892
1893
1894 /*****************************************************************************
1895  * process_rcvd_status
1896  *      this function handles the any status messages received on the
1897  *      bulk in pipe.
1898  *****************************************************************************/
1899 static void process_rcvd_status(struct edgeport_serial *edge_serial,
1900                                                 __u8 byte2, __u8 byte3)
1901 {
1902         struct usb_serial_port *port;
1903         struct edgeport_port *edge_port;
1904         struct tty_struct *tty;
1905         struct device *dev;
1906         __u8 code = edge_serial->rxStatusCode;
1907
1908         /* switch the port pointer to the one being currently talked about */
1909         port = edge_serial->serial->port[edge_serial->rxPort];
1910         edge_port = usb_get_serial_port_data(port);
1911         if (edge_port == NULL) {
1912                 dev_err(&edge_serial->serial->dev->dev,
1913                         "%s - edge_port == NULL for port %d\n",
1914                                         __func__, edge_serial->rxPort);
1915                 return;
1916         }
1917         dev = &port->dev;
1918
1919         if (code == IOSP_EXT_STATUS) {
1920                 switch (byte2) {
1921                 case IOSP_EXT_STATUS_CHASE_RSP:
1922                         /* we want to do EXT status regardless of port
1923                          * open/closed */
1924                         dev_dbg(dev, "%s - Port %u EXT CHASE_RSP Data = %02x\n",
1925                                 __func__, edge_serial->rxPort, byte3);
1926                         /* Currently, the only EXT_STATUS is Chase, so process
1927                          * here instead of one more call to one more subroutine
1928                          * If/when more EXT_STATUS, there'll be more work to do
1929                          * Also, we currently clear flag and close the port
1930                          * regardless of content of above's Byte3.
1931                          * We could choose to do something else when Byte3 says
1932                          * Timeout on Chase from Edgeport, like wait longer in
1933                          * block_until_chase_response, but for now we don't.
1934                          */
1935                         edge_port->chaseResponsePending = false;
1936                         wake_up(&edge_port->wait_chase);
1937                         return;
1938
1939                 case IOSP_EXT_STATUS_RX_CHECK_RSP:
1940                         dev_dbg(dev, "%s ========== Port %u CHECK_RSP Sequence = %02x =============\n",
1941                                 __func__, edge_serial->rxPort, byte3);
1942                         /* Port->RxCheckRsp = true; */
1943                         return;
1944                 }
1945         }
1946
1947         if (code == IOSP_STATUS_OPEN_RSP) {
1948                 edge_port->txCredits = GET_TX_BUFFER_SIZE(byte3);
1949                 edge_port->maxTxCredits = edge_port->txCredits;
1950                 dev_dbg(dev, "%s - Port %u Open Response Initial MSR = %02x TxBufferSize = %d\n",
1951                         __func__, edge_serial->rxPort, byte2, edge_port->txCredits);
1952                 handle_new_msr(edge_port, byte2);
1953
1954                 /* send the current line settings to the port so we are
1955                    in sync with any further termios calls */
1956                 tty = tty_port_tty_get(&edge_port->port->port);
1957                 if (tty) {
1958                         change_port_settings(tty,
1959                                 edge_port, &tty->termios);
1960                         tty_kref_put(tty);
1961                 }
1962
1963                 /* we have completed the open */
1964                 edge_port->openPending = false;
1965                 edge_port->open = true;
1966                 wake_up(&edge_port->wait_open);
1967                 return;
1968         }
1969
1970         /* If port is closed, silently discard all rcvd status. We can
1971          * have cases where buffered status is received AFTER the close
1972          * port command is sent to the Edgeport.
1973          */
1974         if (!edge_port->open || edge_port->closePending)
1975                 return;
1976
1977         switch (code) {
1978         /* Not currently sent by Edgeport */
1979         case IOSP_STATUS_LSR:
1980                 dev_dbg(dev, "%s - Port %u LSR Status = %02x\n",
1981                         __func__, edge_serial->rxPort, byte2);
1982                 handle_new_lsr(edge_port, false, byte2, 0);
1983                 break;
1984
1985         case IOSP_STATUS_LSR_DATA:
1986                 dev_dbg(dev, "%s - Port %u LSR Status = %02x, Data = %02x\n",
1987                         __func__, edge_serial->rxPort, byte2, byte3);
1988                 /* byte2 is LSR Register */
1989                 /* byte3 is broken data byte */
1990                 handle_new_lsr(edge_port, true, byte2, byte3);
1991                 break;
1992         /*
1993          *      case IOSP_EXT_4_STATUS:
1994          *              dev_dbg(dev, "%s - Port %u LSR Status = %02x Data = %02x\n",
1995          *                      __func__, edge_serial->rxPort, byte2, byte3);
1996          *              break;
1997          */
1998         case IOSP_STATUS_MSR:
1999                 dev_dbg(dev, "%s - Port %u MSR Status = %02x\n",
2000                         __func__, edge_serial->rxPort, byte2);
2001                 /*
2002                  * Process this new modem status and generate appropriate
2003                  * events, etc, based on the new status. This routine
2004                  * also saves the MSR in Port->ShadowMsr.
2005                  */
2006                 handle_new_msr(edge_port, byte2);
2007                 break;
2008
2009         default:
2010                 dev_dbg(dev, "%s - Unrecognized IOSP status code %u\n", __func__, code);
2011                 break;
2012         }
2013 }
2014
2015
2016 /*****************************************************************************
2017  * edge_tty_recv
2018  *      this function passes data on to the tty flip buffer
2019  *****************************************************************************/
2020 static void edge_tty_recv(struct device *dev, struct tty_struct *tty,
2021                                         unsigned char *data, int length)
2022 {
2023         int cnt;
2024
2025         cnt = tty_insert_flip_string(tty, data, length);
2026         if (cnt < length) {
2027                 dev_err(dev, "%s - dropping data, %d bytes lost\n",
2028                                 __func__, length - cnt);
2029         }
2030         data += cnt;
2031         length -= cnt;
2032
2033         tty_flip_buffer_push(tty);
2034 }
2035
2036
2037 /*****************************************************************************
2038  * handle_new_msr
2039  *      this function handles any change to the msr register for a port.
2040  *****************************************************************************/
2041 static void handle_new_msr(struct edgeport_port *edge_port, __u8 newMsr)
2042 {
2043         struct  async_icount *icount;
2044
2045         if (newMsr & (EDGEPORT_MSR_DELTA_CTS | EDGEPORT_MSR_DELTA_DSR |
2046                         EDGEPORT_MSR_DELTA_RI | EDGEPORT_MSR_DELTA_CD)) {
2047                 icount = &edge_port->icount;
2048
2049                 /* update input line counters */
2050                 if (newMsr & EDGEPORT_MSR_DELTA_CTS)
2051                         icount->cts++;
2052                 if (newMsr & EDGEPORT_MSR_DELTA_DSR)
2053                         icount->dsr++;
2054                 if (newMsr & EDGEPORT_MSR_DELTA_CD)
2055                         icount->dcd++;
2056                 if (newMsr & EDGEPORT_MSR_DELTA_RI)
2057                         icount->rng++;
2058                 wake_up_interruptible(&edge_port->delta_msr_wait);
2059         }
2060
2061         /* Save the new modem status */
2062         edge_port->shadowMSR = newMsr & 0xf0;
2063 }
2064
2065
2066 /*****************************************************************************
2067  * handle_new_lsr
2068  *      this function handles any change to the lsr register for a port.
2069  *****************************************************************************/
2070 static void handle_new_lsr(struct edgeport_port *edge_port, __u8 lsrData,
2071                                                         __u8 lsr, __u8 data)
2072 {
2073         __u8 newLsr = (__u8) (lsr & (__u8)
2074                 (LSR_OVER_ERR | LSR_PAR_ERR | LSR_FRM_ERR | LSR_BREAK));
2075         struct async_icount *icount;
2076
2077         edge_port->shadowLSR = lsr;
2078
2079         if (newLsr & LSR_BREAK) {
2080                 /*
2081                  * Parity and Framing errors only count if they
2082                  * occur exclusive of a break being
2083                  * received.
2084                  */
2085                 newLsr &= (__u8)(LSR_OVER_ERR | LSR_BREAK);
2086         }
2087
2088         /* Place LSR data byte into Rx buffer */
2089         if (lsrData) {
2090                 struct tty_struct *tty =
2091                                 tty_port_tty_get(&edge_port->port->port);
2092                 if (tty) {
2093                         edge_tty_recv(&edge_port->port->dev, tty, &data, 1);
2094                         tty_kref_put(tty);
2095                 }
2096         }
2097         /* update input line counters */
2098         icount = &edge_port->icount;
2099         if (newLsr & LSR_BREAK)
2100                 icount->brk++;
2101         if (newLsr & LSR_OVER_ERR)
2102                 icount->overrun++;
2103         if (newLsr & LSR_PAR_ERR)
2104                 icount->parity++;
2105         if (newLsr & LSR_FRM_ERR)
2106                 icount->frame++;
2107 }
2108
2109
2110 /****************************************************************************
2111  * sram_write
2112  *      writes a number of bytes to the Edgeport device's sram starting at the
2113  *      given address.
2114  *      If successful returns the number of bytes written, otherwise it returns
2115  *      a negative error number of the problem.
2116  ****************************************************************************/
2117 static int sram_write(struct usb_serial *serial, __u16 extAddr, __u16 addr,
2118                                         __u16 length, const __u8 *data)
2119 {
2120         int result;
2121         __u16 current_length;
2122         unsigned char *transfer_buffer;
2123
2124         dev_dbg(&serial->dev->dev, "%s - %x, %x, %d\n", __func__, extAddr, addr, length);
2125
2126         transfer_buffer =  kmalloc(64, GFP_KERNEL);
2127         if (!transfer_buffer) {
2128                 dev_err(&serial->dev->dev, "%s - kmalloc(%d) failed.\n",
2129                                                         __func__, 64);
2130                 return -ENOMEM;
2131         }
2132
2133         /* need to split these writes up into 64 byte chunks */
2134         result = 0;
2135         while (length > 0) {
2136                 if (length > 64)
2137                         current_length = 64;
2138                 else
2139                         current_length = length;
2140
2141 /*              dev_dbg(&serial->dev->dev, "%s - writing %x, %x, %d\n", __func__, extAddr, addr, current_length); */
2142                 memcpy(transfer_buffer, data, current_length);
2143                 result = usb_control_msg(serial->dev,
2144                                         usb_sndctrlpipe(serial->dev, 0),
2145                                         USB_REQUEST_ION_WRITE_RAM,
2146                                         0x40, addr, extAddr, transfer_buffer,
2147                                         current_length, 300);
2148                 if (result < 0)
2149                         break;
2150                 length -= current_length;
2151                 addr += current_length;
2152                 data += current_length;
2153         }
2154
2155         kfree(transfer_buffer);
2156         return result;
2157 }
2158
2159
2160 /****************************************************************************
2161  * rom_write
2162  *      writes a number of bytes to the Edgeport device's ROM starting at the
2163  *      given address.
2164  *      If successful returns the number of bytes written, otherwise it returns
2165  *      a negative error number of the problem.
2166  ****************************************************************************/
2167 static int rom_write(struct usb_serial *serial, __u16 extAddr, __u16 addr,
2168                                         __u16 length, const __u8 *data)
2169 {
2170         int result;
2171         __u16 current_length;
2172         unsigned char *transfer_buffer;
2173
2174         transfer_buffer =  kmalloc(64, GFP_KERNEL);
2175         if (!transfer_buffer) {
2176                 dev_err(&serial->dev->dev, "%s - kmalloc(%d) failed.\n",
2177                                                                 __func__, 64);
2178                 return -ENOMEM;
2179         }
2180
2181         /* need to split these writes up into 64 byte chunks */
2182         result = 0;
2183         while (length > 0) {
2184                 if (length > 64)
2185                         current_length = 64;
2186                 else
2187                         current_length = length;
2188                 memcpy(transfer_buffer, data, current_length);
2189                 result = usb_control_msg(serial->dev,
2190                                         usb_sndctrlpipe(serial->dev, 0),
2191                                         USB_REQUEST_ION_WRITE_ROM, 0x40,
2192                                         addr, extAddr,
2193                                         transfer_buffer, current_length, 300);
2194                 if (result < 0)
2195                         break;
2196                 length -= current_length;
2197                 addr += current_length;
2198                 data += current_length;
2199         }
2200
2201         kfree(transfer_buffer);
2202         return result;
2203 }
2204
2205
2206 /****************************************************************************
2207  * rom_read
2208  *      reads a number of bytes from the Edgeport device starting at the given
2209  *      address.
2210  *      If successful returns the number of bytes read, otherwise it returns
2211  *      a negative error number of the problem.
2212  ****************************************************************************/
2213 static int rom_read(struct usb_serial *serial, __u16 extAddr,
2214                                         __u16 addr, __u16 length, __u8 *data)
2215 {
2216         int result;
2217         __u16 current_length;
2218         unsigned char *transfer_buffer;
2219
2220         transfer_buffer =  kmalloc(64, GFP_KERNEL);
2221         if (!transfer_buffer) {
2222                 dev_err(&serial->dev->dev,
2223                         "%s - kmalloc(%d) failed.\n", __func__, 64);
2224                 return -ENOMEM;
2225         }
2226
2227         /* need to split these reads up into 64 byte chunks */
2228         result = 0;
2229         while (length > 0) {
2230                 if (length > 64)
2231                         current_length = 64;
2232                 else
2233                         current_length = length;
2234                 result = usb_control_msg(serial->dev,
2235                                         usb_rcvctrlpipe(serial->dev, 0),
2236                                         USB_REQUEST_ION_READ_ROM,
2237                                         0xC0, addr, extAddr, transfer_buffer,
2238                                         current_length, 300);
2239                 if (result < 0)
2240                         break;
2241                 memcpy(data, transfer_buffer, current_length);
2242                 length -= current_length;
2243                 addr += current_length;
2244                 data += current_length;
2245         }
2246
2247         kfree(transfer_buffer);
2248         return result;
2249 }
2250
2251
2252 /****************************************************************************
2253  * send_iosp_ext_cmd
2254  *      Is used to send a IOSP message to the Edgeport device
2255  ****************************************************************************/
2256 static int send_iosp_ext_cmd(struct edgeport_port *edge_port,
2257                                                 __u8 command, __u8 param)
2258 {
2259         unsigned char   *buffer;
2260         unsigned char   *currentCommand;
2261         int             length = 0;
2262         int             status = 0;
2263
2264         buffer = kmalloc(10, GFP_ATOMIC);
2265         if (!buffer) {
2266                 dev_err(&edge_port->port->dev,
2267                                 "%s - kmalloc(%d) failed.\n", __func__, 10);
2268                 return -ENOMEM;
2269         }
2270
2271         currentCommand = buffer;
2272
2273         MAKE_CMD_EXT_CMD(&currentCommand, &length,
2274                 edge_port->port->number - edge_port->port->serial->minor,
2275                 command, param);
2276
2277         status = write_cmd_usb(edge_port, buffer, length);
2278         if (status) {
2279                 /* something bad happened, let's free up the memory */
2280                 kfree(buffer);
2281         }
2282
2283         return status;
2284 }
2285
2286
2287 /*****************************************************************************
2288  * write_cmd_usb
2289  *      this function writes the given buffer out to the bulk write endpoint.
2290  *****************************************************************************/
2291 static int write_cmd_usb(struct edgeport_port *edge_port,
2292                                         unsigned char *buffer, int length)
2293 {
2294         struct edgeport_serial *edge_serial =
2295                                 usb_get_serial_data(edge_port->port->serial);
2296         struct device *dev = &edge_port->port->dev;
2297         int status = 0;
2298         struct urb *urb;
2299
2300         usb_serial_debug_data(dev, __func__, length, buffer);
2301
2302         /* Allocate our next urb */
2303         urb = usb_alloc_urb(0, GFP_ATOMIC);
2304         if (!urb)
2305                 return -ENOMEM;
2306
2307         atomic_inc(&CmdUrbs);
2308         dev_dbg(dev, "%s - ALLOCATE URB %p (outstanding %d)\n",
2309                 __func__, urb, atomic_read(&CmdUrbs));
2310
2311         usb_fill_bulk_urb(urb, edge_serial->serial->dev,
2312                         usb_sndbulkpipe(edge_serial->serial->dev,
2313                                         edge_serial->bulk_out_endpoint),
2314                         buffer, length, edge_bulk_out_cmd_callback, edge_port);
2315
2316         edge_port->commandPending = true;
2317         status = usb_submit_urb(urb, GFP_ATOMIC);
2318
2319         if (status) {
2320                 /* something went wrong */
2321                 dev_err(dev, "%s - usb_submit_urb(write command) failed, status = %d\n",
2322                         __func__, status);
2323                 usb_kill_urb(urb);
2324                 usb_free_urb(urb);
2325                 atomic_dec(&CmdUrbs);
2326                 return status;
2327         }
2328
2329 #if 0
2330         wait_event(&edge_port->wait_command, !edge_port->commandPending);
2331
2332         if (edge_port->commandPending) {
2333                 /* command timed out */
2334                 dev_dbg(dev, "%s - command timed out\n", __func__);
2335                 status = -EINVAL;
2336         }
2337 #endif
2338         return status;
2339 }
2340
2341
2342 /*****************************************************************************
2343  * send_cmd_write_baud_rate
2344  *      this function sends the proper command to change the baud rate of the
2345  *      specified port.
2346  *****************************************************************************/
2347 static int send_cmd_write_baud_rate(struct edgeport_port *edge_port,
2348                                                                 int baudRate)
2349 {
2350         struct edgeport_serial *edge_serial =
2351                                 usb_get_serial_data(edge_port->port->serial);
2352         struct device *dev = &edge_port->port->dev;
2353         unsigned char *cmdBuffer;
2354         unsigned char *currCmd;
2355         int cmdLen = 0;
2356         int divisor;
2357         int status;
2358         unsigned char number =
2359                 edge_port->port->number - edge_port->port->serial->minor;
2360
2361         if (edge_serial->is_epic &&
2362             !edge_serial->epic_descriptor.Supports.IOSPSetBaudRate) {
2363                 dev_dbg(dev, "SendCmdWriteBaudRate - NOT Setting baud rate for port = %d, baud = %d\n",
2364                         edge_port->port->number, baudRate);
2365                 return 0;
2366         }
2367
2368         dev_dbg(dev, "%s - port = %d, baud = %d\n", __func__,
2369                 edge_port->port->number, baudRate);
2370
2371         status = calc_baud_rate_divisor(dev, baudRate, &divisor);
2372         if (status) {
2373                 dev_err(dev, "%s - bad baud rate\n", __func__);
2374                 return status;
2375         }
2376
2377         /* Alloc memory for the string of commands. */
2378         cmdBuffer =  kmalloc(0x100, GFP_ATOMIC);
2379         if (!cmdBuffer) {
2380                 dev_err(dev, "%s - kmalloc(%d) failed.\n", __func__, 0x100);
2381                 return -ENOMEM;
2382         }
2383         currCmd = cmdBuffer;
2384
2385         /* Enable access to divisor latch */
2386         MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, number, LCR, LCR_DL_ENABLE);
2387
2388         /* Write the divisor itself */
2389         MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, number, DLL, LOW8(divisor));
2390         MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, number, DLM, HIGH8(divisor));
2391
2392         /* Restore original value to disable access to divisor latch */
2393         MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, number, LCR,
2394                                                 edge_port->shadowLCR);
2395
2396         status = write_cmd_usb(edge_port, cmdBuffer, cmdLen);
2397         if (status) {
2398                 /* something bad happened, let's free up the memory */
2399                 kfree(cmdBuffer);
2400         }
2401
2402         return status;
2403 }
2404
2405
2406 /*****************************************************************************
2407  * calc_baud_rate_divisor
2408  *      this function calculates the proper baud rate divisor for the specified
2409  *      baud rate.
2410  *****************************************************************************/
2411 static int calc_baud_rate_divisor(struct device *dev, int baudrate, int *divisor)
2412 {
2413         int i;
2414         __u16 custom;
2415
2416         for (i = 0; i < ARRAY_SIZE(divisor_table); i++) {
2417                 if (divisor_table[i].BaudRate == baudrate) {
2418                         *divisor = divisor_table[i].Divisor;
2419                         return 0;
2420                 }
2421         }
2422
2423         /* We have tried all of the standard baud rates
2424          * lets try to calculate the divisor for this baud rate
2425          * Make sure the baud rate is reasonable */
2426         if (baudrate > 50 && baudrate < 230400) {
2427                 /* get divisor */
2428                 custom = (__u16)((230400L + baudrate/2) / baudrate);
2429
2430                 *divisor = custom;
2431
2432                 dev_dbg(dev, "%s - Baud %d = %d\n", __func__, baudrate, custom);
2433                 return 0;
2434         }
2435
2436         return -1;
2437 }
2438
2439
2440 /*****************************************************************************
2441  * send_cmd_write_uart_register
2442  *  this function builds up a uart register message and sends to the device.
2443  *****************************************************************************/
2444 static int send_cmd_write_uart_register(struct edgeport_port *edge_port,
2445                                                 __u8 regNum, __u8 regValue)
2446 {
2447         struct edgeport_serial *edge_serial =
2448                                 usb_get_serial_data(edge_port->port->serial);
2449         struct device *dev = &edge_port->port->dev;
2450         unsigned char *cmdBuffer;
2451         unsigned char *currCmd;
2452         unsigned long cmdLen = 0;
2453         int status;
2454
2455         dev_dbg(dev, "%s - write to %s register 0x%02x\n",
2456                 (regNum == MCR) ? "MCR" : "LCR", __func__, regValue);
2457
2458         if (edge_serial->is_epic &&
2459             !edge_serial->epic_descriptor.Supports.IOSPWriteMCR &&
2460             regNum == MCR) {
2461                 dev_dbg(dev, "SendCmdWriteUartReg - Not writing to MCR Register\n");
2462                 return 0;
2463         }
2464
2465         if (edge_serial->is_epic &&
2466             !edge_serial->epic_descriptor.Supports.IOSPWriteLCR &&
2467             regNum == LCR) {
2468                 dev_dbg(dev, "SendCmdWriteUartReg - Not writing to LCR Register\n");
2469                 return 0;
2470         }
2471
2472         /* Alloc memory for the string of commands. */
2473         cmdBuffer = kmalloc(0x10, GFP_ATOMIC);
2474         if (cmdBuffer == NULL)
2475                 return -ENOMEM;
2476
2477         currCmd = cmdBuffer;
2478
2479         /* Build a cmd in the buffer to write the given register */
2480         MAKE_CMD_WRITE_REG(&currCmd, &cmdLen,
2481                 edge_port->port->number - edge_port->port->serial->minor,
2482                 regNum, regValue);
2483
2484         status = write_cmd_usb(edge_port, cmdBuffer, cmdLen);
2485         if (status) {
2486                 /* something bad happened, let's free up the memory */
2487                 kfree(cmdBuffer);
2488         }
2489
2490         return status;
2491 }
2492
2493
2494 /*****************************************************************************
2495  * change_port_settings
2496  *      This routine is called to set the UART on the device to match the
2497  *      specified new settings.
2498  *****************************************************************************/
2499
2500 static void change_port_settings(struct tty_struct *tty,
2501         struct edgeport_port *edge_port, struct ktermios *old_termios)
2502 {
2503         struct device *dev = &edge_port->port->dev;
2504         struct edgeport_serial *edge_serial =
2505                         usb_get_serial_data(edge_port->port->serial);
2506         int baud;
2507         unsigned cflag;
2508         __u8 mask = 0xff;
2509         __u8 lData;
2510         __u8 lParity;
2511         __u8 lStop;
2512         __u8 rxFlow;
2513         __u8 txFlow;
2514         int status;
2515
2516         dev_dbg(dev, "%s - port %d\n", __func__, edge_port->port->number);
2517
2518         if (!edge_port->open &&
2519             !edge_port->openPending) {
2520                 dev_dbg(dev, "%s - port not opened\n", __func__);
2521                 return;
2522         }
2523
2524         cflag = tty->termios.c_cflag;
2525
2526         switch (cflag & CSIZE) {
2527         case CS5:
2528                 lData = LCR_BITS_5; mask = 0x1f;
2529                 dev_dbg(dev, "%s - data bits = 5\n", __func__);
2530                 break;
2531         case CS6:
2532                 lData = LCR_BITS_6; mask = 0x3f;
2533                 dev_dbg(dev, "%s - data bits = 6\n", __func__);
2534                 break;
2535         case CS7:
2536                 lData = LCR_BITS_7; mask = 0x7f;
2537                 dev_dbg(dev, "%s - data bits = 7\n", __func__);
2538                 break;
2539         default:
2540         case CS8:
2541                 lData = LCR_BITS_8;
2542                 dev_dbg(dev, "%s - data bits = 8\n", __func__);
2543                 break;
2544         }
2545
2546         lParity = LCR_PAR_NONE;
2547         if (cflag & PARENB) {
2548                 if (cflag & CMSPAR) {
2549                         if (cflag & PARODD) {
2550                                 lParity = LCR_PAR_MARK;
2551                                 dev_dbg(dev, "%s - parity = mark\n", __func__);
2552                         } else {
2553                                 lParity = LCR_PAR_SPACE;
2554                                 dev_dbg(dev, "%s - parity = space\n", __func__);
2555                         }
2556                 } else if (cflag & PARODD) {
2557                         lParity = LCR_PAR_ODD;
2558                         dev_dbg(dev, "%s - parity = odd\n", __func__);
2559                 } else {
2560                         lParity = LCR_PAR_EVEN;
2561                         dev_dbg(dev, "%s - parity = even\n", __func__);
2562                 }
2563         } else {
2564                 dev_dbg(dev, "%s - parity = none\n", __func__);
2565         }
2566
2567         if (cflag & CSTOPB) {
2568                 lStop = LCR_STOP_2;
2569                 dev_dbg(dev, "%s - stop bits = 2\n", __func__);
2570         } else {
2571                 lStop = LCR_STOP_1;
2572                 dev_dbg(dev, "%s - stop bits = 1\n", __func__);
2573         }
2574
2575         /* figure out the flow control settings */
2576         rxFlow = txFlow = 0x00;
2577         if (cflag & CRTSCTS) {
2578                 rxFlow |= IOSP_RX_FLOW_RTS;
2579                 txFlow |= IOSP_TX_FLOW_CTS;
2580                 dev_dbg(dev, "%s - RTS/CTS is enabled\n", __func__);
2581         } else {
2582                 dev_dbg(dev, "%s - RTS/CTS is disabled\n", __func__);
2583         }
2584
2585         /* if we are implementing XON/XOFF, set the start and stop character
2586            in the device */
2587         if (I_IXOFF(tty) || I_IXON(tty)) {
2588                 unsigned char stop_char  = STOP_CHAR(tty);
2589                 unsigned char start_char = START_CHAR(tty);
2590
2591                 if ((!edge_serial->is_epic) ||
2592                     ((edge_serial->is_epic) &&
2593                      (edge_serial->epic_descriptor.Supports.IOSPSetXChar))) {
2594                         send_iosp_ext_cmd(edge_port,
2595                                         IOSP_CMD_SET_XON_CHAR, start_char);
2596                         send_iosp_ext_cmd(edge_port,
2597                                         IOSP_CMD_SET_XOFF_CHAR, stop_char);
2598                 }
2599
2600                 /* if we are implementing INBOUND XON/XOFF */
2601                 if (I_IXOFF(tty)) {
2602                         rxFlow |= IOSP_RX_FLOW_XON_XOFF;
2603                         dev_dbg(dev, "%s - INBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x\n",
2604                                 __func__, start_char, stop_char);
2605                 } else {
2606                         dev_dbg(dev, "%s - INBOUND XON/XOFF is disabled\n", __func__);
2607                 }
2608
2609                 /* if we are implementing OUTBOUND XON/XOFF */
2610                 if (I_IXON(tty)) {
2611                         txFlow |= IOSP_TX_FLOW_XON_XOFF;
2612                         dev_dbg(dev, "%s - OUTBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x\n",
2613                                 __func__, start_char, stop_char);
2614                 } else {
2615                         dev_dbg(dev, "%s - OUTBOUND XON/XOFF is disabled\n", __func__);
2616                 }
2617         }
2618
2619         /* Set flow control to the configured value */
2620         if ((!edge_serial->is_epic) ||
2621             ((edge_serial->is_epic) &&
2622              (edge_serial->epic_descriptor.Supports.IOSPSetRxFlow)))
2623                 send_iosp_ext_cmd(edge_port, IOSP_CMD_SET_RX_FLOW, rxFlow);
2624         if ((!edge_serial->is_epic) ||
2625             ((edge_serial->is_epic) &&
2626              (edge_serial->epic_descriptor.Supports.IOSPSetTxFlow)))
2627                 send_iosp_ext_cmd(edge_port, IOSP_CMD_SET_TX_FLOW, txFlow);
2628
2629
2630         edge_port->shadowLCR &= ~(LCR_BITS_MASK | LCR_STOP_MASK | LCR_PAR_MASK);
2631         edge_port->shadowLCR |= (lData | lParity | lStop);
2632
2633         edge_port->validDataMask = mask;
2634
2635         /* Send the updated LCR value to the EdgePort */
2636         status = send_cmd_write_uart_register(edge_port, LCR,
2637                                                         edge_port->shadowLCR);
2638         if (status != 0)
2639                 return;
2640
2641         /* set up the MCR register and send it to the EdgePort */
2642         edge_port->shadowMCR = MCR_MASTER_IE;
2643         if (cflag & CBAUD)
2644                 edge_port->shadowMCR |= (MCR_DTR | MCR_RTS);
2645
2646         status = send_cmd_write_uart_register(edge_port, MCR,
2647                                                 edge_port->shadowMCR);
2648         if (status != 0)
2649                 return;
2650
2651         /* Determine divisor based on baud rate */
2652         baud = tty_get_baud_rate(tty);
2653         if (!baud) {
2654                 /* pick a default, any default... */
2655                 baud = 9600;
2656         }
2657
2658         dev_dbg(dev, "%s - baud rate = %d\n", __func__, baud);
2659         status = send_cmd_write_baud_rate(edge_port, baud);
2660         if (status == -1) {
2661                 /* Speed change was not possible - put back the old speed */
2662                 baud = tty_termios_baud_rate(old_termios);
2663                 tty_encode_baud_rate(tty, baud, baud);
2664         }
2665 }
2666
2667
2668 /****************************************************************************
2669  * unicode_to_ascii
2670  *      Turns a string from Unicode into ASCII.
2671  *      Doesn't do a good job with any characters that are outside the normal
2672  *      ASCII range, but it's only for debugging...
2673  *      NOTE: expects the unicode in LE format
2674  ****************************************************************************/
2675 static void unicode_to_ascii(char *string, int buflen,
2676                                         __le16 *unicode, int unicode_size)
2677 {
2678         int i;
2679
2680         if (buflen <= 0)        /* never happens, but... */
2681                 return;
2682         --buflen;               /* space for nul */
2683
2684         for (i = 0; i < unicode_size; i++) {
2685                 if (i >= buflen)
2686                         break;
2687                 string[i] = (char)(le16_to_cpu(unicode[i]));
2688         }
2689         string[i] = 0x00;
2690 }
2691
2692
2693 /****************************************************************************
2694  * get_manufacturing_desc
2695  *      reads in the manufacturing descriptor and stores it into the serial
2696  *      structure.
2697  ****************************************************************************/
2698 static void get_manufacturing_desc(struct edgeport_serial *edge_serial)
2699 {
2700         struct device *dev = &edge_serial->serial->dev->dev;
2701         int response;
2702
2703         dev_dbg(dev, "getting manufacturer descriptor\n");
2704
2705         response = rom_read(edge_serial->serial,
2706                                 (EDGE_MANUF_DESC_ADDR & 0xffff0000) >> 16,
2707                                 (__u16)(EDGE_MANUF_DESC_ADDR & 0x0000ffff),
2708                                 EDGE_MANUF_DESC_LEN,
2709                                 (__u8 *)(&edge_serial->manuf_descriptor));
2710
2711         if (response < 1)
2712                 dev_err(dev, "error in getting manufacturer descriptor\n");
2713         else {
2714                 char string[30];
2715                 dev_dbg(dev, "**Manufacturer Descriptor\n");
2716                 dev_dbg(dev, "  RomSize:        %dK\n",
2717                         edge_serial->manuf_descriptor.RomSize);
2718                 dev_dbg(dev, "  RamSize:        %dK\n",
2719                         edge_serial->manuf_descriptor.RamSize);
2720                 dev_dbg(dev, "  CpuRev:         %d\n",
2721                         edge_serial->manuf_descriptor.CpuRev);
2722                 dev_dbg(dev, "  BoardRev:       %d\n",
2723                         edge_serial->manuf_descriptor.BoardRev);
2724                 dev_dbg(dev, "  NumPorts:       %d\n",
2725                         edge_serial->manuf_descriptor.NumPorts);
2726                 dev_dbg(dev, "  DescDate:       %d/%d/%d\n",
2727                         edge_serial->manuf_descriptor.DescDate[0],
2728                         edge_serial->manuf_descriptor.DescDate[1],
2729                         edge_serial->manuf_descriptor.DescDate[2]+1900);
2730                 unicode_to_ascii(string, sizeof(string),
2731                         edge_serial->manuf_descriptor.SerialNumber,
2732                         edge_serial->manuf_descriptor.SerNumLength/2);
2733                 dev_dbg(dev, "  SerialNumber: %s\n", string);
2734                 unicode_to_ascii(string, sizeof(string),
2735                         edge_serial->manuf_descriptor.AssemblyNumber,
2736                         edge_serial->manuf_descriptor.AssemblyNumLength/2);
2737                 dev_dbg(dev, "  AssemblyNumber: %s\n", string);
2738                 unicode_to_ascii(string, sizeof(string),
2739                     edge_serial->manuf_descriptor.OemAssyNumber,
2740                     edge_serial->manuf_descriptor.OemAssyNumLength/2);
2741                 dev_dbg(dev, "  OemAssyNumber:  %s\n", string);
2742                 dev_dbg(dev, "  UartType:       %d\n",
2743                         edge_serial->manuf_descriptor.UartType);
2744                 dev_dbg(dev, "  IonPid:         %d\n",
2745                         edge_serial->manuf_descriptor.IonPid);
2746                 dev_dbg(dev, "  IonConfig:      %d\n",
2747                         edge_serial->manuf_descriptor.IonConfig);
2748         }
2749 }
2750
2751
2752 /****************************************************************************
2753  * get_boot_desc
2754  *      reads in the bootloader descriptor and stores it into the serial
2755  *      structure.
2756  ****************************************************************************/
2757 static void get_boot_desc(struct edgeport_serial *edge_serial)
2758 {
2759         struct device *dev = &edge_serial->serial->dev->dev;
2760         int response;
2761
2762         dev_dbg(dev, "getting boot descriptor\n");
2763
2764         response = rom_read(edge_serial->serial,
2765                                 (EDGE_BOOT_DESC_ADDR & 0xffff0000) >> 16,
2766                                 (__u16)(EDGE_BOOT_DESC_ADDR & 0x0000ffff),
2767                                 EDGE_BOOT_DESC_LEN,
2768                                 (__u8 *)(&edge_serial->boot_descriptor));
2769
2770         if (response < 1)
2771                 dev_err(dev, "error in getting boot descriptor\n");
2772         else {
2773                 dev_dbg(dev, "**Boot Descriptor:\n");
2774                 dev_dbg(dev, "  BootCodeLength: %d\n",
2775                         le16_to_cpu(edge_serial->boot_descriptor.BootCodeLength));
2776                 dev_dbg(dev, "  MajorVersion:   %d\n",
2777                         edge_serial->boot_descriptor.MajorVersion);
2778                 dev_dbg(dev, "  MinorVersion:   %d\n",
2779                         edge_serial->boot_descriptor.MinorVersion);
2780                 dev_dbg(dev, "  BuildNumber:    %d\n",
2781                         le16_to_cpu(edge_serial->boot_descriptor.BuildNumber));
2782                 dev_dbg(dev, "  Capabilities:   0x%x\n",
2783                       le16_to_cpu(edge_serial->boot_descriptor.Capabilities));
2784                 dev_dbg(dev, "  UConfig0:       %d\n",
2785                         edge_serial->boot_descriptor.UConfig0);
2786                 dev_dbg(dev, "  UConfig1:       %d\n",
2787                         edge_serial->boot_descriptor.UConfig1);
2788         }
2789 }
2790
2791
2792 /****************************************************************************
2793  * load_application_firmware
2794  *      This is called to load the application firmware to the device
2795  ****************************************************************************/
2796 static void load_application_firmware(struct edgeport_serial *edge_serial)
2797 {
2798         struct device *dev = &edge_serial->serial->dev->dev;
2799         const struct ihex_binrec *rec;
2800         const struct firmware *fw;
2801         const char *fw_name;
2802         const char *fw_info;
2803         int response;
2804         __u32 Operaddr;
2805         __u16 build;
2806
2807         switch (edge_serial->product_info.iDownloadFile) {
2808                 case EDGE_DOWNLOAD_FILE_I930:
2809                         fw_info = "downloading firmware version (930)";
2810                         fw_name = "edgeport/down.fw";
2811                         break;
2812
2813                 case EDGE_DOWNLOAD_FILE_80251:
2814                         fw_info = "downloading firmware version (80251)";
2815                         fw_name = "edgeport/down2.fw";
2816                         break;
2817
2818                 case EDGE_DOWNLOAD_FILE_NONE:
2819                         dev_dbg(dev, "No download file specified, skipping download\n");
2820                         return;
2821
2822                 default:
2823                         return;
2824         }
2825
2826         response = request_ihex_firmware(&fw, fw_name,
2827                                     &edge_serial->serial->dev->dev);
2828         if (response) {
2829                 dev_err(dev, "Failed to load image \"%s\" err %d\n",
2830                        fw_name, response);
2831                 return;
2832         }
2833
2834         rec = (const struct ihex_binrec *)fw->data;
2835         build = (rec->data[2] << 8) | rec->data[3];
2836
2837         dev_dbg(dev, "%s %d.%d.%d\n", fw_info, rec->data[0], rec->data[1], build);
2838
2839         edge_serial->product_info.FirmwareMajorVersion = rec->data[0];
2840         edge_serial->product_info.FirmwareMinorVersion = rec->data[1];
2841         edge_serial->product_info.FirmwareBuildNumber = cpu_to_le16(build);
2842
2843         for (rec = ihex_next_binrec(rec); rec;
2844              rec = ihex_next_binrec(rec)) {
2845                 Operaddr = be32_to_cpu(rec->addr);
2846                 response = sram_write(edge_serial->serial,
2847                                      Operaddr >> 16,
2848                                      Operaddr & 0xFFFF,
2849                                      be16_to_cpu(rec->len),
2850                                      &rec->data[0]);
2851                 if (response < 0) {
2852                         dev_err(&edge_serial->serial->dev->dev,
2853                                 "sram_write failed (%x, %x, %d)\n",
2854                                 Operaddr >> 16, Operaddr & 0xFFFF,
2855                                 be16_to_cpu(rec->len));
2856                         break;
2857                 }
2858         }
2859
2860         dev_dbg(dev, "sending exec_dl_code\n");
2861         response = usb_control_msg (edge_serial->serial->dev,
2862                                     usb_sndctrlpipe(edge_serial->serial->dev, 0),
2863                                     USB_REQUEST_ION_EXEC_DL_CODE,
2864                                     0x40, 0x4000, 0x0001, NULL, 0, 3000);
2865
2866         release_firmware(fw);
2867 }
2868
2869
2870 /****************************************************************************
2871  * edge_startup
2872  ****************************************************************************/
2873 static int edge_startup(struct usb_serial *serial)
2874 {
2875         struct edgeport_serial *edge_serial;
2876         struct usb_device *dev;
2877         struct device *ddev = &serial->dev->dev;
2878         int i;
2879         int response;
2880         bool interrupt_in_found;
2881         bool bulk_in_found;
2882         bool bulk_out_found;
2883         static __u32 descriptor[3] = {  EDGE_COMPATIBILITY_MASK0,
2884                                         EDGE_COMPATIBILITY_MASK1,
2885                                         EDGE_COMPATIBILITY_MASK2 };
2886
2887         dev = serial->dev;
2888
2889         /* create our private serial structure */
2890         edge_serial = kzalloc(sizeof(struct edgeport_serial), GFP_KERNEL);
2891         if (edge_serial == NULL) {
2892                 dev_err(&serial->dev->dev, "%s - Out of memory\n", __func__);
2893                 return -ENOMEM;
2894         }
2895         spin_lock_init(&edge_serial->es_lock);
2896         edge_serial->serial = serial;
2897         usb_set_serial_data(serial, edge_serial);
2898
2899         /* get the name for the device from the device */
2900         i = usb_string(dev, dev->descriptor.iManufacturer,
2901             &edge_serial->name[0], MAX_NAME_LEN+1);
2902         if (i < 0)
2903                 i = 0;
2904         edge_serial->name[i++] = ' ';
2905         usb_string(dev, dev->descriptor.iProduct,
2906             &edge_serial->name[i], MAX_NAME_LEN+2 - i);
2907
2908         dev_info(&serial->dev->dev, "%s detected\n", edge_serial->name);
2909
2910         /* Read the epic descriptor */
2911         if (get_epic_descriptor(edge_serial) <= 0) {
2912                 /* memcpy descriptor to Supports structures */
2913                 memcpy(&edge_serial->epic_descriptor.Supports, descriptor,
2914                        sizeof(struct edge_compatibility_bits));
2915
2916                 /* get the manufacturing descriptor for this device */
2917                 get_manufacturing_desc(edge_serial);
2918
2919                 /* get the boot descriptor */
2920                 get_boot_desc(edge_serial);
2921
2922                 get_product_info(edge_serial);
2923         }
2924
2925         /* set the number of ports from the manufacturing description */
2926         /* serial->num_ports = serial->product_info.NumPorts; */
2927         if ((!edge_serial->is_epic) &&
2928             (edge_serial->product_info.NumPorts != serial->num_ports)) {
2929                 dev_warn(ddev,
2930                         "Device Reported %d serial ports vs. core thinking we have %d ports, email greg@kroah.com this information.\n",
2931                          edge_serial->product_info.NumPorts,
2932                          serial->num_ports);
2933         }
2934
2935         dev_dbg(ddev, "%s - time 1 %ld\n", __func__, jiffies);
2936
2937         /* If not an EPiC device */
2938         if (!edge_serial->is_epic) {
2939                 /* now load the application firmware into this device */
2940                 load_application_firmware(edge_serial);
2941
2942                 dev_dbg(ddev, "%s - time 2 %ld\n", __func__, jiffies);
2943
2944                 /* Check current Edgeport EEPROM and update if necessary */
2945                 update_edgeport_E2PROM(edge_serial);
2946
2947                 dev_dbg(ddev, "%s - time 3 %ld\n", __func__, jiffies);
2948
2949                 /* set the configuration to use #1 */
2950 /*              dev_dbg(ddev, "set_configuration 1\n"); */
2951 /*              usb_set_configuration (dev, 1); */
2952         }
2953         dev_dbg(ddev, "  FirmwareMajorVersion  %d.%d.%d\n",
2954             edge_serial->product_info.FirmwareMajorVersion,
2955             edge_serial->product_info.FirmwareMinorVersion,
2956             le16_to_cpu(edge_serial->product_info.FirmwareBuildNumber));
2957
2958         /* we set up the pointers to the endpoints in the edge_open function,
2959          * as the structures aren't created yet. */
2960
2961         response = 0;
2962
2963         if (edge_serial->is_epic) {
2964                 /* EPIC thing, set up our interrupt polling now and our read
2965                  * urb, so that the device knows it really is connected. */
2966                 interrupt_in_found = bulk_in_found = bulk_out_found = false;
2967                 for (i = 0; i < serial->interface->altsetting[0]
2968                                                 .desc.bNumEndpoints; ++i) {
2969                         struct usb_endpoint_descriptor *endpoint;
2970                         int buffer_size;
2971
2972                         endpoint = &serial->interface->altsetting[0].
2973                                                         endpoint[i].desc;
2974                         buffer_size = usb_endpoint_maxp(endpoint);
2975                         if (!interrupt_in_found &&
2976                             (usb_endpoint_is_int_in(endpoint))) {
2977                                 /* we found a interrupt in endpoint */
2978                                 dev_dbg(ddev, "found interrupt in\n");
2979
2980                                 /* not set up yet, so do it now */
2981                                 edge_serial->interrupt_read_urb =
2982                                                 usb_alloc_urb(0, GFP_KERNEL);
2983                                 if (!edge_serial->interrupt_read_urb) {
2984                                         dev_err(ddev, "out of memory\n");
2985                                         return -ENOMEM;
2986                                 }
2987                                 edge_serial->interrupt_in_buffer =
2988                                         kmalloc(buffer_size, GFP_KERNEL);
2989                                 if (!edge_serial->interrupt_in_buffer) {
2990                                         dev_err(ddev, "out of memory\n");
2991                                         usb_free_urb(edge_serial->interrupt_read_urb);
2992                                         return -ENOMEM;
2993                                 }
2994                                 edge_serial->interrupt_in_endpoint =
2995                                                 endpoint->bEndpointAddress;
2996
2997                                 /* set up our interrupt urb */
2998                                 usb_fill_int_urb(
2999                                         edge_serial->interrupt_read_urb,
3000                                         dev,
3001                                         usb_rcvintpipe(dev,
3002                                                 endpoint->bEndpointAddress),
3003                                         edge_serial->interrupt_in_buffer,
3004                                         buffer_size,
3005                                         edge_interrupt_callback,
3006                                         edge_serial,
3007                                         endpoint->bInterval);
3008
3009                                 interrupt_in_found = true;
3010                         }
3011
3012                         if (!bulk_in_found &&
3013                                 (usb_endpoint_is_bulk_in(endpoint))) {
3014                                 /* we found a bulk in endpoint */
3015                                 dev_dbg(ddev, "found bulk in\n");
3016
3017                                 /* not set up yet, so do it now */
3018                                 edge_serial->read_urb =
3019                                                 usb_alloc_urb(0, GFP_KERNEL);
3020                                 if (!edge_serial->read_urb) {
3021                                         dev_err(ddev, "out of memory\n");
3022                                         return -ENOMEM;
3023                                 }
3024                                 edge_serial->bulk_in_buffer =
3025                                         kmalloc(buffer_size, GFP_KERNEL);
3026                                 if (!edge_serial->bulk_in_buffer) {
3027                                         dev_err(&dev->dev, "out of memory\n");
3028                                         usb_free_urb(edge_serial->read_urb);
3029                                         return -ENOMEM;
3030                                 }
3031                                 edge_serial->bulk_in_endpoint =
3032                                                 endpoint->bEndpointAddress;
3033
3034                                 /* set up our bulk in urb */
3035                                 usb_fill_bulk_urb(edge_serial->read_urb, dev,
3036                                         usb_rcvbulkpipe(dev,
3037                                                 endpoint->bEndpointAddress),
3038                                         edge_serial->bulk_in_buffer,
3039                                         usb_endpoint_maxp(endpoint),
3040                                         edge_bulk_in_callback,
3041                                         edge_serial);
3042                                 bulk_in_found = true;
3043                         }
3044
3045                         if (!bulk_out_found &&
3046                             (usb_endpoint_is_bulk_out(endpoint))) {
3047                                 /* we found a bulk out endpoint */
3048                                 dev_dbg(ddev, "found bulk out\n");
3049                                 edge_serial->bulk_out_endpoint =
3050                                                 endpoint->bEndpointAddress;
3051                                 bulk_out_found = true;
3052                         }
3053                 }
3054
3055                 if (!interrupt_in_found || !bulk_in_found || !bulk_out_found) {
3056                         dev_err(ddev, "Error - the proper endpoints were not found!\n");
3057                         return -ENODEV;
3058                 }
3059
3060                 /* start interrupt read for this edgeport this interrupt will
3061                  * continue as long as the edgeport is connected */
3062                 response = usb_submit_urb(edge_serial->interrupt_read_urb,
3063                                                                 GFP_KERNEL);
3064                 if (response)
3065                         dev_err(ddev, "%s - Error %d submitting control urb\n",
3066                                 __func__, response);
3067         }
3068         return response;
3069 }
3070
3071
3072 /****************************************************************************
3073  * edge_disconnect
3074  *      This function is called whenever the device is removed from the usb bus.
3075  ****************************************************************************/
3076 static void edge_disconnect(struct usb_serial *serial)
3077 {
3078         struct edgeport_serial *edge_serial = usb_get_serial_data(serial);
3079
3080         /* stop reads and writes on all ports */
3081         /* free up our endpoint stuff */
3082         if (edge_serial->is_epic) {
3083                 usb_kill_urb(edge_serial->interrupt_read_urb);
3084                 usb_free_urb(edge_serial->interrupt_read_urb);
3085                 kfree(edge_serial->interrupt_in_buffer);
3086
3087                 usb_kill_urb(edge_serial->read_urb);
3088                 usb_free_urb(edge_serial->read_urb);
3089                 kfree(edge_serial->bulk_in_buffer);
3090         }
3091 }
3092
3093
3094 /****************************************************************************
3095  * edge_release
3096  *      This function is called when the device structure is deallocated.
3097  ****************************************************************************/
3098 static void edge_release(struct usb_serial *serial)
3099 {
3100         struct edgeport_serial *edge_serial = usb_get_serial_data(serial);
3101
3102         kfree(edge_serial);
3103 }
3104
3105 static int edge_port_probe(struct usb_serial_port *port)
3106 {
3107         struct edgeport_port *edge_port;
3108
3109         edge_port = kzalloc(sizeof(*edge_port), GFP_KERNEL);
3110         if (!edge_port)
3111                 return -ENOMEM;
3112
3113         spin_lock_init(&edge_port->ep_lock);
3114         edge_port->port = port;
3115
3116         usb_set_serial_port_data(port, edge_port);
3117
3118         return 0;
3119 }
3120
3121 static int edge_port_remove(struct usb_serial_port *port)
3122 {
3123         struct edgeport_port *edge_port;
3124
3125         edge_port = usb_get_serial_port_data(port);
3126         kfree(edge_port);
3127
3128         return 0;
3129 }
3130
3131 module_usb_serial_driver(serial_drivers, id_table_combined);
3132
3133 MODULE_AUTHOR(DRIVER_AUTHOR);
3134 MODULE_DESCRIPTION(DRIVER_DESC);
3135 MODULE_LICENSE("GPL");
3136 MODULE_FIRMWARE("edgeport/boot.fw");
3137 MODULE_FIRMWARE("edgeport/boot2.fw");
3138 MODULE_FIRMWARE("edgeport/down.fw");
3139 MODULE_FIRMWARE("edgeport/down2.fw");