USB: EHCI: add delay during suspend to prevent erroneous wakeups
authorAlan Stern <stern@rowland.harvard.edu>
Thu, 13 Feb 2014 20:49:17 +0000 (15:49 -0500)
committerGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Tue, 18 Feb 2014 20:04:41 +0000 (12:04 -0800)
High-speed USB connections revert back to full-speed signalling when
the device goes into suspend.  This takes several milliseconds, and
during that time it's not possible to tell reliably whether the device
has been disconnected.

On some platforms, the Wake-On-Disconnect circuitry gets confused
during this intermediate state.  It generates a false wakeup signal,
which can prevent the controller from going to sleep.

To avoid this problem, this patch adds a 5-ms delay to the
ehci_bus_suspend() routine if any ports have to switch over to
full-speed signalling.  (Actually, the delay was already present for
devices using a particular kind of PHY power management; the patch
merely causes the delay to be used more widely.)

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Peter Chen <Peter.Chen@freescale.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/host/ehci-hub.c

index 47b858fc50b2ee484c035cef8fe8b27c669009b5..7ae0c4d517417d46dbc2dd8f51993728fa839c3a 100644 (file)
@@ -238,6 +238,7 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
        int                     port;
        int                     mask;
        int                     changed;
+       bool                    fs_idle_delay;
 
        ehci_dbg(ehci, "suspend root hub\n");
 
@@ -272,6 +273,7 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
        ehci->bus_suspended = 0;
        ehci->owned_ports = 0;
        changed = 0;
+       fs_idle_delay = false;
        port = HCS_N_PORTS(ehci->hcs_params);
        while (port--) {
                u32 __iomem     *reg = &ehci->regs->port_status [port];
@@ -300,16 +302,32 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
                }
 
                if (t1 != t2) {
+                       /*
+                        * On some controllers, Wake-On-Disconnect will
+                        * generate false wakeup signals until the bus
+                        * switches over to full-speed idle.  For their
+                        * sake, add a delay if we need one.
+                        */
+                       if ((t2 & PORT_WKDISC_E) &&
+                                       ehci_port_speed(ehci, t2) ==
+                                               USB_PORT_STAT_HIGH_SPEED)
+                               fs_idle_delay = true;
                        ehci_writel(ehci, t2, reg);
                        changed = 1;
                }
        }
+       spin_unlock_irq(&ehci->lock);
+
+       if ((changed && ehci->has_tdi_phy_lpm) || fs_idle_delay) {
+               /*
+                * Wait for HCD to enter low-power mode or for the bus
+                * to switch to full-speed idle.
+                */
+               usleep_range(5000, 5500);
+       }
 
        if (changed && ehci->has_tdi_phy_lpm) {
-               spin_unlock_irq(&ehci->lock);
-               msleep(5);      /* 5 ms for HCD to enter low-power mode */
                spin_lock_irq(&ehci->lock);
-
                port = HCS_N_PORTS(ehci->hcs_params);
                while (port--) {
                        u32 __iomem     *hostpc_reg = &ehci->regs->hostpc[port];
@@ -322,8 +340,8 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
                                        port, (t3 & HOSTPC_PHCD) ?
                                        "succeeded" : "failed");
                }
+               spin_unlock_irq(&ehci->lock);
        }
-       spin_unlock_irq(&ehci->lock);
 
        /* Apparently some devices need a >= 1-uframe delay here */
        if (ehci->bus_suspended)