atmel: move ATMEL_MAX_UART to platform_data/atmel.h

[firefly-linux-kernel-4.4.55.git] / include / linux / platform_data / atmel.h

diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h
index b0f2c56a8ea26c454f3d8cc71661821ec87f38de..6a293b7fff3bf9d4cb260d3d6c6d639427f38275 100644 (file)
--- a/include/linux/platform_data/atmel.h
+++ b/include/linux/platform_data/atmel.h
@@ -8,6 +8,55 @@
 #define __ATMEL_H__
 
 #include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/leds.h>
+#include <linux/spi/spi.h>
+#include <linux/usb/atmel_usba_udc.h>
+#include <linux/atmel-mci.h>
+#include <sound/atmel-ac97c.h>
+#include <linux/serial.h>
+#include <linux/platform_data/macb.h>
+
+/*
+ * at91: 6 USARTs and one DBGU port (SAM9260)
+ * avr32: 4
+ */
+#define ATMEL_MAX_UART 7
+
+ /* USB Device */
+struct at91_udc_data {
+       int     vbus_pin;               /* high == host powering us */
+       u8      vbus_active_low;        /* vbus polarity */
+       u8      vbus_polled;            /* Use polling, not interrupt */
+       int     pullup_pin;             /* active == D+ pulled up */
+       u8      pullup_active_low;      /* true == pullup_pin is active low */
+};
+
+ /* Compact Flash */
+struct at91_cf_data {
+       int     irq_pin;                /* I/O IRQ */
+       int     det_pin;                /* Card detect */
+       int     vcc_pin;                /* power switching */
+       int     rst_pin;                /* card reset */
+       u8      chipselect;             /* EBI Chip Select number */
+       u8      flags;
+#define AT91_CF_TRUE_IDE       0x01
+#define AT91_IDE_SWAP_A0_A2    0x02
+};
+
+ /* USB Host */
+#define AT91_MAX_USBH_PORTS    3
+struct at91_usbh_data {
+       int             vbus_pin[AT91_MAX_USBH_PORTS];  /* port power-control pin */
+       int             overcurrent_pin[AT91_MAX_USBH_PORTS];
+       u8              ports;                          /* number of ports on root hub */
+       u8              overcurrent_supported;
+       u8              vbus_pin_active_low[AT91_MAX_USBH_PORTS];
+       u8              overcurrent_status[AT91_MAX_USBH_PORTS];
+       u8              overcurrent_changed[AT91_MAX_USBH_PORTS];
+};
 
  /* NAND / SmartMedia */
 struct atmel_nand_data {
@@ -24,4 +73,28 @@ struct atmel_nand_data {
        unsigned int    num_parts;
 };
 
+ /* Serial */
+struct atmel_uart_data {
+       int                     num;            /* port num */
+       short                   use_dma_tx;     /* use transmit DMA? */
+       short                   use_dma_rx;     /* use receive DMA? */
+       void __iomem            *regs;          /* virt. base address, if any */
+       struct serial_rs485     rs485;          /* rs485 settings */
+};
+
+ /* Touchscreen Controller */
+struct at91_tsadcc_data {
+       unsigned int    adc_clock;
+       u8              pendet_debounce;
+       u8              ts_sample_hold_time;
+};
+
+/* CAN */
+struct at91_can_data {
+       void (*transceiver_switch)(int on);
+};
+
+/* FIXME: this needs a better location, but gets stuff building again */
+extern int at91_suspend_entering_slow_clock(void);
+
 #endif /* __ATMEL_H__ */