insw(port, addr, count);
}
-static u32 ide_inl (unsigned long port)
-{
- return (u32) inl(port);
-}
-
static void ide_insl (unsigned long port, void *addr, u32 count)
{
insl(port, addr, count);
outsw(port, addr, count);
}
-static void ide_outl (u32 val, unsigned long port)
-{
- outl(val, port);
-}
-
static void ide_outsl (unsigned long port, void *addr, u32 count)
{
outsl(port, addr, count);
hwif->OUTB = ide_outb;
hwif->OUTBSYNC = ide_outbsync;
hwif->OUTW = ide_outw;
- hwif->OUTL = ide_outl;
hwif->OUTSW = ide_outsw;
hwif->OUTSL = ide_outsl;
hwif->INB = ide_inb;
hwif->INW = ide_inw;
- hwif->INL = ide_inl;
hwif->INSW = ide_insw;
hwif->INSL = ide_insl;
}
__ide_mm_insw((void __iomem *) port, addr, count);
}
-static u32 ide_mm_inl (unsigned long port)
-{
- return (u32) readl((void __iomem *) port);
-}
-
static void ide_mm_insl (unsigned long port, void *addr, u32 count)
{
__ide_mm_insl((void __iomem *) port, addr, count);
__ide_mm_outsw((void __iomem *) port, addr, count);
}
-static void ide_mm_outl (u32 value, unsigned long port)
-{
- writel(value, (void __iomem *) port);
-}
-
static void ide_mm_outsl (unsigned long port, void *addr, u32 count)
{
__ide_mm_outsl((void __iomem *) port, addr, count);
this one is controller specific! */
hwif->OUTBSYNC = ide_mm_outbsync;
hwif->OUTW = ide_mm_outw;
- hwif->OUTL = ide_mm_outl;
hwif->OUTSW = ide_mm_outsw;
hwif->OUTSL = ide_mm_outsl;
hwif->INB = ide_mm_inb;
hwif->INW = ide_mm_inw;
- hwif->INL = ide_mm_inl;
hwif->INSW = ide_mm_insw;
hwif->INSL = ide_mm_insl;
}
if(!(drive->id->hw_config & 0x4000))
return 0;
#endif /* CONFIG_IDEDMA_IVB */
+ /*
+ * FIXME:
+ * - change master/slave IDENTIFY order
+ * - force bit13 (80c cable present) check
+ * (unless the slave device is pre-ATA3)
+ */
return 1;
}
#ifdef CONFIG_BLK_DEV_IDEDMA
if (hwif->ide_dma_check) /* check if host supports DMA */
- hwif->ide_dma_host_off(drive);
+ hwif->dma_host_off(drive);
#endif
/*
#ifdef CONFIG_BLK_DEV_IDEDMA
if (speed >= XFER_SW_DMA_0)
- hwif->ide_dma_host_on(drive);
+ hwif->dma_host_on(drive);
else if (hwif->ide_dma_check) /* check if host supports DMA */
- hwif->ide_dma_off_quietly(drive);
+ hwif->dma_off_quietly(drive);
#endif
switch(speed) {
hwgroup->handler = handler;
hwgroup->expiry = expiry;
hwgroup->timer.expires = jiffies + timeout;
+ hwgroup->req_gen_timer = hwgroup->req_gen;
add_timer(&hwgroup->timer);
}
hwgroup->handler = handler;
hwgroup->expiry = expiry;
hwgroup->timer.expires = jiffies + timeout;
+ hwgroup->req_gen_timer = hwgroup->req_gen;
add_timer(&hwgroup->timer);
hwif->OUTBSYNC(drive, cmd, IDE_COMMAND_REG);
/* Drive takes 400nS to respond, we must avoid the IRQ being
}
/* done polling */
hwgroup->polling = 0;
+ hwgroup->resetting = 0;
return ide_stopped;
}
}
}
hwgroup->polling = 0; /* done polling */
+ hwgroup->resetting = 0; /* done reset attempt */
return ide_stopped;
}
{
#ifdef CONFIG_BLK_DEV_IDEDMA
if (drive->crc_count) {
- (void) HWIF(drive)->ide_dma_off_quietly(drive);
+ drive->hwif->dma_off_quietly(drive);
ide_set_xfer_rate(drive, ide_auto_reduce_xfer(drive));
if (drive->current_speed >= XFER_SW_DMA_0)
(void) HWIF(drive)->ide_dma_on(drive);
} else
- (void)__ide_dma_off(drive);
+ ide_dma_off(drive);
#endif
}
if (HWIF(drive)->pre_reset != NULL)
HWIF(drive)->pre_reset(drive);
+ if (drive->current_speed != 0xff)
+ drive->desired_speed = drive->current_speed;
+ drive->current_speed = 0xff;
}
/*
/* For an ATAPI device, first try an ATAPI SRST. */
if (drive->media != ide_disk && !do_not_try_atapi) {
+ hwgroup->resetting = 1;
pre_reset(drive);
SELECT_DRIVE(drive);
udelay (20);
return ide_stopped;
}
+ hwgroup->resetting = 1;
/*
* Note that we also set nIEN while resetting the device,
* to mask unwanted interrupts from the interface during the reset.