4 * We call the USB code inside a Linux-based peripheral device a "gadget"
5 * driver, except for the hardware-specific bus glue. One USB host can
6 * master many USB gadgets, but the gadgets are only slaved to one host.
9 * (C) Copyright 2002-2004 by David Brownell
10 * All Rights Reserved.
12 * This software is licensed under the GNU GPL version 2.
15 #ifndef __LINUX_USB_GADGET_H
16 #define __LINUX_USB_GADGET_H
18 #include <linux/device.h>
19 #include <linux/errno.h>
20 #include <linux/init.h>
21 #include <linux/list.h>
22 #include <linux/slab.h>
23 #include <linux/scatterlist.h>
24 #include <linux/types.h>
25 #include <linux/workqueue.h>
26 #include <linux/usb/ch9.h>
31 * struct usb_request - describes one i/o request
32 * @buf: Buffer used for data. Always provide this; some controllers
33 * only use PIO, or don't use DMA for some endpoints.
34 * @dma: DMA address corresponding to 'buf'. If you don't set this
35 * field, and the usb controller needs one, it is responsible
36 * for mapping and unmapping the buffer.
37 * @sg: a scatterlist for SG-capable controllers.
38 * @num_sgs: number of SG entries
39 * @num_mapped_sgs: number of SG entries mapped to DMA (internal)
40 * @length: Length of that data
41 * @stream_id: The stream id, when USB3.0 bulk streams are being used
42 * @no_interrupt: If true, hints that no completion irq is needed.
43 * Helpful sometimes with deep request queues that are handled
44 * directly by DMA controllers.
45 * @zero: If true, when writing data, makes the last packet be "short"
46 * by adding a zero length packet as needed;
47 * @short_not_ok: When reading data, makes short packets be
48 * treated as errors (queue stops advancing till cleanup).
49 * @complete: Function called when request completes, so this request and
50 * its buffer may be re-used. The function will always be called with
51 * interrupts disabled, and it must not sleep.
52 * Reads terminate with a short packet, or when the buffer fills,
53 * whichever comes first. When writes terminate, some data bytes
54 * will usually still be in flight (often in a hardware fifo).
55 * Errors (for reads or writes) stop the queue from advancing
56 * until the completion function returns, so that any transfers
57 * invalidated by the error may first be dequeued.
58 * @context: For use by the completion callback
59 * @list: For use by the gadget driver.
60 * @status: Reports completion code, zero or a negative errno.
61 * Normally, faults block the transfer queue from advancing until
62 * the completion callback returns.
63 * Code "-ESHUTDOWN" indicates completion caused by device disconnect,
64 * or when the driver disabled the endpoint.
65 * @actual: Reports bytes transferred to/from the buffer. For reads (OUT
66 * transfers) this may be less than the requested length. If the
67 * short_not_ok flag is set, short reads are treated as errors
68 * even when status otherwise indicates successful completion.
69 * Note that for writes (IN transfers) some data bytes may still
70 * reside in a device-side FIFO when the request is reported as
73 * These are allocated/freed through the endpoint they're used with. The
74 * hardware's driver can add extra per-request data to the memory it returns,
75 * which often avoids separate memory allocations (potential failures),
76 * later when the request is queued.
78 * Request flags affect request handling, such as whether a zero length
79 * packet is written (the "zero" flag), whether a short read should be
80 * treated as an error (blocking request queue advance, the "short_not_ok"
81 * flag), or hinting that an interrupt is not required (the "no_interrupt"
82 * flag, for use with deep request queues).
84 * Bulk endpoints can use any size buffers, and can also be used for interrupt
85 * transfers. interrupt-only endpoints can be much less functional.
87 * NOTE: this is analogous to 'struct urb' on the host side, except that
88 * it's thinner and promotes more pre-allocation.
96 struct scatterlist *sg;
98 unsigned num_mapped_sgs;
100 unsigned stream_id:16;
101 unsigned no_interrupt:1;
103 unsigned short_not_ok:1;
105 void (*complete)(struct usb_ep *ep,
106 struct usb_request *req);
108 struct list_head list;
114 /*-------------------------------------------------------------------------*/
116 /* endpoint-specific parts of the api to the usb controller hardware.
117 * unlike the urb model, (de)multiplexing layers are not required.
118 * (so this api could slash overhead if used on the host side...)
120 * note that device side usb controllers commonly differ in how many
121 * endpoints they support, as well as their capabilities.
124 int (*enable) (struct usb_ep *ep,
125 const struct usb_endpoint_descriptor *desc);
126 int (*disable) (struct usb_ep *ep);
128 struct usb_request *(*alloc_request) (struct usb_ep *ep,
130 void (*free_request) (struct usb_ep *ep, struct usb_request *req);
132 int (*queue) (struct usb_ep *ep, struct usb_request *req,
134 int (*dequeue) (struct usb_ep *ep, struct usb_request *req);
136 int (*set_halt) (struct usb_ep *ep, int value);
137 int (*set_wedge) (struct usb_ep *ep);
139 int (*fifo_status) (struct usb_ep *ep);
140 void (*fifo_flush) (struct usb_ep *ep);
144 * struct usb_ep_caps - endpoint capabilities description
145 * @type_control:Endpoint supports control type (reserved for ep0).
146 * @type_iso:Endpoint supports isochronous transfers.
147 * @type_bulk:Endpoint supports bulk transfers.
148 * @type_int:Endpoint supports interrupt transfers.
149 * @dir_in:Endpoint supports IN direction.
150 * @dir_out:Endpoint supports OUT direction.
153 unsigned type_control:1;
155 unsigned type_bulk:1;
161 #define USB_EP_CAPS_TYPE_CONTROL 0x01
162 #define USB_EP_CAPS_TYPE_ISO 0x02
163 #define USB_EP_CAPS_TYPE_BULK 0x04
164 #define USB_EP_CAPS_TYPE_INT 0x08
165 #define USB_EP_CAPS_TYPE_ALL \
166 (USB_EP_CAPS_TYPE_ISO | USB_EP_CAPS_TYPE_BULK | USB_EP_CAPS_TYPE_INT)
167 #define USB_EP_CAPS_DIR_IN 0x01
168 #define USB_EP_CAPS_DIR_OUT 0x02
169 #define USB_EP_CAPS_DIR_ALL (USB_EP_CAPS_DIR_IN | USB_EP_CAPS_DIR_OUT)
171 #define USB_EP_CAPS(_type, _dir) \
173 .type_control = !!(_type & USB_EP_CAPS_TYPE_CONTROL), \
174 .type_iso = !!(_type & USB_EP_CAPS_TYPE_ISO), \
175 .type_bulk = !!(_type & USB_EP_CAPS_TYPE_BULK), \
176 .type_int = !!(_type & USB_EP_CAPS_TYPE_INT), \
177 .dir_in = !!(_dir & USB_EP_CAPS_DIR_IN), \
178 .dir_out = !!(_dir & USB_EP_CAPS_DIR_OUT), \
182 * struct usb_ep - device side representation of USB endpoint
183 * @name:identifier for the endpoint, such as "ep-a" or "ep9in-bulk"
184 * @ops: Function pointers used to access hardware-specific operations.
185 * @ep_list:the gadget's ep_list holds all of its endpoints
186 * @caps:The structure describing types and directions supported by endoint.
187 * @maxpacket:The maximum packet size used on this endpoint. The initial
188 * value can sometimes be reduced (hardware allowing), according to
189 * the endpoint descriptor used to configure the endpoint.
190 * @maxpacket_limit:The maximum packet size value which can be handled by this
191 * endpoint. It's set once by UDC driver when endpoint is initialized, and
192 * should not be changed. Should not be confused with maxpacket.
193 * @max_streams: The maximum number of streams supported
194 * by this EP (0 - 16, actual number is 2^n)
195 * @mult: multiplier, 'mult' value for SS Isoc EPs
196 * @maxburst: the maximum number of bursts supported by this EP (for usb3)
197 * @driver_data:for use by the gadget driver.
198 * @address: used to identify the endpoint when finding descriptor that
199 * matches connection speed
200 * @desc: endpoint descriptor. This pointer is set before the endpoint is
201 * enabled and remains valid until the endpoint is disabled.
202 * @comp_desc: In case of SuperSpeed support, this is the endpoint companion
203 * descriptor that is used to configure the endpoint
205 * the bus controller driver lists all the general purpose endpoints in
206 * gadget->ep_list. the control endpoint (gadget->ep0) is not in that list,
207 * and is accessed only in response to a driver setup() callback.
214 const struct usb_ep_ops *ops;
215 struct list_head ep_list;
216 struct usb_ep_caps caps;
219 unsigned maxpacket:16;
220 unsigned maxpacket_limit:16;
221 unsigned max_streams:16;
225 const struct usb_endpoint_descriptor *desc;
226 const struct usb_ss_ep_comp_descriptor *comp_desc;
229 /*-------------------------------------------------------------------------*/
232 * usb_ep_set_maxpacket_limit - set maximum packet size limit for endpoint
233 * @ep:the endpoint being configured
234 * @maxpacket_limit:value of maximum packet size limit
236 * This function should be used only in UDC drivers to initialize endpoint
237 * (usually in probe function).
239 static inline void usb_ep_set_maxpacket_limit(struct usb_ep *ep,
240 unsigned maxpacket_limit)
242 ep->maxpacket_limit = maxpacket_limit;
243 ep->maxpacket = maxpacket_limit;
247 * usb_ep_enable - configure endpoint, making it usable
248 * @ep:the endpoint being configured. may not be the endpoint named "ep0".
249 * drivers discover endpoints through the ep_list of a usb_gadget.
251 * When configurations are set, or when interface settings change, the driver
252 * will enable or disable the relevant endpoints. while it is enabled, an
253 * endpoint may be used for i/o until the driver receives a disconnect() from
254 * the host or until the endpoint is disabled.
256 * the ep0 implementation (which calls this routine) must ensure that the
257 * hardware capabilities of each endpoint match the descriptor provided
258 * for it. for example, an endpoint named "ep2in-bulk" would be usable
259 * for interrupt transfers as well as bulk, but it likely couldn't be used
260 * for iso transfers or for endpoint 14. some endpoints are fully
261 * configurable, with more generic names like "ep-a". (remember that for
262 * USB, "in" means "towards the USB master".)
264 * returns zero, or a negative error code.
266 static inline int usb_ep_enable(struct usb_ep *ep)
273 ret = ep->ops->enable(ep, ep->desc);
283 * usb_ep_disable - endpoint is no longer usable
284 * @ep:the endpoint being unconfigured. may not be the endpoint named "ep0".
286 * no other task may be using this endpoint when this is called.
287 * any pending and uncompleted requests will complete with status
288 * indicating disconnect (-ESHUTDOWN) before this call returns.
289 * gadget drivers must call usb_ep_enable() again before queueing
290 * requests to the endpoint.
292 * returns zero, or a negative error code.
294 static inline int usb_ep_disable(struct usb_ep *ep)
301 ret = ep->ops->disable(ep);
311 * usb_ep_alloc_request - allocate a request object to use with this endpoint
312 * @ep:the endpoint to be used with with the request
313 * @gfp_flags:GFP_* flags to use
315 * Request objects must be allocated with this call, since they normally
316 * need controller-specific setup and may even need endpoint-specific
317 * resources such as allocation of DMA descriptors.
318 * Requests may be submitted with usb_ep_queue(), and receive a single
319 * completion callback. Free requests with usb_ep_free_request(), when
320 * they are no longer needed.
322 * Returns the request, or null if one could not be allocated.
324 static inline struct usb_request *usb_ep_alloc_request(struct usb_ep *ep,
327 return ep->ops->alloc_request(ep, gfp_flags);
331 * usb_ep_free_request - frees a request object
332 * @ep:the endpoint associated with the request
333 * @req:the request being freed
335 * Reverses the effect of usb_ep_alloc_request().
336 * Caller guarantees the request is not queued, and that it will
337 * no longer be requeued (or otherwise used).
339 static inline void usb_ep_free_request(struct usb_ep *ep,
340 struct usb_request *req)
342 ep->ops->free_request(ep, req);
346 * usb_ep_queue - queues (submits) an I/O request to an endpoint.
347 * @ep:the endpoint associated with the request
348 * @req:the request being submitted
349 * @gfp_flags: GFP_* flags to use in case the lower level driver couldn't
350 * pre-allocate all necessary memory with the request.
352 * This tells the device controller to perform the specified request through
353 * that endpoint (reading or writing a buffer). When the request completes,
354 * including being canceled by usb_ep_dequeue(), the request's completion
355 * routine is called to return the request to the driver. Any endpoint
356 * (except control endpoints like ep0) may have more than one transfer
357 * request queued; they complete in FIFO order. Once a gadget driver
358 * submits a request, that request may not be examined or modified until it
359 * is given back to that driver through the completion callback.
361 * Each request is turned into one or more packets. The controller driver
362 * never merges adjacent requests into the same packet. OUT transfers
363 * will sometimes use data that's already buffered in the hardware.
364 * Drivers can rely on the fact that the first byte of the request's buffer
365 * always corresponds to the first byte of some USB packet, for both
366 * IN and OUT transfers.
368 * Bulk endpoints can queue any amount of data; the transfer is packetized
369 * automatically. The last packet will be short if the request doesn't fill it
370 * out completely. Zero length packets (ZLPs) should be avoided in portable
371 * protocols since not all usb hardware can successfully handle zero length
372 * packets. (ZLPs may be explicitly written, and may be implicitly written if
373 * the request 'zero' flag is set.) Bulk endpoints may also be used
374 * for interrupt transfers; but the reverse is not true, and some endpoints
375 * won't support every interrupt transfer. (Such as 768 byte packets.)
377 * Interrupt-only endpoints are less functional than bulk endpoints, for
378 * example by not supporting queueing or not handling buffers that are
379 * larger than the endpoint's maxpacket size. They may also treat data
380 * toggle differently.
382 * Control endpoints ... after getting a setup() callback, the driver queues
383 * one response (even if it would be zero length). That enables the
384 * status ack, after transferring data as specified in the response. Setup
385 * functions may return negative error codes to generate protocol stalls.
386 * (Note that some USB device controllers disallow protocol stall responses
387 * in some cases.) When control responses are deferred (the response is
388 * written after the setup callback returns), then usb_ep_set_halt() may be
389 * used on ep0 to trigger protocol stalls. Depending on the controller,
390 * it may not be possible to trigger a status-stage protocol stall when the
391 * data stage is over, that is, from within the response's completion
394 * For periodic endpoints, like interrupt or isochronous ones, the usb host
395 * arranges to poll once per interval, and the gadget driver usually will
396 * have queued some data to transfer at that time.
398 * Returns zero, or a negative error code. Endpoints that are not enabled
399 * report errors; errors will also be
400 * reported when the usb peripheral is disconnected.
402 static inline int usb_ep_queue(struct usb_ep *ep,
403 struct usb_request *req, gfp_t gfp_flags)
405 return ep->ops->queue(ep, req, gfp_flags);
409 * usb_ep_dequeue - dequeues (cancels, unlinks) an I/O request from an endpoint
410 * @ep:the endpoint associated with the request
411 * @req:the request being canceled
413 * If the request is still active on the endpoint, it is dequeued and its
414 * completion routine is called (with status -ECONNRESET); else a negative
415 * error code is returned. This is guaranteed to happen before the call to
416 * usb_ep_dequeue() returns.
418 * Note that some hardware can't clear out write fifos (to unlink the request
419 * at the head of the queue) except as part of disconnecting from usb. Such
420 * restrictions prevent drivers from supporting configuration changes,
421 * even to configuration zero (a "chapter 9" requirement).
423 static inline int usb_ep_dequeue(struct usb_ep *ep, struct usb_request *req)
425 return ep->ops->dequeue(ep, req);
429 * usb_ep_set_halt - sets the endpoint halt feature.
430 * @ep: the non-isochronous endpoint being stalled
432 * Use this to stall an endpoint, perhaps as an error report.
433 * Except for control endpoints,
434 * the endpoint stays halted (will not stream any data) until the host
435 * clears this feature; drivers may need to empty the endpoint's request
436 * queue first, to make sure no inappropriate transfers happen.
438 * Note that while an endpoint CLEAR_FEATURE will be invisible to the
439 * gadget driver, a SET_INTERFACE will not be. To reset endpoints for the
440 * current altsetting, see usb_ep_clear_halt(). When switching altsettings,
441 * it's simplest to use usb_ep_enable() or usb_ep_disable() for the endpoints.
443 * Returns zero, or a negative error code. On success, this call sets
444 * underlying hardware state that blocks data transfers.
445 * Attempts to halt IN endpoints will fail (returning -EAGAIN) if any
446 * transfer requests are still queued, or if the controller hardware
447 * (usually a FIFO) still holds bytes that the host hasn't collected.
449 static inline int usb_ep_set_halt(struct usb_ep *ep)
451 return ep->ops->set_halt(ep, 1);
455 * usb_ep_clear_halt - clears endpoint halt, and resets toggle
456 * @ep:the bulk or interrupt endpoint being reset
458 * Use this when responding to the standard usb "set interface" request,
459 * for endpoints that aren't reconfigured, after clearing any other state
460 * in the endpoint's i/o queue.
462 * Returns zero, or a negative error code. On success, this call clears
463 * the underlying hardware state reflecting endpoint halt and data toggle.
464 * Note that some hardware can't support this request (like pxa2xx_udc),
465 * and accordingly can't correctly implement interface altsettings.
467 static inline int usb_ep_clear_halt(struct usb_ep *ep)
469 return ep->ops->set_halt(ep, 0);
473 * usb_ep_set_wedge - sets the halt feature and ignores clear requests
474 * @ep: the endpoint being wedged
476 * Use this to stall an endpoint and ignore CLEAR_FEATURE(HALT_ENDPOINT)
477 * requests. If the gadget driver clears the halt status, it will
478 * automatically unwedge the endpoint.
480 * Returns zero on success, else negative errno.
483 usb_ep_set_wedge(struct usb_ep *ep)
485 if (ep->ops->set_wedge)
486 return ep->ops->set_wedge(ep);
488 return ep->ops->set_halt(ep, 1);
492 * usb_ep_fifo_status - returns number of bytes in fifo, or error
493 * @ep: the endpoint whose fifo status is being checked.
495 * FIFO endpoints may have "unclaimed data" in them in certain cases,
496 * such as after aborted transfers. Hosts may not have collected all
497 * the IN data written by the gadget driver (and reported by a request
498 * completion). The gadget driver may not have collected all the data
499 * written OUT to it by the host. Drivers that need precise handling for
500 * fault reporting or recovery may need to use this call.
502 * This returns the number of such bytes in the fifo, or a negative
503 * errno if the endpoint doesn't use a FIFO or doesn't support such
506 static inline int usb_ep_fifo_status(struct usb_ep *ep)
508 if (ep->ops->fifo_status)
509 return ep->ops->fifo_status(ep);
515 * usb_ep_fifo_flush - flushes contents of a fifo
516 * @ep: the endpoint whose fifo is being flushed.
518 * This call may be used to flush the "unclaimed data" that may exist in
519 * an endpoint fifo after abnormal transaction terminations. The call
520 * must never be used except when endpoint is not being used for any
521 * protocol translation.
523 static inline void usb_ep_fifo_flush(struct usb_ep *ep)
525 if (ep->ops->fifo_flush)
526 ep->ops->fifo_flush(ep);
530 /*-------------------------------------------------------------------------*/
532 struct usb_dcd_config_params {
533 __u8 bU1devExitLat; /* U1 Device exit Latency */
534 #define USB_DEFAULT_U1_DEV_EXIT_LAT 0x01 /* Less then 1 microsec */
535 __le16 bU2DevExitLat; /* U2 Device exit Latency */
536 #define USB_DEFAULT_U2_DEV_EXIT_LAT 0x1F4 /* Less then 500 microsec */
541 struct usb_gadget_driver;
544 /* the rest of the api to the controller hardware: device operations,
545 * which don't involve endpoints (or i/o).
547 struct usb_gadget_ops {
548 int (*get_frame)(struct usb_gadget *);
549 int (*wakeup)(struct usb_gadget *);
550 int (*set_selfpowered) (struct usb_gadget *, int is_selfpowered);
551 int (*vbus_session) (struct usb_gadget *, int is_active);
552 int (*vbus_draw) (struct usb_gadget *, unsigned mA);
553 int (*pullup) (struct usb_gadget *, int is_on);
554 int (*ioctl)(struct usb_gadget *,
555 unsigned code, unsigned long param);
556 void (*get_config_params)(struct usb_dcd_config_params *);
557 int (*udc_start)(struct usb_gadget *,
558 struct usb_gadget_driver *);
559 int (*udc_stop)(struct usb_gadget *);
560 struct usb_ep *(*match_ep)(struct usb_gadget *,
561 struct usb_endpoint_descriptor *,
562 struct usb_ss_ep_comp_descriptor *);
566 * struct usb_gadget - represents a usb slave device
567 * @work: (internal use) Workqueue to be used for sysfs_notify()
568 * @udc: struct usb_udc pointer for this gadget
569 * @ops: Function pointers used to access hardware-specific operations.
570 * @ep0: Endpoint zero, used when reading or writing responses to
571 * driver setup() requests
572 * @ep_list: List of other endpoints supported by the device.
573 * @speed: Speed of current connection to USB host.
574 * @max_speed: Maximal speed the UDC can handle. UDC must support this
575 * and all slower speeds.
576 * @state: the state we are now (attached, suspended, configured, etc)
577 * @name: Identifies the controller hardware type. Used in diagnostics
578 * and sometimes configuration.
579 * @dev: Driver model state for this abstract device.
580 * @out_epnum: last used out ep number
581 * @in_epnum: last used in ep number
582 * @otg_caps: OTG capabilities of this gadget.
583 * @sg_supported: true if we can handle scatter-gather
584 * @is_otg: True if the USB device port uses a Mini-AB jack, so that the
585 * gadget driver must provide a USB OTG descriptor.
586 * @is_a_peripheral: False unless is_otg, the "A" end of a USB cable
587 * is in the Mini-AB jack, and HNP has been used to switch roles
588 * so that the "A" device currently acts as A-Peripheral, not A-Host.
589 * @a_hnp_support: OTG device feature flag, indicating that the A-Host
590 * supports HNP at this port.
591 * @a_alt_hnp_support: OTG device feature flag, indicating that the A-Host
592 * only supports HNP on a different root port.
593 * @b_hnp_enable: OTG device feature flag, indicating that the A-Host
594 * enabled HNP support.
595 * @quirk_ep_out_aligned_size: epout requires buffer size to be aligned to
597 * @is_selfpowered: if the gadget is self-powered.
598 * @deactivated: True if gadget is deactivated - in deactivated state it cannot
600 * @connected: True if gadget is connected.
602 * Gadgets have a mostly-portable "gadget driver" implementing device
603 * functions, handling all usb configurations and interfaces. Gadget
604 * drivers talk to hardware-specific code indirectly, through ops vectors.
605 * That insulates the gadget driver from hardware details, and packages
606 * the hardware endpoints through generic i/o queues. The "usb_gadget"
607 * and "usb_ep" interfaces provide that insulation from the hardware.
609 * Except for the driver data, all fields in this structure are
610 * read-only to the gadget driver. That driver data is part of the
611 * "driver model" infrastructure in 2.6 (and later) kernels, and for
612 * earlier systems is grouped in a similar structure that's not known
613 * to the rest of the kernel.
615 * Values of the three OTG device feature flags are updated before the
616 * setup() call corresponding to USB_REQ_SET_CONFIGURATION, and before
617 * driver suspend() calls. They are valid only when is_otg, and when the
618 * device is acting as a B-Peripheral (so is_a_peripheral is false).
621 struct work_struct work;
623 /* readonly to gadget driver */
624 const struct usb_gadget_ops *ops;
626 struct list_head ep_list; /* of usb_ep */
627 enum usb_device_speed speed;
628 enum usb_device_speed max_speed;
629 enum usb_device_state state;
634 struct usb_otg_caps *otg_caps;
636 unsigned sg_supported:1;
638 unsigned is_a_peripheral:1;
639 unsigned b_hnp_enable:1;
640 unsigned a_hnp_support:1;
641 unsigned a_alt_hnp_support:1;
642 unsigned quirk_ep_out_aligned_size:1;
643 unsigned quirk_altset_not_supp:1;
644 unsigned quirk_stall_not_supp:1;
645 unsigned quirk_zlp_not_supp:1;
646 unsigned is_selfpowered:1;
647 unsigned deactivated:1;
648 unsigned connected:1;
650 #define work_to_gadget(w) (container_of((w), struct usb_gadget, work))
652 static inline void set_gadget_data(struct usb_gadget *gadget, void *data)
653 { dev_set_drvdata(&gadget->dev, data); }
654 static inline void *get_gadget_data(struct usb_gadget *gadget)
655 { return dev_get_drvdata(&gadget->dev); }
656 static inline struct usb_gadget *dev_to_usb_gadget(struct device *dev)
658 return container_of(dev, struct usb_gadget, dev);
661 /* iterates the non-control endpoints; 'tmp' is a struct usb_ep pointer */
662 #define gadget_for_each_ep(tmp, gadget) \
663 list_for_each_entry(tmp, &(gadget)->ep_list, ep_list)
666 * usb_ep_align_maybe - returns @len aligned to ep's maxpacketsize if gadget
667 * requires quirk_ep_out_aligned_size, otherwise reguens len.
668 * @g: controller to check for quirk
669 * @ep: the endpoint whose maxpacketsize is used to align @len
670 * @len: buffer size's length to align to @ep's maxpacketsize
672 * This helper is used in case it's required for any reason to check and maybe
673 * align buffer's size to an ep's maxpacketsize.
676 usb_ep_align_maybe(struct usb_gadget *g, struct usb_ep *ep, size_t len)
678 return !g->quirk_ep_out_aligned_size ? len :
679 round_up(len, (size_t)ep->desc->wMaxPacketSize);
683 * gadget_is_altset_supported - return true iff the hardware supports
685 * @g: controller to check for quirk
687 static inline int gadget_is_altset_supported(struct usb_gadget *g)
689 return !g->quirk_altset_not_supp;
693 * gadget_is_stall_supported - return true iff the hardware supports stalling
694 * @g: controller to check for quirk
696 static inline int gadget_is_stall_supported(struct usb_gadget *g)
698 return !g->quirk_stall_not_supp;
702 * gadget_is_zlp_supported - return true iff the hardware supports zlp
703 * @g: controller to check for quirk
705 static inline int gadget_is_zlp_supported(struct usb_gadget *g)
707 return !g->quirk_zlp_not_supp;
711 * gadget_is_dualspeed - return true iff the hardware handles high speed
712 * @g: controller that might support both high and full speeds
714 static inline int gadget_is_dualspeed(struct usb_gadget *g)
716 return g->max_speed >= USB_SPEED_HIGH;
720 * gadget_is_superspeed() - return true if the hardware handles superspeed
721 * @g: controller that might support superspeed
723 static inline int gadget_is_superspeed(struct usb_gadget *g)
725 return g->max_speed >= USB_SPEED_SUPER;
729 * gadget_is_otg - return true iff the hardware is OTG-ready
730 * @g: controller that might have a Mini-AB connector
732 * This is a runtime test, since kernels with a USB-OTG stack sometimes
733 * run on boards which only have a Mini-B (or Mini-A) connector.
735 static inline int gadget_is_otg(struct usb_gadget *g)
737 #ifdef CONFIG_USB_OTG
745 * usb_gadget_frame_number - returns the current frame number
746 * @gadget: controller that reports the frame number
748 * Returns the usb frame number, normally eleven bits from a SOF packet,
749 * or negative errno if this device doesn't support this capability.
751 static inline int usb_gadget_frame_number(struct usb_gadget *gadget)
753 return gadget->ops->get_frame(gadget);
757 * usb_gadget_wakeup - tries to wake up the host connected to this gadget
758 * @gadget: controller used to wake up the host
760 * Returns zero on success, else negative error code if the hardware
761 * doesn't support such attempts, or its support has not been enabled
762 * by the usb host. Drivers must return device descriptors that report
763 * their ability to support this, or hosts won't enable it.
765 * This may also try to use SRP to wake the host and start enumeration,
766 * even if OTG isn't otherwise in use. OTG devices may also start
767 * remote wakeup even when hosts don't explicitly enable it.
769 static inline int usb_gadget_wakeup(struct usb_gadget *gadget)
771 if (!gadget->ops->wakeup)
773 return gadget->ops->wakeup(gadget);
777 * usb_gadget_set_selfpowered - sets the device selfpowered feature.
778 * @gadget:the device being declared as self-powered
780 * this affects the device status reported by the hardware driver
781 * to reflect that it now has a local power supply.
783 * returns zero on success, else negative errno.
785 static inline int usb_gadget_set_selfpowered(struct usb_gadget *gadget)
787 if (!gadget->ops->set_selfpowered)
789 return gadget->ops->set_selfpowered(gadget, 1);
793 * usb_gadget_clear_selfpowered - clear the device selfpowered feature.
794 * @gadget:the device being declared as bus-powered
796 * this affects the device status reported by the hardware driver.
797 * some hardware may not support bus-powered operation, in which
798 * case this feature's value can never change.
800 * returns zero on success, else negative errno.
802 static inline int usb_gadget_clear_selfpowered(struct usb_gadget *gadget)
804 if (!gadget->ops->set_selfpowered)
806 return gadget->ops->set_selfpowered(gadget, 0);
810 * usb_gadget_vbus_connect - Notify controller that VBUS is powered
811 * @gadget:The device which now has VBUS power.
814 * This call is used by a driver for an external transceiver (or GPIO)
815 * that detects a VBUS power session starting. Common responses include
816 * resuming the controller, activating the D+ (or D-) pullup to let the
817 * host detect that a USB device is attached, and starting to draw power
818 * (8mA or possibly more, especially after SET_CONFIGURATION).
820 * Returns zero on success, else negative errno.
822 static inline int usb_gadget_vbus_connect(struct usb_gadget *gadget)
824 if (!gadget->ops->vbus_session)
826 return gadget->ops->vbus_session(gadget, 1);
830 * usb_gadget_vbus_draw - constrain controller's VBUS power usage
831 * @gadget:The device whose VBUS usage is being described
832 * @mA:How much current to draw, in milliAmperes. This should be twice
833 * the value listed in the configuration descriptor bMaxPower field.
835 * This call is used by gadget drivers during SET_CONFIGURATION calls,
836 * reporting how much power the device may consume. For example, this
837 * could affect how quickly batteries are recharged.
839 * Returns zero on success, else negative errno.
841 static inline int usb_gadget_vbus_draw(struct usb_gadget *gadget, unsigned mA)
843 if (!gadget->ops->vbus_draw)
845 return gadget->ops->vbus_draw(gadget, mA);
849 * usb_gadget_vbus_disconnect - notify controller about VBUS session end
850 * @gadget:the device whose VBUS supply is being described
853 * This call is used by a driver for an external transceiver (or GPIO)
854 * that detects a VBUS power session ending. Common responses include
855 * reversing everything done in usb_gadget_vbus_connect().
857 * Returns zero on success, else negative errno.
859 static inline int usb_gadget_vbus_disconnect(struct usb_gadget *gadget)
861 if (!gadget->ops->vbus_session)
863 return gadget->ops->vbus_session(gadget, 0);
867 * usb_gadget_connect - software-controlled connect to USB host
868 * @gadget:the peripheral being connected
870 * Enables the D+ (or potentially D-) pullup. The host will start
871 * enumerating this gadget when the pullup is active and a VBUS session
872 * is active (the link is powered). This pullup is always enabled unless
873 * usb_gadget_disconnect() has been used to disable it.
875 * Returns zero on success, else negative errno.
877 static inline int usb_gadget_connect(struct usb_gadget *gadget)
881 if (!gadget->ops->pullup)
884 if (gadget->deactivated) {
886 * If gadget is deactivated we only save new state.
887 * Gadget will be connected automatically after activation.
889 gadget->connected = true;
893 ret = gadget->ops->pullup(gadget, 1);
895 gadget->connected = 1;
900 * usb_gadget_disconnect - software-controlled disconnect from USB host
901 * @gadget:the peripheral being disconnected
903 * Disables the D+ (or potentially D-) pullup, which the host may see
904 * as a disconnect (when a VBUS session is active). Not all systems
905 * support software pullup controls.
907 * Returns zero on success, else negative errno.
909 static inline int usb_gadget_disconnect(struct usb_gadget *gadget)
913 if (!gadget->ops->pullup)
916 if (gadget->deactivated) {
918 * If gadget is deactivated we only save new state.
919 * Gadget will stay disconnected after activation.
921 gadget->connected = false;
925 ret = gadget->ops->pullup(gadget, 0);
927 gadget->connected = 0;
932 * usb_gadget_deactivate - deactivate function which is not ready to work
933 * @gadget: the peripheral being deactivated
935 * This routine may be used during the gadget driver bind() call to prevent
936 * the peripheral from ever being visible to the USB host, unless later
937 * usb_gadget_activate() is called. For example, user mode components may
938 * need to be activated before the system can talk to hosts.
940 * Returns zero on success, else negative errno.
942 static inline int usb_gadget_deactivate(struct usb_gadget *gadget)
946 if (gadget->deactivated)
949 if (gadget->connected) {
950 ret = usb_gadget_disconnect(gadget);
954 * If gadget was being connected before deactivation, we want
955 * to reconnect it in usb_gadget_activate().
957 gadget->connected = true;
959 gadget->deactivated = true;
965 * usb_gadget_activate - activate function which is not ready to work
966 * @gadget: the peripheral being activated
968 * This routine activates gadget which was previously deactivated with
969 * usb_gadget_deactivate() call. It calls usb_gadget_connect() if needed.
971 * Returns zero on success, else negative errno.
973 static inline int usb_gadget_activate(struct usb_gadget *gadget)
975 if (!gadget->deactivated)
978 gadget->deactivated = false;
981 * If gadget has been connected before deactivation, or became connected
982 * while it was being deactivated, we call usb_gadget_connect().
984 if (gadget->connected)
985 return usb_gadget_connect(gadget);
990 /*-------------------------------------------------------------------------*/
993 * struct usb_gadget_driver - driver for usb 'slave' devices
994 * @function: String describing the gadget's function
995 * @max_speed: Highest speed the driver handles.
996 * @setup: Invoked for ep0 control requests that aren't handled by
997 * the hardware level driver. Most calls must be handled by
998 * the gadget driver, including descriptor and configuration
999 * management. The 16 bit members of the setup data are in
1000 * USB byte order. Called in_interrupt; this may not sleep. Driver
1001 * queues a response to ep0, or returns negative to stall.
1002 * @disconnect: Invoked after all transfers have been stopped,
1003 * when the host is disconnected. May be called in_interrupt; this
1004 * may not sleep. Some devices can't detect disconnect, so this might
1005 * not be called except as part of controller shutdown.
1006 * @bind: the driver's bind callback
1007 * @unbind: Invoked when the driver is unbound from a gadget,
1008 * usually from rmmod (after a disconnect is reported).
1009 * Called in a context that permits sleeping.
1010 * @suspend: Invoked on USB suspend. May be called in_interrupt.
1011 * @resume: Invoked on USB resume. May be called in_interrupt.
1012 * @reset: Invoked on USB bus reset. It is mandatory for all gadget drivers
1013 * and should be called in_interrupt.
1014 * @driver: Driver model state for this driver.
1016 * Devices are disabled till a gadget driver successfully bind()s, which
1017 * means the driver will handle setup() requests needed to enumerate (and
1018 * meet "chapter 9" requirements) then do some useful work.
1020 * If gadget->is_otg is true, the gadget driver must provide an OTG
1021 * descriptor during enumeration, or else fail the bind() call. In such
1022 * cases, no USB traffic may flow until both bind() returns without
1023 * having called usb_gadget_disconnect(), and the USB host stack has
1026 * Drivers use hardware-specific knowledge to configure the usb hardware.
1027 * endpoint addressing is only one of several hardware characteristics that
1028 * are in descriptors the ep0 implementation returns from setup() calls.
1030 * Except for ep0 implementation, most driver code shouldn't need change to
1031 * run on top of different usb controllers. It'll use endpoints set up by
1032 * that ep0 implementation.
1034 * The usb controller driver handles a few standard usb requests. Those
1035 * include set_address, and feature flags for devices, interfaces, and
1036 * endpoints (the get_status, set_feature, and clear_feature requests).
1038 * Accordingly, the driver's setup() callback must always implement all
1039 * get_descriptor requests, returning at least a device descriptor and
1040 * a configuration descriptor. Drivers must make sure the endpoint
1041 * descriptors match any hardware constraints. Some hardware also constrains
1042 * other descriptors. (The pxa250 allows only configurations 1, 2, or 3).
1044 * The driver's setup() callback must also implement set_configuration,
1045 * and should also implement set_interface, get_configuration, and
1046 * get_interface. Setting a configuration (or interface) is where
1047 * endpoints should be activated or (config 0) shut down.
1049 * (Note that only the default control endpoint is supported. Neither
1050 * hosts nor devices generally support control traffic except to ep0.)
1052 * Most devices will ignore USB suspend/resume operations, and so will
1053 * not provide those callbacks. However, some may need to change modes
1054 * when the host is not longer directing those activities. For example,
1055 * local controls (buttons, dials, etc) may need to be re-enabled since
1056 * the (remote) host can't do that any longer; or an error state might
1057 * be cleared, to make the device behave identically whether or not
1058 * power is maintained.
1060 struct usb_gadget_driver {
1062 enum usb_device_speed max_speed;
1063 int (*bind)(struct usb_gadget *gadget,
1064 struct usb_gadget_driver *driver);
1065 void (*unbind)(struct usb_gadget *);
1066 int (*setup)(struct usb_gadget *,
1067 const struct usb_ctrlrequest *);
1068 void (*disconnect)(struct usb_gadget *);
1069 void (*suspend)(struct usb_gadget *);
1070 void (*resume)(struct usb_gadget *);
1071 void (*reset)(struct usb_gadget *);
1073 /* FIXME support safe rmmod */
1074 struct device_driver driver;
1079 /*-------------------------------------------------------------------------*/
1081 /* driver modules register and unregister, as usual.
1082 * these calls must be made in a context that can sleep.
1084 * these will usually be implemented directly by the hardware-dependent
1085 * usb bus interface driver, which will only support a single driver.
1089 * usb_gadget_probe_driver - probe a gadget driver
1090 * @driver: the driver being registered
1091 * Context: can sleep
1093 * Call this in your gadget driver's module initialization function,
1094 * to tell the underlying usb controller driver about your driver.
1095 * The @bind() function will be called to bind it to a gadget before this
1096 * registration call returns. It's expected that the @bind() function will
1097 * be in init sections.
1099 int usb_gadget_probe_driver(struct usb_gadget_driver *driver);
1102 * usb_gadget_unregister_driver - unregister a gadget driver
1103 * @driver:the driver being unregistered
1104 * Context: can sleep
1106 * Call this in your gadget driver's module cleanup function,
1107 * to tell the underlying usb controller that your driver is
1108 * going away. If the controller is connected to a USB host,
1109 * it will first disconnect(). The driver is also requested
1110 * to unbind() and clean up any device state, before this procedure
1111 * finally returns. It's expected that the unbind() functions
1112 * will in in exit sections, so may not be linked in some kernels.
1114 int usb_gadget_unregister_driver(struct usb_gadget_driver *driver);
1116 extern int usb_add_gadget_udc_release(struct device *parent,
1117 struct usb_gadget *gadget, void (*release)(struct device *dev));
1118 extern int usb_add_gadget_udc(struct device *parent, struct usb_gadget *gadget);
1119 extern void usb_del_gadget_udc(struct usb_gadget *gadget);
1120 extern int usb_udc_attach_driver(const char *name,
1121 struct usb_gadget_driver *driver);
1123 /*-------------------------------------------------------------------------*/
1125 /* utility to simplify dealing with string descriptors */
1128 * struct usb_string - wraps a C string and its USB id
1129 * @id:the (nonzero) ID for this string
1130 * @s:the string, in UTF-8 encoding
1132 * If you're using usb_gadget_get_string(), use this to wrap a string
1133 * together with its ID.
1141 * struct usb_gadget_strings - a set of USB strings in a given language
1142 * @language:identifies the strings' language (0x0409 for en-us)
1143 * @strings:array of strings with their ids
1145 * If you're using usb_gadget_get_string(), use this to wrap all the
1146 * strings for a given language.
1148 struct usb_gadget_strings {
1149 u16 language; /* 0x0409 for en-us */
1150 struct usb_string *strings;
1153 struct usb_gadget_string_container {
1154 struct list_head list;
1158 /* put descriptor for string with that id into buf (buflen >= 256) */
1159 int usb_gadget_get_string(struct usb_gadget_strings *table, int id, u8 *buf);
1161 /*-------------------------------------------------------------------------*/
1163 /* utility to simplify managing config descriptors */
1165 /* write vector of descriptors into buffer */
1166 int usb_descriptor_fillbuf(void *, unsigned,
1167 const struct usb_descriptor_header **);
1169 /* build config descriptor from single descriptor vector */
1170 int usb_gadget_config_buf(const struct usb_config_descriptor *config,
1171 void *buf, unsigned buflen, const struct usb_descriptor_header **desc);
1173 /* copy a NULL-terminated vector of descriptors */
1174 struct usb_descriptor_header **usb_copy_descriptors(
1175 struct usb_descriptor_header **);
1178 * usb_free_descriptors - free descriptors returned by usb_copy_descriptors()
1179 * @v: vector of descriptors
1181 static inline void usb_free_descriptors(struct usb_descriptor_header **v)
1186 struct usb_function;
1187 int usb_assign_descriptors(struct usb_function *f,
1188 struct usb_descriptor_header **fs,
1189 struct usb_descriptor_header **hs,
1190 struct usb_descriptor_header **ss);
1191 void usb_free_all_descriptors(struct usb_function *f);
1193 struct usb_descriptor_header *usb_otg_descriptor_alloc(
1194 struct usb_gadget *gadget);
1195 int usb_otg_descriptor_init(struct usb_gadget *gadget,
1196 struct usb_descriptor_header *otg_desc);
1197 /*-------------------------------------------------------------------------*/
1199 /* utility to simplify map/unmap of usb_requests to/from DMA */
1201 extern int usb_gadget_map_request(struct usb_gadget *gadget,
1202 struct usb_request *req, int is_in);
1204 extern void usb_gadget_unmap_request(struct usb_gadget *gadget,
1205 struct usb_request *req, int is_in);
1207 /*-------------------------------------------------------------------------*/
1209 /* utility to set gadget state properly */
1211 extern void usb_gadget_set_state(struct usb_gadget *gadget,
1212 enum usb_device_state state);
1214 /*-------------------------------------------------------------------------*/
1216 /* utility to tell udc core that the bus reset occurs */
1217 extern void usb_gadget_udc_reset(struct usb_gadget *gadget,
1218 struct usb_gadget_driver *driver);
1220 /*-------------------------------------------------------------------------*/
1222 /* utility to give requests back to the gadget layer */
1224 extern void usb_gadget_giveback_request(struct usb_ep *ep,
1225 struct usb_request *req);
1227 /*-------------------------------------------------------------------------*/
1229 /* utility to find endpoint by name */
1231 extern struct usb_ep *gadget_find_ep_by_name(struct usb_gadget *g,
1234 /*-------------------------------------------------------------------------*/
1236 /* utility to check if endpoint caps match descriptor needs */
1238 extern int usb_gadget_ep_match_desc(struct usb_gadget *gadget,
1239 struct usb_ep *ep, struct usb_endpoint_descriptor *desc,
1240 struct usb_ss_ep_comp_descriptor *ep_comp);
1242 /*-------------------------------------------------------------------------*/
1244 /* utility to update vbus status for udc core, it may be scheduled */
1245 extern void usb_udc_vbus_handler(struct usb_gadget *gadget, bool status);
1247 /*-------------------------------------------------------------------------*/
1249 /* utility wrapping a simple endpoint selection policy */
1251 extern struct usb_ep *usb_ep_autoconfig(struct usb_gadget *,
1252 struct usb_endpoint_descriptor *);
1255 extern struct usb_ep *usb_ep_autoconfig_ss(struct usb_gadget *,
1256 struct usb_endpoint_descriptor *,
1257 struct usb_ss_ep_comp_descriptor *);
1259 extern void usb_ep_autoconfig_release(struct usb_ep *);
1261 extern void usb_ep_autoconfig_reset(struct usb_gadget *);
1263 #endif /* __LINUX_USB_GADGET_H */