-#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */
-#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
-#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
-#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
-#define UART_FCR_TRIGGER_MASK 0xF0 /* Mask for the FIFO trigger range */
-#define UART_FCR_R_TRIGGER_1 0x00 /* Mask for receive trigger set at 1 */
-#define UART_FCR_R_TRIGGER_4 0x40 /* Mask for receive trigger set at 4 */
-#define UART_FCR_R_TRIGGER_8 0x80 /* Mask for receive trigger set at 8 */
-#define UART_FCR_R_TRIGGER_14 0xA0 /* Mask for receive trigger set at 14 */
-#define UART_FCR_T_TRIGGER_0 0x00 /* Mask for transmit trigger set at 0 */
-#define UART_FCR_T_TRIGGER_4 0x10 /* Mask for transmit trigger set at 4 */
-#define UART_FCR_T_TRIGGER_8 0x20 /* Mask for transmit trigger set at 8 */
-#define UART_FCR_T_TRIGGER_12 0x30 /* Mask for transmit trigger set at 12 */
-
-/*
- * These are the definitions for the Line Control Register
- */
-#define UART_LCR_SBC 0x40 /* Set break control */
-#define UART_LCR_SPAR 0x20 /* Stick parity (?) */
-#define UART_LCR_EPAR 0x10 /* Even parity select */
-#define UART_LCR_PARITY 0x08 /* Parity Enable */
-#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */
-#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */
-#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */
-#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */
-#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */
-
-/*
- * These are the definitions for the Line Status Register
- */
-#define UART_LSR_TEMT 0x40 /* Transmitter empty */
-#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */
-#define UART_LSR_BI 0x10 /* Break interrupt indicator */
-#define UART_LSR_FE 0x08 /* Frame error indicator */
-#define UART_LSR_PE 0x04 /* Parity error indicator */
-#define UART_LSR_OE 0x02 /* Overrun error indicator */
-#define UART_LSR_DR 0x01 /* Receiver data ready */
-
-/*
- * These are the definitions for the Interrupt Identification Register
- */
-#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
-#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
-#define UART_IIR_MSI 0x00 /* Modem status interrupt */
-#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
-#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
-#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
-
-/*
- * These are the definitions for the Interrupt Enable Register
- */
-#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
-#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
-#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
-#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */
-
-/*
- * These are the definitions for the Modem Control Register
- */
-#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
-#define UART_MCR_OUT2 0x08 /* Out2 complement */
-#define UART_MCR_OUT1 0x04 /* Out1 complement */
-#define UART_MCR_RTS 0x02 /* RTS complement */
-#define UART_MCR_DTR 0x01 /* DTR complement */
-
-/*
- * These are the definitions for the Modem Status Register
- */
-#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
-#define UART_MSR_RI 0x40 /* Ring Indicator */
-#define UART_MSR_DSR 0x20 /* Data Set Ready */
-#define UART_MSR_CTS 0x10 /* Clear to Send */
-#define UART_MSR_DDCD 0x08 /* Delta DCD */
-#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
-#define UART_MSR_DDSR 0x02 /* Delta DSR */
-#define UART_MSR_DCTS 0x01 /* Delta CTS */
-#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */
-