* This driver takes one kernel command line parameter, sa1100ir=, with
* the following options:
* max_rate:baudrate - set the maximum baud rate
- * power_leve:level - set the transmitter power level
+ * power_level:level - set the transmitter power level
* tx_lpm:0|1 - set transmit low power mode
*/
#include <linux/module.h>
#include <net/irda/wrapper.h>
#include <net/irda/irda_device.h>
-#include <asm/irq.h>
#include <mach/dma.h>
#include <mach/hardware.h>
#include <asm/mach/irda.h>
static int tx_lpm;
static int max_rate = 4000000;
+struct sa1100_buf {
+ struct sk_buff *skb;
+ struct scatterlist sg;
+ dma_regs_t *regs;
+};
+
struct sa1100_irda {
- unsigned char hscr0;
unsigned char utcr4;
unsigned char power;
unsigned char open;
int speed;
int newspeed;
- struct sk_buff *txskb;
- struct sk_buff *rxskb;
- dma_addr_t txbuf_dma;
- dma_addr_t rxbuf_dma;
- dma_regs_t *txdma;
- dma_regs_t *rxdma;
+ struct sa1100_buf dma_rx;
+ struct sa1100_buf dma_tx;
struct device *dev;
struct irda_platform_data *pdata;
iobuff_t tx_buff;
iobuff_t rx_buff;
+
+ int (*tx_start)(struct sk_buff *, struct net_device *, struct sa1100_irda *);
+ irqreturn_t (*irq)(struct net_device *, struct sa1100_irda *);
};
+static int sa1100_irda_set_speed(struct sa1100_irda *, int);
+
#define IS_FIR(si) ((si)->speed >= 4000000)
#define HPSIR_MAX_RXLEN 2047
*/
static int sa1100_irda_rx_alloc(struct sa1100_irda *si)
{
- if (si->rxskb)
+ if (si->dma_rx.skb)
return 0;
- si->rxskb = alloc_skb(HPSIR_MAX_RXLEN + 1, GFP_ATOMIC);
-
- if (!si->rxskb) {
+ si->dma_rx.skb = alloc_skb(HPSIR_MAX_RXLEN + 1, GFP_ATOMIC);
+ if (!si->dma_rx.skb) {
printk(KERN_ERR "sa1100_ir: out of memory for RX SKB\n");
return -ENOMEM;
}
* Align any IP headers that may be contained
* within the frame.
*/
- skb_reserve(si->rxskb, 1);
+ skb_reserve(si->dma_rx.skb, 1);
+
+ sg_set_buf(&si->dma_rx.sg, si->dma_rx.skb->data, HPSIR_MAX_RXLEN);
+ if (dma_map_sg(si->dev, &si->dma_rx.sg, 1, DMA_FROM_DEVICE) == 0) {
+ dev_kfree_skb_any(si->dma_rx.skb);
+ return -ENOMEM;
+ }
- si->rxbuf_dma = dma_map_single(si->dev, si->rxskb->data,
- HPSIR_MAX_RXLEN,
- DMA_FROM_DEVICE);
return 0;
}
*/
static void sa1100_irda_rx_dma_start(struct sa1100_irda *si)
{
- if (!si->rxskb) {
+ if (!si->dma_rx.skb) {
printk(KERN_ERR "sa1100_ir: rx buffer went missing\n");
return;
}
/*
* First empty receive FIFO
*/
- Ser2HSCR0 = si->hscr0 | HSCR0_HSSP;
+ Ser2HSCR0 = HSCR0_HSSP;
/*
* Enable the DMA, receiver and receive interrupt.
*/
- sa1100_clear_dma(si->rxdma);
- sa1100_start_dma(si->rxdma, si->rxbuf_dma, HPSIR_MAX_RXLEN);
- Ser2HSCR0 = si->hscr0 | HSCR0_HSSP | HSCR0_RXE;
+ sa1100_clear_dma(si->dma_rx.regs);
+ sa1100_start_dma(si->dma_rx.regs, sg_dma_address(&si->dma_rx.sg),
+ sg_dma_len(&si->dma_rx.sg));
+ Ser2HSCR0 = HSCR0_HSSP | HSCR0_RXE;
}
-/*
- * Set the IrDA communications speed.
- */
-static int sa1100_irda_set_speed(struct sa1100_irda *si, int speed)
+static void sa1100_irda_check_speed(struct sa1100_irda *si)
{
- unsigned long flags;
- int brd, ret = -EINVAL;
-
- switch (speed) {
- case 9600: case 19200: case 38400:
- case 57600: case 115200:
- brd = 3686400 / (16 * speed) - 1;
-
- /*
- * Stop the receive DMA.
- */
- if (IS_FIR(si))
- sa1100_stop_dma(si->rxdma);
-
- local_irq_save(flags);
-
- Ser2UTCR3 = 0;
- Ser2HSCR0 = HSCR0_UART;
-
- Ser2UTCR1 = brd >> 8;
- Ser2UTCR2 = brd;
-
- /*
- * Clear status register
- */
- Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID;
- Ser2UTCR3 = UTCR3_RIE | UTCR3_RXE | UTCR3_TXE;
-
- if (si->pdata->set_speed)
- si->pdata->set_speed(si->dev, speed);
-
- si->speed = speed;
-
- local_irq_restore(flags);
- ret = 0;
- break;
-
- case 4000000:
- local_irq_save(flags);
-
- si->hscr0 = 0;
-
- Ser2HSSR0 = 0xff;
- Ser2HSCR0 = si->hscr0 | HSCR0_HSSP;
- Ser2UTCR3 = 0;
-
- si->speed = speed;
-
- if (si->pdata->set_speed)
- si->pdata->set_speed(si->dev, speed);
-
- sa1100_irda_rx_alloc(si);
- sa1100_irda_rx_dma_start(si);
-
- local_irq_restore(flags);
-
- break;
-
- default:
- break;
+ if (si->newspeed) {
+ sa1100_irda_set_speed(si, si->newspeed);
+ si->newspeed = 0;
}
-
- return ret;
}
/*
- * Control the power state of the IrDA transmitter.
- * State:
- * 0 - off
- * 1 - short range, lowest power
- * 2 - medium range, medium power
- * 3 - maximum range, high power
- *
- * Currently, only assabet is known to support this.
+ * HP-SIR format support.
*/
-static int
-__sa1100_irda_set_power(struct sa1100_irda *si, unsigned int state)
-{
- int ret = 0;
- if (si->pdata->set_power)
- ret = si->pdata->set_power(si->dev, state);
- return ret;
-}
-
-static inline int
-sa1100_set_power(struct sa1100_irda *si, unsigned int state)
+static int sa1100_irda_sir_tx_start(struct sk_buff *skb, struct net_device *dev,
+ struct sa1100_irda *si)
{
- int ret;
-
- ret = __sa1100_irda_set_power(si, state);
- if (ret == 0)
- si->power = state;
-
- return ret;
-}
-
-static int sa1100_irda_startup(struct sa1100_irda *si)
-{
- int ret;
+ si->tx_buff.data = si->tx_buff.head;
+ si->tx_buff.len = async_wrap_skb(skb, si->tx_buff.data,
+ si->tx_buff.truesize);
/*
- * Ensure that the ports for this device are setup correctly.
+ * Set the transmit interrupt enable. This will fire off an
+ * interrupt immediately. Note that we disable the receiver
+ * so we won't get spurious characters received.
*/
- if (si->pdata->startup) {
- ret = si->pdata->startup(si->dev);
- if (ret)
- return ret;
- }
-
- /*
- * Configure PPC for IRDA - we want to drive TXD2 low.
- * We also want to drive this pin low during sleep.
- */
- PPSR &= ~PPC_TXD2;
- PSDR &= ~PPC_TXD2;
- PPDR |= PPC_TXD2;
-
- /*
- * Enable HP-SIR modulation, and ensure that the port is disabled.
- */
- Ser2UTCR3 = 0;
- Ser2HSCR0 = HSCR0_UART;
- Ser2UTCR4 = si->utcr4;
- Ser2UTCR0 = UTCR0_8BitData;
- Ser2HSCR2 = HSCR2_TrDataH | HSCR2_RcDataL;
-
- /*
- * Clear status register
- */
- Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID;
-
- ret = sa1100_irda_set_speed(si, si->speed = 9600);
- if (ret) {
- Ser2UTCR3 = 0;
- Ser2HSCR0 = 0;
-
- if (si->pdata->shutdown)
- si->pdata->shutdown(si->dev);
- }
-
- return ret;
-}
-
-static void sa1100_irda_shutdown(struct sa1100_irda *si)
-{
- /*
- * Stop all DMA activity.
- */
- sa1100_stop_dma(si->rxdma);
- sa1100_stop_dma(si->txdma);
-
- /* Disable the port. */
- Ser2UTCR3 = 0;
- Ser2HSCR0 = 0;
-
- if (si->pdata->shutdown)
- si->pdata->shutdown(si->dev);
-}
-
-#ifdef CONFIG_PM
-/*
- * Suspend the IrDA interface.
- */
-static int sa1100_irda_suspend(struct platform_device *pdev, pm_message_t state)
-{
- struct net_device *dev = platform_get_drvdata(pdev);
- struct sa1100_irda *si;
-
- if (!dev)
- return 0;
-
- si = netdev_priv(dev);
- if (si->open) {
- /*
- * Stop the transmit queue
- */
- netif_device_detach(dev);
- disable_irq(dev->irq);
- sa1100_irda_shutdown(si);
- __sa1100_irda_set_power(si, 0);
- }
+ Ser2UTCR3 = UTCR3_TIE | UTCR3_TXE;
- return 0;
-}
+ dev_kfree_skb(skb);
-/*
- * Resume the IrDA interface.
- */
-static int sa1100_irda_resume(struct platform_device *pdev)
-{
- struct net_device *dev = platform_get_drvdata(pdev);
- struct sa1100_irda *si;
-
- if (!dev)
- return 0;
-
- si = netdev_priv(dev);
- if (si->open) {
- /*
- * If we missed a speed change, initialise at the new speed
- * directly. It is debatable whether this is actually
- * required, but in the interests of continuing from where
- * we left off it is desirable. The converse argument is
- * that we should re-negotiate at 9600 baud again.
- */
- if (si->newspeed) {
- si->speed = si->newspeed;
- si->newspeed = 0;
- }
-
- sa1100_irda_startup(si);
- __sa1100_irda_set_power(si, si->power);
- enable_irq(dev->irq);
-
- /*
- * This automatically wakes up the queue
- */
- netif_device_attach(dev);
- }
-
- return 0;
+ return NETDEV_TX_OK;
}
-#else
-#define sa1100_irda_suspend NULL
-#define sa1100_irda_resume NULL
-#endif
-/*
- * HP-SIR format interrupt service routines.
- */
-static void sa1100_irda_hpsir_irq(struct net_device *dev)
+static irqreturn_t sa1100_irda_sir_irq(struct net_device *dev, struct sa1100_irda *si)
{
- struct sa1100_irda *si = netdev_priv(dev);
int status;
status = Ser2UTSR0;
Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID;
Ser2UTCR3 = UTCR3_RIE | UTCR3_RXE | UTCR3_TXE;
- if (si->newspeed) {
- sa1100_irda_set_speed(si, si->newspeed);
- si->newspeed = 0;
- }
+ sa1100_irda_check_speed(si);
/* I'm hungry! */
netif_wake_queue(dev);
}
}
+
+ return IRQ_HANDLED;
+}
+
+/*
+ * FIR format support.
+ */
+static void sa1100_irda_firtxdma_irq(void *id)
+{
+ struct net_device *dev = id;
+ struct sa1100_irda *si = netdev_priv(dev);
+ struct sk_buff *skb;
+
+ /*
+ * Wait for the transmission to complete. Unfortunately,
+ * the hardware doesn't give us an interrupt to indicate
+ * "end of frame".
+ */
+ do
+ rmb();
+ while (!(Ser2HSSR0 & HSSR0_TUR) || Ser2HSSR1 & HSSR1_TBY);
+
+ /*
+ * Clear the transmit underrun bit.
+ */
+ Ser2HSSR0 = HSSR0_TUR;
+
+ /*
+ * Do we need to change speed? Note that we're lazy
+ * here - we don't free the old dma_rx.skb. We don't need
+ * to allocate a buffer either.
+ */
+ sa1100_irda_check_speed(si);
+
+ /*
+ * Start reception. This disables the transmitter for
+ * us. This will be using the existing RX buffer.
+ */
+ sa1100_irda_rx_dma_start(si);
+
+ /* Account and free the packet. */
+ skb = si->dma_tx.skb;
+ if (skb) {
+ dma_unmap_sg(si->dev, &si->dma_tx.sg, 1,
+ DMA_TO_DEVICE);
+ dev->stats.tx_packets ++;
+ dev->stats.tx_bytes += skb->len;
+ dev_kfree_skb_irq(skb);
+ si->dma_tx.skb = NULL;
+ }
+
+ /*
+ * Make sure that the TX queue is available for sending
+ * (for retries). TX has priority over RX at all times.
+ */
+ netif_wake_queue(dev);
+}
+
+static int sa1100_irda_fir_tx_start(struct sk_buff *skb, struct net_device *dev,
+ struct sa1100_irda *si)
+{
+ int mtt = irda_get_mtt(skb);
+
+ si->dma_tx.skb = skb;
+ sg_set_buf(&si->dma_tx.sg, skb->data, skb->len);
+ if (dma_map_sg(si->dev, &si->dma_tx.sg, 1, DMA_TO_DEVICE) == 0) {
+ si->dma_tx.skb = NULL;
+ netif_wake_queue(dev);
+ dev->stats.tx_dropped++;
+ dev_kfree_skb(skb);
+ return NETDEV_TX_OK;
+ }
+
+ sa1100_start_dma(si->dma_tx.regs, sg_dma_address(&si->dma_tx.sg),
+ sg_dma_len(&si->dma_tx.sg));
+
+ /*
+ * If we have a mean turn-around time, impose the specified
+ * specified delay. We could shorten this by timing from
+ * the point we received the packet.
+ */
+ if (mtt)
+ udelay(mtt);
+
+ Ser2HSCR0 = HSCR0_HSSP | HSCR0_TXE;
+
+ return NETDEV_TX_OK;
}
static void sa1100_irda_fir_error(struct sa1100_irda *si, struct net_device *dev)
{
- struct sk_buff *skb = si->rxskb;
+ struct sk_buff *skb = si->dma_rx.skb;
dma_addr_t dma_addr;
unsigned int len, stat, data;
/*
* Get the current data position.
*/
- dma_addr = sa1100_get_dma_pos(si->rxdma);
- len = dma_addr - si->rxbuf_dma;
+ dma_addr = sa1100_get_dma_pos(si->dma_rx.regs);
+ len = dma_addr - sg_dma_address(&si->dma_rx.sg);
if (len > HPSIR_MAX_RXLEN)
len = HPSIR_MAX_RXLEN;
- dma_unmap_single(si->dev, si->rxbuf_dma, len, DMA_FROM_DEVICE);
+ dma_unmap_sg(si->dev, &si->dma_rx.sg, 1, DMA_FROM_DEVICE);
do {
/*
} while (Ser2HSSR0 & HSSR0_EIF);
if (stat & HSSR1_EOF) {
- si->rxskb = NULL;
+ si->dma_rx.skb = NULL;
skb_put(skb, len);
skb->dev = dev;
netif_rx(skb);
} else {
/*
- * Remap the buffer.
+ * Remap the buffer - it was previously mapped, and we
+ * hope that this succeeds.
*/
- si->rxbuf_dma = dma_map_single(si->dev, si->rxskb->data,
- HPSIR_MAX_RXLEN,
- DMA_FROM_DEVICE);
+ dma_map_sg(si->dev, &si->dma_rx.sg, 1, DMA_FROM_DEVICE);
}
}
/*
- * FIR format interrupt service routine. We only have to
- * handle RX events; transmit events go via the TX DMA handler.
- *
- * No matter what, we disable RX, process, and the restart RX.
+ * We only have to handle RX events here; transmit events go via the TX
+ * DMA handler. We disable RX, process, and the restart RX.
*/
-static void sa1100_irda_fir_irq(struct net_device *dev)
+static irqreturn_t sa1100_irda_fir_irq(struct net_device *dev, struct sa1100_irda *si)
{
- struct sa1100_irda *si = netdev_priv(dev);
-
/*
* Stop RX DMA
*/
- sa1100_stop_dma(si->rxdma);
+ sa1100_stop_dma(si->dma_rx.regs);
/*
* Framing error - we throw away the packet completely.
/*
* Clear out the DMA...
*/
- Ser2HSCR0 = si->hscr0 | HSCR0_HSSP;
+ Ser2HSCR0 = HSCR0_HSSP;
/*
* Clear selected status bits now, so we
* No matter what happens, we must restart reception.
*/
sa1100_irda_rx_dma_start(si);
+
+ return IRQ_HANDLED;
}
-static irqreturn_t sa1100_irda_irq(int irq, void *dev_id)
+/*
+ * Set the IrDA communications speed.
+ */
+static int sa1100_irda_set_speed(struct sa1100_irda *si, int speed)
{
- struct net_device *dev = dev_id;
- if (IS_FIR(((struct sa1100_irda *)netdev_priv(dev))))
- sa1100_irda_fir_irq(dev);
- else
- sa1100_irda_hpsir_irq(dev);
- return IRQ_HANDLED;
+ unsigned long flags;
+ int brd, ret = -EINVAL;
+
+ switch (speed) {
+ case 9600: case 19200: case 38400:
+ case 57600: case 115200:
+ brd = 3686400 / (16 * speed) - 1;
+
+ /*
+ * Stop the receive DMA.
+ */
+ if (IS_FIR(si))
+ sa1100_stop_dma(si->dma_rx.regs);
+
+ local_irq_save(flags);
+
+ Ser2UTCR3 = 0;
+ Ser2HSCR0 = HSCR0_UART;
+
+ Ser2UTCR1 = brd >> 8;
+ Ser2UTCR2 = brd;
+
+ /*
+ * Clear status register
+ */
+ Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID;
+ Ser2UTCR3 = UTCR3_RIE | UTCR3_RXE | UTCR3_TXE;
+
+ if (si->pdata->set_speed)
+ si->pdata->set_speed(si->dev, speed);
+
+ si->speed = speed;
+ si->tx_start = sa1100_irda_sir_tx_start;
+ si->irq = sa1100_irda_sir_irq;
+
+ local_irq_restore(flags);
+ ret = 0;
+ break;
+
+ case 4000000:
+ local_irq_save(flags);
+
+ Ser2HSSR0 = 0xff;
+ Ser2HSCR0 = HSCR0_HSSP;
+ Ser2UTCR3 = 0;
+
+ si->speed = speed;
+ si->tx_start = sa1100_irda_fir_tx_start;
+ si->irq = sa1100_irda_fir_irq;
+
+ if (si->pdata->set_speed)
+ si->pdata->set_speed(si->dev, speed);
+
+ sa1100_irda_rx_alloc(si);
+ sa1100_irda_rx_dma_start(si);
+
+ local_irq_restore(flags);
+
+ break;
+
+ default:
+ break;
+ }
+
+ return ret;
}
/*
- * TX DMA completion handler.
+ * Control the power state of the IrDA transmitter.
+ * State:
+ * 0 - off
+ * 1 - short range, lowest power
+ * 2 - medium range, medium power
+ * 3 - maximum range, high power
+ *
+ * Currently, only assabet is known to support this.
*/
-static void sa1100_irda_txdma_irq(void *id)
+static int
+__sa1100_irda_set_power(struct sa1100_irda *si, unsigned int state)
{
- struct net_device *dev = id;
- struct sa1100_irda *si = netdev_priv(dev);
- struct sk_buff *skb = si->txskb;
-
- si->txskb = NULL;
-
- /*
- * Wait for the transmission to complete. Unfortunately,
- * the hardware doesn't give us an interrupt to indicate
- * "end of frame".
- */
- do
- rmb();
- while (!(Ser2HSSR0 & HSSR0_TUR) || Ser2HSSR1 & HSSR1_TBY);
+ int ret = 0;
+ if (si->pdata->set_power)
+ ret = si->pdata->set_power(si->dev, state);
+ return ret;
+}
- /*
- * Clear the transmit underrun bit.
- */
- Ser2HSSR0 = HSSR0_TUR;
+static inline int
+sa1100_set_power(struct sa1100_irda *si, unsigned int state)
+{
+ int ret;
- /*
- * Do we need to change speed? Note that we're lazy
- * here - we don't free the old rxskb. We don't need
- * to allocate a buffer either.
- */
- if (si->newspeed) {
- sa1100_irda_set_speed(si, si->newspeed);
- si->newspeed = 0;
- }
+ ret = __sa1100_irda_set_power(si, state);
+ if (ret == 0)
+ si->power = state;
- /*
- * Start reception. This disables the transmitter for
- * us. This will be using the existing RX buffer.
- */
- sa1100_irda_rx_dma_start(si);
+ return ret;
+}
- /*
- * Account and free the packet.
- */
- if (skb) {
- dma_unmap_single(si->dev, si->txbuf_dma, skb->len, DMA_TO_DEVICE);
- dev->stats.tx_packets ++;
- dev->stats.tx_bytes += skb->len;
- dev_kfree_skb_irq(skb);
- }
+static irqreturn_t sa1100_irda_irq(int irq, void *dev_id)
+{
+ struct net_device *dev = dev_id;
+ struct sa1100_irda *si = netdev_priv(dev);
- /*
- * Make sure that the TX queue is available for sending
- * (for retries). TX has priority over RX at all times.
- */
- netif_wake_queue(dev);
+ return si->irq(dev, si);
}
static int sa1100_irda_hard_xmit(struct sk_buff *skb, struct net_device *dev)
if (speed != si->speed && speed != -1)
si->newspeed = speed;
- /*
- * If this is an empty frame, we can bypass a lot.
- */
+ /* If this is an empty frame, we can bypass a lot. */
if (skb->len == 0) {
- if (si->newspeed) {
- si->newspeed = 0;
- sa1100_irda_set_speed(si, speed);
- }
+ sa1100_irda_check_speed(si);
dev_kfree_skb(skb);
return NETDEV_TX_OK;
}
- if (!IS_FIR(si)) {
- netif_stop_queue(dev);
-
- si->tx_buff.data = si->tx_buff.head;
- si->tx_buff.len = async_wrap_skb(skb, si->tx_buff.data,
- si->tx_buff.truesize);
-
- /*
- * Set the transmit interrupt enable. This will fire
- * off an interrupt immediately. Note that we disable
- * the receiver so we won't get spurious characteres
- * received.
- */
- Ser2UTCR3 = UTCR3_TIE | UTCR3_TXE;
-
- dev_kfree_skb(skb);
- } else {
- int mtt = irda_get_mtt(skb);
-
- /*
- * We must not be transmitting...
- */
- BUG_ON(si->txskb);
-
- netif_stop_queue(dev);
-
- si->txskb = skb;
- si->txbuf_dma = dma_map_single(si->dev, skb->data,
- skb->len, DMA_TO_DEVICE);
-
- sa1100_start_dma(si->txdma, si->txbuf_dma, skb->len);
-
- /*
- * If we have a mean turn-around time, impose the specified
- * specified delay. We could shorten this by timing from
- * the point we received the packet.
- */
- if (mtt)
- udelay(mtt);
+ netif_stop_queue(dev);
- Ser2HSCR0 = si->hscr0 | HSCR0_HSSP | HSCR0_TXE;
- }
+ /* We must not already have a skb to transmit... */
+ BUG_ON(si->dma_tx.skb);
- return NETDEV_TX_OK;
+ return si->tx_start(skb, dev, si);
}
static int
return ret;
}
+static int sa1100_irda_startup(struct sa1100_irda *si)
+{
+ int ret;
+
+ /*
+ * Ensure that the ports for this device are setup correctly.
+ */
+ if (si->pdata->startup) {
+ ret = si->pdata->startup(si->dev);
+ if (ret)
+ return ret;
+ }
+
+ /*
+ * Configure PPC for IRDA - we want to drive TXD2 low.
+ * We also want to drive this pin low during sleep.
+ */
+ PPSR &= ~PPC_TXD2;
+ PSDR &= ~PPC_TXD2;
+ PPDR |= PPC_TXD2;
+
+ /*
+ * Enable HP-SIR modulation, and ensure that the port is disabled.
+ */
+ Ser2UTCR3 = 0;
+ Ser2HSCR0 = HSCR0_UART;
+ Ser2UTCR4 = si->utcr4;
+ Ser2UTCR0 = UTCR0_8BitData;
+ Ser2HSCR2 = HSCR2_TrDataH | HSCR2_RcDataL;
+
+ /*
+ * Clear status register
+ */
+ Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID;
+
+ ret = sa1100_irda_set_speed(si, si->speed = 9600);
+ if (ret) {
+ Ser2UTCR3 = 0;
+ Ser2HSCR0 = 0;
+
+ if (si->pdata->shutdown)
+ si->pdata->shutdown(si->dev);
+ }
+
+ return ret;
+}
+
+static void sa1100_irda_shutdown(struct sa1100_irda *si)
+{
+ /*
+ * Stop all DMA activity.
+ */
+ sa1100_stop_dma(si->dma_rx.regs);
+ sa1100_stop_dma(si->dma_tx.regs);
+
+ /* Disable the port. */
+ Ser2UTCR3 = 0;
+ Ser2HSCR0 = 0;
+
+ if (si->pdata->shutdown)
+ si->pdata->shutdown(si->dev);
+}
+
static int sa1100_irda_start(struct net_device *dev)
{
struct sa1100_irda *si = netdev_priv(dev);
si->speed = 9600;
- err = request_irq(dev->irq, sa1100_irda_irq, 0, dev->name, dev);
- if (err)
- goto err_irq;
-
err = sa1100_request_dma(DMA_Ser2HSSPRd, "IrDA receive",
- NULL, NULL, &si->rxdma);
+ NULL, NULL, &si->dma_rx.regs);
if (err)
goto err_rx_dma;
err = sa1100_request_dma(DMA_Ser2HSSPWr, "IrDA transmit",
- sa1100_irda_txdma_irq, dev, &si->txdma);
+ sa1100_irda_firtxdma_irq, dev,
+ &si->dma_tx.regs);
if (err)
goto err_tx_dma;
- /*
- * The interrupt must remain disabled for now.
- */
- disable_irq(dev->irq);
-
/*
* Setup the serial port for the specified speed.
*/
if (!si->irlap)
goto err_irlap;
+ err = request_irq(dev->irq, sa1100_irda_irq, 0, dev->name, dev);
+ if (err)
+ goto err_irq;
+
/*
* Now enable the interrupt and start the queue
*/
si->open = 1;
sa1100_set_power(si, power_level); /* low power mode */
- enable_irq(dev->irq);
+
netif_start_queue(dev);
return 0;
+err_irq:
+ irlap_close(si->irlap);
err_irlap:
si->open = 0;
sa1100_irda_shutdown(si);
err_startup:
- sa1100_free_dma(si->txdma);
+ sa1100_free_dma(si->dma_tx.regs);
err_tx_dma:
- sa1100_free_dma(si->rxdma);
+ sa1100_free_dma(si->dma_rx.regs);
err_rx_dma:
- free_irq(dev->irq, dev);
-err_irq:
return err;
}
static int sa1100_irda_stop(struct net_device *dev)
{
struct sa1100_irda *si = netdev_priv(dev);
+ struct sk_buff *skb;
- disable_irq(dev->irq);
+ netif_stop_queue(dev);
+
+ si->open = 0;
sa1100_irda_shutdown(si);
/*
- * If we have been doing DMA receive, make sure we
+ * If we have been doing any DMA activity, make sure we
* tidy that up cleanly.
*/
- if (si->rxskb) {
- dma_unmap_single(si->dev, si->rxbuf_dma, HPSIR_MAX_RXLEN,
- DMA_FROM_DEVICE);
- dev_kfree_skb(si->rxskb);
- si->rxskb = NULL;
+ skb = si->dma_rx.skb;
+ if (skb) {
+ dma_unmap_sg(si->dev, &si->dma_rx.sg, 1,
+ DMA_FROM_DEVICE);
+ dev_kfree_skb(skb);
+ si->dma_rx.skb = NULL;
+ }
+
+ skb = si->dma_tx.skb;
+ if (skb) {
+ dma_unmap_sg(si->dev, &si->dma_tx.sg, 1,
+ DMA_TO_DEVICE);
+ dev_kfree_skb(skb);
+ si->dma_tx.skb = NULL;
}
/* Stop IrLAP */
si->irlap = NULL;
}
- netif_stop_queue(dev);
- si->open = 0;
-
/*
* Free resources
*/
- sa1100_free_dma(si->txdma);
- sa1100_free_dma(si->rxdma);
+ sa1100_free_dma(si->dma_tx.regs);
+ sa1100_free_dma(si->dma_rx.regs);
free_irq(dev->irq, dev);
sa1100_set_power(si, 0);
struct net_device *dev;
struct sa1100_irda *si;
unsigned int baudrate_mask;
- int err;
+ int err, irq;
if (!pdev->dev.platform_data)
return -EINVAL;
+ irq = platform_get_irq(pdev, 0);
+ if (irq <= 0)
+ return irq < 0 ? irq : -ENXIO;
+
err = request_mem_region(__PREG(Ser2UTCR0), 0x24, "IrDA") ? 0 : -EBUSY;
if (err)
goto err_mem_1;
if (!dev)
goto err_mem_4;
+ SET_NETDEV_DEV(dev, &pdev->dev);
+
si = netdev_priv(dev);
si->dev = &pdev->dev;
si->pdata = pdev->dev.platform_data;
+ sg_init_table(&si->dma_rx.sg, 1);
+ sg_init_table(&si->dma_tx.sg, 1);
+
/*
* Initialise the HP-SIR buffers
*/
goto err_mem_5;
dev->netdev_ops = &sa1100_irda_netdev_ops;
- dev->irq = IRQ_Ser2ICP;
+ dev->irq = irq;
irda_init_max_qos_capabilies(&si->qos);
return 0;
}
+#ifdef CONFIG_PM
+/*
+ * Suspend the IrDA interface.
+ */
+static int sa1100_irda_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ struct net_device *dev = platform_get_drvdata(pdev);
+ struct sa1100_irda *si;
+
+ if (!dev)
+ return 0;
+
+ si = netdev_priv(dev);
+ if (si->open) {
+ /*
+ * Stop the transmit queue
+ */
+ netif_device_detach(dev);
+ disable_irq(dev->irq);
+ sa1100_irda_shutdown(si);
+ __sa1100_irda_set_power(si, 0);
+ }
+
+ return 0;
+}
+
+/*
+ * Resume the IrDA interface.
+ */
+static int sa1100_irda_resume(struct platform_device *pdev)
+{
+ struct net_device *dev = platform_get_drvdata(pdev);
+ struct sa1100_irda *si;
+
+ if (!dev)
+ return 0;
+
+ si = netdev_priv(dev);
+ if (si->open) {
+ /*
+ * If we missed a speed change, initialise at the new speed
+ * directly. It is debatable whether this is actually
+ * required, but in the interests of continuing from where
+ * we left off it is desirable. The converse argument is
+ * that we should re-negotiate at 9600 baud again.
+ */
+ if (si->newspeed) {
+ si->speed = si->newspeed;
+ si->newspeed = 0;
+ }
+
+ sa1100_irda_startup(si);
+ __sa1100_irda_set_power(si, si->power);
+ enable_irq(dev->irq);
+
+ /*
+ * This automatically wakes up the queue
+ */
+ netif_device_attach(dev);
+ }
+
+ return 0;
+}
+#else
+#define sa1100_irda_suspend NULL
+#define sa1100_irda_resume NULL
+#endif
+
static struct platform_driver sa1100ir_driver = {
.probe = sa1100_irda_probe,
.remove = sa1100_irda_remove,