ARM: sun7i: cubietruck: Convert to DT label based syntax

In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
index 8f74a649576da72da1d563cac0832a512951c9a4..0c219a419f49082679744b41862c764356d9890d 100644 (file)
--- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
+++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
@@ -59,144 +59,6 @@
        model = "Cubietech Cubietruck";
        compatible = "cubietech,cubietruck", "allwinner,sun7i-a20";
 
-       soc@01c00000 {
-               mmc0: mmc@01c0f000 {
-                       pinctrl-names = "default";
-                       pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
-                       vmmc-supply = <&reg_vcc3v3>;
-                       bus-width = <4>;
-                       cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
-                       cd-inverted;
-                       status = "okay";
-               };
-
-               mmc3: mmc@01c12000 {
-                       pinctrl-names = "default";
-                       pinctrl-0 = <&mmc3_pins_a>;
-                       vmmc-supply = <&reg_vmmc3>;
-                       bus-width = <4>;
-                       non-removable;
-                       status = "okay";
-               };
-
-               usbphy: phy@01c13400 {
-                       usb0_vbus-supply = <&reg_usb0_vbus>;
-                       usb1_vbus-supply = <&reg_usb1_vbus>;
-                       usb2_vbus-supply = <&reg_usb2_vbus>;
-                       status = "okay";
-               };
-
-               ehci0: usb@01c14000 {
-                       status = "okay";
-               };
-
-               ohci0: usb@01c14400 {
-                       status = "okay";
-               };
-
-               ahci: sata@01c18000 {
-                       target-supply = <&reg_ahci_5v>;
-                       status = "okay";
-               };
-
-               ehci1: usb@01c1c000 {
-                       status = "okay";
-               };
-
-               ohci1: usb@01c1c400 {
-                       status = "okay";
-               };
-
-               pinctrl@01c20800 {
-                       mmc3_pins_a: mmc3@0 {
-                               /* AP6210 requires pull-up */
-                               allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-                       };
-
-                       vmmc3_pin_cubietruck: vmmc3_pin@0 {
-                               allwinner,pins = "PH9";
-                               allwinner,function = "gpio_out";
-                               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-                               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-                       };
-
-                       ahci_pwr_pin_cubietruck: ahci_pwr_pin@1 {
-                               allwinner,pins = "PH12";
-                               allwinner,function = "gpio_out";
-                               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-                               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-                       };
-
-                       led_pins_cubietruck: led_pins@0 {
-                               allwinner,pins = "PH7", "PH11", "PH20", "PH21";
-                               allwinner,function = "gpio_out";
-                               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-                               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-                       };
-
-                       usb0_vbus_pin_a: usb0_vbus_pin@0 {
-                               allwinner,pins = "PH17";
-                               allwinner,function = "gpio_out";
-                               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-                               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-                       };
-               };
-
-               pwm: pwm@01c20e00 {
-                       pinctrl-names = "default";
-                       pinctrl-0 = <&pwm0_pins_a>, <&pwm1_pins_a>;
-                       status = "okay";
-               };
-
-               ir0: ir@01c21800 {
-                       pinctrl-names = "default";
-                       pinctrl-0 = <&ir0_pins_a>;
-                       status = "okay";
-               };
-
-               uart0: serial@01c28000 {
-                       pinctrl-names = "default";
-                       pinctrl-0 = <&uart0_pins_a>;
-                       status = "okay";
-               };
-
-               i2c0: i2c@01c2ac00 {
-                       pinctrl-names = "default";
-                       pinctrl-0 = <&i2c0_pins_a>;
-                       status = "okay";
-
-                       axp209: pmic@34 {
-                               reg = <0x34>;
-                               interrupt-parent = <&nmi_intc>;
-                               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-                       };
-               };
-
-               i2c1: i2c@01c2b000 {
-                       pinctrl-names = "default";
-                       pinctrl-0 = <&i2c1_pins_a>;
-                       status = "okay";
-               };
-
-               i2c2: i2c@01c2b400 {
-                       pinctrl-names = "default";
-                       pinctrl-0 = <&i2c2_pins_a>;
-                       status = "okay";
-               };
-
-               gmac: ethernet@01c50000 {
-                       pinctrl-names = "default";
-                       pinctrl-0 = <&gmac_pins_rgmii_a>;
-                       phy = <&phy1>;
-                       phy-mode = "rgmii";
-                       status = "okay";
-
-                       phy1: ethernet-phy@1 {
-                               reg = <1>;
-                       };
-               };
-       };
-
        leds {
                compatible = "gpio-leds";
                pinctrl-names = "default";
@@ -223,26 +85,6 @@
                };
        };
 
-       reg_ahci_5v: ahci-5v {
-               pinctrl-0 = <&ahci_pwr_pin_cubietruck>;
-               gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
-               status = "okay";
-       };
-
-       reg_usb0_vbus: usb0-vbus {
-               pinctrl-0 = <&usb0_vbus_pin_a>;
-               gpio = <&pio 7 17 GPIO_ACTIVE_HIGH>;
-               status = "okay";
-       };
-
-       reg_usb1_vbus: usb1-vbus {
-               status = "okay";
-       };
-
-       reg_usb2_vbus: usb2-vbus {
-               status = "okay";
-       };
-
        reg_vmmc3: vmmc3 {
                compatible = "regulator-fixed";
                pinctrl-names = "default";
@@ -255,12 +97,141 @@
        };
 };
 
-#include "axp209.dtsi"
+&ahci {
+       target-supply = <&reg_ahci_5v>;
+       status = "okay";
+};
 
 &cpu0 {
        cpu-supply = <&reg_dcdc2>;
 };
 
+&ehci0 {
+       status = "okay";
+};
+
+&ehci1 {
+       status = "okay";
+};
+
+&gmac {
+       pinctrl-names = "default";
+       pinctrl-0 = <&gmac_pins_rgmii_a>;
+       phy = <&phy1>;
+       phy-mode = "rgmii";
+       status = "okay";
+
+       phy1: ethernet-phy@1 {
+               reg = <1>;
+       };
+};
+
+&i2c0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&i2c0_pins_a>;
+       status = "okay";
+
+       axp209: pmic@34 {
+               reg = <0x34>;
+               interrupt-parent = <&nmi_intc>;
+               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+       };
+};
+
+&i2c1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&i2c1_pins_a>;
+       status = "okay";
+};
+
+&i2c2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&i2c2_pins_a>;
+       status = "okay";
+};
+
+&ir0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&ir0_pins_a>;
+       status = "okay";
+};
+
+&mmc0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+       vmmc-supply = <&reg_vcc3v3>;
+       bus-width = <4>;
+       cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+       cd-inverted;
+       status = "okay";
+};
+
+&mmc3 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc3_pins_a>;
+       vmmc-supply = <&reg_vmmc3>;
+       bus-width = <4>;
+       non-removable;
+       status = "okay";
+};
+
+&mmc3_pins_a {
+       /* AP6210 requires pull-up */
+       allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&ohci0 {
+       status = "okay";
+};
+
+&ohci1 {
+       status = "okay";
+};
+
+&pio {
+       vmmc3_pin_cubietruck: vmmc3_pin@0 {
+               allwinner,pins = "PH9";
+               allwinner,function = "gpio_out";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       };
+
+       ahci_pwr_pin_cubietruck: ahci_pwr_pin@1 {
+               allwinner,pins = "PH12";
+               allwinner,function = "gpio_out";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       };
+
+       led_pins_cubietruck: led_pins@0 {
+               allwinner,pins = "PH7", "PH11", "PH20", "PH21";
+               allwinner,function = "gpio_out";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       };
+
+       usb0_vbus_pin_a: usb0_vbus_pin@0 {
+               allwinner,pins = "PH17";
+               allwinner,function = "gpio_out";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       };
+};
+
+&pwm {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pwm0_pins_a>, <&pwm1_pins_a>;
+       status = "okay";
+};
+
+&reg_ahci_5v {
+       pinctrl-0 = <&ahci_pwr_pin_cubietruck>;
+       gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
+       status = "okay";
+};
+
+#include "axp209.dtsi"
+
 &reg_dcdc2 {
        regulator-always-on;
        regulator-min-microvolt = <1000000>;
@@ -285,3 +256,30 @@
        regulator-max-microvolt = <3000000>;
        regulator-name = "avcc";
 };
+
+&reg_usb0_vbus {
+       pinctrl-0 = <&usb0_vbus_pin_a>;
+       gpio = <&pio 7 17 GPIO_ACTIVE_HIGH>;
+       status = "okay";
+};
+
+&reg_usb1_vbus {
+       status = "okay";
+};
+
+&reg_usb2_vbus {
+       status = "okay";
+};
+
+&uart0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart0_pins_a>;
+       status = "okay";
+};
+
+&usbphy {
+       usb0_vbus-supply = <&reg_usb0_vbus>;
+       usb1_vbus-supply = <&reg_usb1_vbus>;
+       usb2_vbus-supply = <&reg_usb2_vbus>;
+       status = "okay";
+};