* that it is only ever disabled for station mode.
* @BSS_CHANGED_IDLE: Idle changed for this BSS/interface.
* @BSS_CHANGED_SSID: SSID changed for this BSS (AP mode)
+ * @BSS_CHANGED_AP_PROBE_RESP: Probe Response changed for this BSS (AP mode)
*/
enum ieee80211_bss_change {
BSS_CHANGED_ASSOC = 1<<0,
BSS_CHANGED_QOS = 1<<13,
BSS_CHANGED_IDLE = 1<<14,
BSS_CHANGED_SSID = 1<<15,
+ BSS_CHANGED_AP_PROBE_RESP = 1<<16,
/* when adding here, make sure to change ieee80211_reconfig */
};
* valid in station mode only while @assoc is true and if also
* requested by %IEEE80211_HW_NEED_DTIM_PERIOD (cf. also hw conf
* @ps_dtim_period)
- * @timestamp: beacon timestamp
+ * @last_tsf: last beacon's/probe response's TSF timestamp (could be old
+ * as it may have been received during scanning long ago)
* @beacon_int: beacon interval
* @assoc_capability: capabilities taken from assoc resp
* @basic_rates: bitmap of basic rates, each bit stands for an
u8 dtim_period;
u16 beacon_int;
u16 assoc_capability;
- u64 timestamp;
+ u64 last_tsf;
u32 basic_rates;
int mcast_rate[IEEE80211_NUM_BANDS];
u16 ht_operation_mode;
* used to indicate that a frame was already retried due to PS
* @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211,
* used to indicate frame should not be encrypted
- * @IEEE80211_TX_CTL_POLL_RESPONSE: This frame is a response to a poll
- * frame (PS-Poll or uAPSD) and should be sent although the station
- * is in powersave mode.
+ * @IEEE80211_TX_CTL_NO_PS_BUFFER: This frame is a response to a poll
+ * frame (PS-Poll or uAPSD) or a non-bufferable MMPDU and must
+ * be sent although the station is in powersave mode.
* @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the
* transmit function after the current frame, this can be used
* by drivers to kick the DMA queue only if unset or when the
IEEE80211_TX_INTFL_NEED_TXPROCESSING = BIT(14),
IEEE80211_TX_INTFL_RETRIED = BIT(15),
IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16),
- IEEE80211_TX_CTL_POLL_RESPONSE = BIT(17),
+ IEEE80211_TX_CTL_NO_PS_BUFFER = BIT(17),
IEEE80211_TX_CTL_MORE_FRAMES = BIT(18),
IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19),
/* hole at 20, use later */
IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU | \
IEEE80211_TX_STAT_TX_FILTERED | IEEE80211_TX_STAT_ACK | \
IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK | \
- IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_POLL_RESPONSE | \
+ IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_NO_PS_BUFFER | \
IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC | \
IEEE80211_TX_CTL_STBC | IEEE80211_TX_STATUS_EOSP)
* @flags: transmit info flags, defined above
* @band: the band to transmit on (use for checking for races)
* @antenna_sel_tx: antenna to use, 0 for automatic diversity
- * @pad: padding, ignore
+ * @ack_frame_id: internal frame ID for TX status, used internally
* @control: union for control data
* @status: union for status data
* @driver_data: array of driver_data pointers
u8 antenna_sel_tx;
- /* 2 byte hole */
- u8 pad[2];
+ u16 ack_frame_id;
union {
struct {
* @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index
* @RX_FLAG_40MHZ: HT40 (40 MHz) was used
* @RX_FLAG_SHORT_GI: Short guard interval was used
+ * @RX_FLAG_NO_SIGNAL_VAL: The signal strength value is not present.
+ * Valid only for data frames (mainly A-MPDU)
*/
enum mac80211_rx_flags {
RX_FLAG_MMIC_ERROR = 1<<0,
RX_FLAG_HT = 1<<9,
RX_FLAG_40MHZ = 1<<10,
RX_FLAG_SHORT_GI = 1<<11,
+ RX_FLAG_NO_SIGNAL_VAL = 1<<12,
};
/**
u8 count;
};
+/**
+ * enum ieee80211_vif_flags - virtual interface flags
+ *
+ * @IEEE80211_VIF_BEACON_FILTER: the device performs beacon filtering
+ * on this virtual interface to avoid unnecessary CPU wakeups
+ * @IEEE80211_VIF_SUPPORTS_CQM_RSSI: the device can do connection quality
+ * monitoring on this virtual interface -- i.e. it can monitor
+ * connection quality related parameters, such as the RSSI level and
+ * provide notifications if configured trigger levels are reached.
+ */
+enum ieee80211_vif_flags {
+ IEEE80211_VIF_BEACON_FILTER = BIT(0),
+ IEEE80211_VIF_SUPPORTS_CQM_RSSI = BIT(1),
+};
+
/**
* struct ieee80211_vif - per-interface data
*
* @addr: address of this interface
* @p2p: indicates whether this AP or STA interface is a p2p
* interface, i.e. a GO or p2p-sta respectively
+ * @driver_flags: flags/capabilities the driver has for this interface,
+ * these need to be set (or cleared) when the interface is added
+ * or, if supported by the driver, the interface type is changed
+ * at runtime, mac80211 will never touch this field
* @drv_priv: data area for driver use, will always be aligned to
* sizeof(void *).
*/
struct ieee80211_bss_conf bss_conf;
u8 addr[ETH_ALEN];
bool p2p;
+ u32 driver_flags;
/* must be last */
u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};
* @IEEE80211_KEY_FLAG_SW_MGMT: This flag should be set by the driver for a
* CCMP key if it requires CCMP encryption of management frames (MFP) to
* be done in software.
+ * @IEEE80211_KEY_FLAG_PUT_IV_SPACE: This flag should be set by the driver
+ * for a CCMP key if space should be prepared for the IV, but the IV
+ * itself should not be generated. Do not set together with
+ * @IEEE80211_KEY_FLAG_GENERATE_IV on the same key.
*/
enum ieee80211_key_flags {
IEEE80211_KEY_FLAG_WMM_STA = 1<<0,
IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
IEEE80211_KEY_FLAG_PAIRWISE = 1<<3,
IEEE80211_KEY_FLAG_SW_MGMT = 1<<4,
+ IEEE80211_KEY_FLAG_PUT_IV_SPACE = 1<<5,
};
/**
SET_KEY, DISABLE_KEY,
};
+/**
+ * enum ieee80211_sta_state - station state
+ *
+ * @IEEE80211_STA_NOTEXIST: station doesn't exist at all,
+ * this is a special state for add/remove transitions
+ * @IEEE80211_STA_NONE: station exists without special state
+ * @IEEE80211_STA_AUTH: station is authenticated
+ * @IEEE80211_STA_ASSOC: station is associated
+ * @IEEE80211_STA_AUTHORIZED: station is authorized (802.1X)
+ */
+enum ieee80211_sta_state {
+ /* NOTE: These need to be ordered correctly! */
+ IEEE80211_STA_NOTEXIST,
+ IEEE80211_STA_NONE,
+ IEEE80211_STA_AUTH,
+ IEEE80211_STA_ASSOC,
+ IEEE80211_STA_AUTHORIZED,
+};
+
/**
* struct ieee80211_sta - station table entry
*
* @IEEE80211_HW_MFP_CAPABLE:
* Hardware supports management frame protection (MFP, IEEE 802.11w).
*
- * @IEEE80211_HW_BEACON_FILTER:
- * Hardware supports dropping of irrelevant beacon frames to
- * avoid waking up cpu.
- *
* @IEEE80211_HW_SUPPORTS_STATIC_SMPS:
* Hardware supports static spatial multiplexing powersave,
* ie. can turn off all but one chain even on HT connections
* When this flag is set, signaling beacon-loss will cause an immediate
* change to disassociated state.
*
- * @IEEE80211_HW_SUPPORTS_CQM_RSSI:
- * Hardware can do connection quality monitoring - i.e. it can monitor
- * connection quality related parameters, such as the RSSI level and
- * provide notifications if configured trigger levels are reached.
- *
* @IEEE80211_HW_NEED_DTIM_PERIOD:
* This device needs to know the DTIM period for the BSS before
* associating.
* @IEEE80211_HW_TX_AMPDU_SETUP_IN_HW: The device handles TX A-MPDU session
* setup strictly in HW. mac80211 should not attempt to do this in
* software.
+ *
+ * @IEEE80211_HW_SCAN_WHILE_IDLE: The device can do hw scan while
+ * being idle (i.e. mac80211 doesn't have to go idle-off during the
+ * the scan).
*/
enum ieee80211_hw_flags {
IEEE80211_HW_HAS_RATE_CONTROL = 1<<0,
IEEE80211_HW_PS_NULLFUNC_STACK = 1<<11,
IEEE80211_HW_SUPPORTS_DYNAMIC_PS = 1<<12,
IEEE80211_HW_MFP_CAPABLE = 1<<13,
- IEEE80211_HW_BEACON_FILTER = 1<<14,
+ /* reuse bit 14 */
IEEE80211_HW_SUPPORTS_STATIC_SMPS = 1<<15,
IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS = 1<<16,
IEEE80211_HW_SUPPORTS_UAPSD = 1<<17,
IEEE80211_HW_REPORTS_TX_ACK_STATUS = 1<<18,
IEEE80211_HW_CONNECTION_MONITOR = 1<<19,
- IEEE80211_HW_SUPPORTS_CQM_RSSI = 1<<20,
+ /* reuse bit 20 */
IEEE80211_HW_SUPPORTS_PER_STA_GTK = 1<<21,
IEEE80211_HW_AP_LINK_PS = 1<<22,
IEEE80211_HW_TX_AMPDU_SETUP_IN_HW = 1<<23,
+ IEEE80211_HW_SCAN_WHILE_IDLE = 1<<24,
};
/**
return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx];
}
+/**
+ * ieee80211_free_txskb - free TX skb
+ * @hw: the hardware
+ * @skb: the skb
+ *
+ * Free a transmit skb. Use this funtion when some failure
+ * to transmit happened and thus status cannot be reported.
+ */
+void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb);
+
/**
* DOC: Hardware crypto acceleration
*
* DOC: Beacon filter support
*
* Some hardware have beacon filter support to reduce host cpu wakeups
- * which will reduce system power consumption. It usuallly works so that
+ * which will reduce system power consumption. It usually works so that
* the firmware creates a checksum of the beacon but omits all constantly
* changing elements (TSF, TIM etc). Whenever the checksum changes the
* beacon is forwarded to the host, otherwise it will be just dropped. That
* way the host will only receive beacons where some relevant information
* (for example ERP protection or WMM settings) have changed.
*
- * Beacon filter support is advertised with the %IEEE80211_HW_BEACON_FILTER
- * hardware capability. The driver needs to enable beacon filter support
+ * Beacon filter support is advertised with the %IEEE80211_VIF_BEACON_FILTER
+ * interface capability. The driver needs to enable beacon filter support
* whenever power save is enabled, that is %IEEE80211_CONF_PS is set. When
* power save is enabled, the stack will not check for beacon loss and the
* driver needs to notify about loss of beacons with ieee80211_beacon_loss().
* the station sends a PS-Poll or a uAPSD trigger frame, mac80211
* will inform the driver of this with the @allow_buffered_frames
* callback; this callback is optional. mac80211 will then transmit
- * the frames as usual and set the %IEEE80211_TX_CTL_POLL_RESPONSE
+ * the frames as usual and set the %IEEE80211_TX_CTL_NO_PS_BUFFER
* on each frame. The last frame in the service period (or the only
* response to a PS-Poll) also has %IEEE80211_TX_STATUS_EOSP set to
* indicate that it ends the service period; as this frame must have
* When TX status is reported for this frame, the service period is
* marked has having ended and a new one can be started by the peer.
*
+ * Additionally, non-bufferable MMPDUs can also be transmitted by
+ * mac80211 with the %IEEE80211_TX_CTL_NO_PS_BUFFER set in them.
+ *
* Another race condition can happen on some devices like iwlwifi
* when there are frames queued for the station and it wakes up
* or polls; the frames that are already queued could end up being
IEEE80211_AMPDU_TX_OPERATIONAL,
};
-/**
- * enum ieee80211_tx_sync_type - TX sync type
- * @IEEE80211_TX_SYNC_AUTH: sync TX for authentication
- * (and possibly also before direct probe)
- * @IEEE80211_TX_SYNC_ASSOC: sync TX for association
- * @IEEE80211_TX_SYNC_ACTION: sync TX for action frame
- * (not implemented yet)
- */
-enum ieee80211_tx_sync_type {
- IEEE80211_TX_SYNC_AUTH,
- IEEE80211_TX_SYNC_ASSOC,
- IEEE80211_TX_SYNC_ACTION,
-};
-
/**
* enum ieee80211_frame_release_type - frame release reason
* @IEEE80211_FRAME_RELEASE_PSPOLL: frame released for PS-Poll
* skb contains the buffer starting from the IEEE 802.11 header.
* The low-level driver should send the frame out based on
* configuration in the TX control data. This handler should,
- * preferably, never fail and stop queues appropriately, more
- * importantly, however, it must never fail for A-MPDU-queues.
- * This function should return NETDEV_TX_OK except in very
- * limited cases.
- * Must be implemented and atomic.
+ * preferably, never fail and stop queues appropriately.
+ * This must be implemented if @tx_frags is not.
+ * Must be atomic.
+ *
+ * @tx_frags: Called to transmit multiple fragments of a single MSDU.
+ * This handler must consume all fragments, sending out some of
+ * them only is useless and it can't ask for some of them to be
+ * queued again. If the frame is not fragmented the queue has a
+ * single SKB only. To avoid issues with the networking stack
+ * when TX status is reported the frames should be removed from
+ * the skb queue.
+ * If this is used, the tx_info @vif and @sta pointers will be
+ * invalid -- you must not use them in that case.
+ * This must be implemented if @tx isn't.
+ * Must be atomic.
*
* @start: Called before the first netdevice attached to the hardware
* is enabled. This should turn on the hardware and must turn on
* of the bss parameters has changed when a call is made. The callback
* can sleep.
*
- * @tx_sync: Called before a frame is sent to an AP/GO. In the GO case, the
- * driver should sync with the GO's powersaving so the device doesn't
- * transmit the frame while the GO is asleep. In the regular AP case
- * it may be used by drivers for devices implementing other restrictions
- * on talking to APs, e.g. due to regulatory enforcement or just HW
- * restrictions.
- * This function is called for every authentication, association and
- * action frame separately since applications might attempt to auth
- * with multiple APs before chosing one to associate to. If it returns
- * an error, the corresponding authentication, association or frame
- * transmission is aborted and reported as having failed. It is always
- * called after tuning to the correct channel.
- * The callback might be called multiple times before @finish_tx_sync
- * (but @finish_tx_sync will be called once for each) but in practice
- * this is unlikely to happen. It can also refuse in that case if the
- * driver cannot handle that situation.
- * This callback can sleep.
- * @finish_tx_sync: Called as a counterpart to @tx_sync, unless that returned
- * an error. This callback can sleep.
- *
* @prepare_multicast: Prepare for multicast filter configuration.
* This callback is optional, and its return value is passed
* to configure_filter(). This callback must be atomic.
* in AP mode, this callback will not be called when the flag
* %IEEE80211_HW_AP_LINK_PS is set. Must be atomic.
*
+ * @sta_state: Notifies low level driver about state transition of a
+ * station (which can be the AP, a client, IBSS/WDS/mesh peer etc.)
+ * This callback is mutually exclusive with @sta_add/@sta_remove.
+ * It must not fail for down transitions but may fail for transitions
+ * up the list of states.
+ * The callback can sleep.
+ *
* @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
* bursting) for a hardware TX queue.
* Returns a negative error code on failure.
* @allow_buffered_frames: Prepare device to allow the given number of frames
* to go out to the given station. The frames will be sent by mac80211
* via the usual TX path after this call. The TX information for frames
- * released will also have the %IEEE80211_TX_CTL_POLL_RESPONSE flag set
+ * released will also have the %IEEE80211_TX_CTL_NO_PS_BUFFER flag set
* and the last one will also have %IEEE80211_TX_STATUS_EOSP set. In case
* frames from multiple TIDs are released and the driver might reorder
* them between the TIDs, it must set the %IEEE80211_TX_STATUS_EOSP flag
*/
struct ieee80211_ops {
void (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb);
+ void (*tx_frags)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+ struct ieee80211_sta *sta, struct sk_buff_head *skbs);
int (*start)(struct ieee80211_hw *hw);
void (*stop)(struct ieee80211_hw *hw);
#ifdef CONFIG_PM
struct ieee80211_bss_conf *info,
u32 changed);
- int (*tx_sync)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
- const u8 *bssid, enum ieee80211_tx_sync_type type);
- void (*finish_tx_sync)(struct ieee80211_hw *hw,
- struct ieee80211_vif *vif,
- const u8 *bssid,
- enum ieee80211_tx_sync_type type);
-
u64 (*prepare_multicast)(struct ieee80211_hw *hw,
struct netdev_hw_addr_list *mc_list);
void (*configure_filter)(struct ieee80211_hw *hw,
struct ieee80211_sta *sta);
void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
enum sta_notify_cmd, struct ieee80211_sta *sta);
+ int (*sta_state)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+ struct ieee80211_sta *sta,
+ enum ieee80211_sta_state old_state,
+ enum ieee80211_sta_state new_state);
int (*conf_tx)(struct ieee80211_hw *hw,
struct ieee80211_vif *vif, u16 queue,
const struct ieee80211_tx_queue_params *params);
return ieee80211_beacon_get_tim(hw, vif, NULL, NULL);
}
+/**
+ * ieee80211_proberesp_get - retrieve a Probe Response template
+ * @hw: pointer obtained from ieee80211_alloc_hw().
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * Creates a Probe Response template which can, for example, be uploaded to
+ * hardware. The destination address should be set by the caller.
+ *
+ * Can only be called in AP mode.
+ */
+struct sk_buff *ieee80211_proberesp_get(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif);
+
/**
* ieee80211_pspoll_get - retrieve a PS Poll template
* @hw: pointer obtained from ieee80211_alloc_hw().
*
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
*
- * When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTER and
+ * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER and
* %IEEE80211_CONF_PS is set, the driver needs to inform whenever the
* hardware is not receiving beacons with this function.
*/
*
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
*
- * When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTER, and
+ * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER, and
* %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver
* needs to inform if the connection to the AP has been lost.
*
* @rssi_event: the RSSI trigger event type
* @gfp: context flags
*
- * When the %IEEE80211_HW_SUPPORTS_CQM_RSSI is set, and a connection quality
+ * When the %IEEE80211_VIF_SUPPORTS_CQM_RSSI is set, and a connection quality
* monitoring is configured with an rssi threshold, the driver will inform
* whenever the rssi level reaches the threshold.
*/
*
* @IEEE80211_RC_HT_CHANGED: The HT parameters of the operating channel have
* changed, rate control algorithm can update its internal state if needed.
+ * @IEEE80211_RC_SMPS_CHANGED: The SMPS state of the station changed, the rate
+ * control algorithm needs to adjust accordingly.
*/
enum rate_control_changed {
- IEEE80211_RC_HT_CHANGED = BIT(0)
+ IEEE80211_RC_HT_CHANGED = BIT(0),
+ IEEE80211_RC_SMPS_CHANGED = BIT(1),
};
/**
* @hw: The hardware the algorithm is invoked for.
* @sband: The band this frame is being transmitted on.
* @bss_conf: the current BSS configuration
+ * @skb: the skb that will be transmitted, the control information in it needs
+ * to be filled in
* @reported_rate: The rate control algorithm can fill this in to indicate
* which rate should be reported to userspace as the current rate and
* used for rate calculations in the mesh network.
* RTS threshold
* @short_preamble: whether mac80211 will request short-preamble transmission
* if the selected rate supports it
- * @max_rate_idx: user-requested maximum rate (not MCS for now)
+ * @max_rate_idx: user-requested maximum (legacy) rate
* (deprecated; this will be removed once drivers get updated to use
* rate_idx_mask)
- * @rate_idx_mask: user-requested rate mask (not MCS for now)
- * @skb: the skb that will be transmitted, the control information in it needs
- * to be filled in
+ * @rate_idx_mask: user-requested (legacy) rate mask
+ * @rate_idx_mcs_mask: user-requested MCS rate mask
* @bss: whether this frame is sent out in AP or IBSS mode
*/
struct ieee80211_tx_rate_control {
bool rts, short_preamble;
u8 max_rate_idx;
u32 rate_idx_mask;
+ u8 rate_idx_mcs_mask[IEEE80211_HT_MCS_MASK_LEN];
bool bss;
};
return i;
/* warn when we cannot find a rate. */
- WARN_ON(1);
+ WARN_ON_ONCE(1);
+ /* and return 0 (the lowest index) */
return 0;
}
projects / firefly-linux-kernel-4.4.55.git / blobdiff