2 * mac80211 <-> driver interface
4 * Copyright 2002-2005, Devicescape Software, Inc.
5 * Copyright 2006-2007 Jiri Benc <jbenc@suse.cz>
6 * Copyright 2007-2010 Johannes Berg <johannes@sipsolutions.net>
8 * This program is free software; you can redistribute it and/or modify
9 * it under the terms of the GNU General Public License version 2 as
10 * published by the Free Software Foundation.
16 #include <linux/kernel.h>
17 #include <linux/if_ether.h>
18 #include <linux/skbuff.h>
19 #include <linux/device.h>
20 #include <linux/ieee80211.h>
21 #include <net/cfg80211.h>
22 #include <asm/unaligned.h>
27 * mac80211 is the Linux stack for 802.11 hardware that implements
28 * only partial functionality in hard- or firmware. This document
29 * defines the interface between mac80211 and low-level hardware
34 * DOC: Calling mac80211 from interrupts
36 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
37 * called in hardware interrupt context. The low-level driver must not call any
38 * other functions in hardware interrupt context. If there is a need for such
39 * call, the low-level driver should first ACK the interrupt and perform the
40 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
43 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also
44 * use the non-IRQ-safe functions!
50 * If you're reading this document and not the header file itself, it will
51 * be incomplete because not all documentation has been converted yet.
57 * As a general rule, when frames are passed between mac80211 and the driver,
58 * they start with the IEEE 802.11 header and include the same octets that are
59 * sent over the air except for the FCS which should be calculated by the
62 * There are, however, various exceptions to this rule for advanced features:
64 * The first exception is for hardware encryption and decryption offload
65 * where the IV/ICV may or may not be generated in hardware.
67 * Secondly, when the hardware handles fragmentation, the frame handed to
68 * the driver from mac80211 is the MSDU, not the MPDU.
70 * Finally, for received frames, the driver is able to indicate that it has
71 * filled a radiotap header and put that in front of the frame; if it does
72 * not do so then mac80211 may add this under certain circumstances.
76 * DOC: mac80211 workqueue
78 * mac80211 provides its own workqueue for drivers and internal mac80211 use.
79 * The workqueue is a single threaded workqueue and can only be accessed by
80 * helpers for sanity checking. Drivers must ensure all work added onto the
81 * mac80211 workqueue should be cancelled on the driver stop() callback.
83 * mac80211 will flushed the workqueue upon interface removal and during
86 * All work performed on the mac80211 workqueue must not acquire the RTNL lock.
91 * enum ieee80211_max_queues - maximum number of queues
93 * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
95 enum ieee80211_max_queues {
96 IEEE80211_MAX_QUEUES = 4,
100 * enum ieee80211_ac_numbers - AC numbers as used in mac80211
101 * @IEEE80211_AC_VO: voice
102 * @IEEE80211_AC_VI: video
103 * @IEEE80211_AC_BE: best effort
104 * @IEEE80211_AC_BK: background
106 enum ieee80211_ac_numbers {
114 * struct ieee80211_tx_queue_params - transmit queue configuration
116 * The information provided in this structure is required for QoS
117 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
119 * @aifs: arbitration interframe space [0..255]
120 * @cw_min: minimum contention window [a value of the form
121 * 2^n-1 in the range 1..32767]
122 * @cw_max: maximum contention window [like @cw_min]
123 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
124 * @uapsd: is U-APSD mode enabled for the queue
126 struct ieee80211_tx_queue_params {
134 struct ieee80211_low_level_stats {
135 unsigned int dot11ACKFailureCount;
136 unsigned int dot11RTSFailureCount;
137 unsigned int dot11FCSErrorCount;
138 unsigned int dot11RTSSuccessCount;
142 * enum ieee80211_bss_change - BSS change notification flags
144 * These flags are used with the bss_info_changed() callback
145 * to indicate which BSS parameter changed.
147 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
148 * also implies a change in the AID.
149 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
150 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
151 * @BSS_CHANGED_ERP_SLOT: slot timing changed
152 * @BSS_CHANGED_HT: 802.11n parameters changed
153 * @BSS_CHANGED_BASIC_RATES: Basic rateset changed
154 * @BSS_CHANGED_BEACON_INT: Beacon interval changed
155 * @BSS_CHANGED_BSSID: BSSID changed, for whatever
156 * reason (IBSS and managed mode)
157 * @BSS_CHANGED_BEACON: Beacon data changed, retrieve
158 * new beacon (beaconing modes)
159 * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
160 * enabled/disabled (beaconing modes)
161 * @BSS_CHANGED_CQM: Connection quality monitor config changed
162 * @BSS_CHANGED_IBSS: IBSS join status changed
163 * @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed.
164 * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note
165 * that it is only ever disabled for station mode.
166 * @BSS_CHANGED_IDLE: Idle changed for this BSS/interface.
168 enum ieee80211_bss_change {
169 BSS_CHANGED_ASSOC = 1<<0,
170 BSS_CHANGED_ERP_CTS_PROT = 1<<1,
171 BSS_CHANGED_ERP_PREAMBLE = 1<<2,
172 BSS_CHANGED_ERP_SLOT = 1<<3,
173 BSS_CHANGED_HT = 1<<4,
174 BSS_CHANGED_BASIC_RATES = 1<<5,
175 BSS_CHANGED_BEACON_INT = 1<<6,
176 BSS_CHANGED_BSSID = 1<<7,
177 BSS_CHANGED_BEACON = 1<<8,
178 BSS_CHANGED_BEACON_ENABLED = 1<<9,
179 BSS_CHANGED_CQM = 1<<10,
180 BSS_CHANGED_IBSS = 1<<11,
181 BSS_CHANGED_ARP_FILTER = 1<<12,
182 BSS_CHANGED_QOS = 1<<13,
183 BSS_CHANGED_IDLE = 1<<14,
185 /* when adding here, make sure to change ieee80211_reconfig */
189 * The maximum number of IPv4 addresses listed for ARP filtering. If the number
190 * of addresses for an interface increase beyond this value, hardware ARP
191 * filtering will be disabled.
193 #define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4
196 * enum ieee80211_rssi_event - RSSI threshold event
197 * An indicator for when RSSI goes below/above a certain threshold.
198 * @RSSI_EVENT_HIGH: AP's rssi crossed the high threshold set by the driver.
199 * @RSSI_EVENT_LOW: AP's rssi crossed the low threshold set by the driver.
201 enum ieee80211_rssi_event {
207 * struct ieee80211_bss_conf - holds the BSS's changing parameters
209 * This structure keeps information about a BSS (and an association
210 * to that BSS) that can change during the lifetime of the BSS.
212 * @assoc: association status
213 * @ibss_joined: indicates whether this station is part of an IBSS
215 * @aid: association ID number, valid only when @assoc is true
216 * @use_cts_prot: use CTS protection
217 * @use_short_preamble: use 802.11b short preamble;
218 * if the hardware cannot handle this it must set the
219 * IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE hardware flag
220 * @use_short_slot: use short slot time (only relevant for ERP);
221 * if the hardware cannot handle this it must set the
222 * IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag
223 * @dtim_period: num of beacons before the next DTIM, for beaconing,
224 * valid in station mode only while @assoc is true and if also
225 * requested by %IEEE80211_HW_NEED_DTIM_PERIOD (cf. also hw conf
227 * @timestamp: beacon timestamp
228 * @beacon_int: beacon interval
229 * @assoc_capability: capabilities taken from assoc resp
230 * @basic_rates: bitmap of basic rates, each bit stands for an
231 * index into the rate table configured by the driver in
233 * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
234 * @bssid: The BSSID for this BSS
235 * @enable_beacon: whether beaconing should be enabled or not
236 * @channel_type: Channel type for this BSS -- the hardware might be
237 * configured for HT40+ while this BSS only uses no-HT, for
239 * @ht_operation_mode: HT operation mode (like in &struct ieee80211_ht_info).
240 * This field is only valid when the channel type is one of the HT types.
241 * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value
243 * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis
244 * @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The
245 * may filter ARP queries targeted for other addresses than listed here.
246 * The driver must allow ARP queries targeted for all address listed here
247 * to pass through. An empty list implies no ARP queries need to pass.
248 * @arp_addr_cnt: Number of addresses currently on the list.
249 * @arp_filter_enabled: Enable ARP filtering - if enabled, the hardware may
250 * filter ARP queries based on the @arp_addr_list, if disabled, the
251 * hardware must not perform any ARP filtering. Note, that the filter will
252 * be enabled also in promiscuous mode.
253 * @qos: This is a QoS-enabled BSS.
254 * @idle: This interface is idle. There's also a global idle flag in the
255 * hardware config which may be more appropriate depending on what
256 * your driver/device needs to do.
258 struct ieee80211_bss_conf {
260 /* association related data */
261 bool assoc, ibss_joined;
263 /* erp related data */
265 bool use_short_preamble;
270 u16 assoc_capability;
273 int mcast_rate[IEEE80211_NUM_BANDS];
274 u16 ht_operation_mode;
277 enum nl80211_channel_type channel_type;
278 __be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN];
280 bool arp_filter_enabled;
286 * enum mac80211_tx_control_flags - flags to describe transmission information/status
288 * These flags are used with the @flags member of &ieee80211_tx_info.
290 * @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame.
291 * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
292 * number to this frame, taking care of not overwriting the fragment
293 * number and increasing the sequence number only when the
294 * IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly
295 * assign sequence numbers to QoS-data frames but cannot do so correctly
296 * for non-QoS-data and management frames because beacons need them from
297 * that counter as well and mac80211 cannot guarantee proper sequencing.
298 * If this flag is set, the driver should instruct the hardware to
299 * assign a sequence number to the frame or assign one itself. Cf. IEEE
300 * 802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
301 * beacons and always be clear for frames without a sequence number field.
302 * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
303 * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
305 * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
306 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
307 * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
308 * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211.
309 * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
310 * because the destination STA was in powersave mode. Note that to
311 * avoid race conditions, the filter must be set by the hardware or
312 * firmware upon receiving a frame that indicates that the station
313 * went to sleep (must be done on device to filter frames already on
314 * the queue) and may only be unset after mac80211 gives the OK for
315 * that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above),
316 * since only then is it guaranteed that no more frames are in the
318 * @IEEE80211_TX_STAT_ACK: Frame was acknowledged
319 * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
320 * is for the whole aggregation.
321 * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
322 * so consider using block ack request (BAR).
323 * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
324 * set by rate control algorithms to indicate probe rate, will
325 * be cleared for fragmented frames (except on the last fragment)
326 * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211,
327 * used to indicate that a pending frame requires TX processing before
328 * it can be sent out.
329 * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211,
330 * used to indicate that a frame was already retried due to PS
331 * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211,
332 * used to indicate frame should not be encrypted
333 * @IEEE80211_TX_CTL_PSPOLL_RESPONSE: (internal?)
334 * This frame is a response to a PS-poll frame and should be sent
335 * although the station is in powersave mode.
336 * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the
337 * transmit function after the current frame, this can be used
338 * by drivers to kick the DMA queue only if unset or when the
340 * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted
341 * after TX status because the destination was asleep, it must not
342 * be modified again (no seqno assignment, crypto, etc.)
343 * @IEEE80211_TX_INTFL_HAS_RADIOTAP: This frame was injected and still
344 * has a radiotap header at skb->data.
345 * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211
346 * MLME command (internal to mac80211 to figure out whether to send TX
347 * status to user space)
348 * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame
349 * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this
350 * frame and selects the maximum number of streams that it can use.
351 * @IEEE80211_TX_CTL_TX_OFFCHAN: Marks this packet to be transmitted on
352 * the off-channel channel when a remain-on-channel offload is done
353 * in hardware -- normal packets still flow and are expected to be
354 * handled properly by the device.
355 * @IEEE80211_TX_INTFL_TKIP_MIC_FAILURE: Marks this packet to be used for TKIP
356 * testing. It will be sent out with incorrect Michael MIC key to allow
357 * TKIP countermeasures to be tested.
359 * Note: If you have to add new flags to the enumeration, then don't
360 * forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary.
362 enum mac80211_tx_control_flags {
363 IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
364 IEEE80211_TX_CTL_ASSIGN_SEQ = BIT(1),
365 IEEE80211_TX_CTL_NO_ACK = BIT(2),
366 IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(3),
367 IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(4),
368 IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(5),
369 IEEE80211_TX_CTL_AMPDU = BIT(6),
370 IEEE80211_TX_CTL_INJECTED = BIT(7),
371 IEEE80211_TX_STAT_TX_FILTERED = BIT(8),
372 IEEE80211_TX_STAT_ACK = BIT(9),
373 IEEE80211_TX_STAT_AMPDU = BIT(10),
374 IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11),
375 IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12),
376 IEEE80211_TX_INTFL_NEED_TXPROCESSING = BIT(14),
377 IEEE80211_TX_INTFL_RETRIED = BIT(15),
378 IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16),
379 IEEE80211_TX_CTL_PSPOLL_RESPONSE = BIT(17),
380 IEEE80211_TX_CTL_MORE_FRAMES = BIT(18),
381 IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19),
382 IEEE80211_TX_INTFL_HAS_RADIOTAP = BIT(20),
383 IEEE80211_TX_INTFL_NL80211_FRAME_TX = BIT(21),
384 IEEE80211_TX_CTL_LDPC = BIT(22),
385 IEEE80211_TX_CTL_STBC = BIT(23) | BIT(24),
386 IEEE80211_TX_CTL_TX_OFFCHAN = BIT(25),
387 IEEE80211_TX_INTFL_TKIP_MIC_FAILURE = BIT(26),
390 #define IEEE80211_TX_CTL_STBC_SHIFT 23
393 * This definition is used as a mask to clear all temporary flags, which are
394 * set by the tx handlers for each transmission attempt by the mac80211 stack.
396 #define IEEE80211_TX_TEMPORARY_FLAGS (IEEE80211_TX_CTL_NO_ACK | \
397 IEEE80211_TX_CTL_CLEAR_PS_FILT | IEEE80211_TX_CTL_FIRST_FRAGMENT | \
398 IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU | \
399 IEEE80211_TX_STAT_TX_FILTERED | IEEE80211_TX_STAT_ACK | \
400 IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK | \
401 IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_PSPOLL_RESPONSE | \
402 IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC | \
403 IEEE80211_TX_CTL_STBC)
406 * enum mac80211_rate_control_flags - per-rate flags set by the
407 * Rate Control algorithm.
409 * These flags are set by the Rate control algorithm for each rate during tx,
410 * in the @flags member of struct ieee80211_tx_rate.
412 * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate.
413 * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
414 * This is set if the current BSS requires ERP protection.
415 * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble.
416 * @IEEE80211_TX_RC_MCS: HT rate.
417 * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in
419 * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz.
420 * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the
421 * adjacent 20 MHz channels, if the current channel type is
422 * NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS.
423 * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate.
425 enum mac80211_rate_control_flags {
426 IEEE80211_TX_RC_USE_RTS_CTS = BIT(0),
427 IEEE80211_TX_RC_USE_CTS_PROTECT = BIT(1),
428 IEEE80211_TX_RC_USE_SHORT_PREAMBLE = BIT(2),
430 /* rate index is an MCS rate number instead of an index */
431 IEEE80211_TX_RC_MCS = BIT(3),
432 IEEE80211_TX_RC_GREEN_FIELD = BIT(4),
433 IEEE80211_TX_RC_40_MHZ_WIDTH = BIT(5),
434 IEEE80211_TX_RC_DUP_DATA = BIT(6),
435 IEEE80211_TX_RC_SHORT_GI = BIT(7),
439 /* there are 40 bytes if you don't need the rateset to be kept */
440 #define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40
442 /* if you do need the rateset, then you have less space */
443 #define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24
445 /* maximum number of rate stages */
446 #define IEEE80211_TX_MAX_RATES 5
449 * struct ieee80211_tx_rate - rate selection/status
451 * @idx: rate index to attempt to send with
452 * @flags: rate control flags (&enum mac80211_rate_control_flags)
453 * @count: number of tries in this rate before going to the next rate
455 * A value of -1 for @idx indicates an invalid rate and, if used
456 * in an array of retry rates, that no more rates should be tried.
458 * When used for transmit status reporting, the driver should
459 * always report the rate along with the flags it used.
461 * &struct ieee80211_tx_info contains an array of these structs
462 * in the control information, and it will be filled by the rate
463 * control algorithm according to what should be sent. For example,
464 * if this array contains, in the format { <idx>, <count> } the
466 * { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 }
467 * then this means that the frame should be transmitted
468 * up to twice at rate 3, up to twice at rate 2, and up to four
469 * times at rate 1 if it doesn't get acknowledged. Say it gets
470 * acknowledged by the peer after the fifth attempt, the status
471 * information should then contain
472 * { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ...
473 * since it was transmitted twice at rate 3, twice at rate 2
474 * and once at rate 1 after which we received an acknowledgement.
476 struct ieee80211_tx_rate {
483 * struct ieee80211_tx_info - skb transmit information
485 * This structure is placed in skb->cb for three uses:
486 * (1) mac80211 TX control - mac80211 tells the driver what to do
487 * (2) driver internal use (if applicable)
488 * (3) TX status information - driver tells mac80211 what happened
490 * The TX control's sta pointer is only valid during the ->tx call,
493 * @flags: transmit info flags, defined above
494 * @band: the band to transmit on (use for checking for races)
495 * @antenna_sel_tx: antenna to use, 0 for automatic diversity
496 * @pad: padding, ignore
497 * @control: union for control data
498 * @status: union for status data
499 * @driver_data: array of driver_data pointers
500 * @ampdu_ack_len: number of acked aggregated frames.
501 * relevant only if IEEE80211_TX_STAT_AMPDU was set.
502 * @ampdu_len: number of aggregated frames.
503 * relevant only if IEEE80211_TX_STAT_AMPDU was set.
504 * @ack_signal: signal strength of the ACK frame
506 struct ieee80211_tx_info {
507 /* common information */
521 struct ieee80211_tx_rate rates[
522 IEEE80211_TX_MAX_RATES];
525 /* only needed before rate control */
526 unsigned long jiffies;
528 /* NB: vif can be NULL for injected frames */
529 struct ieee80211_vif *vif;
530 struct ieee80211_key_conf *hw_key;
531 struct ieee80211_sta *sta;
534 struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
541 struct ieee80211_tx_rate driver_rates[
542 IEEE80211_TX_MAX_RATES];
543 void *rate_driver_data[
544 IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)];
547 IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)];
552 * struct ieee80211_sched_scan_ies - scheduled scan IEs
554 * This structure is used to pass the appropriate IEs to be used in scheduled
555 * scans for all bands. It contains both the IEs passed from the userspace
556 * and the ones generated by mac80211.
558 * @ie: array with the IEs for each supported band
559 * @len: array with the total length of the IEs for each band
561 struct ieee80211_sched_scan_ies {
562 u8 *ie[IEEE80211_NUM_BANDS];
563 size_t len[IEEE80211_NUM_BANDS];
566 static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
568 return (struct ieee80211_tx_info *)skb->cb;
571 static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb)
573 return (struct ieee80211_rx_status *)skb->cb;
577 * ieee80211_tx_info_clear_status - clear TX status
579 * @info: The &struct ieee80211_tx_info to be cleared.
581 * When the driver passes an skb back to mac80211, it must report
582 * a number of things in TX status. This function clears everything
583 * in the TX status but the rate control information (it does clear
584 * the count since you need to fill that in anyway).
586 * NOTE: You can only use this function if you do NOT use
587 * info->driver_data! Use info->rate_driver_data
588 * instead if you need only the less space that allows.
591 ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
595 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
596 offsetof(struct ieee80211_tx_info, control.rates));
597 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
598 offsetof(struct ieee80211_tx_info, driver_rates));
599 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8);
600 /* clear the rate counts */
601 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
602 info->status.rates[i].count = 0;
605 offsetof(struct ieee80211_tx_info, status.ampdu_ack_len) != 23);
606 memset(&info->status.ampdu_ack_len, 0,
607 sizeof(struct ieee80211_tx_info) -
608 offsetof(struct ieee80211_tx_info, status.ampdu_ack_len));
613 * enum mac80211_rx_flags - receive flags
615 * These flags are used with the @flag member of &struct ieee80211_rx_status.
616 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
617 * Use together with %RX_FLAG_MMIC_STRIPPED.
618 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
619 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
620 * verification has been done by the hardware.
621 * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame.
622 * If this flag is set, the stack cannot do any replay detection
623 * hence the driver or hardware will have to do that.
624 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
626 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
628 * @RX_FLAG_MACTIME_MPDU: The timestamp passed in the RX status (@mactime
629 * field) is valid and contains the time the first symbol of the MPDU
630 * was received. This is useful in monitor mode and for proper IBSS
632 * @RX_FLAG_SHORTPRE: Short preamble was used for this frame
633 * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index
634 * @RX_FLAG_40MHZ: HT40 (40 MHz) was used
635 * @RX_FLAG_SHORT_GI: Short guard interval was used
637 enum mac80211_rx_flags {
638 RX_FLAG_MMIC_ERROR = 1<<0,
639 RX_FLAG_DECRYPTED = 1<<1,
640 RX_FLAG_MMIC_STRIPPED = 1<<3,
641 RX_FLAG_IV_STRIPPED = 1<<4,
642 RX_FLAG_FAILED_FCS_CRC = 1<<5,
643 RX_FLAG_FAILED_PLCP_CRC = 1<<6,
644 RX_FLAG_MACTIME_MPDU = 1<<7,
645 RX_FLAG_SHORTPRE = 1<<8,
647 RX_FLAG_40MHZ = 1<<10,
648 RX_FLAG_SHORT_GI = 1<<11,
652 * struct ieee80211_rx_status - receive status
654 * The low-level driver should provide this information (the subset
655 * supported by hardware) to the 802.11 code with each received
656 * frame, in the skb's control buffer (cb).
658 * @mactime: value in microseconds of the 64-bit Time Synchronization Function
659 * (TSF) timer when the first data symbol (MPDU) arrived at the hardware.
660 * @band: the active band when this frame was received
661 * @freq: frequency the radio was tuned to when receiving this frame, in MHz
662 * @signal: signal strength when receiving this frame, either in dBm, in dB or
663 * unspecified depending on the hardware capabilities flags
664 * @IEEE80211_HW_SIGNAL_*
665 * @antenna: antenna used
666 * @rate_idx: index of data rate into band's supported rates or MCS index if
667 * HT rates are use (RX_FLAG_HT)
669 * @rx_flags: internal RX flags for mac80211
671 struct ieee80211_rx_status {
673 enum ieee80211_band band;
679 unsigned int rx_flags;
683 * enum ieee80211_conf_flags - configuration flags
685 * Flags to define PHY configuration options
687 * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this
688 * to determine for example whether to calculate timestamps for packets
689 * or not, do not use instead of filter flags!
690 * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only).
691 * This is the power save mode defined by IEEE 802.11-2007 section 11.2,
692 * meaning that the hardware still wakes up for beacons, is able to
693 * transmit frames and receive the possible acknowledgment frames.
694 * Not to be confused with hardware specific wakeup/sleep states,
695 * driver is responsible for that. See the section "Powersave support"
697 * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
698 * the driver should be prepared to handle configuration requests but
699 * may turn the device off as much as possible. Typically, this flag will
700 * be set when an interface is set UP but not associated or scanning, but
701 * it can also be unset in that case when monitor interfaces are active.
702 * @IEEE80211_CONF_OFFCHANNEL: The device is currently not on its main
705 enum ieee80211_conf_flags {
706 IEEE80211_CONF_MONITOR = (1<<0),
707 IEEE80211_CONF_PS = (1<<1),
708 IEEE80211_CONF_IDLE = (1<<2),
709 IEEE80211_CONF_OFFCHANNEL = (1<<3),
714 * enum ieee80211_conf_changed - denotes which configuration changed
716 * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
717 * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed
718 * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed
719 * @IEEE80211_CONF_CHANGE_POWER: the TX power changed
720 * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
721 * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
722 * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
723 * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
725 enum ieee80211_conf_changed {
726 IEEE80211_CONF_CHANGE_SMPS = BIT(1),
727 IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2),
728 IEEE80211_CONF_CHANGE_MONITOR = BIT(3),
729 IEEE80211_CONF_CHANGE_PS = BIT(4),
730 IEEE80211_CONF_CHANGE_POWER = BIT(5),
731 IEEE80211_CONF_CHANGE_CHANNEL = BIT(6),
732 IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(7),
733 IEEE80211_CONF_CHANGE_IDLE = BIT(8),
737 * enum ieee80211_smps_mode - spatial multiplexing power save mode
739 * @IEEE80211_SMPS_AUTOMATIC: automatic
740 * @IEEE80211_SMPS_OFF: off
741 * @IEEE80211_SMPS_STATIC: static
742 * @IEEE80211_SMPS_DYNAMIC: dynamic
743 * @IEEE80211_SMPS_NUM_MODES: internal, don't use
745 enum ieee80211_smps_mode {
746 IEEE80211_SMPS_AUTOMATIC,
748 IEEE80211_SMPS_STATIC,
749 IEEE80211_SMPS_DYNAMIC,
752 IEEE80211_SMPS_NUM_MODES,
756 * struct ieee80211_conf - configuration of the device
758 * This struct indicates how the driver shall configure the hardware.
760 * @flags: configuration flags defined above
762 * @listen_interval: listen interval in units of beacon interval
763 * @max_sleep_period: the maximum number of beacon intervals to sleep for
764 * before checking the beacon for a TIM bit (managed mode only); this
765 * value will be only achievable between DTIM frames, the hardware
766 * needs to check for the multicast traffic bit in DTIM beacons.
767 * This variable is valid only when the CONF_PS flag is set.
768 * @ps_dtim_period: The DTIM period of the AP we're connected to, for use
769 * in power saving. Power saving will not be enabled until a beacon
770 * has been received and the DTIM period is known.
771 * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
772 * powersave documentation below. This variable is valid only when
773 * the CONF_PS flag is set.
775 * @power_level: requested transmit power (in dBm)
777 * @channel: the channel to tune to
778 * @channel_type: the channel (HT) type
780 * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
781 * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
782 * but actually means the number of transmissions not the number of retries
783 * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
784 * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
785 * number of transmissions not the number of retries
787 * @smps_mode: spatial multiplexing powersave mode; note that
788 * %IEEE80211_SMPS_STATIC is used when the device is not
789 * configured for an HT channel
791 struct ieee80211_conf {
793 int power_level, dynamic_ps_timeout;
794 int max_sleep_period;
799 u8 long_frame_max_tx_count, short_frame_max_tx_count;
801 struct ieee80211_channel *channel;
802 enum nl80211_channel_type channel_type;
803 enum ieee80211_smps_mode smps_mode;
807 * struct ieee80211_channel_switch - holds the channel switch data
809 * The information provided in this structure is required for channel switch
812 * @timestamp: value in microseconds of the 64-bit Time Synchronization
813 * Function (TSF) timer when the frame containing the channel switch
814 * announcement was received. This is simply the rx.mactime parameter
815 * the driver passed into mac80211.
816 * @block_tx: Indicates whether transmission must be blocked before the
817 * scheduled channel switch, as indicated by the AP.
818 * @channel: the new channel to switch to
819 * @count: the number of TBTT's until the channel switch event
821 struct ieee80211_channel_switch {
824 struct ieee80211_channel *channel;
829 * struct ieee80211_vif - per-interface data
831 * Data in this structure is continually present for driver
832 * use during the life of a virtual interface.
834 * @type: type of this virtual interface
835 * @bss_conf: BSS configuration for this interface, either our own
836 * or the BSS we're associated to
837 * @addr: address of this interface
838 * @p2p: indicates whether this AP or STA interface is a p2p
839 * interface, i.e. a GO or p2p-sta respectively
840 * @drv_priv: data area for driver use, will always be aligned to
843 struct ieee80211_vif {
844 enum nl80211_iftype type;
845 struct ieee80211_bss_conf bss_conf;
849 u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
852 static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
854 #ifdef CONFIG_MAC80211_MESH
855 return vif->type == NL80211_IFTYPE_MESH_POINT;
861 * enum ieee80211_key_flags - key flags
863 * These flags are used for communication about keys between the driver
864 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
866 * @IEEE80211_KEY_FLAG_WMM_STA: Set by mac80211, this flag indicates
867 * that the STA this key will be used with could be using QoS.
868 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
869 * driver to indicate that it requires IV generation for this
871 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
872 * the driver for a TKIP key if it requires Michael MIC
873 * generation in software.
874 * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
875 * that the key is pairwise rather then a shared key.
876 * @IEEE80211_KEY_FLAG_SW_MGMT: This flag should be set by the driver for a
877 * CCMP key if it requires CCMP encryption of management frames (MFP) to
878 * be done in software.
880 enum ieee80211_key_flags {
881 IEEE80211_KEY_FLAG_WMM_STA = 1<<0,
882 IEEE80211_KEY_FLAG_GENERATE_IV = 1<<1,
883 IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
884 IEEE80211_KEY_FLAG_PAIRWISE = 1<<3,
885 IEEE80211_KEY_FLAG_SW_MGMT = 1<<4,
889 * struct ieee80211_key_conf - key information
891 * This key information is given by mac80211 to the driver by
892 * the set_key() callback in &struct ieee80211_ops.
894 * @hw_key_idx: To be set by the driver, this is the key index the driver
895 * wants to be given when a frame is transmitted and needs to be
896 * encrypted in hardware.
897 * @cipher: The key's cipher suite selector.
898 * @flags: key flags, see &enum ieee80211_key_flags.
899 * @keyidx: the key index (0-3)
900 * @keylen: key material length
901 * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
903 * - Temporal Encryption Key (128 bits)
904 * - Temporal Authenticator Tx MIC Key (64 bits)
905 * - Temporal Authenticator Rx MIC Key (64 bits)
906 * @icv_len: The ICV length for this key type
907 * @iv_len: The IV length for this key type
909 struct ieee80211_key_conf {
921 * enum set_key_cmd - key command
923 * Used with the set_key() callback in &struct ieee80211_ops, this
924 * indicates whether a key is being removed or added.
926 * @SET_KEY: a key is set
927 * @DISABLE_KEY: a key must be disabled
930 SET_KEY, DISABLE_KEY,
934 * struct ieee80211_sta - station table entry
936 * A station table entry represents a station we are possibly
937 * communicating with. Since stations are RCU-managed in
938 * mac80211, any ieee80211_sta pointer you get access to must
939 * either be protected by rcu_read_lock() explicitly or implicitly,
940 * or you must take good care to not use such a pointer after a
941 * call to your sta_remove callback that removed it.
944 * @aid: AID we assigned to the station if we're an AP
945 * @supp_rates: Bitmap of supported rates (per band)
946 * @ht_cap: HT capabilities of this STA; restricted to our own TX capabilities
947 * @wme: indicates whether the STA supports WME. Only valid during AP-mode.
948 * @drv_priv: data area for driver use, will always be aligned to
949 * sizeof(void *), size is determined in hw information.
951 struct ieee80211_sta {
952 u32 supp_rates[IEEE80211_NUM_BANDS];
955 struct ieee80211_sta_ht_cap ht_cap;
959 u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
963 * enum sta_notify_cmd - sta notify command
965 * Used with the sta_notify() callback in &struct ieee80211_ops, this
966 * indicates if an associated station made a power state transition.
968 * @STA_NOTIFY_SLEEP: a station is now sleeping
969 * @STA_NOTIFY_AWAKE: a sleeping station woke up
971 enum sta_notify_cmd {
972 STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE,
976 * enum ieee80211_hw_flags - hardware flags
978 * These flags are used to indicate hardware capabilities to
979 * the stack. Generally, flags here should have their meaning
980 * done in a way that the simplest hardware doesn't need setting
981 * any particular flags. There are some exceptions to this rule,
982 * however, so you are advised to review these flags carefully.
984 * @IEEE80211_HW_HAS_RATE_CONTROL:
985 * The hardware or firmware includes rate control, and cannot be
986 * controlled by the stack. As such, no rate control algorithm
987 * should be instantiated, and the TX rate reported to userspace
988 * will be taken from the TX status instead of the rate control
990 * Note that this requires that the driver implement a number of
991 * callbacks so it has the correct information, it needs to have
992 * the @set_rts_threshold callback and must look at the BSS config
993 * @use_cts_prot for G/N protection, @use_short_slot for slot
994 * timing in 2.4 GHz and @use_short_preamble for preambles for
997 * @IEEE80211_HW_RX_INCLUDES_FCS:
998 * Indicates that received frames passed to the stack include
999 * the FCS at the end.
1001 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
1002 * Some wireless LAN chipsets buffer broadcast/multicast frames
1003 * for power saving stations in the hardware/firmware and others
1004 * rely on the host system for such buffering. This option is used
1005 * to configure the IEEE 802.11 upper layer to buffer broadcast and
1006 * multicast frames when there are power saving stations so that
1007 * the driver can fetch them with ieee80211_get_buffered_bc().
1009 * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
1010 * Hardware is not capable of short slot operation on the 2.4 GHz band.
1012 * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
1013 * Hardware is not capable of receiving frames with short preamble on
1016 * @IEEE80211_HW_SIGNAL_UNSPEC:
1017 * Hardware can provide signal values but we don't know its units. We
1018 * expect values between 0 and @max_signal.
1019 * If possible please provide dB or dBm instead.
1021 * @IEEE80211_HW_SIGNAL_DBM:
1022 * Hardware gives signal values in dBm, decibel difference from
1023 * one milliwatt. This is the preferred method since it is standardized
1024 * between different devices. @max_signal does not need to be set.
1026 * @IEEE80211_HW_SPECTRUM_MGMT:
1027 * Hardware supports spectrum management defined in 802.11h
1028 * Measurement, Channel Switch, Quieting, TPC
1030 * @IEEE80211_HW_AMPDU_AGGREGATION:
1031 * Hardware supports 11n A-MPDU aggregation.
1033 * @IEEE80211_HW_SUPPORTS_PS:
1034 * Hardware has power save support (i.e. can go to sleep).
1036 * @IEEE80211_HW_PS_NULLFUNC_STACK:
1037 * Hardware requires nullfunc frame handling in stack, implies
1038 * stack support for dynamic PS.
1040 * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS:
1041 * Hardware has support for dynamic PS.
1043 * @IEEE80211_HW_MFP_CAPABLE:
1044 * Hardware supports management frame protection (MFP, IEEE 802.11w).
1046 * @IEEE80211_HW_BEACON_FILTER:
1047 * Hardware supports dropping of irrelevant beacon frames to
1048 * avoid waking up cpu.
1050 * @IEEE80211_HW_SUPPORTS_STATIC_SMPS:
1051 * Hardware supports static spatial multiplexing powersave,
1052 * ie. can turn off all but one chain even on HT connections
1053 * that should be using more chains.
1055 * @IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS:
1056 * Hardware supports dynamic spatial multiplexing powersave,
1057 * ie. can turn off all but one chain and then wake the rest
1058 * up as required after, for example, rts/cts handshake.
1060 * @IEEE80211_HW_SUPPORTS_UAPSD:
1061 * Hardware supports Unscheduled Automatic Power Save Delivery
1062 * (U-APSD) in managed mode. The mode is configured with
1063 * conf_tx() operation.
1065 * @IEEE80211_HW_REPORTS_TX_ACK_STATUS:
1066 * Hardware can provide ack status reports of Tx frames to
1069 * @IEEE80211_HW_CONNECTION_MONITOR:
1070 * The hardware performs its own connection monitoring, including
1071 * periodic keep-alives to the AP and probing the AP on beacon loss.
1072 * When this flag is set, signaling beacon-loss will cause an immediate
1073 * change to disassociated state.
1075 * @IEEE80211_HW_SUPPORTS_CQM_RSSI:
1076 * Hardware can do connection quality monitoring - i.e. it can monitor
1077 * connection quality related parameters, such as the RSSI level and
1078 * provide notifications if configured trigger levels are reached.
1080 * @IEEE80211_HW_NEED_DTIM_PERIOD:
1081 * This device needs to know the DTIM period for the BSS before
1084 * @IEEE80211_HW_SUPPORTS_PER_STA_GTK: The device's crypto engine supports
1085 * per-station GTKs as used by IBSS RSN or during fast transition. If
1086 * the device doesn't support per-station GTKs, but can be asked not
1087 * to decrypt group addressed frames, then IBSS RSN support is still
1088 * possible but software crypto will be used. Advertise the wiphy flag
1089 * only in that case.
1091 * @IEEE80211_HW_AP_LINK_PS: When operating in AP mode the device
1092 * autonomously manages the PS status of connected stations. When
1093 * this flag is set mac80211 will not trigger PS mode for connected
1094 * stations based on the PM bit of incoming frames.
1095 * Use ieee80211_start_ps()/ieee8021_end_ps() to manually configure
1096 * the PS mode of connected stations.
1098 enum ieee80211_hw_flags {
1099 IEEE80211_HW_HAS_RATE_CONTROL = 1<<0,
1100 IEEE80211_HW_RX_INCLUDES_FCS = 1<<1,
1101 IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2,
1102 IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3,
1103 IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4,
1104 IEEE80211_HW_SIGNAL_UNSPEC = 1<<5,
1105 IEEE80211_HW_SIGNAL_DBM = 1<<6,
1106 IEEE80211_HW_NEED_DTIM_PERIOD = 1<<7,
1107 IEEE80211_HW_SPECTRUM_MGMT = 1<<8,
1108 IEEE80211_HW_AMPDU_AGGREGATION = 1<<9,
1109 IEEE80211_HW_SUPPORTS_PS = 1<<10,
1110 IEEE80211_HW_PS_NULLFUNC_STACK = 1<<11,
1111 IEEE80211_HW_SUPPORTS_DYNAMIC_PS = 1<<12,
1112 IEEE80211_HW_MFP_CAPABLE = 1<<13,
1113 IEEE80211_HW_BEACON_FILTER = 1<<14,
1114 IEEE80211_HW_SUPPORTS_STATIC_SMPS = 1<<15,
1115 IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS = 1<<16,
1116 IEEE80211_HW_SUPPORTS_UAPSD = 1<<17,
1117 IEEE80211_HW_REPORTS_TX_ACK_STATUS = 1<<18,
1118 IEEE80211_HW_CONNECTION_MONITOR = 1<<19,
1119 IEEE80211_HW_SUPPORTS_CQM_RSSI = 1<<20,
1120 IEEE80211_HW_SUPPORTS_PER_STA_GTK = 1<<21,
1121 IEEE80211_HW_AP_LINK_PS = 1<<22,
1125 * struct ieee80211_hw - hardware information and state
1127 * This structure contains the configuration and hardware
1128 * information for an 802.11 PHY.
1130 * @wiphy: This points to the &struct wiphy allocated for this
1131 * 802.11 PHY. You must fill in the @perm_addr and @dev
1132 * members of this structure using SET_IEEE80211_DEV()
1133 * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported
1134 * bands (with channels, bitrates) are registered here.
1136 * @conf: &struct ieee80211_conf, device configuration, don't use.
1138 * @priv: pointer to private area that was allocated for driver use
1139 * along with this structure.
1141 * @flags: hardware flags, see &enum ieee80211_hw_flags.
1143 * @extra_tx_headroom: headroom to reserve in each transmit skb
1144 * for use by the driver (e.g. for transmit headers.)
1146 * @channel_change_time: time (in microseconds) it takes to change channels.
1148 * @max_signal: Maximum value for signal (rssi) in RX information, used
1149 * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
1151 * @max_listen_interval: max listen interval in units of beacon interval
1154 * @queues: number of available hardware transmit queues for
1155 * data packets. WMM/QoS requires at least four, these
1156 * queues need to have configurable access parameters.
1158 * @rate_control_algorithm: rate control algorithm for this hardware.
1159 * If unset (NULL), the default algorithm will be used. Must be
1160 * set before calling ieee80211_register_hw().
1162 * @vif_data_size: size (in bytes) of the drv_priv data area
1163 * within &struct ieee80211_vif.
1164 * @sta_data_size: size (in bytes) of the drv_priv data area
1165 * within &struct ieee80211_sta.
1167 * @max_rates: maximum number of alternate rate retry stages the hw
1169 * @max_report_rates: maximum number of alternate rate retry stages
1170 * the hw can report back.
1171 * @max_rate_tries: maximum number of tries for each stage
1173 * @napi_weight: weight used for NAPI polling. You must specify an
1174 * appropriate value here if a napi_poll operation is provided
1177 * @max_rx_aggregation_subframes: maximum buffer size (number of
1178 * sub-frames) to be used for A-MPDU block ack receiver
1180 * This is only relevant if the device has restrictions on the
1181 * number of subframes, if it relies on mac80211 to do reordering
1182 * it shouldn't be set.
1184 * @max_tx_aggregation_subframes: maximum number of subframes in an
1185 * aggregate an HT driver will transmit, used by the peer as a
1186 * hint to size its reorder buffer.
1188 struct ieee80211_hw {
1189 struct ieee80211_conf conf;
1190 struct wiphy *wiphy;
1191 const char *rate_control_algorithm;
1194 unsigned int extra_tx_headroom;
1195 int channel_change_time;
1200 u16 max_listen_interval;
1203 u8 max_report_rates;
1205 u8 max_rx_aggregation_subframes;
1206 u8 max_tx_aggregation_subframes;
1210 * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy
1212 * @wiphy: the &struct wiphy which we want to query
1214 * mac80211 drivers can use this to get to their respective
1215 * &struct ieee80211_hw. Drivers wishing to get to their own private
1216 * structure can then access it via hw->priv. Note that mac802111 drivers should
1217 * not use wiphy_priv() to try to get their private driver structure as this
1218 * is already used internally by mac80211.
1220 struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy);
1223 * SET_IEEE80211_DEV - set device for 802.11 hardware
1225 * @hw: the &struct ieee80211_hw to set the device for
1226 * @dev: the &struct device of this 802.11 device
1228 static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev)
1230 set_wiphy_dev(hw->wiphy, dev);
1234 * SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware
1236 * @hw: the &struct ieee80211_hw to set the MAC address for
1237 * @addr: the address to set
1239 static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr)
1241 memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
1244 static inline struct ieee80211_rate *
1245 ieee80211_get_tx_rate(const struct ieee80211_hw *hw,
1246 const struct ieee80211_tx_info *c)
1248 if (WARN_ON(c->control.rates[0].idx < 0))
1250 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx];
1253 static inline struct ieee80211_rate *
1254 ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw,
1255 const struct ieee80211_tx_info *c)
1257 if (c->control.rts_cts_rate_idx < 0)
1259 return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx];
1262 static inline struct ieee80211_rate *
1263 ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw,
1264 const struct ieee80211_tx_info *c, int idx)
1266 if (c->control.rates[idx + 1].idx < 0)
1268 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx];
1272 * DOC: Hardware crypto acceleration
1274 * mac80211 is capable of taking advantage of many hardware
1275 * acceleration designs for encryption and decryption operations.
1277 * The set_key() callback in the &struct ieee80211_ops for a given
1278 * device is called to enable hardware acceleration of encryption and
1279 * decryption. The callback takes a @sta parameter that will be NULL
1280 * for default keys or keys used for transmission only, or point to
1281 * the station information for the peer for individual keys.
1282 * Multiple transmission keys with the same key index may be used when
1283 * VLANs are configured for an access point.
1285 * When transmitting, the TX control data will use the @hw_key_idx
1286 * selected by the driver by modifying the &struct ieee80211_key_conf
1287 * pointed to by the @key parameter to the set_key() function.
1289 * The set_key() call for the %SET_KEY command should return 0 if
1290 * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be
1291 * added; if you return 0 then hw_key_idx must be assigned to the
1292 * hardware key index, you are free to use the full u8 range.
1294 * When the cmd is %DISABLE_KEY then it must succeed.
1296 * Note that it is permissible to not decrypt a frame even if a key
1297 * for it has been uploaded to hardware, the stack will not make any
1298 * decision based on whether a key has been uploaded or not but rather
1299 * based on the receive flags.
1301 * The &struct ieee80211_key_conf structure pointed to by the @key
1302 * parameter is guaranteed to be valid until another call to set_key()
1303 * removes it, but it can only be used as a cookie to differentiate
1306 * In TKIP some HW need to be provided a phase 1 key, for RX decryption
1307 * acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key
1309 * The update_tkip_key() call updates the driver with the new phase 1 key.
1310 * This happens every time the iv16 wraps around (every 65536 packets). The
1311 * set_key() call will happen only once for each key (unless the AP did
1312 * rekeying), it will not include a valid phase 1 key. The valid phase 1 key is
1313 * provided by update_tkip_key only. The trigger that makes mac80211 call this
1314 * handler is software decryption with wrap around of iv16.
1318 * DOC: Powersave support
1320 * mac80211 has support for various powersave implementations.
1322 * First, it can support hardware that handles all powersaving by itself,
1323 * such hardware should simply set the %IEEE80211_HW_SUPPORTS_PS hardware
1324 * flag. In that case, it will be told about the desired powersave mode
1325 * with the %IEEE80211_CONF_PS flag depending on the association status.
1326 * The hardware must take care of sending nullfunc frames when necessary,
1327 * i.e. when entering and leaving powersave mode. The hardware is required
1328 * to look at the AID in beacons and signal to the AP that it woke up when
1329 * it finds traffic directed to it.
1331 * %IEEE80211_CONF_PS flag enabled means that the powersave mode defined in
1332 * IEEE 802.11-2007 section 11.2 is enabled. This is not to be confused
1333 * with hardware wakeup and sleep states. Driver is responsible for waking
1334 * up the hardware before issuing commands to the hardware and putting it
1335 * back to sleep at appropriate times.
1337 * When PS is enabled, hardware needs to wakeup for beacons and receive the
1338 * buffered multicast/broadcast frames after the beacon. Also it must be
1339 * possible to send frames and receive the acknowledment frame.
1341 * Other hardware designs cannot send nullfunc frames by themselves and also
1342 * need software support for parsing the TIM bitmap. This is also supported
1343 * by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS and
1344 * %IEEE80211_HW_PS_NULLFUNC_STACK flags. The hardware is of course still
1345 * required to pass up beacons. The hardware is still required to handle
1346 * waking up for multicast traffic; if it cannot the driver must handle that
1347 * as best as it can, mac80211 is too slow to do that.
1349 * Dynamic powersave is an extension to normal powersave in which the
1350 * hardware stays awake for a user-specified period of time after sending a
1351 * frame so that reply frames need not be buffered and therefore delayed to
1352 * the next wakeup. It's compromise of getting good enough latency when
1353 * there's data traffic and still saving significantly power in idle
1356 * Dynamic powersave is simply supported by mac80211 enabling and disabling
1357 * PS based on traffic. Driver needs to only set %IEEE80211_HW_SUPPORTS_PS
1358 * flag and mac80211 will handle everything automatically. Additionally,
1359 * hardware having support for the dynamic PS feature may set the
1360 * %IEEE80211_HW_SUPPORTS_DYNAMIC_PS flag to indicate that it can support
1361 * dynamic PS mode itself. The driver needs to look at the
1362 * @dynamic_ps_timeout hardware configuration value and use it that value
1363 * whenever %IEEE80211_CONF_PS is set. In this case mac80211 will disable
1364 * dynamic PS feature in stack and will just keep %IEEE80211_CONF_PS
1365 * enabled whenever user has enabled powersave.
1367 * Some hardware need to toggle a single shared antenna between WLAN and
1368 * Bluetooth to facilitate co-existence. These types of hardware set
1369 * limitations on the use of host controlled dynamic powersave whenever there
1370 * is simultaneous WLAN and Bluetooth traffic. For these types of hardware, the
1371 * driver may request temporarily going into full power save, in order to
1372 * enable toggling the antenna between BT and WLAN. If the driver requests
1373 * disabling dynamic powersave, the @dynamic_ps_timeout value will be
1374 * temporarily set to zero until the driver re-enables dynamic powersave.
1376 * Driver informs U-APSD client support by enabling
1377 * %IEEE80211_HW_SUPPORTS_UAPSD flag. The mode is configured through the
1378 * uapsd paramater in conf_tx() operation. Hardware needs to send the QoS
1379 * Nullfunc frames and stay awake until the service period has ended. To
1380 * utilize U-APSD, dynamic powersave is disabled for voip AC and all frames
1381 * from that AC are transmitted with powersave enabled.
1383 * Note: U-APSD client mode is not yet supported with
1384 * %IEEE80211_HW_PS_NULLFUNC_STACK.
1388 * DOC: Beacon filter support
1390 * Some hardware have beacon filter support to reduce host cpu wakeups
1391 * which will reduce system power consumption. It usuallly works so that
1392 * the firmware creates a checksum of the beacon but omits all constantly
1393 * changing elements (TSF, TIM etc). Whenever the checksum changes the
1394 * beacon is forwarded to the host, otherwise it will be just dropped. That
1395 * way the host will only receive beacons where some relevant information
1396 * (for example ERP protection or WMM settings) have changed.
1398 * Beacon filter support is advertised with the %IEEE80211_HW_BEACON_FILTER
1399 * hardware capability. The driver needs to enable beacon filter support
1400 * whenever power save is enabled, that is %IEEE80211_CONF_PS is set. When
1401 * power save is enabled, the stack will not check for beacon loss and the
1402 * driver needs to notify about loss of beacons with ieee80211_beacon_loss().
1404 * The time (or number of beacons missed) until the firmware notifies the
1405 * driver of a beacon loss event (which in turn causes the driver to call
1406 * ieee80211_beacon_loss()) should be configurable and will be controlled
1407 * by mac80211 and the roaming algorithm in the future.
1409 * Since there may be constantly changing information elements that nothing
1410 * in the software stack cares about, we will, in the future, have mac80211
1411 * tell the driver which information elements are interesting in the sense
1412 * that we want to see changes in them. This will include
1413 * - a list of information element IDs
1414 * - a list of OUIs for the vendor information element
1416 * Ideally, the hardware would filter out any beacons without changes in the
1417 * requested elements, but if it cannot support that it may, at the expense
1418 * of some efficiency, filter out only a subset. For example, if the device
1419 * doesn't support checking for OUIs it should pass up all changes in all
1420 * vendor information elements.
1422 * Note that change, for the sake of simplification, also includes information
1423 * elements appearing or disappearing from the beacon.
1425 * Some hardware supports an "ignore list" instead, just make sure nothing
1426 * that was requested is on the ignore list, and include commonly changing
1427 * information element IDs in the ignore list, for example 11 (BSS load) and
1428 * the various vendor-assigned IEs with unknown contents (128, 129, 133-136,
1429 * 149, 150, 155, 156, 173, 176, 178, 179, 219); for forward compatibility
1430 * it could also include some currently unused IDs.
1433 * In addition to these capabilities, hardware should support notifying the
1434 * host of changes in the beacon RSSI. This is relevant to implement roaming
1435 * when no traffic is flowing (when traffic is flowing we see the RSSI of
1436 * the received data packets). This can consist in notifying the host when
1437 * the RSSI changes significantly or when it drops below or rises above
1438 * configurable thresholds. In the future these thresholds will also be
1439 * configured by mac80211 (which gets them from userspace) to implement
1440 * them as the roaming algorithm requires.
1442 * If the hardware cannot implement this, the driver should ask it to
1443 * periodically pass beacon frames to the host so that software can do the
1444 * signal strength threshold checking.
1448 * DOC: Spatial multiplexing power save
1450 * SMPS (Spatial multiplexing power save) is a mechanism to conserve
1451 * power in an 802.11n implementation. For details on the mechanism
1452 * and rationale, please refer to 802.11 (as amended by 802.11n-2009)
1453 * "11.2.3 SM power save".
1455 * The mac80211 implementation is capable of sending action frames
1456 * to update the AP about the station's SMPS mode, and will instruct
1457 * the driver to enter the specific mode. It will also announce the
1458 * requested SMPS mode during the association handshake. Hardware
1459 * support for this feature is required, and can be indicated by
1462 * The default mode will be "automatic", which nl80211/cfg80211
1463 * defines to be dynamic SMPS in (regular) powersave, and SMPS
1464 * turned off otherwise.
1466 * To support this feature, the driver must set the appropriate
1467 * hardware support flags, and handle the SMPS flag to the config()
1468 * operation. It will then with this mechanism be instructed to
1469 * enter the requested SMPS mode while associated to an HT AP.
1473 * DOC: Frame filtering
1475 * mac80211 requires to see many management frames for proper
1476 * operation, and users may want to see many more frames when
1477 * in monitor mode. However, for best CPU usage and power consumption,
1478 * having as few frames as possible percolate through the stack is
1479 * desirable. Hence, the hardware should filter as much as possible.
1481 * To achieve this, mac80211 uses filter flags (see below) to tell
1482 * the driver's configure_filter() function which frames should be
1483 * passed to mac80211 and which should be filtered out.
1485 * Before configure_filter() is invoked, the prepare_multicast()
1486 * callback is invoked with the parameters @mc_count and @mc_list
1487 * for the combined multicast address list of all virtual interfaces.
1488 * It's use is optional, and it returns a u64 that is passed to
1489 * configure_filter(). Additionally, configure_filter() has the
1490 * arguments @changed_flags telling which flags were changed and
1491 * @total_flags with the new flag states.
1493 * If your device has no multicast address filters your driver will
1494 * need to check both the %FIF_ALLMULTI flag and the @mc_count
1495 * parameter to see whether multicast frames should be accepted
1498 * All unsupported flags in @total_flags must be cleared.
1499 * Hardware does not support a flag if it is incapable of _passing_
1500 * the frame to the stack. Otherwise the driver must ignore
1501 * the flag, but not clear it.
1502 * You must _only_ clear the flag (announce no support for the
1503 * flag to mac80211) if you are not able to pass the packet type
1504 * to the stack (so the hardware always filters it).
1505 * So for example, you should clear @FIF_CONTROL, if your hardware
1506 * always filters control frames. If your hardware always passes
1507 * control frames to the kernel and is incapable of filtering them,
1508 * you do _not_ clear the @FIF_CONTROL flag.
1509 * This rule applies to all other FIF flags as well.
1513 * enum ieee80211_filter_flags - hardware filter flags
1515 * These flags determine what the filter in hardware should be
1516 * programmed to let through and what should not be passed to the
1517 * stack. It is always safe to pass more frames than requested,
1518 * but this has negative impact on power consumption.
1520 * @FIF_PROMISC_IN_BSS: promiscuous mode within your BSS,
1521 * think of the BSS as your network segment and then this corresponds
1522 * to the regular ethernet device promiscuous mode.
1524 * @FIF_ALLMULTI: pass all multicast frames, this is used if requested
1525 * by the user or if the hardware is not capable of filtering by
1526 * multicast address.
1528 * @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the
1529 * %RX_FLAG_FAILED_FCS_CRC for them)
1531 * @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set
1532 * the %RX_FLAG_FAILED_PLCP_CRC for them
1534 * @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate
1535 * to the hardware that it should not filter beacons or probe responses
1536 * by BSSID. Filtering them can greatly reduce the amount of processing
1537 * mac80211 needs to do and the amount of CPU wakeups, so you should
1538 * honour this flag if possible.
1540 * @FIF_CONTROL: pass control frames (except for PS Poll), if PROMISC_IN_BSS
1541 * is not set then only those addressed to this station.
1543 * @FIF_OTHER_BSS: pass frames destined to other BSSes
1545 * @FIF_PSPOLL: pass PS Poll frames, if PROMISC_IN_BSS is not set then only
1546 * those addressed to this station.
1548 * @FIF_PROBE_REQ: pass probe request frames
1550 enum ieee80211_filter_flags {
1551 FIF_PROMISC_IN_BSS = 1<<0,
1552 FIF_ALLMULTI = 1<<1,
1554 FIF_PLCPFAIL = 1<<3,
1555 FIF_BCN_PRBRESP_PROMISC = 1<<4,
1557 FIF_OTHER_BSS = 1<<6,
1559 FIF_PROBE_REQ = 1<<8,
1563 * enum ieee80211_ampdu_mlme_action - A-MPDU actions
1565 * These flags are used with the ampdu_action() callback in
1566 * &struct ieee80211_ops to indicate which action is needed.
1568 * Note that drivers MUST be able to deal with a TX aggregation
1569 * session being stopped even before they OK'ed starting it by
1570 * calling ieee80211_start_tx_ba_cb_irqsafe, because the peer
1571 * might receive the addBA frame and send a delBA right away!
1573 * @IEEE80211_AMPDU_RX_START: start Rx aggregation
1574 * @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation
1575 * @IEEE80211_AMPDU_TX_START: start Tx aggregation
1576 * @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation
1577 * @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational
1579 enum ieee80211_ampdu_mlme_action {
1580 IEEE80211_AMPDU_RX_START,
1581 IEEE80211_AMPDU_RX_STOP,
1582 IEEE80211_AMPDU_TX_START,
1583 IEEE80211_AMPDU_TX_STOP,
1584 IEEE80211_AMPDU_TX_OPERATIONAL,
1588 * enum ieee80211_tx_sync_type - TX sync type
1589 * @IEEE80211_TX_SYNC_AUTH: sync TX for authentication
1590 * (and possibly also before direct probe)
1591 * @IEEE80211_TX_SYNC_ASSOC: sync TX for association
1592 * @IEEE80211_TX_SYNC_ACTION: sync TX for action frame
1593 * (not implemented yet)
1595 enum ieee80211_tx_sync_type {
1596 IEEE80211_TX_SYNC_AUTH,
1597 IEEE80211_TX_SYNC_ASSOC,
1598 IEEE80211_TX_SYNC_ACTION,
1602 * struct ieee80211_ops - callbacks from mac80211 to the driver
1604 * This structure contains various callbacks that the driver may
1605 * handle or, in some cases, must handle, for example to configure
1606 * the hardware to a new channel or to transmit a frame.
1608 * @tx: Handler that 802.11 module calls for each transmitted frame.
1609 * skb contains the buffer starting from the IEEE 802.11 header.
1610 * The low-level driver should send the frame out based on
1611 * configuration in the TX control data. This handler should,
1612 * preferably, never fail and stop queues appropriately, more
1613 * importantly, however, it must never fail for A-MPDU-queues.
1614 * This function should return NETDEV_TX_OK except in very
1616 * Must be implemented and atomic.
1618 * @start: Called before the first netdevice attached to the hardware
1619 * is enabled. This should turn on the hardware and must turn on
1620 * frame reception (for possibly enabled monitor interfaces.)
1621 * Returns negative error codes, these may be seen in userspace,
1623 * When the device is started it should not have a MAC address
1624 * to avoid acknowledging frames before a non-monitor device
1626 * Must be implemented and can sleep.
1628 * @stop: Called after last netdevice attached to the hardware
1629 * is disabled. This should turn off the hardware (at least
1630 * it must turn off frame reception.)
1631 * May be called right after add_interface if that rejects
1632 * an interface. If you added any work onto the mac80211 workqueue
1633 * you should ensure to cancel it on this callback.
1634 * Must be implemented and can sleep.
1636 * @suspend: Suspend the device; mac80211 itself will quiesce before and
1637 * stop transmitting and doing any other configuration, and then
1638 * ask the device to suspend. This is only invoked when WoWLAN is
1639 * configured, otherwise the device is deconfigured completely and
1640 * reconfigured at resume time.
1641 * The driver may also impose special conditions under which it
1642 * wants to use the "normal" suspend (deconfigure), say if it only
1643 * supports WoWLAN when the device is associated. In this case, it
1644 * must return 1 from this function.
1646 * @resume: If WoWLAN was configured, this indicates that mac80211 is
1647 * now resuming its operation, after this the device must be fully
1648 * functional again. If this returns an error, the only way out is
1649 * to also unregister the device. If it returns 1, then mac80211
1650 * will also go through the regular complete restart on resume.
1652 * @add_interface: Called when a netdevice attached to the hardware is
1653 * enabled. Because it is not called for monitor mode devices, @start
1654 * and @stop must be implemented.
1655 * The driver should perform any initialization it needs before
1656 * the device can be enabled. The initial configuration for the
1657 * interface is given in the conf parameter.
1658 * The callback may refuse to add an interface by returning a
1659 * negative error code (which will be seen in userspace.)
1660 * Must be implemented and can sleep.
1662 * @change_interface: Called when a netdevice changes type. This callback
1663 * is optional, but only if it is supported can interface types be
1664 * switched while the interface is UP. The callback may sleep.
1665 * Note that while an interface is being switched, it will not be
1666 * found by the interface iteration callbacks.
1668 * @remove_interface: Notifies a driver that an interface is going down.
1669 * The @stop callback is called after this if it is the last interface
1670 * and no monitor interfaces are present.
1671 * When all interfaces are removed, the MAC address in the hardware
1672 * must be cleared so the device no longer acknowledges packets,
1673 * the mac_addr member of the conf structure is, however, set to the
1674 * MAC address of the device going away.
1675 * Hence, this callback must be implemented. It can sleep.
1677 * @config: Handler for configuration requests. IEEE 802.11 code calls this
1678 * function to change hardware configuration, e.g., channel.
1679 * This function should never fail but returns a negative error code
1680 * if it does. The callback can sleep.
1682 * @bss_info_changed: Handler for configuration requests related to BSS
1683 * parameters that may vary during BSS's lifespan, and may affect low
1684 * level driver (e.g. assoc/disassoc status, erp parameters).
1685 * This function should not be used if no BSS has been set, unless
1686 * for association indication. The @changed parameter indicates which
1687 * of the bss parameters has changed when a call is made. The callback
1690 * @tx_sync: Called before a frame is sent to an AP/GO. In the GO case, the
1691 * driver should sync with the GO's powersaving so the device doesn't
1692 * transmit the frame while the GO is asleep. In the regular AP case
1693 * it may be used by drivers for devices implementing other restrictions
1694 * on talking to APs, e.g. due to regulatory enforcement or just HW
1696 * This function is called for every authentication, association and
1697 * action frame separately since applications might attempt to auth
1698 * with multiple APs before chosing one to associate to. If it returns
1699 * an error, the corresponding authentication, association or frame
1700 * transmission is aborted and reported as having failed. It is always
1701 * called after tuning to the correct channel.
1702 * The callback might be called multiple times before @finish_tx_sync
1703 * (but @finish_tx_sync will be called once for each) but in practice
1704 * this is unlikely to happen. It can also refuse in that case if the
1705 * driver cannot handle that situation.
1706 * This callback can sleep.
1707 * @finish_tx_sync: Called as a counterpart to @tx_sync, unless that returned
1708 * an error. This callback can sleep.
1710 * @prepare_multicast: Prepare for multicast filter configuration.
1711 * This callback is optional, and its return value is passed
1712 * to configure_filter(). This callback must be atomic.
1714 * @configure_filter: Configure the device's RX filter.
1715 * See the section "Frame filtering" for more information.
1716 * This callback must be implemented and can sleep.
1718 * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit
1719 * must be set or cleared for a given STA. Must be atomic.
1721 * @set_key: See the section "Hardware crypto acceleration"
1722 * This callback is only called between add_interface and
1723 * remove_interface calls, i.e. while the given virtual interface
1725 * Returns a negative error code if the key can't be added.
1726 * The callback can sleep.
1728 * @update_tkip_key: See the section "Hardware crypto acceleration"
1729 * This callback will be called in the context of Rx. Called for drivers
1730 * which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY.
1731 * The callback must be atomic.
1733 * @set_rekey_data: If the device supports GTK rekeying, for example while the
1734 * host is suspended, it can assign this callback to retrieve the data
1735 * necessary to do GTK rekeying, this is the KEK, KCK and replay counter.
1736 * After rekeying was done it should (for example during resume) notify
1737 * userspace of the new replay counter using ieee80211_gtk_rekey_notify().
1739 * @hw_scan: Ask the hardware to service the scan request, no need to start
1740 * the scan state machine in stack. The scan must honour the channel
1741 * configuration done by the regulatory agent in the wiphy's
1742 * registered bands. The hardware (or the driver) needs to make sure
1743 * that power save is disabled.
1744 * The @req ie/ie_len members are rewritten by mac80211 to contain the
1745 * entire IEs after the SSID, so that drivers need not look at these
1746 * at all but just send them after the SSID -- mac80211 includes the
1747 * (extended) supported rates and HT information (where applicable).
1748 * When the scan finishes, ieee80211_scan_completed() must be called;
1749 * note that it also must be called when the scan cannot finish due to
1750 * any error unless this callback returned a negative error code.
1751 * The callback can sleep.
1753 * @cancel_hw_scan: Ask the low-level tp cancel the active hw scan.
1754 * The driver should ask the hardware to cancel the scan (if possible),
1755 * but the scan will be completed only after the driver will call
1756 * ieee80211_scan_completed().
1757 * This callback is needed for wowlan, to prevent enqueueing a new
1758 * scan_work after the low-level driver was already suspended.
1759 * The callback can sleep.
1761 * @sched_scan_start: Ask the hardware to start scanning repeatedly at
1762 * specific intervals. The driver must call the
1763 * ieee80211_sched_scan_results() function whenever it finds results.
1764 * This process will continue until sched_scan_stop is called.
1766 * @sched_scan_stop: Tell the hardware to stop an ongoing scheduled scan.
1768 * @sw_scan_start: Notifier function that is called just before a software scan
1769 * is started. Can be NULL, if the driver doesn't need this notification.
1770 * The callback can sleep.
1772 * @sw_scan_complete: Notifier function that is called just after a
1773 * software scan finished. Can be NULL, if the driver doesn't need
1774 * this notification.
1775 * The callback can sleep.
1777 * @get_stats: Return low-level statistics.
1778 * Returns zero if statistics are available.
1779 * The callback can sleep.
1781 * @get_tkip_seq: If your device implements TKIP encryption in hardware this
1782 * callback should be provided to read the TKIP transmit IVs (both IV32
1783 * and IV16) for the given key from hardware.
1784 * The callback must be atomic.
1786 * @set_frag_threshold: Configuration of fragmentation threshold. Assign this
1787 * if the device does fragmentation by itself; if this callback is
1788 * implemented then the stack will not do fragmentation.
1789 * The callback can sleep.
1791 * @set_rts_threshold: Configuration of RTS threshold (if device needs it)
1792 * The callback can sleep.
1794 * @sta_add: Notifies low level driver about addition of an associated station,
1795 * AP, IBSS/WDS/mesh peer etc. This callback can sleep.
1797 * @sta_remove: Notifies low level driver about removal of an associated
1798 * station, AP, IBSS/WDS/mesh peer etc. This callback can sleep.
1800 * @sta_notify: Notifies low level driver about power state transition of an
1801 * associated station, AP, IBSS/WDS/mesh peer etc. For a VIF operating
1802 * in AP mode, this callback will not be called when the flag
1803 * %IEEE80211_HW_AP_LINK_PS is set. Must be atomic.
1805 * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
1806 * bursting) for a hardware TX queue.
1807 * Returns a negative error code on failure.
1808 * The callback can sleep.
1810 * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
1811 * this is only used for IBSS mode BSSID merging and debugging. Is not a
1812 * required function.
1813 * The callback can sleep.
1815 * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
1816 * Currently, this is only used for IBSS mode debugging. Is not a
1817 * required function.
1818 * The callback can sleep.
1820 * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize
1821 * with other STAs in the IBSS. This is only used in IBSS mode. This
1822 * function is optional if the firmware/hardware takes full care of
1823 * TSF synchronization.
1824 * The callback can sleep.
1826 * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us.
1827 * This is needed only for IBSS mode and the result of this function is
1828 * used to determine whether to reply to Probe Requests.
1829 * Returns non-zero if this device sent the last beacon.
1830 * The callback can sleep.
1832 * @ampdu_action: Perform a certain A-MPDU action
1833 * The RA/TID combination determines the destination and TID we want
1834 * the ampdu action to be performed for. The action is defined through
1835 * ieee80211_ampdu_mlme_action. Starting sequence number (@ssn)
1836 * is the first frame we expect to perform the action on. Notice
1837 * that TX/RX_STOP can pass NULL for this parameter.
1838 * The @buf_size parameter is only valid when the action is set to
1839 * %IEEE80211_AMPDU_TX_OPERATIONAL and indicates the peer's reorder
1840 * buffer size (number of subframes) for this session -- the driver
1841 * may neither send aggregates containing more subframes than this
1842 * nor send aggregates in a way that lost frames would exceed the
1843 * buffer size. If just limiting the aggregate size, this would be
1844 * possible with a buf_size of 8:
1846 * - RX: 2....7 (lost frame #1)
1848 * which is invalid since #1 was now re-transmitted well past the
1849 * buffer size of 8. Correct ways to retransmit #1 would be:
1850 * - TX: 1 or 18 or 81
1851 * Even "189" would be wrong since 1 could be lost again.
1853 * Returns a negative error code on failure.
1854 * The callback can sleep.
1856 * @get_survey: Return per-channel survey information
1858 * @rfkill_poll: Poll rfkill hardware state. If you need this, you also
1859 * need to set wiphy->rfkill_poll to %true before registration,
1860 * and need to call wiphy_rfkill_set_hw_state() in the callback.
1861 * The callback can sleep.
1863 * @set_coverage_class: Set slot time for given coverage class as specified
1864 * in IEEE 802.11-2007 section 17.3.8.6 and modify ACK timeout
1865 * accordingly. This callback is not required and may sleep.
1867 * @testmode_cmd: Implement a cfg80211 test mode command.
1868 * The callback can sleep.
1869 * @testmode_dump: Implement a cfg80211 test mode dump. The callback can sleep.
1871 * @flush: Flush all pending frames from the hardware queue, making sure
1872 * that the hardware queues are empty. If the parameter @drop is set
1873 * to %true, pending frames may be dropped. The callback can sleep.
1875 * @channel_switch: Drivers that need (or want) to offload the channel
1876 * switch operation for CSAs received from the AP may implement this
1877 * callback. They must then call ieee80211_chswitch_done() to indicate
1878 * completion of the channel switch.
1880 * @napi_poll: Poll Rx queue for incoming data frames.
1882 * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device.
1883 * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may
1884 * reject TX/RX mask combinations they cannot support by returning -EINVAL
1885 * (also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX).
1887 * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant).
1889 * @remain_on_channel: Starts an off-channel period on the given channel, must
1890 * call back to ieee80211_ready_on_channel() when on that channel. Note
1891 * that normal channel traffic is not stopped as this is intended for hw
1892 * offload. Frames to transmit on the off-channel channel are transmitted
1893 * normally except for the %IEEE80211_TX_CTL_TX_OFFCHAN flag. When the
1894 * duration (which will always be non-zero) expires, the driver must call
1895 * ieee80211_remain_on_channel_expired(). This callback may sleep.
1896 * @cancel_remain_on_channel: Requests that an ongoing off-channel period is
1897 * aborted before it expires. This callback may sleep.
1898 * @offchannel_tx: Transmit frame on another channel, wait for a response
1899 * and return. Reliable TX status must be reported for the frame. If the
1900 * return value is 1, then the @remain_on_channel will be used with a
1901 * regular transmission (if supported.)
1902 * @offchannel_tx_cancel_wait: cancel wait associated with offchannel TX
1904 * @set_ringparam: Set tx and rx ring sizes.
1906 * @get_ringparam: Get tx and rx ring current and maximum sizes.
1908 * @tx_frames_pending: Check if there is any pending frame in the hardware
1909 * queues before entering power save.
1911 * @set_bitrate_mask: Set a mask of rates to be used for rate control selection
1912 * when transmitting a frame. Currently only legacy rates are handled.
1913 * The callback can sleep.
1914 * @rssi_callback: Notify driver when the average RSSI goes above/below
1915 * thresholds that were registered previously. The callback can sleep.
1917 struct ieee80211_ops {
1918 void (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb);
1919 int (*start)(struct ieee80211_hw *hw);
1920 void (*stop)(struct ieee80211_hw *hw);
1922 int (*suspend)(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan);
1923 int (*resume)(struct ieee80211_hw *hw);
1925 int (*add_interface)(struct ieee80211_hw *hw,
1926 struct ieee80211_vif *vif);
1927 int (*change_interface)(struct ieee80211_hw *hw,
1928 struct ieee80211_vif *vif,
1929 enum nl80211_iftype new_type, bool p2p);
1930 void (*remove_interface)(struct ieee80211_hw *hw,
1931 struct ieee80211_vif *vif);
1932 int (*config)(struct ieee80211_hw *hw, u32 changed);
1933 void (*bss_info_changed)(struct ieee80211_hw *hw,
1934 struct ieee80211_vif *vif,
1935 struct ieee80211_bss_conf *info,
1938 int (*tx_sync)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
1939 const u8 *bssid, enum ieee80211_tx_sync_type type);
1940 void (*finish_tx_sync)(struct ieee80211_hw *hw,
1941 struct ieee80211_vif *vif,
1943 enum ieee80211_tx_sync_type type);
1945 u64 (*prepare_multicast)(struct ieee80211_hw *hw,
1946 struct netdev_hw_addr_list *mc_list);
1947 void (*configure_filter)(struct ieee80211_hw *hw,
1948 unsigned int changed_flags,
1949 unsigned int *total_flags,
1951 int (*set_tim)(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
1953 int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd,
1954 struct ieee80211_vif *vif, struct ieee80211_sta *sta,
1955 struct ieee80211_key_conf *key);
1956 void (*update_tkip_key)(struct ieee80211_hw *hw,
1957 struct ieee80211_vif *vif,
1958 struct ieee80211_key_conf *conf,
1959 struct ieee80211_sta *sta,
1960 u32 iv32, u16 *phase1key);
1961 void (*set_rekey_data)(struct ieee80211_hw *hw,
1962 struct ieee80211_vif *vif,
1963 struct cfg80211_gtk_rekey_data *data);
1964 int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
1965 struct cfg80211_scan_request *req);
1966 void (*cancel_hw_scan)(struct ieee80211_hw *hw,
1967 struct ieee80211_vif *vif);
1968 int (*sched_scan_start)(struct ieee80211_hw *hw,
1969 struct ieee80211_vif *vif,
1970 struct cfg80211_sched_scan_request *req,
1971 struct ieee80211_sched_scan_ies *ies);
1972 void (*sched_scan_stop)(struct ieee80211_hw *hw,
1973 struct ieee80211_vif *vif);
1974 void (*sw_scan_start)(struct ieee80211_hw *hw);
1975 void (*sw_scan_complete)(struct ieee80211_hw *hw);
1976 int (*get_stats)(struct ieee80211_hw *hw,
1977 struct ieee80211_low_level_stats *stats);
1978 void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx,
1979 u32 *iv32, u16 *iv16);
1980 int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value);
1981 int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);
1982 int (*sta_add)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
1983 struct ieee80211_sta *sta);
1984 int (*sta_remove)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
1985 struct ieee80211_sta *sta);
1986 void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
1987 enum sta_notify_cmd, struct ieee80211_sta *sta);
1988 int (*conf_tx)(struct ieee80211_hw *hw, u16 queue,
1989 const struct ieee80211_tx_queue_params *params);
1990 u64 (*get_tsf)(struct ieee80211_hw *hw);
1991 void (*set_tsf)(struct ieee80211_hw *hw, u64 tsf);
1992 void (*reset_tsf)(struct ieee80211_hw *hw);
1993 int (*tx_last_beacon)(struct ieee80211_hw *hw);
1994 int (*ampdu_action)(struct ieee80211_hw *hw,
1995 struct ieee80211_vif *vif,
1996 enum ieee80211_ampdu_mlme_action action,
1997 struct ieee80211_sta *sta, u16 tid, u16 *ssn,
1999 int (*get_survey)(struct ieee80211_hw *hw, int idx,
2000 struct survey_info *survey);
2001 void (*rfkill_poll)(struct ieee80211_hw *hw);
2002 void (*set_coverage_class)(struct ieee80211_hw *hw, u8 coverage_class);
2003 #ifdef CONFIG_NL80211_TESTMODE
2004 int (*testmode_cmd)(struct ieee80211_hw *hw, void *data, int len);
2005 int (*testmode_dump)(struct ieee80211_hw *hw, struct sk_buff *skb,
2006 struct netlink_callback *cb,
2007 void *data, int len);
2009 void (*flush)(struct ieee80211_hw *hw, bool drop);
2010 void (*channel_switch)(struct ieee80211_hw *hw,
2011 struct ieee80211_channel_switch *ch_switch);
2012 int (*napi_poll)(struct ieee80211_hw *hw, int budget);
2013 int (*set_antenna)(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant);
2014 int (*get_antenna)(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant);
2016 int (*remain_on_channel)(struct ieee80211_hw *hw,
2017 struct ieee80211_channel *chan,
2018 enum nl80211_channel_type channel_type,
2020 int (*cancel_remain_on_channel)(struct ieee80211_hw *hw);
2021 int (*offchannel_tx)(struct ieee80211_hw *hw, struct sk_buff *skb,
2022 struct ieee80211_channel *chan,
2023 enum nl80211_channel_type channel_type,
2025 int (*offchannel_tx_cancel_wait)(struct ieee80211_hw *hw);
2026 int (*set_ringparam)(struct ieee80211_hw *hw, u32 tx, u32 rx);
2027 void (*get_ringparam)(struct ieee80211_hw *hw,
2028 u32 *tx, u32 *tx_max, u32 *rx, u32 *rx_max);
2029 bool (*tx_frames_pending)(struct ieee80211_hw *hw);
2030 int (*set_bitrate_mask)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
2031 const struct cfg80211_bitrate_mask *mask);
2032 void (*rssi_callback)(struct ieee80211_hw *hw,
2033 enum ieee80211_rssi_event rssi_event);
2037 * ieee80211_alloc_hw - Allocate a new hardware device
2039 * This must be called once for each hardware device. The returned pointer
2040 * must be used to refer to this device when calling other functions.
2041 * mac80211 allocates a private data area for the driver pointed to by
2042 * @priv in &struct ieee80211_hw, the size of this area is given as
2045 * @priv_data_len: length of private data
2046 * @ops: callbacks for this device
2048 struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len,
2049 const struct ieee80211_ops *ops);
2052 * ieee80211_register_hw - Register hardware device
2054 * You must call this function before any other functions in
2055 * mac80211. Note that before a hardware can be registered, you
2056 * need to fill the contained wiphy's information.
2058 * @hw: the device to register as returned by ieee80211_alloc_hw()
2060 int ieee80211_register_hw(struct ieee80211_hw *hw);
2063 * struct ieee80211_tpt_blink - throughput blink description
2064 * @throughput: throughput in Kbit/sec
2065 * @blink_time: blink time in milliseconds
2066 * (full cycle, ie. one off + one on period)
2068 struct ieee80211_tpt_blink {
2074 * enum ieee80211_tpt_led_trigger_flags - throughput trigger flags
2075 * @IEEE80211_TPT_LEDTRIG_FL_RADIO: enable blinking with radio
2076 * @IEEE80211_TPT_LEDTRIG_FL_WORK: enable blinking when working
2077 * @IEEE80211_TPT_LEDTRIG_FL_CONNECTED: enable blinking when at least one
2078 * interface is connected in some way, including being an AP
2080 enum ieee80211_tpt_led_trigger_flags {
2081 IEEE80211_TPT_LEDTRIG_FL_RADIO = BIT(0),
2082 IEEE80211_TPT_LEDTRIG_FL_WORK = BIT(1),
2083 IEEE80211_TPT_LEDTRIG_FL_CONNECTED = BIT(2),
2086 #ifdef CONFIG_MAC80211_LEDS
2087 extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
2088 extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
2089 extern char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw);
2090 extern char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw);
2091 extern char *__ieee80211_create_tpt_led_trigger(
2092 struct ieee80211_hw *hw, unsigned int flags,
2093 const struct ieee80211_tpt_blink *blink_table,
2094 unsigned int blink_table_len);
2097 * ieee80211_get_tx_led_name - get name of TX LED
2099 * mac80211 creates a transmit LED trigger for each wireless hardware
2100 * that can be used to drive LEDs if your driver registers a LED device.
2101 * This function returns the name (or %NULL if not configured for LEDs)
2102 * of the trigger so you can automatically link the LED device.
2104 * @hw: the hardware to get the LED trigger name for
2106 static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw)
2108 #ifdef CONFIG_MAC80211_LEDS
2109 return __ieee80211_get_tx_led_name(hw);
2116 * ieee80211_get_rx_led_name - get name of RX LED
2118 * mac80211 creates a receive LED trigger for each wireless hardware
2119 * that can be used to drive LEDs if your driver registers a LED device.
2120 * This function returns the name (or %NULL if not configured for LEDs)
2121 * of the trigger so you can automatically link the LED device.
2123 * @hw: the hardware to get the LED trigger name for
2125 static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw)
2127 #ifdef CONFIG_MAC80211_LEDS
2128 return __ieee80211_get_rx_led_name(hw);
2135 * ieee80211_get_assoc_led_name - get name of association LED
2137 * mac80211 creates a association LED trigger for each wireless hardware
2138 * that can be used to drive LEDs if your driver registers a LED device.
2139 * This function returns the name (or %NULL if not configured for LEDs)
2140 * of the trigger so you can automatically link the LED device.
2142 * @hw: the hardware to get the LED trigger name for
2144 static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw)
2146 #ifdef CONFIG_MAC80211_LEDS
2147 return __ieee80211_get_assoc_led_name(hw);
2154 * ieee80211_get_radio_led_name - get name of radio LED
2156 * mac80211 creates a radio change LED trigger for each wireless hardware
2157 * that can be used to drive LEDs if your driver registers a LED device.
2158 * This function returns the name (or %NULL if not configured for LEDs)
2159 * of the trigger so you can automatically link the LED device.
2161 * @hw: the hardware to get the LED trigger name for
2163 static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw)
2165 #ifdef CONFIG_MAC80211_LEDS
2166 return __ieee80211_get_radio_led_name(hw);
2173 * ieee80211_create_tpt_led_trigger - create throughput LED trigger
2174 * @hw: the hardware to create the trigger for
2175 * @flags: trigger flags, see &enum ieee80211_tpt_led_trigger_flags
2176 * @blink_table: the blink table -- needs to be ordered by throughput
2177 * @blink_table_len: size of the blink table
2179 * This function returns %NULL (in case of error, or if no LED
2180 * triggers are configured) or the name of the new trigger.
2181 * This function must be called before ieee80211_register_hw().
2183 static inline char *
2184 ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, unsigned int flags,
2185 const struct ieee80211_tpt_blink *blink_table,
2186 unsigned int blink_table_len)
2188 #ifdef CONFIG_MAC80211_LEDS
2189 return __ieee80211_create_tpt_led_trigger(hw, flags, blink_table,
2197 * ieee80211_unregister_hw - Unregister a hardware device
2199 * This function instructs mac80211 to free allocated resources
2200 * and unregister netdevices from the networking subsystem.
2202 * @hw: the hardware to unregister
2204 void ieee80211_unregister_hw(struct ieee80211_hw *hw);
2207 * ieee80211_free_hw - free hardware descriptor
2209 * This function frees everything that was allocated, including the
2210 * private data for the driver. You must call ieee80211_unregister_hw()
2211 * before calling this function.
2213 * @hw: the hardware to free
2215 void ieee80211_free_hw(struct ieee80211_hw *hw);
2218 * ieee80211_restart_hw - restart hardware completely
2220 * Call this function when the hardware was restarted for some reason
2221 * (hardware error, ...) and the driver is unable to restore its state
2222 * by itself. mac80211 assumes that at this point the driver/hardware
2223 * is completely uninitialised and stopped, it starts the process by
2224 * calling the ->start() operation. The driver will need to reset all
2225 * internal state that it has prior to calling this function.
2227 * @hw: the hardware to restart
2229 void ieee80211_restart_hw(struct ieee80211_hw *hw);
2231 /** ieee80211_napi_schedule - schedule NAPI poll
2233 * Use this function to schedule NAPI polling on a device.
2235 * @hw: the hardware to start polling
2237 void ieee80211_napi_schedule(struct ieee80211_hw *hw);
2239 /** ieee80211_napi_complete - complete NAPI polling
2241 * Use this function to finish NAPI polling on a device.
2243 * @hw: the hardware to stop polling
2245 void ieee80211_napi_complete(struct ieee80211_hw *hw);
2248 * ieee80211_rx - receive frame
2250 * Use this function to hand received frames to mac80211. The receive
2251 * buffer in @skb must start with an IEEE 802.11 header. In case of a
2252 * paged @skb is used, the driver is recommended to put the ieee80211
2253 * header of the frame on the linear part of the @skb to avoid memory
2254 * allocation and/or memcpy by the stack.
2256 * This function may not be called in IRQ context. Calls to this function
2257 * for a single hardware must be synchronized against each other. Calls to
2258 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
2259 * mixed for a single hardware.
2261 * In process context use instead ieee80211_rx_ni().
2263 * @hw: the hardware this frame came in on
2264 * @skb: the buffer to receive, owned by mac80211 after this call
2266 void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb);
2269 * ieee80211_rx_irqsafe - receive frame
2271 * Like ieee80211_rx() but can be called in IRQ context
2272 * (internally defers to a tasklet.)
2274 * Calls to this function, ieee80211_rx() or ieee80211_rx_ni() may not
2275 * be mixed for a single hardware.
2277 * @hw: the hardware this frame came in on
2278 * @skb: the buffer to receive, owned by mac80211 after this call
2280 void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb);
2283 * ieee80211_rx_ni - receive frame (in process context)
2285 * Like ieee80211_rx() but can be called in process context
2286 * (internally disables bottom halves).
2288 * Calls to this function, ieee80211_rx() and ieee80211_rx_irqsafe() may
2289 * not be mixed for a single hardware.
2291 * @hw: the hardware this frame came in on
2292 * @skb: the buffer to receive, owned by mac80211 after this call
2294 static inline void ieee80211_rx_ni(struct ieee80211_hw *hw,
2295 struct sk_buff *skb)
2298 ieee80211_rx(hw, skb);
2303 * ieee80211_sta_ps_transition - PS transition for connected sta
2305 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS
2306 * flag set, use this function to inform mac80211 about a connected station
2307 * entering/leaving PS mode.
2309 * This function may not be called in IRQ context or with softirqs enabled.
2311 * Calls to this function for a single hardware must be synchronized against
2314 * The function returns -EINVAL when the requested PS mode is already set.
2316 * @sta: currently connected sta
2317 * @start: start or stop PS
2319 int ieee80211_sta_ps_transition(struct ieee80211_sta *sta, bool start);
2322 * ieee80211_sta_ps_transition_ni - PS transition for connected sta
2323 * (in process context)
2325 * Like ieee80211_sta_ps_transition() but can be called in process context
2326 * (internally disables bottom halves). Concurrent call restriction still
2329 * @sta: currently connected sta
2330 * @start: start or stop PS
2332 static inline int ieee80211_sta_ps_transition_ni(struct ieee80211_sta *sta,
2338 ret = ieee80211_sta_ps_transition(sta, start);
2345 * The TX headroom reserved by mac80211 for its own tx_status functions.
2346 * This is enough for the radiotap header.
2348 #define IEEE80211_TX_STATUS_HEADROOM 13
2351 * ieee80211_sta_set_tim - set the TIM bit for a sleeping station
2352 * @sta: &struct ieee80211_sta pointer for the sleeping station
2354 * If a driver buffers frames for a powersave station instead of passing
2355 * them back to mac80211 for retransmission, the station needs to be told
2356 * to wake up using the TIM bitmap in the beacon.
2358 * This function sets the station's TIM bit - it will be cleared when the
2361 void ieee80211_sta_set_tim(struct ieee80211_sta *sta);
2364 * ieee80211_tx_status - transmit status callback
2366 * Call this function for all transmitted frames after they have been
2367 * transmitted. It is permissible to not call this function for
2368 * multicast frames but this can affect statistics.
2370 * This function may not be called in IRQ context. Calls to this function
2371 * for a single hardware must be synchronized against each other. Calls
2372 * to this function, ieee80211_tx_status_ni() and ieee80211_tx_status_irqsafe()
2373 * may not be mixed for a single hardware.
2375 * @hw: the hardware the frame was transmitted by
2376 * @skb: the frame that was transmitted, owned by mac80211 after this call
2378 void ieee80211_tx_status(struct ieee80211_hw *hw,
2379 struct sk_buff *skb);
2382 * ieee80211_tx_status_ni - transmit status callback (in process context)
2384 * Like ieee80211_tx_status() but can be called in process context.
2386 * Calls to this function, ieee80211_tx_status() and
2387 * ieee80211_tx_status_irqsafe() may not be mixed
2388 * for a single hardware.
2390 * @hw: the hardware the frame was transmitted by
2391 * @skb: the frame that was transmitted, owned by mac80211 after this call
2393 static inline void ieee80211_tx_status_ni(struct ieee80211_hw *hw,
2394 struct sk_buff *skb)
2397 ieee80211_tx_status(hw, skb);
2402 * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback
2404 * Like ieee80211_tx_status() but can be called in IRQ context
2405 * (internally defers to a tasklet.)
2407 * Calls to this function, ieee80211_tx_status() and
2408 * ieee80211_tx_status_ni() may not be mixed for a single hardware.
2410 * @hw: the hardware the frame was transmitted by
2411 * @skb: the frame that was transmitted, owned by mac80211 after this call
2413 void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
2414 struct sk_buff *skb);
2417 * ieee80211_report_low_ack - report non-responding station
2419 * When operating in AP-mode, call this function to report a non-responding
2422 * @sta: the non-responding connected sta
2423 * @num_packets: number of packets sent to @sta without a response
2425 void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets);
2428 * ieee80211_beacon_get_tim - beacon generation function
2429 * @hw: pointer obtained from ieee80211_alloc_hw().
2430 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
2431 * @tim_offset: pointer to variable that will receive the TIM IE offset.
2432 * Set to 0 if invalid (in non-AP modes).
2433 * @tim_length: pointer to variable that will receive the TIM IE length,
2434 * (including the ID and length bytes!).
2435 * Set to 0 if invalid (in non-AP modes).
2437 * If the driver implements beaconing modes, it must use this function to
2438 * obtain the beacon frame/template.
2440 * If the beacon frames are generated by the host system (i.e., not in
2441 * hardware/firmware), the driver uses this function to get each beacon
2442 * frame from mac80211 -- it is responsible for calling this function
2443 * before the beacon is needed (e.g. based on hardware interrupt).
2445 * If the beacon frames are generated by the device, then the driver
2446 * must use the returned beacon as the template and change the TIM IE
2447 * according to the current DTIM parameters/TIM bitmap.
2449 * The driver is responsible for freeing the returned skb.
2451 struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw,
2452 struct ieee80211_vif *vif,
2453 u16 *tim_offset, u16 *tim_length);
2456 * ieee80211_beacon_get - beacon generation function
2457 * @hw: pointer obtained from ieee80211_alloc_hw().
2458 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
2460 * See ieee80211_beacon_get_tim().
2462 static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
2463 struct ieee80211_vif *vif)
2465 return ieee80211_beacon_get_tim(hw, vif, NULL, NULL);
2469 * ieee80211_pspoll_get - retrieve a PS Poll template
2470 * @hw: pointer obtained from ieee80211_alloc_hw().
2471 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
2473 * Creates a PS Poll a template which can, for example, uploaded to
2474 * hardware. The template must be updated after association so that correct
2475 * AID, BSSID and MAC address is used.
2477 * Note: Caller (or hardware) is responsible for setting the
2478 * &IEEE80211_FCTL_PM bit.
2480 struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw,
2481 struct ieee80211_vif *vif);
2484 * ieee80211_nullfunc_get - retrieve a nullfunc template
2485 * @hw: pointer obtained from ieee80211_alloc_hw().
2486 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
2488 * Creates a Nullfunc template which can, for example, uploaded to
2489 * hardware. The template must be updated after association so that correct
2490 * BSSID and address is used.
2492 * Note: Caller (or hardware) is responsible for setting the
2493 * &IEEE80211_FCTL_PM bit as well as Duration and Sequence Control fields.
2495 struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw,
2496 struct ieee80211_vif *vif);
2499 * ieee80211_probereq_get - retrieve a Probe Request template
2500 * @hw: pointer obtained from ieee80211_alloc_hw().
2501 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
2502 * @ssid: SSID buffer
2503 * @ssid_len: length of SSID
2504 * @ie: buffer containing all IEs except SSID for the template
2505 * @ie_len: length of the IE buffer
2507 * Creates a Probe Request template which can, for example, be uploaded to
2510 struct sk_buff *ieee80211_probereq_get(struct ieee80211_hw *hw,
2511 struct ieee80211_vif *vif,
2512 const u8 *ssid, size_t ssid_len,
2513 const u8 *ie, size_t ie_len);
2516 * ieee80211_rts_get - RTS frame generation function
2517 * @hw: pointer obtained from ieee80211_alloc_hw().
2518 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
2519 * @frame: pointer to the frame that is going to be protected by the RTS.
2520 * @frame_len: the frame length (in octets).
2521 * @frame_txctl: &struct ieee80211_tx_info of the frame.
2522 * @rts: The buffer where to store the RTS frame.
2524 * If the RTS frames are generated by the host system (i.e., not in
2525 * hardware/firmware), the low-level driver uses this function to receive
2526 * the next RTS frame from the 802.11 code. The low-level is responsible
2527 * for calling this function before and RTS frame is needed.
2529 void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
2530 const void *frame, size_t frame_len,
2531 const struct ieee80211_tx_info *frame_txctl,
2532 struct ieee80211_rts *rts);
2535 * ieee80211_rts_duration - Get the duration field for an RTS frame
2536 * @hw: pointer obtained from ieee80211_alloc_hw().
2537 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
2538 * @frame_len: the length of the frame that is going to be protected by the RTS.
2539 * @frame_txctl: &struct ieee80211_tx_info of the frame.
2541 * If the RTS is generated in firmware, but the host system must provide
2542 * the duration field, the low-level driver uses this function to receive
2543 * the duration field value in little-endian byteorder.
2545 __le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
2546 struct ieee80211_vif *vif, size_t frame_len,
2547 const struct ieee80211_tx_info *frame_txctl);
2550 * ieee80211_ctstoself_get - CTS-to-self frame generation function
2551 * @hw: pointer obtained from ieee80211_alloc_hw().
2552 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
2553 * @frame: pointer to the frame that is going to be protected by the CTS-to-self.
2554 * @frame_len: the frame length (in octets).
2555 * @frame_txctl: &struct ieee80211_tx_info of the frame.
2556 * @cts: The buffer where to store the CTS-to-self frame.
2558 * If the CTS-to-self frames are generated by the host system (i.e., not in
2559 * hardware/firmware), the low-level driver uses this function to receive
2560 * the next CTS-to-self frame from the 802.11 code. The low-level is responsible
2561 * for calling this function before and CTS-to-self frame is needed.
2563 void ieee80211_ctstoself_get(struct ieee80211_hw *hw,
2564 struct ieee80211_vif *vif,
2565 const void *frame, size_t frame_len,
2566 const struct ieee80211_tx_info *frame_txctl,
2567 struct ieee80211_cts *cts);
2570 * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame
2571 * @hw: pointer obtained from ieee80211_alloc_hw().
2572 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
2573 * @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
2574 * @frame_txctl: &struct ieee80211_tx_info of the frame.
2576 * If the CTS-to-self is generated in firmware, but the host system must provide
2577 * the duration field, the low-level driver uses this function to receive
2578 * the duration field value in little-endian byteorder.
2580 __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
2581 struct ieee80211_vif *vif,
2583 const struct ieee80211_tx_info *frame_txctl);
2586 * ieee80211_generic_frame_duration - Calculate the duration field for a frame
2587 * @hw: pointer obtained from ieee80211_alloc_hw().
2588 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
2589 * @frame_len: the length of the frame.
2590 * @rate: the rate at which the frame is going to be transmitted.
2592 * Calculate the duration field of some generic frame, given its
2593 * length and transmission rate (in 100kbps).
2595 __le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
2596 struct ieee80211_vif *vif,
2598 struct ieee80211_rate *rate);
2601 * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
2602 * @hw: pointer as obtained from ieee80211_alloc_hw().
2603 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
2605 * Function for accessing buffered broadcast and multicast frames. If
2606 * hardware/firmware does not implement buffering of broadcast/multicast
2607 * frames when power saving is used, 802.11 code buffers them in the host
2608 * memory. The low-level driver uses this function to fetch next buffered
2609 * frame. In most cases, this is used when generating beacon frame. This
2610 * function returns a pointer to the next buffered skb or NULL if no more
2611 * buffered frames are available.
2613 * Note: buffered frames are returned only after DTIM beacon frame was
2614 * generated with ieee80211_beacon_get() and the low-level driver must thus
2615 * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns
2616 * NULL if the previous generated beacon was not DTIM, so the low-level driver
2617 * does not need to check for DTIM beacons separately and should be able to
2618 * use common code for all beacons.
2621 ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
2624 * ieee80211_get_tkip_p1k_iv - get a TKIP phase 1 key for IV32
2626 * This function returns the TKIP phase 1 key for the given IV32.
2628 * @keyconf: the parameter passed with the set key
2629 * @iv32: IV32 to get the P1K for
2630 * @p1k: a buffer to which the key will be written, as 5 u16 values
2632 void ieee80211_get_tkip_p1k_iv(struct ieee80211_key_conf *keyconf,
2633 u32 iv32, u16 *p1k);
2636 * ieee80211_get_tkip_p1k - get a TKIP phase 1 key
2638 * This function returns the TKIP phase 1 key for the IV32 taken
2639 * from the given packet.
2641 * @keyconf: the parameter passed with the set key
2642 * @skb: the packet to take the IV32 value from that will be encrypted
2644 * @p1k: a buffer to which the key will be written, as 5 u16 values
2646 static inline void ieee80211_get_tkip_p1k(struct ieee80211_key_conf *keyconf,
2647 struct sk_buff *skb, u16 *p1k)
2649 struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
2650 const u8 *data = (u8 *)hdr + ieee80211_hdrlen(hdr->frame_control);
2651 u32 iv32 = get_unaligned_le32(&data[4]);
2653 ieee80211_get_tkip_p1k_iv(keyconf, iv32, p1k);
2657 * ieee80211_get_tkip_rx_p1k - get a TKIP phase 1 key for RX
2659 * This function returns the TKIP phase 1 key for the given IV32
2660 * and transmitter address.
2662 * @keyconf: the parameter passed with the set key
2663 * @ta: TA that will be used with the key
2664 * @iv32: IV32 to get the P1K for
2665 * @p1k: a buffer to which the key will be written, as 5 u16 values
2667 void ieee80211_get_tkip_rx_p1k(struct ieee80211_key_conf *keyconf,
2668 const u8 *ta, u32 iv32, u16 *p1k);
2671 * ieee80211_get_tkip_p2k - get a TKIP phase 2 key
2673 * This function computes the TKIP RC4 key for the IV values
2676 * @keyconf: the parameter passed with the set key
2677 * @skb: the packet to take the IV32/IV16 values from that will be
2678 * encrypted with this key
2679 * @p2k: a buffer to which the key will be written, 16 bytes
2681 void ieee80211_get_tkip_p2k(struct ieee80211_key_conf *keyconf,
2682 struct sk_buff *skb, u8 *p2k);
2685 * struct ieee80211_key_seq - key sequence counter
2687 * @tkip: TKIP data, containing IV32 and IV16 in host byte order
2688 * @ccmp: PN data, most significant byte first (big endian,
2689 * reverse order than in packet)
2690 * @aes_cmac: PN data, most significant byte first (big endian,
2691 * reverse order than in packet)
2693 struct ieee80211_key_seq {
2709 * ieee80211_get_key_tx_seq - get key TX sequence counter
2711 * @keyconf: the parameter passed with the set key
2712 * @seq: buffer to receive the sequence data
2714 * This function allows a driver to retrieve the current TX IV/PN
2715 * for the given key. It must not be called if IV generation is
2716 * offloaded to the device.
2718 * Note that this function may only be called when no TX processing
2719 * can be done concurrently, for example when queues are stopped
2720 * and the stop has been synchronized.
2722 void ieee80211_get_key_tx_seq(struct ieee80211_key_conf *keyconf,
2723 struct ieee80211_key_seq *seq);
2726 * ieee80211_get_key_rx_seq - get key RX sequence counter
2728 * @keyconf: the parameter passed with the set key
2729 * @tid: The TID, or -1 for the management frame value (CCMP only);
2730 * the value on TID 0 is also used for non-QoS frames. For
2731 * CMAC, only TID 0 is valid.
2732 * @seq: buffer to receive the sequence data
2734 * This function allows a driver to retrieve the current RX IV/PNs
2735 * for the given key. It must not be called if IV checking is done
2736 * by the device and not by mac80211.
2738 * Note that this function may only be called when no RX processing
2739 * can be done concurrently.
2741 void ieee80211_get_key_rx_seq(struct ieee80211_key_conf *keyconf,
2742 int tid, struct ieee80211_key_seq *seq);
2745 * ieee80211_gtk_rekey_notify - notify userspace supplicant of rekeying
2746 * @vif: virtual interface the rekeying was done on
2747 * @bssid: The BSSID of the AP, for checking association
2748 * @replay_ctr: the new replay counter after GTK rekeying
2749 * @gfp: allocation flags
2751 void ieee80211_gtk_rekey_notify(struct ieee80211_vif *vif, const u8 *bssid,
2752 const u8 *replay_ctr, gfp_t gfp);
2755 * ieee80211_wake_queue - wake specific queue
2756 * @hw: pointer as obtained from ieee80211_alloc_hw().
2757 * @queue: queue number (counted from zero).
2759 * Drivers should use this function instead of netif_wake_queue.
2761 void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue);
2764 * ieee80211_stop_queue - stop specific queue
2765 * @hw: pointer as obtained from ieee80211_alloc_hw().
2766 * @queue: queue number (counted from zero).
2768 * Drivers should use this function instead of netif_stop_queue.
2770 void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue);
2773 * ieee80211_queue_stopped - test status of the queue
2774 * @hw: pointer as obtained from ieee80211_alloc_hw().
2775 * @queue: queue number (counted from zero).
2777 * Drivers should use this function instead of netif_stop_queue.
2780 int ieee80211_queue_stopped(struct ieee80211_hw *hw, int queue);
2783 * ieee80211_stop_queues - stop all queues
2784 * @hw: pointer as obtained from ieee80211_alloc_hw().
2786 * Drivers should use this function instead of netif_stop_queue.
2788 void ieee80211_stop_queues(struct ieee80211_hw *hw);
2791 * ieee80211_wake_queues - wake all queues
2792 * @hw: pointer as obtained from ieee80211_alloc_hw().
2794 * Drivers should use this function instead of netif_wake_queue.
2796 void ieee80211_wake_queues(struct ieee80211_hw *hw);
2799 * ieee80211_scan_completed - completed hardware scan
2801 * When hardware scan offload is used (i.e. the hw_scan() callback is
2802 * assigned) this function needs to be called by the driver to notify
2803 * mac80211 that the scan finished. This function can be called from
2804 * any context, including hardirq context.
2806 * @hw: the hardware that finished the scan
2807 * @aborted: set to true if scan was aborted
2809 void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted);
2812 * ieee80211_sched_scan_results - got results from scheduled scan
2814 * When a scheduled scan is running, this function needs to be called by the
2815 * driver whenever there are new scan results available.
2817 * @hw: the hardware that is performing scheduled scans
2819 void ieee80211_sched_scan_results(struct ieee80211_hw *hw);
2822 * ieee80211_sched_scan_stopped - inform that the scheduled scan has stopped
2824 * When a scheduled scan is running, this function can be called by
2825 * the driver if it needs to stop the scan to perform another task.
2826 * Usual scenarios are drivers that cannot continue the scheduled scan
2827 * while associating, for instance.
2829 * @hw: the hardware that is performing scheduled scans
2831 void ieee80211_sched_scan_stopped(struct ieee80211_hw *hw);
2834 * ieee80211_iterate_active_interfaces - iterate active interfaces
2836 * This function iterates over the interfaces associated with a given
2837 * hardware that are currently active and calls the callback for them.
2838 * This function allows the iterator function to sleep, when the iterator
2839 * function is atomic @ieee80211_iterate_active_interfaces_atomic can
2841 * Does not iterate over a new interface during add_interface()
2843 * @hw: the hardware struct of which the interfaces should be iterated over
2844 * @iterator: the iterator function to call
2845 * @data: first argument of the iterator function
2847 void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw,
2848 void (*iterator)(void *data, u8 *mac,
2849 struct ieee80211_vif *vif),
2853 * ieee80211_iterate_active_interfaces_atomic - iterate active interfaces
2855 * This function iterates over the interfaces associated with a given
2856 * hardware that are currently active and calls the callback for them.
2857 * This function requires the iterator callback function to be atomic,
2858 * if that is not desired, use @ieee80211_iterate_active_interfaces instead.
2859 * Does not iterate over a new interface during add_interface()
2861 * @hw: the hardware struct of which the interfaces should be iterated over
2862 * @iterator: the iterator function to call, cannot sleep
2863 * @data: first argument of the iterator function
2865 void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw,
2866 void (*iterator)(void *data,
2868 struct ieee80211_vif *vif),
2872 * ieee80211_queue_work - add work onto the mac80211 workqueue
2874 * Drivers and mac80211 use this to add work onto the mac80211 workqueue.
2875 * This helper ensures drivers are not queueing work when they should not be.
2877 * @hw: the hardware struct for the interface we are adding work for
2878 * @work: the work we want to add onto the mac80211 workqueue
2880 void ieee80211_queue_work(struct ieee80211_hw *hw, struct work_struct *work);
2883 * ieee80211_queue_delayed_work - add work onto the mac80211 workqueue
2885 * Drivers and mac80211 use this to queue delayed work onto the mac80211
2888 * @hw: the hardware struct for the interface we are adding work for
2889 * @dwork: delayable work to queue onto the mac80211 workqueue
2890 * @delay: number of jiffies to wait before queueing
2892 void ieee80211_queue_delayed_work(struct ieee80211_hw *hw,
2893 struct delayed_work *dwork,
2894 unsigned long delay);
2897 * ieee80211_start_tx_ba_session - Start a tx Block Ack session.
2898 * @sta: the station for which to start a BA session
2899 * @tid: the TID to BA on.
2900 * @timeout: session timeout value (in TUs)
2902 * Return: success if addBA request was sent, failure otherwise
2904 * Although mac80211/low level driver/user space application can estimate
2905 * the need to start aggregation on a certain RA/TID, the session level
2906 * will be managed by the mac80211.
2908 int ieee80211_start_tx_ba_session(struct ieee80211_sta *sta, u16 tid,
2912 * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate.
2913 * @vif: &struct ieee80211_vif pointer from the add_interface callback
2914 * @ra: receiver address of the BA session recipient.
2915 * @tid: the TID to BA on.
2917 * This function must be called by low level driver once it has
2918 * finished with preparations for the BA session. It can be called
2921 void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
2925 * ieee80211_stop_tx_ba_session - Stop a Block Ack session.
2926 * @sta: the station whose BA session to stop
2927 * @tid: the TID to stop BA.
2929 * Return: negative error if the TID is invalid, or no aggregation active
2931 * Although mac80211/low level driver/user space application can estimate
2932 * the need to stop aggregation on a certain RA/TID, the session level
2933 * will be managed by the mac80211.
2935 int ieee80211_stop_tx_ba_session(struct ieee80211_sta *sta, u16 tid);
2938 * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate.
2939 * @vif: &struct ieee80211_vif pointer from the add_interface callback
2940 * @ra: receiver address of the BA session recipient.
2941 * @tid: the desired TID to BA on.
2943 * This function must be called by low level driver once it has
2944 * finished with preparations for the BA session tear down. It
2945 * can be called from any context.
2947 void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
2951 * ieee80211_find_sta - find a station
2953 * @vif: virtual interface to look for station on
2954 * @addr: station's address
2956 * This function must be called under RCU lock and the
2957 * resulting pointer is only valid under RCU lock as well.
2959 struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif,
2963 * ieee80211_find_sta_by_ifaddr - find a station on hardware
2965 * @hw: pointer as obtained from ieee80211_alloc_hw()
2966 * @addr: remote station's address
2967 * @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'.
2969 * This function must be called under RCU lock and the
2970 * resulting pointer is only valid under RCU lock as well.
2972 * NOTE: You may pass NULL for localaddr, but then you will just get
2973 * the first STA that matches the remote address 'addr'.
2974 * We can have multiple STA associated with multiple
2975 * logical stations (e.g. consider a station connecting to another
2976 * BSSID on the same AP hardware without disconnecting first).
2977 * In this case, the result of this method with localaddr NULL
2980 * DO NOT USE THIS FUNCTION with localaddr NULL if at all possible.
2982 struct ieee80211_sta *ieee80211_find_sta_by_ifaddr(struct ieee80211_hw *hw,
2984 const u8 *localaddr);
2987 * ieee80211_sta_block_awake - block station from waking up
2989 * @pubsta: the station
2990 * @block: whether to block or unblock
2992 * Some devices require that all frames that are on the queues
2993 * for a specific station that went to sleep are flushed before
2994 * a poll response or frames after the station woke up can be
2995 * delivered to that it. Note that such frames must be rejected
2996 * by the driver as filtered, with the appropriate status flag.
2998 * This function allows implementing this mode in a race-free
3001 * To do this, a driver must keep track of the number of frames
3002 * still enqueued for a specific station. If this number is not
3003 * zero when the station goes to sleep, the driver must call
3004 * this function to force mac80211 to consider the station to
3005 * be asleep regardless of the station's actual state. Once the
3006 * number of outstanding frames reaches zero, the driver must
3007 * call this function again to unblock the station. That will
3008 * cause mac80211 to be able to send ps-poll responses, and if
3009 * the station queried in the meantime then frames will also
3010 * be sent out as a result of this. Additionally, the driver
3011 * will be notified that the station woke up some time after
3012 * it is unblocked, regardless of whether the station actually
3013 * woke up while blocked or not.
3015 void ieee80211_sta_block_awake(struct ieee80211_hw *hw,
3016 struct ieee80211_sta *pubsta, bool block);
3019 * ieee80211_iter_keys - iterate keys programmed into the device
3020 * @hw: pointer obtained from ieee80211_alloc_hw()
3021 * @vif: virtual interface to iterate, may be %NULL for all
3022 * @iter: iterator function that will be called for each key
3023 * @iter_data: custom data to pass to the iterator function
3025 * This function can be used to iterate all the keys known to
3026 * mac80211, even those that weren't previously programmed into
3027 * the device. This is intended for use in WoWLAN if the device
3028 * needs reprogramming of the keys during suspend. Note that due
3029 * to locking reasons, it is also only safe to call this at few
3030 * spots since it must hold the RTNL and be able to sleep.
3032 * The order in which the keys are iterated matches the order
3033 * in which they were originally installed and handed to the
3036 void ieee80211_iter_keys(struct ieee80211_hw *hw,
3037 struct ieee80211_vif *vif,
3038 void (*iter)(struct ieee80211_hw *hw,
3039 struct ieee80211_vif *vif,
3040 struct ieee80211_sta *sta,
3041 struct ieee80211_key_conf *key,
3046 * ieee80211_ap_probereq_get - retrieve a Probe Request template
3047 * @hw: pointer obtained from ieee80211_alloc_hw().
3048 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3050 * Creates a Probe Request template which can, for example, be uploaded to
3051 * hardware. The template is filled with bssid, ssid and supported rate
3052 * information. This function must only be called from within the
3053 * .bss_info_changed callback function and only in managed mode. The function
3054 * is only useful when the interface is associated, otherwise it will return
3057 struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw,
3058 struct ieee80211_vif *vif);
3061 * ieee80211_beacon_loss - inform hardware does not receive beacons
3063 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3065 * When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTER and
3066 * %IEEE80211_CONF_PS is set, the driver needs to inform whenever the
3067 * hardware is not receiving beacons with this function.
3069 void ieee80211_beacon_loss(struct ieee80211_vif *vif);
3072 * ieee80211_connection_loss - inform hardware has lost connection to the AP
3074 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3076 * When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTER, and
3077 * %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver
3078 * needs to inform if the connection to the AP has been lost.
3080 * This function will cause immediate change to disassociated state,
3081 * without connection recovery attempts.
3083 void ieee80211_connection_loss(struct ieee80211_vif *vif);
3086 * ieee80211_resume_disconnect - disconnect from AP after resume
3088 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3090 * Instructs mac80211 to disconnect from the AP after resume.
3091 * Drivers can use this after WoWLAN if they know that the
3092 * connection cannot be kept up, for example because keys were
3093 * used while the device was asleep but the replay counters or
3094 * similar cannot be retrieved from the device during resume.
3096 * Note that due to implementation issues, if the driver uses
3097 * the reconfiguration functionality during resume the interface
3098 * will still be added as associated first during resume and then
3099 * disconnect normally later.
3101 * This function can only be called from the resume callback and
3102 * the driver must not be holding any of its own locks while it
3103 * calls this function, or at least not any locks it needs in the
3104 * key configuration paths (if it supports HW crypto).
3106 void ieee80211_resume_disconnect(struct ieee80211_vif *vif);
3109 * ieee80211_disable_dyn_ps - force mac80211 to temporarily disable dynamic psm
3111 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3113 * Some hardware require full power save to manage simultaneous BT traffic
3114 * on the WLAN frequency. Full PSM is required periodically, whenever there are
3115 * burst of BT traffic. The hardware gets information of BT traffic via
3116 * hardware co-existence lines, and consequentially requests mac80211 to
3117 * (temporarily) enter full psm.
3118 * This function will only temporarily disable dynamic PS, not enable PSM if
3119 * it was not already enabled.
3120 * The driver must make sure to re-enable dynamic PS using
3121 * ieee80211_enable_dyn_ps() if the driver has disabled it.
3124 void ieee80211_disable_dyn_ps(struct ieee80211_vif *vif);
3127 * ieee80211_enable_dyn_ps - restore dynamic psm after being disabled
3129 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3131 * This function restores dynamic PS after being temporarily disabled via
3132 * ieee80211_disable_dyn_ps(). Each ieee80211_disable_dyn_ps() call must
3133 * be coupled with an eventual call to this function.
3136 void ieee80211_enable_dyn_ps(struct ieee80211_vif *vif);
3139 * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring
3140 * rssi threshold triggered
3142 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3143 * @rssi_event: the RSSI trigger event type
3144 * @gfp: context flags
3146 * When the %IEEE80211_HW_SUPPORTS_CQM_RSSI is set, and a connection quality
3147 * monitoring is configured with an rssi threshold, the driver will inform
3148 * whenever the rssi level reaches the threshold.
3150 void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif,
3151 enum nl80211_cqm_rssi_threshold_event rssi_event,
3155 * ieee80211_get_operstate - get the operstate of the vif
3157 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3159 * The driver might need to know the operstate of the net_device
3160 * (specifically, whether the link is IF_OPER_UP after resume)
3162 unsigned char ieee80211_get_operstate(struct ieee80211_vif *vif);
3165 * ieee80211_chswitch_done - Complete channel switch process
3166 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3167 * @success: make the channel switch successful or not
3169 * Complete the channel switch post-process: set the new operational channel
3170 * and wake up the suspended queues.
3172 void ieee80211_chswitch_done(struct ieee80211_vif *vif, bool success);
3175 * ieee80211_request_smps - request SM PS transition
3176 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3177 * @smps_mode: new SM PS mode
3179 * This allows the driver to request an SM PS transition in managed
3180 * mode. This is useful when the driver has more information than
3181 * the stack about possible interference, for example by bluetooth.
3183 void ieee80211_request_smps(struct ieee80211_vif *vif,
3184 enum ieee80211_smps_mode smps_mode);
3187 * ieee80211_key_removed - disable hw acceleration for key
3188 * @key_conf: The key hw acceleration should be disabled for
3190 * This allows drivers to indicate that the given key has been
3191 * removed from hardware acceleration, due to a new key that
3192 * was added. Don't use this if the key can continue to be used
3193 * for TX, if the key restriction is on RX only it is permitted
3194 * to keep the key for TX only and not call this function.
3196 * Due to locking constraints, it may only be called during
3197 * @set_key. This function must be allowed to sleep, and the
3198 * key it tries to disable may still be used until it returns.
3200 void ieee80211_key_removed(struct ieee80211_key_conf *key_conf);
3203 * ieee80211_ready_on_channel - notification of remain-on-channel start
3204 * @hw: pointer as obtained from ieee80211_alloc_hw()
3206 void ieee80211_ready_on_channel(struct ieee80211_hw *hw);
3209 * ieee80211_remain_on_channel_expired - remain_on_channel duration expired
3210 * @hw: pointer as obtained from ieee80211_alloc_hw()
3212 void ieee80211_remain_on_channel_expired(struct ieee80211_hw *hw);
3215 * ieee80211_stop_rx_ba_session - callback to stop existing BA sessions
3217 * in order not to harm the system performance and user experience, the device
3218 * may request not to allow any rx ba session and tear down existing rx ba
3219 * sessions based on system constraints such as periodic BT activity that needs
3220 * to limit wlan activity (eg.sco or a2dp)."
3221 * in such cases, the intention is to limit the duration of the rx ppdu and
3222 * therefore prevent the peer device to use a-mpdu aggregation.
3224 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3225 * @ba_rx_bitmap: Bit map of open rx ba per tid
3226 * @addr: & to bssid mac address
3228 void ieee80211_stop_rx_ba_session(struct ieee80211_vif *vif, u16 ba_rx_bitmap,
3231 /* Rate control API */
3234 * enum rate_control_changed - flags to indicate which parameter changed
3236 * @IEEE80211_RC_HT_CHANGED: The HT parameters of the operating channel have
3237 * changed, rate control algorithm can update its internal state if needed.
3239 enum rate_control_changed {
3240 IEEE80211_RC_HT_CHANGED = BIT(0)
3244 * struct ieee80211_tx_rate_control - rate control information for/from RC algo
3246 * @hw: The hardware the algorithm is invoked for.
3247 * @sband: The band this frame is being transmitted on.
3248 * @bss_conf: the current BSS configuration
3249 * @reported_rate: The rate control algorithm can fill this in to indicate
3250 * which rate should be reported to userspace as the current rate and
3251 * used for rate calculations in the mesh network.
3252 * @rts: whether RTS will be used for this frame because it is longer than the
3254 * @short_preamble: whether mac80211 will request short-preamble transmission
3255 * if the selected rate supports it
3256 * @max_rate_idx: user-requested maximum rate (not MCS for now)
3257 * (deprecated; this will be removed once drivers get updated to use
3259 * @rate_idx_mask: user-requested rate mask (not MCS for now)
3260 * @skb: the skb that will be transmitted, the control information in it needs
3262 * @bss: whether this frame is sent out in AP or IBSS mode
3264 struct ieee80211_tx_rate_control {
3265 struct ieee80211_hw *hw;
3266 struct ieee80211_supported_band *sband;
3267 struct ieee80211_bss_conf *bss_conf;
3268 struct sk_buff *skb;
3269 struct ieee80211_tx_rate reported_rate;
3270 bool rts, short_preamble;
3276 struct rate_control_ops {
3277 struct module *module;
3279 void *(*alloc)(struct ieee80211_hw *hw, struct dentry *debugfsdir);
3280 void (*free)(void *priv);
3282 void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp);
3283 void (*rate_init)(void *priv, struct ieee80211_supported_band *sband,
3284 struct ieee80211_sta *sta, void *priv_sta);
3285 void (*rate_update)(void *priv, struct ieee80211_supported_band *sband,
3286 struct ieee80211_sta *sta,
3287 void *priv_sta, u32 changed,
3288 enum nl80211_channel_type oper_chan_type);
3289 void (*free_sta)(void *priv, struct ieee80211_sta *sta,
3292 void (*tx_status)(void *priv, struct ieee80211_supported_band *sband,
3293 struct ieee80211_sta *sta, void *priv_sta,
3294 struct sk_buff *skb);
3295 void (*get_rate)(void *priv, struct ieee80211_sta *sta, void *priv_sta,
3296 struct ieee80211_tx_rate_control *txrc);
3298 void (*add_sta_debugfs)(void *priv, void *priv_sta,
3299 struct dentry *dir);
3300 void (*remove_sta_debugfs)(void *priv, void *priv_sta);
3303 static inline int rate_supported(struct ieee80211_sta *sta,
3304 enum ieee80211_band band,
3307 return (sta == NULL || sta->supp_rates[band] & BIT(index));
3311 * rate_control_send_low - helper for drivers for management/no-ack frames
3313 * Rate control algorithms that agree to use the lowest rate to
3314 * send management frames and NO_ACK data with the respective hw
3315 * retries should use this in the beginning of their mac80211 get_rate
3316 * callback. If true is returned the rate control can simply return.
3317 * If false is returned we guarantee that sta and sta and priv_sta is
3320 * Rate control algorithms wishing to do more intelligent selection of
3321 * rate for multicast/broadcast frames may choose to not use this.
3323 * @sta: &struct ieee80211_sta pointer to the target destination. Note
3324 * that this may be null.
3325 * @priv_sta: private rate control structure. This may be null.
3326 * @txrc: rate control information we sholud populate for mac80211.
3328 bool rate_control_send_low(struct ieee80211_sta *sta,
3330 struct ieee80211_tx_rate_control *txrc);
3334 rate_lowest_index(struct ieee80211_supported_band *sband,
3335 struct ieee80211_sta *sta)
3339 for (i = 0; i < sband->n_bitrates; i++)
3340 if (rate_supported(sta, sband->band, i))
3343 /* warn when we cannot find a rate. */
3350 bool rate_usable_index_exists(struct ieee80211_supported_band *sband,
3351 struct ieee80211_sta *sta)
3355 for (i = 0; i < sband->n_bitrates; i++)
3356 if (rate_supported(sta, sband->band, i))
3361 int ieee80211_rate_control_register(struct rate_control_ops *ops);
3362 void ieee80211_rate_control_unregister(struct rate_control_ops *ops);
3365 conf_is_ht20(struct ieee80211_conf *conf)
3367 return conf->channel_type == NL80211_CHAN_HT20;
3371 conf_is_ht40_minus(struct ieee80211_conf *conf)
3373 return conf->channel_type == NL80211_CHAN_HT40MINUS;
3377 conf_is_ht40_plus(struct ieee80211_conf *conf)
3379 return conf->channel_type == NL80211_CHAN_HT40PLUS;
3383 conf_is_ht40(struct ieee80211_conf *conf)
3385 return conf_is_ht40_minus(conf) || conf_is_ht40_plus(conf);
3389 conf_is_ht(struct ieee80211_conf *conf)
3391 return conf->channel_type != NL80211_CHAN_NO_HT;
3394 static inline enum nl80211_iftype
3395 ieee80211_iftype_p2p(enum nl80211_iftype type, bool p2p)
3399 case NL80211_IFTYPE_STATION:
3400 return NL80211_IFTYPE_P2P_CLIENT;
3401 case NL80211_IFTYPE_AP:
3402 return NL80211_IFTYPE_P2P_GO;
3410 static inline enum nl80211_iftype
3411 ieee80211_vif_type_p2p(struct ieee80211_vif *vif)
3413 return ieee80211_iftype_p2p(vif->type, vif->p2p);
3416 void ieee80211_enable_rssi_reports(struct ieee80211_vif *vif,
3418 int rssi_max_thold);
3420 void ieee80211_disable_rssi_reports(struct ieee80211_vif *vif);
3421 #endif /* MAC80211_H */