/*
- * Xilinx calls it "PLB TFT LCD Controller" though it can also be used for
+ * Xilinx calls it "TFT LCD Controller" though it can also be used for
* the VGA port on the Xilinx ML40x board. This is a hardware display
* controller for a 640x480 resolution TFT or VGA screen.
*
* don't start thinking about scrolling). The second allows the LCD to
* be turned on or off as well as rotated 180 degrees.
*
- * In case of direct PLB access the second control register will be at
+ * In case of direct BUS access the second control register will be at
* an offset of 4 as compared to the DCR access where the offset is 1
* i.e. REG_CTRL. So this is taken care in the function
- * xilinx_fb_out_be32 where it left shifts the offset 2 times in case of
- * direct PLB access.
+ * xilinx_fb_out32 where it left shifts the offset 2 times in case of
+ * direct BUS access.
*/
#define NUM_REGS 2
#define REG_FB_ADDR 0
};
-#define PLB_ACCESS_FLAG 0x1 /* 1 = PLB, 0 = DCR */
+#define BUS_ACCESS_FLAG 0x1 /* 1 = BUS, 0 = DCR */
struct xilinxfb_drvdata {
container_of(_info, struct xilinxfb_drvdata, info)
/*
- * The XPS TFT Controller can be accessed through PLB or DCR interface.
+ * The XPS TFT Controller can be accessed through BUS or DCR interface.
* To perform the read/write on the registers we need to check on
* which bus its connected and call the appropriate write API.
*/
-static void xilinx_fb_out_be32(struct xilinxfb_drvdata *drvdata, u32 offset,
+static void xilinx_fb_out32(struct xilinxfb_drvdata *drvdata, u32 offset,
u32 val)
{
- if (drvdata->flags & PLB_ACCESS_FLAG)
+ if (drvdata->flags & BUS_ACCESS_FLAG)
out_be32(drvdata->regs + (offset << 2), val);
#ifdef CONFIG_PPC_DCR
else
switch (blank_mode) {
case FB_BLANK_UNBLANK:
/* turn on panel */
- xilinx_fb_out_be32(drvdata, REG_CTRL, drvdata->reg_ctrl_default);
+ xilinx_fb_out32(drvdata, REG_CTRL, drvdata->reg_ctrl_default);
break;
case FB_BLANK_NORMAL:
case FB_BLANK_HSYNC_SUSPEND:
case FB_BLANK_POWERDOWN:
/* turn off panel */
- xilinx_fb_out_be32(drvdata, REG_CTRL, 0);
+ xilinx_fb_out32(drvdata, REG_CTRL, 0);
default:
break;
* Bus independent setup/teardown
*/
-static int xilinxfb_assign(struct device *dev,
+static int xilinxfb_assign(struct platform_device *pdev,
struct xilinxfb_drvdata *drvdata,
- unsigned long physaddr,
struct xilinxfb_platform_data *pdata)
{
int rc;
+ struct device *dev = &pdev->dev;
int fbsize = pdata->xvirt * pdata->yvirt * BYTES_PER_PIXEL;
- if (drvdata->flags & PLB_ACCESS_FLAG) {
- /*
- * Map the control registers in if the controller
- * is on direct PLB interface.
- */
- if (!request_mem_region(physaddr, 8, DRIVER_NAME)) {
- dev_err(dev, "Couldn't lock memory region at 0x%08lX\n",
- physaddr);
- rc = -ENODEV;
- goto err_region;
- }
+ if (drvdata->flags & BUS_ACCESS_FLAG) {
+ struct resource *res;
- drvdata->regs_phys = physaddr;
- drvdata->regs = ioremap(physaddr, 8);
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ drvdata->regs_phys = res->start;
+ drvdata->regs = devm_request_and_ioremap(&pdev->dev, res);
if (!drvdata->regs) {
- dev_err(dev, "Couldn't lock memory region at 0x%08lX\n",
- physaddr);
- rc = -ENODEV;
- goto err_map;
+ rc = -EADDRNOTAVAIL;
+ goto err_region;
}
}
if (!drvdata->fb_virt) {
dev_err(dev, "Could not allocate frame buffer memory\n");
rc = -ENOMEM;
- if (drvdata->flags & PLB_ACCESS_FLAG)
+ if (drvdata->flags & BUS_ACCESS_FLAG)
goto err_fbmem;
else
goto err_region;
memset_io((void __iomem *)drvdata->fb_virt, 0, fbsize);
/* Tell the hardware where the frame buffer is */
- xilinx_fb_out_be32(drvdata, REG_FB_ADDR, drvdata->fb_phys);
+ xilinx_fb_out32(drvdata, REG_FB_ADDR, drvdata->fb_phys);
/* Turn on the display */
drvdata->reg_ctrl_default = REG_CTRL_ENABLE;
if (pdata->rotate_screen)
drvdata->reg_ctrl_default |= REG_CTRL_ROTATE;
- xilinx_fb_out_be32(drvdata, REG_CTRL,
+ xilinx_fb_out32(drvdata, REG_CTRL,
drvdata->reg_ctrl_default);
/* Fill struct fb_info */
goto err_regfb;
}
- if (drvdata->flags & PLB_ACCESS_FLAG) {
+ if (drvdata->flags & BUS_ACCESS_FLAG) {
/* Put a banner in the log (for DEBUG) */
- dev_dbg(dev, "regs: phys=%lx, virt=%p\n", physaddr,
+ dev_dbg(dev, "regs: phys=%x, virt=%p\n", drvdata->regs_phys,
drvdata->regs);
}
/* Put a banner in the log (for DEBUG) */
iounmap(drvdata->fb_virt);
/* Turn off the display */
- xilinx_fb_out_be32(drvdata, REG_CTRL, 0);
+ xilinx_fb_out32(drvdata, REG_CTRL, 0);
err_fbmem:
- if (drvdata->flags & PLB_ACCESS_FLAG)
- iounmap(drvdata->regs);
-
-err_map:
- if (drvdata->flags & PLB_ACCESS_FLAG)
- release_mem_region(physaddr, 8);
+ if (drvdata->flags & BUS_ACCESS_FLAG)
+ devm_iounmap(dev, drvdata->regs);
err_region:
kfree(drvdata);
iounmap(drvdata->fb_virt);
/* Turn off the display */
- xilinx_fb_out_be32(drvdata, REG_CTRL, 0);
+ xilinx_fb_out32(drvdata, REG_CTRL, 0);
/* Release the resources, as allocated based on interface */
- if (drvdata->flags & PLB_ACCESS_FLAG) {
- iounmap(drvdata->regs);
- release_mem_region(drvdata->regs_phys, 8);
- }
+ if (drvdata->flags & BUS_ACCESS_FLAG)
+ devm_iounmap(dev, drvdata->regs);
#ifdef CONFIG_PPC_DCR
else
dcr_unmap(drvdata->dcr_host, drvdata->dcr_len);
static int xilinxfb_of_probe(struct platform_device *op)
{
const u32 *prop;
- u32 *p;
- u32 tft_access;
+ u32 tft_access = 0;
struct xilinxfb_platform_data pdata;
- struct resource res;
- int size, rc;
+ int size;
struct xilinxfb_drvdata *drvdata;
/* Copy with the default pdata (not a ptr reference!) */
}
/*
- * To check whether the core is connected directly to DCR or PLB
+ * To check whether the core is connected directly to DCR or BUS
* interface and initialize the tft_access accordingly.
*/
- p = (u32 *)of_get_property(op->dev.of_node, "xlnx,dcr-splb-slave-if", NULL);
- tft_access = p ? *p : 0;
+ of_property_read_u32(op->dev.of_node, "xlnx,dcr-splb-slave-if",
+ &tft_access);
/*
- * Fill the resource structure if its direct PLB interface
+ * Fill the resource structure if its direct BUS interface
* otherwise fill the dcr_host structure.
*/
if (tft_access) {
- drvdata->flags |= PLB_ACCESS_FLAG;
- rc = of_address_to_resource(op->dev.of_node, 0, &res);
- if (rc) {
- dev_err(&op->dev, "invalid address\n");
- goto err;
- }
+ drvdata->flags |= BUS_ACCESS_FLAG;
}
#ifdef CONFIG_PPC_DCR
else {
int start;
- res.start = 0;
start = dcr_resource_start(op->dev.of_node, 0);
drvdata->dcr_len = dcr_resource_len(op->dev.of_node, 0);
drvdata->dcr_host = dcr_map(op->dev.of_node, start, drvdata->dcr_len);
if (!DCR_MAP_OK(drvdata->dcr_host)) {
dev_err(&op->dev, "invalid DCR address\n");
- goto err;
+ kfree(drvdata);
+ return -ENODEV;
}
}
#endif
pdata.rotate_screen = 1;
dev_set_drvdata(&op->dev, drvdata);
- return xilinxfb_assign(&op->dev, drvdata, res.start, &pdata);
-
- err:
- kfree(drvdata);
- return -ENODEV;
+ return xilinxfb_assign(op, drvdata, &pdata);
}
static int xilinxfb_of_remove(struct platform_device *op)