Correct spelling typo in treewide.
Signed-off-by: Hayato Suzuki <hytszk@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Clock bindings for ARM Integrator Core Module clocks
-Auxilary Oscillator Clock
+Auxiliary Oscillator Clock
This is a configurable clock fed from a 24 MHz chrystal,
used for generating e.g. video clocks. It is located on the
SEC 6 is as Freescale's Cryptographic Accelerator and Assurance Module (CAAM).
-Currently Freescale powerpc chip C29X is embeded with SEC 6.
+Currently Freescale powerpc chip C29X is embedded with SEC 6.
SEC 6 device tree binding include:
-SEC 6 Node
-Job Ring Node
- interrupts: Should contain the interrupt for the device
- clocks: The clock is needed by the ADC controller, ADC clock source is ipg clock.
- clock-names: Must contain "adc", matching entry in the clocks property.
-- vref-supply: The regulator supply ADC refrence voltage.
+- vref-supply: The regulator supply ADC reference voltage.
Example:
adc0: adc@4003b000 {
regulator-ramp-delay for BUCKs = [6250/12500/25000(default)/50000] uV/us
- BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explictly
+ BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explicitly
regulator-ramp-delay = <0> can be used for them to disable ramp delay.
In the absence of the regulator-ramp-delay property, the default ramp
delay will be used.
Other factor which governs the selection of ecc-scheme is oob-size.
Higher ECC schemes require more OOB/Spare area to store ECC syndrome,
so the device should have enough free bytes available its OOB/Spare
- area to accomodate ECC for entire page. In general following expression
- helps in determining if given device can accomodate ECC syndrome:
+ area to accommodate ECC for entire page. In general following expression
+ helps in determining if given device can accommodate ECC syndrome:
"2 + (PAGESIZE / 512) * ECC_BYTES" >= OOBSIZE"
where
OOBSIZE number of bytes in OOB/spare area
Example(b): For a device with PAGESIZE = 2048 and OOBSIZE = 128 and
trying to use BCH16 (ECC_BYTES=26) ecc-scheme.
Number of ECC bytes per page = (2 + (2048 / 512) * 26) = 106 B
- which can be accomodate in the OOB/Spare area of this device
+ which can be accommodated in the OOB/Spare area of this device
(OOBSIZE=128). So this device can use BCH16 ecc-scheme.
- samsung,pbl: Integer, Programmable Burst Length.
Supported values are 1, 2, 4, 8, 16, or 32.
- samsung,burst-map: Integer, Program the possible bursts supported by sxgbe
- This is an interger and represents allowable DMA bursts when fixed burst.
+ This is an integer and represents allowable DMA bursts when fixed burst.
Allowable range is 0x01-0x3F. When this field is set fixed burst is enabled.
When fixed length is needed for burst mode, it can be set within allowable
range.
cfg_offset(bus, device, function, register) =
bus << 16 | device << 11 | function << 8 | register
-Whilst ECAM extends this by 4 bits to accomodate 4k of function space:
+Whilst ECAM extends this by 4 bits to accommodate 4k of function space:
cfg_offset(bus, device, function, register) =
bus << 20 | device << 15 | function << 12 | register
};
That node describes an IP block (PHY provider) that implements 2 different PHYs.
-In order to differentiate between these 2 PHYs, an additonal specifier should be
+In order to differentiate between these 2 PHYs, an additional specifier should be
given while trying to get a reference to it.
PHY user node
- cm-thermal-zone : name of external thermometer's thermal zone
- cm-battery-* : threshold battery temperature for charging
-cold : critical cold temperature of battery for charging
- -cold-in-minus : flag that cold temerature is in minus degree
+ -cold-in-minus : flag that cold temperature is in minus degrees
-hot : critical hot temperature of battery for charging
-temp-diff : temperature difference to allow recharging
- cm-dis/charging-max = limits of charging duration
0: Channel 1
1: Channel 2
2: Channel 3
- If parameter is missing, channel 1 is choosen.
+ If parameter is missing, channel 1 is chosen.
This properties have to be specified as '/bits/ 8' values.
- st,thermal-warning-recover:
toradex Toradex AG
toshiba Toshiba Corporation
toumaz Toumaz
-usi Universal Scientifc Industrial Co., Ltd.
+usi Universal Scientific Industrial Co., Ltd.
v3 V3 Semiconductor
variscite Variscite Ltd.
via VIA Technologies, Inc.
-----------------------------------------------------
Required properties (as per of_videomode_helper):
- - atmel,dmacon: dma controler configuration
- - atmel,lcdcon2: lcd controler configuration
+ - atmel,dmacon: dma controller configuration
+ - atmel,lcdcon2: lcd controller configuration
- atmel,guard-time: lcd guard time (Delay in frame periods)
- bits-per-pixel: lcd panel bit-depth.
register is not modified as recommended by the datasheet.
- fsl,lpccr: Contrast Control Register value. This property provides the
default value for the contrast control register.
- If that property is ommited, the register is zeroed.
+ If that property is omitted, the register is zeroed.
- fsl,lscr1: LCDC Sharp Configuration Register value.
Example:
projects / firefly-linux-kernel-4.4.55.git / commitdiff