When this value is greater than 1, the driver will show the
stack trace additionally. This may help the debugging.
+ Since 2.6.30, this option also enables the hwptr check using
+ jiffies. This detects spontaneous invalid pointer callback
+ values, but can be lead to too much corrections for a (mostly
+ buggy) hardware that doesn't give smooth pointer updates.
+
card*/pcm*/sub*/info
The general information of this PCM sub-stream.
new_hw_ptr = hw_base + pos;
}
}
+
+ /* Do jiffies check only in xrun_debug mode */
+ if (!xrun_debug(substream))
+ goto no_jiffies_check;
+
/* Skip the jiffies check for hardwares with BATCH flag.
* Such hardware usually just increases the position at each IRQ,
* thus it can't give any strange position.
hw_base = 0;
new_hw_ptr = hw_base + pos;
}
- if (((delta * HZ) / runtime->rate) > jdelta + HZ/100) {
+ /* Do jiffies check only in xrun_debug mode */
+ if (xrun_debug(substream) &&
+ ((delta * HZ) / runtime->rate) > jdelta + HZ/100) {
hw_ptr_error(substream,
"hw_ptr skipping! "
"(pos=%ld, delta=%ld, period=%ld, jdelta=%lu/%lu)\n",
runtime->status->hw_ptr %= runtime->buffer_size;
else
runtime->status->hw_ptr = 0;
- runtime->hw_ptr_jiffies = jiffies;
snd_pcm_stream_unlock_irqrestore(substream, flags);
return 0;
}
{
struct snd_pcm_runtime *runtime = substream->runtime;
snd_pcm_trigger_tstamp(substream);
+ runtime->hw_ptr_jiffies = jiffies;
runtime->status->state = state;
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK &&
runtime->silence_size > 0)
{
if (substream->runtime->trigger_master != substream)
return 0;
+ /* The jiffies check in snd_pcm_update_hw_ptr*() is done by
+ * a delta betwen the current jiffies, this gives a large enough
+ * delta, effectively to skip the check once.
+ */
+ substream->runtime->hw_ptr_jiffies = jiffies - HZ * 1000;
return substream->ops->trigger(substream,
push ? SNDRV_PCM_TRIGGER_PAUSE_PUSH :
SNDRV_PCM_TRIGGER_PAUSE_RELEASE);
static struct snd_pci_quirk cxt5051_cfg_tbl[] = {
SND_PCI_QUIRK(0x103c, 0x30cf, "HP DV6736", CXT5051_HP_DV6736),
+ SND_PCI_QUIRK(0x103c, 0x360b, "Compaq Presario CQ60", CXT5051_HP),
SND_PCI_QUIRK(0x14f1, 0x0101, "Conexant Reference board",
CXT5051_LAPTOP),
SND_PCI_QUIRK(0x14f1, 0x5051, "HP Spartan 1.1", CXT5051_HP),
[QUIRK_MIDI_YAMAHA] = snd_usb_create_midi_interface,
[QUIRK_MIDI_MIDIMAN] = snd_usb_create_midi_interface,
[QUIRK_MIDI_NOVATION] = snd_usb_create_midi_interface,
- [QUIRK_MIDI_RAW] = snd_usb_create_midi_interface,
+ [QUIRK_MIDI_FASTLANE] = snd_usb_create_midi_interface,
[QUIRK_MIDI_EMAGIC] = snd_usb_create_midi_interface,
[QUIRK_MIDI_CME] = snd_usb_create_midi_interface,
[QUIRK_AUDIO_STANDARD_INTERFACE] = create_standard_audio_quirk,
QUIRK_MIDI_YAMAHA,
QUIRK_MIDI_MIDIMAN,
QUIRK_MIDI_NOVATION,
- QUIRK_MIDI_RAW,
+ QUIRK_MIDI_FASTLANE,
QUIRK_MIDI_EMAGIC,
QUIRK_MIDI_CME,
QUIRK_MIDI_US122L,
umidi->usb_protocol_ops = &snd_usbmidi_novation_ops;
err = snd_usbmidi_detect_per_port_endpoints(umidi, endpoints);
break;
- case QUIRK_MIDI_RAW:
+ case QUIRK_MIDI_FASTLANE:
umidi->usb_protocol_ops = &snd_usbmidi_raw_ops;
+ /*
+ * Interface 1 contains isochronous endpoints, but with the same
+ * numbers as in interface 0. Since it is interface 1 that the
+ * USB core has most recently seen, these descriptors are now
+ * associated with the endpoint numbers. This will foul up our
+ * attempts to submit bulk/interrupt URBs to the endpoints in
+ * interface 0, so we have to make sure that the USB core looks
+ * again at interface 0 by calling usb_set_interface() on it.
+ */
+ usb_set_interface(umidi->chip->dev, 0, 0);
err = snd_usbmidi_detect_per_port_endpoints(umidi, endpoints);
break;
case QUIRK_MIDI_EMAGIC:
.data = & (const struct snd_usb_audio_quirk[]) {
{
.ifnum = 0,
- .type = QUIRK_MIDI_RAW
+ .type = QUIRK_MIDI_FASTLANE
},
{
.ifnum = 1,