#include "dvb_frontend.h"
#include "dvb-bt8xx.h"
#include "bt878.h"
+#include "dvb-pll.h"
static int debug;
data[0] = (div >> 8) & 0x7f;
data[1] = div & 0xff;
data[2] = ((div >> 10) & 0x60) | cfg;
- data[3] = cpump | band_select;
+ data[3] = (cpump << 6) | band_select;
i2c_transfer(card->i2c_adapter, &msg, 1);
return (div * 166666 - 36000000);
/*
* Reset the frontend, must be called before trying
* to initialise the MT352 or mt352_attach
- * will fail.
- *
- * Presumably not required for the NXT6000 frontend.
+ * will fail. Same goes for the nxt6000 frontend.
*
*/
.pll_set = digitv_alps_tded4_pll_set,
};
+static int tdvs_tua6034_pll_set(struct dvb_frontend* fe, struct dvb_frontend_parameters* params)
+{
+ struct dvb_bt8xx_card *card = (struct dvb_bt8xx_card *) fe->dvb->priv;
+ u8 buf[4];
+ struct i2c_msg msg = { .addr = 0x61, .flags = 0, .buf = buf, .len = sizeof(buf) };
+ int err;
+
+ dvb_pll_configure(&dvb_pll_tdvs_tua6034, buf, params->frequency, 0);
+ dprintk("%s: tuner at 0x%02x bytes: 0x%02x 0x%02x 0x%02x 0x%02x\n",
+ __FUNCTION__, msg.addr, buf[0],buf[1],buf[2],buf[3]);
+ if ((err = i2c_transfer(card->i2c_adapter, &msg, 1)) != 1) {
+ printk(KERN_WARNING "dvb-bt8xx: %s error "
+ "(addr %02x <- %02x, err = %i)\n",
+ __FUNCTION__, buf[0], buf[1], err);
+ if (err < 0)
+ return err;
+ else
+ return -EREMOTEIO;
+ }
+
+ /* Set the Auxiliary Byte. */
+ buf[2] &= ~0x20;
+ buf[2] |= 0x18;
+ buf[3] = 0x50;
+ i2c_transfer(card->i2c_adapter, &msg, 1);
+
+ return 0;
+}
+
+static struct lgdt330x_config tdvs_tua6034_config = {
+ .demod_address = 0x0e,
+ .demod_chip = LGDT3303,
+ .serial_mpeg = 0x40, /* TPSERIAL for 3303 in TOP_CONTROL */
+ .pll_set = tdvs_tua6034_pll_set,
+};
+
+static void lgdt330x_reset(struct dvb_bt8xx_card *bt)
+{
+ /* Set pin 27 of the lgdt3303 chip high to reset the frontend */
+
+ /* Pulse the reset line */
+ bttv_write_gpio(bt->bttv_nr, 0x00e00007, 0x00000001); /* High */
+ bttv_write_gpio(bt->bttv_nr, 0x00e00007, 0x00000000); /* Low */
+ msleep(100);
+
+ bttv_write_gpio(bt->bttv_nr, 0x00e00007, 0x00000001); /* High */
+ msleep(100);
+}
+
static void frontend_init(struct dvb_bt8xx_card *card, u32 type)
{
int ret;
struct dst_state* state = NULL;
switch(type) {
-#ifdef BTTV_DVICO_DVBT_LITE
- case BTTV_DVICO_DVBT_LITE:
+ case BTTV_BOARD_DVICO_DVBT_LITE:
card->fe = mt352_attach(&thomson_dtt7579_config, card->i2c_adapter);
if (card->fe != NULL) {
card->fe->ops->info.frequency_min = 174000000;
card->fe->ops->info.frequency_max = 862000000;
}
break;
-#endif
-#ifdef BTTV_TWINHAN_VP3021
- case BTTV_TWINHAN_VP3021:
+ case BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE:
+ lgdt330x_reset(card);
+ card->fe = lgdt330x_attach(&tdvs_tua6034_config, card->i2c_adapter);
+ if (card->fe != NULL)
+ dprintk ("dvb_bt8xx: lgdt330x detected\n");
+ break;
+
+#ifdef BTTV_BOARD_TWINHAN_VP3021
+ case BTTV_BOARD_TWINHAN_VP3021:
#else
- case BTTV_NEBULA_DIGITV:
+ case BTTV_BOARD_NEBULA_DIGITV:
#endif
/*
* It is possible to determine the correct frontend using the I2C bus (see the Nebula SDK);
*/
/* Old Nebula (marked (c)2003 on high profile pci card) has nxt6000 demod */
+ digitv_alps_tded4_reset(card);
card->fe = nxt6000_attach(&vp3021_alps_tded4_config, card->i2c_adapter);
if (card->fe != NULL) {
dprintk ("dvb_bt8xx: an nxt6000 was detected on your digitv card\n");
dprintk ("dvb_bt8xx: an mt352 was detected on your digitv card\n");
break;
- case BTTV_AVDVBT_761:
+ case BTTV_BOARD_AVDVBT_761:
card->fe = sp887x_attach(µtune_mt7202dtf_config, card->i2c_adapter);
break;
- case BTTV_AVDVBT_771:
+ case BTTV_BOARD_AVDVBT_771:
card->fe = mt352_attach(&advbt771_samsung_tdtc9251dh0_config, card->i2c_adapter);
if (card->fe != NULL) {
card->fe->ops->info.frequency_min = 174000000;
}
break;
- case BTTV_TWINHAN_DST:
+ case BTTV_BOARD_TWINHAN_DST:
/* DST is not a frontend driver !!! */
state = (struct dst_state *) kmalloc(sizeof (struct dst_state), GFP_KERNEL);
/* Setup the Card */
ret = dst_ca_attach(state, &card->dvb_adapter);
break;
- case BTTV_PINNACLESAT:
+ case BTTV_BOARD_PINNACLESAT:
card->fe = cx24110_attach(&pctvsat_config, card->i2c_adapter);
break;
- case BTTV_PC_HDTV:
+ case BTTV_BOARD_PC_HDTV:
card->fe = or51211_attach(&or51211_config, card->i2c_adapter);
break;
}
card->i2c_adapter = &sub->core->i2c_adap;
switch(sub->core->type) {
- case BTTV_PINNACLESAT:
+ case BTTV_BOARD_PINNACLESAT:
card->gpio_mode = 0x0400c060;
/* should be: BT878_A_GAIN=0,BT878_A_PWRDN,BT878_DA_DPM,BT878_DA_SBR,
BT878_DA_IOM=1,BT878_DA_APP to enable serial highspeed mode. */
card->irq_err_ignore = 0;
break;
-#ifdef BTTV_DVICO_DVBT_LITE
- case BTTV_DVICO_DVBT_LITE:
-#endif
+ case BTTV_BOARD_DVICO_DVBT_LITE:
card->gpio_mode = 0x0400C060;
card->op_sync_orin = 0;
card->irq_err_ignore = 0;
* DA_APP(parallel) */
break;
-#ifdef BTTV_TWINHAN_VP3021
- case BTTV_TWINHAN_VP3021:
+ case BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE:
+ card->gpio_mode = 0x0400c060;
+ card->op_sync_orin = BT878_RISC_SYNC_MASK;
+ card->irq_err_ignore = BT878_AFBUS | BT878_AFDSR;
+ break;
+
+#ifdef BTTV_BOARD_TWINHAN_VP3021
+ case BTTV_BOARD_TWINHAN_VP3021:
#else
- case BTTV_NEBULA_DIGITV:
+ case BTTV_BOARD_NEBULA_DIGITV:
#endif
- case BTTV_AVDVBT_761:
+ case BTTV_BOARD_AVDVBT_761:
card->gpio_mode = (1 << 26) | (1 << 14) | (1 << 5);
card->op_sync_orin = 0;
card->irq_err_ignore = 0;
/* A_PWRDN DA_SBR DA_APP (high speed serial) */
break;
- case BTTV_AVDVBT_771: //case 0x07711461:
+ case BTTV_BOARD_AVDVBT_771: //case 0x07711461:
card->gpio_mode = 0x0400402B;
card->op_sync_orin = BT878_RISC_SYNC_MASK;
card->irq_err_ignore = 0;
/* A_PWRDN DA_SBR DA_APP[0] PKTP=10 RISC_ENABLE FIFO_ENABLE*/
break;
- case BTTV_TWINHAN_DST:
+ case BTTV_BOARD_TWINHAN_DST:
card->gpio_mode = 0x2204f2c;
card->op_sync_orin = BT878_RISC_SYNC_MASK;
card->irq_err_ignore = BT878_APABORT | BT878_ARIPERR |
* RISC+FIFO ENABLE */
break;
- case BTTV_PC_HDTV:
+ case BTTV_BOARD_PC_HDTV:
card->gpio_mode = 0x0100EC7B;
card->op_sync_orin = 0;
card->irq_err_ignore = 0;
projects / firefly-linux-kernel-4.4.55.git / blobdiff