/* bnx2x_reg.h: Broadcom Everest network driver.
*
- * Copyright (c) 2007-2012 Broadcom Corporation
+ * Copyright (c) 2007-2013 Broadcom Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
/* [RW 28] The value sent to CM header in the case of CFC load error. */
#define DORQ_REG_ERR_CMHEAD 0x170058
#define DORQ_REG_IF_EN 0x170004
+#define DORQ_REG_MAX_RVFID_SIZE 0x1701ec
#define DORQ_REG_MODE_ACT 0x170008
/* [RW 5] The normal mode CID extraction offset. */
#define DORQ_REG_NORM_CID_OFST 0x17002c
writes the same initial credit to the rspa_crd_cnt and rspb_crd_cnt. The
read reads this written value. */
#define DORQ_REG_RSP_INIT_CRD 0x170048
+#define DORQ_REG_RSPB_CRD_CNT 0x1700b0
+#define DORQ_REG_VF_NORM_CID_BASE 0x1701a0
+#define DORQ_REG_VF_NORM_CID_OFST 0x1701f4
+#define DORQ_REG_VF_NORM_CID_WND_SIZE 0x1701a4
+#define DORQ_REG_VF_NORM_MAX_CID_COUNT 0x1701e4
+#define DORQ_REG_VF_NORM_VF_BASE 0x1701a8
+/* [RW 10] VF type validation mask value */
+#define DORQ_REG_VF_TYPE_MASK_0 0x170218
+/* [RW 17] VF type validation Min MCID value */
+#define DORQ_REG_VF_TYPE_MAX_MCID_0 0x1702d8
+/* [RW 17] VF type validation Max MCID value */
+#define DORQ_REG_VF_TYPE_MIN_MCID_0 0x170298
+/* [RW 10] VF type validation comp value */
+#define DORQ_REG_VF_TYPE_VALUE_0 0x170258
+#define DORQ_REG_VF_USAGE_CT_LIMIT 0x170340
+
/* [RW 4] Initial activity counter value on the load request; when the
shortcut is done. */
#define DORQ_REG_SHRT_ACT_CNT 0x170070
#define HC_CONFIG_0_REG_MSI_MSIX_INT_EN_0 (0x1<<2)
#define HC_CONFIG_0_REG_SINGLE_ISR_EN_0 (0x1<<1)
#define HC_CONFIG_1_REG_BLOCK_DISABLE_1 (0x1<<0)
+#define DORQ_REG_VF_USAGE_CNT 0x170320
#define HC_REG_AGG_INT_0 0x108050
#define HC_REG_AGG_INT_1 0x108054
#define HC_REG_ATTN_BIT 0x108120
/* [R 4] This field indicates the type of the device. '0' - 2 Ports; '1' - 1
Port. */
#define MISC_REG_BOND_ID 0xa400
-/* [R 8] These bits indicate the metal revision of the chip. This value
- starts at 0x00 for each all-layer tape-out and increments by one for each
- tape-out. */
-#define MISC_REG_CHIP_METAL 0xa404
/* [R 16] These bits indicate the part number for the chip. */
#define MISC_REG_CHIP_NUM 0xa408
/* [R 4] These bits indicate the base revision of the chip. This value
/* [R 32] Interrupt register #0 read */
#define NIG_REG_NIG_INT_STS_0 0x103b0
#define NIG_REG_NIG_INT_STS_1 0x103c0
+/* [RC 32] Interrupt register #0 read clear */
+#define NIG_REG_NIG_INT_STS_CLR_0 0x103b4
/* [R 32] Legacy E1 and E1H location for parity error mask register. */
#define NIG_REG_NIG_PRTY_MASK 0x103dc
/* [RW 32] Parity mask register #0 read/write */
current task in process). */
#define PBF_REG_DISABLE_NEW_TASK_PROC_P4 0x14006c
#define PBF_REG_DISABLE_PF 0x1402e8
+#define PBF_REG_DISABLE_VF 0x1402ec
/* [RW 18] For port 0: For each client that is subject to WFQ (the
* corresponding bit is 1); indicates to which of the credit registers this
* client is mapped. For clients which are not credit blocked; their mapping
#define PXP_REG_HST_DISCARD_INTERNAL_WRITES_STATUS 0x10309c
/* [WB 160] Used for initialization of the inbound interrupts memory */
#define PXP_REG_HST_INBOUND_INT 0x103800
+/* [RW 7] Indirect access to the permission table. The fields are : {Valid;
+ * VFID[5:0]}
+ */
+#define PXP_REG_HST_ZONE_PERMISSION_TABLE 0x103400
/* [RW 32] Interrupt mask register #0 read/write */
#define PXP_REG_PXP_INT_MASK_0 0x103074
#define PXP_REG_PXP_INT_MASK_1 0x103084
#define HW_LOCK_RESOURCE_SPIO 2
#define AEU_INPUTS_ATTN_BITS_ATC_HW_INTERRUPT (0x1<<4)
#define AEU_INPUTS_ATTN_BITS_ATC_PARITY_ERROR (0x1<<5)
+#define AEU_INPUTS_ATTN_BITS_BRB_HW_INTERRUPT (0x1<<19)
#define AEU_INPUTS_ATTN_BITS_BRB_PARITY_ERROR (0x1<<18)
#define AEU_INPUTS_ATTN_BITS_CCM_HW_INTERRUPT (0x1<<31)
#define AEU_INPUTS_ATTN_BITS_CCM_PARITY_ERROR (0x1<<30)
#define PCI_PM_DATA_B 0x414
#define PCI_ID_VAL1 0x434
#define PCI_ID_VAL2 0x438
+#define PCI_ID_VAL3 0x43c
+
+#define GRC_CONFIG_REG_PF_INIT_VF 0x624
+#define GRC_CR_PF_INIT_VF_PF_FIRST_VF_NUM_MASK 0xf
+/* First VF_NUM for PF is encoded in this register.
+ * The number of VFs assigned to a PF is assumed to be a multiple of 8.
+ * Software should program these bits based on Total Number of VFs \
+ * programmed for each PF.
+ * Since registers from 0x000-0x7ff are split across functions, each PF will
+ * have the same location for the same 4 bits
+ */
#define PXPCS_TL_CONTROL_5 0x814
#define PXPCS_TL_CONTROL_5_UNKNOWNTYPE_ERR_ATTN (1 << 29) /*WC*/
(7L<<ME_REG_ABS_PF_NUM_SHIFT) /* Absolute PF Num */
+#define PXP_VF_ADDR_IGU_START 0
+#define PXP_VF_ADDR_IGU_SIZE 0x3000
+#define PXP_VF_ADDR_IGU_END\
+ ((PXP_VF_ADDR_IGU_START) + (PXP_VF_ADDR_IGU_SIZE) - 1)
+
+#define PXP_VF_ADDR_USDM_QUEUES_START 0x3000
+#define PXP_VF_ADDR_USDM_QUEUES_SIZE\
+ (PXP_VF_ADRR_NUM_QUEUES * PXP_ADDR_QUEUE_SIZE)
+#define PXP_VF_ADDR_USDM_QUEUES_END\
+ ((PXP_VF_ADDR_USDM_QUEUES_START) + (PXP_VF_ADDR_USDM_QUEUES_SIZE) - 1)
+
+#define PXP_VF_ADDR_CSDM_GLOBAL_START 0x7600
+#define PXP_VF_ADDR_CSDM_GLOBAL_SIZE (PXP_ADDR_REG_SIZE)
+#define PXP_VF_ADDR_CSDM_GLOBAL_END\
+ ((PXP_VF_ADDR_CSDM_GLOBAL_START) + (PXP_VF_ADDR_CSDM_GLOBAL_SIZE) - 1)
+
+#define PXP_VF_ADDR_DB_START 0x7c00
+#define PXP_VF_ADDR_DB_SIZE 0x200
+#define PXP_VF_ADDR_DB_END\
+ ((PXP_VF_ADDR_DB_START) + (PXP_VF_ADDR_DB_SIZE) - 1)
+
#define MDIO_REG_BANK_CL73_IEEEB0 0x0
#define MDIO_CL73_IEEEB0_CL73_AN_CONTROL 0x0
#define MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN 0x0200
projects / firefly-linux-kernel-4.4.55.git / blobdiff