5 #include <dt-bindings/input/input.h>
8 model = "BTHOMEHUBV5A - BT Home Hub 5A";
11 bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
15 led-boot = &power_green;
16 led-failsafe = &power_red;
17 led-running = &power_blue;
19 led-internet = &broadband_blue;
20 led-wifi = &wireless_blue;
24 reg = <0x0 0x8000000>;
30 compatible = "gen_nand", "lantiq,nand-xway";
33 reg = <0x1 0x0 0x2000000>;
37 nand-ecc-strength = <3>;
38 nand-ecc-step-size = <256>;
41 compatible = "fixed-partitions";
52 reg = <0xa0000 0x20000>;
57 reg = <0xc0000 0x40000>;
61 reg = <0x100000 0x7e80000>;
64 * last 512 KiB are for the bad block table, not writable
70 gpio: pinmux@E100B10 {
71 pinctrl-names = "default";
72 pinctrl-0 = <&state_default>;
74 state_default: pinmux {
76 lantiq,groups = "mdio";
77 lantiq,function = "mdio";
93 lantiq,open-drain = <0>;
97 lantiq,groups = "nand cle", "nand ale";
98 lantiq,function = "ebu";
100 lantiq,open-drain = <0>;
104 lantiq,groups = "nand cs1";
105 lantiq,function = "ebu";
106 lantiq,open-drain = <0>;
114 gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
119 compatible = "lantiq,phy-xrx200";
120 firmware1 = "lantiq/vr9_phy11g_a1x.bin"; /*VR9 1.1*/
121 firmware2 = "lantiq/vr9_phy11g_a2x.bin"; /*VR9 1.2*/
126 compatible = "gpio-keys-polled";
127 #address-cells = <1>;
129 poll-interval = <100>;
133 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
134 linux,code = <KEY_RESTART>;
139 gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
140 linux,code = <KEY_WPS_BUTTON>;
145 gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
146 linux,code = <KEY_POWER>;
151 compatible = "gpio-leds";
153 /* broadband-* is a single RGB led */
155 label = "bthomehubv5a:red:broadband";
156 gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
159 label = "bthomehubv5a:green:broadband";
160 gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
162 broadband_blue: broadband-blue {
163 label = "bthomehubv5a:blue:broadband";
164 gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
167 /* wireless-* is a single RGB led */
169 label = "bthomehubv5a:red:wireless";
170 gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
173 label = "bthomehubv5a:green:wireless";
174 gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
176 wireless_blue: wireless-blue {
177 label = "bthomehubv5a:blue:wireless";
178 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
181 /* power-* is a single RGB led */
182 power_red: power-red {
183 label = "bthomehubv5a:red:power";
184 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
186 power_green: power-green {
187 label = "bthomehubv5a:green:power";
188 gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
189 default-state = "keep";
191 power_blue: power-blue {
192 label = "bthomehubv5a:blue:power";
193 gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
198 gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
205 gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
208 compatible = "pci168c,002d";
209 reg = <0x7000 0 0 0 0>;
210 qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */
217 compatible = "lantiq,xrx200-pdi";
218 #address-cells = <1>;
224 compatible = "lantiq,xrx200-pdi-port";
227 phy-handle = <&phy0>;
230 compatible = "lantiq,xrx200-pdi-port";
233 phy-handle = <&phy1>;
236 compatible = "lantiq,xrx200-pdi-port";
239 phy-handle = <&phy11>;
242 compatible = "lantiq,xrx200-pdi-port";
245 phy-handle = <&phy13>;
250 compatible = "lantiq,xrx200-pdi";
251 #address-cells = <1>;
257 compatible = "lantiq,xrx200-pdi-port";
260 phy-handle = <&phy5>;
265 #address-cells = <1>;
267 compatible = "lantiq,xrx200-mdio";
269 phy0: ethernet-phy@0 {
271 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
273 phy1: ethernet-phy@1 {
275 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
277 phy5: ethernet-phy@5 {
279 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
281 phy11: ethernet-phy@11 {
283 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
285 phy13: ethernet-phy@13 {
287 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";