ARM: ux500: fix MMC/SD card regression

Ux500 is regressing due to commit
a21763a0b1e5a5ab8310f581886d04beadc16616
"pinctrl: nomadik: activate strict mux mode" which disallows
Nomadik GPIO 5 to be muxed in as a level shifter voltage select
pin, as it is currently described as being used for RX on UART1.

The behaviour is correct, instead the hardware config has been
incorrecly specified: UART1 is indeed unused on HREFv60plus and
Snowball and that is why HREFv60plus can use the pins it would
normally occupy as the voltage select line for the MMC/SD
levelshifter (Snowball uses it for I2C4).

The reason UART1 was anyway enabled on these platforms was
probably to secure the port enumeration to userspace. This
can be solved by using aliases (done in a separate patch) so
we can now deactivate UART1 and let MMC/SD use it properly
on HREFv60plus. We explicitly activate it only for the
older HREFprev60 board.

To complete, we set up the pin configuration for these pins
properly in the sdi0 node.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 744c1e3a744df1530ba53cd2a56029a9e9ac5d37..6d8ce154347e7a9a78d02e0c06701a02fc02a4ad 100644 (file)
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -32,11 +32,11 @@
                        status = "okay";
                };
 
                        status = "okay";
                };
 

+               /* This UART is unused and thus left disabled */

                uart@80121000 {
                        pinctrl-names = "default", "sleep";
                        pinctrl-0 = <&uart1_default_mode>;
                        pinctrl-1 = <&uart1_sleep_mode>;
                uart@80121000 {
                        pinctrl-names = "default", "sleep";
                        pinctrl-0 = <&uart1_default_mode>;
                        pinctrl-1 = <&uart1_sleep_mode>;

-                       status = "okay";

                };
 
                uart@80007000 {
                };
 
                uart@80007000 {

diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi
index 7f3975b58d16607d5cf79f10eca8df1dc75ab9d5..b0278f4c486cefa6f3363f91fd3f312bfc87015f 100644 (file)
--- a/arch/arm/boot/dts/ste-hrefprev60.dtsi
+++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi
@@ -23,6 +23,11 @@
        };
 
        soc {
        };
 
        soc {

+               /* Enable UART1 on this board */
+               uart@80121000 {
+                       status = "okay";
+               };
+

                i2c@80004000 {
                        tps61052@33 {
                                compatible = "tps61052";
                i2c@80004000 {
                        tps61052@33 {
                                compatible = "tps61052";

diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
index a4bc9e77d640d3762b01952ca23ae07d558cab36..810cda743b6d56ae19118260367f986dcee690af 100644 (file)
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -43,15 +43,26 @@
                                  <&vaudio_hf_hrefv60_mode>,
                                  <&gbf_hrefv60_mode>,
                                  <&hdtv_hrefv60_mode>,
                                  <&vaudio_hf_hrefv60_mode>,
                                  <&gbf_hrefv60_mode>,
                                  <&hdtv_hrefv60_mode>,

-                                 <&touch_hrefv60_mode>;
+                                 <&touch_hrefv60_mode>,
+                                 <&gpios_hrefv60_mode>;

 
                        sdi0 {
 
                        sdi0 {

-                               /* SD card detect GPIO pin, extend default state */

                                sdi0_default_mode: sdi0_default {
                                sdi0_default_mode: sdi0_default {

+                                       /* SD card detect GPIO pin, extend default state */

                                        default_hrefv60_cfg1 {
                                                pins = "GPIO95_E8";
                                                ste,config = <&gpio_in_pu>;
                                        };
                                        default_hrefv60_cfg1 {
                                                pins = "GPIO95_E8";
                                                ste,config = <&gpio_in_pu>;
                                        };

+                                       /* VMMCI level-shifter enable */
+                                       default_hrefv60_cfg2 {
+                                               pins = "GPIO169_D22";
+                                               ste,config = <&gpio_out_lo>;
+                                       };
+                                       /* VMMCI level-shifter voltage select */
+                                       default_hrefv60_cfg3 {
+                                               pins = "GPIO5_AG6";
+                                               ste,config = <&gpio_out_hi>;
+                                       };

                                };
                        };
                        ipgpio {
                                };
                        };
                        ipgpio {


@@ -213,6 +224,16 @@
                                        };
                                };
                        };
                                        };
                                };
                        };

+                       gpios {
+                               /* Dangling GPIO pins */
+                               gpios_hrefv60_mode: gpios_hrefv60 {
+                                       default_cfg1 {
+                                               /* Normally UART1 RXD, now dangling */
+                                               pins = "GPIO4_AH6";
+                                               ste,config = <&in_pu>;
+                                       };
+                               };
+                       };

                };
        };
 };
                };
        };
 };

diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index acf14cebef81bf7be60157a1f4e9af4707ef59cc..32a5ccb14e7ebfbaec118ceed1f3bc14c2b646df 100644 (file)
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -230,11 +230,11 @@
                        status = "okay";
                };
 
                        status = "okay";
                };
 

+               /* This UART is unused and thus left disabled */

                uart@80121000 {
                        pinctrl-names = "default", "sleep";
                        pinctrl-0 = <&uart1_default_mode>;
                        pinctrl-1 = <&uart1_sleep_mode>;
                uart@80121000 {
                        pinctrl-names = "default", "sleep";
                        pinctrl-0 = <&uart1_default_mode>;
                        pinctrl-1 = <&uart1_sleep_mode>;

-                       status = "okay";

                };
 
                uart@80007000 {
                };
 
                uart@80007000 {


@@ -459,7 +459,21 @@
                                                pins = "GPIO21_AB3"; /* DAT31DIR */
                                                ste,config = <&out_hi>;
                                        };
                                                pins = "GPIO21_AB3"; /* DAT31DIR */
                                                ste,config = <&out_hi>;
                                        };

-
+                                       /* SD card detect GPIO pin, extend default state */
+                                       snowball_cfg2 {
+                                               pins = "GPIO218_AH11";
+                                               ste,config = <&gpio_in_pu>;
+                                       };
+                                       /* VMMCI level-shifter enable */
+                                       snowball_cfg3 {
+                                               pins = "GPIO217_AH12";
+                                               ste,config = <&gpio_out_lo>;
+                                       };
+                                       /* VMMCI level-shifter voltage select */
+                                       snowball_cfg4 {
+                                               pins = "GPIO228_AJ6";
+                                               ste,config = <&gpio_out_hi>;
+                                       };

                                };
                        };
                        ssp0 {
                                };
                        };
                        ssp0 {