#include "generic.h"
#define ASSABET_BCR_DB1110 \
- (ASSABET_BCR_SPK_OFF | ASSABET_BCR_QMUTE | \
+ (ASSABET_BCR_SPK_OFF | \
ASSABET_BCR_LED_GREEN | ASSABET_BCR_LED_RED | \
ASSABET_BCR_RS232EN | ASSABET_BCR_LCD_12RGB | \
ASSABET_BCR_IRDA_MD0)
#define ASSABET_BCR_DB1111 \
- (ASSABET_BCR_SPK_OFF | ASSABET_BCR_QMUTE | \
+ (ASSABET_BCR_SPK_OFF | \
ASSABET_BCR_LED_GREEN | ASSABET_BCR_LED_RED | \
ASSABET_BCR_RS232EN | ASSABET_BCR_LCD_12RGB | \
ASSABET_BCR_CF_BUS_OFF | ASSABET_BCR_STEREO_LB | \
};
static struct resource assabet_flash_resources[] = {
- {
- .start = SA1100_CS0_PHYS,
- .end = SA1100_CS0_PHYS + SZ_32M - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = SA1100_CS1_PHYS,
- .end = SA1100_CS1_PHYS + SZ_32M - 1,
- .flags = IORESOURCE_MEM,
- }
+ DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_32M),
+ DEFINE_RES_MEM(SA1100_CS1_PHYS, SZ_32M),
};
static struct mcp_plat_data assabet_mcp_data = {
.mccr0 = MCCR0_ADM,
.sclk_rate = 11981000,
- .codec = "ucb1x00",
};
+#ifdef CONFIG_ASSABET_NEPONSET
+static struct resource neponset_resources[] = {
+ DEFINE_RES_MEM(0x10000000, 0x08000000),
+ DEFINE_RES_MEM(0x18000000, 0x04000000),
+ DEFINE_RES_MEM(0x40000000, SZ_8K),
+ DEFINE_RES_IRQ(IRQ_GPIO25),
+};
+#endif
+
static void __init assabet_init(void)
{
/*
* Ensure that the power supply is in "high power" mode.
*/
- GPDR |= GPIO_GPIO16;
GPSR = GPIO_GPIO16;
+ GPDR |= GPIO_GPIO16;
/*
* Ensure that these pins are set as outputs and are driving
* the WS latch in the CPLD, and we don't float causing
* excessive power drain. --rmk
*/
- GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
GPCR = GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
+ GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
+
+ /*
+ * Also set GPIO27 as an output; this is used to clock UART3
+ * via the FPGA and as otherwise has no pullups or pulldowns,
+ * so stop it floating.
+ */
+ GPCR = GPIO_GPIO27;
+ GPDR |= GPIO_GPIO27;
/*
* Set up registers for sleep mode.
#ifndef CONFIG_ASSABET_NEPONSET
printk( "Warning: Neponset detected but full support "
"hasn't been configured in the kernel\n" );
+#else
+ platform_device_register_simple("neponset", 0,
+ neponset_resources, ARRAY_SIZE(neponset_resources));
#endif
}
sa11x0_register_mtd(&assabet_flash_data, assabet_flash_resources,
ARRAY_SIZE(assabet_flash_resources));
sa11x0_register_irda(&assabet_irda_data);
-
- /*
- * Setup the PPC unit correctly.
- */
- PPDR &= ~PPC_RXD4;
- PPDR |= PPC_TXD4 | PPC_SCLK | PPC_SFRM;
- PSDR |= PPC_RXD4;
- PSDR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
- PPSR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
-
- ASSABET_BCR_set(ASSABET_BCR_CODEC_RST);
sa11x0_register_mcp(&assabet_mcp_data);
}
*/
Ser1SDCR0 |= SDCR0_SUS;
- if (machine_has_neponset()) {
-#ifdef CONFIG_ASSABET_NEPONSET
- extern void neponset_map_io(void);
-
- /*
- * We map Neponset registers even if it isn't present since
- * many drivers will try to probe their stuff (and fail).
- * This is still more friendly than a kernel paging request
- * crash.
- */
- neponset_map_io();
-#endif
- } else {
+ if (!machine_has_neponset())
sa1100_register_uart_fns(&assabet_port_fns);
- }
/*
* When Neponset is attached, the first UART should be