[PATCH] skge: make Genesis/Broadcom code work
authorStephen Hemminger <shemminger@osdl.org>
Mon, 27 Jun 2005 18:33:12 +0000 (11:33 -0700)
committerJeff Garzik <jgarzik@pobox.com>
Mon, 27 Jun 2005 22:05:06 +0000 (18:05 -0400)
Rewrite the code for handling the Broadcom PHY to something that
works. Remove link polling because Broadcom and Yukon don't need it.
When I wrote initial code, didn't have a genesis chipset based
board to test, so it was a non-working guess.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
drivers/net/skge.c
drivers/net/skge.h

index 81b8fe9581c7144c08fb6c41f2903e858cd048a8..f11e0e1a3d0e086531cf8bd4370be3f9c3e7e296 100644 (file)
@@ -54,7 +54,6 @@
 #define TX_WATCHDOG            (5 * HZ)
 #define NAPI_WEIGHT            64
 #define BLINK_HZ               (HZ/4)
-#define LINK_POLL_HZ           (HZ/10)
 
 MODULE_DESCRIPTION("SysKonnect Gigabit Ethernet driver");
 MODULE_AUTHOR("Stephen Hemminger <shemminger@osdl.org>");
@@ -96,6 +95,7 @@ static void yukon_init(struct skge_hw *hw, int port);
 static void yukon_reset(struct skge_hw *hw, int port);
 static void genesis_mac_init(struct skge_hw *hw, int port);
 static void genesis_reset(struct skge_hw *hw, int port);
+static void genesis_link_up(struct skge_port *skge);
 
 static const int txqaddr[] = { Q_XA1, Q_XA2 };
 static const int rxqaddr[] = { Q_R1, Q_R2 };
@@ -950,8 +950,7 @@ static void genesis_init(struct skge_hw *hw)
 
 static void genesis_reset(struct skge_hw *hw, int port)
 {
-       int i;
-       u64 zero = 0;
+       const u8 zero[8]  = { 0 };
 
        /* reset the statistics module */
        xm_write32(hw, port, XM_GP_PORT, XM_GP_RES_STAT);
@@ -963,20 +962,100 @@ static void genesis_reset(struct skge_hw *hw, int port)
        /* disable Broadcom PHY IRQ */
        xm_write16(hw, port, PHY_BCOM_INT_MASK, 0xffff);
 
-       xm_outhash(hw, port, XM_HSM, (u8 *) &zero);
-       for (i = 0; i < 15; i++)
-               xm_outaddr(hw, port, XM_EXM(i), (u8 *) &zero);
-       xm_outhash(hw, port, XM_SRC_CHK, (u8 *) &zero);
+       xm_outhash(hw, port, XM_HSM, zero);
 }
 
 
-static void genesis_mac_init(struct skge_hw *hw, int port)
+/* Convert mode to MII values  */
+static const u16 phy_pause_map[] = {
+       [FLOW_MODE_NONE] =      0,
+       [FLOW_MODE_LOC_SEND] =  PHY_AN_PAUSE_ASYM,
+       [FLOW_MODE_SYMMETRIC] = PHY_AN_PAUSE_CAP,
+       [FLOW_MODE_REM_SEND]  = PHY_AN_PAUSE_CAP | PHY_AN_PAUSE_ASYM,
+};
+
+
+/* Check status of Broadcom phy link */
+static void bcom_check_link(struct skge_hw *hw, int port)
 {
-       struct skge_port *skge = netdev_priv(hw->dev[port]);
+       struct net_device *dev = hw->dev[port];
+       struct skge_port *skge = netdev_priv(dev);
+       u16 status;
+
+       /* read twice because of latch */
+       (void) xm_phy_read(hw, port, PHY_BCOM_STAT);
+       status = xm_phy_read(hw, port, PHY_BCOM_STAT);
+
+       pr_debug("bcom_check_link status=0x%x\n", status);
+
+       if ((status & PHY_ST_LSYNC) == 0) {
+               u16 cmd = xm_read16(hw, port, XM_MMU_CMD);
+               cmd &= ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX);
+               xm_write16(hw, port, XM_MMU_CMD, cmd);
+               /* dummy read to ensure writing */
+               (void) xm_read16(hw, port, XM_MMU_CMD);
+
+               if (netif_carrier_ok(dev))
+                       skge_link_down(skge);
+       } else {
+               if (skge->autoneg == AUTONEG_ENABLE &&
+                   (status & PHY_ST_AN_OVER)) {
+                       u16 lpa = xm_phy_read(hw, port, PHY_BCOM_AUNE_LP);
+                       u16 aux = xm_phy_read(hw, port, PHY_BCOM_AUX_STAT);
+
+                       if (lpa & PHY_B_AN_RF) {
+                               printk(KERN_NOTICE PFX "%s: remote fault\n",
+                                      dev->name);
+                               return;
+                       }
+
+                       /* Check Duplex mismatch */
+                       switch(aux & PHY_B_AS_AN_RES_MSK) {
+                       case PHY_B_RES_1000FD:
+                               skge->duplex = DUPLEX_FULL;
+                               break;
+                       case PHY_B_RES_1000HD:
+                               skge->duplex = DUPLEX_HALF;
+                               break;
+                       default:
+                               printk(KERN_NOTICE PFX "%s: duplex mismatch\n",
+                                      dev->name);
+                               return;
+                       }
+
+
+                       /* We are using IEEE 802.3z/D5.0 Table 37-4 */
+                       switch (aux & PHY_B_AS_PAUSE_MSK) {
+                       case PHY_B_AS_PAUSE_MSK:
+                               skge->flow_control = FLOW_MODE_SYMMETRIC;
+                               break;
+                       case PHY_B_AS_PRR:
+                               skge->flow_control = FLOW_MODE_REM_SEND;
+                               break;
+                       case PHY_B_AS_PRT:
+                               skge->flow_control = FLOW_MODE_LOC_SEND;
+                               break;
+                       default:
+                               skge->flow_control = FLOW_MODE_NONE;
+                       }
+
+                       skge->speed = SPEED_1000;
+               }
+
+               if (!netif_carrier_ok(dev))
+                       genesis_link_up(skge);
+       }
+}
+
+/* Broadcom 5400 only supports giagabit! SysKonnect did not put an additional
+ * Phy on for 100 or 10Mbit operation
+ */
+static void bcom_phy_init(struct skge_port *skge, int jumbo)
+{
+       struct skge_hw *hw = skge->hw;
+       int port = skge->port;
        int i;
-       u32 r;
-       u16 id1;
-       u16 ctrl1, ctrl2, ctrl3, ctrl4, ctrl5;
+       u16 id1, r, ext, ctl;
 
        /* magic workaround patterns for Broadcom */
        static const struct {
@@ -992,6 +1071,110 @@ static void genesis_mac_init(struct skge_hw *hw, int port)
                { 0x17, 0x0013 }, { 0x15, 0x0A04 }, { 0x18, 0x0420 },
        };
 
+       pr_debug("bcom_phy_init\n");
+
+       /* read Id from external PHY (all have the same address) */
+       id1 = xm_phy_read(hw, port, PHY_XMAC_ID1);
+
+       /* Optimize MDIO transfer by suppressing preamble. */
+       r = xm_read16(hw, port, XM_MMU_CMD);
+       r |=  XM_MMU_NO_PRE;
+       xm_write16(hw, port, XM_MMU_CMD,r);
+
+       switch(id1) {
+       case PHY_BCOM_ID1_C0:
+               /*
+                * Workaround BCOM Errata for the C0 type.
+                * Write magic patterns to reserved registers.
+                */
+               for (i = 0; i < ARRAY_SIZE(C0hack); i++)
+                       xm_phy_write(hw, port,
+                                    C0hack[i].reg, C0hack[i].val);
+
+               break;
+       case PHY_BCOM_ID1_A1:
+               /*
+                * Workaround BCOM Errata for the A1 type.
+                * Write magic patterns to reserved registers.
+                */
+               for (i = 0; i < ARRAY_SIZE(A1hack); i++)
+                       xm_phy_write(hw, port,
+                                    A1hack[i].reg, A1hack[i].val);
+               break;
+       }
+
+       /*
+        * Workaround BCOM Errata (#10523) for all BCom PHYs.
+        * Disable Power Management after reset.
+        */
+       r = xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL);
+       r |= PHY_B_AC_DIS_PM;
+       xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL, r);
+
+       /* Dummy read */
+       xm_read16(hw, port, XM_ISRC);
+
+       ext = PHY_B_PEC_EN_LTR; /* enable tx led */
+       ctl = PHY_CT_SP1000;    /* always 1000mbit */
+
+       if (skge->autoneg == AUTONEG_ENABLE) {
+               /*
+                * Workaround BCOM Errata #1 for the C5 type.
+                * 1000Base-T Link Acquisition Failure in Slave Mode
+                * Set Repeater/DTE bit 10 of the 1000Base-T Control Register
+                */
+               u16 adv = PHY_B_1000C_RD;
+               if (skge->advertising & ADVERTISED_1000baseT_Half)
+                       adv |= PHY_B_1000C_AHD;
+               if (skge->advertising & ADVERTISED_1000baseT_Full)
+                       adv |= PHY_B_1000C_AFD;
+               xm_phy_write(hw, port, PHY_BCOM_1000T_CTRL, adv);
+
+               ctl |= PHY_CT_ANE | PHY_CT_RE_CFG;
+       } else {
+               if (skge->duplex == DUPLEX_FULL)
+                       ctl |= PHY_CT_DUP_MD;
+               /* Force to slave */
+               xm_phy_write(hw, port, PHY_BCOM_1000T_CTRL, PHY_B_1000C_MSE);
+       }
+
+       /* Set autonegotiation pause parameters */
+       xm_phy_write(hw, port, PHY_BCOM_AUNE_ADV,
+                    phy_pause_map[skge->flow_control] | PHY_AN_CSMA);
+
+       /* Handle Jumbo frames */
+       if (jumbo) {
+               xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL,
+                            PHY_B_AC_TX_TST | PHY_B_AC_LONG_PACK);
+
+               ext |= PHY_B_PEC_HIGH_LA;
+
+       }
+
+       xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, ext);
+       xm_phy_write(hw, port, PHY_BCOM_CTRL, ctl);
+
+       /* Use link status change interrrupt */
+       xm_phy_write(hw, port, PHY_BCOM_INT_MASK, PHY_B_DEF_MSK);
+
+       bcom_check_link(hw, port);
+}
+
+static void genesis_mac_init(struct skge_hw *hw, int port)
+{
+       struct net_device *dev = hw->dev[port];
+       struct skge_port *skge = netdev_priv(dev);
+       int jumbo = hw->dev[port]->mtu > ETH_DATA_LEN;
+       int i;
+       u32 r;
+       const u8 zero[6]  = { 0 };
+
+       /* Clear MIB counters */
+       xm_write16(hw, port, XM_STAT_CMD,
+                       XM_SC_CLR_RXC | XM_SC_CLR_TXC);
+       /* Clear two times according to Errata #3 */
+       xm_write16(hw, port, XM_STAT_CMD,
+                       XM_SC_CLR_RXC | XM_SC_CLR_TXC);
 
        /* initialize Rx, Tx and Link LED */
        skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_ON);
@@ -1009,9 +1192,7 @@ static void genesis_mac_init(struct skge_hw *hw, int port)
         * GMII mode.
         */
        spin_lock_bh(&hw->phy_lock);
-
-       /* External Phy Handling */
-       /* Take PHY out of reset. */
+       /* Take external Phy out of reset */
        r = skge_read32(hw, B2_GP_IO);
        if (port == 0)
                r |= GP_DIR_0|GP_IO_0;
@@ -1020,57 +1201,47 @@ static void genesis_mac_init(struct skge_hw *hw, int port)
 
        skge_write32(hw, B2_GP_IO, r);
        skge_read32(hw, B2_GP_IO);
+       spin_unlock_bh(&hw->phy_lock);
 
-       /* Enable GMII mode on the XMAC. */
+       /* Enable GMII interfac */
        xm_write16(hw, port, XM_HW_CFG, XM_HW_GMII_MD);
 
-       id1 = xm_phy_read(hw, port, PHY_XMAC_ID1);
+       bcom_phy_init(skge, jumbo);
 
-       /* Optimize MDIO transfer by suppressing preamble. */
-       xm_write16(hw, port, XM_MMU_CMD,
-                  xm_read16(hw, port, XM_MMU_CMD)
-                  | XM_MMU_NO_PRE);
+       /* Set Station Address */
+       xm_outaddr(hw, port, XM_SA, dev->dev_addr);
 
-       if (id1 == PHY_BCOM_ID1_C0) {
-               /*
-                * Workaround BCOM Errata for the C0 type.
-                * Write magic patterns to reserved registers.
-                */
-               for (i = 0; i < ARRAY_SIZE(C0hack); i++)
-                       xm_phy_write(hw, port,
-                                    C0hack[i].reg, C0hack[i].val);
+       /* We don't use match addresses so clear */
+       for (i = 1; i < 16; i++)
+               xm_outaddr(hw, port, XM_EXM(i), zero);
+
+       /* configure Rx High Water Mark (XM_RX_HI_WM) */
+       xm_write16(hw, port, XM_RX_HI_WM, 1450);
+
+       /* We don't need the FCS appended to the packet. */
+       r = XM_RX_LENERR_OK | XM_RX_STRIP_FCS;
+       if (jumbo)
+               r |= XM_RX_BIG_PK_OK;
 
-       } else if (id1 == PHY_BCOM_ID1_A1) {
+       if (skge->duplex == DUPLEX_HALF) {
                /*
-                * Workaround BCOM Errata for the A1 type.
-                * Write magic patterns to reserved registers.
+                * If in manual half duplex mode the other side might be in
+                * full duplex mode, so ignore if a carrier extension is not seen
+                * on frames received
                 */
-               for (i = 0; i < ARRAY_SIZE(A1hack); i++)
-                       xm_phy_write(hw, port,
-                                    A1hack[i].reg, A1hack[i].val);
+               r |= XM_RX_DIS_CEXT;
        }
+       xm_write16(hw, port, XM_RX_CMD, r);
 
-       /*
-        * Workaround BCOM Errata (#10523) for all BCom PHYs.
-        * Disable Power Management after reset.
-        */
-       r = xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL);
-       xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL, r | PHY_B_AC_DIS_PM);
-
-
-       /* Dummy read */
-       xm_read16(hw, port, XM_ISRC);
-
-       r = xm_read32(hw, port, XM_MODE);
-       xm_write32(hw, port, XM_MODE, r|XM_MD_CSA);
-
-       /* We don't need the FCS appended to the packet. */
-       r = xm_read16(hw, port, XM_RX_CMD);
-       xm_write16(hw, port, XM_RX_CMD, r | XM_RX_STRIP_FCS);
 
        /* We want short frames padded to 60 bytes. */
-       r = xm_read16(hw, port, XM_TX_CMD);
-       xm_write16(hw, port, XM_TX_CMD, r | XM_TX_AUTO_PAD);
+       xm_write16(hw, port, XM_TX_CMD, XM_TX_AUTO_PAD);
+
+       /*
+        * Bump up the transmit threshold. This helps hold off transmit
+        * underruns when we're blasting traffic from both ports at once.
+        */
+       xm_write16(hw, port, XM_TX_THR, 512);
 
        /*
         * Enable the reception of all error frames. This is is
@@ -1086,19 +1257,22 @@ static void genesis_mac_init(struct skge_hw *hw, int port)
         * case the XMAC will start transfering frames out of the
         * RX FIFO as soon as the FIFO threshold is reached.
         */
-       r = xm_read32(hw, port, XM_MODE);
-       xm_write32(hw, port, XM_MODE,
-                  XM_MD_RX_CRCE|XM_MD_RX_LONG|XM_MD_RX_RUNT|
-                  XM_MD_RX_ERR|XM_MD_RX_IRLE);
+       xm_write32(hw, port, XM_MODE, XM_DEF_MODE);
 
-       xm_outaddr(hw, port, XM_SA, hw->dev[port]->dev_addr);
-       xm_outaddr(hw, port, XM_EXM(0), hw->dev[port]->dev_addr);
 
        /*
-        * Bump up the transmit threshold. This helps hold off transmit
-        * underruns when we're blasting traffic from both ports at once.
+        * Initialize the Receive Counter Event Mask (XM_RX_EV_MSK)
+        *      - Enable all bits excepting 'Octets Rx OK Low CntOv'
+        *        and 'Octets Rx OK Hi Cnt Ov'.
         */
-       xm_write16(hw, port, XM_TX_THR, 512);
+       xm_write32(hw, port, XM_RX_EV_MSK, XMR_DEF_MSK);
+
+       /*
+        * Initialize the Transmit Counter Event Mask (XM_TX_EV_MSK)
+        *      - Enable all bits excepting 'Octets Tx OK Low CntOv'
+        *        and 'Octets Tx OK Hi Cnt Ov'.
+        */
+       xm_write32(hw, port, XM_TX_EV_MSK, XMT_DEF_MSK);
 
        /* Configure MAC arbiter */
        skge_write16(hw, B3_MA_TO_CTRL, MA_RST_CLR);
@@ -1124,89 +1298,14 @@ static void genesis_mac_init(struct skge_hw *hw, int port)
        skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_TX_CTRL_DEF);
        skge_write8(hw, SK_REG(port, TX_MFF_CTRL2), MFF_ENA_OP_MD);
 
-       if (hw->dev[port]->mtu > ETH_DATA_LEN) {
+       if (jumbo) {
                /* Enable frame flushing if jumbo frames used */
                skge_write16(hw, SK_REG(port,RX_MFF_CTRL1), MFF_ENA_FLUSH);
        } else {
                /* enable timeout timers if normal frames */
                skge_write16(hw, B3_PA_CTRL,
-                            port == 0 ? PA_ENA_TO_TX1 : PA_ENA_TO_TX2);
+                            (port == 0) ? PA_ENA_TO_TX1 : PA_ENA_TO_TX2);
        }
-
-
-       r = xm_read16(hw, port, XM_RX_CMD);
-       if (hw->dev[port]->mtu > ETH_DATA_LEN)
-               xm_write16(hw, port, XM_RX_CMD, r | XM_RX_BIG_PK_OK);
-       else
-               xm_write16(hw, port, XM_RX_CMD, r & ~(XM_RX_BIG_PK_OK));
-
-       /* Broadcom phy initialization */
-       ctrl1 = PHY_CT_SP1000;
-       ctrl2 = 0;
-       ctrl3 = PHY_AN_CSMA;
-       ctrl4 = PHY_B_PEC_EN_LTR;
-       ctrl5 = PHY_B_AC_TX_TST;
-
-       if (skge->autoneg == AUTONEG_ENABLE) {
-               /*
-                * Workaround BCOM Errata #1 for the C5 type.
-                * 1000Base-T Link Acquisition Failure in Slave Mode
-                * Set Repeater/DTE bit 10 of the 1000Base-T Control Register
-                */
-               ctrl2 |= PHY_B_1000C_RD;
-               if (skge->advertising & ADVERTISED_1000baseT_Half)
-                       ctrl2 |= PHY_B_1000C_AHD;
-               if (skge->advertising & ADVERTISED_1000baseT_Full)
-                       ctrl2 |= PHY_B_1000C_AFD;
-
-               /* Set Flow-control capabilities */
-               switch (skge->flow_control) {
-               case FLOW_MODE_NONE:
-                       ctrl3 |= PHY_B_P_NO_PAUSE;
-                       break;
-               case FLOW_MODE_LOC_SEND:
-                       ctrl3 |= PHY_B_P_ASYM_MD;
-                       break;
-               case FLOW_MODE_SYMMETRIC:
-                       ctrl3 |= PHY_B_P_SYM_MD;
-                       break;
-               case FLOW_MODE_REM_SEND:
-                       ctrl3 |= PHY_B_P_BOTH_MD;
-                       break;
-               }
-
-               /* Restart Auto-negotiation */
-               ctrl1 |= PHY_CT_ANE | PHY_CT_RE_CFG;
-       } else {
-               if (skge->duplex == DUPLEX_FULL)
-                       ctrl1 |= PHY_CT_DUP_MD;
-
-               ctrl2 |= PHY_B_1000C_MSE;       /* set it to Slave */
-       }
-
-       xm_phy_write(hw, port, PHY_BCOM_1000T_CTRL, ctrl2);
-       xm_phy_write(hw, port, PHY_BCOM_AUNE_ADV, ctrl3);
-
-       if (skge->netdev->mtu > ETH_DATA_LEN) {
-               ctrl4 |= PHY_B_PEC_HIGH_LA;
-               ctrl5 |= PHY_B_AC_LONG_PACK;
-
-               xm_phy_write(hw, port,PHY_BCOM_AUX_CTRL, ctrl5);
-       }
-
-       xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, ctrl4);
-       xm_phy_write(hw, port, PHY_BCOM_CTRL, ctrl1);
-       spin_unlock_bh(&hw->phy_lock);
-
-       /* Clear MIB counters */
-       xm_write16(hw, port, XM_STAT_CMD,
-                  XM_SC_CLR_RXC | XM_SC_CLR_TXC);
-       /* Clear two times according to Errata #3 */
-       xm_write16(hw, port, XM_STAT_CMD,
-                  XM_SC_CLR_RXC | XM_SC_CLR_TXC);
-
-       /* Start polling for link status */
-       mod_timer(&skge->link_check, jiffies + LINK_POLL_HZ);
 }
 
 static void genesis_stop(struct skge_port *skge)
@@ -1331,23 +1430,6 @@ static u16 gm_phy_read(struct skge_hw *hw, int port, u16 reg)
        return gma_read16(hw, port, GM_SMI_DATA);
 }
 
-static void genesis_link_down(struct skge_port *skge)
-{
-       struct skge_hw *hw = skge->hw;
-       int port = skge->port;
-
-       pr_debug("genesis_link_down\n");
-
-       xm_write16(hw, port, XM_MMU_CMD,
-                       xm_read16(hw, port, XM_MMU_CMD)
-                       & ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX));
-
-       /* dummy read to ensure writing */
-       (void) xm_read16(hw, port, XM_MMU_CMD);
-
-       skge_link_down(skge);
-}
-
 static void genesis_link_up(struct skge_port *skge)
 {
        struct skge_hw *hw = skge->hw;
@@ -1430,18 +1512,23 @@ static void genesis_link_up(struct skge_port *skge)
 }
 
 
-static void genesis_bcom_intr(struct skge_port *skge)
+static inline void bcom_phy_intr(struct skge_port *skge)
 {
        struct skge_hw *hw = skge->hw;
        int port = skge->port;
-       u16 stat = xm_phy_read(hw, port, PHY_BCOM_INT_STAT);
+       u16 isrc;
+
+       isrc = xm_phy_read(hw, port, PHY_BCOM_INT_STAT);
+       pr_debug("bcom_phy_interrupt status=0x%x\n", isrc);
 
-       pr_debug("genesis_bcom intr stat=%x\n", stat);
+       if (isrc & PHY_B_IS_PSE)
+               printk(KERN_ERR PFX "%s: uncorrectable pair swap error\n",
+                      hw->dev[port]->name);
 
        /* Workaround BCom Errata:
         *      enable and disable loopback mode if "NO HCD" occurs.
         */
-       if (stat & PHY_B_IS_NO_HDCL) {
+       if (isrc & PHY_B_IS_NO_HDCL) {
                u16 ctrl = xm_phy_read(hw, port, PHY_BCOM_CTRL);
                xm_phy_write(hw, port, PHY_BCOM_CTRL,
                                  ctrl | PHY_CT_LOOP);
@@ -1449,57 +1536,9 @@ static void genesis_bcom_intr(struct skge_port *skge)
                                  ctrl & ~PHY_CT_LOOP);
        }
 
-       stat = xm_phy_read(hw, port, PHY_BCOM_STAT);
-       if (stat & (PHY_B_IS_AN_PR | PHY_B_IS_LST_CHANGE)) {
-               u16 aux = xm_phy_read(hw, port, PHY_BCOM_AUX_STAT);
-               if ( !(aux & PHY_B_AS_LS) && netif_carrier_ok(skge->netdev))
-                       genesis_link_down(skge);
-
-               else if (stat & PHY_B_IS_LST_CHANGE) {
-                       if (aux & PHY_B_AS_AN_C) {
-                               switch (aux & PHY_B_AS_AN_RES_MSK) {
-                               case PHY_B_RES_1000FD:
-                                       skge->duplex = DUPLEX_FULL;
-                                       break;
-                               case PHY_B_RES_1000HD:
-                                       skge->duplex = DUPLEX_HALF;
-                                       break;
-                               }
-
-                               switch (aux & PHY_B_AS_PAUSE_MSK) {
-                               case PHY_B_AS_PAUSE_MSK:
-                                       skge->flow_control = FLOW_MODE_SYMMETRIC;
-                                       break;
-                               case PHY_B_AS_PRR:
-                                       skge->flow_control = FLOW_MODE_REM_SEND;
-                                       break;
-                               case PHY_B_AS_PRT:
-                                       skge->flow_control = FLOW_MODE_LOC_SEND;
-                                       break;
-                               default:
-                                       skge->flow_control = FLOW_MODE_NONE;
-                               }
-                               skge->speed = SPEED_1000;
-                       }
-                       genesis_link_up(skge);
-               }
-               else
-                       mod_timer(&skge->link_check, jiffies + LINK_POLL_HZ);
-       }
-}
-
-/* Perodic poll of phy status to check for link transistion  */
-static void skge_link_timer(unsigned long __arg)
-{
-       struct skge_port *skge = (struct skge_port *) __arg;
-       struct skge_hw *hw = skge->hw;
-
-       if (hw->chip_id != CHIP_ID_GENESIS || !netif_running(skge->netdev))
-               return;
+       if (isrc & (PHY_B_IS_AN_PR | PHY_B_IS_LST_CHANGE))
+               bcom_check_link(hw, port);
 
-       spin_lock_bh(&hw->phy_lock);
-       genesis_bcom_intr(skge);
-       spin_unlock_bh(&hw->phy_lock);
 }
 
 /* Marvell Phy Initailization */
@@ -1547,41 +1586,12 @@ static void yukon_init(struct skge_hw *hw, int port)
                                adv |= PHY_M_AN_10_FD;
                        if (skge->advertising & ADVERTISED_10baseT_Half)
                                adv |= PHY_M_AN_10_HD;
-
-                       /* Set Flow-control capabilities */
-                       switch (skge->flow_control) {
-                       case FLOW_MODE_NONE:
-                               adv |= PHY_B_P_NO_PAUSE;
-                               break;
-                       case FLOW_MODE_LOC_SEND:
-                               adv |= PHY_B_P_ASYM_MD;
-                               break;
-                       case FLOW_MODE_SYMMETRIC:
-                               adv |= PHY_B_P_SYM_MD;
-                               break;
-                       case FLOW_MODE_REM_SEND:
-                               adv |= PHY_B_P_BOTH_MD;
-                               break;
-                       }
-               } else {        /* special defines for FIBER (88E1011S only) */
+               } else  /* special defines for FIBER (88E1011S only) */
                        adv |= PHY_M_AN_1000X_AHD | PHY_M_AN_1000X_AFD;
 
-                       /* Set Flow-control capabilities */
-                       switch (skge->flow_control) {
-                       case FLOW_MODE_NONE:
-                               adv |= PHY_M_P_NO_PAUSE_X;
-                               break;
-                       case FLOW_MODE_LOC_SEND:
-                               adv |= PHY_M_P_ASYM_MD_X;
-                               break;
-                       case FLOW_MODE_SYMMETRIC:
-                               adv |= PHY_M_P_SYM_MD_X;
-                               break;
-                       case FLOW_MODE_REM_SEND:
-                               adv |= PHY_M_P_BOTH_MD_X;
-                               break;
-                       }
-               }
+               /* Set Flow-control capabilities */
+               adv |= phy_pause_map[skge->flow_control];
+
                /* Restart Auto-negotiation */
                ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG;
        } else {
@@ -2090,7 +2100,6 @@ static int skge_down(struct net_device *dev)
        netif_stop_queue(dev);
 
        del_timer_sync(&skge->led_blink);
-       del_timer_sync(&skge->link_check);
 
        /* Stop transmitter */
        skge_write8(hw, Q_ADDR(txqaddr[port], Q_CSR), CSR_STOP);
@@ -2325,6 +2334,8 @@ static void genesis_set_multicast(struct net_device *dev)
        u32 mode;
        u8 filter[8];
 
+       pr_debug("genesis_set_multicast flags=%x count=%d\n", dev->flags, dev->mc_count);
+
        mode = xm_read32(hw, port, XM_MODE);
        mode |= XM_MD_ENA_HASH;
        if (dev->flags & IFF_PROMISC)
@@ -2337,16 +2348,15 @@ static void genesis_set_multicast(struct net_device *dev)
        else {
                memset(filter, 0, sizeof(filter));
                for (i = 0; list && i < count; i++, list = list->next) {
-                       u32 crc = crc32_le(~0, list->dmi_addr, ETH_ALEN);
-                       u8 bit = 63 - (crc & 63);
-
+                       u32 crc, bit;
+                       crc = ether_crc_le(ETH_ALEN, list->dmi_addr);
+                       bit = ~crc & 0x3f;
                        filter[bit/8] |= 1 << (bit%8);
                }
        }
 
-       xm_outhash(hw, port, XM_HSM, filter);
-
        xm_write32(hw, port, XM_MODE, mode);
+       xm_outhash(hw, port, XM_HSM, filter);
 }
 
 static void yukon_set_multicast(struct net_device *dev)
@@ -2667,7 +2677,7 @@ static void skge_extirq(unsigned long data)
                        if (hw->chip_id != CHIP_ID_GENESIS)
                                yukon_phy_intr(skge);
                        else
-                               genesis_bcom_intr(skge);
+                               bcom_phy_intr(skge);
                }
        }
        spin_unlock(&hw->phy_lock);
@@ -2986,10 +2996,6 @@ static struct net_device *skge_devinit(struct skge_hw *hw, int port,
 
        spin_lock_init(&skge->tx_lock);
 
-       init_timer(&skge->link_check);
-       skge->link_check.function = skge_link_timer;
-       skge->link_check.data = (unsigned long) skge;
-
        init_timer(&skge->led_blink);
        skge->led_blink.function = skge_blink_timer;
        skge->led_blink.data = (unsigned long) skge;
index 6f3a4b56a671f5d1570bfeb3f447c6c513e436c9..6b9a2ebbab28681a72e785ec113d078a2ea46534 100644 (file)
@@ -1225,6 +1225,16 @@ enum {
        PHY_B_PES_MLT3_ER       = 1<<0, /* Bit  0:      MLT3 code Error */
 };
 
+/*  PHY_BCOM_AUNE_ADV  16 bit r/w      Auto-Negotiation Advertisement *****/
+/*  PHY_BCOM_AUNE_LP   16 bit r/o      Link Partner Ability Reg *****/
+enum {
+       PHY_B_AN_RF     = 1<<13, /* Bit 13:     Remote Fault */
+
+       PHY_B_AN_ASP    = 1<<11, /* Bit 11:     Asymmetric Pause */
+       PHY_B_AN_PC     = 1<<10, /* Bit 10:     Pause Capable */
+};
+
+
 /*****  PHY_BCOM_FC_CTR                16 bit r/w      False Carrier Counter *****/
 enum {
        PHY_B_FC_CTR    = 0xff, /* Bit  7..0:   False Carrier Counter */
@@ -1285,7 +1295,9 @@ enum {
        PHY_B_IS_LST_CHANGE     = 1<<1, /* Bit  1:      Link Status Changed */
        PHY_B_IS_CRC_ER = 1<<0, /* Bit  0:      CRC Error */
 };
-#define PHY_B_DEF_MSK  (~(PHY_B_IS_AN_PR | PHY_B_IS_LST_CHANGE))
+#define PHY_B_DEF_MSK  \
+       (~(PHY_B_IS_PSE | PHY_B_IS_AN_PR | PHY_B_IS_DUP_CHANGE | \
+           PHY_B_IS_LSP_CHANGE | PHY_B_IS_LST_CHANGE))
 
 /* Pause Bits (PHY_B_AN_ASP and PHY_B_AN_PC) encoding */
 enum {
@@ -2489,7 +2501,6 @@ struct skge_port {
        dma_addr_t           dma;
        unsigned long        mem_size;
 
-       struct timer_list    link_check;
        struct timer_list    led_blink;
 };