REPLY_TX_POWER_DBM_CMD = 0x98,
MEASURE_ABORT_NOTIFICATION = 0x99, /* not used */
- /* Bluetooth device coexistance config command */
+ /* Bluetooth device coexistence config command */
REPLY_BT_CONFIG = 0x9b,
/* Statistics */
u8 cmd; /* Command ID: REPLY_RXON, etc. */
u8 flags; /* 0:5 reserved, 6 abort, 7 internal */
/*
- * The driver sets up the sequence number to values of its chosing.
+ * The driver sets up the sequence number to values of its choosing.
* uCode does not use this value, but passes it back to the driver
* when sending the response to each driver-originated command, so
* the driver can match the response to the command. Since the values
} __attribute__ ((packed));
/**
- * Commad REPLY_TX_POWER_DBM_CMD = 0x98
+ * Command REPLY_TX_POWER_DBM_CMD = 0x98
* struct iwl5000_tx_power_dbm_cmd
*/
#define IWL50_TX_POWER_AUTO 0x7f
* calculating txpower settings:
*
* 1) Power supply voltage indication. The voltage sensor outputs higher
- * values for lower voltage, and vice versa.
+ * values for lower voltage, and vice verse.
*
* 2) Temperature measurement parameters, for each of two channel widths
* (20 MHz and 40 MHz) supported by the radios. Temperature sensing
u8 ofdm_ht_dual_stream_basic_rates;
} __attribute__ ((packed));
-/* 5000 HW just extend this cmmand */
+/* 5000 HW just extend this command */
struct iwl_rxon_cmd {
u8 node_addr[6];
__le16 reserved1;
#define IWL50_OFDM_RSSI_C_BIT_POS 0
struct iwl5000_non_cfg_phy {
- __le32 non_cfg_phy[IWL50_RX_RES_PHY_CNT]; /* upto 8 phy entries */
+ __le32 non_cfg_phy[IWL50_RX_RES_PHY_CNT]; /* up to 8 phy entries */
} __attribute__ ((packed));
/* REPLY_TX Tx flags field */
-/* 1: Use RTS/CTS protocol or CTS-to-self if spec alows it
+/* 1: Use RTS/CTS protocol or CTS-to-self if spec allows it
* before this frame. if CTS-to-self required check
* RXON_FLG_SELF_CTS_EN status. */
#define TX_CMD_FLG_RTS_CTS_MSK __constant_cpu_to_le32(1 << 0)
/*
* definitions for initial rate index field
- * bits [3:0] inital rate index
+ * bits [3:0] initial rate index
* bits [6:4] rate table color, used for the initial rate
* bit-7 invalid rate indication
* i.e. rate was not chosen from rate table
* match the modulation characteristics of the history set.
*
* When using block-ack (aggregation), all frames are transmitted at the same
- * rate, since there is no per-attempt acknowledgement from the destination
+ * rate, since there is no per-attempt acknowledgment from the destination
* station. The Tx response struct iwl_tx_resp indicates the Tx rate in
* rate_n_flags field. After receiving a block-ack, the driver can update
* history for the entire block all at once.
*
* 3945 and 4965 support hardware handshake with Bluetooth device on
* same platform. Bluetooth device alerts wireless device when it will Tx;
- * wireless device can delay or kill its own Tx to accomodate.
+ * wireless device can delay or kill its own Tx to accommodate.
*/
struct iwl4965_bt_cmd {
u8 flags;
* '11' Illegal set
*
* NOTE: if sleep_interval[SLEEP_INTRVL_TABLE_SIZE-1] > DTIM period then
- * ucode assume sleep over DTIM is allowed and we don't need to wakeup
+ * ucode assume sleep over DTIM is allowed and we don't need to wake up
* for every DTIM.
*/
#define IWL_POWER_VEC_SIZE 5
/* COEX flag masks */
-/* Staion table is valid */
+/* Station table is valid */
#define COEX_FLAGS_STA_TABLE_VALID_MSK (0x1)
-/* UnMask wakeup src at unassociated sleep */
+/* UnMask wake up src at unassociated sleep */
#define COEX_FLAGS_UNASSOC_WA_UNMASK_MSK (0x4)
-/* UnMask wakeup src at associated sleep */
+/* UnMask wake up src at associated sleep */
#define COEX_FLAGS_ASSOC_WA_UNMASK_MSK (0x8)
/* Enable CoEx feature. */
#define COEX_FLAGS_COEX_ENABLE_MSK (0x80)