is selected automatically. Check
Documentation/kdump/kdump.txt for further details.
+ crashkernel_low=size[KMG]
+ [KNL, x86] parts under 4G.
+
crashkernel=range1:size1[,range2:size2,...][@offset]
[KNL] Same as above, but depends on the memory
in the running system. The syntax of range is
that the amount of memory usable for all allocations
is not too small.
+ movablemem_map=acpi
+ [KNL,X86,IA-64,PPC] This parameter is similar to
+ memmap except it specifies the memory map of
+ ZONE_MOVABLE.
+ This option inform the kernel to use Hot Pluggable bit
+ in flags from SRAT from ACPI BIOS to determine which
+ memory devices could be hotplugged. The corresponding
+ memory ranges will be set as ZONE_MOVABLE.
+ NOTE: Whatever node the kernel resides in will always
+ be un-hotpluggable.
+
+ movablemem_map=nn[KMG]@ss[KMG]
+ [KNL,X86,IA-64,PPC] This parameter is similar to
+ memmap except it specifies the memory map of
+ ZONE_MOVABLE.
+ If user specifies memory ranges, the info in SRAT will
+ be ingored. And it works like the following:
+ - If more ranges are all within one node, then from
+ lowest ss to the end of the node will be ZONE_MOVABLE.
+ - If a range is within a node, then from ss to the end
+ of the node will be ZONE_MOVABLE.
+ - If a range covers two or more nodes, then from ss to
+ the end of the 1st node will be ZONE_MOVABLE, and all
+ the rest nodes will only have ZONE_MOVABLE.
+ If memmap is specified at the same time, the
+ movablemem_map will be limited within the memmap
+ areas. If kernelcore or movablecore is also specified,
+ movablemem_map will have higher priority to be
+ satisfied. So the administrator should be careful that
+ the amount of movablemem_map areas are not too large.
+ Otherwise kernel won't have enough memory to start.
+ NOTE: We don't stop users specifying the node the
+ kernel resides in as hotpluggable so that this
+ option can be used as a workaround of firmware
+ bugs.
+
MTD_Partition= [MTD]
Format: <name>,<region-number>,<size>,<offset>
This sorting is done to get a device
order compatible with older (<= 2.4) kernels.
nobfsort Don't sort PCI devices into breadth-first order.
+ pcie_bus_tune_off Disable PCIe MPS (Max Payload Size)
+ tuning and use the BIOS-configured MPS defaults.
+ pcie_bus_safe Set every device's MPS to the largest value
+ supported by all devices below the root complex.
+ pcie_bus_perf Set device MPS to the largest allowable MPS
+ based on its parent bus. Also set MRRS (Max
+ Read Request Size) to the largest supported
+ value (no larger than the MPS that the device
+ or bus can support) for best performance.
+ pcie_bus_peer2peer Set every device's MPS to 128B, which
+ every device is guaranteed to support. This
+ configuration allows peer-to-peer DMA between
+ any pair of devices, possibly at the cost of
+ reduced performance. This also guarantees
+ that hot-added devices will work.
cbiosize=nn[KMG] The fixed amount of bus space which is
reserved for the CardBus bridge's IO window.
The default value is 256 bytes.
the default.
off: Turn ECRC off
on: Turn ECRC on.
+ hpiosize=nn[KMG] The fixed amount of bus space which is
+ reserved for hotplug bridge's IO window.
+ Default size is 256 bytes.
+ hpmemsize=nn[KMG] The fixed amount of bus space which is
+ reserved for hotplug bridge's memory window.
+ Default size is 2 megabytes.
realloc= Enable/disable reallocating PCI bridge resources
if allocations done by BIOS are too small to
accommodate resources required by all child
projects / firefly-linux-kernel-4.4.55.git / blobdiff