usb: phy: tegra: Tegra30 support
authorTuomas Tynkkynen <ttynkkynen@nvidia.com>
Mon, 12 Aug 2013 13:06:51 +0000 (16:06 +0300)
committerFelipe Balbi <balbi@ti.com>
Mon, 12 Aug 2013 18:29:48 +0000 (13:29 -0500)
The Tegra30 USB PHY is a bit different than the Tegra20 PHY:

- The EHCI controller supports the HOSTPC register extension, and some
  of the fields that the PHY needs to modify (PHCD and PTS) have moved
  to the new HOSTPC register.
- Some of the UTMI PLL configuration registers have moved from the USB
  register space to the Clock-And-Reset controller space. In Tegra30
  the clock driver is responsible for configuring the UTMI PLL.
- The USBMODE register must be explicitly written to enter host mode.
- Certain PHY parameters need to be programmed for optimal signal
  quality. Support for this will be added in the next patch.

The new tegra_phy_soc_config structure is added to describe the
differences between the SoCs.

Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/phy/phy-tegra-usb.c
include/linux/usb/tegra_usb_phy.h

index ebbf85fdfc7fc4ca8286d33c62c65c610bfaa42e..1ad184af7601102d69dd1fef277c795ab0b1c61a 100644 (file)
@@ -28,6 +28,7 @@
 #include <linux/io.h>
 #include <linux/gpio.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/of_gpio.h>
 #include <linux/usb/otg.h>
 #include <linux/usb/ulpi.h>
 
 #define ULPI_VIEWPORT          0x170
 
-/* PORTSC registers */
+/* PORTSC PTS/PHCD bits, Tegra20 only */
 #define TEGRA_USB_PORTSC1                              0x184
 #define TEGRA_USB_PORTSC1_PTS(x)                       (((x) & 0x3) << 30)
 #define TEGRA_USB_PORTSC1_PHCD                         (1 << 23)
 
+/* HOSTPC1 PTS/PHCD bits, Tegra30 and above */
+#define TEGRA_USB_HOSTPC1_DEVLC                0x1b4
+#define TEGRA_USB_HOSTPC1_DEVLC_PTS(x) (((x) & 0x7) << 29)
+#define TEGRA_USB_HOSTPC1_DEVLC_PHCD   (1 << 22)
+
 /* Bits of PORTSC1, which will get cleared by writing 1 into them */
 #define TEGRA_PORTSC1_RWC_BITS (PORT_CSC | PORT_PEC | PORT_OCC)
 
 #define UTMIP_BIAS_CFG1                0x83c
 #define   UTMIP_BIAS_PDTRK_COUNT(x)    (((x) & 0x1f) << 3)
 
+/* For Tegra30 and above only, the address is different in Tegra20 */
+#define USB_USBMODE            0x1f8
+#define   USB_USBMODE_MASK             (3 << 0)
+#define   USB_USBMODE_HOST             (3 << 0)
+#define   USB_USBMODE_DEVICE           (2 << 0)
+
 static DEFINE_SPINLOCK(utmip_pad_lock);
 static int utmip_pad_count;
 
@@ -193,10 +205,17 @@ static void set_pts(struct tegra_usb_phy *phy, u8 pts_val)
        void __iomem *base = phy->regs;
        unsigned long val;
 
-       val = readl(base + TEGRA_USB_PORTSC1) & ~TEGRA_PORTSC1_RWC_BITS;
-       val &= ~TEGRA_USB_PORTSC1_PTS(3);
-       val |= TEGRA_USB_PORTSC1_PTS(pts_val & 3);
-       writel(val, base + TEGRA_USB_PORTSC1);
+       if (phy->soc_config->has_hostpc) {
+               val = readl(base + TEGRA_USB_HOSTPC1_DEVLC);
+               val &= ~TEGRA_USB_HOSTPC1_DEVLC_PTS(~0);
+               val |= TEGRA_USB_HOSTPC1_DEVLC_PTS(pts_val);
+               writel(val, base + TEGRA_USB_HOSTPC1_DEVLC);
+       } else {
+               val = readl(base + TEGRA_USB_PORTSC1) & ~TEGRA_PORTSC1_RWC_BITS;
+               val &= ~TEGRA_USB_PORTSC1_PTS(~0);
+               val |= TEGRA_USB_PORTSC1_PTS(pts_val);
+               writel(val, base + TEGRA_USB_PORTSC1);
+       }
 }
 
 static void set_phcd(struct tegra_usb_phy *phy, bool enable)
@@ -204,12 +223,21 @@ static void set_phcd(struct tegra_usb_phy *phy, bool enable)
        void __iomem *base = phy->regs;
        unsigned long val;
 
-       val = readl(base + TEGRA_USB_PORTSC1) & ~TEGRA_PORTSC1_RWC_BITS;
-       if (enable)
-               val |= TEGRA_USB_PORTSC1_PHCD;
-       else
-               val &= ~TEGRA_USB_PORTSC1_PHCD;
-       writel(val, base + TEGRA_USB_PORTSC1);
+       if (phy->soc_config->has_hostpc) {
+               val = readl(base + TEGRA_USB_HOSTPC1_DEVLC);
+               if (enable)
+                       val |= TEGRA_USB_HOSTPC1_DEVLC_PHCD;
+               else
+                       val &= ~TEGRA_USB_HOSTPC1_DEVLC_PHCD;
+               writel(val, base + TEGRA_USB_HOSTPC1_DEVLC);
+       } else {
+               val = readl(base + TEGRA_USB_PORTSC1) & ~PORT_RWC_BITS;
+               if (enable)
+                       val |= TEGRA_USB_PORTSC1_PHCD;
+               else
+                       val &= ~TEGRA_USB_PORTSC1_PHCD;
+               writel(val, base + TEGRA_USB_PORTSC1);
+       }
 }
 
 static int utmip_pad_open(struct tegra_usb_phy *phy)
@@ -367,17 +395,21 @@ static int utmi_phy_power_on(struct tegra_usb_phy *phy)
        val &= ~UTMIP_SUSPEND_EXIT_ON_EDGE;
        writel(val, base + UTMIP_MISC_CFG0);
 
-       val = readl(base + UTMIP_MISC_CFG1);
-       val &= ~(UTMIP_PLL_ACTIVE_DLY_COUNT(~0) | UTMIP_PLLU_STABLE_COUNT(~0));
-       val |= UTMIP_PLL_ACTIVE_DLY_COUNT(phy->freq->active_delay) |
-               UTMIP_PLLU_STABLE_COUNT(phy->freq->stable_count);
-       writel(val, base + UTMIP_MISC_CFG1);
-
-       val = readl(base + UTMIP_PLL_CFG1);
-       val &= ~(UTMIP_XTAL_FREQ_COUNT(~0) | UTMIP_PLLU_ENABLE_DLY_COUNT(~0));
-       val |= UTMIP_XTAL_FREQ_COUNT(phy->freq->xtal_freq_count) |
-               UTMIP_PLLU_ENABLE_DLY_COUNT(phy->freq->enable_delay);
-       writel(val, base + UTMIP_PLL_CFG1);
+       if (!phy->soc_config->utmi_pll_config_in_car_module) {
+               val = readl(base + UTMIP_MISC_CFG1);
+               val &= ~(UTMIP_PLL_ACTIVE_DLY_COUNT(~0) |
+                       UTMIP_PLLU_STABLE_COUNT(~0));
+               val |= UTMIP_PLL_ACTIVE_DLY_COUNT(phy->freq->active_delay) |
+                       UTMIP_PLLU_STABLE_COUNT(phy->freq->stable_count);
+               writel(val, base + UTMIP_MISC_CFG1);
+
+               val = readl(base + UTMIP_PLL_CFG1);
+               val &= ~(UTMIP_XTAL_FREQ_COUNT(~0) |
+                       UTMIP_PLLU_ENABLE_DLY_COUNT(~0));
+               val |= UTMIP_XTAL_FREQ_COUNT(phy->freq->xtal_freq_count) |
+                       UTMIP_PLLU_ENABLE_DLY_COUNT(phy->freq->enable_delay);
+               writel(val, base + UTMIP_PLL_CFG1);
+       }
 
        if (phy->mode == USB_DR_MODE_PERIPHERAL) {
                val = readl(base + USB_SUSP_CTRL);
@@ -448,6 +480,16 @@ static int utmi_phy_power_on(struct tegra_usb_phy *phy)
 
        utmi_phy_clk_enable(phy);
 
+       if (phy->soc_config->requires_usbmode_setup) {
+               val = readl(base + USB_USBMODE);
+               val &= ~USB_USBMODE_MASK;
+               if (phy->mode == USB_DR_MODE_HOST)
+                       val |= USB_USBMODE_HOST;
+               else
+                       val |= USB_USBMODE_DEVICE;
+               writel(val, base + USB_USBMODE);
+       }
+
        if (!phy->is_legacy_phy)
                set_pts(phy, 0);
 
@@ -864,8 +906,30 @@ static int utmi_phy_probe(struct tegra_usb_phy *tegra_phy,
        return 0;
 }
 
+static const struct tegra_phy_soc_config tegra20_soc_config = {
+       .utmi_pll_config_in_car_module = false,
+       .has_hostpc = false,
+       .requires_usbmode_setup = false,
+       .requires_extra_tuning_parameters = false,
+};
+
+static const struct tegra_phy_soc_config tegra30_soc_config = {
+       .utmi_pll_config_in_car_module = true,
+       .has_hostpc = true,
+       .requires_usbmode_setup = true,
+       .requires_extra_tuning_parameters = true,
+};
+
+static struct of_device_id tegra_usb_phy_id_table[] = {
+       { .compatible = "nvidia,tegra30-usb-phy", .data = &tegra30_soc_config },
+       { .compatible = "nvidia,tegra20-usb-phy", .data = &tegra20_soc_config },
+       { },
+};
+MODULE_DEVICE_TABLE(of, tegra_usb_phy_id_table);
+
 static int tegra_usb_phy_probe(struct platform_device *pdev)
 {
+       const struct of_device_id *match;
        struct resource *res;
        struct tegra_usb_phy *tegra_phy = NULL;
        struct device_node *np = pdev->dev.of_node;
@@ -878,6 +942,13 @@ static int tegra_usb_phy_probe(struct platform_device *pdev)
                return -ENOMEM;
        }
 
+       match = of_match_device(tegra_usb_phy_id_table, &pdev->dev);
+       if (!match) {
+               dev_err(&pdev->dev, "Error: No device match found\n");
+               return -ENODEV;
+       }
+       tegra_phy->soc_config = match->data;
+
        res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
        if (!res) {
                dev_err(&pdev->dev, "Failed to get I/O memory\n");
@@ -968,12 +1039,6 @@ static int tegra_usb_phy_remove(struct platform_device *pdev)
        return 0;
 }
 
-static struct of_device_id tegra_usb_phy_id_table[] = {
-       { .compatible = "nvidia,tegra20-usb-phy", },
-       { },
-};
-MODULE_DEVICE_TABLE(of, tegra_usb_phy_id_table);
-
 static struct platform_driver tegra_usb_phy_driver = {
        .probe          = tegra_usb_phy_probe,
        .remove         = tegra_usb_phy_remove,
index d3db274610a1fe066081b1992984803acab29bbb..d3a63c354db970e2b56dc27e5b700a3c74af26b5 100644 (file)
 #include <linux/clk.h>
 #include <linux/usb/otg.h>
 
+/*
+ * utmi_pll_config_in_car_module: true if the UTMI PLL configuration registers
+ *     should be set up by clk-tegra, false if by the PHY code
+ * has_hostpc: true if the USB controller has the HOSTPC extension, which
+ *     changes the location of the PHCD and PTS fields
+ * requires_usbmode_setup: true if the USBMODE register needs to be set to
+ *      enter host mode
+ * requires_extra_tuning_parameters: true if xcvr_hsslew, hssquelch_level
+ *      and hsdiscon_level should be set for adequate signal quality
+ */
+
+struct tegra_phy_soc_config {
+       bool utmi_pll_config_in_car_module;
+       bool has_hostpc;
+       bool requires_usbmode_setup;
+       bool requires_extra_tuning_parameters;
+};
+
 struct tegra_utmip_config {
        u8 hssync_start_delay;
        u8 elastic_limit;
@@ -47,6 +65,7 @@ struct tegra_usb_phy {
        struct regulator *vbus;
        enum usb_dr_mode mode;
        void *config;
+       const struct tegra_phy_soc_config *soc_config;
        struct usb_phy *ulpi;
        struct usb_phy u_phy;
        bool is_legacy_phy;