2 * linux/include/linux/mmc/host.h
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
8 * Host driver specific definitions.
10 #ifndef LINUX_MMC_HOST_H
11 #define LINUX_MMC_HOST_H
13 #include <linux/leds.h>
14 #include <linux/sched.h>
15 #include <linux/wakelock.h>
17 #include <linux/mmc/core.h>
18 #include <linux/mmc/pm.h>
21 unsigned int clock; /* clock rate */
24 /* vdd stores the bit number of the selected voltage range from below. */
26 unsigned char bus_mode; /* command output mode */
28 #define MMC_BUSMODE_OPENDRAIN 1
29 #define MMC_BUSMODE_PUSHPULL 2
31 unsigned char chip_select; /* SPI chip select */
33 #define MMC_CS_DONTCARE 0
37 unsigned char power_mode; /* power supply mode */
39 #define MMC_POWER_OFF 0
40 #define MMC_POWER_UP 1
41 #define MMC_POWER_ON 2
43 unsigned char bus_width; /* data bus width */
45 #define MMC_BUS_WIDTH_1 0
46 #define MMC_BUS_WIDTH_4 2
47 #define MMC_BUS_WIDTH_8 3
49 unsigned char timing; /* timing specification used */
51 #define MMC_TIMING_LEGACY 0
52 #define MMC_TIMING_MMC_HS 1
53 #define MMC_TIMING_SD_HS 2
54 #define MMC_TIMING_UHS_SDR12 MMC_TIMING_LEGACY
55 #define MMC_TIMING_UHS_SDR25 MMC_TIMING_SD_HS
56 #define MMC_TIMING_UHS_SDR50 3
57 #define MMC_TIMING_UHS_SDR104 4
58 #define MMC_TIMING_UHS_DDR50 5
59 #define MMC_TIMING_MMC_HS200 8
61 unsigned char ddr; /* dual data rate used */
63 #define MMC_SDR_MODE 0
64 #define MMC_1_2V_DDR_MODE 1
65 #define MMC_1_8V_DDR_MODE 2
67 unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */
69 #define MMC_SIGNAL_VOLTAGE_330 0
70 #define MMC_SIGNAL_VOLTAGE_180 1
71 #define MMC_SIGNAL_VOLTAGE_120 2
73 unsigned char drv_type; /* driver type (A, B, C, D) */
75 #define MMC_SET_DRIVER_TYPE_B 0
76 #define MMC_SET_DRIVER_TYPE_A 1
77 #define MMC_SET_DRIVER_TYPE_C 2
78 #define MMC_SET_DRIVER_TYPE_D 3
83 * Hosts that support power saving can use the 'enable' and 'disable'
84 * methods to exit and enter power saving states. 'enable' is called
85 * when the host is claimed and 'disable' is called (or scheduled with
86 * a delay) when the host is released. The 'disable' is scheduled if
87 * the disable delay set by 'mmc_set_disable_delay()' is non-zero,
88 * otherwise 'disable' is called immediately. 'disable' may be
89 * scheduled repeatedly, to permit ever greater power saving at the
90 * expense of ever greater latency to re-enable. Rescheduling is
91 * determined by the return value of the 'disable' method. A positive
92 * value gives the delay in milliseconds.
94 * In the case where a host function (like set_ios) may be called
95 * with or without the host claimed, enabling and disabling can be
96 * done directly and will nest correctly. Call 'mmc_host_enable()' and
97 * 'mmc_host_lazy_disable()' for this purpose, but note that these
98 * functions must be paired.
100 * Alternatively, 'mmc_host_enable()' may be paired with
101 * 'mmc_host_disable()' which calls 'disable' immediately. In this
102 * case the 'disable' method will be called with 'lazy' set to 0.
103 * This is mainly useful for error paths.
105 * Because lazy disable may be called from a work queue, the 'disable'
106 * method must claim the host when 'lazy' != 0, which will work
107 * correctly because recursion is detected and handled.
109 int (*enable)(struct mmc_host *host);
110 int (*disable)(struct mmc_host *host, int lazy);
112 * It is optional for the host to implement pre_req and post_req in
113 * order to support double buffering of requests (prepare one
114 * request while another request is active).
116 void (*post_req)(struct mmc_host *host, struct mmc_request *req,
118 void (*pre_req)(struct mmc_host *host, struct mmc_request *req,
120 void (*request)(struct mmc_host *host, struct mmc_request *req);
122 * Avoid calling these three functions too often or in a "fast path",
123 * since underlaying controller might implement them in an expensive
126 * Also note that these functions might sleep, so don't call them
127 * in the atomic contexts!
129 * Return values for the get_ro callback should be:
130 * 0 for a read/write card
131 * 1 for a read-only card
132 * -ENOSYS when not supported (equal to NULL callback)
133 * or a negative errno value when something bad happened
135 * Return values for the get_cd callback should be:
136 * 0 for a absent card
137 * 1 for a present card
138 * -ENOSYS when not supported (equal to NULL callback)
139 * or a negative errno value when something bad happened
141 void (*set_ios)(struct mmc_host *host, struct mmc_ios *ios);
142 int (*get_ro)(struct mmc_host *host);
143 int (*get_cd)(struct mmc_host *host);
145 void (*enable_sdio_irq)(struct mmc_host *host, int enable);
147 /* optional callback for HC quirks */
148 void (*init_card)(struct mmc_host *host, struct mmc_card *card);
149 /* Check if the card is pulling dat[0:3] low */
150 int (*card_busy)(struct mmc_host *host);
152 int (*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv);
154 int (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios);
155 /* The tuning command opcode value is different for SD and eMMC cards */
156 int (*execute_tuning)(struct mmc_host *host,u32 opcode);
157 void (*enable_preset_value)(struct mmc_host *host, bool enable);
163 struct mmc_async_req {
164 /* active mmc request */
165 struct mmc_request *mrq;
167 * Check error status of completed mmc request.
168 * Returns 0 if success otherwise non zero.
170 int (*err_check) (struct mmc_card *, struct mmc_async_req *);
173 #define HOST_IS_EMMC(host) (host->unused)
176 struct device *parent;
177 struct device class_dev;
179 const struct mmc_host_ops *ops;
184 u32 ocr_avail_sdio; /* SDIO-specific OCR */
185 u32 ocr_avail_sd; /* SD-specific OCR */
186 u32 ocr_avail_mmc; /* MMC-specific OCR */
187 struct notifier_block pm_notify;
189 #define MMC_VDD_165_195 0x00000080 /* VDD voltage 1.65 - 1.95 */
190 #define MMC_VDD_20_21 0x00000100 /* VDD voltage 2.0 ~ 2.1 */
191 #define MMC_VDD_21_22 0x00000200 /* VDD voltage 2.1 ~ 2.2 */
192 #define MMC_VDD_22_23 0x00000400 /* VDD voltage 2.2 ~ 2.3 */
193 #define MMC_VDD_23_24 0x00000800 /* VDD voltage 2.3 ~ 2.4 */
194 #define MMC_VDD_24_25 0x00001000 /* VDD voltage 2.4 ~ 2.5 */
195 #define MMC_VDD_25_26 0x00002000 /* VDD voltage 2.5 ~ 2.6 */
196 #define MMC_VDD_26_27 0x00004000 /* VDD voltage 2.6 ~ 2.7 */
197 #define MMC_VDD_27_28 0x00008000 /* VDD voltage 2.7 ~ 2.8 */
198 #define MMC_VDD_28_29 0x00010000 /* VDD voltage 2.8 ~ 2.9 */
199 #define MMC_VDD_29_30 0x00020000 /* VDD voltage 2.9 ~ 3.0 */
200 #define MMC_VDD_30_31 0x00040000 /* VDD voltage 3.0 ~ 3.1 */
201 #define MMC_VDD_31_32 0x00080000 /* VDD voltage 3.1 ~ 3.2 */
202 #define MMC_VDD_32_33 0x00100000 /* VDD voltage 3.2 ~ 3.3 */
203 #define MMC_VDD_33_34 0x00200000 /* VDD voltage 3.3 ~ 3.4 */
204 #define MMC_VDD_34_35 0x00400000 /* VDD voltage 3.4 ~ 3.5 */
205 #define MMC_VDD_35_36 0x00800000 /* VDD voltage 3.5 ~ 3.6 */
207 unsigned long caps; /* Host capabilities */
209 #define MMC_CAP_4_BIT_DATA (1 << 0) /* Can the host do 4 bit transfers */
210 #define MMC_CAP_MMC_HIGHSPEED (1 << 1) /* Can do MMC high-speed timing */
211 #define MMC_CAP_SD_HIGHSPEED (1 << 2) /* Can do SD high-speed timing */
212 #define MMC_CAP_SDIO_IRQ (1 << 3) /* Can signal pending SDIO IRQs */
213 #define MMC_CAP_SPI (1 << 4) /* Talks only SPI protocols */
214 #define MMC_CAP_NEEDS_POLL (1 << 5) /* Needs polling for card-detection */
215 #define MMC_CAP_8_BIT_DATA (1 << 6) /* Can the host do 8 bit transfers */
216 #define MMC_CAP_DISABLE (1 << 7) /* Can the host be disabled */
217 #define MMC_CAP_NONREMOVABLE (1 << 8) /* Nonremovable e.g. eMMC */
218 #define MMC_CAP_WAIT_WHILE_BUSY (1 << 9) /* Waits while card is busy */
219 #define MMC_CAP_ERASE (1 << 10) /* Allow erase/trim commands */
220 #define MMC_CAP_1_8V_DDR (1 << 11) /* can support */
221 /* DDR mode at 1.8V */
222 #define MMC_CAP_1_2V_DDR (1 << 12) /* can support */
223 /* DDR mode at 1.2V */
224 #define MMC_CAP_POWER_OFF_CARD (1 << 13) /* Can power off after boot */
225 #define MMC_CAP_BUS_WIDTH_TEST (1 << 14) /* CMD14/CMD19 bus width ok */
226 #define MMC_CAP_UHS_SDR12 (1 << 15) /* Host supports UHS SDR12 mode */
227 #define MMC_CAP_UHS_SDR25 (1 << 16) /* Host supports UHS SDR25 mode */
228 #define MMC_CAP_UHS_SDR50 (1 << 17) /* Host supports UHS SDR50 mode */
229 #define MMC_CAP_UHS_SDR104 (1 << 18) /* Host supports UHS SDR104 mode */
230 #define MMC_CAP_UHS_DDR50 (1 << 19) /* Host supports UHS DDR50 mode */
231 #define MMC_CAP_SET_XPC_330 (1 << 20) /* Host supports >150mA current at 3.3V */
232 #define MMC_CAP_SET_XPC_300 (1 << 21) /* Host supports >150mA current at 3.0V */
233 #define MMC_CAP_SET_XPC_180 (1 << 22) /* Host supports >150mA current at 1.8V */
234 #define MMC_CAP_DRIVER_TYPE_A (1 << 23) /* Host supports Driver Type A */
235 #define MMC_CAP_DRIVER_TYPE_C (1 << 24) /* Host supports Driver Type C */
236 #define MMC_CAP_DRIVER_TYPE_D (1 << 25) /* Host supports Driver Type D */
237 #define MMC_CAP_MAX_CURRENT_200 (1 << 26) /* Host max current limit is 200mA */
238 #define MMC_CAP_MAX_CURRENT_400 (1 << 27) /* Host max current limit is 400mA */
239 #define MMC_CAP_MAX_CURRENT_600 (1 << 28) /* Host max current limit is 600mA */
240 #define MMC_CAP_MAX_CURRENT_800 (1 << 29) /* Host max current limit is 800mA */
241 #define MMC_CAP_CMD23 (1 << 30) /* CMD23 supported. */
242 #define MMC_CAP_HW_RESET (1 << 31) /* Hardware reset */
244 u32 caps2; /* More host capabilities */
245 #define MMC_CAP2_BOOTPART_NOACC (1 << 0) /* Boot partition no access */
246 #define MMC_CAP2_CACHE_CTRL (1 << 1) /* Allow cache control */
247 #define MMC_CAP2_POWEROFF_NOTIFY (1 << 2) /* Notify poweroff supported */
248 #define MMC_CAP2_NO_MULTI_READ (1 << 3) /* Multiblock reads don't work */
249 #define MMC_CAP2_NO_SLEEP_CMD (1 << 4) /* Don't allow sleep command */
250 #define MMC_CAP2_HS200_1_8V_SDR (1 << 5) /* can support */
251 #define MMC_CAP2_HS200_1_2V_SDR (1 << 6) /* can support */
252 #define MMC_CAP2_HS200 (MMC_CAP2_HS200_1_8V_SDR | \
253 MMC_CAP2_HS200_1_2V_SDR)
254 #define MMC_CAP2_BROKEN_VOLTAGE (1 << 7) /* Use the broken voltage */
255 #define MMC_CAP2_DETECT_ON_ERR (1 << 8) /* On I/O err check card removal */
256 #define MMC_CAP2_HC_ERASE_SZ (1 << 9) /* High-capacity erase size */
257 #define MMC_CAP2_CD_ACTIVE_HIGH (1 << 10) /* Card-detect signal active high */
258 #define MMC_CAP2_RO_ACTIVE_HIGH (1 << 11) /* Write-protect signal active high */
259 #define MMC_CAP2_PACKED_RD (1 << 12) /* Allow packed read */
260 #define MMC_CAP2_PACKED_WR (1 << 13) /* Allow packed write */
261 #define MMC_CAP2_PACKED_CMD (MMC_CAP2_PACKED_RD | \
263 #define MMC_CAP2_NO_PRESCAN_POWERUP (1 << 14) /* Don't power up before scan */
265 mmc_pm_flag_t pm_caps; /* supported pm features */
267 #ifdef CONFIG_MMC_CLKGATE
268 int clk_requests; /* internal reference counter */
269 unsigned int clk_delay; /* number of MCI clk hold cycles */
270 bool clk_gated; /* clock gated */
271 struct work_struct clk_gate_work; /* delayed clock gate */
272 unsigned int clk_old; /* old clock value cache */
273 spinlock_t clk_lock; /* lock for clk fields */
274 struct mutex clk_gate_mutex; /* mutex for clock gating */
277 /* host specific block data */
278 unsigned int max_seg_size; /* see blk_queue_max_segment_size */
279 unsigned short max_segs; /* see blk_queue_max_segments */
280 unsigned short unused;
281 unsigned int max_req_size; /* maximum number of bytes in one req */
282 unsigned int max_blk_size; /* maximum size of one mmc block */
283 unsigned int max_blk_count; /* maximum number of blocks in one req */
284 unsigned int max_discard_to; /* max. discard timeout in ms */
287 spinlock_t lock; /* lock for claim and bus ops */
289 struct mmc_ios ios; /* current io bus settings */
290 u32 ocr; /* the current OCR setting */
292 /* group bitfields together to minimize padding */
293 unsigned int use_spi_crc:1;
294 unsigned int claimed:1; /* host exclusively claimed */
295 unsigned int bus_dead:1; /* bus has been released */
296 #ifdef CONFIG_MMC_DEBUG
297 unsigned int removed:1; /* host is being removed */
300 /* Only used with MMC_CAP_DISABLE */
301 int enabled; /* host is enabled */
302 int rescan_disable; /* disable card detection */
303 int nesting_cnt; /* "enable" nesting count */
304 int en_dis_recurs; /* detect recursion */
305 unsigned int disable_delay; /* disable delay in msecs */
306 struct delayed_work disable; /* disabling work */
308 struct mmc_card *card; /* device attached to this host */
310 wait_queue_head_t wq;
311 struct task_struct *claimer; /* task that has host claimed */
312 int claim_cnt; /* "claim" nesting count */
314 struct delayed_work detect;
315 struct wake_lock detect_wake_lock;
317 const struct mmc_bus_ops *bus_ops; /* current bus driver */
318 unsigned int bus_refs; /* reference counter */
320 #if defined(CONFIG_SDMMC_RK29) && !defined(CONFIG_SDMMC_RK29_OLD)
321 unsigned int re_initialized_flags; //in order to begin the rescan ; added by xbw@2011-04-07
322 unsigned int doneflag; //added by xbw at 2011-08-27
323 int (*sdmmc_host_hw_init)(void *data);
326 unsigned int bus_resume_flags;
327 #define MMC_BUSRESUME_MANUAL_RESUME (1 << 0)
328 #define MMC_BUSRESUME_NEEDS_RESUME (1 << 1)
330 unsigned int sdio_irqs;
331 struct task_struct *sdio_irq_thread;
332 bool sdio_irq_pending;
333 atomic_t sdio_irq_thread_abort;
335 mmc_pm_flag_t pm_flags; /* requested pm features */
337 #ifdef CONFIG_LEDS_TRIGGERS
338 struct led_trigger *led; /* activity led */
341 #ifdef CONFIG_REGULATOR
342 bool regulator_enabled; /* regulator state */
345 struct dentry *debugfs_root;
347 #ifdef CONFIG_MMC_EMBEDDED_SDIO
349 struct sdio_cis *cis;
350 struct sdio_cccr *cccr;
351 struct sdio_embedded_func *funcs;
353 } embedded_sdio_data;
355 struct mmc_async_req *areq; /* active async req */
357 unsigned long private[0] ____cacheline_aligned;
360 extern struct mmc_host *mmc_alloc_host(int extra, struct device *);
361 extern int mmc_add_host(struct mmc_host *);
362 extern void mmc_remove_host(struct mmc_host *);
363 extern void mmc_free_host(struct mmc_host *);
365 #ifdef CONFIG_MMC_EMBEDDED_SDIO
366 extern void mmc_set_embedded_sdio_data(struct mmc_host *host,
367 struct sdio_cis *cis,
368 struct sdio_cccr *cccr,
369 struct sdio_embedded_func *funcs,
373 static inline void *mmc_priv(struct mmc_host *host)
375 return (void *)host->private;
378 #define mmc_host_is_spi(host) ((host)->caps & MMC_CAP_SPI)
380 #define mmc_dev(x) ((x)->parent)
381 #define mmc_classdev(x) (&(x)->class_dev)
382 #define mmc_hostname(x) (dev_name(&(x)->class_dev))
383 #define mmc_bus_needs_resume(host) ((host)->bus_resume_flags & MMC_BUSRESUME_NEEDS_RESUME)
384 #define mmc_bus_manual_resume(host) ((host)->bus_resume_flags & MMC_BUSRESUME_MANUAL_RESUME)
386 static inline void mmc_set_bus_resume_policy(struct mmc_host *host, int manual)
389 host->bus_resume_flags |= MMC_BUSRESUME_MANUAL_RESUME;
391 host->bus_resume_flags &= ~MMC_BUSRESUME_MANUAL_RESUME;
394 extern int mmc_resume_bus(struct mmc_host *host);
396 extern int mmc_suspend_host(struct mmc_host *);
397 extern int mmc_resume_host(struct mmc_host *);
399 extern int mmc_power_save_host(struct mmc_host *host);
400 extern int mmc_power_restore_host(struct mmc_host *host);
402 extern void mmc_detect_change(struct mmc_host *, unsigned long delay);
403 extern void mmc_request_done(struct mmc_host *, struct mmc_request *);
405 static inline void mmc_signal_sdio_irq(struct mmc_host *host)
407 host->ops->enable_sdio_irq(host, 0);
408 host->sdio_irq_pending = true;
409 wake_up_process(host->sdio_irq_thread);
414 #ifdef CONFIG_REGULATOR
415 int mmc_regulator_get_ocrmask(struct regulator *supply);
416 int mmc_regulator_set_ocr(struct mmc_host *mmc,
417 struct regulator *supply,
418 unsigned short vdd_bit);
420 static inline int mmc_regulator_get_ocrmask(struct regulator *supply)
425 static inline int mmc_regulator_set_ocr(struct mmc_host *mmc,
426 struct regulator *supply,
427 unsigned short vdd_bit)
433 int mmc_card_awake(struct mmc_host *host);
434 int mmc_card_sleep(struct mmc_host *host);
435 int mmc_card_can_sleep(struct mmc_host *host);
437 int mmc_host_enable(struct mmc_host *host);
438 int mmc_host_disable(struct mmc_host *host);
439 int mmc_host_lazy_disable(struct mmc_host *host);
440 int mmc_pm_notify(struct notifier_block *notify_block, unsigned long, void *);
442 static inline void mmc_set_disable_delay(struct mmc_host *host,
443 unsigned int disable_delay)
445 host->disable_delay = disable_delay;
448 /* Module parameter */
449 extern int mmc_assume_removable;
451 static inline int mmc_card_is_removable(struct mmc_host *host)
453 return !(host->caps & MMC_CAP_NONREMOVABLE) && mmc_assume_removable;
456 static inline int mmc_card_keep_power(struct mmc_host *host)
458 return host->pm_flags & MMC_PM_KEEP_POWER;
461 static inline int mmc_card_wake_sdio_irq(struct mmc_host *host)
463 return host->pm_flags & MMC_PM_WAKE_SDIO_IRQ;
466 static inline int mmc_host_cmd23(struct mmc_host *host)
468 return host->caps & MMC_CAP_CMD23;
471 static inline int mmc_host_uhs(struct mmc_host *host)
474 (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
475 MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 |