int eeh_subsystem_enabled;
EXPORT_SYMBOL(eeh_subsystem_enabled);
+/*
+ * EEH probe mode support. The intention is to support multiple
+ * platforms for EEH. Some platforms like pSeries do PCI emunation
+ * based on device tree. However, other platforms like powernv probe
+ * PCI devices from hardware. The flag is used to distinguish that.
+ * In addition, struct eeh_ops::probe would be invoked for particular
+ * OF node or PCI device so that the corresponding PE would be created
+ * there.
+ */
+int eeh_probe_mode;
+
+/* Global EEH mutex */
+DEFINE_MUTEX(eeh_mutex);
+
/* Lock to avoid races due to multiple reports of an error */
static DEFINE_RAW_SPINLOCK(confirm_error_lock);
}
}
- /* Gather status on devices under the bridge */
- if (dev->class >> 16 == PCI_BASE_CLASS_BRIDGE) {
- struct device_node *child;
-
- for_each_child_of_node(dn, child) {
- if (of_node_to_eeh_dev(child))
- n += eeh_gather_pci_data(of_node_to_eeh_dev(child), buf+n, len-n);
- }
- }
-
return n;
}
/**
* eeh_slot_error_detail - Generate combined log including driver log and error log
- * @edev: device to report error log for
+ * @pe: EEH PE
* @severity: temporary or permanent error log
*
* This routine should be called to generate the combined log, which
* out from the config space of the corresponding PCI device, while
* the error log is fetched through platform dependent function call.
*/
-void eeh_slot_error_detail(struct eeh_dev *edev, int severity)
+void eeh_slot_error_detail(struct eeh_pe *pe, int severity)
{
size_t loglen = 0;
- pci_regs_buf[0] = 0;
+ struct eeh_dev *edev;
- eeh_pci_enable(edev, EEH_OPT_THAW_MMIO);
- eeh_ops->configure_bridge(eeh_dev_to_of_node(edev));
- eeh_restore_bars(edev);
- loglen = eeh_gather_pci_data(edev, pci_regs_buf, EEH_PCI_REGS_LOG_LEN);
+ eeh_pci_enable(pe, EEH_OPT_THAW_MMIO);
+ eeh_ops->configure_bridge(pe);
+ eeh_pe_restore_bars(pe);
- eeh_ops->get_log(eeh_dev_to_of_node(edev), severity, pci_regs_buf, loglen);
+ pci_regs_buf[0] = 0;
+ eeh_pe_for_each_dev(pe, edev) {
+ loglen += eeh_gather_pci_data(edev, pci_regs_buf,
+ EEH_PCI_REGS_LOG_LEN);
+ }
+
+ eeh_ops->get_log(pe, severity, pci_regs_buf, loglen);
}
/**
}
/**
- * eeh_find_device_pe - Retrieve the PE for the given device
- * @dn: device node
- *
- * Return the PE under which this device lies
- */
-struct device_node *eeh_find_device_pe(struct device_node *dn)
-{
- while (dn->parent && of_node_to_eeh_dev(dn->parent) &&
- (of_node_to_eeh_dev(dn->parent)->mode & EEH_MODE_SUPPORTED)) {
- dn = dn->parent;
- }
- return dn;
-}
-
-/**
- * __eeh_mark_slot - Mark all child devices as failed
- * @parent: parent device
- * @mode_flag: failure flag
- *
- * Mark all devices that are children of this device as failed.
- * Mark the device driver too, so that it can see the failure
- * immediately; this is critical, since some drivers poll
- * status registers in interrupts ... If a driver is polling,
- * and the slot is frozen, then the driver can deadlock in
- * an interrupt context, which is bad.
- */
-static void __eeh_mark_slot(struct device_node *parent, int mode_flag)
-{
- struct device_node *dn;
-
- for_each_child_of_node(parent, dn) {
- if (of_node_to_eeh_dev(dn)) {
- /* Mark the pci device driver too */
- struct pci_dev *dev = of_node_to_eeh_dev(dn)->pdev;
-
- of_node_to_eeh_dev(dn)->mode |= mode_flag;
-
- if (dev && dev->driver)
- dev->error_state = pci_channel_io_frozen;
-
- __eeh_mark_slot(dn, mode_flag);
- }
- }
-}
-
-/**
- * eeh_mark_slot - Mark the indicated device and its children as failed
- * @dn: parent device
- * @mode_flag: failure flag
- *
- * Mark the indicated device and its child devices as failed.
- * The device drivers are marked as failed as well.
- */
-void eeh_mark_slot(struct device_node *dn, int mode_flag)
-{
- struct pci_dev *dev;
- dn = eeh_find_device_pe(dn);
-
- /* Back up one, since config addrs might be shared */
- if (!pcibios_find_pci_bus(dn) && of_node_to_eeh_dev(dn->parent))
- dn = dn->parent;
-
- of_node_to_eeh_dev(dn)->mode |= mode_flag;
-
- /* Mark the pci device too */
- dev = of_node_to_eeh_dev(dn)->pdev;
- if (dev)
- dev->error_state = pci_channel_io_frozen;
-
- __eeh_mark_slot(dn, mode_flag);
-}
-
-/**
- * __eeh_clear_slot - Clear failure flag for the child devices
- * @parent: parent device
- * @mode_flag: flag to be cleared
- *
- * Clear failure flag for the child devices.
- */
-static void __eeh_clear_slot(struct device_node *parent, int mode_flag)
-{
- struct device_node *dn;
-
- for_each_child_of_node(parent, dn) {
- if (of_node_to_eeh_dev(dn)) {
- of_node_to_eeh_dev(dn)->mode &= ~mode_flag;
- of_node_to_eeh_dev(dn)->check_count = 0;
- __eeh_clear_slot(dn, mode_flag);
- }
- }
-}
-
-/**
- * eeh_clear_slot - Clear failure flag for the indicated device and its children
- * @dn: parent device
- * @mode_flag: flag to be cleared
- *
- * Clear failure flag for the indicated device and its children.
- */
-void eeh_clear_slot(struct device_node *dn, int mode_flag)
-{
- unsigned long flags;
- raw_spin_lock_irqsave(&confirm_error_lock, flags);
-
- dn = eeh_find_device_pe(dn);
-
- /* Back up one, since config addrs might be shared */
- if (!pcibios_find_pci_bus(dn) && of_node_to_eeh_dev(dn->parent))
- dn = dn->parent;
-
- of_node_to_eeh_dev(dn)->mode &= ~mode_flag;
- of_node_to_eeh_dev(dn)->check_count = 0;
- __eeh_clear_slot(dn, mode_flag);
- raw_spin_unlock_irqrestore(&confirm_error_lock, flags);
-}
-
-/**
- * eeh_dn_check_failure - Check if all 1's data is due to EEH slot freeze
- * @dn: device node
- * @dev: pci device, if known
+ * eeh_dev_check_failure - Check if all 1's data is due to EEH slot freeze
+ * @edev: eeh device
*
* Check for an EEH failure for the given device node. Call this
* routine if the result of a read was all 0xff's and you want to
*
* It is safe to call this routine in an interrupt context.
*/
-int eeh_dn_check_failure(struct device_node *dn, struct pci_dev *dev)
+int eeh_dev_check_failure(struct eeh_dev *edev)
{
int ret;
unsigned long flags;
- struct eeh_dev *edev;
+ struct device_node *dn;
+ struct pci_dev *dev;
+ struct eeh_pe *pe;
int rc = 0;
const char *location;
if (!eeh_subsystem_enabled)
return 0;
- if (!dn) {
+ if (!edev) {
eeh_stats.no_dn++;
return 0;
}
- dn = eeh_find_device_pe(dn);
- edev = of_node_to_eeh_dev(dn);
+ dn = eeh_dev_to_of_node(edev);
+ dev = eeh_dev_to_pci_dev(edev);
+ pe = edev->pe;
/* Access to IO BARs might get this far and still not want checking. */
- if (!(edev->mode & EEH_MODE_SUPPORTED) ||
- edev->mode & EEH_MODE_NOCHECK) {
+ if (!pe) {
eeh_stats.ignored_check++;
- pr_debug("EEH: Ignored check (%x) for %s %s\n",
- edev->mode, eeh_pci_name(dev), dn->full_name);
+ pr_debug("EEH: Ignored check for %s %s\n",
+ eeh_pci_name(dev), dn->full_name);
return 0;
}
- if (!edev->config_addr && !edev->pe_config_addr) {
+ if (!pe->addr && !pe->config_addr) {
eeh_stats.no_cfg_addr++;
return 0;
}
*/
raw_spin_lock_irqsave(&confirm_error_lock, flags);
rc = 1;
- if (edev->mode & EEH_MODE_ISOLATED) {
- edev->check_count++;
- if (edev->check_count % EEH_MAX_FAILS == 0) {
+ if (pe->state & EEH_PE_ISOLATED) {
+ pe->check_count++;
+ if (pe->check_count % EEH_MAX_FAILS == 0) {
location = of_get_property(dn, "ibm,loc-code", NULL);
printk(KERN_ERR "EEH: %d reads ignored for recovering device at "
"location=%s driver=%s pci addr=%s\n",
- edev->check_count, location,
+ pe->check_count, location,
eeh_driver_name(dev), eeh_pci_name(dev));
printk(KERN_ERR "EEH: Might be infinite loop in %s driver\n",
eeh_driver_name(dev));
* function zero of a multi-function device.
* In any case they must share a common PHB.
*/
- ret = eeh_ops->get_state(dn, NULL);
+ ret = eeh_ops->get_state(pe, NULL);
/* Note that config-io to empty slots may fail;
* they are empty when they don't have children.
(ret & (EEH_STATE_MMIO_ACTIVE | EEH_STATE_DMA_ACTIVE)) ==
(EEH_STATE_MMIO_ACTIVE | EEH_STATE_DMA_ACTIVE)) {
eeh_stats.false_positives++;
- edev->false_positives ++;
+ pe->false_positives++;
rc = 0;
goto dn_unlock;
}
* with other functions on this device, and functions under
* bridges.
*/
- eeh_mark_slot(dn, EEH_MODE_ISOLATED);
+ eeh_pe_state_mark(pe, EEH_PE_ISOLATED);
raw_spin_unlock_irqrestore(&confirm_error_lock, flags);
- eeh_send_failure_event(edev);
+ eeh_send_failure_event(pe);
/* Most EEH events are due to device driver bugs. Having
* a stack trace will help the device-driver authors figure
return rc;
}
-EXPORT_SYMBOL_GPL(eeh_dn_check_failure);
+EXPORT_SYMBOL_GPL(eeh_dev_check_failure);
/**
* eeh_check_failure - Check if all 1's data is due to EEH slot freeze
unsigned long eeh_check_failure(const volatile void __iomem *token, unsigned long val)
{
unsigned long addr;
- struct pci_dev *dev;
- struct device_node *dn;
+ struct eeh_dev *edev;
/* Finding the phys addr + pci device; this is pretty quick. */
addr = eeh_token_to_phys((unsigned long __force) token);
- dev = pci_addr_cache_get_device(addr);
- if (!dev) {
+ edev = eeh_addr_cache_get_dev(addr);
+ if (!edev) {
eeh_stats.no_device++;
return val;
}
- dn = pci_device_to_OF_node(dev);
- eeh_dn_check_failure(dn, dev);
+ eeh_dev_check_failure(edev);
- pci_dev_put(dev);
+ pci_dev_put(eeh_dev_to_pci_dev(edev));
return val;
}
/**
* eeh_pci_enable - Enable MMIO or DMA transfers for this slot
- * @edev: pci device node
+ * @pe: EEH PE
*
* This routine should be called to reenable frozen MMIO or DMA
* so that it would work correctly again. It's useful while doing
* recovery or log collection on the indicated device.
*/
-int eeh_pci_enable(struct eeh_dev *edev, int function)
+int eeh_pci_enable(struct eeh_pe *pe, int function)
{
int rc;
- struct device_node *dn = eeh_dev_to_of_node(edev);
- rc = eeh_ops->set_option(dn, function);
+ rc = eeh_ops->set_option(pe, function);
if (rc)
- printk(KERN_WARNING "EEH: Unexpected state change %d, err=%d dn=%s\n",
- function, rc, dn->full_name);
+ pr_warning("%s: Unexpected state change %d on PHB#%d-PE#%x, err=%d\n",
+ __func__, function, pe->phb->global_number, pe->addr, rc);
- rc = eeh_ops->wait_state(dn, PCI_BUS_RESET_WAIT_MSEC);
+ rc = eeh_ops->wait_state(pe, PCI_BUS_RESET_WAIT_MSEC);
if (rc > 0 && (rc & EEH_STATE_MMIO_ENABLED) &&
(function == EEH_OPT_THAW_MMIO))
return 0;
*/
int pcibios_set_pcie_reset_state(struct pci_dev *dev, enum pcie_reset_state state)
{
- struct device_node *dn = pci_device_to_OF_node(dev);
+ struct eeh_dev *edev = pci_dev_to_eeh_dev(dev);
+ struct eeh_pe *pe = edev->pe;
+
+ if (!pe) {
+ pr_err("%s: No PE found on PCI device %s\n",
+ __func__, pci_name(dev));
+ return -EINVAL;
+ }
switch (state) {
case pcie_deassert_reset:
- eeh_ops->reset(dn, EEH_RESET_DEACTIVATE);
+ eeh_ops->reset(pe, EEH_RESET_DEACTIVATE);
break;
case pcie_hot_reset:
- eeh_ops->reset(dn, EEH_RESET_HOT);
+ eeh_ops->reset(pe, EEH_RESET_HOT);
break;
case pcie_warm_reset:
- eeh_ops->reset(dn, EEH_RESET_FUNDAMENTAL);
+ eeh_ops->reset(pe, EEH_RESET_FUNDAMENTAL);
break;
default:
return -EINVAL;
}
/**
- * __eeh_set_pe_freset - Check the required reset for child devices
- * @parent: parent device
- * @freset: return value
- *
- * Each device might have its preferred reset type: fundamental or
- * hot reset. The routine is used to collect the information from
- * the child devices so that they could be reset accordingly.
- */
-void __eeh_set_pe_freset(struct device_node *parent, unsigned int *freset)
-{
- struct device_node *dn;
-
- for_each_child_of_node(parent, dn) {
- if (of_node_to_eeh_dev(dn)) {
- struct pci_dev *dev = of_node_to_eeh_dev(dn)->pdev;
-
- if (dev && dev->driver)
- *freset |= dev->needs_freset;
-
- __eeh_set_pe_freset(dn, freset);
- }
- }
-}
-
-/**
- * eeh_set_pe_freset - Check the required reset for the indicated device and its children
- * @dn: parent device
- * @freset: return value
+ * eeh_set_pe_freset - Check the required reset for the indicated device
+ * @data: EEH device
+ * @flag: return value
*
* Each device might have its preferred reset type: fundamental or
* hot reset. The routine is used to collected the information for
* the indicated device and its children so that the bunch of the
* devices could be reset properly.
*/
-void eeh_set_pe_freset(struct device_node *dn, unsigned int *freset)
+static void *eeh_set_dev_freset(void *data, void *flag)
{
struct pci_dev *dev;
- dn = eeh_find_device_pe(dn);
-
- /* Back up one, since config addrs might be shared */
- if (!pcibios_find_pci_bus(dn) && of_node_to_eeh_dev(dn->parent))
- dn = dn->parent;
+ unsigned int *freset = (unsigned int *)flag;
+ struct eeh_dev *edev = (struct eeh_dev *)data;
- dev = of_node_to_eeh_dev(dn)->pdev;
+ dev = eeh_dev_to_pci_dev(edev);
if (dev)
*freset |= dev->needs_freset;
- __eeh_set_pe_freset(dn, freset);
+ return NULL;
}
/**
* eeh_reset_pe_once - Assert the pci #RST line for 1/4 second
- * @edev: pci device node to be reset.
+ * @pe: EEH PE
*
* Assert the PCI #RST line for 1/4 second.
*/
-static void eeh_reset_pe_once(struct eeh_dev *edev)
+static void eeh_reset_pe_once(struct eeh_pe *pe)
{
unsigned int freset = 0;
- struct device_node *dn = eeh_dev_to_of_node(edev);
/* Determine type of EEH reset required for
* Partitionable Endpoint, a hot-reset (1)
* A fundamental reset required by any device under
* Partitionable Endpoint trumps hot-reset.
*/
- eeh_set_pe_freset(dn, &freset);
+ eeh_pe_dev_traverse(pe, eeh_set_dev_freset, &freset);
if (freset)
- eeh_ops->reset(dn, EEH_RESET_FUNDAMENTAL);
+ eeh_ops->reset(pe, EEH_RESET_FUNDAMENTAL);
else
- eeh_ops->reset(dn, EEH_RESET_HOT);
+ eeh_ops->reset(pe, EEH_RESET_HOT);
/* The PCI bus requires that the reset be held high for at least
* a 100 milliseconds. We wait a bit longer 'just in case'.
* pci slot reset line is dropped. Make sure we don't miss
* these, and clear the flag now.
*/
- eeh_clear_slot(dn, EEH_MODE_ISOLATED);
+ eeh_pe_state_clear(pe, EEH_PE_ISOLATED);
- eeh_ops->reset(dn, EEH_RESET_DEACTIVATE);
+ eeh_ops->reset(pe, EEH_RESET_DEACTIVATE);
/* After a PCI slot has been reset, the PCI Express spec requires
* a 1.5 second idle time for the bus to stabilize, before starting
/**
* eeh_reset_pe - Reset the indicated PE
- * @edev: PCI device associated EEH device
+ * @pe: EEH PE
*
* This routine should be called to reset indicated device, including
* PE. A PE might include multiple PCI devices and sometimes PCI bridges
* might be involved as well.
*/
-int eeh_reset_pe(struct eeh_dev *edev)
+int eeh_reset_pe(struct eeh_pe *pe)
{
int i, rc;
- struct device_node *dn = eeh_dev_to_of_node(edev);
/* Take three shots at resetting the bus */
for (i=0; i<3; i++) {
- eeh_reset_pe_once(edev);
+ eeh_reset_pe_once(pe);
- rc = eeh_ops->wait_state(dn, PCI_BUS_RESET_WAIT_MSEC);
+ rc = eeh_ops->wait_state(pe, PCI_BUS_RESET_WAIT_MSEC);
if (rc == (EEH_STATE_MMIO_ACTIVE | EEH_STATE_DMA_ACTIVE))
return 0;
if (rc < 0) {
- printk(KERN_ERR "EEH: unrecoverable slot failure %s\n",
- dn->full_name);
+ pr_err("%s: Unrecoverable slot failure on PHB#%d-PE#%x",
+ __func__, pe->phb->global_number, pe->addr);
return -1;
}
- printk(KERN_ERR "EEH: bus reset %d failed on slot %s, rc=%d\n",
- i+1, dn->full_name, rc);
+ pr_err("EEH: bus reset %d failed on PHB#%d-PE#%x, rc=%d\n",
+ i+1, pe->phb->global_number, pe->addr, rc);
}
return -1;
}
-/** Save and restore of PCI BARs
- *
- * Although firmware will set up BARs during boot, it doesn't
- * set up device BAR's after a device reset, although it will,
- * if requested, set up bridge configuration. Thus, we need to
- * configure the PCI devices ourselves.
- */
-
-/**
- * eeh_restore_one_device_bars - Restore the Base Address Registers for one device
- * @edev: PCI device associated EEH device
- *
- * Loads the PCI configuration space base address registers,
- * the expansion ROM base address, the latency timer, and etc.
- * from the saved values in the device node.
- */
-static inline void eeh_restore_one_device_bars(struct eeh_dev *edev)
-{
- int i;
- u32 cmd;
- struct device_node *dn = eeh_dev_to_of_node(edev);
-
- if (!edev->phb)
- return;
-
- for (i=4; i<10; i++) {
- eeh_ops->write_config(dn, i*4, 4, edev->config_space[i]);
- }
-
- /* 12 == Expansion ROM Address */
- eeh_ops->write_config(dn, 12*4, 4, edev->config_space[12]);
-
-#define BYTE_SWAP(OFF) (8*((OFF)/4)+3-(OFF))
-#define SAVED_BYTE(OFF) (((u8 *)(edev->config_space))[BYTE_SWAP(OFF)])
-
- eeh_ops->write_config(dn, PCI_CACHE_LINE_SIZE, 1,
- SAVED_BYTE(PCI_CACHE_LINE_SIZE));
-
- eeh_ops->write_config(dn, PCI_LATENCY_TIMER, 1,
- SAVED_BYTE(PCI_LATENCY_TIMER));
-
- /* max latency, min grant, interrupt pin and line */
- eeh_ops->write_config(dn, 15*4, 4, edev->config_space[15]);
-
- /* Restore PERR & SERR bits, some devices require it,
- * don't touch the other command bits
- */
- eeh_ops->read_config(dn, PCI_COMMAND, 4, &cmd);
- if (edev->config_space[1] & PCI_COMMAND_PARITY)
- cmd |= PCI_COMMAND_PARITY;
- else
- cmd &= ~PCI_COMMAND_PARITY;
- if (edev->config_space[1] & PCI_COMMAND_SERR)
- cmd |= PCI_COMMAND_SERR;
- else
- cmd &= ~PCI_COMMAND_SERR;
- eeh_ops->write_config(dn, PCI_COMMAND, 4, cmd);
-}
-
-/**
- * eeh_restore_bars - Restore the PCI config space info
- * @edev: EEH device
- *
- * This routine performs a recursive walk to the children
- * of this device as well.
- */
-void eeh_restore_bars(struct eeh_dev *edev)
-{
- struct device_node *dn;
- if (!edev)
- return;
-
- if ((edev->mode & EEH_MODE_SUPPORTED) && !IS_BRIDGE(edev->class_code))
- eeh_restore_one_device_bars(edev);
-
- for_each_child_of_node(eeh_dev_to_of_node(edev), dn)
- eeh_restore_bars(of_node_to_eeh_dev(dn));
-}
-
/**
* eeh_save_bars - Save device bars
* @edev: PCI device associated EEH device
* PCI devices are added individually; but, for the restore,
* an entire slot is reset at a time.
*/
-static void eeh_save_bars(struct eeh_dev *edev)
+void eeh_save_bars(struct eeh_dev *edev)
{
int i;
struct device_node *dn;
eeh_ops->read_config(dn, i * 4, 4, &edev->config_space[i]);
}
-/**
- * eeh_early_enable - Early enable EEH on the indicated device
- * @dn: device node
- * @data: BUID
- *
- * Enable EEH functionality on the specified PCI device. The function
- * is expected to be called before real PCI probing is done. However,
- * the PHBs have been initialized at this point.
- */
-static void *eeh_early_enable(struct device_node *dn, void *data)
-{
- int ret;
- const u32 *class_code = of_get_property(dn, "class-code", NULL);
- const u32 *vendor_id = of_get_property(dn, "vendor-id", NULL);
- const u32 *device_id = of_get_property(dn, "device-id", NULL);
- const u32 *regs;
- int enable;
- struct eeh_dev *edev = of_node_to_eeh_dev(dn);
-
- edev->class_code = 0;
- edev->mode = 0;
- edev->check_count = 0;
- edev->freeze_count = 0;
- edev->false_positives = 0;
-
- if (!of_device_is_available(dn))
- return NULL;
-
- /* Ignore bad nodes. */
- if (!class_code || !vendor_id || !device_id)
- return NULL;
-
- /* There is nothing to check on PCI to ISA bridges */
- if (dn->type && !strcmp(dn->type, "isa")) {
- edev->mode |= EEH_MODE_NOCHECK;
- return NULL;
- }
- edev->class_code = *class_code;
-
- /* Ok... see if this device supports EEH. Some do, some don't,
- * and the only way to find out is to check each and every one.
- */
- regs = of_get_property(dn, "reg", NULL);
- if (regs) {
- /* First register entry is addr (00BBSS00) */
- /* Try to enable eeh */
- ret = eeh_ops->set_option(dn, EEH_OPT_ENABLE);
-
- enable = 0;
- if (ret == 0) {
- edev->config_addr = regs[0];
-
- /* If the newer, better, ibm,get-config-addr-info is supported,
- * then use that instead.
- */
- edev->pe_config_addr = eeh_ops->get_pe_addr(dn);
-
- /* Some older systems (Power4) allow the
- * ibm,set-eeh-option call to succeed even on nodes
- * where EEH is not supported. Verify support
- * explicitly.
- */
- ret = eeh_ops->get_state(dn, NULL);
- if (ret > 0 && ret != EEH_STATE_NOT_SUPPORT)
- enable = 1;
- }
-
- if (enable) {
- eeh_subsystem_enabled = 1;
- edev->mode |= EEH_MODE_SUPPORTED;
-
- pr_debug("EEH: %s: eeh enabled, config=%x pe_config=%x\n",
- dn->full_name, edev->config_addr,
- edev->pe_config_addr);
- } else {
-
- /* This device doesn't support EEH, but it may have an
- * EEH parent, in which case we mark it as supported.
- */
- if (dn->parent && of_node_to_eeh_dev(dn->parent) &&
- (of_node_to_eeh_dev(dn->parent)->mode & EEH_MODE_SUPPORTED)) {
- /* Parent supports EEH. */
- edev->mode |= EEH_MODE_SUPPORTED;
- edev->config_addr = of_node_to_eeh_dev(dn->parent)->config_addr;
- return NULL;
- }
- }
- } else {
- printk(KERN_WARNING "EEH: %s: unable to get reg property.\n",
- dn->full_name);
- }
-
- eeh_save_bars(edev);
- return NULL;
-}
-
/**
* eeh_ops_register - Register platform dependent EEH operations
* @ops: platform dependent EEH operations
* Even if force-off is set, the EEH hardware is still enabled, so that
* newer systems can boot.
*/
-void __init eeh_init(void)
+static int __init eeh_init(void)
{
struct pci_controller *hose, *tmp;
struct device_node *phb;
if (!eeh_ops) {
pr_warning("%s: Platform EEH operation not found\n",
__func__);
- return;
+ return -EEXIST;
} else if ((ret = eeh_ops->init())) {
pr_warning("%s: Failed to call platform init function (%d)\n",
__func__, ret);
- return;
+ return ret;
}
raw_spin_lock_init(&confirm_error_lock);
/* Enable EEH for all adapters */
- list_for_each_entry_safe(hose, tmp, &hose_list, list_node) {
- phb = hose->dn;
- traverse_pci_devices(phb, eeh_early_enable, NULL);
+ if (eeh_probe_mode_devtree()) {
+ list_for_each_entry_safe(hose, tmp,
+ &hose_list, list_node) {
+ phb = hose->dn;
+ traverse_pci_devices(phb, eeh_ops->of_probe, NULL);
+ }
}
if (eeh_subsystem_enabled)
- printk(KERN_INFO "EEH: PCI Enhanced I/O Error Handling Enabled\n");
+ pr_info("EEH: PCI Enhanced I/O Error Handling Enabled\n");
else
- printk(KERN_WARNING "EEH: No capable adapters found\n");
+ pr_warning("EEH: No capable adapters found\n");
+
+ return ret;
}
+core_initcall_sync(eeh_init);
+
/**
* eeh_add_device_early - Enable EEH for the indicated device_node
* @dn: device node for which to set up EEH
if (NULL == phb || 0 == phb->buid)
return;
- eeh_early_enable(dn, NULL);
+ /* FIXME: hotplug support on POWERNV */
+ eeh_ops->of_probe(dn, NULL);
}
/**
edev->pdev = dev;
dev->dev.archdata.edev = edev;
- pci_addr_cache_insert_device(dev);
+ eeh_addr_cache_insert_dev(dev);
eeh_sysfs_add_device(dev);
}
dev->dev.archdata.edev = NULL;
pci_dev_put(dev);
- pci_addr_cache_remove_device(dev);
+ eeh_rmv_from_parent_pe(edev);
+ eeh_addr_cache_rmv_dev(dev);
eeh_sysfs_remove_device(dev);
}
projects / firefly-linux-kernel-4.4.55.git / blobdiff