config TOUCHSCREEN_XPT2046_SPI
tristate "XPT2046 based touchscreens:SPI Interface"
depends on SPIM_RK29
-
+
config TOUCHSCREEN_XPT2046_NORMAL_SPI
tristate "normal mode"
depends on TOUCHSCREEN_XPT2046_SPI
-
- config TOUCHSCREEN_480X800
+
+ config TOUCHSCREEN_480X800
tristate "480X800 resolution"
depends on TOUCHSCREEN_XPT2046_NORMAL_SPI
-
+
config TOUCHSCREEN_800X480
tristate "800X480 resolution"
depends on TOUCHSCREEN_XPT2046_NORMAL_SPI
-
+
config TOUCHSCREEN_320X480
tristate "320X480 resolution"
depends on TOUCHSCREEN_XPT2046_NORMAL_SPI
-
+
config TOUCHSCREEN_XPT2046_TSLIB_SPI
tristate "tslib mode"
depends on TOUCHSCREEN_XPT2046_SPI
-
+
config TOUCHSCREEN_480X800
tristate "480X800 resolution"
depends on TOUCHSCREEN_XPT2046_TSLIB_SPI
-
+
config TOUCHSCREEN_800X480
tristate "800X480 resolution"
depends on TOUCHSCREEN_XPT2046_TSLIB_SPI
-
+
config TOUCHSCREEN_320X480
tristate "320X480 resolution"
depends on TOUCHSCREEN_XPT2046_TSLIB_SPI
-
+
config TOUCHSCREEN_XPT2046_CBN_SPI
tristate "calibration mode"
depends on TOUCHSCREEN_XPT2046_SPI
-
+
config TOUCHSCREEN_480X800
tristate "480X800 resolution"
depends on TOUCHSCREEN_XPT2046_CBN_SPI
-
+
config TOUCHSCREEN_800X480
tristate "800X480 resolution"
depends on TOUCHSCREEN_XPT2046_CBN_SPI
-
+
config TOUCHSCREEN_320X480
tristate "320X480 resolution"
depends on TOUCHSCREEN_XPT2046_CBN_SPI
+config TOUCHSCREEN_88PM860X
+ tristate "Marvell 88PM860x touchscreen"
+ depends on MFD_88PM860X
+ help
+ Say Y here if you have a 88PM860x PMIC and want to enable
+ support for the built-in touchscreen.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called 88pm860x-ts.
+
config TOUCHSCREEN_ADS7846
- tristate "ADS7846/TSC2046 and ADS7843 based touchscreens"
+ tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
depends on SPI_MASTER
depends on HWMON = n || HWMON
help
Say Y here if you have a touchscreen interface using the
- ADS7846/TSC2046 or ADS7843 controller, and your board-specific
- setup code includes that in its table of SPI devices.
+ ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
+ and your board-specific setup code includes that in its
+ table of SPI devices.
If HWMON is selected, and the driver is told the reference voltage
on your board, you will also get hwmon interfaces for the voltage
- (and on ads7846/tsc2046, temperature) sensors of this chip.
+ (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
If unsure, say N (but it's safe to say "Y").
To compile this driver as a module, choose M here: the
module will be called ad7877.
-
+
config TOUCHSCREEN_ILI2102_IIC
tristate "ili2102 based touchscreens: IIC Interface"
help
code includes that in its table of IIC devices.
If unsure, say N (but it's safe to say "Y").
+config TOUCHSCREEN_GT8XX
+ tristate "Goodix touch screen gt801X2 support for rockchip based platform"
+ help
+ Say Y here if you have a touchscreen interface using the
+ two goodix gt801 , and your board-specific initialization
+ code includes that in its table of IIC devices.
+ If unsure, say N.
+ config TOUCH_MAX_X
+ int "touch max x resolution"
+ depends on TOUCHSCREEN_GT8XX
+ default 1280
+ help
+ goodix touch max X resolution
+
+ config TOUCH_MAX_Y
+ int "touch max y resolution"
+ depends on TOUCHSCREEN_GT8XX
+ default 800
+ help
+ goodix touch max y resolution
config RK28_I2C_TS_NTP070
tristate "NTP070 based touchscreens: NTP070 Interface"
depends on I2C_RK2818
-
+
config TOUCHSCREEN_IT7250
tristate "IT7250 based touchscreens: IT7250 Interface"
help
If unsure, say N (but it's safe to say "Y").
-config TOUCHSCREEN_AD7879_I2C
- tristate "AD7879 based touchscreens: AD7879-1 I2C Interface"
- depends on I2C
- select TOUCHSCREEN_AD7879
+config TOUCHSCREEN_AD7879
+ tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
help
- Say Y here if you have a touchscreen interface using the
- AD7879-1/AD7889-1 controller, and your board-specific
- initialization code includes that in its table of I2C devices.
+ Say Y here if you want to support a touchscreen interface using
+ the AD7879-1/AD7889-1 controller.
- If unsure, say N (but it's safe to say "Y").
+ You should select a bus connection too.
To compile this driver as a module, choose M here: the
module will be called ad7879.
+config TOUCHSCREEN_AD7879_I2C
+ tristate "support I2C bus connection"
+ depends on TOUCHSCREEN_AD7879 && I2C
+ help
+ Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ad7879-i2c.
+
config TOUCHSCREEN_AD7879_SPI
- tristate "AD7879 based touchscreens: AD7879 SPI Interface"
- depends on SPI_MASTER && TOUCHSCREEN_AD7879_I2C = n
- select TOUCHSCREEN_AD7879
+ tristate "support SPI bus connection"
+ depends on TOUCHSCREEN_AD7879 && SPI_MASTER
help
- Say Y here if you have a touchscreen interface using the
- AD7879/AD7889 controller, and your board-specific initialization
- code includes that in its table of SPI devices.
+ Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
If unsure, say N (but it's safe to say "Y").
To compile this driver as a module, choose M here: the
- module will be called ad7879.
+ module will be called ad7879-spi.
-config TOUCHSCREEN_AD7879
- tristate
- default n
+config TOUCHSCREEN_ATMEL_MXT
+ tristate "Atmel mXT I2C Touchscreen"
+ depends on I2C
+ help
+ Say Y here if you have Atmel mXT series I2C touchscreen,
+ such as AT42QT602240/ATMXT224, connected to your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called atmel_mxt_ts.
config TOUCHSCREEN_BITSY
tristate "Compaq iPAQ H3600 (Bitsy) touchscreen"
To compile this driver as a module, choose M here: the
module will be called h3600_ts_input.
-config TOUCHSCREEN_CORGI
- tristate "SharpSL (Corgi and Spitz series) touchscreen driver (DEPRECATED)"
- depends on PXA_SHARPSL
- select CORGI_SSP_DEPRECATED
- default y
+config TOUCHSCREEN_BU21013
+ tristate "BU21013 based touch panel controllers"
+ depends on I2C
help
- Say Y here to enable the driver for the touchscreen on the
- Sharp SL-C7xx and SL-Cxx00 series of PDAs.
+ Say Y here if you have a bu21013 touchscreen connected to
+ your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
- module will be called corgi_ts.
+ module will be called bu21013_ts.
+
+config TOUCHSCREEN_CY8CTMG110
+ tristate "cy8ctmg110 touchscreen"
+ depends on I2C
+ depends on GPIOLIB
- NOTE: this driver is deprecated, try enable SPI and generic
- ADS7846-based touchscreen driver.
+ help
+ Say Y here if you have a cy8ctmg110 capacitive touchscreen on
+ an AAVA device.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called cy8ctmg110_ts.
config TOUCHSCREEN_DA9034
tristate "Touchscreen support for Dialog Semiconductor DA9034"
Say Y here to enable the support for the touchscreen found
on Dialog Semiconductor DA9034 PMIC.
+config TOUCHSCREEN_DYNAPRO
+ tristate "Dynapro serial touchscreen"
+ select SERIO
+ help
+ Say Y here if you have a Dynapro serial touchscreen connected to
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called dynapro.
+
+config TOUCHSCREEN_HAMPSHIRE
+ tristate "Hampshire serial touchscreen"
+ select SERIO
+ help
+ Say Y here if you have a Hampshire serial touchscreen connected to
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called hampshire.
+
config TOUCHSCREEN_EETI
tristate "EETI touchscreen panel support"
depends on I2C
To compile this driver as a module, choose M here: the
module will be called fujitsu-ts.
+config TOUCHSCREEN_S3C2410
+ tristate "Samsung S3C2410/generic touchscreen input driver"
+ depends on ARCH_S3C2410 || SAMSUNG_DEV_TS
+ select S3C_ADC
+ help
+ Say Y here if you have the s3c2410 touchscreen.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called s3c2410_ts.
+
config TOUCHSCREEN_GUNZE
tristate "Gunze AHL-51S touchscreen"
select SERIO
To compile this driver as a module, choose M here: the
module will be called wacom_w8001.
+config TOUCHSCREEN_LPC32XX
+ tristate "LPC32XX touchscreen controller"
+ depends on ARCH_LPC32XX
+ help
+ Say Y here if you have a LPC32XX device and want
+ to support the built-in touchscreen.
+
+ To compile this driver as a module, choose M here: the
+ module will be called lpc32xx_ts.
+
+config TOUCHSCREEN_MAX11801
+ tristate "MAX11801 based touchscreens"
+ depends on I2C
+ help
+ Say Y here if you have a MAX11801 based touchscreen
+ controller.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called max11801_ts.
+
config TOUCHSCREEN_MCS5000
tristate "MELFAS MCS-5000 touchscreen"
depends on I2C
To compile this driver as a module, choose M here: the
module will be called inexio.
+config TOUCHSCREEN_INTEL_MID
+ tristate "Intel MID platform resistive touchscreen"
+ depends on INTEL_SCU_IPC
+ help
+ Say Y here if you have a Intel MID based touchscreen in
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called intel_mid_touch.
+
config TOUCHSCREEN_MK712
tristate "ICS MicroClock MK712 touchscreen"
help
To compile this driver as a module, choose M here: the
module will be called migor_ts.
+config TOUCHSCREEN_TNETV107X
+ tristate "TI TNETV107X touchscreen support"
+ depends on ARCH_DAVINCI_TNETV107X
+ help
+ Say Y here if you want to use the TNETV107X touchscreen.
+
+ To compile this driver as a module, choose M here: the
+ module will be called tnetv107x-ts.
+
config TOUCHSCREEN_SYNAPTICS_I2C_RMI
tristate "Synaptics i2c touchscreen"
depends on I2C
config TOUCHSCREEN_ATMEL_TSADCC
tristate "Atmel Touchscreen Interface"
- depends on ARCH_AT91SAM9RL
+ depends on ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
help
Say Y here if you have a 4-wire touchscreen connected to the
ADC Controller on your Atmel SoC (such as the AT91SAM9RL).
To compile this driver as a module, choose M here: the
module will be called ucb1400_ts.
+config TOUCHSCREEN_WM831X
+ tristate "Support for WM831x touchscreen controllers"
+ depends on MFD_WM831X
+ help
+ This enables support for the touchscreen controller on the WM831x
+ series of PMICs.
+
+ To compile this driver as a module, choose M here: the
+ module will be called wm831x-ts.
+
config TOUCHSCREEN_WM97XX
tristate "Support for WM97xx AC97 touchscreen controllers"
depends on AC97_BUS
- IdealTEK URTC1000
- GoTop Super_Q2/GogoPen/PenPower tablets
- JASTEC USB Touch Controller/DigiTech DTR-02U
+ - Zytronic controllers
Have a look at <http://linux.chapter7.ch/touchkit/> for
a usage description and the required user-space stuff.
To compile this driver as a module, choose M here: the
module will be called usbtouchscreen.
+config TOUCHSCREEN_MC13783
+ tristate "Freescale MC13783 touchscreen input driver"
+ depends on MFD_MC13783
+ help
+ Say Y here if you have an Freescale MC13783 PMIC on your
+ board and want to use its touchscreen
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called mc13783_ts.
+
config TOUCHSCREEN_USB_EGALAX
default y
- bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED
+ bool "eGalax, eTurboTouch CT-410/510/700 device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_PANJIT
default y
- bool "PanJit device support" if EMBEDDED
+ bool "PanJit device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_3M
default y
- bool "3M/Microtouch EX II series device support" if EMBEDDED
+ bool "3M/Microtouch EX II series device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_ITM
default y
- bool "ITM device support" if EMBEDDED
+ bool "ITM device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_ETURBO
default y
- bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED
+ bool "eTurboTouch (non-eGalax compatible) device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_GUNZE
default y
- bool "Gunze AHL61 device support" if EMBEDDED
+ bool "Gunze AHL61 device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_DMC_TSC10
default y
- bool "DMC TSC-10/25 device support" if EMBEDDED
+ bool "DMC TSC-10/25 device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_IRTOUCH
default y
- bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED
+ bool "IRTOUCHSYSTEMS/UNITOP device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_IDEALTEK
default y
- bool "IdealTEK URTC1000 device support" if EMBEDDED
+ bool "IdealTEK URTC1000 device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_GENERAL_TOUCH
default y
- bool "GeneralTouch Touchscreen device support" if EMBEDDED
+ bool "GeneralTouch Touchscreen device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_GOTOP
default y
- bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED
+ bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_JASTEC
default y
- bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EMBEDDED
+ bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_E2I
bool "e2i Touchscreen controller (e.g. from Mimo 740)"
depends on TOUCHSCREEN_USB_COMPOSITE
+config TOUCHSCREEN_USB_ZYTRONIC
+ default y
+ bool "Zytronic controller" if EXPERT
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_ETT_TC45USB
+ default y
+ bool "ET&T USB series TC4UM/TC5UH touchscreen controller support" if EXPERT
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_NEXIO
+ default y
+ bool "NEXIO/iNexio device support" if EXPERT
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
config TOUCHSCREEN_TOUCHIT213
tristate "Sahara TouchIT-213 touchscreen"
select SERIO
To compile this driver as a module, choose M here: the
module will be called touchit213.
+config TOUCHSCREEN_TSC2005
+ tristate "TSC2005 based touchscreens"
+ depends on SPI_MASTER && GENERIC_HARDIRQS
+ help
+ Say Y here if you have a TSC2005 based touchscreen.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called tsc2005.
+
config TOUCHSCREEN_TSC2007
tristate "TSC2007 based touchscreens"
depends on I2C
To compile this driver as a module, choose M here: the
module will be called pcap_ts.
+config TOUCHSCREEN_ST1232
+ tristate "Sitronix ST1232 touchscreen controllers"
+ depends on I2C
+ help
+ Say Y here if you want to support Sitronix ST1232
+ touchscreen controller.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called st1232_ts.
+
+config TOUCHSCREEN_STMPE
+ tristate "STMicroelectronics STMPE touchscreens"
+ depends on MFD_STMPE
+ help
+ Say Y here if you want support for STMicroelectronics
+ STMPE touchscreen controllers.
+
+ To compile this driver as a module, choose M here: the
+ module will be called stmpe-ts.
+
+config TOUCHSCREEN_TPS6507X
+ tristate "TPS6507x based touchscreens"
+ depends on I2C
+ help
+ Say Y here if you have a TPS6507x based touchscreen
+ controller.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called tps6507x_ts.
+
config HANNSTAR_P1003
tristate "Hannstar P1003 touchscreen"
depends on I2C2_RK29
int "hannstar touch x max"
depends on HANNSTAR_P1003
default 1087
- help
+ help
RK29 hannstar touch max X size
config HANNSTAR_MAX_Y
RK29 hannstar touch max Y size
config HANNSTAR_DEBUG
- bool "hannstar debug"
- depends on HANNSTAR_P1003
+ bool "hannstar debug"
+ depends on HANNSTAR_P1003
default n
help
- RK29 hannstar touch debug
+ RK29 hannstar touch debug
+
config ATMEL_MXT224
tristate "Atmel mXT224 touchscreen"
depends on I2C2_RK29
RK29 atmel_mxt224 touch max Y size
config SINTEK_3FA16
- tristate "Sintek 3FA16 touchscreen"
+ tristate "Sintek 3FA16 touchscreen"
depends on I2C2_RK29
help
RK29 Sintek touch
help
RK29 hannstar touch max Y size
-
config HANNSTAR_DEBUG
bool "Sintek debug"
depends on SINTEK_3FA16
default n
help
RK29 hannstar touch debug
+
config EETI_EGALAX
tristate "EETI_EGALAX touchscreen panel support"
depends on I2C
To compile this driver as a module, choose M here: the
module will be called eeti_egalax_ts.
-
+
config EETI_EGALAX_MAX_X
int "EETI_EGALAX_MAX_X"
depends on EETI_EGALAX
If unsure, say N (but it's safe to say "Y").
+config TOUCHSCREEN_IT7260_I2C
+ tristate "IT7260 based touchscreens: IT7260 I2C Interface"
+ depends on I2C_RK29
+ help
+ Say Y here if you have a touchscreen interface using the
+ IT7260 controller, and your board-specific initialization
+ code includes that in its table of I2C devices.
+
+ If unsure, say N (but it's safe to say "Y").
+
+config TOUCHSCREEN_NAS
+ tristate "NAS based touchscreens: NAS Interface"
+ depends on I2C2_RK29
+ help
+ Say Y here if you have a touchscreen interface using the
+ nas controller, and your board-specific initialization
+ code includes that in its table of I2C devices.
+
+ If unsure, say N (but it's safe to say "Y").
+
+config LAIBAO_TS
+ tristate "LAIBAO touchscreen"
+ depends on I2C2_RK29
+ help
+ RK29 LAIBAO touchscreen
+
config TOUCHSCREEN_GT801_IIC
tristate "GT801_IIC based touchscreens"
depends on I2C2_RK29
+
config TOUCHSCREEN_GT818_IIC
tristate "GT818_IIC based touchscreens"
depends on I2C2_RK29
+
+config TOUCHSCREEN_PIXCIR
+ tristate "PIXCIR_IIC based touchscreens"
+ depends on I2C2_RK29
+
+config TOUCHSCREEN_SYNAPTICS_RMI4_I2C_RK
+ tristate "Synaptics i2c rmi4 touchscreen"
+ depends on I2C2_RK30
+ help
+ This enables support for Synaptics RMI over I2C based touchscreens.
+ config TOUCHSCREEN_SYNAPTICS_S3202
+ tristate "SYNAPTICS S3202 touchscreen"
+ depends on TOUCHSCREEN_SYNAPTICS_RMI4_I2C_RK
+
config D70_L3188A
tristate "D70-L3188A based touchscreens"
depends on I2C2_RK29
+
config TOUCHSCREEN_GT819
tristate "GT819 based touchscreens"
depends on I2C2_RK29
+
+config TOUCHSCREEN_FT5306
+ tristate "FT5306 based touchscreens: FT5306 Interface"
+ depends on I2C2_RK29 || I2C2_RK30
+
config TOUCHSCREEN_FT5406
tristate "FT5406 based touchscreens: FT5406 Interface"
depends on I2C2_RK29
help
say Y here if you have a touchscreen interface using the FT5406
- controller,and your board-specific initialization code includes that
+ controller,and your board-specific initialization code includes that
in its table of I2C devices.
-
+
If unsure, say N(but it's safe to say "Y").
+
+config ATMEL_MXT1386
+ tristate "ATMEL_MXT1386 touchscreen panel support"
+ depends on I2C
+ help
+ Say Y here to enable support for I2C connected ATMEL_MXT1386 touch panels.
+
+ To compile this driver as a module, choose M here: the
+ module will be called atmel_mxt1386_ts.
+
+ config ATMEL_MXT1386_MAX_X
+ int "ATMEL_MXT1386_MAX_X"
+ depends on ATMEL_MXT1386
+ default 4095
+ help
+ RK29 ATMEL_MXT1386 touch max X size
+
+ config ATMEL_MXT1386_MAX_Y
+ int "ATMEL_MXT1386_MAX_Y"
+ depends on ATMEL_MXT1386
+ default 4095
+ help
+ RK29 ATMEL_MXT1386 touch max Y size
+
+ config ATMEL_MXT1386_DEBUG
+ bool "ATMEL_MXT1386 debug"
+ depends on ATMEL_MXT1386
+ default n
+ help
+ RK29 ATMEL_MXT1386 touch debug
endif