#include <linux/timer.h>
#include <linux/init.h>
#include <linux/sysdev.h>
+#include <linux/delay.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
+#include <linux/i2c.h>
+
+#include <video/ili9320.h>
+
+#include <linux/spi/spi.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <asm/plat-s3c/regs-serial.h>
#include <asm/plat-s3c/nand.h>
+#include <asm/plat-s3c/iic.h>
-#include <asm/arch/regs-power.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-lcd.h>
-#include <asm/arch/fb.h>
+#include <mach/regs-power.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
+#include <mach/spi-gpio.h>
+#include <mach/fb.h>
#include <asm/mach-types.h>
S3C2410_GPDCON_MASK(14) | S3C2410_GPDCON_MASK(15)),
};
+/* ILI9320 support. */
+
+static void jive_lcm_reset(unsigned int set)
+{
+ printk(KERN_DEBUG "%s(%d)\n", __func__, set);
+
+ s3c2410_gpio_setpin(S3C2410_GPG13, set);
+ s3c2410_gpio_cfgpin(S3C2410_GPG13, S3C2410_GPIO_OUTPUT);
+}
+
+#undef LCD_UPPER_MARGIN
+#define LCD_UPPER_MARGIN 2
+
+static struct ili9320_platdata jive_lcm_config = {
+ .hsize = LCD_XRES,
+ .vsize = LCD_YRES,
+
+ .reset = jive_lcm_reset,
+ .suspend = ILI9320_SUSPEND_DEEP,
+
+ .entry_mode = ILI9320_ENTRYMODE_ID(3) | ILI9320_ENTRYMODE_BGR,
+ .display2 = (ILI9320_DISPLAY2_FP(LCD_UPPER_MARGIN) |
+ ILI9320_DISPLAY2_BP(LCD_LOWER_MARGIN)),
+ .display3 = 0x0,
+ .display4 = 0x0,
+ .rgb_if1 = (ILI9320_RGBIF1_RIM_RGB18 |
+ ILI9320_RGBIF1_RM | ILI9320_RGBIF1_CLK_RGBIF),
+ .rgb_if2 = ILI9320_RGBIF2_DPL,
+ .interface2 = 0x0,
+ .interface3 = 0x3,
+ .interface4 = (ILI9320_INTERFACE4_RTNE(16) |
+ ILI9320_INTERFACE4_DIVE(1)),
+ .interface5 = 0x0,
+ .interface6 = 0x0,
+};
+
+/* LCD SPI support */
+
+static void jive_lcd_spi_chipselect(struct s3c2410_spigpio_info *spi, int cs)
+{
+ s3c2410_gpio_setpin(S3C2410_GPB7, cs ? 0 : 1);
+}
+
+static struct s3c2410_spigpio_info jive_lcd_spi = {
+ .bus_num = 0,
+ .pin_clk = S3C2410_GPG8,
+ .pin_mosi = S3C2410_GPB8,
+ .chip_select = jive_lcd_spi_chipselect,
+};
+
+static struct platform_device jive_device_lcdspi = {
+ .name = "s3c24xx-spi-gpio",
+ .id = 1,
+ .num_resources = 0,
+ .dev.platform_data = &jive_lcd_spi,
+};
+
+/* WM8750 audio code SPI definition */
+
+static void jive_wm8750_chipselect(struct s3c2410_spigpio_info *spi, int cs)
+{
+ s3c2410_gpio_setpin(S3C2410_GPH10, cs ? 0 : 1);
+}
+
+static struct s3c2410_spigpio_info jive_wm8750_spi = {
+ .bus_num = 2,
+ .pin_clk = S3C2410_GPB4,
+ .pin_mosi = S3C2410_GPB9,
+ .chip_select = jive_wm8750_chipselect,
+};
+
+static struct platform_device jive_device_wm8750 = {
+ .name = "s3c24xx-spi-gpio",
+ .id = 2,
+ .num_resources = 0,
+ .dev.platform_data = &jive_wm8750_spi,
+};
+
+/* JIVE SPI devices. */
+
+static struct spi_board_info __initdata jive_spi_devs[] = {
+ [0] = {
+ .modalias = "VGG2432A4",
+ .bus_num = 1,
+ .chip_select = 0,
+ .mode = SPI_MODE_3, /* CPOL=1, CPHA=1 */
+ .max_speed_hz = 100000,
+ .platform_data = &jive_lcm_config,
+ }, {
+ .modalias = "WM8750",
+ .bus_num = 2,
+ .chip_select = 0,
+ .mode = SPI_MODE_0, /* CPOL=0, CPHA=0 */
+ .max_speed_hz = 100000,
+ },
+};
+
+/* I2C bus and device configuration. */
+
+static struct s3c2410_platform_i2c jive_i2c_cfg = {
+ .max_freq = 80 * 1000,
+ .bus_freq = 50 * 1000,
+ .flags = S3C_IICFLG_FILTER,
+ .sda_delay = 2,
+};
+
+static struct i2c_board_info jive_i2c_devs[] = {
+ [0] = {
+ I2C_BOARD_INFO("lis302dl", 0x1c),
+ .irq = IRQ_EINT14,
+ },
+};
+
+/* The platform devices being used. */
+
static struct platform_device *jive_devices[] __initdata = {
&s3c_device_usb,
&s3c_device_rtc,
&s3c_device_wdt,
&s3c_device_i2c,
&s3c_device_lcd,
+ &jive_device_lcdspi,
+ &jive_device_wm8750,
&s3c_device_nand,
&s3c_device_usbgadget,
};
s3c24xx_init_uarts(jive_uartcfgs, ARRAY_SIZE(jive_uartcfgs));
}
+static void jive_power_off(void)
+{
+ printk(KERN_INFO "powering system down...\n");
+
+ s3c2410_gpio_setpin(S3C2410_GPC5, 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPC5, S3C2410_GPIO_OUTPUT);
+}
+
static void __init jive_machine_init(void)
{
/* register system devices for managing low level suspend */
s3c_device_nand.dev.platform_data = &jive_nand_info;
+ /* initialise the spi */
+
+ s3c2410_gpio_setpin(S3C2410_GPG13, 0);
+ s3c2410_gpio_cfgpin(S3C2410_GPG13, S3C2410_GPIO_OUTPUT);
+
+ s3c2410_gpio_setpin(S3C2410_GPB7, 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPB7, S3C2410_GPIO_OUTPUT);
+
+ s3c2410_gpio_setpin(S3C2410_GPB6, 0);
+ s3c2410_gpio_cfgpin(S3C2410_GPB6, S3C2410_GPIO_OUTPUT);
+
+ s3c2410_gpio_setpin(S3C2410_GPG8, 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPG8, S3C2410_GPIO_OUTPUT);
+
+ /* initialise the WM8750 spi */
+
+ s3c2410_gpio_setpin(S3C2410_GPH10, 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPH10, S3C2410_GPIO_OUTPUT);
+
/* Turn off suspend on both USB ports, and switch the
* selectable USB port to USB device mode. */
s3c24xx_udc_set_platdata(&jive_udc_cfg);
s3c24xx_fb_set_platdata(&jive_lcd_config);
+ spi_register_board_info(jive_spi_devs, ARRAY_SIZE(jive_spi_devs));
+
+ s3c_device_i2c.dev.platform_data = &jive_i2c_cfg;
+ i2c_register_board_info(0, jive_i2c_devs, ARRAY_SIZE(jive_i2c_devs));
+
+ pm_power_off = jive_power_off;
+
platform_add_devices(jive_devices, ARRAY_SIZE(jive_devices));
}
projects / firefly-linux-kernel-4.4.55.git / blobdiff