/*******************************************************************************
Intel PRO/1000 Linux driver
- Copyright(c) 1999 - 2012 Intel Corporation.
+ Copyright(c) 1999 - 2013 Intel Corporation.
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
#ifndef _E1000_DEFINES_H_
#define _E1000_DEFINES_H_
-#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
-#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
-#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
-#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
-#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */
-#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
-#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */
-#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
-#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */
-#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */
-#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
-#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */
-#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */
-#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */
-#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */
-#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */
-#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */
-#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */
-
/* Number of Transmit and Receive Descriptors must be a multiple of 8 */
#define REQ_TX_DESCRIPTOR_MULTIPLE 8
#define REQ_RX_DESCRIPTOR_MULTIPLE 8
#define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000
#define E1000_CTRL_EXT_EIAME 0x01000000
#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */
-#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */
-#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */
+#define E1000_CTRL_EXT_IAME 0x08000000 /* Int ACK Auto-mask */
#define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */
#define E1000_CTRL_EXT_LSECCK 0x00001000
#define E1000_CTRL_EXT_PHYPDEN 0x00100000
#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */
#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */
+#define E1000_RXDEXT_STATERR_TST 0x00000100 /* Time Stamp taken */
#define E1000_RXDEXT_STATERR_CE 0x01000000
#define E1000_RXDEXT_STATERR_SE 0x02000000
#define E1000_RXDEXT_STATERR_SEQ 0x04000000
/* mask to determine if packets should be dropped due to frame errors */
#define E1000_RXD_ERR_FRAME_ERR_MASK ( \
- E1000_RXD_ERR_CE | \
- E1000_RXD_ERR_SE | \
- E1000_RXD_ERR_SEQ | \
- E1000_RXD_ERR_CXE | \
- E1000_RXD_ERR_RXE)
+ E1000_RXD_ERR_CE | \
+ E1000_RXD_ERR_SE | \
+ E1000_RXD_ERR_SEQ | \
+ E1000_RXD_ERR_CXE | \
+ E1000_RXD_ERR_RXE)
/* Same mask, but for extended and packet split descriptors */
#define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
- E1000_RXDEXT_STATERR_CE | \
- E1000_RXDEXT_STATERR_SE | \
- E1000_RXDEXT_STATERR_SEQ | \
- E1000_RXDEXT_STATERR_CXE | \
- E1000_RXDEXT_STATERR_RXE)
+ E1000_RXDEXT_STATERR_CE | \
+ E1000_RXDEXT_STATERR_SE | \
+ E1000_RXDEXT_STATERR_SEQ | \
+ E1000_RXDEXT_STATERR_CXE | \
+ E1000_RXDEXT_STATERR_RXE)
#define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000
#define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000
#define E1000_CTRL_MEHE 0x00080000 /* Memory Error Handling Enable */
#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
+#define E1000_CTRL_ADVD3WUC 0x00100000 /* D3 WUC */
+#define E1000_CTRL_EN_PHY_PWR_MGMT 0x00200000 /* PHY PM enable */
#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
#define E1000_CTRL_RST 0x04000000 /* Global reset */
#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
-/* Bit definitions for the Management Data IO (MDIO) and Management Data
- * Clock (MDC) pins in the Device Control Register.
- */
+#define E1000_PCS_LCTL_FORCE_FCTRL 0x80
+
+#define E1000_PCS_LSTS_AN_COMPLETE 0x10000
/* Device Status */
#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
#define E1000_STATUS_FUNC_SHIFT 2
#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
+#define E1000_STATUS_SPEED_MASK 0x000000C0
#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */
#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion by NVM */
#define E1000_STATUS_PHYRA 0x00000400 /* PHY Reset Asserted */
-#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
-
-/* Constants used to interpret the masked PCI-X bus speed. */
+#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Master Req status */
#define HALF_DUPLEX 1
#define FULL_DUPLEX 2
-
#define ADVERTISE_10_HALF 0x0001
#define ADVERTISE_10_FULL 0x0002
#define ADVERTISE_100_HALF 0x0004
#define ADVERTISE_1000_FULL 0x0020
/* 1000/H is not supported, nor spec-compliant. */
-#define E1000_ALL_SPEED_DUPLEX ( ADVERTISE_10_HALF | ADVERTISE_10_FULL | \
- ADVERTISE_100_HALF | ADVERTISE_100_FULL | \
- ADVERTISE_1000_FULL)
-#define E1000_ALL_NOT_GIG ( ADVERTISE_10_HALF | ADVERTISE_10_FULL | \
- ADVERTISE_100_HALF | ADVERTISE_100_FULL)
-#define E1000_ALL_100_SPEED (ADVERTISE_100_HALF | ADVERTISE_100_FULL)
-#define E1000_ALL_10_SPEED (ADVERTISE_10_HALF | ADVERTISE_10_FULL)
-#define E1000_ALL_HALF_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_100_HALF)
+#define E1000_ALL_SPEED_DUPLEX ( \
+ ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \
+ ADVERTISE_100_FULL | ADVERTISE_1000_FULL)
+#define E1000_ALL_NOT_GIG ( \
+ ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \
+ ADVERTISE_100_FULL)
+#define E1000_ALL_100_SPEED (ADVERTISE_100_HALF | ADVERTISE_100_FULL)
+#define E1000_ALL_10_SPEED (ADVERTISE_10_HALF | ADVERTISE_10_FULL)
+#define E1000_ALL_HALF_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_100_HALF)
#define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX
#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */
#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */
#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */
+#define E1000_TXD_EXTCMD_TSTAMP 0x00000010 /* IEEE1588 Timestamp packet */
/* Transmit Control */
#define E1000_TCTL_EN 0x00000002 /* enable Tx */
#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */
-/* Transmit Arbitration Count */
-
/* SerDes Control */
#define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400
+#define E1000_SCTL_ENABLE_SERDES_LOOPBACK 0x0410
/* Receive Checksum Control */
#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
#define E1000_KABGTXD_BGSQLBIAS 0x00050000
+/* Low Power IDLE Control */
+#define E1000_LPIC_LPIET_SHIFT 24 /* Low Power Idle Entry Time */
+
/* PBA constants */
#define E1000_PBA_8K 0x0008 /* 8KB */
#define E1000_PBA_16K 0x0010 /* 16KB */
+#define E1000_PBA_RXA_MASK 0xFFFF
+
#define E1000_PBS_16K E1000_PBA_16K
/* Uncorrectable/correctable ECC Error counts and enable bits */
#define E1000_ICR_RXDMT0 0x00000010 /* Rx desc min. threshold (0) */
#define E1000_ICR_RXT0 0x00000080 /* Rx timer intr (ring 0) */
#define E1000_ICR_ECCER 0x00400000 /* Uncorrectable ECC Error */
-#define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver should claim the interrupt */
+/* If this bit asserted, the driver should claim the interrupt */
+#define E1000_ICR_INT_ASSERTED 0x80000000
#define E1000_ICR_RXQ0 0x00100000 /* Rx Queue 0 Interrupt */
#define E1000_ICR_RXQ1 0x00200000 /* Rx Queue 1 Interrupt */
#define E1000_ICR_TXQ0 0x00400000 /* Tx Queue 0 Interrupt */
* o LSC = Link Status Change
*/
#define IMS_ENABLE_MASK ( \
- E1000_IMS_RXT0 | \
- E1000_IMS_TXDW | \
- E1000_IMS_RXDMT0 | \
- E1000_IMS_RXSEQ | \
- E1000_IMS_LSC)
+ E1000_IMS_RXT0 | \
+ E1000_IMS_TXDW | \
+ E1000_IMS_RXDMT0 | \
+ E1000_IMS_RXSEQ | \
+ E1000_IMS_LSC)
/* Interrupt Mask Set */
#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
#define E1000_RXCW_C 0x20000000 /* Receive config */
#define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */
+#define E1000_TSYNCTXCTL_VALID 0x00000001 /* Tx timestamp valid */
+#define E1000_TSYNCTXCTL_ENABLED 0x00000010 /* enable Tx timestamping */
+
+#define E1000_TSYNCRXCTL_VALID 0x00000001 /* Rx timestamp valid */
+#define E1000_TSYNCRXCTL_TYPE_MASK 0x0000000E /* Rx type mask */
+#define E1000_TSYNCRXCTL_TYPE_L2_V2 0x00
+#define E1000_TSYNCRXCTL_TYPE_L4_V1 0x02
+#define E1000_TSYNCRXCTL_TYPE_L2_L4_V2 0x04
+#define E1000_TSYNCRXCTL_TYPE_ALL 0x08
+#define E1000_TSYNCRXCTL_TYPE_EVENT_V2 0x0A
+#define E1000_TSYNCRXCTL_ENABLED 0x00000010 /* enable Rx timestamping */
+#define E1000_TSYNCRXCTL_SYSCFI 0x00000020 /* Sys clock frequency */
+
+#define E1000_RXMTRL_PTP_V1_SYNC_MESSAGE 0x00000000
+#define E1000_RXMTRL_PTP_V1_DELAY_REQ_MESSAGE 0x00010000
+
+#define E1000_RXMTRL_PTP_V2_SYNC_MESSAGE 0x00000000
+#define E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE 0x01000000
+
+#define E1000_TIMINCA_INCPERIOD_SHIFT 24
+#define E1000_TIMINCA_INCVALUE_MASK 0x00FFFFFF
+
/* PCI Express Control */
#define E1000_GCR_RXD_NO_SNOOP 0x00000001
#define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002
E1000_GCR_TXDSCW_NO_SNOOP | \
E1000_GCR_TXDSCR_NO_SNOOP)
-/* PHY Control Register */
-#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
-#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
-#define MII_CR_POWER_DOWN 0x0800 /* Power down */
-#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
-#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
-#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
-#define MII_CR_SPEED_1000 0x0040
-#define MII_CR_SPEED_100 0x2000
-#define MII_CR_SPEED_10 0x0000
-
-/* PHY Status Register */
-#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */
-#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */
-
-/* Autoneg Advertisement Register */
-#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */
-#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */
-#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */
-#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */
-#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */
-#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */
-
-/* Link Partner Ability Register (Base Page) */
-#define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP 100TX Full Dplx Capable */
-#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */
-#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */
-
-/* Autoneg Expansion Register */
-#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */
-
-/* 1000BASE-T Control Register */
-#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
-#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
- /* 0=DTE device */
-#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */
- /* 0=Configure PHY as Slave */
-#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */
- /* 0=Automatic Master/Slave config */
-
-/* 1000BASE-T Status Register */
-#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
-#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */
-
-
-/* PHY 1000 MII Register/Bit Definitions */
-/* PHY Registers defined by IEEE */
-#define PHY_CONTROL 0x00 /* Control Register */
-#define PHY_STATUS 0x01 /* Status Register */
-#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
-#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
-#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
-#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */
-#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */
-#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */
-#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
-#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */
-
-#define PHY_CONTROL_LB 0x4000 /* PHY Loopback bit */
-
/* NVM Control */
#define E1000_EECD_SK 0x00000001 /* NVM Clock */
#define E1000_EECD_CS 0x00000002 /* NVM Chip Select */
#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */
#define E1000_EECD_SEC1VAL_VALID_MASK (E1000_EECD_AUTO_RD | E1000_EECD_PRES)
-#define E1000_NVM_RW_REG_DATA 16 /* Offset to data in NVM read/write registers */
-#define E1000_NVM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
-#define E1000_NVM_RW_REG_START 1 /* Start operation */
-#define E1000_NVM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
-#define E1000_NVM_POLL_WRITE 1 /* Flag for polling for write complete */
-#define E1000_NVM_POLL_READ 0 /* Flag for polling for read complete */
-#define E1000_FLASH_UPDATES 2000
+#define E1000_NVM_RW_REG_DATA 16 /* Offset to data in NVM r/w regs */
+#define E1000_NVM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
+#define E1000_NVM_RW_REG_START 1 /* Start operation */
+#define E1000_NVM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
+#define E1000_NVM_POLL_WRITE 1 /* Flag for polling write complete */
+#define E1000_NVM_POLL_READ 0 /* Flag for polling read complete */
+#define E1000_FLASH_UPDATES 2000
/* NVM Word Offsets */
#define NVM_COMPAT 0x0003
#define NVM_ID_LED_SETTINGS 0x0004
+#define NVM_FUTURE_INIT_WORD1 0x0019
+#define NVM_COMPAT_VALID_CSUM 0x0001
+#define NVM_FUTURE_INIT_WORD1_VALID_CSUM 0x0040
+
#define NVM_INIT_CONTROL2_REG 0x000F
#define NVM_INIT_CONTROL3_PORT_B 0x0014
#define NVM_INIT_3GIO_3 0x001A
#define NVM_ALT_MAC_ADDR_PTR 0x0037
#define NVM_CHECKSUM_REG 0x003F
-#define E1000_NVM_INIT_CTRL2_MNGM 0x6000 /* Manageability Operation Mode mask */
-
#define E1000_NVM_CFG_DONE_PORT_0 0x40000 /* MNG config cycle done */
#define E1000_NVM_CFG_DONE_PORT_1 0x80000 /* ...for second port */
#define M88E1000_PSCR_AUTO_X_1000T 0x0040
/* Auto crossover enabled all speeds */
#define M88E1000_PSCR_AUTO_X_MODE 0x0060
-/* 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold)
- * 0=Normal 10BASE-T Rx Threshold
- */
#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
/* M88E1000 PHY Specific Status Register */
/* BME1000 PHY Specific Control Register */
#define BME1000_PSCR_ENABLE_DOWNSHIFT 0x0800 /* 1 = enable downshift */
-
-#define PHY_PAGE_SHIFT 5
-#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
- ((reg) & MAX_PHY_REG_ADDRESS))
-
/* Bits...
* 15-5: page
* 4-0: register offset
GG82563_REG(194, 18) /* Inband Control */
/* MDI Control */
+#define E1000_MDIC_REG_MASK 0x001F0000
#define E1000_MDIC_REG_SHIFT 16
#define E1000_MDIC_PHY_SHIFT 21
#define E1000_MDIC_OP_WRITE 0x04000000
/* SerDes Control */
#define E1000_GEN_POLL_TIMEOUT 640
-/* FW Semaphore */
-#define E1000_FWSM_WLOCK_MAC_MASK 0x0380
-#define E1000_FWSM_WLOCK_MAC_SHIFT 7
-
#endif /* _E1000_DEFINES_H_ */
projects / firefly-linux-kernel-4.4.55.git / blobdiff