X-Git-Url: http://demsky.eecs.uci.edu/git/?a=blobdiff_plain;f=arch%2Farm%2Fmach-sa1100%2Fassabet.c;h=e2d411a8d4ce36db54246cfc48819a263b0a67c8;hb=374da9da22ebaad0524c77905b5e89ae4619bef3;hp=0c4b76ab4d8eba0037e305d5d8f9b17b36074fa7;hpb=f94f72ee673edd6cd9cd36fd954173871808873f;p=firefly-linux-kernel-4.4.55.git

diff --git a/arch/arm/mach-sa1100/assabet.c b/arch/arm/mach-sa1100/assabet.c
index 0c4b76ab4d8e..e2d411a8d4ce 100644
--- a/arch/arm/mach-sa1100/assabet.c
+++ b/arch/arm/mach-sa1100/assabet.c
@@ -40,13 +40,13 @@
 #include "generic.h"
 
 #define ASSABET_BCR_DB1110 \
-	(ASSABET_BCR_SPK_OFF    | ASSABET_BCR_QMUTE     | \
+	(ASSABET_BCR_SPK_OFF    | \
 	 ASSABET_BCR_LED_GREEN  | ASSABET_BCR_LED_RED   | \
 	 ASSABET_BCR_RS232EN    | ASSABET_BCR_LCD_12RGB | \
 	 ASSABET_BCR_IRDA_MD0)
 
 #define ASSABET_BCR_DB1111 \
-	(ASSABET_BCR_SPK_OFF    | ASSABET_BCR_QMUTE     | \
+	(ASSABET_BCR_SPK_OFF    | \
 	 ASSABET_BCR_LED_GREEN  | ASSABET_BCR_LED_RED   | \
 	 ASSABET_BCR_RS232EN    | ASSABET_BCR_LCD_12RGB | \
 	 ASSABET_BCR_CF_BUS_OFF | ASSABET_BCR_STEREO_LB | \
@@ -152,15 +152,8 @@ static struct flash_platform_data assabet_flash_data = {
 };
 
 static struct resource assabet_flash_resources[] = {
-	{
-		.start	= SA1100_CS0_PHYS,
-		.end	= SA1100_CS0_PHYS + SZ_32M - 1,
-		.flags	= IORESOURCE_MEM,
-	}, {
-		.start	= SA1100_CS1_PHYS,
-		.end	= SA1100_CS1_PHYS + SZ_32M - 1,
-		.flags	= IORESOURCE_MEM,
-	}
+	DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_32M),
+	DEFINE_RES_MEM(SA1100_CS1_PHYS, SZ_32M),
 };
 
 
@@ -204,13 +197,22 @@ static struct mcp_plat_data assabet_mcp_data = {
 	.sclk_rate	= 11981000,
 };
 
+#ifdef CONFIG_ASSABET_NEPONSET
+static struct resource neponset_resources[] = {
+	DEFINE_RES_MEM(0x10000000, 0x08000000),
+	DEFINE_RES_MEM(0x18000000, 0x04000000),
+	DEFINE_RES_MEM(0x40000000, SZ_8K),
+	DEFINE_RES_IRQ(IRQ_GPIO25),
+};
+#endif
+
 static void __init assabet_init(void)
 {
 	/*
 	 * Ensure that the power supply is in "high power" mode.
 	 */
-	GPDR |= GPIO_GPIO16;
 	GPSR = GPIO_GPIO16;
+	GPDR |= GPIO_GPIO16;
 
 	/*
 	 * Ensure that these pins are set as outputs and are driving
@@ -218,8 +220,16 @@ static void __init assabet_init(void)
 	 * the WS latch in the CPLD, and we don't float causing
 	 * excessive power drain.  --rmk
 	 */
-	GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
 	GPCR = GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
+	GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
+
+	/*
+	 * Also set GPIO27 as an output; this is used to clock UART3
+	 * via the FPGA and as otherwise has no pullups or pulldowns,
+	 * so stop it floating.
+	 */
+	GPCR = GPIO_GPIO27;
+	GPDR |= GPIO_GPIO27;
 
 	/*
 	 * Set up registers for sleep mode.
@@ -246,6 +256,9 @@ static void __init assabet_init(void)
 #ifndef CONFIG_ASSABET_NEPONSET
 		printk( "Warning: Neponset detected but full support "
 			"hasn't been configured in the kernel\n" );
+#else
+		platform_device_register_simple("neponset", 0,
+			neponset_resources, ARRAY_SIZE(neponset_resources));
 #endif
 	}
 
@@ -412,21 +425,8 @@ static void __init assabet_map_io(void)
 	 */
 	Ser1SDCR0 |= SDCR0_SUS;
 
-	if (machine_has_neponset()) {
-#ifdef CONFIG_ASSABET_NEPONSET
-		extern void neponset_map_io(void);
-
-		/*
-		 * We map Neponset registers even if it isn't present since
-		 * many drivers will try to probe their stuff (and fail).
-		 * This is still more friendly than a kernel paging request
-		 * crash.
-		 */
-		neponset_map_io();
-#endif
-	} else {
+	if (!machine_has_neponset())
 		sa1100_register_uart_fns(&assabet_port_fns);
-	}
 
 	/*
 	 * When Neponset is attached, the first UART should be