S: Maintained
F: drivers/mtd/devices/phram.c
+PICOXCELL SUPPORT
+M: Jamie Iles <jamie@jamieiles.com>
+L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+T: git git://github.com/jamieiles/linux-2.6-ji.git
+S: Supported
+F: arch/arm/mach-picoxcell
+F: drivers/*/picoxcell*
+F: drivers/*/*/picoxcell*
+
PIN CONTROL SUBSYSTEM
M: Linus Walleij <linus.walleij@linaro.org>
S: Maintained
select HAVE_SCHED_CLOCK
select HAVE_TCM
select NO_IOPORT
+ select SPARSE_IRQ
select USE_OF
help
This enables support for systems based on the Picochip picoXcell
select HAVE_MACH_CLKDEV
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
- select NEED_MACH_MEMORY_H
help
Support for ST-Ericsson U300 series mobile platforms.
Note that the system will appear to hang during boot if there
is nothing connected to read from the DCC.
+ config AT91_DEBUG_LL_DBGU0
+ bool "Kernel low-level debugging on rm9200, 9260/9g20, 9261/9g10 and 9rl"
+ depends on HAVE_AT91_DBGU0
+
+ config AT91_DEBUG_LL_DBGU1
+ bool "Kernel low-level debugging on 9263, 9g45 and cap9"
+ depends on HAVE_AT91_DBGU1
+
config DEBUG_FOOTBRIDGE_COM1
bool "Kernel low-level debugging messages via footbridge 8250 at PCI COM1"
depends on FOOTBRIDGE
their output to the standard serial port on the RealView
PB1176 platform.
+ config DEBUG_MSM_UART1
+ bool "Kernel low-level debugging messages via MSM UART1"
+ depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the first serial port on MSM devices.
+
+ config DEBUG_MSM_UART2
+ bool "Kernel low-level debugging messages via MSM UART2"
+ depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the second serial port on MSM devices.
+
+ config DEBUG_MSM_UART3
+ bool "Kernel low-level debugging messages via MSM UART3"
+ depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the third serial port on MSM devices.
+
+ config DEBUG_MSM8660_UART
+ bool "Kernel low-level debugging messages via MSM 8660 UART"
+ depends on ARCH_MSM8X60
+ select MSM_HAS_DEBUG_UART_HS
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the serial port on MSM 8660 devices.
+
+ config DEBUG_MSM8960_UART
+ bool "Kernel low-level debugging messages via MSM 8960 UART"
+ depends on ARCH_MSM8960
+ select MSM_HAS_DEBUG_UART_HS
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the serial port on MSM 8960 devices.
+
endchoice
config EARLY_PRINTK
+++ /dev/null
-CONFIG_EXPERIMENTAL=y
-CONFIG_CROSS_COMPILE="/opt/arm-2010q1/bin/arm-none-linux-gnueabi-"
-# CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_TREE_PREEMPT_RCU=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_NAMESPACES=y
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EXPERT=y
-# CONFIG_SYSCTL_SYSCALL is not set
-# CONFIG_KALLSYMS is not set
-# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_LBDAF is not set
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_DEFAULT_DEADLINE=y
-CONFIG_ARCH_AT91=y
-CONFIG_ARCH_AT91SAM9G20=y
-CONFIG_MACH_PCONTROL_G20=y
-CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_PREEMPT=y
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=ttyS0,115200 mem=128M mtdparts=atmel_nand:128k(bootstrap)ro,256k(uboot)ro,128k(env1)ro,128k(env2)ro,2M(linux),-(root) root=/dev/mmcblk0p1 rootwait rw"
-CONFIG_VFP=y
-CONFIG_BINFMT_MISC=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_IPV6 is not set
-CONFIG_VLAN_8021Q=y
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-# CONFIG_FW_LOADER is not set
-CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_COMPLEX_MAPPINGS=y
-CONFIG_MTD_PHRAM=m
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ATMEL=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_ATMEL_TCLIB=y
-CONFIG_EEPROM_AT24=m
-CONFIG_SCSI=m
-# CONFIG_SCSI_PROC_FS is not set
-CONFIG_BLK_DEV_SD=m
-CONFIG_SCSI_MULTI_LUN=y
-# CONFIG_SCSI_LOWLEVEL is not set
-CONFIG_NETDEVICES=y
-CONFIG_MACVLAN=m
-CONFIG_TUN=m
-CONFIG_SMSC_PHY=m
-CONFIG_BROADCOM_PHY=m
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-CONFIG_MACB=y
-CONFIG_SMSC911X=m
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-# CONFIG_WLAN is not set
-CONFIG_PPP=m
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPP_MPPE=m
-CONFIG_INPUT_POLLDEV=y
-CONFIG_INPUT_SPARSEKMAP=y
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=m
-CONFIG_INPUT_EVBUG=m
-# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_KEYBOARD_GPIO=m
-CONFIG_KEYBOARD_MATRIX=m
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_INPUT_MISC=y
-CONFIG_INPUT_UINPUT=m
-CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
-# CONFIG_SERIO is not set
-# CONFIG_DEVKMEM is not set
-CONFIG_SERIAL_ATMEL=y
-CONFIG_SERIAL_ATMEL_CONSOLE=y
-CONFIG_SERIAL_MAX3100=m
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_HW_RANDOM is not set
-CONFIG_R3964=m
-CONFIG_I2C=m
-CONFIG_I2C_CHARDEV=m
-# CONFIG_I2C_HELPER_AUTO is not set
-CONFIG_I2C_GPIO=m
-CONFIG_SPI=y
-CONFIG_SPI_ATMEL=m
-CONFIG_SPI_SPIDEV=m
-CONFIG_GPIO_SYSFS=y
-CONFIG_W1=m
-CONFIG_W1_MASTER_GPIO=m
-CONFIG_W1_SLAVE_DS2431=m
-# CONFIG_HWMON is not set
-CONFIG_WATCHDOG=y
-CONFIG_AT91SAM9X_WATCHDOG=y
-# CONFIG_MFD_SUPPORT is not set
-# CONFIG_HID_SUPPORT is not set
-CONFIG_USB=y
-# CONFIG_USB_DEVICE_CLASS is not set
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=m
-CONFIG_USB_LIBUSUAL=y
-CONFIG_USB_SERIAL=m
-CONFIG_USB_SERIAL_GENERIC=y
-CONFIG_USB_SERIAL_FTDI_SIO=m
-CONFIG_USB_SERIAL_PL2303=m
-CONFIG_USB_GADGET=y
-CONFIG_USB_ZERO=m
-CONFIG_USB_ETH=m
-CONFIG_USB_FILE_STORAGE=m
-CONFIG_USB_G_SERIAL=m
-CONFIG_USB_G_HID=m
-CONFIG_MMC=y
-CONFIG_MMC_UNSAFE_RESUME=y
-CONFIG_MMC_ATMELMCI=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_TIMER=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_AT91SAM9=y
-CONFIG_AUXDISPLAY=y
-CONFIG_UIO=y
-CONFIG_UIO_PDRV=y
-CONFIG_STAGING=y
-# CONFIG_STAGING_EXCLUDE_BUILD is not set
-CONFIG_IIO=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-# CONFIG_EXT3_FS_XATTR is not set
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V4=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_ISO8859_15=y
-CONFIG_NLS_UTF8=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ANSI_CPRNG=y
-# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC_CCITT=y
config HAVE_AT91_DATAFLASH_CARD
bool
+config HAVE_AT91_DBGU0
+ bool
+
+config HAVE_AT91_DBGU1
+ bool
+
config HAVE_AT91_USART3
bool
bool "AT91RM9200"
select CPU_ARM920T
select GENERIC_CLOCKEVENTS
+ select HAVE_AT91_DBGU0
select HAVE_AT91_USART3
config ARCH_AT91SAM9260
bool "AT91SAM9260 or AT91SAM9XE"
select CPU_ARM926T
select GENERIC_CLOCKEVENTS
+ select HAVE_AT91_DBGU0
select HAVE_AT91_USART3
select HAVE_AT91_USART4
select HAVE_AT91_USART5
select CPU_ARM926T
select GENERIC_CLOCKEVENTS
select HAVE_FB_ATMEL
+ select HAVE_AT91_DBGU0
config ARCH_AT91SAM9G10
bool "AT91SAM9G10"
select CPU_ARM926T
select GENERIC_CLOCKEVENTS
+ select HAVE_AT91_DBGU0
select HAVE_FB_ATMEL
config ARCH_AT91SAM9263
select GENERIC_CLOCKEVENTS
select HAVE_FB_ATMEL
select HAVE_NET_MACB
+ select HAVE_AT91_DBGU1
config ARCH_AT91SAM9RL
bool "AT91SAM9RL"
select GENERIC_CLOCKEVENTS
select HAVE_AT91_USART3
select HAVE_FB_ATMEL
+ select HAVE_AT91_DBGU0
config ARCH_AT91SAM9G20
bool "AT91SAM9G20"
select CPU_ARM926T
select GENERIC_CLOCKEVENTS
+ select HAVE_AT91_DBGU0
select HAVE_AT91_USART3
select HAVE_AT91_USART4
select HAVE_AT91_USART5
select HAVE_AT91_USART3
select HAVE_FB_ATMEL
select HAVE_NET_MACB
+ select HAVE_AT91_DBGU1
config ARCH_AT91CAP9
bool "AT91CAP9"
select GENERIC_CLOCKEVENTS
select HAVE_FB_ATMEL
select HAVE_NET_MACB
+ select HAVE_AT91_DBGU1
config ARCH_AT91X40
bool "AT91x40"
choice
prompt "Select a UART for early kernel messages"
-config AT91_EARLY_DBGU
- bool "DBGU"
+config AT91_EARLY_DBGU0
+ bool "DBGU on rm9200, 9260/9g20, 9261/9g10 and 9rl"
+ depends on HAVE_AT91_DBGU0
+
+config AT91_EARLY_DBGU1
+ bool "DBGU on 9263, 9g45 and cap9"
+ depends on HAVE_AT91_DBGU1
config AT91_EARLY_USART0
bool "USART0"
*/
#include <linux/module.h>
-#include <linux/pm.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <mach/at91cap9.h>
#include <mach/at91_pmc.h>
#include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
#include "soc.h"
#include "generic.h"
#include "clock.h"
+#include "sam9_smc.h"
/* --------------------------------------------------------------------
* Clocks
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk macb_clk = {
- .name = "macb_clk",
+ .name = "pclk",
.pmc_mask = 1 << AT91CAP9_ID_EMAC,
.type = CLK_TYPE_PERIPHERAL,
};
};
static struct clk_lookup periph_clocks_lookups[] = {
+ /* One additional fake clock for macb_hclk */
+ CLKDEV_CON_ID("hclk", &macb_clk),
CLKDEV_CON_DEV_ID("hclk", "atmel_usba_udc", &utmi_clk),
CLKDEV_CON_DEV_ID("pclk", "atmel_usba_udc", &udphs_clk),
CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk),
CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
/* fake hclk clock */
CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
+ CLKDEV_CON_ID("pioA", &pioABCD_clk),
+ CLKDEV_CON_ID("pioB", &pioABCD_clk),
+ CLKDEV_CON_ID("pioC", &pioABCD_clk),
+ CLKDEV_CON_ID("pioD", &pioABCD_clk),
};
static struct clk_lookup usart_clocks_lookups[] = {
* GPIO
* -------------------------------------------------------------------- */
-static struct at91_gpio_bank at91cap9_gpio[] = {
+static struct at91_gpio_bank at91cap9_gpio[] __initdata = {
{
.id = AT91CAP9_ID_PIOABCD,
- .offset = AT91_PIOA,
- .clock = &pioABCD_clk,
+ .regbase = AT91CAP9_BASE_PIOA,
}, {
.id = AT91CAP9_ID_PIOABCD,
- .offset = AT91_PIOB,
- .clock = &pioABCD_clk,
+ .regbase = AT91CAP9_BASE_PIOB,
}, {
.id = AT91CAP9_ID_PIOABCD,
- .offset = AT91_PIOC,
- .clock = &pioABCD_clk,
+ .regbase = AT91CAP9_BASE_PIOC,
}, {
.id = AT91CAP9_ID_PIOABCD,
- .offset = AT91_PIOD,
- .clock = &pioABCD_clk,
+ .regbase = AT91CAP9_BASE_PIOD,
}
};
at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
}
-static void at91cap9_poweroff(void)
-{
- at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
/* --------------------------------------------------------------------
* AT91CAP9 processor initialization
* -------------------------------------------------------------------- */
at91_init_sram(0, AT91CAP9_SRAM_BASE, AT91CAP9_SRAM_SIZE);
}
+static void __init at91cap9_ioremap_registers(void)
+{
+ at91_ioremap_shdwc(AT91CAP9_BASE_SHDWC);
+ at91sam926x_ioremap_pit(AT91CAP9_BASE_PIT);
+ at91sam9_ioremap_smc(0, AT91CAP9_BASE_SMC);
+}
+
static void __init at91cap9_initialize(void)
{
arm_pm_restart = at91cap9_restart;
- pm_power_off = at91cap9_poweroff;
at91_extern_irq = (1 << AT91CAP9_ID_IRQ0) | (1 << AT91CAP9_ID_IRQ1);
/* Register GPIO subsystem */
struct at91_init_soc __initdata at91cap9_soc = {
.map_io = at91cap9_map_io,
.default_irq_priority = at91cap9_default_irq_priority,
+ .ioremap_registers = at91cap9_ioremap_registers,
.register_clocks = at91cap9_register_clocks,
.init = at91cap9_initialize,
};
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
- if (data->vbus_pin[i])
+ if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i], 0);
}
usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
- if (data && data->vbus_pin > 0) {
+ if (data && gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
usba_udc_data.pdata.vbus_pin = data->vbus_pin;
#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
static struct resource eth_resources[] = {
[0] = {
.num_resources = ARRAY_SIZE(eth_resources),
};
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
{
if (!data)
return;
- if (data->phy_irq_pin) {
+ if (gpio_is_valid(data->phy_irq_pin)) {
at91_set_gpio_input(data->phy_irq_pin, 0);
at91_set_deglitch(data->phy_irq_pin, 1);
}
platform_device_register(&at91cap9_eth_device);
}
#else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
#endif
return;
/* input/irq */
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
- if (data->wp_pin)
+ if (gpio_is_valid(data->wp_pin))
at91_set_gpio_input(data->wp_pin, 1);
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
if (mmc_id == 0) { /* MCI0 */
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91_BASE_SYS + AT91_ECC,
- .end = AT91_BASE_SYS + AT91_ECC + SZ_512 - 1,
+ .start = AT91CAP9_BASE_ECC,
+ .end = AT91CAP9_BASE_ECC + SZ_512 - 1,
.flags = IORESOURCE_MEM,
}
};
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
nand_data = *data;
static struct resource rtt_resources[] = {
{
- .start = AT91_BASE_SYS + AT91_RTT,
- .end = AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+ .start = AT91CAP9_BASE_RTT,
+ .end = AT91CAP9_BASE_RTT + SZ_16 - 1,
.flags = IORESOURCE_MEM,
}
};
* -------------------------------------------------------------------- */
#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+ {
+ .start = AT91CAP9_BASE_WDT,
+ .end = AT91CAP9_BASE_WDT + SZ_16 - 1,
+ .flags = IORESOURCE_MEM,
+ }
+};
+
static struct platform_device at91cap9_wdt_device = {
.name = "at91_wdt",
.id = -1,
- .num_resources = 0,
+ .resource = wdt_resources,
+ .num_resources = ARRAY_SIZE(wdt_resources),
};
static void __init at91_add_device_watchdog(void)
at91_set_A_periph(AT91_PIN_PA9, 0); /* AC97RX */
/* reset */
- if (data->reset_pin)
+ if (gpio_is_valid(data->reset_pin))
at91_set_gpio_output(data->reset_pin, 0);
ac97_data = *data;
#if defined(CONFIG_SERIAL_ATMEL)
static struct resource dbgu_resources[] = {
[0] = {
- .start = AT91_BASE_SYS + AT91_DBGU,
- .end = AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+ .start = AT91CAP9_BASE_DBGU,
+ .end = AT91CAP9_BASE_DBGU + SZ_512 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
#include "soc.h"
#include "generic.h"
#include "clock.h"
+#include "sam9_smc.h"
static struct map_desc at91rm9200_io_desc[] __initdata = {
{
CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk),
/* fake hclk clock */
CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
+ CLKDEV_CON_ID("pioA", &pioA_clk),
+ CLKDEV_CON_ID("pioB", &pioB_clk),
+ CLKDEV_CON_ID("pioC", &pioC_clk),
+ CLKDEV_CON_ID("pioD", &pioD_clk),
};
static struct clk_lookup usart_clocks_lookups[] = {
* GPIO
* -------------------------------------------------------------------- */
-static struct at91_gpio_bank at91rm9200_gpio[] = {
+static struct at91_gpio_bank at91rm9200_gpio[] __initdata = {
{
.id = AT91RM9200_ID_PIOA,
- .offset = AT91_PIOA,
- .clock = &pioA_clk,
+ .regbase = AT91RM9200_BASE_PIOA,
}, {
.id = AT91RM9200_ID_PIOB,
- .offset = AT91_PIOB,
- .clock = &pioB_clk,
+ .regbase = AT91RM9200_BASE_PIOB,
}, {
.id = AT91RM9200_ID_PIOC,
- .offset = AT91_PIOC,
- .clock = &pioC_clk,
+ .regbase = AT91RM9200_BASE_PIOC,
}, {
.id = AT91RM9200_ID_PIOD,
- .offset = AT91_PIOD,
- .clock = &pioD_clk,
+ .regbase = AT91RM9200_BASE_PIOD,
}
};
iotable_init(at91rm9200_io_desc, ARRAY_SIZE(at91rm9200_io_desc));
}
+static void __init at91rm9200_ioremap_registers(void)
+{
+}
+
static void __init at91rm9200_initialize(void)
{
arm_pm_restart = at91rm9200_restart;
struct at91_init_soc __initdata at91rm9200_soc = {
.map_io = at91rm9200_map_io,
.default_irq_priority = at91rm9200_default_irq_priority,
+ .ioremap_registers = at91rm9200_ioremap_registers,
.register_clocks = at91rm9200_register_clocks,
.init = at91rm9200_initialize,
};
if (!data)
return;
- if (data->vbus_pin) {
+ if (gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
}
- if (data->pullup_pin)
+ if (gpio_is_valid(data->pullup_pin))
at91_set_gpio_output(data->pullup_pin, 0);
udc_data = *data;
#if defined(CONFIG_ARM_AT91_ETHER) || defined(CONFIG_ARM_AT91_ETHER_MODULE)
static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
static struct resource eth_resources[] = {
[0] = {
.num_resources = ARRAY_SIZE(eth_resources),
};
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
{
if (!data)
return;
- if (data->phy_irq_pin) {
+ if (gpio_is_valid(data->phy_irq_pin)) {
at91_set_gpio_input(data->phy_irq_pin, 0);
at91_set_deglitch(data->phy_irq_pin, 1);
}
platform_device_register(&at91rm9200_eth_device);
}
#else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
#endif
);
/* input/irq */
- if (data->irq_pin) {
+ if (gpio_is_valid(data->irq_pin)) {
at91_set_gpio_input(data->irq_pin, 1);
at91_set_deglitch(data->irq_pin, 1);
}
at91_set_deglitch(data->det_pin, 1);
/* outputs, initially off */
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
at91_set_gpio_output(data->rst_pin, 0);
return;
/* input/irq */
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
- if (data->wp_pin)
+ if (gpio_is_valid(data->wp_pin))
at91_set_gpio_input(data->wp_pin, 1);
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
/* CLK */
);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
at91_set_A_periph(AT91_PIN_PC1, 0); /* SMOE */
* -------------------------------------------------------------------- */
#if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE)
+static struct resource rtc_resources[] = {
+ [0] = {
+ .start = AT91RM9200_BASE_RTC,
+ .end = AT91RM9200_BASE_RTC + SZ_256 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91_ID_SYS,
+ .end = AT91_ID_SYS,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
static struct platform_device at91rm9200_rtc_device = {
.name = "at91_rtc",
.id = -1,
- .num_resources = 0,
+ .resource = rtc_resources,
+ .num_resources = ARRAY_SIZE(rtc_resources),
};
static void __init at91_add_device_rtc(void)
#if defined(CONFIG_SERIAL_ATMEL)
static struct resource dbgu_resources[] = {
[0] = {
- .start = AT91_BASE_SYS + AT91_DBGU,
- .end = AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+ .start = AT91RM9200_BASE_DBGU,
+ .end = AT91RM9200_BASE_DBGU + SZ_512 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
static u32 irqmask;
static struct clock_event_device clkevt;
+#define RM9200_TIMER_LATCH ((AT91_SLOW_CLOCK + HZ/2) / HZ)
+
/*
* The ST_CRTR is updated asynchronously to the master clock ... but
* the updates as seen by the CPU don't seem to be strictly monotonic.
if (sr & AT91_ST_PITS) {
u32 crtr = read_CRTR();
- while (((crtr - last_crtr) & AT91_ST_CRTV) >= LATCH) {
- last_crtr += LATCH;
+ while (((crtr - last_crtr) & AT91_ST_CRTV) >= RM9200_TIMER_LATCH) {
+ last_crtr += RM9200_TIMER_LATCH;
clkevt.event_handler(&clkevt);
}
return IRQ_HANDLED;
case CLOCK_EVT_MODE_PERIODIC:
/* PIT for periodic irqs; fixed rate of 1/HZ */
irqmask = AT91_ST_PITS;
- at91_sys_write(AT91_ST_PIMR, LATCH);
+ at91_sys_write(AT91_ST_PIMR, RM9200_TIMER_LATCH);
break;
case CLOCK_EVT_MODE_ONESHOT:
/* ALM for oneshot irqs, set by next_event()
*/
#include <linux/module.h>
-#include <linux/pm.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <mach/at91sam9260.h>
#include <mach/at91_pmc.h>
#include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
#include "soc.h"
#include "generic.h"
#include "clock.h"
+#include "sam9_smc.h"
/* --------------------------------------------------------------------
* Clocks
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk macb_clk = {
- .name = "macb_clk",
+ .name = "pclk",
.pmc_mask = 1 << AT91SAM9260_ID_EMAC,
.type = CLK_TYPE_PERIPHERAL,
};
};
static struct clk_lookup periph_clocks_lookups[] = {
+ /* One additional fake clock for macb_hclk */
+ CLKDEV_CON_ID("hclk", &macb_clk),
CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
CLKDEV_CON_DEV_ID("usart", "fffd8000.serial", &usart5_clk),
/* fake hclk clock */
CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
+ CLKDEV_CON_ID("pioA", &pioA_clk),
+ CLKDEV_CON_ID("pioB", &pioB_clk),
+ CLKDEV_CON_ID("pioC", &pioC_clk),
};
static struct clk_lookup usart_clocks_lookups[] = {
* GPIO
* -------------------------------------------------------------------- */
-static struct at91_gpio_bank at91sam9260_gpio[] = {
+static struct at91_gpio_bank at91sam9260_gpio[] __initdata = {
{
.id = AT91SAM9260_ID_PIOA,
- .offset = AT91_PIOA,
- .clock = &pioA_clk,
+ .regbase = AT91SAM9260_BASE_PIOA,
}, {
.id = AT91SAM9260_ID_PIOB,
- .offset = AT91_PIOB,
- .clock = &pioB_clk,
+ .regbase = AT91SAM9260_BASE_PIOB,
}, {
.id = AT91SAM9260_ID_PIOC,
- .offset = AT91_PIOC,
- .clock = &pioC_clk,
+ .regbase = AT91SAM9260_BASE_PIOC,
}
};
-static void at91sam9260_poweroff(void)
-{
- at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
/* --------------------------------------------------------------------
* AT91SAM9260 processor initialization
* -------------------------------------------------------------------- */
}
}
+static void __init at91sam9260_ioremap_registers(void)
+{
+ at91_ioremap_shdwc(AT91SAM9260_BASE_SHDWC);
+ at91sam926x_ioremap_pit(AT91SAM9260_BASE_PIT);
+ at91sam9_ioremap_smc(0, AT91SAM9260_BASE_SMC);
+}
+
static void __init at91sam9260_initialize(void)
{
arm_pm_restart = at91sam9_alt_restart;
- pm_power_off = at91sam9260_poweroff;
at91_extern_irq = (1 << AT91SAM9260_ID_IRQ0) | (1 << AT91SAM9260_ID_IRQ1)
| (1 << AT91SAM9260_ID_IRQ2);
struct at91_init_soc __initdata at91sam9260_soc = {
.map_io = at91sam9260_map_io,
.default_irq_priority = at91sam9260_default_irq_priority,
+ .ioremap_registers = at91sam9260_ioremap_registers,
.register_clocks = at91sam9260_register_clocks,
.init = at91sam9260_initialize,
};
if (!data)
return;
- if (data->vbus_pin) {
+ if (gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
}
#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
static struct resource eth_resources[] = {
[0] = {
.num_resources = ARRAY_SIZE(eth_resources),
};
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
{
if (!data)
return;
- if (data->phy_irq_pin) {
+ if (gpio_is_valid(data->phy_irq_pin)) {
at91_set_gpio_input(data->phy_irq_pin, 0);
at91_set_deglitch(data->phy_irq_pin, 1);
}
platform_device_register(&at91sam9260_eth_device);
}
#else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
#endif
return;
/* input/irq */
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
- if (data->wp_pin)
+ if (gpio_is_valid(data->wp_pin))
at91_set_gpio_input(data->wp_pin, 1);
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
/* CLK */
for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
if (data->slot[i].bus_width) {
/* input/irq */
- if (data->slot[i].detect_pin) {
+ if (gpio_is_valid(data->slot[i].detect_pin)) {
at91_set_gpio_input(data->slot[i].detect_pin, 1);
at91_set_deglitch(data->slot[i].detect_pin, 1);
}
- if (data->slot[i].wp_pin)
+ if (gpio_is_valid(data->slot[i].wp_pin))
at91_set_gpio_input(data->slot[i].wp_pin, 1);
switch (i) {
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91_BASE_SYS + AT91_ECC,
- .end = AT91_BASE_SYS + AT91_ECC + SZ_512 - 1,
+ .start = AT91SAM9260_BASE_ECC,
+ .end = AT91SAM9260_BASE_ECC + SZ_512 - 1,
.flags = IORESOURCE_MEM,
}
};
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
nand_data = *data;
static struct resource rtt_resources[] = {
{
- .start = AT91_BASE_SYS + AT91_RTT,
- .end = AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+ .start = AT91SAM9260_BASE_RTT,
+ .end = AT91SAM9260_BASE_RTT + SZ_16 - 1,
.flags = IORESOURCE_MEM,
}
};
* -------------------------------------------------------------------- */
#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+ {
+ .start = AT91SAM9260_BASE_WDT,
+ .end = AT91SAM9260_BASE_WDT + SZ_16 - 1,
+ .flags = IORESOURCE_MEM,
+ }
+};
+
static struct platform_device at91sam9260_wdt_device = {
.name = "at91_wdt",
.id = -1,
- .num_resources = 0,
+ .resource = wdt_resources,
+ .num_resources = ARRAY_SIZE(wdt_resources),
};
static void __init at91_add_device_watchdog(void)
#if defined(CONFIG_SERIAL_ATMEL)
static struct resource dbgu_resources[] = {
[0] = {
- .start = AT91_BASE_SYS + AT91_DBGU,
- .end = AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+ .start = AT91SAM9260_BASE_DBGU,
+ .end = AT91SAM9260_BASE_DBGU + SZ_512 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
at91_sys_write(AT91_MATRIX_EBICSA, csa);
- if (data->rst_pin) {
+ if (gpio_is_valid(data->rst_pin)) {
at91_set_multi_drive(data->rst_pin, 0);
at91_set_gpio_output(data->rst_pin, 1);
}
- if (data->irq_pin) {
+ if (gpio_is_valid(data->irq_pin)) {
at91_set_gpio_input(data->irq_pin, 0);
at91_set_deglitch(data->irq_pin, 1);
}
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 0);
at91_set_deglitch(data->det_pin, 1);
}
*/
#include <linux/module.h>
-#include <linux/pm.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <mach/at91sam9261.h>
#include <mach/at91_pmc.h>
#include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
#include "soc.h"
#include "generic.h"
#include "clock.h"
+#include "sam9_smc.h"
/* --------------------------------------------------------------------
* Clocks
CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk),
CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &hck0),
+ CLKDEV_CON_ID("pioA", &pioA_clk),
+ CLKDEV_CON_ID("pioB", &pioB_clk),
+ CLKDEV_CON_ID("pioC", &pioC_clk),
};
static struct clk_lookup usart_clocks_lookups[] = {
* GPIO
* -------------------------------------------------------------------- */
-static struct at91_gpio_bank at91sam9261_gpio[] = {
+static struct at91_gpio_bank at91sam9261_gpio[] __initdata = {
{
.id = AT91SAM9261_ID_PIOA,
- .offset = AT91_PIOA,
- .clock = &pioA_clk,
+ .regbase = AT91SAM9261_BASE_PIOA,
}, {
.id = AT91SAM9261_ID_PIOB,
- .offset = AT91_PIOB,
- .clock = &pioB_clk,
+ .regbase = AT91SAM9261_BASE_PIOB,
}, {
.id = AT91SAM9261_ID_PIOC,
- .offset = AT91_PIOC,
- .clock = &pioC_clk,
+ .regbase = AT91SAM9261_BASE_PIOC,
}
};
-static void at91sam9261_poweroff(void)
-{
- at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
/* --------------------------------------------------------------------
* AT91SAM9261 processor initialization
* -------------------------------------------------------------------- */
at91_init_sram(0, AT91SAM9261_SRAM_BASE, AT91SAM9261_SRAM_SIZE);
}
+static void __init at91sam9261_ioremap_registers(void)
+{
+ at91_ioremap_shdwc(AT91SAM9261_BASE_SHDWC);
+ at91sam926x_ioremap_pit(AT91SAM9261_BASE_PIT);
+ at91sam9_ioremap_smc(0, AT91SAM9261_BASE_SMC);
+}
+
static void __init at91sam9261_initialize(void)
{
arm_pm_restart = at91sam9_alt_restart;
- pm_power_off = at91sam9261_poweroff;
at91_extern_irq = (1 << AT91SAM9261_ID_IRQ0) | (1 << AT91SAM9261_ID_IRQ1)
| (1 << AT91SAM9261_ID_IRQ2);
struct at91_init_soc __initdata at91sam9261_soc = {
.map_io = at91sam9261_map_io,
.default_irq_priority = at91sam9261_default_irq_priority,
+ .ioremap_registers = at91sam9261_ioremap_registers,
.register_clocks = at91sam9261_register_clocks,
.init = at91sam9261_initialize,
};
if (!data)
return;
- if (data->vbus_pin) {
+ if (gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
}
return;
/* input/irq */
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
- if (data->wp_pin)
+ if (gpio_is_valid(data->wp_pin))
at91_set_gpio_input(data->wp_pin, 1);
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
/* CLK */
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
at91_set_A_periph(AT91_PIN_PC0, 0); /* NANDOE */
static struct resource rtt_resources[] = {
{
- .start = AT91_BASE_SYS + AT91_RTT,
- .end = AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+ .start = AT91SAM9261_BASE_RTT,
+ .end = AT91SAM9261_BASE_RTT + SZ_16 - 1,
.flags = IORESOURCE_MEM,
}
};
* -------------------------------------------------------------------- */
#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+ {
+ .start = AT91SAM9261_BASE_WDT,
+ .end = AT91SAM9261_BASE_WDT + SZ_16 - 1,
+ .flags = IORESOURCE_MEM,
+ }
+};
+
static struct platform_device at91sam9261_wdt_device = {
.name = "at91_wdt",
.id = -1,
- .num_resources = 0,
+ .resource = wdt_resources,
+ .num_resources = ARRAY_SIZE(wdt_resources),
};
static void __init at91_add_device_watchdog(void)
#if defined(CONFIG_SERIAL_ATMEL)
static struct resource dbgu_resources[] = {
[0] = {
- .start = AT91_BASE_SYS + AT91_DBGU,
- .end = AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+ .start = AT91SAM9261_BASE_DBGU,
+ .end = AT91SAM9261_BASE_DBGU + SZ_512 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
*/
#include <linux/module.h>
-#include <linux/pm.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <mach/at91sam9263.h>
#include <mach/at91_pmc.h>
#include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
#include "soc.h"
#include "generic.h"
#include "clock.h"
+#include "sam9_smc.h"
/* --------------------------------------------------------------------
* Clocks
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk macb_clk = {
- .name = "macb_clk",
+ .name = "pclk",
.pmc_mask = 1 << AT91SAM9263_ID_EMAC,
.type = CLK_TYPE_PERIPHERAL,
};
};
static struct clk_lookup periph_clocks_lookups[] = {
+ /* One additional fake clock for macb_hclk */
+ CLKDEV_CON_ID("hclk", &macb_clk),
CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk),
CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk),
/* fake hclk clock */
CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
+ CLKDEV_CON_ID("pioA", &pioA_clk),
+ CLKDEV_CON_ID("pioB", &pioB_clk),
+ CLKDEV_CON_ID("pioC", &pioCDE_clk),
+ CLKDEV_CON_ID("pioD", &pioCDE_clk),
+ CLKDEV_CON_ID("pioE", &pioCDE_clk),
};
static struct clk_lookup usart_clocks_lookups[] = {
* GPIO
* -------------------------------------------------------------------- */
-static struct at91_gpio_bank at91sam9263_gpio[] = {
+static struct at91_gpio_bank at91sam9263_gpio[] __initdata = {
{
.id = AT91SAM9263_ID_PIOA,
- .offset = AT91_PIOA,
- .clock = &pioA_clk,
+ .regbase = AT91SAM9263_BASE_PIOA,
}, {
.id = AT91SAM9263_ID_PIOB,
- .offset = AT91_PIOB,
- .clock = &pioB_clk,
+ .regbase = AT91SAM9263_BASE_PIOB,
}, {
.id = AT91SAM9263_ID_PIOCDE,
- .offset = AT91_PIOC,
- .clock = &pioCDE_clk,
+ .regbase = AT91SAM9263_BASE_PIOC,
}, {
.id = AT91SAM9263_ID_PIOCDE,
- .offset = AT91_PIOD,
- .clock = &pioCDE_clk,
+ .regbase = AT91SAM9263_BASE_PIOD,
}, {
.id = AT91SAM9263_ID_PIOCDE,
- .offset = AT91_PIOE,
- .clock = &pioCDE_clk,
+ .regbase = AT91SAM9263_BASE_PIOE,
}
};
-static void at91sam9263_poweroff(void)
-{
- at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
/* --------------------------------------------------------------------
* AT91SAM9263 processor initialization
* -------------------------------------------------------------------- */
at91_init_sram(1, AT91SAM9263_SRAM1_BASE, AT91SAM9263_SRAM1_SIZE);
}
+static void __init at91sam9263_ioremap_registers(void)
+{
+ at91_ioremap_shdwc(AT91SAM9263_BASE_SHDWC);
+ at91sam926x_ioremap_pit(AT91SAM9263_BASE_PIT);
+ at91sam9_ioremap_smc(0, AT91SAM9263_BASE_SMC0);
+ at91sam9_ioremap_smc(1, AT91SAM9263_BASE_SMC1);
+}
+
static void __init at91sam9263_initialize(void)
{
arm_pm_restart = at91sam9_alt_restart;
- pm_power_off = at91sam9263_poweroff;
at91_extern_irq = (1 << AT91SAM9263_ID_IRQ0) | (1 << AT91SAM9263_ID_IRQ1);
/* Register GPIO subsystem */
struct at91_init_soc __initdata at91sam9263_soc = {
.map_io = at91sam9263_map_io,
.default_irq_priority = at91sam9263_default_irq_priority,
+ .ioremap_registers = at91sam9263_ioremap_registers,
.register_clocks = at91sam9263_register_clocks,
.init = at91sam9263_initialize,
};
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
- if (data->vbus_pin[i])
+ if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i], 0);
}
if (!data)
return;
- if (data->vbus_pin) {
+ if (gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
}
#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
static struct resource eth_resources[] = {
[0] = {
.num_resources = ARRAY_SIZE(eth_resources),
};
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
{
if (!data)
return;
- if (data->phy_irq_pin) {
+ if (gpio_is_valid(data->phy_irq_pin)) {
at91_set_gpio_input(data->phy_irq_pin, 0);
at91_set_deglitch(data->phy_irq_pin, 1);
}
platform_device_register(&at91sam9263_eth_device);
}
#else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
#endif
return;
/* input/irq */
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
- if (data->wp_pin)
+ if (gpio_is_valid(data->wp_pin))
at91_set_gpio_input(data->wp_pin, 1);
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
if (mmc_id == 0) { /* MCI0 */
}
at91_sys_write(AT91_MATRIX_EBI0CSA, ebi0_csa);
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
- if (data->irq_pin) {
+ if (gpio_is_valid(data->irq_pin)) {
at91_set_gpio_input(data->irq_pin, 1);
at91_set_deglitch(data->irq_pin, 1);
}
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
/* initially off */
at91_set_gpio_output(data->vcc_pin, 0);
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91_BASE_SYS + AT91_ECC0,
- .end = AT91_BASE_SYS + AT91_ECC0 + SZ_512 - 1,
+ .start = AT91SAM9263_BASE_ECC0,
+ .end = AT91SAM9263_BASE_ECC0 + SZ_512 - 1,
.flags = IORESOURCE_MEM,
}
};
at91_sys_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
nand_data = *data;
at91_set_A_periph(AT91_PIN_PB3, 0); /* AC97RX */
/* reset */
- if (data->reset_pin)
+ if (gpio_is_valid(data->reset_pin))
at91_set_gpio_output(data->reset_pin, 0);
ac97_data = *data;
static struct resource rtt0_resources[] = {
{
- .start = AT91_BASE_SYS + AT91_RTT0,
- .end = AT91_BASE_SYS + AT91_RTT0 + SZ_16 - 1,
+ .start = AT91SAM9263_BASE_RTT0,
+ .end = AT91SAM9263_BASE_RTT0 + SZ_16 - 1,
.flags = IORESOURCE_MEM,
}
};
static struct resource rtt1_resources[] = {
{
- .start = AT91_BASE_SYS + AT91_RTT1,
- .end = AT91_BASE_SYS + AT91_RTT1 + SZ_16 - 1,
+ .start = AT91SAM9263_BASE_RTT1,
+ .end = AT91SAM9263_BASE_RTT1 + SZ_16 - 1,
.flags = IORESOURCE_MEM,
}
};
* -------------------------------------------------------------------- */
#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+ {
+ .start = AT91SAM9263_BASE_WDT,
+ .end = AT91SAM9263_BASE_WDT + SZ_16 - 1,
+ .flags = IORESOURCE_MEM,
+ }
+};
+
static struct platform_device at91sam9263_wdt_device = {
.name = "at91_wdt",
.id = -1,
- .num_resources = 0,
+ .resource = wdt_resources,
+ .num_resources = ARRAY_SIZE(wdt_resources),
};
static void __init at91_add_device_watchdog(void)
static struct resource dbgu_resources[] = {
[0] = {
- .start = AT91_BASE_SYS + AT91_DBGU,
- .end = AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+ .start = AT91SAM9263_BASE_DBGU,
+ .end = AT91SAM9263_BASE_DBGU + SZ_512 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
static u32 pit_cycle; /* write-once */
static u32 pit_cnt; /* access only w/system irq blocked */
+static void __iomem *pit_base_addr __read_mostly;
+static inline unsigned int pit_read(unsigned int reg_offset)
+{
+ return __raw_readl(pit_base_addr + reg_offset);
+}
+
+static inline void pit_write(unsigned int reg_offset, unsigned long value)
+{
+ __raw_writel(value, pit_base_addr + reg_offset);
+}
/*
* Clocksource: just a monotonic counter of MCK/16 cycles.
raw_local_irq_save(flags);
elapsed = pit_cnt;
- t = at91_sys_read(AT91_PIT_PIIR);
+ t = pit_read(AT91_PIT_PIIR);
raw_local_irq_restore(flags);
elapsed += PIT_PICNT(t) * pit_cycle;
switch (mode) {
case CLOCK_EVT_MODE_PERIODIC:
/* update clocksource counter */
- pit_cnt += pit_cycle * PIT_PICNT(at91_sys_read(AT91_PIT_PIVR));
- at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN
+ pit_cnt += pit_cycle * PIT_PICNT(pit_read(AT91_PIT_PIVR));
+ pit_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN
| AT91_PIT_PITIEN);
break;
case CLOCK_EVT_MODE_ONESHOT:
case CLOCK_EVT_MODE_SHUTDOWN:
case CLOCK_EVT_MODE_UNUSED:
/* disable irq, leaving the clocksource active */
- at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN);
+ pit_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN);
break;
case CLOCK_EVT_MODE_RESUME:
break;
/* The PIT interrupt may be disabled, and is shared */
if ((pit_clkevt.mode == CLOCK_EVT_MODE_PERIODIC)
- && (at91_sys_read(AT91_PIT_SR) & AT91_PIT_PITS)) {
+ && (pit_read(AT91_PIT_SR) & AT91_PIT_PITS)) {
unsigned nr_ticks;
/* Get number of ticks performed before irq, and ack it */
- nr_ticks = PIT_PICNT(at91_sys_read(AT91_PIT_PIVR));
+ nr_ticks = PIT_PICNT(pit_read(AT91_PIT_PIVR));
do {
pit_cnt += pit_cycle;
pit_clkevt.event_handler(&pit_clkevt);
static void at91sam926x_pit_reset(void)
{
/* Disable timer and irqs */
- at91_sys_write(AT91_PIT_MR, 0);
+ pit_write(AT91_PIT_MR, 0);
/* Clear any pending interrupts, wait for PIT to stop counting */
- while (PIT_CPIV(at91_sys_read(AT91_PIT_PIVR)) != 0)
+ while (PIT_CPIV(pit_read(AT91_PIT_PIVR)) != 0)
cpu_relax();
/* Start PIT but don't enable IRQ */
- at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN);
+ pit_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN);
}
/*
static void at91sam926x_pit_suspend(void)
{
/* Disable timer */
- at91_sys_write(AT91_PIT_MR, 0);
+ pit_write(AT91_PIT_MR, 0);
+}
+
+void __init at91sam926x_ioremap_pit(u32 addr)
+{
+ pit_base_addr = ioremap(addr, 16);
+
+ if (!pit_base_addr)
+ panic("Impossible to ioremap PIT\n");
}
struct sys_timer at91sam926x_timer = {
*/
#include <linux/module.h>
-#include <linux/pm.h>
#include <linux/dma-mapping.h>
#include <asm/irq.h>
#include <mach/at91sam9g45.h>
#include <mach/at91_pmc.h>
#include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
#include <mach/cpu.h>
#include "soc.h"
#include "generic.h"
#include "clock.h"
+#include "sam9_smc.h"
/* --------------------------------------------------------------------
* Clocks
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk macb_clk = {
- .name = "macb_clk",
+ .name = "pclk",
.pmc_mask = 1 << AT91SAM9G45_ID_EMAC,
.type = CLK_TYPE_PERIPHERAL,
};
};
static struct clk_lookup periph_clocks_lookups[] = {
+ /* One additional fake clock for macb_hclk */
+ CLKDEV_CON_ID("hclk", &macb_clk),
/* One additional fake clock for ohci */
CLKDEV_CON_ID("ohci_clk", &uhphs_clk),
CLKDEV_CON_DEV_ID("ehci_clk", "atmel-ehci", &uhphs_clk),
CLKDEV_CON_DEV_ID("usart", "fff98000.serial", &usart3_clk),
/* fake hclk clock */
CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &uhphs_clk),
+ CLKDEV_CON_ID("pioA", &pioA_clk),
+ CLKDEV_CON_ID("pioB", &pioB_clk),
+ CLKDEV_CON_ID("pioC", &pioC_clk),
+ CLKDEV_CON_ID("pioD", &pioDE_clk),
+ CLKDEV_CON_ID("pioE", &pioDE_clk),
};
static struct clk_lookup usart_clocks_lookups[] = {
* GPIO
* -------------------------------------------------------------------- */
-static struct at91_gpio_bank at91sam9g45_gpio[] = {
+static struct at91_gpio_bank at91sam9g45_gpio[] __initdata = {
{
.id = AT91SAM9G45_ID_PIOA,
- .offset = AT91_PIOA,
- .clock = &pioA_clk,
+ .regbase = AT91SAM9G45_BASE_PIOA,
}, {
.id = AT91SAM9G45_ID_PIOB,
- .offset = AT91_PIOB,
- .clock = &pioB_clk,
+ .regbase = AT91SAM9G45_BASE_PIOB,
}, {
.id = AT91SAM9G45_ID_PIOC,
- .offset = AT91_PIOC,
- .clock = &pioC_clk,
+ .regbase = AT91SAM9G45_BASE_PIOC,
}, {
.id = AT91SAM9G45_ID_PIODE,
- .offset = AT91_PIOD,
- .clock = &pioDE_clk,
+ .regbase = AT91SAM9G45_BASE_PIOD,
}, {
.id = AT91SAM9G45_ID_PIODE,
- .offset = AT91_PIOE,
- .clock = &pioDE_clk,
+ .regbase = AT91SAM9G45_BASE_PIOE,
}
};
at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
}
-static void at91sam9g45_poweroff(void)
-{
- at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
/* --------------------------------------------------------------------
* AT91SAM9G45 processor initialization
* -------------------------------------------------------------------- */
init_consistent_dma_size(SZ_4M);
}
+static void __init at91sam9g45_ioremap_registers(void)
+{
+ at91_ioremap_shdwc(AT91SAM9G45_BASE_SHDWC);
+ at91sam926x_ioremap_pit(AT91SAM9G45_BASE_PIT);
+ at91sam9_ioremap_smc(0, AT91SAM9G45_BASE_SMC);
+}
+
static void __init at91sam9g45_initialize(void)
{
arm_pm_restart = at91sam9g45_restart;
- pm_power_off = at91sam9g45_poweroff;
at91_extern_irq = (1 << AT91SAM9G45_ID_IRQ0);
/* Register GPIO subsystem */
struct at91_init_soc __initdata at91sam9g45_soc = {
.map_io = at91sam9g45_map_io,
.default_irq_priority = at91sam9g45_default_irq_priority,
+ .ioremap_registers = at91sam9g45_ioremap_registers,
.register_clocks = at91sam9g45_register_clocks,
.init = at91sam9g45_initialize,
};
static struct resource hdmac_resources[] = {
[0] = {
- .start = AT91_BASE_SYS + AT91_DMA,
- .end = AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+ .start = AT91SAM9G45_BASE_DMA,
+ .end = AT91SAM9G45_BASE_DMA + SZ_512 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
- if (data->vbus_pin[i])
+ if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i], 0);
}
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
- if (data->vbus_pin[i])
+ if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i], 0);
}
usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
- if (data && data->vbus_pin > 0) {
+ if (data && gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
usba_udc_data.pdata.vbus_pin = data->vbus_pin;
#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
static struct resource eth_resources[] = {
[0] = {
.num_resources = ARRAY_SIZE(eth_resources),
};
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
{
if (!data)
return;
- if (data->phy_irq_pin) {
+ if (gpio_is_valid(data->phy_irq_pin)) {
at91_set_gpio_input(data->phy_irq_pin, 0);
at91_set_deglitch(data->phy_irq_pin, 1);
}
platform_device_register(&at91sam9g45_eth_device);
}
#else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
#endif
/* input/irq */
- if (data->slot[0].detect_pin) {
+ if (gpio_is_valid(data->slot[0].detect_pin)) {
at91_set_gpio_input(data->slot[0].detect_pin, 1);
at91_set_deglitch(data->slot[0].detect_pin, 1);
}
- if (data->slot[0].wp_pin)
+ if (gpio_is_valid(data->slot[0].wp_pin))
at91_set_gpio_input(data->slot[0].wp_pin, 1);
if (mmc_id == 0) { /* MCI0 */
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91_BASE_SYS + AT91_ECC,
- .end = AT91_BASE_SYS + AT91_ECC + SZ_512 - 1,
+ .start = AT91SAM9G45_BASE_ECC,
+ .end = AT91SAM9G45_BASE_ECC + SZ_512 - 1,
.flags = IORESOURCE_MEM,
}
};
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
nand_data = *data;
at91_set_A_periph(AT91_PIN_PD6, 0); /* AC97RX */
/* reset */
- if (data->reset_pin)
+ if (gpio_is_valid(data->reset_pin))
at91_set_gpio_output(data->reset_pin, 0);
ac97_data = *data;
* -------------------------------------------------------------------- */
#if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE)
+static struct resource rtc_resources[] = {
+ [0] = {
+ .start = AT91SAM9G45_BASE_RTC,
+ .end = AT91SAM9G45_BASE_RTC + SZ_256 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91_ID_SYS,
+ .end = AT91_ID_SYS,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
static struct platform_device at91sam9g45_rtc_device = {
.name = "at91_rtc",
.id = -1,
- .num_resources = 0,
+ .resource = rtc_resources,
+ .num_resources = ARRAY_SIZE(rtc_resources),
};
static void __init at91_add_device_rtc(void)
static struct resource rtt_resources[] = {
{
- .start = AT91_BASE_SYS + AT91_RTT,
- .end = AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+ .start = AT91SAM9G45_BASE_RTT,
+ .end = AT91SAM9G45_BASE_RTT + SZ_16 - 1,
.flags = IORESOURCE_MEM,
}
};
* -------------------------------------------------------------------- */
#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+ {
+ .start = AT91SAM9G45_BASE_WDT,
+ .end = AT91SAM9G45_BASE_WDT + SZ_16 - 1,
+ .flags = IORESOURCE_MEM,
+ }
+};
+
static struct platform_device at91sam9g45_wdt_device = {
.name = "at91_wdt",
.id = -1,
- .num_resources = 0,
+ .resource = wdt_resources,
+ .num_resources = ARRAY_SIZE(wdt_resources),
};
static void __init at91_add_device_watchdog(void)
#if defined(CONFIG_SERIAL_ATMEL)
static struct resource dbgu_resources[] = {
[0] = {
- .start = AT91_BASE_SYS + AT91_DBGU,
- .end = AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+ .start = AT91SAM9G45_BASE_DBGU,
+ .end = AT91SAM9G45_BASE_DBGU + SZ_512 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
*/
#include <linux/module.h>
-#include <linux/pm.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <mach/at91sam9rl.h>
#include <mach/at91_pmc.h>
#include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
#include "soc.h"
#include "generic.h"
#include "clock.h"
+#include "sam9_smc.h"
/* --------------------------------------------------------------------
* Clocks
CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk),
CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
+ CLKDEV_CON_ID("pioA", &pioA_clk),
+ CLKDEV_CON_ID("pioB", &pioB_clk),
+ CLKDEV_CON_ID("pioC", &pioC_clk),
+ CLKDEV_CON_ID("pioD", &pioD_clk),
};
static struct clk_lookup usart_clocks_lookups[] = {
* GPIO
* -------------------------------------------------------------------- */
-static struct at91_gpio_bank at91sam9rl_gpio[] = {
+static struct at91_gpio_bank at91sam9rl_gpio[] __initdata = {
{
.id = AT91SAM9RL_ID_PIOA,
- .offset = AT91_PIOA,
- .clock = &pioA_clk,
+ .regbase = AT91SAM9RL_BASE_PIOA,
}, {
.id = AT91SAM9RL_ID_PIOB,
- .offset = AT91_PIOB,
- .clock = &pioB_clk,
+ .regbase = AT91SAM9RL_BASE_PIOB,
}, {
.id = AT91SAM9RL_ID_PIOC,
- .offset = AT91_PIOC,
- .clock = &pioC_clk,
+ .regbase = AT91SAM9RL_BASE_PIOC,
}, {
.id = AT91SAM9RL_ID_PIOD,
- .offset = AT91_PIOD,
- .clock = &pioD_clk,
+ .regbase = AT91SAM9RL_BASE_PIOD,
}
};
-static void at91sam9rl_poweroff(void)
-{
- at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
/* --------------------------------------------------------------------
* AT91SAM9RL processor initialization
* -------------------------------------------------------------------- */
at91_init_sram(0, AT91SAM9RL_SRAM_BASE, sram_size);
}
+static void __init at91sam9rl_ioremap_registers(void)
+{
+ at91_ioremap_shdwc(AT91SAM9RL_BASE_SHDWC);
+ at91sam926x_ioremap_pit(AT91SAM9RL_BASE_PIT);
+ at91sam9_ioremap_smc(0, AT91SAM9RL_BASE_SMC);
+}
+
static void __init at91sam9rl_initialize(void)
{
arm_pm_restart = at91sam9_alt_restart;
- pm_power_off = at91sam9rl_poweroff;
at91_extern_irq = (1 << AT91SAM9RL_ID_IRQ0);
/* Register GPIO subsystem */
struct at91_init_soc __initdata at91sam9rl_soc = {
.map_io = at91sam9rl_map_io,
.default_irq_priority = at91sam9rl_default_irq_priority,
+ .ioremap_registers = at91sam9rl_ioremap_registers,
.register_clocks = at91sam9rl_register_clocks,
.init = at91sam9rl_initialize,
};
static struct resource hdmac_resources[] = {
[0] = {
- .start = AT91_BASE_SYS + AT91_DMA,
- .end = AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+ .start = AT91SAM9RL_BASE_DMA,
+ .end = AT91SAM9RL_BASE_DMA + SZ_512 - 1,
.flags = IORESOURCE_MEM,
},
[2] = {
usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
- if (data && data->vbus_pin > 0) {
+ if (data && gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
usba_udc_data.pdata.vbus_pin = data->vbus_pin;
return;
/* input/irq */
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
- if (data->wp_pin)
+ if (gpio_is_valid(data->wp_pin))
at91_set_gpio_input(data->wp_pin, 1);
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
/* CLK */
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91_BASE_SYS + AT91_ECC,
- .end = AT91_BASE_SYS + AT91_ECC + SZ_512 - 1,
+ .start = AT91SAM9RL_BASE_ECC,
+ .end = AT91SAM9RL_BASE_ECC + SZ_512 - 1,
.flags = IORESOURCE_MEM,
}
};
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
at91_set_A_periph(AT91_PIN_PB4, 0); /* NANDOE */
at91_set_A_periph(AT91_PIN_PD4, 0); /* AC97RX */
/* reset */
- if (data->reset_pin)
+ if (gpio_is_valid(data->reset_pin))
at91_set_gpio_output(data->reset_pin, 0);
ac97_data = *data;
static struct resource rtt_resources[] = {
{
- .start = AT91_BASE_SYS + AT91_RTT,
- .end = AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+ .start = AT91SAM9RL_BASE_RTT,
+ .end = AT91SAM9RL_BASE_RTT + SZ_16 - 1,
.flags = IORESOURCE_MEM,
}
};
* -------------------------------------------------------------------- */
#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+ {
+ .start = AT91SAM9RL_BASE_WDT,
+ .end = AT91SAM9RL_BASE_WDT + SZ_16 - 1,
+ .flags = IORESOURCE_MEM,
+ }
+};
+
static struct platform_device at91sam9rl_wdt_device = {
.name = "at91_wdt",
.id = -1,
- .num_resources = 0,
+ .resource = wdt_resources,
+ .num_resources = ARRAY_SIZE(wdt_resources),
};
static void __init at91_add_device_watchdog(void)
#if defined(CONFIG_SERIAL_ATMEL)
static struct resource dbgu_resources[] = {
[0] = {
- .start = AT91_BASE_SYS + AT91_DBGU,
- .end = AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+ .start = AT91SAM9RL_BASE_DBGU,
+ .end = AT91SAM9RL_BASE_DBGU + SZ_512 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
at91_set_serial_console(0);
}
-static struct at91_eth_data __initdata onearm_eth_data = {
+static struct macb_platform_data __initdata onearm_eth_data = {
.phy_irq_pin = AT91_PIN_PC4,
.is_rmii = 1,
};
static struct at91_usbh_data __initdata onearm_usbh_data = {
.ports = 1,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata onearm_udc_data = {
*/
static struct at91_usbh_data __initdata afeb9260_usbh_data = {
.ports = 1,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
*/
static struct at91_udc_data __initdata afeb9260_udc_data = {
.vbus_pin = AT91_PIN_PC5,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata afeb9260_macb_data = {
+static struct macb_platform_data __initdata afeb9260_macb_data = {
.phy_irq_pin = AT91_PIN_PA9,
.is_rmii = 0,
};
.bus_width_16 = 0,
.parts = afeb9260_nand_partition,
.num_parts = ARRAY_SIZE(afeb9260_nand_partition),
+ .det_pin = -EINVAL,
};
.wp_pin = AT91_PIN_PC4,
.slot_b = 1,
.wire4 = 1,
+ .vcc_pin = -EINVAL,
};
static struct at91_cf_data afeb9260_cf_data = {
.chipselect = 4,
.irq_pin = AT91_PIN_PA6,
+ .det_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
.rst_pin = AT91_PIN_PA7,
.flags = AT91_CF_TRUE_IDE,
};
*/
static struct at91_usbh_data __initdata cam60_usbh_data = {
.ports = 1,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
* MACB Ethernet device
*/
-static struct __initdata at91_eth_data cam60_macb_data = {
+static struct __initdata macb_platform_data cam60_macb_data = {
.phy_irq_pin = AT91_PIN_PB5,
.is_rmii = 0,
};
static struct atmel_nand_data __initdata cam60_nand_data = {
.ale = 21,
.cle = 22,
- // .det_pin = ... not there
+ .det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PA9,
.enable_pin = AT91_PIN_PA7,
.parts = cam60_nand_partition,
static void __init cam60_add_device_nand(void)
{
/* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &cam60_nand_smc_config);
+ sam9_smc_configure(0, 3, &cam60_nand_smc_config);
at91_add_device_nand(&cam60_nand_data);
}
*/
static struct at91_usbh_data __initdata cap9adk_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
*/
static struct at91_mmc_data __initdata cap9adk_mmc_data = {
.wire4 = 1,
-// .det_pin = ... not connected
-// .wp_pin = ... not connected
-// .vcc_pin = ... not connected
+ .det_pin = -EINVAL,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata cap9adk_macb_data = {
+static struct macb_platform_data __initdata cap9adk_macb_data = {
+ .phy_irq_pin = -EINVAL,
.is_rmii = 1,
};
static struct atmel_nand_data __initdata cap9adk_nand_data = {
.ale = 21,
.cle = 22,
-// .det_pin = ... not connected
-// .rdy_pin = ... not connected
+ .det_pin = -EINVAL,
+ .rdy_pin = -EINVAL,
.enable_pin = AT91_PIN_PD15,
.parts = cap9adk_nand_partitions,
.num_parts = ARRAY_SIZE(cap9adk_nand_partitions),
cap9adk_nand_smc_config.mode |= AT91_SMC_DBW_8;
/* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &cap9adk_nand_smc_config);
+ sam9_smc_configure(0, 3, &cap9adk_nand_smc_config);
at91_add_device_nand(&cap9adk_nand_data);
}
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_VDDIOMSEL_3_3V);
/* configure chip-select 0 (NOR) */
- sam9_smc_configure(0, &cap9adk_nor_smc_config);
+ sam9_smc_configure(0, 0, &cap9adk_nor_smc_config);
platform_device_register(&cap9adk_nor_flash);
}
* AC97
*/
static struct ac97c_platform_data cap9adk_ac97_data = {
-// .reset_pin = ... not connected
+ .reset_pin = -EINVAL,
};
at91_set_serial_console(0);
}
-static struct at91_eth_data __initdata carmeva_eth_data = {
+static struct macb_platform_data __initdata carmeva_eth_data = {
.phy_irq_pin = AT91_PIN_PC4,
.is_rmii = 1,
};
static struct at91_usbh_data __initdata carmeva_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata carmeva_udc_data = {
// static struct at91_cf_data __initdata carmeva_cf_data = {
// .det_pin = AT91_PIN_PB0,
// .rst_pin = AT91_PIN_PC5,
- // .irq_pin = ... not connected
- // .vcc_pin = ... always powered
+ // .irq_pin = -EINVAL,
+ // .vcc_pin = -EINVAL,
// };
static struct at91_mmc_data __initdata carmeva_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PB10,
.wp_pin = AT91_PIN_PC14,
+ .vcc_pin = -EINVAL,
};
static struct spi_board_info carmeva_spi_devices[] = {
*/
static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
*/
static struct at91_udc_data __initdata cpu9krea_udc_data = {
.vbus_pin = AT91_PIN_PC8,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata cpu9krea_macb_data = {
+static struct macb_platform_data __initdata cpu9krea_macb_data = {
+ .phy_irq_pin = -EINVAL,
.is_rmii = 1,
};
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.bus_width_16 = 0,
+ .det_pin = -EINVAL,
};
#ifdef CONFIG_MACH_CPU9260
static void __init cpu9krea_add_device_nand(void)
{
- sam9_smc_configure(3, &cpu9krea_nand_smc_config);
+ sam9_smc_configure(0, 3, &cpu9krea_nand_smc_config);
at91_add_device_nand(&cpu9krea_nand_data);
}
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_VDDIOMSEL_3_3V);
/* configure chip-select 0 (NOR) */
- sam9_smc_configure(0, &cpu9krea_nor_smc_config);
+ sam9_smc_configure(0, 0, &cpu9krea_nor_smc_config);
platform_device_register(&cpu9krea_nor_flash);
}
.slot_b = 0,
.wire4 = 1,
.det_pin = AT91_PIN_PA29,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
static void __init cpu9krea_board_init(void)
at91_set_serial_console(0);
}
-static struct at91_eth_data __initdata cpuat91_eth_data = {
+static struct macb_platform_data __initdata cpuat91_eth_data = {
+ .phy_irq_pin = -EINVAL,
.is_rmii = 1,
};
static struct at91_usbh_data __initdata cpuat91_usbh_data = {
.ports = 1,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata cpuat91_udc_data = {
static struct at91_mmc_data __initdata cpuat91_mmc_data = {
.det_pin = AT91_PIN_PC2,
.wire4 = 1,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
static struct physmap_flash_data cpuat91_flash_data = {
at91_set_serial_console(0);
}
-static struct at91_eth_data __initdata csb337_eth_data = {
+static struct macb_platform_data __initdata csb337_eth_data = {
.phy_irq_pin = AT91_PIN_PC2,
.is_rmii = 0,
};
static struct at91_usbh_data __initdata csb337_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata csb337_udc_data = {
- // this has no VBUS sensing pin
.pullup_pin = AT91_PIN_PA24,
+ .vbus_pin = -EINVAL,
};
static struct i2c_board_info __initdata csb337_i2c_devices[] = {
.slot_b = 0,
.wire4 = 1,
.wp_pin = AT91_PIN_PD6,
+ .vcc_pin = -EINVAL,
};
static struct spi_board_info csb337_spi_devices[] = {
at91_set_serial_console(0);
}
-static struct at91_eth_data __initdata csb637_eth_data = {
+static struct macb_platform_data __initdata csb637_eth_data = {
.phy_irq_pin = AT91_PIN_PC0,
.is_rmii = 0,
};
static struct at91_usbh_data __initdata csb637_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata csb637_udc_data = {
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
+ .det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC8,
.enable_pin = AT91_PIN_PC14,
};
ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
/* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &ek_nand_smc_config);
+ sam9_smc_configure(0, 3, &ek_nand_smc_config);
at91_add_device_nand(&ek_nand_data);
}
at91_set_serial_console(0);
}
-static struct at91_eth_data __initdata eb9200_eth_data = {
+static struct macb_platform_data __initdata eb9200_eth_data = {
.phy_irq_pin = AT91_PIN_PC4,
.is_rmii = 1,
};
static struct at91_usbh_data __initdata eb9200_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata eb9200_udc_data = {
};
static struct at91_cf_data __initdata eb9200_cf_data = {
+ .irq_pin = -EINVAL,
.det_pin = AT91_PIN_PB0,
+ .vcc_pin = -EINVAL,
.rst_pin = AT91_PIN_PC5,
- // .irq_pin = ... not connected
- // .vcc_pin = ... always powered
};
static struct at91_mmc_data __initdata eb9200_mmc_data = {
.slot_b = 0,
.wire4 = 1,
+ .det_pin = -EINVAL,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
static struct i2c_board_info __initdata eb9200_i2c_devices[] = {
at91_set_serial_console(0);
}
-static struct at91_eth_data __initdata ecb_at91eth_data = {
+static struct macb_platform_data __initdata ecb_at91eth_data = {
.phy_irq_pin = AT91_PIN_PC4,
.is_rmii = 0,
};
static struct at91_usbh_data __initdata ecb_at91usbh_data = {
.ports = 1,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_mmc_data __initdata ecb_at91mmc_data = {
.slot_b = 0,
.wire4 = 1,
+ .det_pin = -EINVAL,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
at91_set_serial_console(0);
}
-static struct at91_eth_data __initdata eco920_eth_data = {
+static struct macb_platform_data __initdata eco920_eth_data = {
.phy_irq_pin = AT91_PIN_PC2,
.is_rmii = 1,
};
static struct at91_usbh_data __initdata eco920_usbh_data = {
.ports = 1,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata eco920_udc_data = {
static struct at91_mmc_data __initdata eco920_mmc_data = {
.slot_b = 0,
.wire4 = 0,
+ .det_pin = -EINVAL,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
static struct physmap_flash_data eco920_flash_data = {
/* USB Host port */
static struct at91_usbh_data __initdata flexibity_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/* USB Device port */
static struct at91_udc_data __initdata flexibity_udc_data = {
.vbus_pin = AT91_PIN_PC5,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/* SPI devices */
.wire4 = 1,
.det_pin = AT91_PIN_PC9,
.wp_pin = AT91_PIN_PC4,
+ .vcc_pin = -EINVAL,
};
/* LEDs */
*/
static struct at91_usbh_data __initdata foxg20_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
*/
static struct at91_udc_data __initdata foxg20_udc_data = {
.vbus_pin = AT91_PIN_PC6,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata foxg20_macb_data = {
+static struct macb_platform_data __initdata foxg20_macb_data = {
.phy_irq_pin = AT91_PIN_PA7,
.is_rmii = 1,
};
static struct at91_mmc_data __initdata foxg20_mmc_data = {
.slot_b = 1,
.wire4 = 1,
+ .det_pin = -EINVAL,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
*/
static struct at91_usbh_data __initdata usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
*/
static struct at91_udc_data __initdata udc_data = {
.vbus_pin = AT91_PIN_PA22,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata macb_data = {
+static struct macb_platform_data __initdata macb_data = {
.phy_irq_pin = AT91_PIN_PA28,
.is_rmii = 1,
};
static struct at91_cf_data __initdata gsia18s_cf1_data = {
.irq_pin = AT91_PIN_PA27,
.det_pin = AT91_PIN_PB30,
+ .vcc_pin = -EINVAL,
.rst_pin = AT91_PIN_PB31,
.chipselect = 5,
.flags = AT91_CF_TRUE_IDE,
at91_set_serial_console(0);
}
-static struct at91_eth_data __initdata kafa_eth_data = {
+static struct macb_platform_data __initdata kafa_eth_data = {
.phy_irq_pin = AT91_PIN_PC4,
.is_rmii = 0,
};
static struct at91_usbh_data __initdata kafa_usbh_data = {
.ports = 1,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata kafa_udc_data = {
at91_set_serial_console(0);
}
-static struct at91_eth_data __initdata kb9202_eth_data = {
+static struct macb_platform_data __initdata kb9202_eth_data = {
.phy_irq_pin = AT91_PIN_PB29,
.is_rmii = 0,
};
static struct at91_usbh_data __initdata kb9202_usbh_data = {
.ports = 1,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata kb9202_udc_data = {
.det_pin = AT91_PIN_PB2,
.slot_b = 0,
.wire4 = 1,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
static struct mtd_partition __initdata kb9202_nand_partition[] = {
static struct atmel_nand_data __initdata kb9202_nand_data = {
.ale = 22,
.cle = 21,
- // .det_pin = ... not there
+ .det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC29,
.enable_pin = AT91_PIN_PC28,
.parts = kb9202_nand_partition,
static struct at91_usbh_data __initdata neocore926_usbh_data = {
.ports = 2,
.vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 },
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
*/
static struct at91_udc_data __initdata neocore926_udc_data = {
.vbus_pin = AT91_PIN_PA25,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
.wire4 = 1,
.det_pin = AT91_PIN_PE18,
.wp_pin = AT91_PIN_PE19,
+ .vcc_pin = -EINVAL,
};
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata neocore926_macb_data = {
+static struct macb_platform_data __initdata neocore926_macb_data = {
.phy_irq_pin = AT91_PIN_PE31,
.is_rmii = 1,
};
.enable_pin = AT91_PIN_PD15,
.parts = neocore926_nand_partition,
.num_parts = ARRAY_SIZE(neocore926_nand_partition),
+ .det_pin = -EINVAL,
};
static struct sam9_smc_config __initdata neocore926_nand_smc_config = {
static void __init neocore926_add_device_nand(void)
{
/* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &neocore926_nand_smc_config);
+ sam9_smc_configure(0, 3, &neocore926_nand_smc_config);
at91_add_device_nand(&neocore926_nand_data);
}
static void __init add_device_pcontrol(void)
{
/* configure chip-select 4 (IO compatible to 8051 X4 ) */
- sam9_smc_configure(4, &pcontrol_smc_config[0]);
+ sam9_smc_configure(0, 4, &pcontrol_smc_config[0]);
/* configure chip-select 7 (FerroRAM 256KiBx16bit MR2A16A D4 ) */
- sam9_smc_configure(7, &pcontrol_smc_config[1]);
+ sam9_smc_configure(0, 7, &pcontrol_smc_config[1]);
}
*/
static struct at91_usbh_data __initdata usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata macb_data = {
+static struct macb_platform_data __initdata macb_data = {
.phy_irq_pin = AT91_PIN_PA28,
.is_rmii = 1,
};
at91_set_serial_console(0);
}
-static struct at91_eth_data __initdata picotux200_eth_data = {
+static struct macb_platform_data __initdata picotux200_eth_data = {
.phy_irq_pin = AT91_PIN_PC4,
.is_rmii = 1,
};
static struct at91_usbh_data __initdata picotux200_usbh_data = {
.ports = 1,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_mmc_data __initdata picotux200_mmc_data = {
.slot_b = 0,
.wire4 = 1,
.wp_pin = AT91_PIN_PA17,
+ .vcc_pin = -EINVAL,
};
#define PICOTUX200_FLASH_BASE AT91_CHIPSELECT_0
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PC5,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/*
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
.phy_irq_pin = AT91_PIN_PA31,
.is_rmii = 1,
};
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
-// .det_pin = ... not connected
+ .det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.parts = ek_nand_partition,
static void __init ek_add_device_nand(void)
{
/* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &ek_nand_smc_config);
+ sam9_smc_configure(0, 3, &ek_nand_smc_config);
at91_add_device_nand(&ek_nand_data);
}
static struct at91_mmc_data __initdata ek_mmc_data = {
.slot_b = 0,
.wire4 = 1,
-// .det_pin = ... not connected
-// .wp_pin = ... not connected
-// .vcc_pin = ... not connected
+ .det_pin = -EINVAL,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
/*
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
/* shutdown controller, wakeup button (5 msec low) */
- at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
+ at91_shdwc_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
| AT91_SHDW_RTTWKEN);
}
at91_set_serial_console(0);
}
-static struct at91_eth_data __initdata dk_eth_data = {
+static struct macb_platform_data __initdata dk_eth_data = {
.phy_irq_pin = AT91_PIN_PC4,
.is_rmii = 1,
};
static struct at91_usbh_data __initdata dk_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata dk_udc_data = {
};
static struct at91_cf_data __initdata dk_cf_data = {
+ .irq_pin = -EINVAL,
.det_pin = AT91_PIN_PB0,
+ .vcc_pin = -EINVAL,
.rst_pin = AT91_PIN_PC5,
- // .irq_pin = ... not connected
- // .vcc_pin = ... always powered
};
#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
static struct at91_mmc_data __initdata dk_mmc_data = {
.slot_b = 0,
.wire4 = 1,
+ .det_pin = -EINVAL,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
#endif
.cle = 21,
.det_pin = AT91_PIN_PB1,
.rdy_pin = AT91_PIN_PC2,
- // .enable_pin = ... not there
+ .enable_pin = -EINVAL,
.parts = dk_nand_partition,
.num_parts = ARRAY_SIZE(dk_nand_partition),
};
at91_set_serial_console(0);
}
-static struct at91_eth_data __initdata ek_eth_data = {
+static struct macb_platform_data __initdata ek_eth_data = {
.phy_irq_pin = AT91_PIN_PC4,
.is_rmii = 1,
};
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata ek_udc_data = {
.slot_b = 0,
.wire4 = 1,
.wp_pin = AT91_PIN_PA17,
+ .vcc_pin = -EINVAL,
};
#endif
/*
* Ethernet
*/
-static struct at91_eth_data rsi_ews_eth_data __initdata = {
+static struct macb_platform_data rsi_ews_eth_data __initdata = {
.phy_irq_pin = AT91_PIN_PC4,
.is_rmii = 1,
};
*/
static struct at91_usbh_data rsi_ews_usbh_data __initdata = {
.ports = 1,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PC5,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
.phy_irq_pin = AT91_PIN_PA7,
.is_rmii = 0,
};
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
-// .det_pin = ... not connected
+ .det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.parts = ek_nand_partition,
static void __init ek_add_device_nand(void)
{
/* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &ek_nand_smc_config);
+ sam9_smc_configure(0, 3, &ek_nand_smc_config);
at91_add_device_nand(&ek_nand_data);
}
.wire4 = 1,
.det_pin = AT91_PIN_PC8,
.wp_pin = AT91_PIN_PC4,
-// .vcc_pin = ... not connected
+ .vcc_pin = -EINVAL,
};
static void __init ek_board_init(void)
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PC5,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
.phy_irq_pin = AT91_PIN_PA7,
.is_rmii = 1,
};
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
-// .det_pin = ... not connected
+ .det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.parts = ek_nand_partition,
ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
/* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &ek_nand_smc_config);
+ sam9_smc_configure(0, 3, &ek_nand_smc_config);
at91_add_device_nand(&ek_nand_data);
}
static struct at91_mmc_data __initdata ek_mmc_data = {
.slot_b = 1,
.wire4 = 1,
-// .det_pin = ... not connected
-// .wp_pin = ... not connected
-// .vcc_pin = ... not connected
+ .det_pin = -EINVAL,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
static void __init ek_add_device_dm9000(void)
{
/* Configure chip-select 2 (DM9000) */
- sam9_smc_configure(2, &dm9000_smc_config);
+ sam9_smc_configure(0, 2, &dm9000_smc_config);
/* Configure Reset signal as output */
at91_set_gpio_output(AT91_PIN_PC10, 0);
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PB29,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 22,
.cle = 21,
-// .det_pin = ... not connected
+ .det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC15,
.enable_pin = AT91_PIN_PC14,
.parts = ek_nand_partition,
ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
/* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &ek_nand_smc_config);
+ sam9_smc_configure(0, 3, &ek_nand_smc_config);
at91_add_device_nand(&ek_nand_data);
}
*/
static struct at91_mmc_data __initdata ek_mmc_data = {
.wire4 = 1,
+ .det_pin = -EINVAL,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
#endif /* CONFIG_SPI_ATMEL_* */
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
.vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 },
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PA25,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
.wire4 = 1,
.det_pin = AT91_PIN_PE18,
.wp_pin = AT91_PIN_PE19,
-// .vcc_pin = ... not connected
+ .vcc_pin = -EINVAL,
};
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
.phy_irq_pin = AT91_PIN_PE31,
.is_rmii = 1,
};
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
-// .det_pin = ... not connected
+ .det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PA22,
.enable_pin = AT91_PIN_PD15,
.parts = ek_nand_partition,
ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
/* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &ek_nand_smc_config);
+ sam9_smc_configure(0, 3, &ek_nand_smc_config);
at91_add_device_nand(&ek_nand_data);
}
* reset_pin is not connected: NRST
*/
static struct ac97c_platform_data ek_ac97_data = {
+ .reset_pin = -EINVAL,
};
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PC5,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
.phy_irq_pin = AT91_PIN_PA7,
.is_rmii = 1,
};
.cle = 22,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
+ .det_pin = -EINVAL,
.parts = ek_nand_partition,
.num_parts = ARRAY_SIZE(ek_nand_partition),
};
ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
/* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &ek_nand_smc_config);
+ sam9_smc_configure(0, 3, &ek_nand_smc_config);
at91_add_device_nand(&ek_nand_data);
}
.slot[1] = {
.bus_width = 4,
.detect_pin = AT91_PIN_PC9,
+ .wp_pin = -EINVAL,
},
};
.slot_b = 1, /* Only one slot so use slot B */
.wire4 = 1,
.det_pin = AT91_PIN_PC9,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
#endif
if (ek_have_2mmc()) {
ek_mmc_data.slot[0].bus_width = 4;
ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2;
+ ek_mmc_data.slot[0].wp_pin = -1;
}
at91_add_device_mci(0, &ek_mmc_data);
#else
static struct at91_usbh_data __initdata ek_usbh_hs_data = {
.ports = 2,
.vbus_pin = {AT91_PIN_PD1, AT91_PIN_PD3},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
.slot[0] = {
.bus_width = 4,
.detect_pin = AT91_PIN_PD10,
+ .wp_pin = -EINVAL,
},
};
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
.phy_irq_pin = AT91_PIN_PD5,
.is_rmii = 1,
};
.cle = 22,
.rdy_pin = AT91_PIN_PC8,
.enable_pin = AT91_PIN_PC14,
+ .det_pin = -EINVAL,
.parts = ek_nand_partition,
.num_parts = ARRAY_SIZE(ek_nand_partition),
};
ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
/* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &ek_nand_smc_config);
+ sam9_smc_configure(0, 3, &ek_nand_smc_config);
at91_add_device_nand(&ek_nand_data);
}
* reset_pin is not connected: NRST
*/
static struct ac97c_platform_data ek_ac97_data = {
+ .reset_pin = -EINVAL,
};
static struct at91_mmc_data __initdata ek_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PA15,
-// .wp_pin = ... not connected
-// .vcc_pin = ... not connected
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
-// .det_pin = ... not connected
+ .det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PD17,
.enable_pin = AT91_PIN_PB6,
.parts = ek_nand_partition,
static void __init ek_add_device_nand(void)
{
/* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &ek_nand_smc_config);
+ sam9_smc_configure(0, 3, &ek_nand_smc_config);
at91_add_device_nand(&ek_nand_data);
}
* reset_pin is not connected: NRST
*/
static struct ac97c_platform_data ek_ac97_data = {
+ .reset_pin = -EINVAL,
};
static struct at91_usbh_data __initdata snapper9260_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata snapper9260_udc_data = {
.vbus_pin = SNAPPER9260_IO_EXP_GPIO(5),
.vbus_active_low = 1,
.vbus_polled = 1,
+ .pullup_pin = -EINVAL,
};
-static struct at91_eth_data snapper9260_macb_data = {
+static struct macb_platform_data snapper9260_macb_data = {
+ .phy_irq_pin = -EINVAL,
.is_rmii = 1,
};
.parts = snapper9260_nand_partitions,
.num_parts = ARRAY_SIZE(snapper9260_nand_partitions),
.bus_width_16 = 0,
+ .enable_pin = -EINVAL,
+ .det_pin = -EINVAL,
};
static struct sam9_smc_config __initdata snapper9260_nand_smc_config = {
static void __init snapper9260_add_device_nand(void)
{
at91_set_A_periph(AT91_PIN_PC14, 0);
- sam9_smc_configure(3, &snapper9260_nand_smc_config);
+ sam9_smc_configure(0, 3, &snapper9260_nand_smc_config);
at91_add_device_nand(&snapper9260_nand_data);
}
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.bus_width_16 = 0,
+ .det_pin = -EINVAL,
};
static struct sam9_smc_config __initdata nand_smc_config = {
static void __init add_device_nand(void)
{
/* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &nand_smc_config);
+ sam9_smc_configure(0, 3, &nand_smc_config);
at91_add_device_nand(&nand_data);
}
static struct mci_platform_data __initdata mmc_data = {
.slot[0] = {
.bus_width = 4,
+ .detect_pin = -1,
+ .wp_pin = -1,
},
};
#else
static struct at91_mmc_data __initdata mmc_data = {
.slot_b = 0,
.wire4 = 1,
+ .det_pin = -EINVAL,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
#endif
*/
static struct at91_usbh_data __initdata usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
*/
static struct at91_udc_data __initdata portuxg20_udc_data = {
.vbus_pin = AT91_PIN_PC7,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
static struct at91_udc_data __initdata stamp9g20evb_udc_data = {
.vbus_pin = AT91_PIN_PA22,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata macb_data = {
+static struct macb_platform_data __initdata macb_data = {
.phy_irq_pin = AT91_PIN_PA28,
.is_rmii = 1,
};
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PB11,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
static void __init ek_add_device_udc(void)
/*
* MACB Ethernet device
*/
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
.phy_irq_pin = AT91_PIN_PE31,
.is_rmii = 1,
};
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
-// .det_pin = ... not connected
+ .det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PA22,
.enable_pin = AT91_PIN_PD15,
.parts = ek_nand_partition,
/* configure chip-select 3 (NAND) */
if (machine_is_usb_a9g20())
- sam9_smc_configure(3, &usb_a9g20_nand_smc_config);
+ sam9_smc_configure(0, 3, &usb_a9g20_nand_smc_config);
else
- sam9_smc_configure(3, &usb_a9260_nand_smc_config);
+ sam9_smc_configure(0, 3, &usb_a9260_nand_smc_config);
at91_add_device_nand(&ek_nand_data);
}
/* I2C */
at91_add_device_i2c(NULL, 0);
/* shutdown controller, wakeup button (5 msec low) */
- at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10)
+ at91_shdwc_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10)
| AT91_SHDW_WKMODE0_LOW
| AT91_SHDW_RTTWKEN);
}
/*
* Ethernet
*/
-static struct at91_eth_data __initdata yl9200_eth_data = {
+static struct macb_platform_data __initdata yl9200_eth_data = {
.phy_irq_pin = AT91_PIN_PB28,
.is_rmii = 1,
};
*/
static struct at91_usbh_data __initdata yl9200_usbh_data = {
.ports = 1, /* PQFP version of AT91RM9200 */
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
*/
static struct at91_mmc_data __initdata yl9200_mmc_data = {
.det_pin = AT91_PIN_PB9,
- // .wp_pin = ... not connected
.wire4 = 1,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
};
/*
static struct atmel_nand_data __initdata yl9200_nand_data = {
.ale = 6,
.cle = 7,
- // .det_pin = ... not connected
+ .det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC14, /* R/!B (Sheet10) */
.enable_pin = AT91_PIN_PC15, /* !CE (Sheet10) */
.parts = yl9200_nand_partition,
/* Timer */
struct sys_timer;
extern struct sys_timer at91rm9200_timer;
+extern void at91sam926x_ioremap_pit(u32 addr);
extern struct sys_timer at91sam926x_timer;
extern struct sys_timer at91x40_timer;
/* reset */
extern void at91sam9_alt_restart(char, const char *);
+/* shutdown */
+extern void at91_ioremap_shdwc(u32 base_addr);
+
/* GPIO */
#define AT91RM9200_PQFP 3 /* AT91RM9200 PQFP package has 3 banks */
#define AT91RM9200_BGA 4 /* AT91RM9200 BGA package has 4 banks */
struct at91_gpio_bank {
unsigned short id; /* peripheral ID */
- unsigned long offset; /* offset from system peripheral base */
- struct clk *clock; /* associated clock */
+ unsigned long regbase; /* offset from system peripheral base */
};
extern void __init at91_gpio_init(struct at91_gpio_bank *, int nr_banks);
extern void __init at91_gpio_irq_setup(void);
struct at91_gpio_chip {
struct gpio_chip chip;
struct at91_gpio_chip *next; /* Bank sharing same clock */
- struct at91_gpio_bank *bank; /* Bank definition */
+ int id; /* ID of register bank */
void __iomem *regbase; /* Base of register bank */
+ struct clk *clock; /* associated clock */
};
#define to_at91_gpio_chip(c) container_of(c, struct at91_gpio_chip, chip)
}
static struct at91_gpio_chip gpio_chip[] = {
- AT91_GPIO_CHIP("A", 0x00 + PIN_BASE, 32),
- AT91_GPIO_CHIP("B", 0x20 + PIN_BASE, 32),
- AT91_GPIO_CHIP("C", 0x40 + PIN_BASE, 32),
- AT91_GPIO_CHIP("D", 0x60 + PIN_BASE, 32),
- AT91_GPIO_CHIP("E", 0x80 + PIN_BASE, 32),
+ AT91_GPIO_CHIP("pioA", 0x00, 32),
+ AT91_GPIO_CHIP("pioB", 0x20, 32),
+ AT91_GPIO_CHIP("pioC", 0x40, 32),
+ AT91_GPIO_CHIP("pioD", 0x60, 32),
+ AT91_GPIO_CHIP("pioE", 0x80, 32),
};
static int gpio_banks;
static inline void __iomem *pin_to_controller(unsigned pin)
{
- pin -= PIN_BASE;
pin /= 32;
if (likely(pin < gpio_banks))
return gpio_chip[pin].regbase;
static inline unsigned pin_to_mask(unsigned pin)
{
- pin -= PIN_BASE;
return 1 << (pin % 32);
}
static int gpio_irq_set_wake(struct irq_data *d, unsigned state)
{
- unsigned mask = pin_to_mask(d->irq);
- unsigned bank = (d->irq - PIN_BASE) / 32;
+ unsigned pin = irq_to_gpio(d->irq);
+ unsigned mask = pin_to_mask(pin);
+ unsigned bank = pin / 32;
if (unlikely(bank >= MAX_GPIO_BANKS))
return -EINVAL;
else
wakeups[bank] &= ~mask;
- irq_set_irq_wake(gpio_chip[bank].bank->id, state);
+ irq_set_irq_wake(gpio_chip[bank].id, state);
return 0;
}
__raw_writel(wakeups[i], pio + PIO_IER);
if (!wakeups[i])
- clk_disable(gpio_chip[i].bank->clock);
+ clk_disable(gpio_chip[i].clock);
else {
#ifdef CONFIG_PM_DEBUG
printk(KERN_DEBUG "GPIO-%c may wake for %08x\n", 'A'+i, wakeups[i]);
void __iomem *pio = gpio_chip[i].regbase;
if (!wakeups[i])
- clk_enable(gpio_chip[i].bank->clock);
+ clk_enable(gpio_chip[i].clock);
__raw_writel(wakeups[i], pio + PIO_IDR);
__raw_writel(backups[i], pio + PIO_IER);
static void gpio_irq_mask(struct irq_data *d)
{
- void __iomem *pio = pin_to_controller(d->irq);
- unsigned mask = pin_to_mask(d->irq);
+ unsigned pin = irq_to_gpio(d->irq);
+ void __iomem *pio = pin_to_controller(pin);
+ unsigned mask = pin_to_mask(pin);
if (pio)
__raw_writel(mask, pio + PIO_IDR);
static void gpio_irq_unmask(struct irq_data *d)
{
- void __iomem *pio = pin_to_controller(d->irq);
- unsigned mask = pin_to_mask(d->irq);
+ unsigned pin = irq_to_gpio(d->irq);
+ void __iomem *pio = pin_to_controller(pin);
+ unsigned mask = pin_to_mask(pin);
if (pio)
__raw_writel(mask, pio + PIO_IER);
static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
{
- unsigned pin;
+ unsigned irq_pin;
struct irq_data *idata = irq_desc_get_irq_data(desc);
struct irq_chip *chip = irq_data_get_irq_chip(idata);
struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(idata);
continue;
}
- pin = at91_gpio->chip.base;
+ irq_pin = gpio_to_irq(at91_gpio->chip.base);
while (isr) {
if (isr & 1)
- generic_handle_irq(pin);
- pin++;
+ generic_handle_irq(irq_pin);
+ irq_pin++;
isr >>= 1;
}
}
seq_printf(s, "%i:\t", j);
for (bank = 0; bank < gpio_banks; bank++) {
- unsigned pin = PIN_BASE + (32 * bank) + j;
+ unsigned pin = (32 * bank) + j;
void __iomem *pio = pin_to_controller(pin);
unsigned mask = pin_to_mask(pin);
*/
void __init at91_gpio_irq_setup(void)
{
- unsigned pioc, pin;
+ unsigned pioc, irq = gpio_to_irq(0);
struct at91_gpio_chip *this, *prev;
- for (pioc = 0, pin = PIN_BASE, this = gpio_chip, prev = NULL;
+ for (pioc = 0, this = gpio_chip, prev = NULL;
pioc++ < gpio_banks;
prev = this, this++) {
- unsigned id = this->bank->id;
+ unsigned id = this->id;
unsigned i;
__raw_writel(~0, this->regbase + PIO_IDR);
- for (i = 0, pin = this->chip.base; i < 32; i++, pin++) {
- irq_set_lockdep_class(pin, &gpio_lock_class);
+ for (i = 0, irq = gpio_to_irq(this->chip.base); i < 32;
+ i++, irq++) {
+ irq_set_lockdep_class(irq, &gpio_lock_class);
/*
* Can use the "simple" and not "edge" handler since it's
* shorter, and the AIC handles interrupts sanely.
*/
- irq_set_chip_and_handler(pin, &gpio_irqchip,
+ irq_set_chip_and_handler(irq, &gpio_irqchip,
handle_simple_irq);
- set_irq_flags(pin, IRQF_VALID);
+ set_irq_flags(irq, IRQF_VALID);
}
/* The toplevel handler handles one bank of GPIOs, except
irq_set_chip_data(id, this);
irq_set_chained_handler(id, gpio_irq_handler);
}
- pr_info("AT91: %d gpio irqs in %d banks\n", pin - PIN_BASE, gpio_banks);
+ pr_info("AT91: %d gpio irqs in %d banks\n", irq - gpio_to_irq(0), gpio_banks);
}
/* gpiolib support */
for (i = 0; i < nr_banks; i++) {
at91_gpio = &gpio_chip[i];
- at91_gpio->bank = &data[i];
- at91_gpio->chip.base = PIN_BASE + i * 32;
- at91_gpio->regbase = at91_gpio->bank->offset +
- (void __iomem *)AT91_VA_BASE_SYS;
+ at91_gpio->id = data[i].id;
+ at91_gpio->chip.base = i * 32;
+
+ at91_gpio->regbase = ioremap(data[i].regbase, 512);
+ if (!at91_gpio->regbase) {
+ pr_err("at91_gpio.%d, failed to map registers, ignoring.\n", i);
+ continue;
+ }
+
+ at91_gpio->clock = clk_get_sys(NULL, at91_gpio->chip.label);
+ if (!at91_gpio->clock) {
+ pr_err("at91_gpio.%d, failed to get clock, ignoring.\n", i);
+ continue;
+ }
/* enable PIO controller's clock */
- clk_enable(at91_gpio->bank->clock);
+ clk_enable(at91_gpio->clock);
/* AT91SAM9263_ID_PIOCDE groups PIOC, PIOD, PIOE */
- if (last && last->bank->id == at91_gpio->bank->id)
+ if (last && last->id == at91_gpio->id)
last->next = at91_gpio;
last = at91_gpio;
#ifndef AT91_AIC_H
#define AT91_AIC_H
-#define AT91_AIC_SMR(n) (AT91_AIC + ((n) * 4)) /* Source Mode Registers 0-31 */
+#ifndef __ASSEMBLY__
+extern void __iomem *at91_aic_base;
+
+#define at91_aic_read(field) \
+ __raw_readl(at91_aic_base + field)
+
+#define at91_aic_write(field, value) \
+ __raw_writel(value, at91_aic_base + field);
+#else
+.extern at91_aic_base
+#endif
+
+#define AT91_AIC_SMR(n) ((n) * 4) /* Source Mode Registers 0-31 */
#define AT91_AIC_PRIOR (7 << 0) /* Priority Level */
#define AT91_AIC_SRCTYPE (3 << 5) /* Interrupt Source Type */
#define AT91_AIC_SRCTYPE_LOW (0 << 5)
#define AT91_AIC_SRCTYPE_HIGH (2 << 5)
#define AT91_AIC_SRCTYPE_RISING (3 << 5)
-#define AT91_AIC_SVR(n) (AT91_AIC + 0x80 + ((n) * 4)) /* Source Vector Registers 0-31 */
-#define AT91_AIC_IVR (AT91_AIC + 0x100) /* Interrupt Vector Register */
-#define AT91_AIC_FVR (AT91_AIC + 0x104) /* Fast Interrupt Vector Register */
-#define AT91_AIC_ISR (AT91_AIC + 0x108) /* Interrupt Status Register */
+#define AT91_AIC_SVR(n) (0x80 + ((n) * 4)) /* Source Vector Registers 0-31 */
+#define AT91_AIC_IVR 0x100 /* Interrupt Vector Register */
+#define AT91_AIC_FVR 0x104 /* Fast Interrupt Vector Register */
+#define AT91_AIC_ISR 0x108 /* Interrupt Status Register */
#define AT91_AIC_IRQID (0x1f << 0) /* Current Interrupt Identifier */
-#define AT91_AIC_IPR (AT91_AIC + 0x10c) /* Interrupt Pending Register */
-#define AT91_AIC_IMR (AT91_AIC + 0x110) /* Interrupt Mask Register */
-#define AT91_AIC_CISR (AT91_AIC + 0x114) /* Core Interrupt Status Register */
+#define AT91_AIC_IPR 0x10c /* Interrupt Pending Register */
+#define AT91_AIC_IMR 0x110 /* Interrupt Mask Register */
+#define AT91_AIC_CISR 0x114 /* Core Interrupt Status Register */
#define AT91_AIC_NFIQ (1 << 0) /* nFIQ Status */
#define AT91_AIC_NIRQ (1 << 1) /* nIRQ Status */
-#define AT91_AIC_IECR (AT91_AIC + 0x120) /* Interrupt Enable Command Register */
-#define AT91_AIC_IDCR (AT91_AIC + 0x124) /* Interrupt Disable Command Register */
-#define AT91_AIC_ICCR (AT91_AIC + 0x128) /* Interrupt Clear Command Register */
-#define AT91_AIC_ISCR (AT91_AIC + 0x12c) /* Interrupt Set Command Register */
-#define AT91_AIC_EOICR (AT91_AIC + 0x130) /* End of Interrupt Command Register */
-#define AT91_AIC_SPU (AT91_AIC + 0x134) /* Spurious Interrupt Vector Register */
-#define AT91_AIC_DCR (AT91_AIC + 0x138) /* Debug Control Register */
+#define AT91_AIC_IECR 0x120 /* Interrupt Enable Command Register */
+#define AT91_AIC_IDCR 0x124 /* Interrupt Disable Command Register */
+#define AT91_AIC_ICCR 0x128 /* Interrupt Clear Command Register */
+#define AT91_AIC_ISCR 0x12c /* Interrupt Set Command Register */
+#define AT91_AIC_EOICR 0x130 /* End of Interrupt Command Register */
+#define AT91_AIC_SPU 0x134 /* Spurious Interrupt Vector Register */
+#define AT91_AIC_DCR 0x138 /* Debug Control Register */
#define AT91_AIC_DCR_PROT (1 << 0) /* Protection Mode */
#define AT91_AIC_DCR_GMSK (1 << 1) /* General Mask */
-#define AT91_AIC_FFER (AT91_AIC + 0x140) /* Fast Forcing Enable Register [SAM9 only] */
-#define AT91_AIC_FFDR (AT91_AIC + 0x144) /* Fast Forcing Disable Register [SAM9 only] */
-#define AT91_AIC_FFSR (AT91_AIC + 0x148) /* Fast Forcing Status Register [SAM9 only] */
+#define AT91_AIC_FFER 0x140 /* Fast Forcing Enable Register [SAM9 only] */
+#define AT91_AIC_FFDR 0x144 /* Fast Forcing Disable Register [SAM9 only] */
+#define AT91_AIC_FFSR 0x148 /* Fast Forcing Status Register [SAM9 only] */
#endif
#define dbgu_readl(dbgu, field) \
__raw_readl(AT91_VA_BASE_SYS + dbgu + AT91_DBGU_ ## field)
-#ifdef AT91_DBGU
+#if !defined(CONFIG_ARCH_AT91X40)
#define AT91_DBGU_CR (0x00) /* Control Register */
#define AT91_DBGU_MR (0x04) /* Mode Register */
#define AT91_DBGU_IER (0x08) /* Interrupt Enable Register */
#ifndef AT91_PIT_H
#define AT91_PIT_H
-#define AT91_PIT_MR (AT91_PIT + 0x00) /* Mode Register */
+#define AT91_PIT_MR 0x00 /* Mode Register */
#define AT91_PIT_PITIEN (1 << 25) /* Timer Interrupt Enable */
#define AT91_PIT_PITEN (1 << 24) /* Timer Enabled */
#define AT91_PIT_PIV (0xfffff) /* Periodic Interval Value */
-#define AT91_PIT_SR (AT91_PIT + 0x04) /* Status Register */
+#define AT91_PIT_SR 0x04 /* Status Register */
#define AT91_PIT_PITS (1 << 0) /* Timer Status */
-#define AT91_PIT_PIVR (AT91_PIT + 0x08) /* Periodic Interval Value Register */
-#define AT91_PIT_PIIR (AT91_PIT + 0x0c) /* Periodic Interval Image Register */
+#define AT91_PIT_PIVR 0x08 /* Periodic Interval Value Register */
+#define AT91_PIT_PIIR 0x0c /* Periodic Interval Image Register */
#define AT91_PIT_PICNT (0xfff << 20) /* Interval Counter */
#define AT91_PIT_CPIV (0xfffff) /* Inverval Value */
#ifndef AT91_RTC_H
#define AT91_RTC_H
-#define AT91_RTC_CR (AT91_RTC + 0x00) /* Control Register */
+#define AT91_RTC_CR 0x00 /* Control Register */
#define AT91_RTC_UPDTIM (1 << 0) /* Update Request Time Register */
#define AT91_RTC_UPDCAL (1 << 1) /* Update Request Calendar Register */
#define AT91_RTC_TIMEVSEL (3 << 8) /* Time Event Selection */
#define AT91_RTC_CALEVSEL_MONTH (1 << 16)
#define AT91_RTC_CALEVSEL_YEAR (2 << 16)
-#define AT91_RTC_MR (AT91_RTC + 0x04) /* Mode Register */
+#define AT91_RTC_MR 0x04 /* Mode Register */
#define AT91_RTC_HRMOD (1 << 0) /* 12/24 Hour Mode */
-#define AT91_RTC_TIMR (AT91_RTC + 0x08) /* Time Register */
+#define AT91_RTC_TIMR 0x08 /* Time Register */
#define AT91_RTC_SEC (0x7f << 0) /* Current Second */
#define AT91_RTC_MIN (0x7f << 8) /* Current Minute */
#define AT91_RTC_HOUR (0x3f << 16) /* Current Hour */
#define AT91_RTC_AMPM (1 << 22) /* Ante Meridiem Post Meridiem Indicator */
-#define AT91_RTC_CALR (AT91_RTC + 0x0c) /* Calendar Register */
+#define AT91_RTC_CALR 0x0c /* Calendar Register */
#define AT91_RTC_CENT (0x7f << 0) /* Current Century */
#define AT91_RTC_YEAR (0xff << 8) /* Current Year */
#define AT91_RTC_MONTH (0x1f << 16) /* Current Month */
#define AT91_RTC_DAY (7 << 21) /* Current Day */
#define AT91_RTC_DATE (0x3f << 24) /* Current Date */
-#define AT91_RTC_TIMALR (AT91_RTC + 0x10) /* Time Alarm Register */
+#define AT91_RTC_TIMALR 0x10 /* Time Alarm Register */
#define AT91_RTC_SECEN (1 << 7) /* Second Alarm Enable */
#define AT91_RTC_MINEN (1 << 15) /* Minute Alarm Enable */
#define AT91_RTC_HOUREN (1 << 23) /* Hour Alarm Enable */
-#define AT91_RTC_CALALR (AT91_RTC + 0x14) /* Calendar Alarm Register */
+#define AT91_RTC_CALALR 0x14 /* Calendar Alarm Register */
#define AT91_RTC_MTHEN (1 << 23) /* Month Alarm Enable */
#define AT91_RTC_DATEEN (1 << 31) /* Date Alarm Enable */
-#define AT91_RTC_SR (AT91_RTC + 0x18) /* Status Register */
+#define AT91_RTC_SR 0x18 /* Status Register */
#define AT91_RTC_ACKUPD (1 << 0) /* Acknowledge for Update */
#define AT91_RTC_ALARM (1 << 1) /* Alarm Flag */
#define AT91_RTC_SECEV (1 << 2) /* Second Event */
#define AT91_RTC_TIMEV (1 << 3) /* Time Event */
#define AT91_RTC_CALEV (1 << 4) /* Calendar Event */
-#define AT91_RTC_SCCR (AT91_RTC + 0x1c) /* Status Clear Command Register */
-#define AT91_RTC_IER (AT91_RTC + 0x20) /* Interrupt Enable Register */
-#define AT91_RTC_IDR (AT91_RTC + 0x24) /* Interrupt Disable Register */
-#define AT91_RTC_IMR (AT91_RTC + 0x28) /* Interrupt Mask Register */
+#define AT91_RTC_SCCR 0x1c /* Status Clear Command Register */
+#define AT91_RTC_IER 0x20 /* Interrupt Enable Register */
+#define AT91_RTC_IDR 0x24 /* Interrupt Disable Register */
+#define AT91_RTC_IMR 0x28 /* Interrupt Mask Register */
-#define AT91_RTC_VER (AT91_RTC + 0x2c) /* Valid Entry Register */
+#define AT91_RTC_VER 0x2c /* Valid Entry Register */
#define AT91_RTC_NVTIM (1 << 0) /* Non valid Time */
#define AT91_RTC_NVCAL (1 << 1) /* Non valid Calendar */
#define AT91_RTC_NVTIMALR (1 << 2) /* Non valid Time Alarm */
#ifndef AT91_SHDWC_H
#define AT91_SHDWC_H
-#define AT91_SHDW_CR (AT91_SHDWC + 0x00) /* Shut Down Control Register */
+#ifndef __ASSEMBLY__
+extern void __iomem *at91_shdwc_base;
+
+#define at91_shdwc_read(field) \
+ __raw_readl(at91_shdwc_base + field)
+
+#define at91_shdwc_write(field, value) \
+ __raw_writel(value, at91_shdwc_base + field);
+#endif
+
+#define AT91_SHDW_CR 0x00 /* Shut Down Control Register */
#define AT91_SHDW_SHDW (1 << 0) /* Shut Down command */
#define AT91_SHDW_KEY (0xa5 << 24) /* KEY Password */
-#define AT91_SHDW_MR (AT91_SHDWC + 0x04) /* Shut Down Mode Register */
+#define AT91_SHDW_MR 0x04 /* Shut Down Mode Register */
#define AT91_SHDW_WKMODE0 (3 << 0) /* Wake-up 0 Mode Selection */
#define AT91_SHDW_WKMODE0_NONE 0
#define AT91_SHDW_WKMODE0_HIGH 1
#define AT91_SHDW_CPTWK0_(x) ((x) << 4)
#define AT91_SHDW_RTTWKEN (1 << 16) /* Real Time Timer Wake-up Enable */
-#define AT91_SHDW_SR (AT91_SHDWC + 0x08) /* Shut Down Status Register */
+#define AT91_SHDW_SR 0x08 /* Shut Down Status Register */
#define AT91_SHDW_WAKEUP0 (1 << 0) /* Wake-up 0 Status */
#define AT91_SHDW_RTTWK (1 << 16) /* Real-time Timer Wake-up */
#define AT91_SHDW_RTCWK (1 << 17) /* Real-time Clock Wake-up [SAM9RL] */
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
-#define AT91_ECC (0xffffe200 - AT91_BASE_SYS)
#define AT91_BCRAMC (0xffffe400 - AT91_BASE_SYS)
#define AT91_DDRSDRC0 (0xffffe600 - AT91_BASE_SYS)
-#define AT91_SMC (0xffffe800 - AT91_BASE_SYS)
#define AT91_MATRIX (0xffffea00 - AT91_BASE_SYS)
-#define AT91_CCFG (0xffffeb10 - AT91_BASE_SYS)
-#define AT91_DMA (0xffffec00 - AT91_BASE_SYS)
-#define AT91_DBGU (0xffffee00 - AT91_BASE_SYS)
-#define AT91_AIC (0xfffff000 - AT91_BASE_SYS)
-#define AT91_PIOA (0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOB (0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOC (0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOD (0xfffff800 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS)
-#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS)
-#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS)
-#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS)
-#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS)
#define AT91_GPBR (cpu_is_at91cap9_revB() ? \
(0xfffffd50 - AT91_BASE_SYS) : \
(0xfffffd60 - AT91_BASE_SYS))
+#define AT91CAP9_BASE_ECC 0xffffe200
+#define AT91CAP9_BASE_DMA 0xffffec00
+#define AT91CAP9_BASE_SMC 0xffffe800
+#define AT91CAP9_BASE_DBGU AT91_BASE_DBGU1
+#define AT91CAP9_BASE_PIOA 0xfffff200
+#define AT91CAP9_BASE_PIOB 0xfffff400
+#define AT91CAP9_BASE_PIOC 0xfffff600
+#define AT91CAP9_BASE_PIOD 0xfffff800
+#define AT91CAP9_BASE_SHDWC 0xfffffd10
+#define AT91CAP9_BASE_RTT 0xfffffd20
+#define AT91CAP9_BASE_PIT 0xfffffd30
+#define AT91CAP9_BASE_WDT 0xfffffd40
+
#define AT91_USART0 AT91CAP9_BASE_US0
#define AT91_USART1 AT91CAP9_BASE_US1
#define AT91_USART2 AT91CAP9_BASE_US2
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
-#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) /* Advanced Interrupt Controller */
-#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS) /* Debug Unit */
-#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS) /* PIO Controller A */
-#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS) /* PIO Controller B */
-#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS) /* PIO Controller C */
-#define AT91_PIOD (0xfffffa00 - AT91_BASE_SYS) /* PIO Controller D */
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) /* Power Management Controller */
#define AT91_ST (0xfffffd00 - AT91_BASE_SYS) /* System Timer */
-#define AT91_RTC (0xfffffe00 - AT91_BASE_SYS) /* Real-Time Clock */
#define AT91_MC (0xffffff00 - AT91_BASE_SYS) /* Memory Controllers */
+#define AT91RM9200_BASE_DBGU AT91_BASE_DBGU0 /* Debug Unit */
+#define AT91RM9200_BASE_PIOA 0xfffff400 /* PIO Controller A */
+#define AT91RM9200_BASE_PIOB 0xfffff600 /* PIO Controller B */
+#define AT91RM9200_BASE_PIOC 0xfffff800 /* PIO Controller C */
+#define AT91RM9200_BASE_PIOD 0xfffffa00 /* PIO Controller D */
+#define AT91RM9200_BASE_RTC 0xfffffe00 /* Real-Time Clock */
+
#define AT91_USART0 AT91RM9200_BASE_US0
#define AT91_USART1 AT91RM9200_BASE_US1
#define AT91_USART2 AT91RM9200_BASE_US2
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
-#define AT91_ECC (0xffffe800 - AT91_BASE_SYS)
#define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS)
-#define AT91_SMC (0xffffec00 - AT91_BASE_SYS)
#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS)
-#define AT91_CCFG (0xffffef10 - AT91_BASE_SYS)
-#define AT91_AIC (0xfffff000 - AT91_BASE_SYS)
-#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS)
-#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS)
-#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS)
-#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS)
-#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS)
+#define AT91SAM9260_BASE_ECC 0xffffe800
+#define AT91SAM9260_BASE_SMC 0xffffec00
+#define AT91SAM9260_BASE_DBGU AT91_BASE_DBGU0
+#define AT91SAM9260_BASE_PIOA 0xfffff400
+#define AT91SAM9260_BASE_PIOB 0xfffff600
+#define AT91SAM9260_BASE_PIOC 0xfffff800
+#define AT91SAM9260_BASE_SHDWC 0xfffffd10
+#define AT91SAM9260_BASE_RTT 0xfffffd20
+#define AT91SAM9260_BASE_PIT 0xfffffd30
+#define AT91SAM9260_BASE_WDT 0xfffffd40
+
#define AT91_USART0 AT91SAM9260_BASE_US0
#define AT91_USART1 AT91SAM9260_BASE_US1
#define AT91_USART2 AT91SAM9260_BASE_US2
* System Peripherals (offset from AT91_BASE_SYS)
*/
#define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS)
-#define AT91_SMC (0xffffec00 - AT91_BASE_SYS)
#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS)
-#define AT91_AIC (0xfffff000 - AT91_BASE_SYS)
-#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS)
-#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS)
-#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS)
-#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS)
-#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS)
+#define AT91SAM9261_BASE_SMC 0xffffec00
+#define AT91SAM9261_BASE_DBGU AT91_BASE_DBGU0
+#define AT91SAM9261_BASE_PIOA 0xfffff400
+#define AT91SAM9261_BASE_PIOB 0xfffff600
+#define AT91SAM9261_BASE_PIOC 0xfffff800
+#define AT91SAM9261_BASE_SHDWC 0xfffffd10
+#define AT91SAM9261_BASE_RTT 0xfffffd20
+#define AT91SAM9261_BASE_PIT 0xfffffd30
+#define AT91SAM9261_BASE_WDT 0xfffffd40
+
#define AT91_USART0 AT91SAM9261_BASE_US0
#define AT91_USART1 AT91SAM9261_BASE_US1
#define AT91_USART2 AT91SAM9261_BASE_US2
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
-#define AT91_ECC0 (0xffffe000 - AT91_BASE_SYS)
#define AT91_SDRAMC0 (0xffffe200 - AT91_BASE_SYS)
-#define AT91_SMC0 (0xffffe400 - AT91_BASE_SYS)
-#define AT91_ECC1 (0xffffe600 - AT91_BASE_SYS)
#define AT91_SDRAMC1 (0xffffe800 - AT91_BASE_SYS)
-#define AT91_SMC1 (0xffffea00 - AT91_BASE_SYS)
#define AT91_MATRIX (0xffffec00 - AT91_BASE_SYS)
-#define AT91_CCFG (0xffffed10 - AT91_BASE_SYS)
-#define AT91_DBGU (0xffffee00 - AT91_BASE_SYS)
-#define AT91_AIC (0xfffff000 - AT91_BASE_SYS)
-#define AT91_PIOA (0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOB (0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOC (0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOD (0xfffff800 - AT91_BASE_SYS)
-#define AT91_PIOE (0xfffffa00 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS)
-#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS)
-#define AT91_RTT0 (0xfffffd20 - AT91_BASE_SYS)
-#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS)
-#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS)
-#define AT91_RTT1 (0xfffffd50 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS)
+#define AT91SAM9263_BASE_ECC0 0xffffe000
+#define AT91SAM9263_BASE_SMC0 0xffffe400
+#define AT91SAM9263_BASE_ECC1 0xffffe600
+#define AT91SAM9263_BASE_SMC1 0xffffea00
+#define AT91SAM9263_BASE_DBGU AT91_BASE_DBGU1
+#define AT91SAM9263_BASE_PIOA 0xfffff200
+#define AT91SAM9263_BASE_PIOB 0xfffff400
+#define AT91SAM9263_BASE_PIOC 0xfffff600
+#define AT91SAM9263_BASE_PIOD 0xfffff800
+#define AT91SAM9263_BASE_PIOE 0xfffffa00
+#define AT91SAM9263_BASE_SHDWC 0xfffffd10
+#define AT91SAM9263_BASE_RTT0 0xfffffd20
+#define AT91SAM9263_BASE_PIT 0xfffffd30
+#define AT91SAM9263_BASE_WDT 0xfffffd40
+#define AT91SAM9263_BASE_RTT1 0xfffffd50
+
#define AT91_USART0 AT91SAM9263_BASE_US0
#define AT91_USART1 AT91SAM9263_BASE_US1
#define AT91_USART2 AT91SAM9263_BASE_US2
#ifndef AT91SAM9_SMC_H
#define AT91SAM9_SMC_H
-#define AT91_SMC_SETUP(n) (AT91_SMC + 0x00 + ((n)*0x10)) /* Setup Register for CS n */
+#include <mach/cpu.h>
+
+#define AT91_SMC_SETUP 0x00 /* Setup Register for CS n */
#define AT91_SMC_NWESETUP (0x3f << 0) /* NWE Setup Length */
#define AT91_SMC_NWESETUP_(x) ((x) << 0)
#define AT91_SMC_NCS_WRSETUP (0x3f << 8) /* NCS Setup Length in Write Access */
#define AT91_SMC_NCS_RDSETUP (0x3f << 24) /* NCS Setup Length in Read Access */
#define AT91_SMC_NCS_RDSETUP_(x) ((x) << 24)
-#define AT91_SMC_PULSE(n) (AT91_SMC + 0x04 + ((n)*0x10)) /* Pulse Register for CS n */
+#define AT91_SMC_PULSE 0x04 /* Pulse Register for CS n */
#define AT91_SMC_NWEPULSE (0x7f << 0) /* NWE Pulse Length */
#define AT91_SMC_NWEPULSE_(x) ((x) << 0)
#define AT91_SMC_NCS_WRPULSE (0x7f << 8) /* NCS Pulse Length in Write Access */
#define AT91_SMC_NCS_RDPULSE (0x7f << 24) /* NCS Pulse Length in Read Access */
#define AT91_SMC_NCS_RDPULSE_(x)((x) << 24)
-#define AT91_SMC_CYCLE(n) (AT91_SMC + 0x08 + ((n)*0x10)) /* Cycle Register for CS n */
+#define AT91_SMC_CYCLE 0x08 /* Cycle Register for CS n */
#define AT91_SMC_NWECYCLE (0x1ff << 0 ) /* Total Write Cycle Length */
#define AT91_SMC_NWECYCLE_(x) ((x) << 0)
#define AT91_SMC_NRDCYCLE (0x1ff << 16) /* Total Read Cycle Length */
#define AT91_SMC_NRDCYCLE_(x) ((x) << 16)
-#define AT91_SMC_MODE(n) (AT91_SMC + 0x0c + ((n)*0x10)) /* Mode Register for CS n */
+#define AT91_SMC_MODE 0x0c /* Mode Register for CS n */
#define AT91_SMC_READMODE (1 << 0) /* Read Mode */
#define AT91_SMC_WRITEMODE (1 << 1) /* Write Mode */
#define AT91_SMC_EXNWMODE (3 << 4) /* NWAIT Mode */
#define AT91_SMC_PS_16 (2 << 28)
#define AT91_SMC_PS_32 (3 << 28)
-#if defined(AT91_SMC1) /* The AT91SAM9263 has 2 Static Memory contollers */
-#define AT91_SMC1_SETUP(n) (AT91_SMC1 + 0x00 + ((n)*0x10)) /* Setup Register for CS n */
-#define AT91_SMC1_PULSE(n) (AT91_SMC1 + 0x04 + ((n)*0x10)) /* Pulse Register for CS n */
-#define AT91_SMC1_CYCLE(n) (AT91_SMC1 + 0x08 + ((n)*0x10)) /* Cycle Register for CS n */
-#define AT91_SMC1_MODE(n) (AT91_SMC1 + 0x0c + ((n)*0x10)) /* Mode Register for CS n */
-#endif
-
#endif
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
-#define AT91_ECC (0xffffe200 - AT91_BASE_SYS)
#define AT91_DDRSDRC1 (0xffffe400 - AT91_BASE_SYS)
#define AT91_DDRSDRC0 (0xffffe600 - AT91_BASE_SYS)
-#define AT91_SMC (0xffffe800 - AT91_BASE_SYS)
#define AT91_MATRIX (0xffffea00 - AT91_BASE_SYS)
-#define AT91_DMA (0xffffec00 - AT91_BASE_SYS)
-#define AT91_DBGU (0xffffee00 - AT91_BASE_SYS)
-#define AT91_AIC (0xfffff000 - AT91_BASE_SYS)
-#define AT91_PIOA (0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOB (0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOC (0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOD (0xfffff800 - AT91_BASE_SYS)
-#define AT91_PIOE (0xfffffa00 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS)
-#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS)
-#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS)
-#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS)
-#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS)
-#define AT91_RTC (0xfffffdb0 - AT91_BASE_SYS)
+
+#define AT91SAM9G45_BASE_ECC 0xffffe200
+#define AT91SAM9G45_BASE_DMA 0xffffec00
+#define AT91SAM9G45_BASE_SMC 0xffffe800
+#define AT91SAM9G45_BASE_DBGU AT91_BASE_DBGU1
+#define AT91SAM9G45_BASE_PIOA 0xfffff200
+#define AT91SAM9G45_BASE_PIOB 0xfffff400
+#define AT91SAM9G45_BASE_PIOC 0xfffff600
+#define AT91SAM9G45_BASE_PIOD 0xfffff800
+#define AT91SAM9G45_BASE_PIOE 0xfffffa00
+#define AT91SAM9G45_BASE_SHDWC 0xfffffd10
+#define AT91SAM9G45_BASE_RTT 0xfffffd20
+#define AT91SAM9G45_BASE_PIT 0xfffffd30
+#define AT91SAM9G45_BASE_WDT 0xfffffd40
+#define AT91SAM9G45_BASE_RTC 0xfffffdb0
#define AT91_USART0 AT91SAM9G45_BASE_US0
#define AT91_USART1 AT91SAM9G45_BASE_US1
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
-#define AT91_DMA (0xffffe600 - AT91_BASE_SYS)
-#define AT91_ECC (0xffffe800 - AT91_BASE_SYS)
#define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS)
-#define AT91_SMC (0xffffec00 - AT91_BASE_SYS)
#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS)
-#define AT91_CCFG (0xffffef10 - AT91_BASE_SYS)
-#define AT91_AIC (0xfffff000 - AT91_BASE_SYS)
-#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS)
-#define AT91_PIOD (0xfffffa00 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS)
-#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS)
-#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS)
-#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS)
-#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS)
#define AT91_SCKCR (0xfffffd50 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS)
-#define AT91_RTC (0xfffffe00 - AT91_BASE_SYS)
+
+#define AT91SAM9RL_BASE_DMA 0xffffe600
+#define AT91SAM9RL_BASE_ECC 0xffffe800
+#define AT91SAM9RL_BASE_SMC 0xffffec00
+#define AT91SAM9RL_BASE_DBGU AT91_BASE_DBGU0
+#define AT91SAM9RL_BASE_PIOA 0xfffff400
+#define AT91SAM9RL_BASE_PIOB 0xfffff600
+#define AT91SAM9RL_BASE_PIOC 0xfffff800
+#define AT91SAM9RL_BASE_PIOD 0xfffffa00
+#define AT91SAM9RL_BASE_SHDWC 0xfffffd10
+#define AT91SAM9RL_BASE_RTT 0xfffffd20
+#define AT91SAM9RL_BASE_PIT 0xfffffd30
+#define AT91SAM9RL_BASE_WDT 0xfffffd40
+#define AT91SAM9RL_BASE_RTC 0xfffffe00
#define AT91_USART0 AT91SAM9RL_BASE_US0
#define AT91_USART1 AT91SAM9RL_BASE_US1
#define AT91_PIOA (0xffff0000 - AT91_BASE_SYS) /* PIO Controller A */
#define AT91_PS (0xffff4000 - AT91_BASE_SYS) /* Power Save */
#define AT91_WD (0xffff8000 - AT91_BASE_SYS) /* Watchdog Timer */
-#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) /* Advanced Interrupt Controller */
/*
* The AT91x40 series doesn't have a debug unit like the other AT91 parts.
#include <linux/atmel-mci.h>
#include <sound/atmel-ac97c.h>
#include <linux/serial.h>
+#include <linux/platform_data/macb.h>
/* USB Device */
struct at91_udc_data {
- u8 vbus_pin; /* high == host powering us */
+ int vbus_pin; /* high == host powering us */
u8 vbus_active_low; /* vbus polarity */
u8 vbus_polled; /* Use polling, not interrupt */
- u8 pullup_pin; /* active == D+ pulled up */
+ int pullup_pin; /* active == D+ pulled up */
u8 pullup_active_low; /* true == pullup_pin is active low */
};
extern void __init at91_add_device_udc(struct at91_udc_data *data);
/* Compact Flash */
struct at91_cf_data {
- u8 irq_pin; /* I/O IRQ */
- u8 det_pin; /* Card detect */
- u8 vcc_pin; /* power switching */
- u8 rst_pin; /* card reset */
+ int irq_pin; /* I/O IRQ */
+ int det_pin; /* Card detect */
+ int vcc_pin; /* power switching */
+ int rst_pin; /* card reset */
u8 chipselect; /* EBI Chip Select number */
u8 flags;
#define AT91_CF_TRUE_IDE 0x01
/* MMC / SD */
/* at91_mci platform config */
struct at91_mmc_data {
- u8 det_pin; /* card detect IRQ */
+ int det_pin; /* card detect IRQ */
unsigned slot_b:1; /* uses Slot B */
unsigned wire4:1; /* (SD) supports DAT0..DAT3 */
- u8 wp_pin; /* (SD) writeprotect detect */
- u8 vcc_pin; /* power switching (high == on) */
+ int wp_pin; /* (SD) writeprotect detect */
+ int vcc_pin; /* power switching (high == on) */
};
extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data);
/* atmel-mci platform config */
extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data);
- /* Ethernet (EMAC & MACB) */
-struct at91_eth_data {
- u32 phy_mask;
- u8 phy_irq_pin; /* PHY IRQ */
- u8 is_rmii; /* using RMII interface? */
-};
-extern void __init at91_add_device_eth(struct at91_eth_data *data);
-
-#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9) \
- || defined(CONFIG_ARCH_AT91SAM9G45)
-#define eth_platform_data at91_eth_data
-#endif
+extern void __init at91_add_device_eth(struct macb_platform_data *data);
/* USB Host */
struct at91_usbh_data {
u8 ports; /* number of ports on root hub */
- u8 vbus_pin[2]; /* port power-control pin */
+ int vbus_pin[2]; /* port power-control pin */
u8 vbus_pin_inverted;
u8 overcurrent_supported;
- u8 overcurrent_pin[2];
+ int overcurrent_pin[2];
u8 overcurrent_status[2];
u8 overcurrent_changed[2];
};
/* NAND / SmartMedia */
struct atmel_nand_data {
- u8 enable_pin; /* chip enable */
- u8 det_pin; /* card detect */
- u8 rdy_pin; /* ready/busy */
+ int enable_pin; /* chip enable */
+ int det_pin; /* card detect */
+ int rdy_pin; /* ready/busy */
u8 rdy_pin_active_low; /* rdy_pin value is inverted */
u8 ale; /* address line number connected to ALE */
u8 cle; /* address line number connected to CLE */
#include <mach/hardware.h>
#include <mach/at91_dbgu.h>
+#if defined(CONFIG_AT91_DEBUG_LL_DBGU0)
+#define AT91_DBGU AT91_BASE_DBGU0
+#else
+#define AT91_DBGU AT91_BASE_DBGU1
+#endif
+
.macro addruart, rp, rv, tmp
- ldr \rp, =(AT91_BASE_SYS + AT91_DBGU) @ System peripherals (phys address)
- ldr \rv, =(AT91_VA_BASE_SYS + AT91_DBGU) @ System peripherals (virt address)
+ ldr \rp, =AT91_DBGU @ System peripherals (phys address)
+ ldr \rv, =AT91_IO_P2V(AT91_DBGU) @ System peripherals (virt address)
.endm
.macro senduart,rd,rx
.endm
.macro get_irqnr_preamble, base, tmp
- ldr \base, =(AT91_VA_BASE_SYS + AT91_AIC) @ base virtual address of AIC peripheral
+ ldr \base, =at91_aic_base @ base virtual address of AIC peripheral
+ ldr \base, [\base]
.endm
.macro arch_ret_to_user, tmp1, tmp2
.endm
.macro get_irqnr_and_base, irqnr, irqstat, base, tmp
- ldr \irqnr, [\base, #(AT91_AIC_IVR - AT91_AIC)] @ read IRQ vector register: de-asserts nIRQ to processor (and clears interrupt)
- ldr \irqstat, [\base, #(AT91_AIC_ISR - AT91_AIC)] @ read interrupt source number
- teq \irqstat, #0 @ ISR is 0 when no current interrupt, or spurious interrupt
- streq \tmp, [\base, #(AT91_AIC_EOICR - AT91_AIC)] @ not going to be handled further, then ACK it now.
+ ldr \irqnr, [\base, #AT91_AIC_IVR] @ read IRQ vector register: de-asserts nIRQ to processor (and clears interrupt)
+ ldr \irqstat, [\base, #AT91_AIC_ISR] @ read interrupt source number
+ teq \irqstat, #0 @ ISR is 0 when no current interrupt, or spurious interrupt
+ streq \tmp, [\base, #AT91_AIC_EOICR] @ not going to be handled further, then ACK it now.
.endm
#include <linux/kernel.h>
#include <asm/irq.h>
-#define PIN_BASE NR_AIC_IRQS
-
#define MAX_GPIO_BANKS 5
-#define NR_BUILTIN_GPIO (PIN_BASE + (MAX_GPIO_BANKS * 32))
+#define NR_BUILTIN_GPIO (MAX_GPIO_BANKS * 32)
/* these pin numbers double as IRQ numbers, like AT91xxx_ID_* values */
-#define AT91_PIN_PA0 (PIN_BASE + 0x00 + 0)
-#define AT91_PIN_PA1 (PIN_BASE + 0x00 + 1)
-#define AT91_PIN_PA2 (PIN_BASE + 0x00 + 2)
-#define AT91_PIN_PA3 (PIN_BASE + 0x00 + 3)
-#define AT91_PIN_PA4 (PIN_BASE + 0x00 + 4)
-#define AT91_PIN_PA5 (PIN_BASE + 0x00 + 5)
-#define AT91_PIN_PA6 (PIN_BASE + 0x00 + 6)
-#define AT91_PIN_PA7 (PIN_BASE + 0x00 + 7)
-#define AT91_PIN_PA8 (PIN_BASE + 0x00 + 8)
-#define AT91_PIN_PA9 (PIN_BASE + 0x00 + 9)
-#define AT91_PIN_PA10 (PIN_BASE + 0x00 + 10)
-#define AT91_PIN_PA11 (PIN_BASE + 0x00 + 11)
-#define AT91_PIN_PA12 (PIN_BASE + 0x00 + 12)
-#define AT91_PIN_PA13 (PIN_BASE + 0x00 + 13)
-#define AT91_PIN_PA14 (PIN_BASE + 0x00 + 14)
-#define AT91_PIN_PA15 (PIN_BASE + 0x00 + 15)
-#define AT91_PIN_PA16 (PIN_BASE + 0x00 + 16)
-#define AT91_PIN_PA17 (PIN_BASE + 0x00 + 17)
-#define AT91_PIN_PA18 (PIN_BASE + 0x00 + 18)
-#define AT91_PIN_PA19 (PIN_BASE + 0x00 + 19)
-#define AT91_PIN_PA20 (PIN_BASE + 0x00 + 20)
-#define AT91_PIN_PA21 (PIN_BASE + 0x00 + 21)
-#define AT91_PIN_PA22 (PIN_BASE + 0x00 + 22)
-#define AT91_PIN_PA23 (PIN_BASE + 0x00 + 23)
-#define AT91_PIN_PA24 (PIN_BASE + 0x00 + 24)
-#define AT91_PIN_PA25 (PIN_BASE + 0x00 + 25)
-#define AT91_PIN_PA26 (PIN_BASE + 0x00 + 26)
-#define AT91_PIN_PA27 (PIN_BASE + 0x00 + 27)
-#define AT91_PIN_PA28 (PIN_BASE + 0x00 + 28)
-#define AT91_PIN_PA29 (PIN_BASE + 0x00 + 29)
-#define AT91_PIN_PA30 (PIN_BASE + 0x00 + 30)
-#define AT91_PIN_PA31 (PIN_BASE + 0x00 + 31)
-
-#define AT91_PIN_PB0 (PIN_BASE + 0x20 + 0)
-#define AT91_PIN_PB1 (PIN_BASE + 0x20 + 1)
-#define AT91_PIN_PB2 (PIN_BASE + 0x20 + 2)
-#define AT91_PIN_PB3 (PIN_BASE + 0x20 + 3)
-#define AT91_PIN_PB4 (PIN_BASE + 0x20 + 4)
-#define AT91_PIN_PB5 (PIN_BASE + 0x20 + 5)
-#define AT91_PIN_PB6 (PIN_BASE + 0x20 + 6)
-#define AT91_PIN_PB7 (PIN_BASE + 0x20 + 7)
-#define AT91_PIN_PB8 (PIN_BASE + 0x20 + 8)
-#define AT91_PIN_PB9 (PIN_BASE + 0x20 + 9)
-#define AT91_PIN_PB10 (PIN_BASE + 0x20 + 10)
-#define AT91_PIN_PB11 (PIN_BASE + 0x20 + 11)
-#define AT91_PIN_PB12 (PIN_BASE + 0x20 + 12)
-#define AT91_PIN_PB13 (PIN_BASE + 0x20 + 13)
-#define AT91_PIN_PB14 (PIN_BASE + 0x20 + 14)
-#define AT91_PIN_PB15 (PIN_BASE + 0x20 + 15)
-#define AT91_PIN_PB16 (PIN_BASE + 0x20 + 16)
-#define AT91_PIN_PB17 (PIN_BASE + 0x20 + 17)
-#define AT91_PIN_PB18 (PIN_BASE + 0x20 + 18)
-#define AT91_PIN_PB19 (PIN_BASE + 0x20 + 19)
-#define AT91_PIN_PB20 (PIN_BASE + 0x20 + 20)
-#define AT91_PIN_PB21 (PIN_BASE + 0x20 + 21)
-#define AT91_PIN_PB22 (PIN_BASE + 0x20 + 22)
-#define AT91_PIN_PB23 (PIN_BASE + 0x20 + 23)
-#define AT91_PIN_PB24 (PIN_BASE + 0x20 + 24)
-#define AT91_PIN_PB25 (PIN_BASE + 0x20 + 25)
-#define AT91_PIN_PB26 (PIN_BASE + 0x20 + 26)
-#define AT91_PIN_PB27 (PIN_BASE + 0x20 + 27)
-#define AT91_PIN_PB28 (PIN_BASE + 0x20 + 28)
-#define AT91_PIN_PB29 (PIN_BASE + 0x20 + 29)
-#define AT91_PIN_PB30 (PIN_BASE + 0x20 + 30)
-#define AT91_PIN_PB31 (PIN_BASE + 0x20 + 31)
-
-#define AT91_PIN_PC0 (PIN_BASE + 0x40 + 0)
-#define AT91_PIN_PC1 (PIN_BASE + 0x40 + 1)
-#define AT91_PIN_PC2 (PIN_BASE + 0x40 + 2)
-#define AT91_PIN_PC3 (PIN_BASE + 0x40 + 3)
-#define AT91_PIN_PC4 (PIN_BASE + 0x40 + 4)
-#define AT91_PIN_PC5 (PIN_BASE + 0x40 + 5)
-#define AT91_PIN_PC6 (PIN_BASE + 0x40 + 6)
-#define AT91_PIN_PC7 (PIN_BASE + 0x40 + 7)
-#define AT91_PIN_PC8 (PIN_BASE + 0x40 + 8)
-#define AT91_PIN_PC9 (PIN_BASE + 0x40 + 9)
-#define AT91_PIN_PC10 (PIN_BASE + 0x40 + 10)
-#define AT91_PIN_PC11 (PIN_BASE + 0x40 + 11)
-#define AT91_PIN_PC12 (PIN_BASE + 0x40 + 12)
-#define AT91_PIN_PC13 (PIN_BASE + 0x40 + 13)
-#define AT91_PIN_PC14 (PIN_BASE + 0x40 + 14)
-#define AT91_PIN_PC15 (PIN_BASE + 0x40 + 15)
-#define AT91_PIN_PC16 (PIN_BASE + 0x40 + 16)
-#define AT91_PIN_PC17 (PIN_BASE + 0x40 + 17)
-#define AT91_PIN_PC18 (PIN_BASE + 0x40 + 18)
-#define AT91_PIN_PC19 (PIN_BASE + 0x40 + 19)
-#define AT91_PIN_PC20 (PIN_BASE + 0x40 + 20)
-#define AT91_PIN_PC21 (PIN_BASE + 0x40 + 21)
-#define AT91_PIN_PC22 (PIN_BASE + 0x40 + 22)
-#define AT91_PIN_PC23 (PIN_BASE + 0x40 + 23)
-#define AT91_PIN_PC24 (PIN_BASE + 0x40 + 24)
-#define AT91_PIN_PC25 (PIN_BASE + 0x40 + 25)
-#define AT91_PIN_PC26 (PIN_BASE + 0x40 + 26)
-#define AT91_PIN_PC27 (PIN_BASE + 0x40 + 27)
-#define AT91_PIN_PC28 (PIN_BASE + 0x40 + 28)
-#define AT91_PIN_PC29 (PIN_BASE + 0x40 + 29)
-#define AT91_PIN_PC30 (PIN_BASE + 0x40 + 30)
-#define AT91_PIN_PC31 (PIN_BASE + 0x40 + 31)
-
-#define AT91_PIN_PD0 (PIN_BASE + 0x60 + 0)
-#define AT91_PIN_PD1 (PIN_BASE + 0x60 + 1)
-#define AT91_PIN_PD2 (PIN_BASE + 0x60 + 2)
-#define AT91_PIN_PD3 (PIN_BASE + 0x60 + 3)
-#define AT91_PIN_PD4 (PIN_BASE + 0x60 + 4)
-#define AT91_PIN_PD5 (PIN_BASE + 0x60 + 5)
-#define AT91_PIN_PD6 (PIN_BASE + 0x60 + 6)
-#define AT91_PIN_PD7 (PIN_BASE + 0x60 + 7)
-#define AT91_PIN_PD8 (PIN_BASE + 0x60 + 8)
-#define AT91_PIN_PD9 (PIN_BASE + 0x60 + 9)
-#define AT91_PIN_PD10 (PIN_BASE + 0x60 + 10)
-#define AT91_PIN_PD11 (PIN_BASE + 0x60 + 11)
-#define AT91_PIN_PD12 (PIN_BASE + 0x60 + 12)
-#define AT91_PIN_PD13 (PIN_BASE + 0x60 + 13)
-#define AT91_PIN_PD14 (PIN_BASE + 0x60 + 14)
-#define AT91_PIN_PD15 (PIN_BASE + 0x60 + 15)
-#define AT91_PIN_PD16 (PIN_BASE + 0x60 + 16)
-#define AT91_PIN_PD17 (PIN_BASE + 0x60 + 17)
-#define AT91_PIN_PD18 (PIN_BASE + 0x60 + 18)
-#define AT91_PIN_PD19 (PIN_BASE + 0x60 + 19)
-#define AT91_PIN_PD20 (PIN_BASE + 0x60 + 20)
-#define AT91_PIN_PD21 (PIN_BASE + 0x60 + 21)
-#define AT91_PIN_PD22 (PIN_BASE + 0x60 + 22)
-#define AT91_PIN_PD23 (PIN_BASE + 0x60 + 23)
-#define AT91_PIN_PD24 (PIN_BASE + 0x60 + 24)
-#define AT91_PIN_PD25 (PIN_BASE + 0x60 + 25)
-#define AT91_PIN_PD26 (PIN_BASE + 0x60 + 26)
-#define AT91_PIN_PD27 (PIN_BASE + 0x60 + 27)
-#define AT91_PIN_PD28 (PIN_BASE + 0x60 + 28)
-#define AT91_PIN_PD29 (PIN_BASE + 0x60 + 29)
-#define AT91_PIN_PD30 (PIN_BASE + 0x60 + 30)
-#define AT91_PIN_PD31 (PIN_BASE + 0x60 + 31)
-
-#define AT91_PIN_PE0 (PIN_BASE + 0x80 + 0)
-#define AT91_PIN_PE1 (PIN_BASE + 0x80 + 1)
-#define AT91_PIN_PE2 (PIN_BASE + 0x80 + 2)
-#define AT91_PIN_PE3 (PIN_BASE + 0x80 + 3)
-#define AT91_PIN_PE4 (PIN_BASE + 0x80 + 4)
-#define AT91_PIN_PE5 (PIN_BASE + 0x80 + 5)
-#define AT91_PIN_PE6 (PIN_BASE + 0x80 + 6)
-#define AT91_PIN_PE7 (PIN_BASE + 0x80 + 7)
-#define AT91_PIN_PE8 (PIN_BASE + 0x80 + 8)
-#define AT91_PIN_PE9 (PIN_BASE + 0x80 + 9)
-#define AT91_PIN_PE10 (PIN_BASE + 0x80 + 10)
-#define AT91_PIN_PE11 (PIN_BASE + 0x80 + 11)
-#define AT91_PIN_PE12 (PIN_BASE + 0x80 + 12)
-#define AT91_PIN_PE13 (PIN_BASE + 0x80 + 13)
-#define AT91_PIN_PE14 (PIN_BASE + 0x80 + 14)
-#define AT91_PIN_PE15 (PIN_BASE + 0x80 + 15)
-#define AT91_PIN_PE16 (PIN_BASE + 0x80 + 16)
-#define AT91_PIN_PE17 (PIN_BASE + 0x80 + 17)
-#define AT91_PIN_PE18 (PIN_BASE + 0x80 + 18)
-#define AT91_PIN_PE19 (PIN_BASE + 0x80 + 19)
-#define AT91_PIN_PE20 (PIN_BASE + 0x80 + 20)
-#define AT91_PIN_PE21 (PIN_BASE + 0x80 + 21)
-#define AT91_PIN_PE22 (PIN_BASE + 0x80 + 22)
-#define AT91_PIN_PE23 (PIN_BASE + 0x80 + 23)
-#define AT91_PIN_PE24 (PIN_BASE + 0x80 + 24)
-#define AT91_PIN_PE25 (PIN_BASE + 0x80 + 25)
-#define AT91_PIN_PE26 (PIN_BASE + 0x80 + 26)
-#define AT91_PIN_PE27 (PIN_BASE + 0x80 + 27)
-#define AT91_PIN_PE28 (PIN_BASE + 0x80 + 28)
-#define AT91_PIN_PE29 (PIN_BASE + 0x80 + 29)
-#define AT91_PIN_PE30 (PIN_BASE + 0x80 + 30)
-#define AT91_PIN_PE31 (PIN_BASE + 0x80 + 31)
+#define AT91_PIN_PA0 (0x00 + 0)
+#define AT91_PIN_PA1 (0x00 + 1)
+#define AT91_PIN_PA2 (0x00 + 2)
+#define AT91_PIN_PA3 (0x00 + 3)
+#define AT91_PIN_PA4 (0x00 + 4)
+#define AT91_PIN_PA5 (0x00 + 5)
+#define AT91_PIN_PA6 (0x00 + 6)
+#define AT91_PIN_PA7 (0x00 + 7)
+#define AT91_PIN_PA8 (0x00 + 8)
+#define AT91_PIN_PA9 (0x00 + 9)
+#define AT91_PIN_PA10 (0x00 + 10)
+#define AT91_PIN_PA11 (0x00 + 11)
+#define AT91_PIN_PA12 (0x00 + 12)
+#define AT91_PIN_PA13 (0x00 + 13)
+#define AT91_PIN_PA14 (0x00 + 14)
+#define AT91_PIN_PA15 (0x00 + 15)
+#define AT91_PIN_PA16 (0x00 + 16)
+#define AT91_PIN_PA17 (0x00 + 17)
+#define AT91_PIN_PA18 (0x00 + 18)
+#define AT91_PIN_PA19 (0x00 + 19)
+#define AT91_PIN_PA20 (0x00 + 20)
+#define AT91_PIN_PA21 (0x00 + 21)
+#define AT91_PIN_PA22 (0x00 + 22)
+#define AT91_PIN_PA23 (0x00 + 23)
+#define AT91_PIN_PA24 (0x00 + 24)
+#define AT91_PIN_PA25 (0x00 + 25)
+#define AT91_PIN_PA26 (0x00 + 26)
+#define AT91_PIN_PA27 (0x00 + 27)
+#define AT91_PIN_PA28 (0x00 + 28)
+#define AT91_PIN_PA29 (0x00 + 29)
+#define AT91_PIN_PA30 (0x00 + 30)
+#define AT91_PIN_PA31 (0x00 + 31)
+
+#define AT91_PIN_PB0 (0x20 + 0)
+#define AT91_PIN_PB1 (0x20 + 1)
+#define AT91_PIN_PB2 (0x20 + 2)
+#define AT91_PIN_PB3 (0x20 + 3)
+#define AT91_PIN_PB4 (0x20 + 4)
+#define AT91_PIN_PB5 (0x20 + 5)
+#define AT91_PIN_PB6 (0x20 + 6)
+#define AT91_PIN_PB7 (0x20 + 7)
+#define AT91_PIN_PB8 (0x20 + 8)
+#define AT91_PIN_PB9 (0x20 + 9)
+#define AT91_PIN_PB10 (0x20 + 10)
+#define AT91_PIN_PB11 (0x20 + 11)
+#define AT91_PIN_PB12 (0x20 + 12)
+#define AT91_PIN_PB13 (0x20 + 13)
+#define AT91_PIN_PB14 (0x20 + 14)
+#define AT91_PIN_PB15 (0x20 + 15)
+#define AT91_PIN_PB16 (0x20 + 16)
+#define AT91_PIN_PB17 (0x20 + 17)
+#define AT91_PIN_PB18 (0x20 + 18)
+#define AT91_PIN_PB19 (0x20 + 19)
+#define AT91_PIN_PB20 (0x20 + 20)
+#define AT91_PIN_PB21 (0x20 + 21)
+#define AT91_PIN_PB22 (0x20 + 22)
+#define AT91_PIN_PB23 (0x20 + 23)
+#define AT91_PIN_PB24 (0x20 + 24)
+#define AT91_PIN_PB25 (0x20 + 25)
+#define AT91_PIN_PB26 (0x20 + 26)
+#define AT91_PIN_PB27 (0x20 + 27)
+#define AT91_PIN_PB28 (0x20 + 28)
+#define AT91_PIN_PB29 (0x20 + 29)
+#define AT91_PIN_PB30 (0x20 + 30)
+#define AT91_PIN_PB31 (0x20 + 31)
+
+#define AT91_PIN_PC0 (0x40 + 0)
+#define AT91_PIN_PC1 (0x40 + 1)
+#define AT91_PIN_PC2 (0x40 + 2)
+#define AT91_PIN_PC3 (0x40 + 3)
+#define AT91_PIN_PC4 (0x40 + 4)
+#define AT91_PIN_PC5 (0x40 + 5)
+#define AT91_PIN_PC6 (0x40 + 6)
+#define AT91_PIN_PC7 (0x40 + 7)
+#define AT91_PIN_PC8 (0x40 + 8)
+#define AT91_PIN_PC9 (0x40 + 9)
+#define AT91_PIN_PC10 (0x40 + 10)
+#define AT91_PIN_PC11 (0x40 + 11)
+#define AT91_PIN_PC12 (0x40 + 12)
+#define AT91_PIN_PC13 (0x40 + 13)
+#define AT91_PIN_PC14 (0x40 + 14)
+#define AT91_PIN_PC15 (0x40 + 15)
+#define AT91_PIN_PC16 (0x40 + 16)
+#define AT91_PIN_PC17 (0x40 + 17)
+#define AT91_PIN_PC18 (0x40 + 18)
+#define AT91_PIN_PC19 (0x40 + 19)
+#define AT91_PIN_PC20 (0x40 + 20)
+#define AT91_PIN_PC21 (0x40 + 21)
+#define AT91_PIN_PC22 (0x40 + 22)
+#define AT91_PIN_PC23 (0x40 + 23)
+#define AT91_PIN_PC24 (0x40 + 24)
+#define AT91_PIN_PC25 (0x40 + 25)
+#define AT91_PIN_PC26 (0x40 + 26)
+#define AT91_PIN_PC27 (0x40 + 27)
+#define AT91_PIN_PC28 (0x40 + 28)
+#define AT91_PIN_PC29 (0x40 + 29)
+#define AT91_PIN_PC30 (0x40 + 30)
+#define AT91_PIN_PC31 (0x40 + 31)
+
+#define AT91_PIN_PD0 (0x60 + 0)
+#define AT91_PIN_PD1 (0x60 + 1)
+#define AT91_PIN_PD2 (0x60 + 2)
+#define AT91_PIN_PD3 (0x60 + 3)
+#define AT91_PIN_PD4 (0x60 + 4)
+#define AT91_PIN_PD5 (0x60 + 5)
+#define AT91_PIN_PD6 (0x60 + 6)
+#define AT91_PIN_PD7 (0x60 + 7)
+#define AT91_PIN_PD8 (0x60 + 8)
+#define AT91_PIN_PD9 (0x60 + 9)
+#define AT91_PIN_PD10 (0x60 + 10)
+#define AT91_PIN_PD11 (0x60 + 11)
+#define AT91_PIN_PD12 (0x60 + 12)
+#define AT91_PIN_PD13 (0x60 + 13)
+#define AT91_PIN_PD14 (0x60 + 14)
+#define AT91_PIN_PD15 (0x60 + 15)
+#define AT91_PIN_PD16 (0x60 + 16)
+#define AT91_PIN_PD17 (0x60 + 17)
+#define AT91_PIN_PD18 (0x60 + 18)
+#define AT91_PIN_PD19 (0x60 + 19)
+#define AT91_PIN_PD20 (0x60 + 20)
+#define AT91_PIN_PD21 (0x60 + 21)
+#define AT91_PIN_PD22 (0x60 + 22)
+#define AT91_PIN_PD23 (0x60 + 23)
+#define AT91_PIN_PD24 (0x60 + 24)
+#define AT91_PIN_PD25 (0x60 + 25)
+#define AT91_PIN_PD26 (0x60 + 26)
+#define AT91_PIN_PD27 (0x60 + 27)
+#define AT91_PIN_PD28 (0x60 + 28)
+#define AT91_PIN_PD29 (0x60 + 29)
+#define AT91_PIN_PD30 (0x60 + 30)
+#define AT91_PIN_PD31 (0x60 + 31)
+
+#define AT91_PIN_PE0 (0x80 + 0)
+#define AT91_PIN_PE1 (0x80 + 1)
+#define AT91_PIN_PE2 (0x80 + 2)
+#define AT91_PIN_PE3 (0x80 + 3)
+#define AT91_PIN_PE4 (0x80 + 4)
+#define AT91_PIN_PE5 (0x80 + 5)
+#define AT91_PIN_PE6 (0x80 + 6)
+#define AT91_PIN_PE7 (0x80 + 7)
+#define AT91_PIN_PE8 (0x80 + 8)
+#define AT91_PIN_PE9 (0x80 + 9)
+#define AT91_PIN_PE10 (0x80 + 10)
+#define AT91_PIN_PE11 (0x80 + 11)
+#define AT91_PIN_PE12 (0x80 + 12)
+#define AT91_PIN_PE13 (0x80 + 13)
+#define AT91_PIN_PE14 (0x80 + 14)
+#define AT91_PIN_PE15 (0x80 + 15)
+#define AT91_PIN_PE16 (0x80 + 16)
+#define AT91_PIN_PE17 (0x80 + 17)
+#define AT91_PIN_PE18 (0x80 + 18)
+#define AT91_PIN_PE19 (0x80 + 19)
+#define AT91_PIN_PE20 (0x80 + 20)
+#define AT91_PIN_PE21 (0x80 + 21)
+#define AT91_PIN_PE22 (0x80 + 22)
+#define AT91_PIN_PE23 (0x80 + 23)
+#define AT91_PIN_PE24 (0x80 + 24)
+#define AT91_PIN_PE25 (0x80 + 25)
+#define AT91_PIN_PE26 (0x80 + 26)
+#define AT91_PIN_PE27 (0x80 + 27)
+#define AT91_PIN_PE28 (0x80 + 28)
+#define AT91_PIN_PE29 (0x80 + 29)
+#define AT91_PIN_PE30 (0x80 + 30)
+#define AT91_PIN_PE31 (0x80 + 31)
#ifndef __ASSEMBLY__
/* setup setup routines, called from board init or driver probe() */
#include <asm/errno.h>
-#define gpio_to_irq(gpio) (gpio)
-#define irq_to_gpio(irq) (irq)
+#define gpio_to_irq(gpio) (gpio + NR_AIC_IRQS)
+#define irq_to_gpio(irq) (irq - NR_AIC_IRQS)
#endif /* __ASSEMBLY__ */
#include <asm/sizes.h>
+/* DBGU base */
+/* rm9200, 9260/9g20, 9261/9g10, 9rl */
+#define AT91_BASE_DBGU0 0xfffff200
+/* 9263, 9g45, cap9 */
+#define AT91_BASE_DBGU1 0xffffee00
+
#if defined(CONFIG_ARCH_AT91RM9200)
#include <mach/at91rm9200.h>
#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20)
#define AT91_BASE_SYS 0xffffc000
#endif
+/*
+ * On all at91 have the Advanced Interrupt Controller starts at address
+ * 0xfffff000
+ */
+#define AT91_AIC 0xfffff000
+
/*
* Peripheral identifiers/interrupts.
*/
* Acknowledge interrupt with AIC after interrupt has been handled.
* (by kernel/irq.c)
*/
-#define irq_finish(irq) do { at91_sys_write(AT91_AIC_EOICR, 0); } while (0)
+#define irq_finish(irq) do { at91_aic_write(AT91_AIC_EOICR, 0); } while (0)
/*
#include <mach/hardware.h>
-#if defined(CONFIG_ARCH_AT91RM9200)
+#ifdef CONFIG_ARCH_AT91X40
-#define CLOCK_TICK_RATE (AT91_SLOW_CLOCK)
-
-#elif defined(CONFIG_ARCH_AT91SAM9260)
-
-#if defined(CONFIG_MACH_USB_A9260) || defined(CONFIG_MACH_QIL_A9260)
-#define AT91SAM9_MASTER_CLOCK 90000000
-#else
-#define AT91SAM9_MASTER_CLOCK 99300000
-#endif
-
-#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91SAM9261)
-
-#define AT91SAM9_MASTER_CLOCK 99300000
-#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91SAM9G10)
-
-#define AT91SAM9_MASTER_CLOCK 133000000
-#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91SAM9263)
-
-#if defined(CONFIG_MACH_USB_A9263)
-#define AT91SAM9_MASTER_CLOCK 90000000
-#else
-#define AT91SAM9_MASTER_CLOCK 99959500
-#endif
-
-#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91SAM9RL)
-
-#define AT91SAM9_MASTER_CLOCK 100000000
-#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91SAM9G20)
+#define AT91X40_MASTER_CLOCK 40000000
+#define CLOCK_TICK_RATE (AT91X40_MASTER_CLOCK)
-#if defined(CONFIG_MACH_USB_A9G20)
-#define AT91SAM9_MASTER_CLOCK 133000000
#else
-#define AT91SAM9_MASTER_CLOCK 132096000
-#endif
-
-#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91SAM9G45)
-#define AT91SAM9_MASTER_CLOCK 133333333
-#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91CAP9)
-
-#define AT91CAP9_MASTER_CLOCK 100000000
-#define CLOCK_TICK_RATE (AT91CAP9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91X40)
-
-#define AT91X40_MASTER_CLOCK 40000000
-#define CLOCK_TICK_RATE (AT91X40_MASTER_CLOCK)
+#define CLOCK_TICK_RATE 12345678
#endif
-#endif
+#endif /* __ASM_ARCH_TIMEX_H */
#include <linux/io.h>
#include <linux/atmel_serial.h>
-#if defined(CONFIG_AT91_EARLY_DBGU)
-#define UART_OFFSET (AT91_DBGU + AT91_BASE_SYS)
+#if defined(CONFIG_AT91_EARLY_DBGU0)
+#define UART_OFFSET AT91_BASE_DBGU0
+#elif defined(CONFIG_AT91_EARLY_DBGU1)
+#define UART_OFFSET AT91_BASE_DBGU1
#elif defined(CONFIG_AT91_EARLY_USART0)
#define UART_OFFSET AT91_USART0
#elif defined(CONFIG_AT91_EARLY_USART1)
#include <asm/mach/irq.h>
#include <asm/mach/map.h>
+void __iomem *at91_aic_base;
static void at91_aic_mask_irq(struct irq_data *d)
{
/* Disable interrupt on AIC */
- at91_sys_write(AT91_AIC_IDCR, 1 << d->irq);
+ at91_aic_write(AT91_AIC_IDCR, 1 << d->irq);
}
static void at91_aic_unmask_irq(struct irq_data *d)
{
/* Enable interrupt on AIC */
- at91_sys_write(AT91_AIC_IECR, 1 << d->irq);
+ at91_aic_write(AT91_AIC_IECR, 1 << d->irq);
}
unsigned int at91_extern_irq;
return -EINVAL;
}
- smr = at91_sys_read(AT91_AIC_SMR(d->irq)) & ~AT91_AIC_SRCTYPE;
- at91_sys_write(AT91_AIC_SMR(d->irq), smr | srctype);
+ smr = at91_aic_read(AT91_AIC_SMR(d->irq)) & ~AT91_AIC_SRCTYPE;
+ at91_aic_write(AT91_AIC_SMR(d->irq), smr | srctype);
return 0;
}
void at91_irq_suspend(void)
{
- backups = at91_sys_read(AT91_AIC_IMR);
- at91_sys_write(AT91_AIC_IDCR, backups);
- at91_sys_write(AT91_AIC_IECR, wakeups);
+ backups = at91_aic_read(AT91_AIC_IMR);
+ at91_aic_write(AT91_AIC_IDCR, backups);
+ at91_aic_write(AT91_AIC_IECR, wakeups);
}
void at91_irq_resume(void)
{
- at91_sys_write(AT91_AIC_IDCR, wakeups);
- at91_sys_write(AT91_AIC_IECR, backups);
+ at91_aic_write(AT91_AIC_IDCR, wakeups);
+ at91_aic_write(AT91_AIC_IECR, backups);
}
#else
{
unsigned int i;
+ at91_aic_base = ioremap(AT91_AIC, 512);
+
+ if (!at91_aic_base)
+ panic("Impossible to ioremap AT91_AIC\n");
+
/*
* The IVR is used by macro get_irqnr_and_base to read and verify.
* The irq number is NR_AIC_IRQS when a spurious interrupt has occurred.
*/
for (i = 0; i < NR_AIC_IRQS; i++) {
/* Put irq number in Source Vector Register: */
- at91_sys_write(AT91_AIC_SVR(i), i);
+ at91_aic_write(AT91_AIC_SVR(i), i);
/* Active Low interrupt, with the specified priority */
- at91_sys_write(AT91_AIC_SMR(i), AT91_AIC_SRCTYPE_LOW | priority[i]);
+ at91_aic_write(AT91_AIC_SMR(i), AT91_AIC_SRCTYPE_LOW | priority[i]);
irq_set_chip_and_handler(i, &at91_aic_chip, handle_level_irq);
set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
/* Perform 8 End Of Interrupt Command to make sure AIC will not Lock out nIRQ */
if (i < 8)
- at91_sys_write(AT91_AIC_EOICR, 0);
+ at91_aic_write(AT91_AIC_EOICR, 0);
}
/*
* Spurious Interrupt ID in Spurious Vector Register is NR_AIC_IRQS
* When there is no current interrupt, the IRQ Vector Register reads the value stored in AIC_SPU
*/
- at91_sys_write(AT91_AIC_SPU, NR_AIC_IRQS);
+ at91_aic_write(AT91_AIC_SPU, NR_AIC_IRQS);
/* No debugging in AIC: Debug (Protect) Control Register */
- at91_sys_write(AT91_AIC_DCR, 0);
+ at91_aic_write(AT91_AIC_DCR, 0);
/* Disable and clear all interrupts initially */
- at91_sys_write(AT91_AIC_IDCR, 0xFFFFFFFF);
- at91_sys_write(AT91_AIC_ICCR, 0xFFFFFFFF);
+ at91_aic_write(AT91_AIC_IDCR, 0xFFFFFFFF);
+ at91_aic_write(AT91_AIC_ICCR, 0xFFFFFFFF);
}
/*
* Show the reason for the previous system reset.
*/
-#if defined(AT91_SHDWC)
+#if defined(AT91_RSTC)
#include <mach/at91_rstc.h>
#include <mach/at91_shdwc.h>
char *reason, *r2 = reset;
u32 reset_type, wake_type;
+ if (!at91_shdwc_base)
+ return;
+
reset_type = at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_RSTTYP;
- wake_type = at91_sys_read(AT91_SHDW_SR);
+ wake_type = at91_shdwc_read(AT91_SHDW_SR);
switch (reset_type) {
case AT91_RSTC_RSTTYP_GENERAL:
| (1 << AT91_ID_FIQ)
| (1 << AT91_ID_SYS)
| (at91_extern_irq))
- & at91_sys_read(AT91_AIC_IMR),
+ & at91_aic_read(AT91_AIC_IMR),
state);
switch (state) {
}
pr_debug("AT91: PM - wakeup %08x\n",
- at91_sys_read(AT91_AIC_IPR) & at91_sys_read(AT91_AIC_IMR));
+ at91_aic_read(AT91_AIC_IPR) & at91_aic_read(AT91_AIC_IMR));
error:
target_state = PM_SUSPEND_ON;
#include <linux/module.h>
#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
-void __init sam9_smc_configure(int cs, struct sam9_smc_config* config)
+
+#define AT91_SMC_CS(id, n) (smc_base_addr[id] + ((n) * 0x10))
+
+static void __iomem *smc_base_addr[2];
+
+static void __init sam9_smc_cs_configure(void __iomem *base, struct sam9_smc_config* config)
{
+
/* Setup register */
- at91_sys_write(AT91_SMC_SETUP(cs),
- AT91_SMC_NWESETUP_(config->nwe_setup)
- | AT91_SMC_NCS_WRSETUP_(config->ncs_write_setup)
- | AT91_SMC_NRDSETUP_(config->nrd_setup)
- | AT91_SMC_NCS_RDSETUP_(config->ncs_read_setup)
- );
+ __raw_writel(AT91_SMC_NWESETUP_(config->nwe_setup)
+ | AT91_SMC_NCS_WRSETUP_(config->ncs_write_setup)
+ | AT91_SMC_NRDSETUP_(config->nrd_setup)
+ | AT91_SMC_NCS_RDSETUP_(config->ncs_read_setup),
+ base + AT91_SMC_SETUP);
/* Pulse register */
- at91_sys_write(AT91_SMC_PULSE(cs),
- AT91_SMC_NWEPULSE_(config->nwe_pulse)
- | AT91_SMC_NCS_WRPULSE_(config->ncs_write_pulse)
- | AT91_SMC_NRDPULSE_(config->nrd_pulse)
- | AT91_SMC_NCS_RDPULSE_(config->ncs_read_pulse)
- );
+ __raw_writel(AT91_SMC_NWEPULSE_(config->nwe_pulse)
+ | AT91_SMC_NCS_WRPULSE_(config->ncs_write_pulse)
+ | AT91_SMC_NRDPULSE_(config->nrd_pulse)
+ | AT91_SMC_NCS_RDPULSE_(config->ncs_read_pulse),
+ base + AT91_SMC_PULSE);
/* Cycle register */
- at91_sys_write(AT91_SMC_CYCLE(cs),
- AT91_SMC_NWECYCLE_(config->write_cycle)
- | AT91_SMC_NRDCYCLE_(config->read_cycle)
- );
+ __raw_writel(AT91_SMC_NWECYCLE_(config->write_cycle)
+ | AT91_SMC_NRDCYCLE_(config->read_cycle),
+ base + AT91_SMC_CYCLE);
/* Mode register */
- at91_sys_write(AT91_SMC_MODE(cs),
- config->mode
- | AT91_SMC_TDF_(config->tdf_cycles)
- );
+ __raw_writel(config->mode
+ | AT91_SMC_TDF_(config->tdf_cycles),
+ base + AT91_SMC_MODE);
+}
+
+void __init sam9_smc_configure(int id, int cs, struct sam9_smc_config* config)
+{
+ sam9_smc_cs_configure(AT91_SMC_CS(id, cs), config);
+}
+
+void __init at91sam9_ioremap_smc(int id, u32 addr)
+{
+ if (id > 1) {
+ pr_warn("%s: id > 2\n", __func__);
+ return;
+ }
+ smc_base_addr[id] = ioremap(addr, 512);
+ if (!smc_base_addr[id])
+ pr_warn("Impossible to ioremap smc.%d 0x%x\n", id, addr);
}
u8 tdf_cycles:4;
};
-extern void __init sam9_smc_configure(int cs, struct sam9_smc_config* config);
+extern void __init sam9_smc_configure(int id, int cs, struct sam9_smc_config* config);
+extern void __init at91sam9_ioremap_smc(int id, u32 addr);
#include <linux/module.h>
#include <linux/io.h>
#include <linux/mm.h>
+#include <linux/pm.h>
#include <asm/mach/map.h>
#include <mach/cpu.h>
#include <mach/at91_dbgu.h>
#include <mach/at91_pmc.h>
+#include <mach/at91_shdwc.h>
#include "soc.h"
#include "generic.h"
.type = MT_DEVICE,
};
-#define AT91_DBGU0 0xfffff200
-#define AT91_DBGU1 0xffffee00
-
static void __init soc_detect(u32 dbgu_base)
{
u32 cidr, socid;
at91_soc_initdata.type = AT91_SOC_NONE;
at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE;
- soc_detect(AT91_DBGU0);
+ soc_detect(AT91_BASE_DBGU0);
if (!at91_soc_is_detected())
- soc_detect(AT91_DBGU1);
+ soc_detect(AT91_BASE_DBGU1);
if (!at91_soc_is_detected())
panic("AT91: Impossible to detect the SOC type");
at91_boot_soc.map_io();
}
+void __iomem *at91_shdwc_base = NULL;
+
+static void at91sam9_poweroff(void)
+{
+ at91_shdwc_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
+}
+
+void __init at91_ioremap_shdwc(u32 base_addr)
+{
+ at91_shdwc_base = ioremap(base_addr, 16);
+ if (!at91_shdwc_base)
+ panic("Impossible to ioremap at91_shdwc_base\n");
+ pm_power_off = at91sam9_poweroff;
+}
+
void __init at91_initialize(unsigned long main_clock)
{
+ at91_boot_soc.ioremap_registers();
+
/* Init clock subsystem */
at91_clock_init(main_clock);
struct at91_init_soc {
unsigned int *default_irq_priority;
void (*map_io)(void);
+ void (*ioremap_registers)(void);
void (*register_clocks)(void);
void (*init)(void);
};
#include <linux/i2c.h>
#include <linux/videodev2.h>
#include <linux/davinci_emac.h>
+#include <media/davinci/vpif_types.h>
#define DM646X_EMAC_BASE (0x01C80000)
#define DM646X_EMAC_MDIO_BASE (DM646X_EMAC_BASE + 0x4000)
void dm646x_video_init(void);
-enum vpif_if_type {
- VPIF_IF_BT656,
- VPIF_IF_BT1120,
- VPIF_IF_RAW_BAYER
-};
-
-struct vpif_interface {
- enum vpif_if_type if_type;
- unsigned hd_pol:1;
- unsigned vd_pol:1;
- unsigned fid_pol:1;
-};
-
-struct vpif_subdev_info {
- const char *name;
- struct i2c_board_info board_info;
- u32 input;
- u32 output;
- unsigned can_route:1;
- struct vpif_interface vpif_if;
-};
-
-struct vpif_display_config {
- int (*set_clock)(int, int);
- struct vpif_subdev_info *subdevinfo;
- int subdev_count;
- const char **output;
- int output_count;
- const char *card_name;
-};
-
-struct vpif_input {
- struct v4l2_input input;
- const char *subdev_name;
-};
-
-#define VPIF_CAPTURE_MAX_CHANNELS 2
-
-struct vpif_capture_chan_config {
- const struct vpif_input *inputs;
- int input_count;
-};
-
-struct vpif_capture_config {
- int (*setup_input_channel_mode)(int);
- int (*setup_input_path)(int, const char *);
- struct vpif_capture_chan_config chan_config[VPIF_CAPTURE_MAX_CHANNELS];
- struct vpif_subdev_info *subdev_info;
- int subdev_count;
- const char *card_name;
-};
-
void dm646x_setup_vpif(struct vpif_display_config *,
struct vpif_capture_config *);
select CPU_V6
select GPIO_MSM_V1
select MSM_PROC_COMM
- select HAS_MSM_DEBUG_UART_PHYS
config ARCH_MSM7X30
bool "MSM7x30"
select MSM_GPIOMUX
select GPIO_MSM_V1
select MSM_PROC_COMM
- select HAS_MSM_DEBUG_UART_PHYS
config ARCH_QSD8X50
bool "QSD8X50"
select MSM_GPIOMUX
select GPIO_MSM_V1
select MSM_PROC_COMM
- select HAS_MSM_DEBUG_UART_PHYS
config ARCH_MSM8X60
bool "MSM8X60"
endchoice
+config MSM_HAS_DEBUG_UART_HS
+ bool
+
config MSM_SOC_REV_A
bool
config ARCH_MSM_SCORPIONMP
config ARCH_MSM_SCORPION
bool
-config HAS_MSM_DEBUG_UART_PHYS
- bool
-
config MSM_VIC
bool
endmenu
-config MSM_DEBUG_UART
- int
- default 1 if MSM_DEBUG_UART1
- default 2 if MSM_DEBUG_UART2
- default 3 if MSM_DEBUG_UART3
-
-if HAS_MSM_DEBUG_UART_PHYS
-choice
- prompt "Debug UART"
-
- default MSM_DEBUG_UART_NONE
-
- config MSM_DEBUG_UART_NONE
- bool "None"
-
- config MSM_DEBUG_UART1
- bool "UART1"
-
- config MSM_DEBUG_UART2
- bool "UART2"
-
- config MSM_DEBUG_UART3
- bool "UART3"
-endchoice
-endif
-
config MSM_SMD_PKG3
bool
-/* arch/arm/mach-msm7200/include/mach/debug-macro.S
+/*
*
* Copyright (C) 2007 Google, Inc.
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
* Author: Brian Swetland <swetland@google.com>
*
* This software is licensed under the terms of the GNU General Public
*
*/
-
-
#include <mach/hardware.h>
#include <mach/msm_iomap.h>
-#if defined(CONFIG_HAS_MSM_DEBUG_UART_PHYS) && !defined(CONFIG_MSM_DEBUG_UART_NONE)
.macro addruart, rp, rv, tmp
+#ifdef MSM_DEBUG_UART_PHYS
ldr \rp, =MSM_DEBUG_UART_PHYS
ldr \rv, =MSM_DEBUG_UART_BASE
+#endif
.endm
- .macro senduart,rd,rx
+ .macro senduart, rd, rx
+#ifdef CONFIG_MSM_HAS_DEBUG_UART_HS
+ @ Write the 1 character to UARTDM_TF
+ str \rd, [\rx, #0x70]
+#else
teq \rx, #0
strne \rd, [\rx, #0x0C]
+#endif
.endm
- .macro waituart,rd,rx
+ .macro waituart, rd, rx
+#ifdef CONFIG_MSM_HAS_DEBUG_UART_HS
+ @ check for TX_EMT in UARTDM_SR
+ ldr \rd, [\rx, #0x08]
+ tst \rd, #0x08
+ bne 1002f
+ @ wait for TXREADY in UARTDM_ISR
+1001: ldr \rd, [\rx, #0x14]
+ tst \rd, #0x80
+ beq 1001b
+1002:
+ @ Clear TX_READY by writing to the UARTDM_CR register
+ mov \rd, #0x300
+ str \rd, [\rx, #0x10]
+ @ Write 0x1 to NCF register
+ mov \rd, #0x1
+ str \rd, [\rx, #0x40]
+ @ UARTDM reg. Read to induce delay
+ ldr \rd, [\rx, #0x08]
+#else
@ wait for TX_READY
1001: ldr \rd, [\rx, #0x08]
tst \rd, #0x04
beq 1001b
- .endm
-#else
- .macro addruart, rp, rv, tmp
- mov \rv, #0xff000000
- orr \rv, \rv, #0x00f00000
- .endm
-
- .macro senduart,rd,rx
- .endm
-
- .macro waituart,rd,rx
- .endm
#endif
+ .endm
- .macro busyuart,rd,rx
+ .macro busyuart, rd, rx
.endm
#define MSM_UART3_PHYS 0xA9C00000
#define MSM_UART3_SIZE SZ_4K
-#ifdef CONFIG_MSM_DEBUG_UART
-#define MSM_DEBUG_UART_BASE 0xE1000000
-#if CONFIG_MSM_DEBUG_UART == 1
-#define MSM_DEBUG_UART_PHYS MSM_UART1_PHYS
-#elif CONFIG_MSM_DEBUG_UART == 2
-#define MSM_DEBUG_UART_PHYS MSM_UART2_PHYS
-#elif CONFIG_MSM_DEBUG_UART == 3
-#define MSM_DEBUG_UART_PHYS MSM_UART3_PHYS
-#endif
-#define MSM_DEBUG_UART_SIZE SZ_4K
-#endif
-
#define MSM_SDC1_PHYS 0xA0400000
#define MSM_SDC1_SIZE SZ_4K
#define MSM_UART3_PHYS 0xACC00000
#define MSM_UART3_SIZE SZ_4K
-#ifdef CONFIG_MSM_DEBUG_UART
-#define MSM_DEBUG_UART_BASE 0xE1000000
-#if CONFIG_MSM_DEBUG_UART == 1
-#define MSM_DEBUG_UART_PHYS MSM_UART1_PHYS
-#elif CONFIG_MSM_DEBUG_UART == 2
-#define MSM_DEBUG_UART_PHYS MSM_UART2_PHYS
-#elif CONFIG_MSM_DEBUG_UART == 3
-#define MSM_DEBUG_UART_PHYS MSM_UART3_PHYS
-#endif
-#define MSM_DEBUG_UART_SIZE SZ_4K
-#endif
-
#define MSM_MDC_BASE IOMEM(0xE0200000)
#define MSM_MDC_PHYS 0xAA500000
#define MSM_MDC_SIZE SZ_1M
#define MSM8960_TMR0_PHYS 0x0208A000
#define MSM8960_TMR0_SIZE SZ_4K
+#ifdef CONFIG_DEBUG_MSM8960_UART
+#define MSM_DEBUG_UART_BASE 0xE1040000
+#define MSM_DEBUG_UART_PHYS 0x16440000
+#endif
+
#endif
#define MSM_UART3_PHYS 0xA9C00000
#define MSM_UART3_SIZE SZ_4K
-#ifdef CONFIG_MSM_DEBUG_UART
-#define MSM_DEBUG_UART_BASE 0xE1000000
-#if CONFIG_MSM_DEBUG_UART == 1
-#define MSM_DEBUG_UART_PHYS MSM_UART1_PHYS
-#elif CONFIG_MSM_DEBUG_UART == 2
-#define MSM_DEBUG_UART_PHYS MSM_UART2_PHYS
-#elif CONFIG_MSM_DEBUG_UART == 3
-#define MSM_DEBUG_UART_PHYS MSM_UART3_PHYS
-#endif
-#define MSM_DEBUG_UART_SIZE SZ_4K
-#endif
-
#define MSM_MDC_BASE IOMEM(0xE0200000)
#define MSM_MDC_PHYS 0xAA500000
#define MSM_MDC_SIZE SZ_1M
#define MSM8X60_TMR0_PHYS 0x02040000
#define MSM8X60_TMR0_SIZE SZ_4K
+#ifdef CONFIG_DEBUG_MSM8660_UART
+#define MSM_DEBUG_UART_BASE 0xE1040000
+#define MSM_DEBUG_UART_PHYS 0x19C40000
+#endif
+
#endif
#include "msm_iomap-8960.h"
+#define MSM_DEBUG_UART_SIZE SZ_4K
+#if defined(CONFIG_DEBUG_MSM_UART1)
+#define MSM_DEBUG_UART_BASE 0xE1000000
+#define MSM_DEBUG_UART_PHYS MSM_UART1_PHYS
+#elif defined(CONFIG_DEBUG_MSM_UART2)
+#define MSM_DEBUG_UART_BASE 0xE1000000
+#define MSM_DEBUG_UART_PHYS MSM_UART2_PHYS
+#elif defined(CONFIG_DEBUG_MSM_UART3)
+#define MSM_DEBUG_UART_BASE 0xE1000000
+#define MSM_DEBUG_UART_PHYS MSM_UART3_PHYS
+#endif
+
/* Virtual addresses shared across all MSM targets. */
#define MSM_CSR_BASE IOMEM(0xE0001000)
#define MSM_QGIC_DIST_BASE IOMEM(0xF0000000)
-/* arch/arm/mach-msm/include/mach/uncompress.h
- *
+/*
* Copyright (C) 2007 Google, Inc.
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
*
* This software is licensed under the terms of the GNU General Public
* License version 2, as published by the Free Software Foundation, and
*/
#ifndef __ASM_ARCH_MSM_UNCOMPRESS_H
+#define __ASM_ARCH_MSM_UNCOMPRESS_H
+
+#include <asm/processor.h>
+#include <mach/msm_iomap.h>
+
+#define UART_CSR (*(volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x08))
+#define UART_TF (*(volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x0c))
-#include "hardware.h"
-#include "linux/io.h"
-#include "mach/msm_iomap.h"
+#define UART_DM_SR (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x08)))
+#define UART_DM_CR (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x10)))
+#define UART_DM_ISR (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x14)))
+#define UART_DM_NCHAR (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x40)))
+#define UART_DM_TF (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x70)))
static void putc(int c)
{
#if defined(MSM_DEBUG_UART_PHYS)
- unsigned base = MSM_DEBUG_UART_PHYS;
- while (!(readl(base + 0x08) & 0x04)) ;
- writel(c, base + 0x0c);
+#ifdef CONFIG_MSM_HAS_DEBUG_UART_HS
+ /*
+ * Wait for TX_READY to be set; but skip it if we have a
+ * TX underrun.
+ */
+ if (UART_DM_SR & 0x08)
+ while (!(UART_DM_ISR & 0x80))
+ cpu_relax();
+
+ UART_DM_CR = 0x300;
+ UART_DM_NCHAR = 0x1;
+ UART_DM_TF = c;
+#else
+ while (!(UART_CSR & 0x04))
+ cpu_relax();
+ UART_TF = c;
+#endif
#endif
}
MSM_CHIP_DEVICE(GPIO1, MSM7X00),
MSM_CHIP_DEVICE(GPIO2, MSM7X00),
MSM_DEVICE(CLK_CTL),
-#ifdef CONFIG_MSM_DEBUG_UART
+#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \
+ defined(CONFIG_DEBUG_MSM_UART3)
MSM_DEVICE(DEBUG_UART),
#endif
#ifdef CONFIG_ARCH_MSM7X30
MSM_DEVICE(SCPLL),
MSM_DEVICE(AD5),
MSM_DEVICE(MDC),
-#ifdef CONFIG_MSM_DEBUG_UART
+#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \
+ defined(CONFIG_DEBUG_MSM_UART3)
MSM_DEVICE(DEBUG_UART),
#endif
{
MSM_CHIP_DEVICE(TMR0, MSM8X60),
MSM_DEVICE(ACC),
MSM_DEVICE(GCC),
+#ifdef CONFIG_DEBUG_MSM8660_UART
+ MSM_DEVICE(DEBUG_UART),
+#endif
};
void __init msm_map_msm8x60_io(void)
MSM_CHIP_DEVICE(QGIC_CPU, MSM8960),
MSM_CHIP_DEVICE(TMR, MSM8960),
MSM_CHIP_DEVICE(TMR0, MSM8960),
+#ifdef CONFIG_DEBUG_MSM8960_UART
+ MSM_DEVICE(DEBUG_UART),
+#endif
};
void __init msm_map_msm8960_io(void)
MSM_DEVICE(SAW),
MSM_DEVICE(GCC),
MSM_DEVICE(TCSR),
-#ifdef CONFIG_MSM_DEBUG_UART
+#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \
+ defined(CONFIG_DEBUG_MSM_UART3)
MSM_DEVICE(DEBUG_UART),
#endif
{
ret = scm_set_boot_addr(virt_to_phys(msm_secondary_startup),
SCM_FLAG_COLDBOOT_CPU1);
if (ret == 0) {
- void *sc1_base_ptr;
+ void __iomem *sc1_base_ptr;
sc1_base_ptr = ioremap_nocache(0x00902000, SZ_4K*2);
if (sc1_base_ptr) {
writel(0, sc1_base_ptr + VDD_SC1_ARRAY_CLAMP_GFS_CTL);
obj-y := common.o
obj-y += time.o
-obj-y += io.o
#include <asm/mach/arch.h>
#include <asm/hardware/vic.h>
+#include <asm/mach/map.h>
#include <mach/map.h>
#include <mach/picoxcell_soc.h>
#include "common.h"
+static struct map_desc io_map __initdata = {
+ .virtual = PHYS_TO_IO(PICOXCELL_PERIPH_BASE),
+ .pfn = __phys_to_pfn(PICOXCELL_PERIPH_BASE),
+ .length = PICOXCELL_PERIPH_LENGTH,
+ .type = MT_DEVICE,
+};
+
+static void __init picoxcell_map_io(void)
+{
+ iotable_init(&io_map, 1);
+}
+
static void __init picoxcell_init_machine(void)
{
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
DT_MACHINE_START(PICOXCELL, "Picochip picoXcell")
.map_io = picoxcell_map_io,
- .nr_irqs = ARCH_NR_IRQS,
+ .nr_irqs = NR_IRQS_LEGACY,
.init_irq = picoxcell_init_irq,
.handle_irq = vic_handle_irq,
.timer = &picoxcell_timer,
#include <asm/mach/time.h>
extern struct sys_timer picoxcell_timer;
-extern void picoxcell_map_io(void);
#endif /* __PICOXCELL_COMMON_H__ */
/*
* Copyright (c) 2011 Picochip Ltd., Jamie Iles
*
- * This file contains the hardware definitions of the picoXcell SoC devices.
- *
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
#ifndef __MACH_IRQS_H
#define __MACH_IRQS_H
-#define ARCH_NR_IRQS 64
-#define NR_IRQS (128 + ARCH_NR_IRQS)
-
-#define IRQ_VIC0_BASE 0
-#define IRQ_VIC1_BASE 32
+/* We dynamically allocate our irq_desc's. */
+#define NR_IRQS 0
#endif /* __MACH_IRQS_H */
+++ /dev/null
-/* empty */
+++ /dev/null
-/*
- * Copyright (c) 2011 Picochip Ltd., Jamie Iles
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * All enquiries to support@picochip.com
- */
-#include <linux/io.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/of.h>
-
-#include <asm/mach/map.h>
-
-#include <mach/map.h>
-#include <mach/picoxcell_soc.h>
-
-#include "common.h"
-
-void __init picoxcell_map_io(void)
-{
- struct map_desc io_map = {
- .virtual = PHYS_TO_IO(PICOXCELL_PERIPH_BASE),
- .pfn = __phys_to_pfn(PICOXCELL_PERIPH_BASE),
- .length = PICOXCELL_PERIPH_LENGTH,
- .type = MT_DEVICE,
- };
-
- iotable_init(&io_map, 1);
-}
obj-$(CONFIG_TEGRA_PCI) += pcie.o
obj-$(CONFIG_USB_SUPPORT) += usb_phy.o
-obj-${CONFIG_MACH_HARMONY} += board-harmony.o
-obj-${CONFIG_MACH_HARMONY} += board-harmony-pinmux.o
-obj-${CONFIG_MACH_HARMONY} += board-harmony-pcie.o
-obj-${CONFIG_MACH_HARMONY} += board-harmony-power.o
+obj-$(CONFIG_MACH_HARMONY) += board-harmony.o
+obj-$(CONFIG_MACH_HARMONY) += board-harmony-pinmux.o
+obj-$(CONFIG_MACH_HARMONY) += board-harmony-pcie.o
+obj-$(CONFIG_MACH_HARMONY) += board-harmony-power.o
-obj-${CONFIG_MACH_PAZ00} += board-paz00.o
-obj-${CONFIG_MACH_PAZ00} += board-paz00-pinmux.o
+obj-$(CONFIG_MACH_PAZ00) += board-paz00.o
+obj-$(CONFIG_MACH_PAZ00) += board-paz00-pinmux.o
-obj-${CONFIG_MACH_SEABOARD} += board-seaboard.o
-obj-${CONFIG_MACH_SEABOARD} += board-seaboard-pinmux.o
+obj-$(CONFIG_MACH_SEABOARD) += board-seaboard.o
+obj-$(CONFIG_MACH_SEABOARD) += board-seaboard-pinmux.o
-obj-${CONFIG_MACH_TEGRA_DT} += board-dt.o
-obj-${CONFIG_MACH_TEGRA_DT} += board-harmony-pinmux.o
-obj-${CONFIG_MACH_TEGRA_DT} += board-seaboard-pinmux.o
+obj-$(CONFIG_MACH_TEGRA_DT) += board-dt.o
+obj-$(CONFIG_MACH_TEGRA_DT) += board-harmony-pinmux.o
+obj-$(CONFIG_MACH_TEGRA_DT) += board-seaboard-pinmux.o
-obj-${CONFIG_MACH_TRIMSLICE} += board-trimslice.o
-obj-${CONFIG_MACH_TRIMSLICE} += board-trimslice-pinmux.o
+obj-$(CONFIG_MACH_TRIMSLICE) += board-trimslice.o
+obj-$(CONFIG_MACH_TRIMSLICE) += board-trimslice-pinmux.o
.macro arch_ret_to_user, tmp1, tmp2
.endm
-
-#if !defined(CONFIG_ARM_GIC)
- /* legacy interrupt controller for AP16 */
-
- .macro get_irqnr_preamble, base, tmp
- @ enable imprecise aborts
- cpsie a
- @ EVP base at 0xf010f000
- mov \base, #0xf0000000
- orr \base, #0x00100000
- orr \base, #0x0000f000
- .endm
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
- ldr \irqnr, [\base, #0x20] @ EVT_IRQ_STS
- cmp \irqnr, #0x80
- .endm
-#endif
#include "board.h"
-#define INT_SYS_NR (INT_GPIO_BASE - INT_PRI_BASE)
-#define INT_SYS_SZ (INT_SEC_BASE - INT_PRI_BASE)
-#define PPI_NR ((INT_SYS_NR+INT_SYS_SZ-1)/INT_SYS_SZ)
-
#define ICTLR_CPU_IEP_VFIQ 0x08
#define ICTLR_CPU_IEP_FIR 0x14
#define ICTLR_CPU_IEP_FIR_SET 0x18
+++ /dev/null
-/*
- *
- * arch/arm/mach-u300/include/mach/memory.h
- *
- *
- * Copyright (C) 2007-2009 ST-Ericsson AB
- * License terms: GNU General Public License (GPL) version 2
- * Memory virtual/physical mapping constants.
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- * Author: Jonas Aaberg <jonas.aberg@stericsson.com>
- */
-
-#ifndef __MACH_MEMORY_H
-#define __MACH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET UL(0x48000000)
-#define BOOT_PARAMS_OFFSET 0x100
-
-#endif
MACHINE_START(U300, MACH_U300_STRING)
/* Maintainer: Linus Walleij <linus.walleij@stericsson.com> */
- .atag_offset = BOOT_PARAMS_OFFSET,
+ .atag_offset = 0x100,
.map_io = u300_map_io,
.init_irq = u300_init_irq,
.handle_irq = vic_handle_irq,
u8 addr[6];
};
static struct eth_addr __initdata hw_addr[2];
-static struct eth_platform_data __initdata eth_data[2];
+static struct macb_platform_data __initdata eth_data[2];
static struct spi_board_info spi0_board_info[] __initdata = {
{
};
static struct eth_addr __initdata hw_addr[2];
-static struct eth_platform_data __initdata eth_data[2] = {
+static struct macb_platform_data __initdata eth_data[2] = {
{
/*
* The MDIO pullups on STK1000 are a bit too weak for
u8 addr[6];
};
static struct eth_addr __initdata hw_addr[1];
-static struct eth_platform_data __initdata eth_data[1] = {
+static struct macb_platform_data __initdata eth_data[1] = {
{
.phy_mask = ~(1U << 1),
},
};
static struct eth_addr __initdata hw_addr[1];
-static struct eth_platform_data __initdata eth_data[1];
+static struct macb_platform_data __initdata eth_data[1];
/*
* The next two functions should go away as the boot loader is
};
static struct eth_addr __initdata hw_addr[2];
-static struct eth_platform_data __initdata eth_data[2];
+static struct macb_platform_data __initdata eth_data[2];
static int ads7846_get_pendown_state_PB26(void)
{
u8 addr[6];
};
static struct eth_addr __initdata hw_addr[2];
-static struct eth_platform_data __initdata eth_data[2];
+static struct macb_platform_data __initdata eth_data[2];
static struct spi_eeprom eeprom_25lc010 = {
.name = "25lc010",
* -------------------------------------------------------------------- */
#ifdef CONFIG_CPU_AT32AP7000
-static struct eth_platform_data macb0_data;
+static struct macb_platform_data macb0_data;
static struct resource macb0_resource[] = {
PBMEM(0xfff01800),
IRQ(25),
DEV_CLK(hclk, macb0, hsb, 8);
DEV_CLK(pclk, macb0, pbb, 6);
-static struct eth_platform_data macb1_data;
+static struct macb_platform_data macb1_data;
static struct resource macb1_resource[] = {
PBMEM(0xfff01c00),
IRQ(26),
DEV_CLK(pclk, macb1, pbb, 7);
struct platform_device *__init
-at32_add_device_eth(unsigned int id, struct eth_platform_data *data)
+at32_add_device_eth(unsigned int id, struct macb_platform_data *data)
{
struct platform_device *pdev;
u32 pin_mask;
return NULL;
}
- memcpy(pdev->dev.platform_data, data, sizeof(struct eth_platform_data));
+ memcpy(pdev->dev.platform_data, data, sizeof(struct macb_platform_data));
platform_device_register(pdev);
return pdev;
#include <linux/types.h>
#include <linux/serial.h>
+#include <linux/platform_data/macb.h>
#define GPIO_PIN_NONE (-1)
void at32_map_usart(unsigned int hw_id, unsigned int line, int flags);
struct platform_device *at32_add_device_usart(unsigned int id);
-struct eth_platform_data {
- u32 phy_mask;
- u8 is_rmii;
-};
struct platform_device *
-at32_add_device_eth(unsigned int id, struct eth_platform_data *data);
+at32_add_device_eth(unsigned int id, struct macb_platform_data *data);
struct spi_board_info;
struct platform_device *
ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->pio_mask = ATA_PIO4;
- if (!irq) {
+ if (!gpio_is_valid(irq)) {
ap->flags |= ATA_FLAG_PIO_POLLING;
ata_port_desc(ap, "no IRQ, using PIO polling");
}
host->private_data = info;
- ret = ata_host_activate(host, irq ? gpio_to_irq(irq) : 0,
- irq ? ata_sff_interrupt : NULL,
+ return ata_host_activate(host, gpio_is_valid(irq) ? gpio_to_irq(irq) : 0,
+ gpio_is_valid(irq) ? ata_sff_interrupt : NULL,
irq_flags, &pata_at91_sht);
if (!ret)
apply_timings(board->chipselect, 0, ide_timing_find_mode(XFER_PIO_0), 0);
/* with GPIO interrupt we have to do quirks in handler */
- if (board->irq_pin >= PIN_BASE)
+ if (gpio_is_valid(board->irq_pin))
host->irq_handler = at91_irq_handler;
host->ports[0]->select_data = board->chipselect;
#include <linux/videodev2.h>
#include <mach/hardware.h>
#include <mach/dm646x.h>
+#include <media/davinci/vpif_types.h>
/* Maximum channel allowed */
#define VPIF_NUM_CHANNELS (4)
#include <media/v4l2-device.h>
#include <media/videobuf-core.h>
#include <media/videobuf-dma-contig.h>
-#include <mach/dm646x.h>
+#include <media/davinci/vpif_types.h>
#include "vpif.h"
#include <media/v4l2-device.h>
#include <media/videobuf-core.h>
#include <media/videobuf-dma-contig.h>
+#include <media/davinci/vpif_types.h>
#include "vpif.h"
at91_mci_write(host, AT91_MCI_MR, (at91_mci_read(host, AT91_MCI_MR) & ~AT91_MCI_CLKDIV) | clkdiv);
/* maybe switch power to the card */
- if (host->board->vcc_pin) {
+ if (gpio_is_valid(host->board->vcc_pin)) {
switch (ios->power_mode) {
case MMC_POWER_OFF:
gpio_set_value(host->board->vcc_pin, 0);
{
struct at91mci_host *host = mmc_priv(mmc);
- if (host->board->wp_pin)
+ if (gpio_is_valid(host->board->wp_pin))
return !!gpio_get_value(host->board->wp_pin);
/*
* Board doesn't support read only detection; let the mmc core
* Reserve GPIOs ... board init code makes sure these pins are set
* up as GPIOs with the right direction (input, except for vcc)
*/
- if (host->board->det_pin) {
+ if (gpio_is_valid(host->board->det_pin)) {
ret = gpio_request(host->board->det_pin, "mmc_detect");
if (ret < 0) {
dev_dbg(&pdev->dev, "couldn't claim card detect pin\n");
goto fail4b;
}
}
- if (host->board->wp_pin) {
+ if (gpio_is_valid(host->board->wp_pin)) {
ret = gpio_request(host->board->wp_pin, "mmc_wp");
if (ret < 0) {
dev_dbg(&pdev->dev, "couldn't claim wp sense pin\n");
goto fail4;
}
}
- if (host->board->vcc_pin) {
+ if (gpio_is_valid(host->board->vcc_pin)) {
ret = gpio_request(host->board->vcc_pin, "mmc_vcc");
if (ret < 0) {
dev_dbg(&pdev->dev, "couldn't claim vcc switch pin\n");
/*
* Add host to MMC layer
*/
- if (host->board->det_pin) {
+ if (gpio_is_valid(host->board->det_pin)) {
host->present = !gpio_get_value(host->board->det_pin);
}
else
/*
* monitor card insertion/removal if we can
*/
- if (host->board->det_pin) {
+ if (gpio_is_valid(host->board->det_pin)) {
ret = request_irq(gpio_to_irq(host->board->det_pin),
at91_mmc_det_irq, 0, mmc_hostname(mmc), host);
if (ret)
fail1:
clk_put(host->mci_clk);
fail2:
- if (host->board->vcc_pin)
+ if (gpio_is_valid(host->board->vcc_pin))
gpio_free(host->board->vcc_pin);
fail3:
- if (host->board->wp_pin)
+ if (gpio_is_valid(host->board->wp_pin))
gpio_free(host->board->wp_pin);
fail4:
- if (host->board->det_pin)
+ if (gpio_is_valid(host->board->det_pin))
gpio_free(host->board->det_pin);
fail4b:
if (host->buffer)
dma_free_coherent(&pdev->dev, MCI_BUFSIZE,
host->buffer, host->physical_address);
- if (host->board->det_pin) {
+ if (gpio_is_valid(host->board->det_pin)) {
if (device_can_wakeup(&pdev->dev))
free_irq(gpio_to_irq(host->board->det_pin), host);
device_init_wakeup(&pdev->dev, 0);
clk_disable(host->mci_clk); /* Disable the peripheral clock */
clk_put(host->mci_clk);
- if (host->board->vcc_pin)
+ if (gpio_is_valid(host->board->vcc_pin))
gpio_free(host->board->vcc_pin);
- if (host->board->wp_pin)
+ if (gpio_is_valid(host->board->wp_pin))
gpio_free(host->board->wp_pin);
iounmap(host->baseaddr);
struct at91mci_host *host = mmc_priv(mmc);
int ret = 0;
- if (host->board->det_pin && device_may_wakeup(&pdev->dev))
+ if (gpio_is_valid(host->board->det_pin) && device_may_wakeup(&pdev->dev))
enable_irq_wake(host->board->det_pin);
if (mmc)
struct at91mci_host *host = mmc_priv(mmc);
int ret = 0;
- if (host->board->det_pin && device_may_wakeup(&pdev->dev))
+ if (gpio_is_valid(host->board->det_pin) && device_may_wakeup(&pdev->dev))
disable_irq_wake(host->board->det_pin);
if (mmc)
*/
static void atmel_nand_enable(struct atmel_nand_host *host)
{
- if (host->board->enable_pin)
+ if (gpio_is_valid(host->board->enable_pin))
gpio_set_value(host->board->enable_pin, 0);
}
*/
static void atmel_nand_disable(struct atmel_nand_host *host)
{
- if (host->board->enable_pin)
+ if (gpio_is_valid(host->board->enable_pin))
gpio_set_value(host->board->enable_pin, 1);
}
nand_chip->IO_ADDR_W = host->io_base;
nand_chip->cmd_ctrl = atmel_nand_cmd_ctrl;
- if (host->board->rdy_pin)
+ if (gpio_is_valid(host->board->rdy_pin))
nand_chip->dev_ready = atmel_nand_device_ready;
regs = platform_get_resource(pdev, IORESOURCE_MEM, 1);
platform_set_drvdata(pdev, host);
atmel_nand_enable(host);
- if (host->board->det_pin) {
+ if (gpio_is_valid(host->board->det_pin)) {
if (gpio_get_value(host->board->det_pin)) {
printk(KERN_INFO "No SmartMedia card inserted.\n");
res = -ENXIO;
#include <linux/skbuff.h>
#include <linux/dma-mapping.h>
#include <linux/ethtool.h>
+#include <linux/platform_data/macb.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/gfp.h>
static int __init at91ether_setup(unsigned long phy_type, unsigned short phy_address,
struct platform_device *pdev, struct clk *ether_clk)
{
- struct at91_eth_data *board_data = pdev->dev.platform_data;
+ struct macb_platform_data *board_data = pdev->dev.platform_data;
struct net_device *dev;
struct at91_private *lp;
unsigned int val;
struct at91_private
{
struct mii_if_info mii; /* ethtool support */
- struct at91_eth_data board_data; /* board-specific configuration */
+ struct macb_platform_data board_data; /* board-specific
+ * configuration (shared with
+ * macb for common data */
struct clk *ether_clk; /* clock */
/* PHY */
* published by the Free Software Foundation.
*/
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/clk.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/dma-mapping.h>
+#include <linux/platform_data/macb.h>
#include <linux/platform_device.h>
#include <linux/phy.h>
-#include <mach/board.h>
-#include <mach/cpu.h>
-
#include "macb.h"
#define RX_BUFFER_SIZE 128
if (is_valid_ether_addr(addr)) {
memcpy(bp->dev->dev_addr, addr, sizeof(addr));
} else {
- dev_info(&bp->pdev->dev, "invalid hw address, using random\n");
+ netdev_info(bp->dev, "invalid hw address, using random\n");
random_ether_addr(bp->dev->dev_addr);
}
}
if (status_change) {
if (phydev->link)
- printk(KERN_INFO "%s: link up (%d/%s)\n",
- dev->name, phydev->speed,
- DUPLEX_FULL == phydev->duplex ? "Full":"Half");
+ netdev_info(dev, "link up (%d/%s)\n",
+ phydev->speed,
+ phydev->duplex == DUPLEX_FULL ?
+ "Full" : "Half");
else
- printk(KERN_INFO "%s: link down\n", dev->name);
+ netdev_info(dev, "link down\n");
}
}
{
struct macb *bp = netdev_priv(dev);
struct phy_device *phydev;
- struct eth_platform_data *pdata;
+ struct macb_platform_data *pdata;
int ret;
phydev = phy_find_first(bp->mii_bus);
if (!phydev) {
- printk (KERN_ERR "%s: no PHY found\n", dev->name);
+ netdev_err(dev, "no PHY found\n");
return -1;
}
PHY_INTERFACE_MODE_RMII :
PHY_INTERFACE_MODE_MII);
if (ret) {
- printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
+ netdev_err(dev, "Could not attach to PHY\n");
return ret;
}
static int macb_mii_init(struct macb *bp)
{
- struct eth_platform_data *pdata;
+ struct macb_platform_data *pdata;
int err = -ENXIO, i;
/* Enable management port */
status = macb_readl(bp, TSR);
macb_writel(bp, TSR, status);
- dev_dbg(&bp->pdev->dev, "macb_tx status = %02lx\n",
- (unsigned long)status);
+ netdev_dbg(bp->dev, "macb_tx status = %02lx\n", (unsigned long)status);
if (status & (MACB_BIT(UND) | MACB_BIT(TSR_RLE))) {
int i;
- printk(KERN_ERR "%s: TX %s, resetting buffers\n",
- bp->dev->name, status & MACB_BIT(UND) ?
- "underrun" : "retry limit exceeded");
+ netdev_err(bp->dev, "TX %s, resetting buffers\n",
+ status & MACB_BIT(UND) ?
+ "underrun" : "retry limit exceeded");
/* Transfer ongoing, disable transmitter, to avoid confusion */
if (status & MACB_BIT(TGO))
if (!(bufstat & MACB_BIT(TX_USED)))
break;
- dev_dbg(&bp->pdev->dev, "skb %u (data %p) TX complete\n",
- tail, skb->data);
+ netdev_dbg(bp->dev, "skb %u (data %p) TX complete\n",
+ tail, skb->data);
dma_unmap_single(&bp->pdev->dev, rp->mapping, skb->len,
DMA_TO_DEVICE);
bp->stats.tx_packets++;
len = MACB_BFEXT(RX_FRMLEN, bp->rx_ring[last_frag].ctrl);
- dev_dbg(&bp->pdev->dev, "macb_rx_frame frags %u - %u (len %u)\n",
- first_frag, last_frag, len);
+ netdev_dbg(bp->dev, "macb_rx_frame frags %u - %u (len %u)\n",
+ first_frag, last_frag, len);
skb = dev_alloc_skb(len + RX_OFFSET);
if (!skb) {
bp->stats.rx_packets++;
bp->stats.rx_bytes += len;
- dev_dbg(&bp->pdev->dev, "received skb of length %u, csum: %08x\n",
- skb->len, skb->csum);
+ netdev_dbg(bp->dev, "received skb of length %u, csum: %08x\n",
+ skb->len, skb->csum);
netif_receive_skb(skb);
return 0;
work_done = 0;
- dev_dbg(&bp->pdev->dev, "poll: status = %08lx, budget = %d\n",
- (unsigned long)status, budget);
+ netdev_dbg(bp->dev, "poll: status = %08lx, budget = %d\n",
+ (unsigned long)status, budget);
work_done = macb_rx(bp, budget);
if (work_done < budget) {
macb_writel(bp, IDR, MACB_RX_INT_FLAGS);
if (napi_schedule_prep(&bp->napi)) {
- dev_dbg(&bp->pdev->dev,
- "scheduling RX softirq\n");
+ netdev_dbg(bp->dev, "scheduling RX softirq\n");
__napi_schedule(&bp->napi);
}
}
if (status & MACB_BIT(HRESP)) {
/*
- * TODO: Reset the hardware, and maybe move the printk
- * to a lower-priority context as well (work queue?)
+ * TODO: Reset the hardware, and maybe move the
+ * netdev_err to a lower-priority context as well
+ * (work queue?)
*/
- printk(KERN_ERR "%s: DMA bus error: HRESP not OK\n",
- dev->name);
+ netdev_err(dev, "DMA bus error: HRESP not OK\n");
}
status = macb_readl(bp, ISR);
unsigned long flags;
#ifdef DEBUG
- int i;
- dev_dbg(&bp->pdev->dev,
- "start_xmit: len %u head %p data %p tail %p end %p\n",
- skb->len, skb->head, skb->data,
- skb_tail_pointer(skb), skb_end_pointer(skb));
- dev_dbg(&bp->pdev->dev,
- "data:");
- for (i = 0; i < 16; i++)
- printk(" %02x", (unsigned int)skb->data[i]);
- printk("\n");
+ netdev_dbg(bp->dev,
+ "start_xmit: len %u head %p data %p tail %p end %p\n",
+ skb->len, skb->head, skb->data,
+ skb_tail_pointer(skb), skb_end_pointer(skb));
+ print_hex_dump(KERN_DEBUG, "data: ", DUMP_PREFIX_OFFSET, 16, 1,
+ skb->data, 16, true);
#endif
len = skb->len;
if (TX_BUFFS_AVAIL(bp) < 1) {
netif_stop_queue(dev);
spin_unlock_irqrestore(&bp->lock, flags);
- dev_err(&bp->pdev->dev,
- "BUG! Tx Ring full when queue awake!\n");
- dev_dbg(&bp->pdev->dev, "tx_head = %u, tx_tail = %u\n",
- bp->tx_head, bp->tx_tail);
+ netdev_err(bp->dev, "BUG! Tx Ring full when queue awake!\n");
+ netdev_dbg(bp->dev, "tx_head = %u, tx_tail = %u\n",
+ bp->tx_head, bp->tx_tail);
return NETDEV_TX_BUSY;
}
entry = bp->tx_head;
- dev_dbg(&bp->pdev->dev, "Allocated ring entry %u\n", entry);
+ netdev_dbg(bp->dev, "Allocated ring entry %u\n", entry);
mapping = dma_map_single(&bp->pdev->dev, skb->data,
len, DMA_TO_DEVICE);
bp->tx_skb[entry].skb = skb;
bp->tx_skb[entry].mapping = mapping;
- dev_dbg(&bp->pdev->dev, "Mapped skb data %p to DMA addr %08lx\n",
- skb->data, (unsigned long)mapping);
+ netdev_dbg(bp->dev, "Mapped skb data %p to DMA addr %08lx\n",
+ skb->data, (unsigned long)mapping);
ctrl = MACB_BF(TX_FRMLEN, len);
ctrl |= MACB_BIT(TX_LAST);
&bp->rx_ring_dma, GFP_KERNEL);
if (!bp->rx_ring)
goto out_err;
- dev_dbg(&bp->pdev->dev,
- "Allocated RX ring of %d bytes at %08lx (mapped %p)\n",
- size, (unsigned long)bp->rx_ring_dma, bp->rx_ring);
+ netdev_dbg(bp->dev,
+ "Allocated RX ring of %d bytes at %08lx (mapped %p)\n",
+ size, (unsigned long)bp->rx_ring_dma, bp->rx_ring);
size = TX_RING_BYTES;
bp->tx_ring = dma_alloc_coherent(&bp->pdev->dev, size,
&bp->tx_ring_dma, GFP_KERNEL);
if (!bp->tx_ring)
goto out_err;
- dev_dbg(&bp->pdev->dev,
- "Allocated TX ring of %d bytes at %08lx (mapped %p)\n",
- size, (unsigned long)bp->tx_ring_dma, bp->tx_ring);
+ netdev_dbg(bp->dev,
+ "Allocated TX ring of %d bytes at %08lx (mapped %p)\n",
+ size, (unsigned long)bp->tx_ring_dma, bp->tx_ring);
size = RX_RING_SIZE * RX_BUFFER_SIZE;
bp->rx_buffers = dma_alloc_coherent(&bp->pdev->dev, size,
&bp->rx_buffers_dma, GFP_KERNEL);
if (!bp->rx_buffers)
goto out_err;
- dev_dbg(&bp->pdev->dev,
- "Allocated RX buffers of %d bytes at %08lx (mapped %p)\n",
- size, (unsigned long)bp->rx_buffers_dma, bp->rx_buffers);
+ netdev_dbg(bp->dev,
+ "Allocated RX buffers of %d bytes at %08lx (mapped %p)\n",
+ size, (unsigned long)bp->rx_buffers_dma, bp->rx_buffers);
return 0;
struct macb *bp = netdev_priv(dev);
int err;
- dev_dbg(&bp->pdev->dev, "open\n");
+ netdev_dbg(bp->dev, "open\n");
/* if the phy is not yet register, retry later*/
if (!bp->phy_dev)
err = macb_alloc_consistent(bp);
if (err) {
- printk(KERN_ERR
- "%s: Unable to allocate DMA memory (error %d)\n",
- dev->name, err);
+ netdev_err(dev, "Unable to allocate DMA memory (error %d)\n",
+ err);
return err;
}
static int __init macb_probe(struct platform_device *pdev)
{
- struct eth_platform_data *pdata;
+ struct macb_platform_data *pdata;
struct resource *regs;
struct net_device *dev;
struct macb *bp;
spin_lock_init(&bp->lock);
-#if defined(CONFIG_ARCH_AT91)
- bp->pclk = clk_get(&pdev->dev, "macb_clk");
+ bp->pclk = clk_get(&pdev->dev, "pclk");
if (IS_ERR(bp->pclk)) {
dev_err(&pdev->dev, "failed to get macb_clk\n");
goto err_out_free_dev;
}
clk_enable(bp->pclk);
-#else
- bp->pclk = clk_get(&pdev->dev, "pclk");
- if (IS_ERR(bp->pclk)) {
- dev_err(&pdev->dev, "failed to get pclk\n");
- goto err_out_free_dev;
- }
+
bp->hclk = clk_get(&pdev->dev, "hclk");
if (IS_ERR(bp->hclk)) {
dev_err(&pdev->dev, "failed to get hclk\n");
goto err_out_put_pclk;
}
-
- clk_enable(bp->pclk);
clk_enable(bp->hclk);
-#endif
bp->regs = ioremap(regs->start, resource_size(regs));
if (!bp->regs) {
dev->irq = platform_get_irq(pdev, 0);
err = request_irq(dev->irq, macb_interrupt, 0, dev->name, dev);
if (err) {
- printk(KERN_ERR
- "%s: Unable to request IRQ %d (error %d)\n",
- dev->name, dev->irq, err);
+ dev_err(&pdev->dev, "Unable to request IRQ %d (error %d)\n",
+ dev->irq, err);
goto err_out_iounmap;
}
platform_set_drvdata(pdev, dev);
- printk(KERN_INFO "%s: Atmel MACB at 0x%08lx irq %d (%pM)\n",
- dev->name, dev->base_addr, dev->irq, dev->dev_addr);
+ netdev_info(dev, "Atmel MACB at 0x%08lx irq %d (%pM)\n",
+ dev->base_addr, dev->irq, dev->dev_addr);
phydev = bp->phy_dev;
- printk(KERN_INFO "%s: attached PHY driver [%s] "
- "(mii_bus:phy_addr=%s, irq=%d)\n", dev->name,
- phydev->drv->name, dev_name(&phydev->dev), phydev->irq);
+ netdev_info(dev, "attached PHY driver [%s] (mii_bus:phy_addr=%s, irq=%d)\n",
+ phydev->drv->name, dev_name(&phydev->dev), phydev->irq);
return 0;
err_out_iounmap:
iounmap(bp->regs);
err_out_disable_clocks:
-#ifndef CONFIG_ARCH_AT91
clk_disable(bp->hclk);
clk_put(bp->hclk);
-#endif
clk_disable(bp->pclk);
-#ifndef CONFIG_ARCH_AT91
err_out_put_pclk:
-#endif
clk_put(bp->pclk);
err_out_free_dev:
free_netdev(dev);
unregister_netdev(dev);
free_irq(dev->irq, dev);
iounmap(bp->regs);
-#ifndef CONFIG_ARCH_AT91
clk_disable(bp->hclk);
clk_put(bp->hclk);
-#endif
clk_disable(bp->pclk);
clk_put(bp->pclk);
free_netdev(dev);
netif_device_detach(netdev);
-#ifndef CONFIG_ARCH_AT91
clk_disable(bp->hclk);
-#endif
clk_disable(bp->pclk);
return 0;
struct macb *bp = netdev_priv(netdev);
clk_enable(bp->pclk);
-#ifndef CONFIG_ARCH_AT91
clk_enable(bp->hclk);
-#endif
netif_device_attach(netdev);
#include <mach/at91_rtc.h>
+#define at91_rtc_read(field) \
+ __raw_readl(at91_rtc_regs + field)
+#define at91_rtc_write(field, val) \
+ __raw_writel((val), at91_rtc_regs + field)
#define AT91_RTC_EPOCH 1900UL /* just like arch/arm/common/rtctime.c */
static DECLARE_COMPLETION(at91_rtc_updated);
static unsigned int at91_alarm_year = AT91_RTC_EPOCH;
+static void __iomem *at91_rtc_regs;
+static int irq;
/*
* Decode time/date into rtc_time structure
/* must read twice in case it changes */
do {
- time = at91_sys_read(timereg);
- date = at91_sys_read(calreg);
- } while ((time != at91_sys_read(timereg)) ||
- (date != at91_sys_read(calreg)));
+ time = at91_rtc_read(timereg);
+ date = at91_rtc_read(calreg);
+ } while ((time != at91_rtc_read(timereg)) ||
+ (date != at91_rtc_read(calreg)));
tm->tm_sec = bcd2bin((time & AT91_RTC_SEC) >> 0);
tm->tm_min = bcd2bin((time & AT91_RTC_MIN) >> 8);
tm->tm_hour, tm->tm_min, tm->tm_sec);
/* Stop Time/Calendar from counting */
- cr = at91_sys_read(AT91_RTC_CR);
- at91_sys_write(AT91_RTC_CR, cr | AT91_RTC_UPDCAL | AT91_RTC_UPDTIM);
+ cr = at91_rtc_read(AT91_RTC_CR);
+ at91_rtc_write(AT91_RTC_CR, cr | AT91_RTC_UPDCAL | AT91_RTC_UPDTIM);
- at91_sys_write(AT91_RTC_IER, AT91_RTC_ACKUPD);
+ at91_rtc_write(AT91_RTC_IER, AT91_RTC_ACKUPD);
wait_for_completion(&at91_rtc_updated); /* wait for ACKUPD interrupt */
- at91_sys_write(AT91_RTC_IDR, AT91_RTC_ACKUPD);
+ at91_rtc_write(AT91_RTC_IDR, AT91_RTC_ACKUPD);
- at91_sys_write(AT91_RTC_TIMR,
+ at91_rtc_write(AT91_RTC_TIMR,
bin2bcd(tm->tm_sec) << 0
| bin2bcd(tm->tm_min) << 8
| bin2bcd(tm->tm_hour) << 16);
- at91_sys_write(AT91_RTC_CALR,
+ at91_rtc_write(AT91_RTC_CALR,
bin2bcd((tm->tm_year + 1900) / 100) /* century */
| bin2bcd(tm->tm_year % 100) << 8 /* year */
| bin2bcd(tm->tm_mon + 1) << 16 /* tm_mon starts at zero */
| bin2bcd(tm->tm_mday) << 24);
/* Restart Time/Calendar */
- cr = at91_sys_read(AT91_RTC_CR);
- at91_sys_write(AT91_RTC_CR, cr & ~(AT91_RTC_UPDCAL | AT91_RTC_UPDTIM));
+ cr = at91_rtc_read(AT91_RTC_CR);
+ at91_rtc_write(AT91_RTC_CR, cr & ~(AT91_RTC_UPDCAL | AT91_RTC_UPDTIM));
return 0;
}
tm->tm_yday = rtc_year_days(tm->tm_mday, tm->tm_mon, tm->tm_year);
tm->tm_year = at91_alarm_year - 1900;
- alrm->enabled = (at91_sys_read(AT91_RTC_IMR) & AT91_RTC_ALARM)
+ alrm->enabled = (at91_rtc_read(AT91_RTC_IMR) & AT91_RTC_ALARM)
? 1 : 0;
pr_debug("%s(): %4d-%02d-%02d %02d:%02d:%02d\n", __func__,
tm.tm_min = alrm->time.tm_min;
tm.tm_sec = alrm->time.tm_sec;
- at91_sys_write(AT91_RTC_IDR, AT91_RTC_ALARM);
- at91_sys_write(AT91_RTC_TIMALR,
+ at91_rtc_write(AT91_RTC_IDR, AT91_RTC_ALARM);
+ at91_rtc_write(AT91_RTC_TIMALR,
bin2bcd(tm.tm_sec) << 0
| bin2bcd(tm.tm_min) << 8
| bin2bcd(tm.tm_hour) << 16
| AT91_RTC_HOUREN | AT91_RTC_MINEN | AT91_RTC_SECEN);
- at91_sys_write(AT91_RTC_CALALR,
+ at91_rtc_write(AT91_RTC_CALALR,
bin2bcd(tm.tm_mon + 1) << 16 /* tm_mon starts at zero */
| bin2bcd(tm.tm_mday) << 24
| AT91_RTC_DATEEN | AT91_RTC_MTHEN);
if (alrm->enabled) {
- at91_sys_write(AT91_RTC_SCCR, AT91_RTC_ALARM);
- at91_sys_write(AT91_RTC_IER, AT91_RTC_ALARM);
+ at91_rtc_write(AT91_RTC_SCCR, AT91_RTC_ALARM);
+ at91_rtc_write(AT91_RTC_IER, AT91_RTC_ALARM);
}
pr_debug("%s(): %4d-%02d-%02d %02d:%02d:%02d\n", __func__,
pr_debug("%s(): cmd=%08x\n", __func__, enabled);
if (enabled) {
- at91_sys_write(AT91_RTC_SCCR, AT91_RTC_ALARM);
- at91_sys_write(AT91_RTC_IER, AT91_RTC_ALARM);
+ at91_rtc_write(AT91_RTC_SCCR, AT91_RTC_ALARM);
+ at91_rtc_write(AT91_RTC_IER, AT91_RTC_ALARM);
} else
- at91_sys_write(AT91_RTC_IDR, AT91_RTC_ALARM);
+ at91_rtc_write(AT91_RTC_IDR, AT91_RTC_ALARM);
return 0;
}
*/
static int at91_rtc_proc(struct device *dev, struct seq_file *seq)
{
- unsigned long imr = at91_sys_read(AT91_RTC_IMR);
+ unsigned long imr = at91_rtc_read(AT91_RTC_IMR);
seq_printf(seq, "update_IRQ\t: %s\n",
(imr & AT91_RTC_ACKUPD) ? "yes" : "no");
unsigned int rtsr;
unsigned long events = 0;
- rtsr = at91_sys_read(AT91_RTC_SR) & at91_sys_read(AT91_RTC_IMR);
+ rtsr = at91_rtc_read(AT91_RTC_SR) & at91_rtc_read(AT91_RTC_IMR);
if (rtsr) { /* this interrupt is shared! Is it ours? */
if (rtsr & AT91_RTC_ALARM)
events |= (RTC_AF | RTC_IRQF);
if (rtsr & AT91_RTC_ACKUPD)
complete(&at91_rtc_updated);
- at91_sys_write(AT91_RTC_SCCR, rtsr); /* clear status reg */
+ at91_rtc_write(AT91_RTC_SCCR, rtsr); /* clear status reg */
rtc_update_irq(rtc, 1, events);
static int __init at91_rtc_probe(struct platform_device *pdev)
{
struct rtc_device *rtc;
- int ret;
+ struct resource *regs;
+ int ret = 0;
- at91_sys_write(AT91_RTC_CR, 0);
- at91_sys_write(AT91_RTC_MR, 0); /* 24 hour mode */
+ regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!regs) {
+ dev_err(&pdev->dev, "no mmio resource defined\n");
+ return -ENXIO;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "no irq resource defined\n");
+ return -ENXIO;
+ }
+
+ at91_rtc_regs = ioremap(regs->start, resource_size(regs));
+ if (!at91_rtc_regs) {
+ dev_err(&pdev->dev, "failed to map registers, aborting.\n");
+ return -ENOMEM;
+ }
+
+ at91_rtc_write(AT91_RTC_CR, 0);
+ at91_rtc_write(AT91_RTC_MR, 0); /* 24 hour mode */
/* Disable all interrupts */
- at91_sys_write(AT91_RTC_IDR, AT91_RTC_ACKUPD | AT91_RTC_ALARM |
+ at91_rtc_write(AT91_RTC_IDR, AT91_RTC_ACKUPD | AT91_RTC_ALARM |
AT91_RTC_SECEV | AT91_RTC_TIMEV |
AT91_RTC_CALEV);
- ret = request_irq(AT91_ID_SYS, at91_rtc_interrupt,
+ ret = request_irq(irq, at91_rtc_interrupt,
IRQF_SHARED,
"at91_rtc", pdev);
if (ret) {
printk(KERN_ERR "at91_rtc: IRQ %d already in use.\n",
- AT91_ID_SYS);
+ irq);
return ret;
}
rtc = rtc_device_register(pdev->name, &pdev->dev,
&at91_rtc_ops, THIS_MODULE);
if (IS_ERR(rtc)) {
- free_irq(AT91_ID_SYS, pdev);
+ free_irq(irq, pdev);
return PTR_ERR(rtc);
}
platform_set_drvdata(pdev, rtc);
struct rtc_device *rtc = platform_get_drvdata(pdev);
/* Disable all interrupts */
- at91_sys_write(AT91_RTC_IDR, AT91_RTC_ACKUPD | AT91_RTC_ALARM |
+ at91_rtc_write(AT91_RTC_IDR, AT91_RTC_ACKUPD | AT91_RTC_ALARM |
AT91_RTC_SECEV | AT91_RTC_TIMEV |
AT91_RTC_CALEV);
- free_irq(AT91_ID_SYS, pdev);
+ free_irq(irq, pdev);
rtc_device_unregister(rtc);
platform_set_drvdata(pdev, NULL);
/* this IRQ is shared with DBGU and other hardware which isn't
* necessarily doing PM like we are...
*/
- at91_rtc_imr = at91_sys_read(AT91_RTC_IMR)
+ at91_rtc_imr = at91_rtc_read(AT91_RTC_IMR)
& (AT91_RTC_ALARM|AT91_RTC_SECEV);
if (at91_rtc_imr) {
if (device_may_wakeup(dev))
- enable_irq_wake(AT91_ID_SYS);
+ enable_irq_wake(irq);
else
- at91_sys_write(AT91_RTC_IDR, at91_rtc_imr);
+ at91_rtc_write(AT91_RTC_IDR, at91_rtc_imr);
}
return 0;
}
{
if (at91_rtc_imr) {
if (device_may_wakeup(dev))
- disable_irq_wake(AT91_ID_SYS);
+ disable_irq_wake(irq);
else
- at91_sys_write(AT91_RTC_IER, at91_rtc_imr);
+ at91_rtc_write(AT91_RTC_IER, at91_rtc_imr);
}
return 0;
}
/* rm9200 needs manual D+ pullup; off by default */
if (cpu_is_at91rm9200()) {
- if (udc->board.pullup_pin <= 0) {
+ if (gpio_is_valid(udc->board.pullup_pin)) {
DBG("no D+ pullup?\n");
retval = -ENODEV;
goto fail0;
DBG("request irq %d failed\n", udc->udp_irq);
goto fail1;
}
- if (udc->board.vbus_pin > 0) {
+ if (gpio_is_valid(udc->board.vbus_pin)) {
retval = gpio_request(udc->board.vbus_pin, "udc_vbus");
if (retval < 0) {
DBG("request vbus pin failed\n");
INFO("%s version %s\n", driver_name, DRIVER_VERSION);
return 0;
fail4:
- if (udc->board.vbus_pin > 0 && !udc->board.vbus_polled)
+ if (gpio_is_valid(udc->board.vbus_pin) && !udc->board.vbus_polled)
free_irq(udc->board.vbus_pin, udc);
fail3:
- if (udc->board.vbus_pin > 0)
+ if (gpio_is_valid(udc->board.vbus_pin))
gpio_free(udc->board.vbus_pin);
fail2:
free_irq(udc->udp_irq, udc);
device_init_wakeup(&pdev->dev, 0);
remove_debug_file(udc);
- if (udc->board.vbus_pin > 0) {
+ if (gpio_is_valid(udc->board.vbus_pin)) {
free_irq(udc->board.vbus_pin, udc);
gpio_free(udc->board.vbus_pin);
}
enable_irq_wake(udc->udp_irq);
udc->active_suspend = wake;
- if (udc->board.vbus_pin > 0 && !udc->board.vbus_polled && wake)
+ if (gpio_is_valid(udc->board.vbus_pin) && !udc->board.vbus_polled && wake)
enable_irq_wake(udc->board.vbus_pin);
return 0;
}
struct at91_udc *udc = platform_get_drvdata(pdev);
unsigned long flags;
- if (udc->board.vbus_pin > 0 && !udc->board.vbus_polled &&
+ if (gpio_is_valid(udc->board.vbus_pin) && !udc->board.vbus_polled &&
udc->active_suspend)
disable_irq_wake(udc->board.vbus_pin);
if (port < 0 || port >= 2)
return;
- if (pdata->vbus_pin[port] <= 0)
+ if (!gpio_is_valid(pdata->vbus_pin[port]))
return;
gpio_set_value(pdata->vbus_pin[port], !pdata->vbus_pin_inverted ^ enable);
if (port < 0 || port >= 2)
return -EINVAL;
- if (pdata->vbus_pin[port] <= 0)
+ if (!gpio_is_valid(pdata->vbus_pin[port]))
return -EINVAL;
return gpio_get_value(pdata->vbus_pin[port]) ^ !pdata->vbus_pin_inverted;
if (pdata) {
for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) {
- if (pdata->vbus_pin[i] <= 0)
+ if (!gpio_is_valid(pdata->vbus_pin[i]))
continue;
gpio_request(pdata->vbus_pin[i], "ohci_vbus");
ohci_at91_usb_set_power(pdata, i, 1);
for (i = 0; i < ARRAY_SIZE(pdata->overcurrent_pin); i++) {
int ret;
- if (pdata->overcurrent_pin[i] <= 0)
+ if (!gpio_is_valid(pdata->overcurrent_pin[i]))
continue;
gpio_request(pdata->overcurrent_pin[i], "ohci_overcurrent");
if (pdata) {
for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) {
- if (pdata->vbus_pin[i] <= 0)
+ if (!gpio_is_valid(pdata->vbus_pin[i]))
continue;
ohci_at91_usb_set_power(pdata, i, 0);
gpio_free(pdata->vbus_pin[i]);
}
for (i = 0; i < ARRAY_SIZE(pdata->overcurrent_pin); i++) {
- if (pdata->overcurrent_pin[i] <= 0)
+ if (!gpio_is_valid(pdata->overcurrent_pin[i]))
continue;
free_irq(gpio_to_irq(pdata->overcurrent_pin[i]), pdev);
gpio_free(pdata->overcurrent_pin[i]);
#define DRV_NAME "AT91SAM9 Watchdog"
+#define wdt_read(field) \
+ __raw_readl(at91wdt_private.base + field)
+#define wdt_write(field, val) \
+ __raw_writel((val), at91wdt_private.base + field)
+
/* AT91SAM9 watchdog runs a 12bit counter @ 256Hz,
* use this to convert a watchdog
* value from/to milliseconds.
static void at91_ping(unsigned long data);
static struct {
+ void __iomem *base;
unsigned long next_heartbeat; /* the next_heartbeat for the timer */
unsigned long open;
char expect_close;
*/
static inline void at91_wdt_reset(void)
{
- at91_sys_write(AT91_WDT_CR, AT91_WDT_KEY | AT91_WDT_WDRSTT);
+ wdt_write(AT91_WDT_CR, AT91_WDT_KEY | AT91_WDT_WDRSTT);
}
/*
unsigned int mr;
/* Check if disabled */
- mr = at91_sys_read(AT91_WDT_MR);
+ mr = wdt_read(AT91_WDT_MR);
if (mr & AT91_WDT_WDDIS) {
printk(KERN_ERR DRV_NAME": sorry, watchdog is disabled\n");
return -EIO;
| AT91_WDT_WDDBGHLT /* disabled in debug mode */
| AT91_WDT_WDD /* restart at any time */
| (timeout & AT91_WDT_WDV); /* timer value */
- at91_sys_write(AT91_WDT_MR, reg);
+ wdt_write(AT91_WDT_MR, reg);
return 0;
}
static int __init at91wdt_probe(struct platform_device *pdev)
{
+ struct resource *r;
int res;
if (at91wdt_miscdev.parent)
return -EBUSY;
at91wdt_miscdev.parent = &pdev->dev;
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!r)
+ return -ENODEV;
+ at91wdt_private.base = ioremap(r->start, resource_size(r));
+ if (!at91wdt_private.base) {
+ dev_err(&pdev->dev, "failed to map registers, aborting.\n");
+ return -ENOMEM;
+ }
+
/* Set watchdog */
res = at91_wdt_settimeout(ms_to_ticks(WDT_HW_TIMEOUT * 1000));
if (res)
#ifndef AT91_WDT_H
#define AT91_WDT_H
-#define AT91_WDT_CR (AT91_WDT + 0x00) /* Watchdog Control Register */
+#define AT91_WDT_CR 0x00 /* Watchdog Control Register */
#define AT91_WDT_WDRSTT (1 << 0) /* Restart */
#define AT91_WDT_KEY (0xa5 << 24) /* KEY Password */
-#define AT91_WDT_MR (AT91_WDT + 0x04) /* Watchdog Mode Register */
+#define AT91_WDT_MR 0x04 /* Watchdog Mode Register */
#define AT91_WDT_WDV (0xfff << 0) /* Counter Value */
#define AT91_WDT_WDFIEN (1 << 12) /* Fault Interrupt Enable */
#define AT91_WDT_WDRSTEN (1 << 13) /* Reset Processor */
#define AT91_WDT_WDDBGHLT (1 << 28) /* Debug Halt */
#define AT91_WDT_WDIDLEHLT (1 << 29) /* Idle Halt */
-#define AT91_WDT_SR (AT91_WDT + 0x08) /* Watchdog Status Register */
+#define AT91_WDT_SR 0x08 /* Watchdog Status Register */
#define AT91_WDT_WDUNF (1 << 0) /* Watchdog Underflow */
#define AT91_WDT_WDERR (1 << 1) /* Watchdog Error */
--- /dev/null
+/*
+ * Copyright (C) 2004-2006 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __MACB_PDATA_H__
+#define __MACB_PDATA_H__
+
+struct macb_platform_data {
+ u32 phy_mask;
+ int phy_irq_pin; /* PHY IRQ */
+ u8 is_rmii; /* using RMII interface? */
+};
+
+#endif /* __MACB_PDATA_H__ */
--- /dev/null
+/*
+ * Copyright (C) 2011 Texas Instruments Inc
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation version 2.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#ifndef _VPIF_TYPES_H
+#define _VPIF_TYPES_H
+
+#define VPIF_CAPTURE_MAX_CHANNELS 2
+
+enum vpif_if_type {
+ VPIF_IF_BT656,
+ VPIF_IF_BT1120,
+ VPIF_IF_RAW_BAYER
+};
+
+struct vpif_interface {
+ enum vpif_if_type if_type;
+ unsigned hd_pol:1;
+ unsigned vd_pol:1;
+ unsigned fid_pol:1;
+};
+
+struct vpif_subdev_info {
+ const char *name;
+ struct i2c_board_info board_info;
+ u32 input;
+ u32 output;
+ unsigned can_route:1;
+ struct vpif_interface vpif_if;
+};
+
+struct vpif_display_config {
+ int (*set_clock)(int, int);
+ struct vpif_subdev_info *subdevinfo;
+ int subdev_count;
+ const char **output;
+ int output_count;
+ const char *card_name;
+};
+
+struct vpif_input {
+ struct v4l2_input input;
+ const char *subdev_name;
+};
+
+struct vpif_capture_chan_config {
+ const struct vpif_input *inputs;
+ int input_count;
+};
+
+struct vpif_capture_config {
+ int (*setup_input_channel_mode)(int);
+ int (*setup_input_path)(int, const char *);
+ struct vpif_capture_chan_config chan_config[VPIF_CAPTURE_MAX_CHANNELS];
+ struct vpif_subdev_info *subdev_info;
+ int subdev_count;
+ const char *card_name;
+};
+#endif /* _VPIF_TYPES_H */
projects / firefly-linux-kernel-4.4.55.git / commitdiff