/ {
memory {
device_type = "memory";
- reg = <0 0x80000000>;
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ backlight: backlight {
+ status = "disabled";
+ compatible = "pwm-backlight";
+ brightness-levels = <
+ 3 4 5 6 7
+ 8 9 10 11 12 13 14 15
+ 16 17 18 19 20 21 22 23
+ 24 25 26 27 28 29 30 31
+ 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47
+ 48 49 50 51 52 53 54 55
+ 56 57 58 59 60 61 62 63
+ 64 65 66 67 68 69 70 71
+ 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87
+ 88 89 90 91 92 93 94 95
+ 96 97 98 99 100 101 102 103
+ 104 105 106 107 108 109 110 111
+ 112 113 114 115 116 117 118 119
+ 120 121 122 123 124 125 126 127
+ 128 129 130 131 132 133 134 135
+ 136 137 138 139 140 141 142 143
+ 144 145 146 147 148 149 150 151
+ 152 153 154 155 156 157 158 159
+ 160 161 162 163 164 165 166 167
+ 168 169 170 171 172 173 174 175
+ 176 177 178 179 180 181 182 183
+ 184 185 186 187 188 189 190 191
+ 192 193 194 195 196 197 198 199
+ 200 201 202 203 204 205 206 207
+ 208 209 210 211 212 213 214 215
+ 216 217 218 219 220 221 222 223
+ 224 225 226 227 228 229 230 231
+ 232 233 234 235 236 237 238 239
+ 240 241 242 243 244 245 246 247
+ 248 249 250 251 252 253 254 255>;
+ default-brightness-level = <180>;
+ pwms = <&pwm1 0 25000 0>;
+ pwm-names = "backlight";
+ power-supply = <&vcc_sys>;
+ };
+
+ panel: panel {
+ status = "disabled";
+ compatible ="lg,lp079qx1-sp0v";
+ power-supply = <&vcc_sys>;
+ backlight = <&backlight>;
+ enable-gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>;
+
+ ports {
+ panel_in: port {
+ panel_in_edp: endpoint {
+ remote-endpoint = <&edp_out_panel>;
+ };
+ };
+ };
};
dovdd_1v8: dovdd-1v8-regulator {
clock-output-names = "ext_gmac";
};
- io_domains: io-domains {
- compatible = "rockchip,rk3288-io-voltage-domain";
- rockchip,grf = <&grf>;
-
- audio-supply = <&vcca_33>;
- bb-supply = <&vcc_io>;
- dvp-supply = <&dovdd_1v8>;
- flash0-supply = <&vcc_flash>;
- flash1-supply = <&vcc_lan>;
- gpio30-supply = <&vcc_io>;
- gpio1830-supply = <&vcc_io>;
- lcdc-supply = <&vcc_io>;
- sdcard-supply = <&vccio_sd>;
- wifi-supply = <&vccio_wl>;
- };
-
ir: ir-receiver {
compatible = "gpio-ir-receiver";
pinctrl-names = "default";
};
};
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&hym8563>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+
+ /*
+ * On the module itself this is one of these (depending
+ * on the actual card populated):
+ * - SDIO_RESET_L_WL_REG_ON
+ * - PDN (power down when low)
+ */
+ reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+ };
+
+ es8323-sound {
+ status = "okay";
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "rockchip,es8323-codec";
+ simple-audio-card,mclk-fs = <256>;
+ //simple-audio-card,hp-det-gpio = <&gpio7 15 GPIO_ACTIVE_HIGH>;
+ simple-audio-card,widgets =
+ "Microphone","Mic Jack",
+ "Headphone","Headphone Jack";
+ simple-audio-card,routing =
+ "Mic Jack","MICBIAS1",
+ "IN1P","Mic Jack",
+ "Headphone Jack","HPOL",
+ "Headphone Jack","HPOR";
+ simple-audio-card,cpu {
+ sound-dai = <&i2s>;
+ };
+ simple-audio-card,codec {
+ sound-dai = <&es8323>;
+ };
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "SPDIF";
+ simple-audio-card,dai-link@1 {
+ cpu { sound-dai = <&spdif>; };
+ codec { sound-dai = <&spdif_out>; };
+ };
+ };
+
+ spdif_out: spdif-out {
+ compatible = "linux,spdif-dit";
+ #sound-dai-cells = <0>;
+ };
+
vbat_wl: vcc_sys: vsys-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc_sys";
regulator-always-on;
vin-supply = <&vcc_io>;
};
+
+ wireless-bluetooth {
+ compatible = "bluetooth-platdata";
+ uart_rts_gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default", "rts_gpio";
+ pinctrl-0 = <&uart0_rts>;
+ pinctrl-1 = <&uart0_gpios>;
+ BT,reset_gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
+ BT,wake_gpio = <&gpio4 26 GPIO_ACTIVE_HIGH>;
+ BT,wake_host_irq = <&gpio4 31 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ wireless-wlan {
+ compatible = "wlan-platdata";
+ rockchip,grf = <&grf>;
+ wifi_chip_type = "ap6335";
+ sdio_vref = <1800>;
+ WIFI,host_wake_irq = <&gpio4 30 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
};
&cpu0 {
cpu0-supply = <&vdd_cpu>;
};
+&edp {
+ vcc-supply = <&vdd_10>;
+ vccio-supply = <&vcc_18>;
+ force-hpd;
+ status = "disabled";
+
+ ports {
+ edp_out: port@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ edp_out_panel: endpoint {
+ reg = <0>;
+ remote-endpoint = <&panel_in_edp>;
+ };
+ };
+ };
+};
+
+&edp_in {
+ /delete-node/ endpoint@0;
+};
+
+&edp_phy {
+ status = "disabled";
+ //status = "okay";
+};
+
&emmc {
bus-width = <8>;
cap-mmc-highspeed;
status = "ok";
};
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
&hdmi {
- ddc-i2c-bus = <&i2c5>;
status = "okay";
};
+&hevc_service {
+ status = "okay";
+
+};
+
+&hdmi_in {
+ /delete-node/ endpoint@1;
+};
+
&i2c0 {
clock-frequency = <400000>;
status = "okay";
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
+ regulator-ramp-delay = <6000>;
vin-supply = <&vcc_sys>;
};
regulator-name = "vcca_33";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ regulator-always-on;
};
vcc_lan: REG9 {
&i2c1 {
status = "okay";
+
+ mpu6050@68 {
+ compatible = "invensense,mpu6050";
+ reg = <0x68>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <RK_PB4 IRQ_TYPE_LEVEL_LOW>;
+ mount-matrix = "0",
+ "1",
+ "0",
+ "-1",
+ "0",
+ "0",
+ "0",
+ "0",
+ "-1";
+ };
};
&i2c2 {
status = "okay";
+
+ es8323: es8323@10 {
+ status = "okay";
+ compatible = "everest,es8323";
+ reg = <0x10>;
+ spk-con-gpio = <&gpio7 3 GPIO_ACTIVE_HIGH>;
+ hp-det-gpio = <&gpio7 15 GPIO_ACTIVE_LOW>;
+ clock-names = "mclk";
+ clocks = <&cru SCLK_I2S0_OUT>;
+ #sound-dai-cells = <0>;
+ };
};
&i2c4 {
status = "okay";
};
-&i2c5 {
+&io_domains {
+ status = "okay";
+
+ audio-supply = <&vcca_33>;
+ bb-supply = <&vcc_io>;
+ dvp-supply = <&dovdd_1v8>;
+ flash0-supply = <&vcc_flash>;
+ flash1-supply = <&vcc_lan>;
+ gpio30-supply = <&vcc_io>;
+ gpio1830-supply = <&vcc_io>;
+ lcdc-supply = <&vcc_io>;
+ sdcard-supply = <&vccio_sd>;
+ wifi-supply = <&vccio_wl>;
+};
+
+&rga {
status = "okay";
};
output-low;
};
+ pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+ drive-strength = <8>;
+ };
+
+ pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+ bias-pull-up;
+ drive-strength = <8>;
+ };
+
act8846 {
pwr_hold: pwr-hold {
rockchip,pins = <0 1 RK_FUNC_GPIO &pcfg_output_high>;
};
};
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <4 28 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
sdmmc {
+ /*
+ * Default drive strength isn't enough to achieve even
+ * high-speed mode on firefly board so bump up to 8ma.
+ */
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <6 17 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <6 18 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <6 19 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
sdmmc_pwr: sdmmc-pwr {
rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
};
rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
+
+ wireless-bluetooth {
+ uart0_gpios: uart0-gpios {
+ rockchip,pins = <4 19 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&i2s {
+ status = "okay";
+ #sound-dai-cells = <0>;
};
&saradc {
};
&sdio0 {
+ clock-frequency = <50000000>;
+ clock-freq-min-max = <200000 50000000>;
+
bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
disable-wp;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
non-removable;
num-slots = <1>;
pinctrl-names = "default";
- pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>;
+ pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk &sdio0_int>;
+ sd-uhs-sdr104;
+ supports-sdio;
vmmc-supply = <&vbat_wl>;
vqmmc-supply = <&vccio_wl>;
status = "okay";
num-slots = <1>;
pinctrl-names = "default";
pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>;
+ supports-sd;
vmmc-supply = <&vcc_sd>;
vqmmc-supply = <&vccio_sd>;
status = "okay";
};
+&spdif {
+ status = "okay";
+};
+
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi0_clk>, <&spi0_cs0>, <&spi0_tx>, <&spi0_rx>, <&spi0_cs1>;
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>;
+ pinctrl-0 = <&uart0_xfer>, <&uart0_cts>;
status = "okay";
};
status = "okay";
};
+&vopb_out {
+ /delete-node/ endpoint@1;
+};
+
&vopl {
status = "okay";
};
status = "okay";
};
+&vpu_service {
+ status = "okay";
+};
+
+&vopl_out {
+ /delete-node/ endpoint@0;
+};
+
&wdt {
status = "okay";
};