* since the self-test for chip takes a while
*/
#define POR_RETRY_COUNT 5
-/*
- * legacy rfkill support where-in 3 rfkill
- * devices are created for the 3 gpios
- * that ST has requested
- */
-/* chip version storage
+/**
+ * struct chip_version - save the chip version
*/
struct chip_version {
unsigned short full;
unsigned short maj_ver;
};
-/*
- * header file for ST provided by KIM
+/**
+ * struct kim_data_s - the KIM internal data, embedded as the
+ * platform's drv data. One for each ST device in the system.
+ * @uim_pid: KIM needs to communicate with UIM to request to install
+ * the ldisc by opening UART when protocol drivers register.
+ * @kim_pdev: the platform device added in one of the board-XX.c file
+ * in arch/XX/ directory, 1 for each ST device.
+ * @kim_rcvd: completion handler to notify when data was received,
+ * mainly used during fw download, which involves multiple send/wait
+ * for each of the HCI-VS commands.
+ * @ldisc_installed: completion handler to notify that the UIM accepted
+ * the request to install ldisc, notify from tty_open which suggests
+ * the ldisc was properly installed.
+ * @resp_buffer: data buffer for the .bts fw file name.
+ * @fw_entry: firmware class struct to request/release the fw.
+ * @gpios: the list of core/chip enable gpios for BT, FM and GPS cores.
+ * @rx_state: the rx state for kim's receive func during fw download.
+ * @rx_count: the rx count for the kim's receive func during fw download.
+ * @rx_skb: all of fw data might not come at once, and hence data storage for
+ * whole of the fw response, only HCI_EVENTs and hence diff from ST's
+ * response.
+ * @rfkill: rfkill data for each of the cores to be registered with rfkill.
+ * @rf_protos: proto types of the data registered with rfkill sub-system.
+ * @core_data: ST core's data, which mainly is the tty's disc_data
+ * @version: chip version available via a sysfs entry.
+ *
*/
struct kim_data_s {
long uim_pid;
struct platform_device *kim_pdev;
struct completion kim_rcvd, ldisc_installed;
- /* MAX len of the .bts firmware script name */
char resp_buffer[30];
const struct firmware *fw_entry;
long gpios[ST_MAX];
-/* used by kim_int_recv to validate fw response */
unsigned long rx_state;
unsigned long rx_count;
struct sk_buff *rx_skb;
struct chip_version version;
};
+/**
+ * functions called when 1 of the protocol drivers gets
+ * registered, these need to communicate with UIM to request
+ * ldisc installed, read chip_version, download relevant fw
+ */
long st_kim_start(void *);
long st_kim_stop(void *);
-/*
- * called from st_tty_receive to authenticate fw_download
- */
-void st_kim_recv(void *, const unsigned char *, long count);
+void st_kim_recv(void *, const unsigned char *, long count);
void st_kim_chip_toggle(enum proto_type, enum kim_gpio_state);
-
void st_kim_complete(void *);
-
-/* function called from ST KIM to ST Core, to
- * list out the protocols registered
- */
void kim_st_list_protocols(struct st_data_s *, char *);
/*
#define ACTION_RUN_SCRIPT 5
#define ACTION_REMARKS 6
-/*
- * * BRF Firmware header
- * */
+/**
+ * struct bts_header - the fw file is NOT binary which can
+ * be sent onto TTY as is. The .bts is more a script
+ * file which has different types of actions.
+ * Each such action needs to be parsed by the KIM and
+ * relevant procedure to be called.
+ */
struct bts_header {
uint32_t magic;
uint32_t version;
uint8_t actions[0];
} __attribute__ ((packed));
-/*
- * * BRF Actions structure
- * */
+/**
+ * struct bts_action - Each .bts action has its own type of
+ * data.
+ */
struct bts_action {
uint16_t type;
uint16_t size;
uint32_t flow_control;
} __attribute__ ((packed));
-/* for identifying the change speed HCI VS
- * command
+/**
+ * struct hci_command - the HCI-VS for intrepreting
+ * the change baud rate of host-side UART, which
+ * needs to be ignored, since UIM would do that
+ * when it receives request from KIM for ldisc installation.
*/
struct hci_command {
uint8_t prefix;