mmc: sdhci-esdhc-imx: add imx7d support and support HS400
authorHaibo Chen <haibo.chen@freescale.com>
Tue, 11 Aug 2015 11:38:26 +0000 (19:38 +0800)
committerUlf Hansson <ulf.hansson@linaro.org>
Thu, 27 Aug 2015 12:50:50 +0000 (14:50 +0200)
The imx7d usdhc is derived from imx6sx, the difference is that
imx7d support HS400.

So introduce a new compatible string for imx7d and add HS400
support for imx7d usdhc.

Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/host/sdhci-esdhc-imx.c

index c6b9f6492e1a2529b7f683686bc4d939229dba63..b8b7e8842ed0cea5144cd84bb00dcb40ca6748eb 100644 (file)
@@ -44,6 +44,7 @@
 #define  ESDHC_MIX_CTRL_EXE_TUNE       (1 << 22)
 #define  ESDHC_MIX_CTRL_SMPCLK_SEL     (1 << 23)
 #define  ESDHC_MIX_CTRL_FBCLK_SEL      (1 << 25)
+#define  ESDHC_MIX_CTRL_HS400_EN       (1 << 26)
 /* Bits 3 and 6 are not SDHCI standard definitions */
 #define  ESDHC_MIX_CTRL_SDHCI_MASK     0xb7
 /* Tuning bits */
 #define  ESDHC_TUNE_CTRL_MIN           0
 #define  ESDHC_TUNE_CTRL_MAX           ((1 << 7) - 1)
 
+/* strobe dll register */
+#define ESDHC_STROBE_DLL_CTRL          0x70
+#define ESDHC_STROBE_DLL_CTRL_ENABLE   (1 << 0)
+#define ESDHC_STROBE_DLL_CTRL_RESET    (1 << 1)
+#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT     3
+
+#define ESDHC_STROBE_DLL_STATUS                0x74
+#define ESDHC_STROBE_DLL_STS_REF_LOCK  (1 << 1)
+#define ESDHC_STROBE_DLL_STS_SLV_LOCK  0x1
+
 #define ESDHC_TUNING_CTRL              0xcc
 #define ESDHC_STD_TUNING_EN            (1 << 24)
 /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
 #define ESDHC_FLAG_ERR004536           BIT(7)
 /* The IP supports HS200 mode */
 #define ESDHC_FLAG_HS200               BIT(8)
+/* The IP supports HS400 mode */
+#define ESDHC_FLAG_HS400               BIT(9)
+
+/* A higher clock ferquency than this rate requires strobell dll control */
+#define ESDHC_STROBE_DLL_CLK_FREQ      100000000
 
 struct esdhc_soc_data {
        u32 flags;
@@ -156,6 +172,12 @@ static struct esdhc_soc_data usdhc_imx6sx_data = {
                        | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200,
 };
 
+static struct esdhc_soc_data usdhc_imx7d_data = {
+       .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
+                       | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
+                       | ESDHC_FLAG_HS400,
+};
+
 struct pltfm_imx_data {
        u32 scratchpad;
        struct pinctrl *pinctrl;
@@ -199,6 +221,7 @@ static const struct of_device_id imx_esdhc_dt_ids[] = {
        { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
        { .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, },
        { .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, },
+       { .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, },
        { /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
@@ -274,6 +297,9 @@ static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
                                val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104
                                        | SDHCI_SUPPORT_SDR50
                                        | SDHCI_USE_SDR50_TUNING;
+
+                       if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
+                               val |= SDHCI_SUPPORT_HS400;
                }
        }
 
@@ -774,6 +800,7 @@ static int esdhc_change_pinstate(struct sdhci_host *host,
                break;
        case MMC_TIMING_UHS_SDR104:
        case MMC_TIMING_MMC_HS200:
+       case MMC_TIMING_MMC_HS400:
                pinctrl = imx_data->pins_200mhz;
                break;
        default:
@@ -784,24 +811,68 @@ static int esdhc_change_pinstate(struct sdhci_host *host,
        return pinctrl_select_state(imx_data->pinctrl, pinctrl);
 }
 
+/*
+ * For HS400 eMMC, there is a data_strobe line, this signal is generated
+ * by the device and used for data output and CRC status response output
+ * in HS400 mode. The frequency of this signal follows the frequency of
+ * CLK generated by host. Host receive the data which is aligned to the
+ * edge of data_strobe line. Due to the time delay between CLK line and
+ * data_strobe line, if the delay time is larger than one clock cycle,
+ * then CLK and data_strobe line will misaligned, read error shows up.
+ * So when the CLK is higher than 100MHz, each clock cycle is short enough,
+ * host should config the delay target.
+ */
+static void esdhc_set_strobe_dll(struct sdhci_host *host)
+{
+       u32 v;
+
+       if (host->mmc->actual_clock > ESDHC_STROBE_DLL_CLK_FREQ) {
+               /* force a reset on strobe dll */
+               writel(ESDHC_STROBE_DLL_CTRL_RESET,
+                       host->ioaddr + ESDHC_STROBE_DLL_CTRL);
+               /*
+                * enable strobe dll ctrl and adjust the delay target
+                * for the uSDHC loopback read clock
+                */
+               v = ESDHC_STROBE_DLL_CTRL_ENABLE |
+                       (7 << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
+               writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
+               /* wait 1us to make sure strobe dll status register stable */
+               udelay(1);
+               v = readl(host->ioaddr + ESDHC_STROBE_DLL_STATUS);
+               if (!(v & ESDHC_STROBE_DLL_STS_REF_LOCK))
+                       dev_warn(mmc_dev(host->mmc),
+                               "warning! HS400 strobe DLL status REF not lock!\n");
+               if (!(v & ESDHC_STROBE_DLL_STS_SLV_LOCK))
+                       dev_warn(mmc_dev(host->mmc),
+                               "warning! HS400 strobe DLL status SLV not lock!\n");
+       }
+}
+
 static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
 {
+       u32 m;
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct pltfm_imx_data *imx_data = pltfm_host->priv;
        struct esdhc_platform_data *boarddata = &imx_data->boarddata;
 
+       /* disable ddr mode and disable HS400 mode */
+       m = readl(host->ioaddr + ESDHC_MIX_CTRL);
+       m &= ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN);
+       imx_data->is_ddr = 0;
+
        switch (timing) {
        case MMC_TIMING_UHS_SDR12:
        case MMC_TIMING_UHS_SDR25:
        case MMC_TIMING_UHS_SDR50:
        case MMC_TIMING_UHS_SDR104:
        case MMC_TIMING_MMC_HS200:
+               writel(m, host->ioaddr + ESDHC_MIX_CTRL);
                break;
        case MMC_TIMING_UHS_DDR50:
        case MMC_TIMING_MMC_DDR52:
-               writel(readl(host->ioaddr + ESDHC_MIX_CTRL) |
-                               ESDHC_MIX_CTRL_DDREN,
-                               host->ioaddr + ESDHC_MIX_CTRL);
+               m |= ESDHC_MIX_CTRL_DDREN;
+               writel(m, host->ioaddr + ESDHC_MIX_CTRL);
                imx_data->is_ddr = 1;
                if (boarddata->delay_line) {
                        u32 v;
@@ -813,6 +884,12 @@ static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
                        writel(v, host->ioaddr + ESDHC_DLL_CTRL);
                }
                break;
+       case MMC_TIMING_MMC_HS400:
+               m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN;
+               writel(m, host->ioaddr + ESDHC_MIX_CTRL);
+               imx_data->is_ddr = 1;
+               esdhc_set_strobe_dll(host);
+               break;
        }
 
        esdhc_change_pinstate(host, timing);
@@ -1100,6 +1177,9 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
        if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536)
                host->quirks |= SDHCI_QUIRK_BROKEN_ADMA;
 
+       if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
+               host->quirks2 |= SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400;
+
        if (of_id)
                err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data);
        else